Kai Huang [Tue, 15 Aug 2023 11:02:05 +0000 (23:02 +1200)]
x86/virt/tdx: Make TDX_MODULE_CALL handle SEAMCALL #UD and #GP
SEAMCALL instruction causes #UD if the CPU isn't in VMX operation.
Currently the TDX_MODULE_CALL assembly doesn't handle #UD, thus making
SEAMCALL when VMX is disabled would cause Oops.
Unfortunately, there are legal cases that SEAMCALL can be made when VMX
is disabled. For instance, VMX can be disabled due to emergency reboot
while there are still TDX guests running.
Extend the TDX_MODULE_CALL assembly to return an error code for #UD to
handle this case gracefully, e.g., KVM can then quietly eat all SEAMCALL
errors caused by emergency reboot.
SEAMCALL instruction also causes #GP when TDX isn't enabled by the BIOS.
Use _ASM_EXTABLE_FAULT() to catch both exceptions with the trap number
recorded, and define two new error codes by XORing the trap number to
the TDX_SW_ERROR. This opportunistically handles #GP too while using
the same simple assembly code.
A bonus is when kernel mistakenly calls SEAMCALL when CPU isn't in VMX
operation, or when TDX isn't enabled by the BIOS, or when the BIOS is
buggy, the kernel can get a nicer error code rather than a less
understandable Oops.
Kai Huang [Tue, 15 Aug 2023 11:02:04 +0000 (23:02 +1200)]
x86/virt/tdx: Wire up basic SEAMCALL functions
Intel Trust Domain Extensions (TDX) protects guest VMs from malicious
host and certain physical attacks. A CPU-attested software module
called 'the TDX module' runs inside a new isolated memory range as a
trusted hypervisor to manage and run protected VMs.
TDX introduces a new CPU mode: Secure Arbitration Mode (SEAM). This
mode runs only the TDX module itself or other code to load the TDX
module.
The host kernel communicates with SEAM software via a new SEAMCALL
instruction. This is conceptually similar to a guest->host hypercall,
except it is made from the host to SEAM software instead. The TDX
module establishes a new SEAMCALL ABI which allows the host to
initialize the module and to manage VMs.
The SEAMCALL ABI is very similar to the TDCALL ABI and leverages much
TDCALL infrastructure. Wire up basic functions to make SEAMCALLs for
the basic support of running TDX guests: __seamcall(), __seamcall_ret(),
and __seamcall_saved_ret() for TDH.VP.ENTER. All SEAMCALLs involved in
the basic TDX support don't use "callee-saved" registers as input and
output, except the TDH.VP.ENTER.
To start to support TDX, create a new arch/x86/virt/vmx/tdx/tdx.c for
TDX host kernel support. Add a new Kconfig option CONFIG_INTEL_TDX_HOST
to opt-in TDX host kernel support (to distinguish with TDX guest kernel
support). So far only KVM uses TDX. Make the new config option depend
on KVM_INTEL.
Kai Huang [Tue, 15 Aug 2023 11:02:03 +0000 (23:02 +1200)]
x86/tdx: Remove 'struct tdx_hypercall_args'
Now 'struct tdx_hypercall_args' is basically 'struct tdx_module_args'
minus RCX. Although from __tdx_hypercall()'s perspective RCX isn't
used as shared register thus not part of input/output registers, it's
not worth to have a separate structure just due to one register.
Remove the 'struct tdx_hypercall_args' and use 'struct tdx_module_args'
instead in __tdx_hypercall() related code. This also saves the memory
copy between the two structures within __tdx_hypercall().
Kai Huang [Tue, 15 Aug 2023 11:02:02 +0000 (23:02 +1200)]
x86/tdx: Reimplement __tdx_hypercall() using TDX_MODULE_CALL asm
Now the TDX_HYPERCALL asm is basically identical to the TDX_MODULE_CALL
with both '\saved' and '\ret' enabled, with two minor things though:
1) The way to restore the structure pointer is different
The TDX_HYPERCALL uses RCX as spare to restore the structure pointer,
but the TDX_MODULE_CALL assumes no spare register can be used. In other
words, TDX_MODULE_CALL already covers what TDX_HYPERCALL does.
2) TDX_MODULE_CALL only clears shared registers for TDH.VP.ENTER
For this just need to make that code available for the non-host case.
Thus, remove the TDX_HYPERCALL and reimplement the __tdx_hypercall()
using the TDX_MODULE_CALL.
Extend the TDX_MODULE_CALL to cover "clear shared registers" for
TDG.VP.VMCALL. Introduce a new __tdcall_saved_ret() to replace the
temporary __tdcall_hypercall().
The __tdcall_saved_ret() can also be used for those new TDCALLs which
require more input/output registers than the basic TDCALLs do.
Kai Huang [Tue, 15 Aug 2023 11:02:01 +0000 (23:02 +1200)]
x86/tdx: Make TDX_HYPERCALL asm similar to TDX_MODULE_CALL
Now the 'struct tdx_hypercall_args' and 'struct tdx_module_args' are
almost the same, and the TDX_HYPERCALL and TDX_MODULE_CALL asm macro
share similar code pattern too. The __tdx_hypercall() and __tdcall()
should be unified to use the same assembly code.
As a preparation to unify them, simplify the TDX_HYPERCALL to make it
more like the TDX_MODULE_CALL.
The TDX_HYPERCALL takes the pointer of 'struct tdx_hypercall_args' as
function call argument, and does below extra things comparing to the
TDX_MODULE_CALL:
1) It sets RAX to 0 (TDG.VP.VMCALL leaf) internally;
2) It sets RCX to the (fixed) bitmap of shared registers internally;
3) It calls __tdx_hypercall_failed() internally (and panics) when the
TDCALL instruction itself fails;
4) After TDCALL, it moves R10 to RAX to return the return code of the
VMCALL leaf, regardless the '\ret' asm macro argument;
Firstly, change the TDX_HYPERCALL to take the same function call
arguments as the TDX_MODULE_CALL does: TDCALL leaf ID, and the pointer
to 'struct tdx_module_args'. Then 1) and 2) can be moved to the
caller:
- TDG.VP.VMCALL leaf ID can be passed via the function call argument;
- 'struct tdx_module_args' is 'struct tdx_hypercall_args' + RCX, thus
the bitmap of shared registers can be passed via RCX in the
structure.
Secondly, to move 3) and 4) out of assembly, make the TDX_HYPERCALL
always save output registers to the structure. The caller then can:
- Call __tdx_hypercall_failed() when TDX_HYPERCALL returns error;
- Return R10 in the structure as the return code of the VMCALL leaf;
With above changes, change the asm function from __tdx_hypercall() to
__tdcall_hypercall(), and reimplement __tdx_hypercall() as the C wrapper
of it. This avoids having to add another wrapper of __tdx_hypercall()
(_tdx_hypercall() is already taken).
The __tdcall_hypercall() will be replaced with a __tdcall() variant
using TDX_MODULE_CALL in a later commit as the final goal is to have one
assembly to handle both TDCALL and TDVMCALL.
Currently, the __tdx_hypercall() asm is in '.noinstr.text'. To keep
this unchanged, annotate __tdx_hypercall(), which is a C function now,
as 'noinstr'.
Remove the __tdx_hypercall_ret() as __tdx_hypercall() already does so.
Implement __tdx_hypercall() in tdx-shared.c so it can be shared with the
compressed code.
Opportunistically fix a checkpatch error complaining using space around
parenthesis '(' and ')' while moving the bitmap of shared registers to
<asm/shared/tdx.h>.
[ dhansen: quash new calls of __tdx_hypercall_ret() that showed up ]
Kai Huang [Tue, 15 Aug 2023 11:02:00 +0000 (23:02 +1200)]
x86/tdx: Extend TDX_MODULE_CALL to support more TDCALL/SEAMCALL leafs
The TDX guest live migration support (TDX 1.5) adds new TDCALL/SEAMCALL
leaf functions. Those new TDCALLs/SEAMCALLs take additional registers
for input (R10-R13) and output (R12-R13). TDG.SERVTD.RD is an example.
Also, the current TDX_MODULE_CALL doesn't aim to handle TDH.VP.ENTER
SEAMCALL, which monitors the TDG.VP.VMCALL in input/output registers
when it returns in case of VMCALL from TDX guest.
With those new TDCALLs/SEAMCALLs and the TDH.VP.ENTER covered, the
TDX_MODULE_CALL macro basically needs to handle the same input/output
registers as the TDX_HYPERCALL does. And as a result, they also share
similar logic in the assembly, thus should be unified to use one common
assembly.
Extend the TDX_MODULE_CALL asm to support the new TDCALLs/SEAMCALLs and
also the TDH.VP.ENTER SEAMCALL. Eventually it will be unified with the
TDX_HYPERCALL.
The new input/output registers fit with the "callee-saved" registers in
the x86 calling convention. Add a new "saved" parameter to support
those new TDCALLs/SEAMCALLs and TDH.VP.ENTER and keep the existing
TDCALLs/SEAMCALLs minimally impacted.
For TDH.VP.ENTER, after it returns the registers shared by the guest
contain guest's values. Explicitly clear them to prevent speculative
use of guest's values.
Note most TDX live migration related SEAMCALLs may also clobber AVX*
state ("AVX, AVX2 and AVX512 state: may be reset to the architectural
INIT state" -- see TDH.EXPORT.MEM for example). And TDH.VP.ENTER also
clobbers XMM0-XMM15 when the corresponding bit is set in RCX. Don't
handle them in the TDX_MODULE_CALL macro but let the caller save and
restore when needed.
