drm/i915: Use atomic state to obtain load detection crtc, v3.
Instead of restoring dpms and a flag for whether a temp fb is allocated duplicate
an atomic state before the new state is committed, and commit it the old state
in intel_release_load_detect_pipe.
Changes since v1:
- Use a real atomic state. (Ville)
Changes since v2:
- Do not preserve shared_dpll any more, no need to do so. (Ville)
Rodrigo Vivi [Fri, 12 Feb 2016 12:08:13 +0000 (04:08 -0800)]
drm/i915: Enable PSR by default on Haswell and Broadwell.
With a reliable frontbuffer tracking and all instability corner cases
on Haswell and Broadwell solved let's re-enabled PSR by default on
these platforms.
In case a new issue is found and PSR is the main suspect, please check
if i915.enable_psr=0 really makes your problem go away. If this is the case
PSR is the culprit so after that please check if i915.enable_psr=2
or i915.enable_psr=3 solves your issue and please let us know.
There are many panels out there and not all implementations apparently
work as we would expect.
In case you needed to force it on standby or disabled or in case of any
PSR related bug please report it at bugs.freedesktop.org.
In a bugzilla entry for PSR is desirable:
- dmesg (drm.debug=0xe)
- output of /sys/kernel/debug/dri/0/i915_edp_psr_status
- Platform information. Vendor, model, id, pci id.
- Graphical environment: Gnome, KDE, openbox, etc...
- Details how to reproduce.
- Also good if you could run PSR test cases of Intel-gpu-tools
- Please mention if forcing main link standby or main link off helps you.
There are Intel-gpu-tools test cases that can be helpful to
determine if PSR is working as expected:
kms_psr_sink_crc and kms_psr_frontbuffer_tracking.
Rodrigo Vivi [Fri, 12 Feb 2016 12:08:12 +0000 (04:08 -0800)]
drm/i915: Enable PSR by default on Valleyview and Cherryview.
With a reliable frontbuffer tracking and all instability corner cases
solved for this platform let's re-enabled PSR by default.
In case a new issue is found and PSR is the main suspect, please check
if i915.enable_psr=0 really makes your problem go away,
please report it at bugs.freedesktop.org.
In a bugzilla entry for PSR is desirable:
- dmesg (drm.debug=0xe)
- output of /sys/kernel/debug/dri/0/i915_edp_psr_status
- Platform information. Vendor, model, id, pci id.
- Graphical environment: Gnome, KDE, openbox, etc...
- Details how to reproduce.
- Also good if you could run PSR test cases of Intel-gpu-tools
- Please mention if forcing main link standby or main link off helps you.
There are Intel-gpu-tools test cases that can be helpful to
determine if PSR is working as expected:
kms_psr_sink_crc and kms_psr_frontbuffer_tracking.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 12 Feb 2016 12:08:11 +0000 (04:08 -0800)]
drm/i915: Change i915.enable_psr parameter to use per platform default.
This will give us flexibility to enable PSR by default independently so
issues and corner cases in one platform won't affect others were we have
it working properly.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Fri, 12 Feb 2016 16:55:21 +0000 (18:55 +0200)]
drm/i915/lvds: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:20 +0000 (18:55 +0200)]
drm/i915/hdmi: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:19 +0000 (18:55 +0200)]
drm/i915/dsi: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:18 +0000 (18:55 +0200)]
drm/i915/dp: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:17 +0000 (18:55 +0200)]
drm/i915: Ensure the HW is powered when accessing the CRC HW block
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
While at it also add the missing reference around the HW access in
i915_interrupt_info().
v2:
- update the commit message mentioning that this also fixes the
HW access in the interrupt info debugfs entry (Daniel)
Imre Deak [Fri, 12 Feb 2016 16:55:16 +0000 (18:55 +0200)]
drm/i915/ddi: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:15 +0000 (18:55 +0200)]
drm/i915/crt: Ensure the HW is powered during HW state readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:14 +0000 (18:55 +0200)]
drm/i915: Ensure the HW is powered during HW access in assert_pipe
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:13 +0000 (18:55 +0200)]
drm/i915: Ensure the HW is powered when disabling VGA
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:12 +0000 (18:55 +0200)]
drm/i915/ibx: Ensure the HW is powered during PLL HW readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Fri, 12 Feb 2016 16:55:11 +0000 (18:55 +0200)]
drm/i915: Ensure the HW is powered during display pipe HW readout
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Imre Deak [Wed, 17 Feb 2016 12:17:42 +0000 (14:17 +0200)]
drm/i915: Add helper to get a display power ref if it was already enabled
We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.
