Hante Meuleman [Wed, 3 Dec 2014 20:05:33 +0000 (21:05 +0100)]
brcmfmac: add multiple BSS support.
This patch adds support for multiple BSS interfaces (AP). In
total three AP configurations can be created. In order to use
multiple BSS firmware needs to support it.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 3 Dec 2014 20:05:29 +0000 (21:05 +0100)]
brcmfmac: Add PCIE ids for 43602 devices.
Some 43602 devices are band specific and identify themselves
with different PCIE device ID. This patch adds support for the
43602 2.4G and 5.0G devices used in for example R8000 router.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wake On Lan was not working on laptop DELL Vostro 1500.
If WOL was turned on, BCM4401 was powered up in suspend mode. LEDs blinked.
But the laptop could not be woken up with the Magic Packet. The reason for
that was that PCIE was not enabled as a system wakeup source and
therefore the host PCI bridge was not powered up in suspend mode.
PCIE was not enabled in suspend by PM because no child devices were
registered as wakeup source during suspend process.
On laptop BCM4401 is connected through the SSB bus, that is connected to the
PCI-Express bus. SSB and B44 did not use standard PM wakeup functions
and did not forward wakeup settings to their parents.
To fix that B44 driver enables PM wakeup and registers new wakeup source
using device_set_wakeup_enable(). Wakeup is automatically reported to the parent SSB
bus via power.wakeup_path. SSB bus enables wakeup for the parent PCI bridge, if there is any
child devices with enabled wakeup functionality. All other steps are
done by PM core code.
Signed-off-by: Andrey Skvortsov <Andrej.Skvortzov@gmail.com> Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: John W. Linville <linville@tuxdriver.com>
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julien Lefrique [Tue, 2 Dec 2014 15:25:01 +0000 (16:25 +0100)]
NFC: NCI: Fix max length of General Bytes in ATR_RES
The maximum size of ATR_REQ and ATR_RES is 64 bytes.
The maximum number of General Bytes is calculated by
the maximum number of data bytes in the ATR_REQ/ATR_RES,
substracted by the number of mandatory data bytes.
ATR_REQ: 16 mandatory data bytes, giving a maximum of
48 General Bytes.
ATR_RES: 17 mandatory data bytes, giving a maximum of
47 General Bytes.
NFC: hci: Add specific hci macro to not create a pipe
Some pipe are only created by other host (different than the
Terminal Host).
The pipe values will for example be notified by
NFC_HCI_ADM_NOTIFY_PIPE_CREATED.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: netlink: Add new netlink command NFC_CMD_ACTIVATE_TARGET
Some tag might get deactivated after some read or write tentative.
This may happen for example with Mifare Ultralight C tag when trying
to read the last 4 blocks (starting block 0x2c) configured as write
only.
NFC_CMD_ACTIVATE_TARGET will try to reselect the tag in order to
detect if it got remove from the field or if it is still present.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: nci: Add support for different NCI_DEACTIVATE_TYPE
nci_rf_deactivate_req only support NCI_DEACTIVATE_TYPE_IDLE_MODE.
In some situation, it might be necessary to be able to support other
NCI_DEACTIVATE_TYPE such as NCI_DEACTIVATE_TYPE_SLEEP_MODE in order for
example to reactivate the selected target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: nci: Add management for NCI state for machine rf_deactivate_ntf
A notification for rf deaction can be IDLE_MODE, SLEEP_MODE,
SLEEP_AF_MODE and DISCOVERY. According to each type and the NCI
state machine is different (see figure 10 RF Communication State
Machine in NCI specification)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: nci: Add status byte management in case of error.
The nci status byte was ignored. In case of tag reading for example,
if the tag is removed from the antenna there is no way for the upper
layers (aka: stack) to get inform about such event.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eran Harary [Mon, 1 Dec 2014 15:40:37 +0000 (17:40 +0200)]
iwlwifi: mvm: Ability to work with packed usniffer image
The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Liad Kaufman [Mon, 17 Nov 2014 09:44:03 +0000 (11:44 +0200)]
iwlwifi: pcie: support more monitor types dumping
Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Liad Kaufman [Mon, 17 Nov 2014 09:41:07 +0000 (11:41 +0200)]
iwlwifi: pcie: config regs according to fw tlv
Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Liad Kaufman [Mon, 17 Nov 2014 09:36:21 +0000 (11:36 +0200)]
iwlwifi: mvm: send dbg config hcmds to fw if set in tlv
Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Debug information can be appended to the firmware file. This
information will be used by the driver to enable / disable
debugging features in the firmware.
Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:
This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961
Cc: <stable@vger.kernel.org> Fixes: a0855054e59b ("iwlwifi: dvm: drop non VO frames when flushing") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Liad Kaufman [Thu, 30 Oct 2014 12:27:13 +0000 (14:27 +0200)]
iwlwifi: use correct fw file in 8000 b-step
In 8000 B-step the FW file has changed, but by the time we
know the HW step, the FW file is already requested.
This patch defaults 8000 family to B-step if no HW step is
detected in time. When it can it checks what HW step it
really is (in 8000 family) and if it isn't B-step, the FW
file is released and the A-step file is requested.