Kai Huang [Tue, 15 Aug 2023 11:01:59 +0000 (23:01 +1200)]
x86/tdx: Pass TDCALL/SEAMCALL input/output registers via a structure
Currently, the TDX_MODULE_CALL asm macro, which handles both TDCALL and
SEAMCALL, takes one parameter for each input register and an optional
'struct tdx_module_output' (a collection of output registers) as output.
This is different from the TDX_HYPERCALL macro which uses a single
'struct tdx_hypercall_args' to carry all input/output registers.
The newer TDX versions introduce more TDCALLs/SEAMCALLs which use more
input/output registers. Also, the TDH.VP.ENTER (which isn't covered
by the current TDX_MODULE_CALL macro) basically can use all registers
that the TDX_HYPERCALL does. The current TDX_MODULE_CALL macro isn't
extendible to cover those cases.
Similar to the TDX_HYPERCALL macro, simplify the TDX_MODULE_CALL macro
to use a single structure 'struct tdx_module_args' to carry all the
input/output registers. Currently, R10/R11 are only used as output
register but not as input by any TDCALL/SEAMCALL. Change to also use
R10/R11 as input register to make input/output registers symmetric.
Currently, the TDX_MODULE_CALL macro depends on the caller to pass a
non-NULL 'struct tdx_module_output' to get additional output registers.
Similar to the TDX_HYPERCALL macro, change the TDX_MODULE_CALL macro to
take a new 'ret' macro argument to indicate whether to save the output
registers to the 'struct tdx_module_args'. Also introduce a new
__tdcall_ret() for that purpose, similar to the __tdx_hypercall_ret().
Note the tdcall(), which is a wrapper of __tdcall(), is called by three
callers: tdx_parse_tdinfo(), tdx_get_ve_info() and tdx_early_init().
The former two need the additional output but the last one doesn't. For
simplicity, make tdcall() always call __tdcall_ret() to avoid another
"_ret()" wrapper. The last caller tdx_early_init() isn't performance
critical anyway.
Kai Huang [Tue, 15 Aug 2023 11:01:58 +0000 (23:01 +1200)]
x86/tdx: Rename __tdx_module_call() to __tdcall()
__tdx_module_call() is only used by the TDX guest to issue TDCALL to the
TDX module. Rename it to __tdcall() to match its behaviour, e.g., it
cannot be used to make host-side SEAMCALL.
Also rename tdx_module_call() which is a wrapper of __tdx_module_call()
to tdcall().
No functional change intended.
Signed-off-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/785d20d99fbcd0db8262c94da6423375422d8c75.1692096753.git.kai.huang%40intel.com
Kai Huang [Tue, 15 Aug 2023 11:01:57 +0000 (23:01 +1200)]
x86/tdx: Make macros of TDCALLs consistent with the spec
The TDX spec names all TDCALLs with prefix "TDG". Currently, the kernel
doesn't follow such convention for the macros of those TDCALLs but uses
prefix "TDX_" for all of them. Although it's arguable whether the TDX
spec names those TDCALLs properly, it's better for the kernel to follow
the spec when naming those macros.
Change all macros of TDCALLs to make them consistent with the spec. As
a bonus, they get distinguished easily from the host-side SEAMCALLs,
which all have prefix "TDH".
No functional change intended.
Signed-off-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/516dccd0bd8fb9a0b6af30d25bb2d971aa03d598.1692096753.git.kai.huang%40intel.com
Kai Huang [Tue, 15 Aug 2023 11:01:56 +0000 (23:01 +1200)]
x86/tdx: Skip saving output regs when SEAMCALL fails with VMFailInvalid
If SEAMCALL fails with VMFailInvalid, the SEAM software (e.g., the TDX
module) won't have chance to set any output register. Skip saving the
output registers to the structure in this case.
Also, as '.Lno_output_struct' is the very last symbol before RET, rename
it to '.Lout' to make it short.
Opportunistically make the asm directives unindented.
Kai Huang [Tue, 15 Aug 2023 11:01:55 +0000 (23:01 +1200)]
x86/tdx: Zero out the missing RSI in TDX_HYPERCALL macro
In the TDX_HYPERCALL asm, after the TDCALL instruction returns from the
untrusted VMM, the registers that the TDX guest shares to the VMM need
to be cleared to avoid speculative execution of VMM-provided values.
RSI is specified in the bitmap of those registers, but it is missing
when zeroing out those registers in the current TDX_HYPERCALL.
It was there when it was originally added in commit 752d13305c78
("x86/tdx: Expand __tdx_hypercall() to handle more arguments"), but was
later removed in commit 1e70c680375a ("x86/tdx: Do not corrupt
frame-pointer in __tdx_hypercall()"), which was correct because %rsi is
later restored in the "pop %rsi". However a later commit 7a3a401874be
("x86/tdx: Drop flags from __tdx_hypercall()") removed that "pop %rsi"
but forgot to add the "xor %rsi, %rsi" back.
Fix by adding it back.
Fixes: 7a3a401874be ("x86/tdx: Drop flags from __tdx_hypercall()") Signed-off-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/e7d1157074a0b45d34564d5f17f3e0ffee8115e9.1692096753.git.kai.huang%40intel.com
TDX guest memory is private by default and the VMM may not access it.
However, in cases where the guest needs to share data with the VMM,
the guest and the VMM can coordinate to make memory shared between
them.
The guest side of this protocol includes the "MapGPA" hypercall. This
call takes a guest physical address range. The hypercall spec (aka.
the GHCI) says that the MapGPA call is allowed to return partial
progress in mapping this range and indicate that fact with a special
error code. A guest that sees such partial progress is expected to
retry the operation for the portion of the address range that was not
completed.
Hyper-V does this partial completion dance when set_memory_decrypted()
is called to "decrypt" swiotlb bounce buffers that can be up to 1GB
in size. It is evidently the only VMM that does this, which is why
nobody noticed this until now.
[ dhansen: rewrite changelog ]
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Link: https://lore.kernel.org/all/20230811021246.821-2-decui%40microsoft.com
Merge tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm ci scripts from Dave Airlie:
"This is a bunch of ci integration for the freedesktop gitlab instance
where we currently do upstream userspace testing on diverse sets of
GPU hardware. From my perspective I think it's an experiment worth
going with and seeing how the benefits/noise playout keeping these
files useful.
Ideally I'd like to get this so we can do pre-merge testing on PRs
eventually.
Below is some info from danvet on why we've ended up making the
decision and how we can roll it back if we decide it was a bad plan.
Why in upstream?
- like documentation, testcases, tools CI integration is one of these
things where you can waste endless amounts of time if you
accidentally have a version that doesn't match your source code
- but also like the above, there's a balance, this is the initial cut
of what we think makes sense to keep in sync vs out-of-tree,
probably needs adjustment
- gitlab supports out-of-repo gitlab integration and that's what's
been used for the kernel in drm, but it results in per-driver
fragmentation and lots of duplicated effort. the simple act of
smashing an arbitrary winner into a topic branch already started
surfacing patches on dri-devel and sparking good cross driver team
discussions
Why gitlab?
- it's not any more shit than any of the other CI
- drm userspace uses it extensively for everything in userspace, we
have a lot of people and experience with this, including
integration of hw testing labs
- media userspace like gstreamer is also on gitlab.fd.o, and there's
discussion to extend this to the media subsystem in some fashion
Can this be shared?
- there's definitely a pile of code that could move to scripts/ if
other subsystem adopt ci integration in upstream kernel git. other
bits are more drm/gpu specific like the igt-gpu-tests/tools
integration
- docker images can be run locally or in other CI runners
Will we regret this?
- it's all in one directory, intentionally, for easy deletion
- probably 1-2 years in upstream to see whether this is worth it or a
Big Mistake. that's roughly what it took to _really_ roll out solid
CI in the bigger userspace projects we have on gitlab.fd.o like
mesa3d"
* tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm:
drm: ci: docs: fix build warning - add missing escape
drm: Add initial ci/ subdirectory
Merge tag 'x86-urgent-2023-09-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fix preemption delays in the SGX code, remove unnecessarily
UAPI-exported code, fix a ld.lld linker (in)compatibility quirk and
make the x86 SMP init code a bit more conservative to fix kexec()
lockups"
* tag 'x86-urgent-2023-09-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sgx: Break up long non-preemptible delays in sgx_vepc_release()
x86: Remove the arch_calc_vm_prot_bits() macro from the UAPI
x86/build: Fix linker fill bytes quirk/incompatibility for ld.lld
x86/smp: Don't send INIT to non-present and non-booted CPUs
Merge tag 'perf-tools-for-v6.6-1-2023-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools updates from Arnaldo Carvalho de Melo:
"perf tools maintainership:
- Add git information for perf-tools and perf-tools-next trees and
branches to the MAINTAINERS file. That is where development now
takes place and myself and Namhyung Kim have write access, more
people to come as we emulate other maintainer groups.
perf record:
- Record kernel data maps when 'perf record --data' is used, so that
global variables can be resolved and used in tools that do data
profiling.
perf trace:
- Remove the old, experimental support for BPF events in which a .c
file was passed as an event: "perf trace -e hello.c" to then get
compiled and loaded.
The only known usage for that, that shipped with the kernel as an
example for such events, augmented the raw_syscalls tracepoints and
was converted to a libbpf skeleton, reusing all the user space
components and the BPF code connected to the syscalls.
In the end just the way to glue the BPF part and the user space
type beautifiers changed, now being performed by libbpf skeletons.