Kudos to Ville and Joonas for the ideas of this new interface.
v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled
CC: Mika Kuoppala <mika.kuoppala@intel.com> CC: Chris Wilson <chris@chris-wilson.co.uk> CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> CC: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com
Chris Wilson [Mon, 11 Jan 2016 09:16:14 +0000 (09:16 +0000)]
drm/i915: Add an optional selection from i915 of CONFIG_MMU_NOTIFIER
userptr requires mmu-notifier for full unprivileged support. Most
systems have mmu-notifier support already enabled as a requirement for
virtualisation support, but we should make the option for i915 to take
advantage of mmu-notifiers explicit (and enable by default so that
regular userspace can take advantage of passing client memory to the
GPU.)
Ben Widawsky [Tue, 9 Feb 2016 19:44:12 +0000 (11:44 -0800)]
drm/i915: Check for get_pages instead of shmem (filp)
This behavior of checking for a shmem backed GEM object was introduced here:
commit 4c914c0c7c787b8f730128a8cdcca9c50b0784ab
Author: Brad Volkin <bradley.d.volkin@intel.com>
Date: Tue Feb 18 10:15:45 2014 -0800
drm/i915: Refactor shmem pread setup
It is possible for an object to not be a shmem backed GEM object (for example
userptr objects). An example of how we hit this failure can be found through
copy_batch() in the command parser because we allocate a userptr object for the
batch which contains privileged instructions. Userptr calls
drm_gem_private_object_init() which explicitly sets the filp to none.
NOTE: I manually retyped this from a test machine. So I haven't even compiled
this exact patch.
v2: Use same logic as from a2a4f916c2f (Kristian, Dave Gordon)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Kristian Høgsberg <krh@bitplanet.net> Cc: Dave Gordon <david.s.gordon@intel.com> Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com> Tested-by: Jordan Justen <jordan.l.justen@intel.com> (v1) Reviewed-by: Jordan Justen <jordan.l.justen@intel.com> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1455047053-2644-1-git-send-email-benjamin.widawsky@intel.com
Ville Syrjälä [Thu, 11 Feb 2016 14:44:28 +0000 (16:44 +0200)]
drm/i915: Add missing 'else' to intel_digital_port_connected()
intel_digital_port_connected() lacks one 'else'. There's no
actual harm in not having it since each branch has an unconditional
return, so it can't accidentally end up in taking two branches instead
of just the one. But let's be consistent and add the 'else' anyway.
Ville Syrjälä [Wed, 10 Feb 2016 17:59:05 +0000 (19:59 +0200)]
drm/i915: Fix hpd live status bits for g4x
Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.
So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.
So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.
Tvrtko Ursulin [Thu, 11 Feb 2016 10:27:32 +0000 (10:27 +0000)]
drm/i915/ilk: Move register read under spinlock
Code does read-modify-write but the read was outside the lock.
It is fine since the caller holds struct mutex, but if we
correct this we open up the opportunity for decreasing the
mutex duration time since the call to ironlake_enable_drps
does not need it any longer since it is covered by the
mchdev_lock lock.
Tvrtko Ursulin [Thu, 11 Feb 2016 10:27:30 +0000 (10:27 +0000)]
drm/i915: Fix struct mutex vs. RPS lock inversion
RPS lock must be taken before the struct_mutex to avoid
locking inversion. So stop grabbing it for the whole
powersave initialization and instead only take it during
the sections which need it.
Also, struct_mutex is not needed any more since dedicated
RPS lock was added in:
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
Based on prototype patch by Chris Wilson and a subsequent
mailing list discussion involving Ville, Imre, Chris and
Daniel.
v2: More details in the commit.
v3: Use drm_gem_object_unreference_unlocked. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tvrtko Ursulin [Thu, 11 Feb 2016 10:27:29 +0000 (10:27 +0000)]
drm/i915: GEM operations need to be done under the big lock
VMA creation and GEM list management need the big lock.
v2:
Mutex unlock ended on the wrong path somehow. (0-day, Julia Lawall)
Not to mention drm_gem_object_unreference was there in existing
code with no mutex held.
v3:
Some callers of i915_gem_object_create_stolen_for_preallocated
already hold the lock so move the mutex into the other caller
as well.
v4:
Changed to lockdep_assert_held. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: Clear shared dpll based on old state, v2.
Atomic resume was preserving the dpll state because it was required
for clearing pll state correctly. If we look at the old_crtc_state
for pll to clear this is not needed and the hack can be removed.
Changes since v1:
- Rename dpll variable to old_dpll. (Ville)
Chris retracted his reviewed-by (which I failed to notice) and somehow
it blows up (I did it again!) as reported by Mika with the below
backtrace on module reload:
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Gordon <david.s.gordon@intel.com> Cc: Nick Hoath <nicholas.hoath@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Abhay Kumar [Sat, 23 Jan 2016 01:39:04 +0000 (17:39 -0800)]
drm/i915: edp resume/On time optimization.