If our terminal connect with other host like UICC, it may create
a pipe with us, the host controller will notify us new pipe
created, after that UICC will open that pipe, if we don't handle
that request, UICC may failed to continue initialize which may
lead to card emulation feature failed to work
Signed-off-by: Arron Wang <arron.wang@intel.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st21nfcb: Remove gpio_irq field in static and dts configuration
- phy->gpio_irq is never done out of the request resources.
- irq_of_parse_and_map is already done in the i2c core so client->irq is
already set when entering in st21nfcb_hci_i2c_of_request_resources
- In case of static platform configuration client->irq can be set directly.
- It simplifies the code a bit.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st21nfca: Remove gpio_irq field in static and dts configuration
- phy->gpio_irq is never done out of the request resources.
- irq_of_parse_and_map is already done in the i2c core so client->irq is
already set when entering in st21nfca_hci_i2c_of_request_resources
- In case of static platform configuration client->irq can be set directly
- It simplifies the code a bit.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.
Rate-limit it to prevent dmesg flooding.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()
Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 30 Nov 2014 20:58:32 +0000 (21:58 +0100)]
ath9k: do not access hardware on IRQs during reset
Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 30 Nov 2014 20:52:57 +0000 (21:52 +0100)]
ath5k: fix hardware queue index assignment
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 30 Nov 2014 19:38:40 +0000 (20:38 +0100)]
ath9k_hw: fix hardware queue allocation
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Cc: stable@vger.kernel.org Reported-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 28 Nov 2014 09:43:40 +0000 (12:43 +0300)]
brcmsmac: NULL dereferences in brcms_c_detach_mfree()
The brcms_c_attach_malloc() function can call this with a NULL
"wlc->corestate" or "wlc->hw".
Also I threw in a bonus cleanup by deleting an obvious comment and a
no-op NULL assignment. :)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revert "rt2x00: Endless loop on hub port power down"
This reverts commit 2ad69ac5976191e9bb7dc4044204a504653ad1bb. It
causes wireless device disappear when we get -EPROTO error form USB
request. I encounter such situation occasionally when resume form
suspend with RT3070 adapter:
[ 289.619985] ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x0404 with error -71
[ 289.639368] ieee80211 phy0: rt2800_wait_bbp_ready: Error - BBP register access failed, aborting
[ 289.639374] ieee80211 phy0: rt2800usb_set_device_state: Error - Device failed to enter state 4 (-5)
Without the patch, except printing error, device works just fine after
resume.
Currently after timeouts and REGISTER_BUSY_COUNT tuning, we should
not have any "endless loop", though we can wait quite long when driver
is trying to communicate with the device through non functioning USB
connection. Generally the problem that commit 2ad69ac597619 solves
is kinda artificial.
Cc: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 25 Nov 2014 19:55:53 +0000 (20:55 +0100)]
brcmutil: add helper function to format board revision
The board revision that is available in hardware can be translated
so it matches the labelling on the board. This is accomplished by
this helper function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800: calculate tx power temperature compensation on selected chips
Currently implemented temperature compensation is only valid on some of
supported chips. Other chips do not need temperature compensation or
need different way to do this (not yet implemented in the rt2800
driver). Trying to do run rt2800_get_gain_calibration_delta() when this
is not appropriate on particular chip gives bogus result of TX power
and can make connection unstable.
This is follow up to commit 8c8d2017ba25c510ddf093419048460db1109bc4
"rt2800: fix RT5390 & RT3290 TX power settings regression". On that
commit we avoid setting BBP_R1 register, but the real problem is wrong
temperature compensation calculation.
Reported-and-tested-by: Ronald Wahl <ronald.wahl@raritan.com> Debugged-by: Ronald Wahl <ronald.wahl@raritan.com> Cc: Mike Romberg <mike-romberg@comcast.net> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lino Sanfilippo [Fri, 28 Nov 2014 01:47:19 +0000 (02:47 +0100)]
wil6210: Fix potential memory leaks on error paths
Fix missing memory deallocation on error paths in wil_write_file_wmi()
and wil_write_file_txmgmt().
Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Liad Kaufman [Sun, 23 Nov 2014 11:56:21 +0000 (13:56 +0200)]
iwlwifi: pcie: add fh registers to dump data
Adds all FH registers between FH_MEM_UPPER_BOUND and
FH_MEM_LOWER_BOUND (which should be readable to the driver)
to the dump data when it is collected.
7265D are new devices that should always have a new NVM
(at least 0x0c11). The firmware has issues with older
versions of the NVM which are not and will not be available
to the common mortals.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Luciano Coelho [Fri, 21 Nov 2014 20:08:01 +0000 (22:08 +0200)]
iwlwifi: mvm: add channel information to the netdetect notifications
Add the channels on which there was a match for every match reported
by the firmware. The firmware reports the channels as indices to the
array of channels that was passed in the scheduled scan request, so we
need to save the array when entering D3 to make sure it is available
when we resume.
Luciano Coelho [Fri, 21 Nov 2014 07:32:23 +0000 (09:32 +0200)]
iwlwifi: mvm: add SSID match information for net-detect
Add SSID information to the net-detect indication to userspace. Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.
Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
projects / mirror_ubuntu-eoan-kernel.git / log