The next step is to use BTF to do pretty printing of all syscall
types, as discussed with Alan Maguire and others.
Now, on a perf built with BUILD_BPF_SKEL=1 we get most if not all
path/filenames/strings, some of the networking data structures,
perf_event_attr, etc, i.e. systemwide tracing of nanosleep calls
and perf_event_open syscalls while 'perf stat' runs 'sleep' for 5
seconds:
- Building with binutils' libopcode now is opt-in (BUILD_NONDISTRO=1)
for licensing reasons, and we missed a build test on
tools/perf/tests makefile.
Since we now default to NDEBUG=1, we ended up segfaulting when
building with BUILD_NONDISTRO=1 because a needed initialization
routine was being "error checked" via an assert.
Fix it by explicitly checking the result and aborting instead if it
fails.
We better back propagate the error, but at least 'perf annotate' on
samples collected for a BPF program is back working when perf is
built with BUILD_NONDISTRO=1.
perf report/top:
- Add back TUI hierarchy mode header, that is seen when using 'perf
report/top --hierarchy'.
- Fix the number of entries for 'e' key in the TUI that was
preventing navigation of lines when expanding an entry.
perf report/script:
- Support cross platform register handling, allowing a perf.data file
collected on one architecture to have registers sampled correctly
displayed when analysis tools such as 'perf report' and 'perf
script' are used on a different architecture.
- Fix handling of event attributes in pipe mode, i.e. when one uses:
perf record -o - | perf report -i -
When no perf.data files are used.
- Handle files generated via pipe mode with a version of perf and
then read also via pipe mode with a different version of perf,
where the event attr record may have changed, use the record size
field to properly support this version mismatch.
perf probe:
- Accessing global variables from uprobes isn't supported, make the
error message state that instead of stating that some minimal
kernel version is needed to have that feature. This seems just a
tool limitation, the kernel probably has all that is needed.
perf tests:
- Fix a reference count related leak in the dlfilter v0 API where the
result of a thread__find_symbol_fb() is not matched with an
addr_location__exit() to drop the reference counts of the resolved
components (machine, thread, map, symbol, etc). Add a dlfilter test
to make sure that doesn't regresses.
- Lots of fixes for the 'perf test' written in shell script related
to problems found with the shellcheck utility.
- Fixes for 'perf test' shell scripts testing features enabled when
perf is built with BUILD_BPF_SKEL=1, such as 'perf stat' bpf
counters.
- Add perf record sample filtering test, things like the following
example, that gets implemented as a BPF filter attached to the
event:
- Improve the way the task_analyzer test checks if libtraceevent is
linked, using 'perf version --build-options' instead of the more
expensinve 'perf record -e "sched:sched_switch"'.
- Add support for riscv in the mmap-basic test. (This went as well
via the RiscV tree, same contents).
libperf:
- Implement riscv mmap support (This went as well via the RiscV tree,
same contents).
perf script:
- New tool that converts perf.data files to the firefox profiler
format so that one can use the visualizer at
https://profiler.firefox.com/. Done by Anup Sharma as part of this
year's Google Summer of Code.
One can generate the output and upload it to the web interface but
Anup also automated everything:
perf script gecko -F 99 -a sleep 60
- Support syscall name parsing on arm64.
- Print "cgroup" field on the same line as "comm".
perf bench:
- Add new 'uprobe' benchmark to measure the overhead of uprobes
with/without BPF programs attached to it.
- breakpoints are not available on power9, skip that test.
perf stat:
- Add #num_cpus_online literal to be used in 'perf stat' metrics, and
add this extra 'perf test' check that exemplifies its purpose:
- Improve tool startup time by lazily reading PMU, JSON, sysfs data.
- Improve error reporting in the parsing of events, passing YYLTYPE
to error routines, so that the output can show were the parsing
error was found.
- Add 'perf test' entries to check the parsing of events
improvements.
- Fix various leak for things detected by -fsanitize=address, mostly
things that would be freed at tool exit, including:
- Free evsel->filter on the destructor.
- Allow tools to register a thread->priv destructor and use it in
'perf trace'.
- Free evsel->priv in 'perf trace'.
- Free string returned by synthesize_perf_probe_point() when the
caller fails to do all it needs.
- Adjust various compiler options to not consider errors some
warnings when building with broken headers found in things like
python, flex, bison, as we otherwise build with -Werror. Some for
gcc, some for clang, some for some specific version of those, some
for some specific version of flex or bison, or some specific
combination of these components, bah.
- Allow customization of clang options for BPF target, this helps
building on gentoo where there are other oddities where BPF targets
gets passed some compiler options intended for the native build, so
building with WERROR=0 helps while these oddities are fixed.
- Dont pass ERR_PTR() values to perf_session__delete() in 'perf top'
and 'perf lock', fixing some segfaults when handling some odd
failures.
- Add LTO build option.
- Fix format of unordered lists in the perf docs
(tools/perf/Documentation)
- Overhaul the bison files, using constructs such as YYNOMEM.
- Remove unused tokens from the bison .y files.
- Add more comments to various structs.
- A few LoongArch enablement patches.
Vendor events (JSON):
- Add JSON metrics for Yitian 710 DDR (aarch64). Things like:
EventName, BriefDescription
visible_window_limit_reached_rd, "At least one entry in read queue reaches the visible window limit.",
visible_window_limit_reached_wr, "At least one entry in write queue reaches the visible window limit.",
op_is_dqsosc_mpc , "A DQS Oscillator MPC command to DRAM.",
op_is_dqsosc_mrr , "A DQS Oscillator MRR command to DRAM.",
op_is_tcr_mrr , "A Temperature Compensated Refresh(TCR) MRR command to DRAM.",
- Add AmpereOne metrics (aarch64).
- Update N2 and V2 metrics (aarch64) and events using Arm telemetry
repo.
- Update scale units and descriptions of common topdown metrics on
aarch64. Things like:
- "MetricExpr": "stall_slot_frontend / (#slots * cpu_cycles)",
- "BriefDescription": "Frontend bound L1 topdown metric",
+ "MetricExpr": "100 * (stall_slot_frontend / (#slots * cpu_cycles))",
+ "BriefDescription": "This metric is the percentage of total slots that were stalled due to resource constraints in the frontend of the processor.",
- Update events for intel: meteorlake to 1.04, sapphirerapids to
1.15, Icelake+ metric constraints.
- Update files for the power10 platform"
* tag 'perf-tools-for-v6.6-1-2023-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: (217 commits)
perf parse-events: Fix driver config term
perf parse-events: Fixes relating to no_value terms
perf parse-events: Fix propagation of term's no_value when cloning
perf parse-events: Name the two term enums
perf list: Don't print Unit for "default_core"
perf vendor events intel: Fix modifier in tma_info_system_mem_parallel_reads for skylake
perf dlfilter: Avoid leak in v0 API test use of resolve_address()
perf metric: Add #num_cpus_online literal
perf pmu: Remove str from perf_pmu_alias
perf parse-events: Make common term list to strbuf helper
perf parse-events: Minor help message improvements
perf pmu: Avoid uninitialized use of alias->str
perf jevents: Use "default_core" for events with no Unit
perf test stat_bpf_counters_cgrp: Enhance perf stat cgroup BPF counter test
perf test shell stat_bpf_counters: Fix test on Intel
perf test shell record_bpf_filter: Skip 6.2 kernel
libperf: Get rid of attr.id field
perf tools: Convert to perf_record_header_attr_id()
libperf: Add perf_record_header_attr_id()
perf tools: Handle old data in PERF_RECORD_ATTR
...
Merge tag '6.6-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- six smb3 client fixes including ones to allow controlling smb3
directory caching timeout and limits, and one debugging improvement
- one fix for nls Kconfig (don't need to expose NLS_UCS2_UTILS option)
- one minor spnego registry update
* tag '6.6-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
spnego: add missing OID to oid registry
smb3: fix minor typo in SMB2_GLOBAL_CAP_LARGE_MTU
cifs: update internal module version number for cifs.ko
smb3: allow controlling maximum number of cached directories
smb3: add trace point for queryfs (statfs)
nls: Hide new NLS_UCS2_UTILS
smb3: allow controlling length of time directory entries are cached with dir leases
smb: propagate error code of extract_sharename()
David Howells [Fri, 8 Sep 2023 16:03:22 +0000 (17:03 +0100)]
iov_iter: Kunit tests for page extraction
Add some kunit tests for page extraction for ITER_BVEC, ITER_KVEC and
ITER_XARRAY type iterators. ITER_UBUF and ITER_IOVEC aren't dealt with
as they require userspace VM interaction. ITER_DISCARD isn't dealt with
either as that can't be extracted.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Christian Brauner <brauner@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 8 Sep 2023 16:03:21 +0000 (17:03 +0100)]
iov_iter: Kunit tests for copying to/from an iterator
Add some kunit tests for page extraction for ITER_BVEC, ITER_KVEC and
ITER_XARRAY type iterators. ITER_UBUF and ITER_IOVEC aren't dealt with
as they require userspace VM interaction. ITER_DISCARD isn't dealt with
either as that does nothing.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Christian Brauner <brauner@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 8 Sep 2023 16:03:20 +0000 (17:03 +0100)]
iov_iter: Fix iov_iter_extract_pages() with zero-sized entries
iov_iter_extract_pages() doesn't correctly handle skipping over initial
zero-length entries in ITER_KVEC and ITER_BVEC-type iterators.
The problem is that it accidentally reduces maxsize to 0 when it
skipping and thus runs to the end of the array and returns 0.