Make resume/on codepath not to wait for panel_power_cycle_delay(t11_t12)
if this time is already spent in suspend/poweron time.
v2: Use CLOCK_BOOTTIME and remove jiffies for panel power cycle
delay calculation(Ville).
v3: Addressed below comments
1. Tracking time from where last powercycle is initiated.
2. Used ktime_get_bootime() wrapper for boottime clock.
3. Used ktime_ms_delta() to get time difference.
v4: Updated v3 change log in detail.
v5: Removed static from panel_power_on_time(Stéphane).
Arnd Bergmann [Thu, 11 Feb 2016 09:10:00 +0000 (10:10 +0100)]
drm/msm: remove unused variable
After the drm_device_is_unplugged() was removed, the 'dev' variable is now
unused, and we get a warning for that:
drivers/gpu/drm/msm/msm_fbdev.c: In function 'msm_fbdev_mmap':
drivers/gpu/drm/msm/msm_fbdev.c:65:21: error: unused variable 'dev' [-Werror=unused-variable]
With this there's no longer the problem that 2 drivers (fake agp
driver and the drm/i915 driver) fight over the same piece, which fixes
apparent dma leaks detected by CONFIG_DMA_API_DEBUG.
Note that the leak isn't real since intel-gtt refcounts and will tear
down eventually. But the debug code assumes that when the i915 driver
unbinds from the pci device everything should be gone. Which isn't the
case if we have intel-agp enabled - userspace might need it. But by
ditching this intel-gtt setup and teardown is completely tied to the
livetime of the "real" driver.
While at it untangle the init ordering a bit - the fake agp wouldn't
be initialized correctly if i915.ko loads first. Which isn't a problem
since when i915 loads in kms mode you won't need the fake agp support
needed by the ums driver ...
Mika Kahola [Tue, 2 Feb 2016 13:16:43 +0000 (15:16 +0200)]
drm/i915: TV pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
Mika Kahola [Tue, 2 Feb 2016 13:16:42 +0000 (15:16 +0200)]
drm/i915: CRT pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
Mika Kahola [Tue, 2 Feb 2016 13:16:41 +0000 (15:16 +0200)]
drm/i915: SDVO pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
Mika Kahola [Tue, 2 Feb 2016 13:16:40 +0000 (15:16 +0200)]
drm/i915: DisplayPort-MST pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
Mika Kahola [Tue, 2 Feb 2016 13:16:39 +0000 (15:16 +0200)]
drm/i915: HDMI pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to HDMI.
V2:
- removed computation for max dot clock
V3:
- cleanup by removing unnecessary lines
V4:
- max_pixclk variable renamed as max_dotclk
- check for stereo mode added
Mika Kahola [Tue, 2 Feb 2016 13:16:38 +0000 (15:16 +0200)]
drm/i915: DisplayPort pixel clock check
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
Lukas Wunner [Wed, 10 Feb 2016 13:17:41 +0000 (14:17 +0100)]
apple-gmux: Fix build breakage if !CONFIG_ACPI
The DRM drivers i915, nouveau and radeon may be compiled with
CONFIG_ACPI not set, in which case acpi_dev_present() is undefined.
Add a no-op stub for apple_gmux_present() which is used if
CONFIG_APPLE_GMUX is not enabled to avoid build breakage.
(CONFIG_APPLE_GMUX depends on CONFIG_ACPI.)
drm/i915: check that rpm ref is held when accessing ringbuf in stolen mem
While running some tests on the scheduler patches with rpm enabled I
came across a corruption in the ringbuffer, which was root-caused to
the GPU being suspended while commands were being emitted to the
ringbuffer. The access to memory was failing because the GPU needs to
be awake when accessing stolen memory (where my ringbuffer was located).
Since we have this constraint it looks like a sensible idea to check
that we hold a refcount when we access the rungbuffer.
v2: move the check from ring_begin to ringbuffer iomap time (Chris)
v3: update comment (Chris)
Daniel Vetter [Wed, 27 Jan 2016 13:37:59 +0000 (14:37 +0100)]
drm/i915: Stop depending upon CONFIG_AGP_INTEL
The AGP_INTEL driver provides an interface for very old userspace to
control the GART (though the GART itself was only ever emulated on Intel
systems). The pci bridge discovery code is also used by the i915.ko
driver to set up the GTT on old systems, but it does not require the
old userspace interface. When i915.ko selects the old interface, it
binds another user to the core GTT routines, and in particular creates a
second reference to the scratch pages allocated. This hinders resource
leak debugging for when we unload i915.ko as we want to assert that all
DMA pages have been released, but we appear to leak because of the
secondary interface which persists after i915.ko unloads.
All i915.ko users do not require the old /dev/agpgart interface so stop
selecting it and simplify our debugging by dropping the historical
baggage.
Note that by selecting AGP=n it was already possible to unselect
AGP_INTEL. But since we've dropped support for any of the AGP stuff
long ago there's really no point for this any more.
Also note that we still need INTEL_GTT, which is the underlying,
shared, driver for the graphics GART on gen1-5.
v2: Entirely new commit message (Chris, Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1453901881-26425-2-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter [Wed, 27 Jan 2016 13:37:58 +0000 (14:37 +0100)]
agp/intel-gtt: Don't leak the scratch page
Recently discovered by enabling CONFIG_DMA_API_DEBUG in our CI. By the
looks of it broken since forever.
v2: Don't forget to set the scratch page back to wb (Chris). Reuse
intel_gtt_teardown_scratch_page for that (and fix it up to treat
needs_dmar y/n correctly).
Nick Hoath [Fri, 22 Jan 2016 23:10:06 +0000 (23:10 +0000)]
drm/i915: fix context/engine cleanup order
Swap the order of context & engine cleanup, so that contexts are cleaned
up first, and *then* engines. This is a more sensible order anyway, but
in particular has become necessary since the 'intel_ring_initialized()
must be simple and inline' patch, which now uses ring->dev as an
'initialised' flag, so it can now be NULL after engine teardown. This
in turn can cause a problem in the context code, which (used to) check
the ring->dev->struct_mutex -- causing a fault if ring->dev was NULL.
Also rename the cleanup function to reflect what it actually does
(cleanup engines, not a ringbuffer), and fix an annoying whitespace issue.
v2: Also make the fix in i915_load_modeset_init, not just in
i915_driver_unload (Chris Wilson)
v3: Had extra stuff in it.
v4: Reverted extra stuff (so we're back to v2).
Rebased and updated commentary above (Dave Gordon).
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com> Signed-off-by: David Gordon <david.s.gordon@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1453504211-7982-2-git-send-email-david.s.gordon@intel.com
Gabriel Feceoru [Fri, 22 Jan 2016 11:28:45 +0000 (13:28 +0200)]
drm/i915: Handle PipeC fused off on IVB/HSW/BDW
Some Gen7/8 production parts may have the Display Pipe C fused off.
In this case, the display hardware will prevent the enable bit in
PIPE_CONF register (for Pipe C) from being set to 1.
Fixed by adjusting pipe_count to reflect this.
v2: Rename HSW_PIPE_C_DISABLE to IVB_PIPE_C_DISABLE as it already exists
on ivybridge (Ville)
v3: Remove unnecessary MMIO read, correct the description (Damien)
v4: Be more specific in description (Patrick)
Lyude [Thu, 4 Feb 2016 15:43:21 +0000 (10:43 -0500)]
drm/i915/skl: Fix typo in DPLL_CFGCR1 definition
We accidentally point both cfgcr registers for the second shared DPLL to
the same location in i915_reg.h. This results in a lot of hw pipe state
mismatches whenever we try to do a modeset that requires allocating the
DPLL to a CRTC:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)
This usually ends up causing blank monitors, since the DPLL never can
get set to the right clock.
drm/gma500: fix error path in gma_intel_setup_gmbus()
The current code fails to call i2c_del_adapter on
dev_prev->gmbus[0].adapter, and if the for loop above failed already
at i==0, all hell breaks loose when we do the loop body for
i = -1,-2,...
LABBE Corentin [Thu, 4 Feb 2016 14:03:52 +0000 (15:03 +0100)]
drm: modes: add missing [drm] to message printing
The warning message in drm_mode_parse_command_line_for_connector miss
the [drm] at beginning.
This patch add it and take the opportunity to convert
printk(KERN_WARNING to pr_warn()
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/radeon: Defer probe if gmux is present but its driver isn't
gmux is a microcontroller built into dual GPU MacBook Pros.
On pre-retina MBPs, if we're the inactive GPU, we need apple-gmux
to temporarily switch DDC so that we can probe the panel's EDID.
The checks for CONFIG_VGA_ARB and CONFIG_VGA_SWITCHEROO are necessary
because if either of them is disabled but gmux is present, the driver
would never load, even if we're the active GPU. (vga_default_device()
would evaluate to NULL and vga_switcheroo_handler_flags() would
evaluate to 0.)
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/nouveau: Defer probe if gmux is present but its driver isn't
gmux is a microcontroller built into dual GPU MacBook Pros.
On pre-retina MBPs, if we're the inactive GPU, we need apple-gmux
to temporarily switch DDC so that we can probe the panel's EDID.
The checks for CONFIG_VGA_ARB and CONFIG_VGA_SWITCHEROO are necessary
because if either of them is disabled but gmux is present, the driver
would never load, even if we're the active GPU. (vga_default_device()
would evaluate to NULL and vga_switcheroo_handler_flags() would
evaluate to 0.)
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/i915: Defer probe if gmux is present but its driver isn't
gmux is a microcontroller built into dual GPU MacBook Pros.
On pre-retina MBPs, if we're the inactive GPU, we need apple-gmux
to temporarily switch DDC so that we can probe the panel's EDID.