Fix this by sticking the calculated size-to-copy in a new variable
rather than back in maxsize.
Fixes: 7d58fe731028 ("iov_iter: Add a function to extract a page list from an iterator") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Christian Brauner <brauner@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'riscv-for-linus-6.6-mw2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- The kernel now dynamically probes for misaligned access speed, as
opposed to relying on a table of known implementations.
- Support for non-coherent devices on systems using the Andes AX45MP
core, including the RZ/Five SoCs.
- Support for the V extension in ptrace(), again.
- Support for KASLR.
- Support for the BPF prog pack allocator in RISC-V.
- A handful of bug fixes and cleanups.
* tag 'riscv-for-linus-6.6-mw2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (25 commits)
soc: renesas: Kconfig: For ARCH_R9A07G043 select the required configs if dependencies are met
riscv: Kconfig.errata: Add dependency for RISCV_SBI in ERRATA_ANDES config
riscv: Kconfig.errata: Drop dependency for MMU in ERRATA_ANDES_CMO config
riscv: Kconfig: Select DMA_DIRECT_REMAP only if MMU is enabled
bpf, riscv: use prog pack allocator in the BPF JIT
riscv: implement a memset like function for text
riscv: extend patch_text_nosync() for multiple pages
bpf: make bpf_prog_pack allocator portable
riscv: libstub: Implement KASLR by using generic functions
libstub: Fix compilation warning for rv32
arm64: libstub: Move KASLR handling functions to kaslr.c
riscv: Dump out kernel offset information on panic
riscv: Introduce virtual kernel mapping KASLR
RISC-V: Add ptrace support for vectors
soc: renesas: Kconfig: Select the required configs for RZ/Five SoC
cache: Add L2 cache management for Andes AX45MP RISC-V core
dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller
riscv: mm: dma-noncoherent: nonstandard cache operations support
riscv: errata: Add Andes alternative ports
riscv: asm: vendorid_list: Add Andes Technology to the vendors list
...
Duoming Zhou [Wed, 2 Aug 2023 03:37:37 +0000 (11:37 +0800)]
sh: push-switch: Reorder cleanup operations to avoid use-after-free bug
The original code puts flush_work() before timer_shutdown_sync()
in switch_drv_remove(). Although we use flush_work() to stop
the worker, it could be rescheduled in switch_timer(). As a result,
a use-after-free bug can occur. The details are shown below:
This patch puts timer_shutdown_sync() before flush_work() to
mitigate the bugs. As a result, the worker and timer will be
stopped safely before the deallocate operations.
Fixes: 9f5e8eee5cfe ("sh: generic push-switch framework.") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Link: https://lore.kernel.org/r/20230802033737.9738-1-duoming@zju.edu.cn Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Petr Tesarik [Mon, 24 Jul 2023 12:07:42 +0000 (14:07 +0200)]
sh: boards: Fix CEU buffer size passed to dma_declare_coherent_memory()
In all these cases, the last argument to dma_declare_coherent_memory() is
the buffer end address, but the expected value should be the size of the
reserved region.
Fixes: 39fb993038e1 ("media: arch: sh: ap325rxa: Use new renesas-ceu camera driver") Fixes: c2f9b05fd5c1 ("media: arch: sh: ecovec: Use new renesas-ceu camera driver") Fixes: f3590dc32974 ("media: arch: sh: kfr2r09: Use new renesas-ceu camera driver") Fixes: 186c446f4b84 ("media: arch: sh: migor: Use new renesas-ceu camera driver") Fixes: 1a3c230b4151 ("media: arch: sh: ms7724se: Use new renesas-ceu camera driver") Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Link: https://lore.kernel.org/r/20230724120742.2187-1-petrtesarik@huaweicloud.com Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small stragglers that missed the initial merge.
Driver updates are qla2xxx and smartpqi (mp3sas has a high diffstat
due to the volatile qualifier removal, fnic due to unused function
removal and sd.c has a lot of code shuffling to remove forward
declarations)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: ufs: core: No need to update UPIU.header.flags and lun in advanced RPMB handler
scsi: ufs: core: Add advanced RPMB support where UFSHCI 4.0 does not support EHS length in UTRD
scsi: mpt3sas: Remove volatile qualifier
scsi: mpt3sas: Perform additional retries if doorbell read returns 0
scsi: libsas: Simplify sas_queue_reset() and remove unused code
scsi: ufs: Fix the build for the old ARM OABI
scsi: qla2xxx: Fix unused variable warning in qla2xxx_process_purls_pkt()
scsi: fnic: Remove unused functions fnic_scsi_host_start/end_tag()
scsi: qla2xxx: Fix spelling mistake "tranport" -> "transport"
scsi: fnic: Replace sgreset tag with max_tag_id
scsi: qla2xxx: Remove unused variables in qla24xx_build_scsi_type_6_iocbs()
scsi: qla2xxx: Fix nvme_fc_rcv_ls_req() undefined error
scsi: smartpqi: Change driver version to 2.1.24-046
scsi: smartpqi: Enhance error messages
scsi: smartpqi: Enhance controller offline notification
scsi: smartpqi: Enhance shutdown notification
scsi: smartpqi: Simplify lun_number assignment
scsi: smartpqi: Rename pciinfo to pci_info
scsi: smartpqi: Rename MACRO to clarify purpose
scsi: smartpqi: Add abort handler
...
Merge tag 'driver-core-6.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver symbol lookup fix from Greg KH:
"Here is one last fixup for your tree for 6.6-rc1. It resolves a
problem with the way that symbol_get was changed in the module tree
merge in your tree to fix up the DVB drivers which rely on this old
api to attach new devices.
As the changelog comment says:
In commit 9011e49d54dc ("modules: only allow symbol_get of
EXPORT_SYMBOL_GPL modules") the use of symbol_get is properly
restricted to GPL-only marked symbols. This interacts oddly with the
DVB logic which only uses dvb_attach() to load the dvb driver which
then uses symbol_get().
Fix this up by properly marking all of the dvb_attach attach symbols
as EXPORT_SYMBOL_GPL().
This has been acked by Hans from the V4L driver side, Luis from the
module side, Mauro on the media side, and Christoph said it was the
correct solution, and was tested by the original reporter of the
issue.
It has passed 0-day testing, but has not been in linux-next due to it
only being sent yesterday"
* tag 'driver-core-6.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
media: dvb: symbol fixup for dvb_attach()
Merge tag 'dma-mapping-6.6-2023-09-09' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- move a dma-debug call that prints a message out from a lock that's
causing problems with the lock order in serial drivers (Sergey
Senozhatsky)
- fix the CONFIG_DMA_NUMA_CMA Kconfig entry to have the right
dependency and not default to y (Christoph Hellwig)
- move an ifdef a bit to remove a __maybe_unused that seems to trip up
some sensitivities (Christoph Hellwig)
- revert a bogus check in the CMA allocator (Zhenhua Huang)
* tag 'dma-mapping-6.6-2023-09-09' of git://git.infradead.org/users/hch/dma-mapping:
Revert "dma-contiguous: check for memory region overlap"
dma-pool: remove a __maybe_unused label in atomic_pool_expand
dma-contiguous: fix the Kconfig entry for CONFIG_DMA_NUMA_CMA
dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
Merge tag 'pci-v6.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- Add PCI_DYNAMIC_OF_NODES dependency on OF_IRQ to fix sparc64 build
error (Lizhi Hou)
- After coalescing host bridge resources, free any released resources
to avoid a leak (Ross Lagerwall)
- Revert a quirk that prevented NVIDIA T4 GPUs from using Secondary Bus
Reset. The quirk worked around an issue that we now think is related
to the Root Port, not the GPU (Bjorn Helgaas)
* tag 'pci-v6.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
Revert "PCI: Mark NVIDIA T4 GPUs to avoid bus reset"
PCI: Free released resource after coalescing
PCI: Fix CONFIG_PCI_DYNAMIC_OF_NODES kconfig dependencies
Merge tag 'ntb-6.6' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Link toggling fixes and debugfs error path fixes"
[ And for everybody like me who always have to remind themselves what
the TLA of the day is, and what NTB stands for - it's a PCIe
"Non-Transparent Bridge" thing - Linus ]
* tag 'ntb-6.6' of https://github.com/jonmason/ntb:
ntb: Check tx descriptors outstanding instead of head/tail for tx queue
ntb: Fix calculation ntb_transport_tx_free_entry()
ntb: Drop packets when qp link is down
ntb: Clean up tx tail index on link down
ntb: amd: Drop unnecessary error check for debugfs_create_dir
NTB: ntb_tool: Switch to memdup_user_nul() helper
dtivers: ntb: fix parameter check in perf_setup_dbgfs()
ntb: Remove error checking for debugfs_create_dir()
In commit 9011e49d54dc ("modules: only allow symbol_get of
EXPORT_SYMBOL_GPL modules") the use of symbol_get is properly restricted
to GPL-only marked symbols. This interacts oddly with the DVB logic
which only uses dvb_attach() to load the dvb driver which then uses
symbol_get().
Fix this up by properly marking all of the dvb_attach attach symbols as
EXPORT_SYMBOL_GPL().
Fixes: 9011e49d54dc ("modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules") Cc: stable <stable@kernel.org> Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: linux-media@vger.kernel.org Cc: linux-modules@vger.kernel.org Acked-by: Luis Chamberlain <mcgrof@kernel.org> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Link: https://lore.kernel.org/r/20230908092035.3815268-2-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'xarray-6.6' of git://git.infradead.org/users/willy/xarray
Pull xarray fixes from Matthew Wilcox:
- Fix a bug encountered by people using bittorrent where they'd get
NULL pointer dereferences on page cache lookups when using XFS
- Two documentation fixes
* tag 'xarray-6.6' of git://git.infradead.org/users/willy/xarray:
idr: fix param name in idr_alloc_cyclic() doc
xarray: Document necessary flag in alloc functions
XArray: Do not return sibling entries from xa_load()
- Fix a regression in partition handling for devices not supporting
partitions (Li)
* tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux:
drbd: swap bvec_set_page len and offset
block: fix pin count management when merging same-page segments
null_blk: fix poll request timeout handling
s390/dasd: fix string length handling
block: don't add or resize partition on the disk with GENHD_FL_NO_PART
block: remove the call to file_remove_privs in blkdev_write_iter
blk-throttle: consider 'carryover_ios/bytes' in throtl_trim_slice()
blk-throttle: use calculate_io/bytes_allowed() for throtl_trim_slice()
blk-throttle: fix wrong comparation while 'carryover_ios/bytes' is negative
blk-throttle: print signed value 'carryover_bytes/ios' for user
Merge tag 'io_uring-6.6-2023-09-08' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"A few fixes that should go into the 6.6-rc merge window:
- Fix for a regression this merge window caused by the SQPOLL
affinity patch, where we can race with SQPOLL thread shutdown and
cause an oops when trying to set affinity (Gabriel)
- Fix for a regression this merge window where fdinfo reading with
for a ring setup with IORING_SETUP_NO_SQARRAY will attempt to
deference the non-existing SQ ring array (me)
- Add the patch that allows more finegrained control over who can use
io_uring (Matteo)
- Locking fix for a regression added this merge window for IOPOLL
overflow (Pavel)
- IOPOLL fix for stable, breaking our loop if helper threads are
exiting (Pavel)
Also had a fix for unreaped iopoll requests from io-wq from Ming, but
we found an issue with that and hence it got reverted. Will get this
sorted for a future rc"
* tag 'io_uring-6.6-2023-09-08' of git://git.kernel.dk/linux:
Revert "io_uring: fix IO hang in io_wq_put_and_exit from do_exit()"
io_uring: fix unprotected iopoll overflow
io_uring: break out of iowq iopoll on teardown
io_uring: add a sysctl to disable io_uring system-wide
io_uring/fdinfo: only print ->sq_array[] if it's there
io_uring: fix IO hang in io_wq_put_and_exit from do_exit()
io_uring: Don't set affinity on a dying sqpoll thread
Merge tag 'thermal-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"Eliminate an obsolete thermal zone registration function"
* tag 'thermal-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Drop thermal_zone_device_register()
thermal: Use thermal_tripless_zone_device_register()
thermal: core: Add function for registering tripless thermal zones
thermal: core: Clean up headers of thermal zone registration functions
Merge tag 'pm-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix an Intel RAPL power capping driver regression introduced during
the 6.5 development cycle (Srinivas Pandruvada)"
* tag 'pm-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: intel_rapl: Fix invalid setting of Power Limit 4
Merge tag 'gpio-fixes-for-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a regression in irqchip setup in gpio-zynq
* tag 'gpio-fixes-for-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: zynq: restore zynq_gpio_irq_reqres/zynq_gpio_irq_relres callbacks
d5af729dc207 ("PCI: Mark NVIDIA T4 GPUs to avoid bus reset") avoided
Secondary Bus Reset on the T4 because the reset seemed to not work when the
T4 was directly attached to a Root Port.
But NVIDIA thinks the issue is probably related to some issue with the Root
Port, not with the T4. The T4 provides neither PM nor FLR reset, so
masking bus reset compromises this device for assignment scenarios.
Revert d5af729dc207 as requested by Wu Zongyong. This will leave SBR
broken in the specific configuration Wu tested, as it was in v6.5, so Wu
will debug that further.
Merge tag 'sound-fix-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for 6.6-rc1. All small and easy ones.
- The corrections of the previous PCM iov_iter transitions
- Regression fixes in MIDI 2.0 / USB changes
- Various ASoC codec fixes for Cirrus, Realtek, WCD
- ASoC AMD quirks and ASoC Intel AVS driver workaround"
* tag 'sound-fix-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek - ALC287 I2S speaker platform support
ASoC: amd: yc: Fix a non-functional mic on Lenovo 82TL
ASoC: Intel: avs: Provide support for fallback topology
ALSA: seq: Fix snd_seq_expand_var_event() call to user-space
ALSA: usb-audio: Fix potential memory leaks at error path for UMP open
ALSA: hda/cirrus: Fix broken audio on hardware with two CS42L42 codecs.
ASoC: rt5645: NULL pointer access when removing jack
ASoC: amd: yc: Add DMI entries to support Victus by HP Gaming Laptop 15-fb0xxx (8A3E)
MAINTAINERS: Update the MAINTAINERS enties for TEXAS INSTRUMENTS ASoC DRIVERS
ALSA: sb: Fix wrong argument in commented code
ALSA: pcm: Fix error checks of default read/write copy ops
ASoC: Name iov_iter argument as iterator instead of buffer
ASoC: dmaengine: Drop unused iov_iter for process callback
ALSA: hda/tas2781: Use standard clamp() macro
ASoC: cs35l56: Waiting for firmware to boot must be tolerant of I/O errors
ASoC: dt-bindings: fsl_easrc: Add support for imx8mp-easrc
ASoC: cs42l43: Fix missing error code in cs42l43_codec_probe()
ASoC: cs35l45: Rename DACPCM1 Source control
ASoC: cs35l45: Fix "Dead assigment" warning
ASoC: cs35l45: Add support for Chip ID 0x35A460
...
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main one is a fix for a broken strscpy() conversion that landed in
the merge window and broke early parsing of the kernel command line.
- Fix an incorrect mask in the CXL PMU driver
- Fix a regression in early parsing of the kernel command line
- Fix an IP checksum OoB access reported by syzbot"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: csum: Fix OoB access in IP checksum code for negative lengths
arm64/sysreg: Fix broken strncpy() -> strscpy() conversion
perf: CXL: fix mismatched number of counters mask
Merge tag 'loongarch-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Allow usage of LSX/LASX in the kernel, and use them for
SIMD-optimized RAID5/RAID6 routines
- Add Loongson Binary Translation (LBT) extension support
- Add basic KGDB & KDB support
- Add building with kcov coverage
- Add KFENCE (Kernel Electric-Fence) support
- Add KASAN (Kernel Address Sanitizer) support
- Some bug fixes and other small changes
- Update the default config file
* tag 'loongarch-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: (25 commits)
LoongArch: Update Loongson-3 default config file
LoongArch: Add KASAN (Kernel Address Sanitizer) support
LoongArch: Simplify the processing of jumping new kernel for KASLR
kasan: Add (pmd|pud)_init for LoongArch zero_(pud|p4d)_populate process
kasan: Add __HAVE_ARCH_SHADOW_MAP to support arch specific mapping
LoongArch: Add KFENCE (Kernel Electric-Fence) support
LoongArch: Get partial stack information when providing regs parameter
LoongArch: mm: Add page table mapped mode support for virt_to_page()
kfence: Defer the assignment of the local variable addr
LoongArch: Allow building with kcov coverage
LoongArch: Provide kaslr_offset() to get kernel offset
LoongArch: Add basic KGDB & KDB support
LoongArch: Add Loongson Binary Translation (LBT) extension support
raid6: Add LoongArch SIMD recovery implementation
raid6: Add LoongArch SIMD syndrome calculation
LoongArch: Add SIMD-optimized XOR routines
LoongArch: Allow usage of LSX/LASX in the kernel
LoongArch: Define symbol 'fault' as a local label in fpu.S
LoongArch: Adjust {copy, clear}_user exception handler behavior
LoongArch: Use static defined zero page rather than allocated
...
Merge tag 'landlock-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull landlock updates from Mickaël Salaün:
"One test fix and a __counted_by annotation"
* tag 'landlock-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
selftests/landlock: Fix a resource leak
landlock: Annotate struct landlock_rule with __counted_by
soc: renesas: Kconfig: For ARCH_R9A07G043 select the required configs if dependencies are met
To prevent randconfig build issues when enabling the RZ/Five SoC, consider
selecting specific configurations only when their dependencies are
satisfied.
riscv: Kconfig.errata: Add dependency for RISCV_SBI in ERRATA_ANDES config
Andes errata uses sbi_ecalll() which is only available if RISCV_SBI is
enabled. So add an dependency for RISCV_SBI in ERRATA_ANDES config to
avoid any build failures.
riscv: Kconfig.errata: Drop dependency for MMU in ERRATA_ANDES_CMO config
Now that RISCV_DMA_NONCOHERENT conditionally selects DMA_DIRECT_REMAP
ie only if MMU is enabled, we no longer need the MMU dependency in
ERRATA_ANDES_CMO config.
riscv: Kconfig: Select DMA_DIRECT_REMAP only if MMU is enabled
kernel/dma/mapping.c has its use of pgprot_dmacoherent() inside
an #ifdef CONFIG_MMU block. kernel/dma/pool.c has its use of
pgprot_dmacoherent() inside an #ifdef CONFIG_DMA_DIRECT_REMAP block.
So select DMA_DIRECT_REMAP only if MMU is enabled for RISCV_DMA_NONCOHERENT
config.