The checks for CONFIG_VGA_ARB and CONFIG_VGA_SWITCHEROO are necessary
because if either of them is disabled but gmux is present, the driver
would never load, even if we're the active GPU. (vga_default_device()
would evaluate to NULL and vga_switcheroo_handler_flags() would
evaluate to 0.)
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
apple-gmux: Add helper for presence detect
Centralize gmux' ACPI HID in a header file and add apple_gmux_present().
This can be used by other drivers to activate quirks specific to dual
GPU MacBook Pros & Mac Pros. The alternative would be to hardcode DMI
or PCI IDs and amend them whenever Apple introduces a new machine.
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/radeon: Switch DDC when reading the EDID
The pre-retina MacBook Pro uses an LVDS panel and a gmux controller
to switch the panel between its two GPUs. The panel mode in VBIOS
is notoriously bogus on these machines.
Use drm_get_edid_switcheroo() in lieu of drm_get_edid() on LVDS
if the vga_switcheroo handler is capable of temporarily switching
the panel's DDC lines to the discrete GPU. This allows us to retrieve
the EDID if the panel is currently muxed to the integrated GPU.
This only enables EDID probing on the pre-retina MBP (2008 - 2013).
The retina MBP (2012 - present) uses eDP and gmux is not capable of
switching AUX separately from the main link on these models.
This will be addressed in later patches.
List of pre-retina MBPs with dual GPUs, one of them AMD:
[MBP 8,2 2011 intel SNB + amd turks pre-retina 15"]
[MBP 8,3 2011 intel SNB + amd turks pre-retina 17"]
v3: Commit newly added due to introduction of drm_get_edid_switcheroo()
wrapper which drivers need to opt-in to.
v5: Rebase on "vga_switcheroo: Add handler flags infrastructure",
i.e. call drm_get_edid_switcheroo() only if the handler
indicates that DDC is switchable.
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/nouveau: Switch DDC when reading the EDID
The pre-retina MacBook Pro uses an LVDS panel and a gmux controller
to switch the panel between its two GPUs. The panel mode in VBIOS
is notoriously bogus on these machines.
Use drm_get_edid_switcheroo() in lieu of drm_get_edid() on LVDS
if the vga_switcheroo handler is capable of temporarily switching
the panel's DDC lines to the discrete GPU. This allows us to retrieve
the EDID if the panel is currently muxed to the integrated GPU.
Likewise, ask vga_switcheroo to switch DDC before probing LVDS
connectors.
This only enables EDID probing on the pre-retina MBP (2008 - 2013).
The retina MBP (2012 - present) uses eDP and gmux is not capable of
switching AUX separately from the main link on these models.
This will be addressed in later patches.
List of pre-retina MBPs with dual GPUs, either or both Nvidia:
[MBP 5,1 2008 nvidia MCP79 + G96 pre-retina 15"]
[MBP 5,2 2009 nvidia MCP79 + G96 pre-retina 17"]
[MBP 5,3 2009 nvidia MCP79 + G96 pre-retina 15"]
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina 15"]
[MBP 6,1 2010 intel ILK + nvidia GT216 pre-retina 17"]
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
v3: Commit newly added due to introduction of drm_get_edid_switcheroo()
wrapper which drivers need to opt-in to.
v5: Rebase on "vga_switcheroo: Add handler flags infrastructure",
i.e. call drm_get_edid_switcheroo() only if the handler
indicates that DDC is switchable.
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/i915: Switch DDC when reading the EDID
The pre-retina MacBook Pro uses an LVDS panel and a gmux controller
to switch the panel between its two GPUs. The panel mode in VBIOS
is notoriously bogus on these machines and some models have no
VBIOS at all.
Use drm_get_edid_switcheroo() in lieu of drm_get_edid() on LVDS
if the vga_switcheroo handler is capable of temporarily switching
the panel's DDC lines to the integrated GPU. This allows us to
retrieve the EDID if the panel is currently muxed to the discrete GPU.
This only enables EDID probing on the pre-retina MBP (2008 - 2013).
The retina MBP (2012 - present) uses eDP and gmux is not capable of
switching AUX separately from the main link on these models.
This will be addressed in later patches.
List of pre-retina MBPs with dual GPUs, one of them Intel:
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina 15"]
[MBP 6,1 2010 intel ILK + nvidia GT216 pre-retina 17"]
[MBP 8,2 2011 intel SNB + amd turks pre-retina 15"]
[MBP 8,3 2011 intel SNB + amd turks pre-retina 17"]
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
v3: Commit newly added due to introduction of drm_get_edid_switcheroo()
wrapper which drivers need to opt-in to.
v5: Rebase on "vga_switcheroo: Add handler flags infrastructure",
i.e. call drm_get_edid_switcheroo() only if the handler
indicates that DDC is switchable.
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
drm/edid: Switch DDC when reading the EDID
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
Some dual graphics machines support muxing the DDC separately from
the display, so make use of this functionality when reading the EDID
on the inactive GPU. Also serialize drm_get_edid() with a mutex to
avoid races on the DDC mux state.