Merge patch series "bpf, riscv: use BPF prog pack allocator in BPF JIT"
Puranjay Mohan <puranjay12@gmail.com> says:
Here is some data to prove the V2 fixes the problem:
Without this series:
root@rv-selftester:~/src/kselftest/bpf# time ./test_tag
test_tag: OK (40945 tests)
real 7m47.562s
user 0m24.145s
sys 6m37.064s
With this series applied:
root@rv-selftester:~/src/selftest/bpf# time ./test_tag
test_tag: OK (40945 tests)
real 7m29.472s
user 0m25.865s
sys 6m18.401s
BPF programs currently consume a page each on RISCV. For systems with many BPF
programs, this adds significant pressure to instruction TLB. High iTLB pressure
usually causes slow down for the whole system.
Song Liu introduced the BPF prog pack allocator[1] to mitigate the above issue.
It packs multiple BPF programs into a single huge page. It is currently only
enabled for the x86_64 BPF JIT.
I enabled this allocator on the ARM64 BPF JIT[2]. It is being reviewed now.
This patch series enables the BPF prog pack allocator for the RISCV BPF JIT.
======================================================
Performance Analysis of prog pack allocator on RISCV64
======================================================
To test the performance of the BPF prog pack allocator on RV, a stresser
tool[4] linked below was built. This tool loads 8 BPF programs on the system and
triggers 5 of them in an infinite loop by doing system calls.
The runner script starts 20 instances of the above which loads 8*20=160 BPF
programs on the system, 5*20=100 of which are being constantly triggered.
The script is passed a command which would be run in the above environment.
The script was run with following perf command:
./run.sh "perf stat -a \
-e iTLB-load-misses \
-e dTLB-load-misses \
-e dTLB-store-misses \
-e instructions \
--timeout 60000"
The output of the above command is discussed below before and after enabling the
BPF prog pack allocator.
The tests were run on qemu-system-riscv64 with 8 cpus, 16G memory. The rootfs
was created using Bjorn's riscv-cross-builder[5] docker container linked below.
Results
=======
Before enabling prog pack allocator:
------------------------------------
It was expected that the iTLB-load-misses would decrease as now a single huge
page is used to keep all the BPF programs compared to a single page for each
program earlier.
--------------------------------------------
The improvement in iTLB-load-misses: -30.5 %
--------------------------------------------
I repeated this expriment more than 100 times in different setups and the
improvement was always greater than 30%.
This patch series is boot tested on the Starfive VisionFive 2 board[6].
The performance analysis was not done on the board because it doesn't
expose iTLB-load-misses, etc. The stresser program was run on the board to test
the loading and unloading of BPF programs
* b4-shazam-merge:
bpf, riscv: use prog pack allocator in the BPF JIT
riscv: implement a memset like function for text
riscv: extend patch_text_nosync() for multiple pages
bpf: make bpf_prog_pack allocator portable
The following KASLR implementation allows to randomize the kernel mapping:
- virtually: we expect the bootloader to provide a seed in the device-tree
- physically: only implemented in the EFI stub, it relies on the firmware to
provide a seed using EFI_RNG_PROTOCOL. arm64 has a similar implementation
hence the patch 3 factorizes KASLR related functions for riscv to take
advantage.
The new virtual kernel location is limited by the early page table that only
has one PUD and with the PMD alignment constraint, the kernel can only take
< 512 positions.
* b4-shazam-merge:
riscv: libstub: Implement KASLR by using generic functions
libstub: Fix compilation warning for rv32
arm64: libstub: Move KASLR handling functions to kaslr.c
riscv: Dump out kernel offset information on panic
riscv: Introduce virtual kernel mapping KASLR
non-coherent DMA support for AX45MP
====================================
On the Andes AX45MP core, cache coherency is a specification option so it
may not be supported. In this case DMA will fail. To get around with this
issue this patch series does the below:
1] Andes alternative ports is implemented as errata which checks if the
IOCP is missing and only then applies to CMO errata. One vendor specific
SBI EXT (ANDES_SBI_EXT_IOCP_SW_WORKAROUND) is implemented as part of
errata.
Below are the configs which Andes port provides (and are selected by
RZ/Five):
- ERRATA_ANDES
- ERRATA_ANDES_CMO
OpenSBI patch supporting ANDES_SBI_EXT_IOCP_SW_WORKAROUND SBI is now
part v1.3 release.
2] Andes AX45MP core has a Programmable Physical Memory Attributes (PMA)
block that allows dynamic adjustment of memory attributes in the runtime.
It contains a configurable amount of PMA entries implemented as CSR
registers to control the attributes of memory locations in interest.
OpenSBI configures the PMA regions as required and creates a reserve memory
node and propagates it to the higher boot stack.
Currently OpenSBI (upstream) configures the required PMA region and passes
this a shared DMA pool to Linux.
* b4-shazam-merge:
soc: renesas: Kconfig: Select the required configs for RZ/Five SoC
cache: Add L2 cache management for Andes AX45MP RISC-V core
dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller
riscv: mm: dma-noncoherent: nonstandard cache operations support
riscv: errata: Add Andes alternative ports
riscv: asm: vendorid_list: Add Andes Technology to the vendors list
This patch series is a subset from Arnd's original series [0]. Ive just
picked up the bits required for RISC-V unification of cache flushing.
Remaining patches from the series [0] will be taken care by Arnd soon.
* b4-shazam-merge:
riscv: dma-mapping: switch over to generic implementation
riscv: dma-mapping: skip invalidation before bidirectional DMA
riscv: dma-mapping: only invalidate after DMA, not flush
Merge patch series "RISC-V: Probe for misaligned access speed"
Evan Green <evan@rivosinc.com> says:
The current setting for the hwprobe bit indicating misaligned access
speed is controlled by a vendor-specific feature probe function. This is
essentially a per-SoC table we have to maintain on behalf of each vendor
going forward. Let's convert that instead to something we detect at
runtime.
We have two assembly routines at the heart of our probe: one that
does a bunch of word-sized accesses (without aligning its input buffer),
and the other that does byte accesses. If we can move a larger number of
bytes using misaligned word accesses than we can with the same amount of
time doing byte accesses, then we can declare misaligned accesses as
"fast".
The tradeoff of reducing this maintenance burden is boot time. We spend
4-6 jiffies per core doing this measurement (0-2 on jiffie edge
alignment, and 4 on measurement). The timing loop was based on
raid6_choose_gen(), which uses (16+1)*N jiffies (where N is the number
of algorithms). By taking only the fastest iteration out of all
attempts for use in the comparison, variance between runs is very low.
On my THead C906, it looks like this:
[ 0.047563] cpu0: Ratio of byte access time to unaligned word access is 4.34, unaligned accesses are fast
Several others have chimed in with results on slow machines with the
older algorithm, which took all runs into account, including noise like
interrupts. Even with this variation, results indicate that in all cases
(fast, slow, and emulated) the measured numbers are nowhere near each
other (always multiple factors away).
The Commit broke the CMA region creation through DT on arm64,
as showed below logs with "memblock=debug":
[ 0.000000] memblock_phys_alloc_range: 41943040 bytes align=0x200000
from=0x0000000000000000 max_addr=0x00000000ffffffff
early_init_dt_alloc_reserved_memory_arch+0x34/0xa0
[ 0.000000] memblock_reserve: [0x00000000fd600000-0x00000000ffdfffff]
memblock_alloc_range_nid+0xc0/0x19c
[ 0.000000] Reserved memory: overlap with other memblock reserved region
>From call flow, region we defined in DT was always reserved before entering
into rmem_cma_setup. Also, rmem_cma_setup has one routine cma_init_reserved_mem
to ensure the region was reserved. Checking the region not reserved here seems
not correct.
Merge tag 'drm-next-2023-09-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular rounds of rc1 fixes, a large bunch for amdgpu since it's three
weeks in one go, one i915, one nouveau and one ivpu.
I think there might be a few more fixes in misc that I haven't pulled
in yet, but we should get them all for rc2.
amdgpu:
- Display replay fixes
- Fixes for headless boards
- Fix documentation breakage
- RAS fixes
- Handle newer IP discovery tables
- SMU 13.0.6 fixes
- SR-IOV fixes
- Display vstartup fixes
- NBIO 7.9 fixes
- Display scaling mode fixes
- Debugfs power reporting fix
- GC 9.4.3 fixes
- Dirty framebuffer fixes for fbcon
- eDP fixes
- DCN 3.1.5 fix
- Display ODM fixes
- GPU core dump fix
- Re-enable zops property now that IGT test is fixed
- Fix possible UAF in CS code
- Cursor degamma fix
i915:
- Mark requests for GuC virtual engines to avoid use-after-free
nouveau:
- Fix fence state in nouveau_fence_emit()
ivpu:
- replace strncpy"
* tag 'drm-next-2023-09-08' of git://anongit.freedesktop.org/drm/drm: (51 commits)
drm/amdgpu: Restrict bootloader wait to SMUv13.0.6
drm/amd/display: prevent potential division by zero errors
drm/amd/display: enable cursor degamma for DCN3+ DRM legacy gamma
drm/amd/display: limit the v_startup workaround to ASICs older than DCN3.1
Revert "drm/amd/display: Remove v_startup workaround for dcn3+"
drm/amdgpu: fix amdgpu_cs_p1_user_fence
Revert "Revert "drm/amd/display: Implement zpos property""
drm/amdkfd: Add missing gfx11 MQD manager callbacks
drm/amdgpu: Free ras cmd input buffer properly
drm/amdgpu: Hide xcp partition sysfs under SRIOV
drm/amdgpu: use read-modify-write mode for gfx v9_4_3 SQ setting
drm/amdkfd: use mask to get v9 interrupt sq data bits correctly
drm/amdgpu: Allocate coredump memory in a nonblocking way
drm/amdgpu: Support query ecc cap for aqua_vanjaram
drm/amdgpu: Add umc_info v4_0 structure
drm/amd/display: always switch off ODM before committing more streams
drm/amd/display: Remove wait while locked
drm/amd/display: update blank state on ODM changes
drm/amd/display: Add smu write msg id fail retry process
drm/amdgpu: Add SMU v13.0.6 default reset methods
...