Modified by Dave Airlie <airlied@gmail.com>, 2012-12-22:
I can't figure out why I didn't like this, but I rewrote this [...]
to lock/unlock the ddc lines [...]. I think I'd prefer something
like that otherwise the interface got really ugly.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-09:
v3: Move vga_switcheroo calls to a wrapper around drm_get_edid()
which drivers can call on muxed machines. This avoids other
drivers having to go through the vga_switcheroo motions even
though they are never used on a muxed platform
(Thierry Reding, Daniel Vetter, Alex Deucher)
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
apple-gmux: Add switch_ddc support
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
The gmux allows muxing the DDC independently from the display, so
support this functionality. This will allow reading the EDID for the
inactive GPU, fixing issues with machines that either don't have a
VBT or have invalid mode data in the VBT.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-12:
Change semantics of ->switch_ddc handler callback to return previous
DDC owner. Original version tried to determine previous DDC owner
with find_active_client() in vga_switcheroo but this fails if the
inactive client registers before the active client.
v2.4: Retain semantics of ->switchto handler callback to switch all
pins, including DDC (Daniel Vetter)
v4: Advertise ->switch_ddc handler callback only on the pre-retina
Macbook Pro. The retina uses eDP instead of LVDS and gmux no
longer does the muxing itself but merely controls an external
mux. That mux is incapable of switching the AUX channel
separately from the main link. It's an NXP CBTL06142
(alternate parts: TI HD3SS212, Pericom PI3VDP12412,
see datasheets below).
v5: Rebase on "apple-gmux: Track switch state".
Rebase on "vga_switcheroo: Add handler flags infrastructure".
Rebase on 5d170139eb10 ("Constify vga_switcheroo_handler"),
requires 2 structs, 1x with ->switchto for pre-retinas,
1x without for retinas).
Add error message if handler registration with vga_switcheroo
fails.
Teardowns identifying the mux:
http://www.electronicproducts.com/-whatsinside_text-145.aspx
http://slideshare.net/jjwu6266/apple-2012-wwdc-apple-macbook-pro-with-retina-display
http://www.techrepublic.com/blog/cracking-open/teardown-shows-retina-macbook-pro-is-nearly-impossible-to-upgrade-difficult-to-work-on/
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
apple-gmux: Track switch state
gmux has 3 switch registers:
* GMUX_PORT_SWITCH_DISPLAY switches the panel
* GMUX_PORT_SWITCH_DDC switches the panel's DDC lines
(only on pre-retinas; on retinas this is a no-op)
* GMUX_PORT_SWITCH_EXTERNAL switches the external DP port(s)
(only on models without Thunderbolt, i.e. introduced before 2011;
those with Thunderbolt switch only HPD/AUX, not the main link)
Currently we switch all 3 registers in unison.
gmux does not preserve the switch state during suspend, so we currently
read GMUX_PORT_SWITCH_DISPLAY before suspend and restore all 3 registers
to this value on resume.
With the upcoming ->switch_ddc callback, GMUX_PORT_SWITCH_DDC may
temporarily contain a different value than the other 2 registers.
If we happen to suspend at this moment, we'll write an incorrect
value to GMUX_PORT_SWITCH_DDC on resume.
Also, on models with Thunderbolt the integrated GPU is unable to drive
the external DP port(s), so we want to keep GMUX_PORT_SWITCH_EXTERNAL
permanently switched to the discrete GPU on those machines.
Consequently we can no longer assume that GMUX_PORT_SWITCH_DISPLAY
represents the correct value for all 3 registers on suspend.
Track the state of all 3 registers: Add gmux_read_switch_state() and
gmux_write_switch_state(). Instead of reading the switch state on
every suspend, read it once on driver initialization so that we know
the current switch state all the time. (This allows us to use some
optimizations and shortcuts, e.g. we can skip switching DDC if we
know that it's already switched to the requested GPU.) Change the
->switchto callback to use gmux_write_switch_state().
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
vga_switcheroo: Add support for switching only the DDC
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
During graphics driver initialization it's useful to be able to mux
only the DDC to the inactive client in order to read the EDID. Add
a switch_ddc callback to allow capable handlers to provide this
functionality, and add vga_switcheroo_switch_ddc() to allow DRM
to mux only the DDC.
Modified by Dave Airlie <airlied@gmail.com>, 2012-12-22:
I can't figure out why I didn't like this, but I rewrote this [...]
to lock/unlock the ddc lines [...]. I think I'd prefer something
like that otherwise the interface got really ugly.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-10:
Change semantics of ->switch_ddc handler callback to return previous
DDC owner. Original version tried to determine previous DDC owner
with find_active_client() but this fails if the inactive client
registers before the active client.
Don't lock vgasr_mutex in _lock_ddc() / _unlock_ddc(), it can cause
deadlocks because (a) during switch (with vgasr_mutex already held),
GPU is woken and probes its outputs, tries to re-acquire vgasr_mutex
to lock DDC lines; (b) Likewise during switch, GPU is suspended and
calls cancel_delayed_work_sync() to stop output polling, if poll
task is running at this moment we may wait forever for it to finish.
Instead, lock mux_hw_lock when unregistering the handler because
the only reason why we'd want to lock vgasr_mutex in _lock_ddc() /
_unlock_ddc() is to block the handler from disappearing while DDC
lines are switched.
Also acquire mux_hw_lock in stage2 to avoid race condition where
reading the EDID and switching happens simultaneously. Likewise on
MIGD / MDIS commands and on runtime suspend.
v2.4: Retain semantics of ->switchto handler callback to switch all
pins, including DDC (Daniel Vetter)
v5: Rename ddc_lock to mux_hw_lock: Since we acquire this both
when calling ->switch_ddc and ->switchto, it protects not just
access to the DDC lines but to the mux in general. This is in
line with the DRM convention to use low-level locks to avoid
concurrent hw access (e.g. i2c, dp_aux) which are often called
hw_lock (Daniel Vetter)
Lukas Wunner [Mon, 11 Jan 2016 19:09:20 +0000 (20:09 +0100)]
vga_switcheroo: Add handler flags infrastructure
Allow handlers to declare their capabilities and allow clients to
obtain that information. So far we have these use cases:
* If the handler is able to switch DDC separately, clients need to
probe EDID with drm_get_edid_switcheroo(). We should allow them
to detect a capable handler to ensure this function only gets
called when needed.
* Likewise if the handler is unable to switch AUX separately, the active
client needs to communicate link training parameters to the inactive
client, which may then skip the AUX handshake and set up its output
with these pre-calibrated values (DisplayPort specification v1.1a,
section 2.5.3.3). Clients need a way to recognize such a situation.
The flags for the radeon_atpx_handler and amdgpu_atpx_handler are
initially set to 0, this can later on be amended with
handler_flags |= VGA_SWITCHEROO_CAN_SWITCH_DDC;
when a ->switch_ddc callback is added.
This allows iteration over encoders without requiring connection_mutex.
Changes since v1:
- Add a set_best_encoder helper function and update encoder_mask inside
it.
Changes since v2:
- Relax the WARN_ON(!crtc), with explanation.
- Call set_best_encoder when connector is moved between crtc's.
- Add some paranoia to steal_encoder to prevent accidentally setting
best_encoder to NULL.
Tiago Vignatti [Tue, 22 Dec 2015 21:36:48 +0000 (19:36 -0200)]
drm/i915: Use CPU mapping for userspace dma-buf mmap()
Userspace is the one in charge of flush CPU by wrapping mmap with
begin{,end}_cpu_access.
v2: Remove LLC check cause we have dma-buf sync providers now. Also, fix return
before transferring ownership when mmap fails.
v3: Fix return values.
v4: !obj->base.filp is user triggerable, so removed the WARN_ON.
Tiago Vignatti [Tue, 22 Dec 2015 21:36:47 +0000 (19:36 -0200)]
drm/i915: Implement end_cpu_access
This function is meant to be used with dma-buf mmap, when finishing the CPU
access of the mapped pointer.
The error case should be rare to happen though, requiring the buffer become
active during the sync period and for the end_cpu_access to be interrupted. So
we use a uninterruptible mutex_lock to spit out when it ever happens.
v2: disable interruption to make sure errors are reported.
v3: update to the new end_cpu_access API.
v7: use .write = false cause it doesn't need to know whether it's write.
Lyude [Tue, 2 Feb 2016 15:49:43 +0000 (10:49 -0500)]
drm/i915/skl: Don't skip mst encoders in skl_ddi_pll_select()
We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a
result we skip assigning a DPLL to any DP MST ports, which makes link
training fail:
[ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well
[ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well
[ 1442.933957] [drm:intel_mst_pre_enable_dp] 0
[ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000
[ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0
[ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0
[ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000
[ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1
[ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1
[ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000
[ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2
…
[ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up
[ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting
After which the pipe state goes completely out of sync:
[ 70.075596] [drm:check_crtc_state] [CRTC:25]
[ 70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001)
[ 70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0)
[ 70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021)
[ 70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173)
[ 70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5)
[ 70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256)
[ 70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500)
And if you're especially lucky, it keeps going downhill:
Tiago Vignatti [Tue, 22 Dec 2015 21:36:45 +0000 (19:36 -0200)]
dma-buf: Remove range-based flush
This patch removes range-based information used for optimizations in
begin_cpu_access and end_cpu_access.
We don't have any user nor implementation using range-based flush. It seems a
consensus that if we ever want something like that again (or even more robust
using 2D, 3D sub-range regions) we can use the upcoming dma-buf sync ioctl for
such.