- deal with integer overflows in kmalloc_reserve()
- use sk_forward_alloc_get() in sk_get_meminfo()
- bpf_sk_storage: fix the missing uncharge in sk_omem_alloc
- fib: avoid warn splat in flow dissector after packet mangling
- skb_segment: call zero copy functions before using skbuff frags
- eth: sfc: check for zero length in EF10 RX prefix
Previous releases - always broken:
- af_unix: fix msg_controllen test in scm_pidfd_recv() for
MSG_CMSG_COMPAT
- xsk: fix xsk_build_skb() dereferencing possible ERR_PTR()
- netfilter:
- nft_exthdr: fix non-linear header modification
- xt_u32, xt_sctp: validate user space input
- nftables: exthdr: fix 4-byte stack OOB write
- nfnetlink_osf: avoid OOB read
- one more fix for the garbage collection work from last release
- igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
- bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t
- handshake: fix null-deref in handshake_nl_done_doit()
- ip: ignore dst hint for multipath routes to ensure packets are
hashed across the nexthops
- phy: micrel:
- correct bit assignments for cable test errata
- disable EEE according to the KSZ9477 errata
Merge tag 'pwm/for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various cleanups and fixes across the board"
* tag 'pwm/for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (31 commits)
pwm: lpc32xx: Remove handling of PWM channels
pwm: atmel: Simplify using devm functions
dt-bindings: pwm: brcm,kona-pwm: convert to YAML
pwm: stmpe: Handle errors when disabling the signal
pwm: stm32: Simplify using devm_pwmchip_add()
pwm: stm32: Don't modify HW state in .remove() callback
pwm: Fix order of freeing resources in pwmchip_remove()
pwm: ntxec: Use device_set_of_node_from_dev()
pwm: ntxec: Drop a write-only variable from driver data
pwm: pxa: Don't reimplement of_device_get_match_data()
pwm: lpc18xx-sct: Simplify using devm_clk_get_enabled()
pwm: atmel-tcb: Don't track polarity in driver data
pwm: atmel-tcb: Unroll atmel_tcb_pwm_set_polarity() into only caller
pwm: atmel-tcb: Put per-channel data into driver data
pwm: atmel-tcb: Fix resource freeing in error path and remove
pwm: atmel-tcb: Harmonize resource allocation order
pwm: Drop unused #include <linux/radix-tree.h>
pwm: rz-mtu3: Fix build warning 'num_channel_ios' not described
pwm: Remove outdated documentation for pwmchip_remove()
pwm: atmel: Enable clk when pwm already enabled in bootloader
...
Merge tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support"
* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...
Merge tag 'i3c/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Core:
- Fix SETDASA when static and dynamic adress are equal
- Fix cmd_v1 DAA exit criteria
Drivers:
- svc: allow probing without any device"
* tag 'i3c/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix probe failure when no i3c device exist
i3c: master: Fix SETDASA process
dt-bindings: i3c: Fix description for assigned-address
i3c: master: svc: Describe member 'saved_regs'
i3c: master: svc: Do not check for 0 return after calling platform_get_irq()
i3c/master: cmd_v1: Fix the exit criteria for the daa procedure
i3c: Explicitly include correct DT includes
Merge tag 'regulator-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes that came in during the merge window, both driver
specific - one for a bug that came up in testing, one for a bug due
to a misreading of the datasheet"
* tag 'regulator-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6594-regulator: Fix random kernel crash
regulator: tps6287x: Fix n_voltages
Merge tag 'spi-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes for the sun6i driver. The patch to reduce DMA RX to
single byte width all the time is *hopefully* excessively cautious but
it's unclear which SoCs are affected so the fix just covers everything
for safety"
* tag 'spi-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
spi: sun6i: reduce DMA RX transfer width to single byte
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Clean up vCPU targets, always returning generic v8 as the preferred
target
- Trap forwarding infrastructure for nested virtualization (used for
traps that are taken from an L2 guest and are needed by the L1
hypervisor)
- FEAT_TLBIRANGE support to only invalidate specific ranges of
addresses when collapsing a table PTE to a block PTE. This avoids
that the guest refills the TLBs again for addresses that aren't
covered by the table PTE.
- Fix vPMU issues related to handling of PMUver.
- Don't unnecessary align non-stack allocations in the EL2 VA space
- Drop HCR_VIRT_EXCP_MASK, which was never used...
- Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu
parameter instead
- Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
- Remove prototypes without implementations
RISC-V:
- Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
- Added ONE_REG interface for SATP mode
- Added ONE_REG interface to enable/disable multiple ISA extensions
- Improved error codes returned by ONE_REG interfaces
- Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
- Guest debug fixes (Ilya)
x86:
- Clean up KVM's handling of Intel architectural events
- Intel bugfixes
- Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use
debug registers and generate/handle #DBs
- Clean up LBR virtualization code
- Fix a bug where KVM fails to set the target pCPU during an IRTE
update
- Fix fatal bugs in SEV-ES intrahost migration
- Fix a bug where the recent (architecturally correct) change to
reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to
skip it)
- Retry APIC map recalculation if a vCPU is added/enabled
- Overhaul emergency reboot code to bring SVM up to par with VMX, tie
the "emergency disabling" behavior to KVM actually being loaded,
and move all of the logic within KVM
- Fix user triggerable WARNs in SVM where KVM incorrectly assumes the
TSC ratio MSR cannot diverge from the default when TSC scaling is
disabled up related code
- Add a framework to allow "caching" feature flags so that KVM can
check if the guest can use a feature without needing to search
guest CPUID
- Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
- Fix KVM's handling of !visible guest roots to avoid premature
triple fault injection
- Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the
API surface that is needed by external users (currently only
KVMGT), and fix a variety of issues in the process
Generic:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier
events to pass action specific data without needing to constantly
update the main handlers.
- Drop unused function declarations
Selftests:
- Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
- Add support for printf() in guest code and covert all guest asserts
to use printf-based reporting
- Clean up the PMU event filter test and add new testcases
- Include x86 selftests in the KVM x86 MAINTAINERS entry"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits)
KVM: x86/mmu: Include mmu.h in spte.h
KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots
KVM: x86/mmu: Disallow guest from using !visible slots for page tables
KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page
KVM: x86/mmu: Harden new PGD against roots without shadow pages
KVM: x86/mmu: Add helper to convert root hpa to shadow page
drm/i915/gvt: Drop final dependencies on KVM internal details
KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers
KVM: x86/mmu: Drop @slot param from exported/external page-track APIs
KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled
KVM: x86/mmu: Assert that correct locks are held for page write-tracking
KVM: x86/mmu: Rename page-track APIs to reflect the new reality
KVM: x86/mmu: Drop infrastructure for multiple page-track modes
KVM: x86/mmu: Use page-track notifiers iff there are external users
KVM: x86/mmu: Move KVM-only page-track declarations to internal header
KVM: x86: Remove the unused page-track hook track_flush_slot()
drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region()
KVM: x86: Add a new page-track hook to handle memslot deletion
drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot
KVM: x86: Reject memslot MOVE operations if KVMGT is attached
...
Vladimir Oltean [Wed, 6 Sep 2023 14:16:09 +0000 (17:16 +0300)]
net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()
enetc_psi_create() returns an ERR_PTR() or a valid station interface
pointer, but checking for the non-NULL quality of the return code blurs
that difference away. So if enetc_psi_create() fails, we call
enetc_psi_destroy() when we shouldn't. This will likely result in
crashes, since enetc_psi_create() cleans up everything after itself when
it returns an ERR_PTR().
Fixes: f0168042a212 ("net: enetc: reimplement RFS/RSS memory clearing as PCI quirk") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/netdev/582183ef-e03b-402b-8e2d-6d9bb3c83bd9@moroto.mountain/ Suggested-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230906141609.247579-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- A couple of virtual vs physical address confusion fixes
- Rework locking in dcssblk driver to address a lockdep warning
- Remove support for "noexec" kernel command line option since there is
no use case where it would make sense
- Simplify kernel mapping setup and get rid of quite a bit of code
- Add architecture specific __set_memory_yy() functions which allow us
to modify kernel mappings. Unlike the set_memory_xx() variants they
take void pointer start and end parameters, which allows using them
without the usual casts, and also to use them on areas larger than
8TB.
Note that the set_memory_xx() family comes with an int num_pages
parameter which overflows with 8TB. This could be addressed by
changing the num_pages parameter to unsigned long, however requires
to change all architectures, since the module code expects an int
parameter (see module_set_memory()).