Daniel Thompson [Tue, 22 Dec 2015 21:36:44 +0000 (19:36 -0200)]
drm: prime: Honour O_RDWR during prime-handle-to-fd
Currently DRM_IOCTL_PRIME_HANDLE_TO_FD rejects all flags except
(DRM|O)_CLOEXEC making it difficult (maybe impossible) for userspace
to mmap() the resulting dma-buf even when this is supported by the
DRM driver.
It is trivial to relax the restriction and permit read/write access.
This is safe because the flags are seldom touched by drm; mostly they
are passed verbatim to dma_buf calls.
v3 (Tiago): removed unused flags variable from drm_prime_handle_to_fd_ioctl.
Dave Airlie [Tue, 9 Feb 2016 00:39:11 +0000 (10:39 +1000)]
Merge tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel into drm-next
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
Dave Airlie [Tue, 9 Feb 2016 00:27:41 +0000 (10:27 +1000)]
Merge tag 'drm-intel-next-2016-01-24' of git://anongit.freedesktop.org/drm-intel into drm-next
- support for v3 vbt dsi blocks (Jani)
- improve mmio debug checks (Mika Kuoppala)
- reorg the ddi port translation table entries and related code (Ville)
- reorg gen8 interrupt handling for future platforms (Tvrtko)
- refactor tile width/height computations for framebuffers (Ville)
- kerneldoc integration for intel_pm.c (Jani)
- move default context from engines to device-global dev_priv (Dave Gordon)
- make seqno/irq ordering coherent with execlist (Chris)
- decouple internal engine number from UABI (Chris&Tvrtko)
- tons of small fixes all over, as usual
* tag 'drm-intel-next-2016-01-24' of git://anongit.freedesktop.org/drm-intel: (148 commits)
drm/i915: Update DRIVER_DATE to 20160124
drm/i915: Seal busy-ioctl uABI and prevent leaking of internal ids
drm/i915: Decouple execbuf uAPI from internal implementation
drm/i915: Use ordered seqno write interrupt generation on gen8+ execlists
drm/i915: Limit the auto arming of mmio debugs on vlv/chv
drm/i915: Tune down "GT register while GT waking disabled" message
drm/i915: tidy up a few leftovers
drm/i915: abolish separate per-ring default_context pointers
drm/i915: simplify allocation of driver-internal requests
drm/i915: Fix NULL plane->fb oops on SKL
drm/i915: Do not put big intel_crtc_state on the stack
Revert "drm/i915: Add two-stage ILK-style watermark programming (v10)"
drm/i915: add DOC: headline to RC6 kernel-doc
drm/i915: turn some bogus kernel-doc comments to normal comments
drm/i915/sdvo: revert bogus kernel-doc comments to normal comments
drm/i915/gen9: Correct max save/restore register count during gpu reset with GuC
drm/i915: Demote user facing DMC firmware load failure message
drm/i915: use hlist_for_each_entry
drm/i915: skl_update_scaler() wants a rotation bitmask instead of bit number
drm/i915: Don't reject primary plane windowing with color keying enabled on SKL+
...
drm/i915: Do not disable cxsr when crtc is disabled.
It's safe to assume cxsr is already disabled when the crtc is off.
This prevents an unclaimed register warning when the required power
wells are not enabled.
This is a revert of commit 066cf55b9ce3 "drm/i915: Fix IPS related flicker".
intel_pre_disable_primary already handles this, and now everything
goes through the atomic path there's no need to try to disable ips twice.
Alan Cox [Fri, 29 Jan 2016 19:37:48 +0000 (19:37 +0000)]
gma500: clean up an excessive and confusing helper
This is a left over from the great clean ups in the past. It's confusing as
it returns an int, yet has one caller that never uses it. The caller already
has all the right private variables local so the entire function can be
replaced by a simple if call.
Sudip Mukherjee [Tue, 2 Feb 2016 06:05:55 +0000 (11:35 +0530)]
drm/gma500: remove helper function
We were getting build warning about:
drivers/gpu/drm/gma500/mdfld_dsi_output.c:407:2: warning: initialization
from incompatible pointer type
The callback to dpms was pointing to a helper function which had a
return type of void, whereas the callback should point to a function
which has a return type of int.
On closer look it turned out that we do not need the helper function
since if we call drm_helper_connector_dpms() directly, the first check
that drm_helper_connector_dpms() does is: if (mode == connector->dpms)
Daniel Vetter [Mon, 25 Jan 2016 21:16:56 +0000 (22:16 +0100)]
drm/vmwgfx: Nuke preclose hook
Again since the drm core takes care of event unlinking/disarming this
is now just needless code.
v2: I've completely missed eaction->fpriv_head and all the related
code. We need to nuke that too to avoid accidentally deferencing the
freed-up vmwgfx-private fpriv.
v3: Also remove vmw_fpriv->fence_events and unused variables I missed.
projects / mirror_ubuntu-disco-kernel.git / log