This was indeed an issue since for debug_pagealloc() we call
set_memory_4k() on the whole identity mapping. Therefore address this
for now with the __set_memory_yy() variant, and address common code
later
- Use dev_set_name() and also fix memory leak in zcrypt driver error
handling
- Remove unused lsi_mask from airq_struct
- Add warning for invalid kernel mapping requests
* tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vmem: do not silently ignore mapping limit
s390/zcrypt: utilize dev_set_name() ability to use a formatted string
s390/zcrypt: don't leak memory if dev_set_name() fails
s390/mm: fix MAX_DMA_ADDRESS physical vs virtual confusion
s390/airq: remove lsi_mask from airq_struct
s390/mm: use __set_memory() variants where useful
s390/set_memory: add __set_memory() variant
s390/set_memory: generate all set_memory() functions
s390/mm: improve description of mapping permissions of prefix pages
s390/amode31: change type of __samode31, __eamode31, etc
s390/mm: simplify kernel mapping setup
s390: remove "noexec" option
s390/vmem: fix virtual vs physical address confusion
s390/dcssblk: fix lockdep warning
s390/monreader: fix virtual vs physical address confusion
Merge tag 'xtensa-20230905' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa updates from Max Filippov:
- enable MTD XIP support
- fix base address of the xtensa perf module in newer hardware
* tag 'xtensa-20230905' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: add XIP-aware MTD support
xtensa: PMU: fix base address for the newer hardware
Recently we moved most cleanup from ntfs_put_super() into
ntfs3_kill_sb() as part of a bigger cleanup. This accidently also moved
dropping inode references stashed in ntfs3's sb->s_fs_info from
@sb->put_super() to @sb->kill_sb(). But generic_shutdown_super()
verifies that there are no busy inodes past sb->put_super(). Fix this
and disentangle dropping inode references from freeing @sb->s_fs_info.
Fixes: a4f64a300a29 ("ntfs3: free the sbi in ->kill_sb") # mainline only Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vfs: mostly undo glibc turning 'fstat()' into 'fstatat(AT_EMPTY_PATH)'
Mateusz reports that glibc turns 'fstat()' calls into 'fstatat()', and
that seems to have been going on for quite a long time due to glibc
having tried to simplify its stat logic into just one point.
This turns out to cause completely unnecessary overhead, where we then
go off and allocate the kernel side pathname, and actually look up the
empty path. Sure, our path lookup is quite optimized, but it still
causes a fair bit of allocation overhead and a couple of completely
unnecessary rounds of lockref accesses etc.
This is all hopefully getting fixed in user space, and there is a patch
floating around for just having glibc use the native fstat() system
call. But even with the current situation we can at least improve on
things by catching the situation and short-circuiting it.
Note that this is still measurably slower than just a plain 'fstat()',
since just checking that the filename is actually empty is somewhat
expensive due to inevitable user space access overhead from the kernel
(ie verifying pointers, and SMAP on x86). But it's still quite a bit
faster than actually looking up the path for real.
To quote numers from Mateusz:
"Sapphire Rapids, will-it-scale, ops/s
where that 'stock fstat' is the glibc translation of fstat into
fstatat() with an empty path, the 'patched fstat' is with this short
circuiting of the path lookup, and the 'real fstat' is the actual native
fstat() system call with none of this overhead.
This commit cancels all requests with io-wq, not just the ones from the
originating task. This breaks use cases that have thread pools, or just
multiple tasks issuing requests on the same ring. The liburing
regression test for this also shows that problem:
$ test/thread-exit.t
cqe->res=-125, Expected 512
where an IO thread gets its request canceled rather than complete
successfully.
Pavel Begunkov [Thu, 7 Sep 2023 12:50:07 +0000 (13:50 +0100)]
io_uring: break out of iowq iopoll on teardown
io-wq will retry iopoll even when it failed with -EAGAIN. If that
races with task exit, which sets TIF_NOTIFY_SIGNAL for all its workers,
such workers might potentially infinitely spin retrying iopoll again and
again and each time failing on some allocation / waiting / etc. Don't
keep spinning if io-wq is dying.
Fixes: 561fb04a6a225 ("io_uring: replace workqueue usage with io-wq") Cc: stable@vger.kernel.org Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paolo Abeni [Thu, 7 Sep 2023 09:47:15 +0000 (11:47 +0200)]
Merge tag 'nf-23-09-06' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
netfilter updates for net
This PR contains nf_tables updates for your *net* tree.
This time almost all fixes are for old bugs:
First patch fixes a 4-byte stack OOB write, from myself.
This was broken ever since nftables was switches from 128 to 32bit
register addressing in v4.1.
2nd patch fixes an out-of-bounds read.
This has been broken ever since xt_osf got added in 2.6.31, the bug
was then just moved around during refactoring, from Wander Lairson Costa.
3rd patch adds a missing enum description, from Phil Sutter.
4th patch fixes a UaF inftables that occurs when userspace adds
elements with a timeout so small that expiration happens while the
transaction is still in progress. Fix from Pablo Neira Ayuso.
Patch 5 fixes a memory out of bounds access, this was
broken since v4.20. Patch from Kyle Zeng and Jozsef Kadlecsik.
Patch 6 fixes another bogus memory access when building audit
record. Bug added in the previous pull request, fix from Pablo.
netfilter pull request 2023-09-06
* tag 'nf-23-09-06' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: Unbreak audit log reset
netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c
netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID
netfilter: nfnetlink_osf: avoid OOB read
netfilter: nftables: exthdr: fix 4-byte stack OOB write
====================
Will Deacon [Thu, 7 Sep 2023 08:54:11 +0000 (09:54 +0100)]
arm64: csum: Fix OoB access in IP checksum code for negative lengths
Although commit c2c24edb1d9c ("arm64: csum: Fix pathological zero-length
calls") added an early return for zero-length input, syzkaller has
popped up with an example of a _negative_ length which causes an
undefined shift and an out-of-bounds read:
Jie Wang [Wed, 6 Sep 2023 07:20:18 +0000 (15:20 +0800)]
net: hns3: remove GSO partial feature bit
HNS3 NIC does not support GSO partial packets segmentation. Actually tunnel
packets for example NvGRE packets segment offload and checksum offload is
already supported. There is no need to keep gso partial feature bit. So
this patch removes it.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
We hope that tc qdisc and dcb ets commands can not be used crosswise.
If we want to use any of the commands to configure tc,
We must use the other command to clear the existing configuration.
However, when we configure a single tc with tc qdisc,
we can still configure it with dcb ets.
Because we use mqprio_active as the tag of tc qdisc configuration,
but with dcb ets, we do not check mqprio_active.
This patch fix this issue by check mqprio_active before
executing the dcb ets command. and add dcb_ets_active to
replace HCLGE_FLAG_DCB_ENABLE and HCLGE_FLAG_MQPRIO_ENABLE
at the hclge layer,
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
req1->tcam_data is defined as "u8 tcam_data[8]", and we convert it as
(u32 *) without considerring byte order conversion,
it may result in printing wrong data for tcam_data.
Currently, the driver knocks the ring doorbell before updating
the ring->last_to_use in tx flow. if the hardware transmiting
packet and napi poll scheduling are fast enough, it may get
the old ring->last_to_use in drivers' napi poll.
In this case, the driver will think the tx is not completed, and
return directly without clear the flag __QUEUE_STATE_STACK_XOFF,
which may cause tx timeout.
Kailang Yang [Wed, 6 Sep 2023 08:50:41 +0000 (16:50 +0800)]
ALSA: hda/realtek - ALC287 I2S speaker platform support
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing. So,it needs to
swap DAC.
Steve French [Fri, 1 Sep 2023 06:29:17 +0000 (01:29 -0500)]
smb3: add trace point for queryfs (statfs)
In debugging a recent performance problem with statfs, it would have
been helpful to be able to trace the smb3 query fs info request
more narrowly. Add a trace point "smb3_qfs_done"
1, Enable LSX and LASX.
2, Enable KASLR (CONFIG_RANDOMIZE_BASE).
3, Enable jump label (patching mechanism for static key).
4, Enable LoongArch CRC32(c) Acceleration.
5, Enable Loongson-specific drivers: I2C/RTC/DRM/SOC/CLK/PINCTRL/GPIO/SPI.
6, Enable EXFAT/NTFS3/JFS/GFS2/OCFS2/UBIFS/EROFS/CEPH file systems.
7, Enable WangXun NGBE/TXGBE NIC drivers.
8, Enable some IPVS options.
9, Remove CONFIG_SYSFS_DEPRECATED since it is removed in Kconfig.
10, Remove CONFIG_IP_NF_TARGET_CLUSTERIP since it is removed in Kconfig.
11, Remove CONFIG_NFT_OBJREF since it is removed in Kconfig.
12, Remove CONFIG_R8188EU since it is replaced by CONFIG_RTL8XXXU.
net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Hamza Mahfooz [Tue, 5 Sep 2023 17:27:22 +0000 (13:27 -0400)]
drm/amd/display: prevent potential division by zero errors
There are two places in apply_below_the_range() where it's possible for
a divide by zero error to occur. So, to fix this make sure the divisor
is non-zero before attempting the computation in both cases.
Melissa Wen [Thu, 31 Aug 2023 16:12:28 +0000 (15:12 -0100)]
drm/amd/display: enable cursor degamma for DCN3+ DRM legacy gamma
For DRM legacy gamma, AMD display manager applies implicit sRGB degamma
using a pre-defined sRGB transfer function. It works fine for DCN2
family where degamma ROM and custom curves go to the same color block.
But, on DCN3+, degamma is split into two blocks: degamma ROM for
pre-defined TFs and `gamma correction` for user/custom curves and
degamma ROM settings doesn't apply to cursor plane. To get DRM legacy
gamma working as expected, enable cursor degamma ROM for implict sRGB
degamma on HW with this configuration.
Cc: stable@vger.kernel.org Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2803 Fixes: 96b020e2163f ("drm/amd/display: check attr flag before set cursor degamma on DCN3+") Signed-off-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / mirror_ubuntu-kernels.git / log