Arnd Bergmann [Fri, 5 Jan 2018 16:07:32 +0000 (17:07 +0100)]
Merge tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.16" from Shawn Guo:
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
ARM: dts: imx7s: Avoid using label in unit address and reg
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
ARM: dts: vf610-zii-dev: enable edma1
ARM: dts: ls1021a-twr: Remove extra clock cell
ARM: dts: ls1021a-qds: Remove extra clock cell
ARM: dts: imx53: add srtc node
dt-bindings: imx-gpcv2: Fix the unit address
ARM: imx: dts: Use lower case for bindings notation
ARM: dts: imx6q-h100: use usdhc2 VSELECT
ARM: dts: imx6sx: Add support for PCI power domain
ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
ARM: dts: imx6qdl-hummingboard2: add PWM3 support
...
Arnd Bergmann [Fri, 5 Jan 2018 16:06:04 +0000 (17:06 +0100)]
Merge tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "ASPEED device tree updates for 4.16" from Joel Stanley:
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
Linus Walleij [Tue, 2 Jan 2018 07:57:17 +0000 (08:57 +0100)]
ARM: dts: Delete bogus reference to the charlcd
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Olof Johansson [Fri, 5 Jan 2018 07:30:28 +0000 (23:30 -0800)]
Merge tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.16
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
* tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers
ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers
ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: vinco: use TCB2 as timers
ARM: dts: at91: ma5d4: use TCB2 as timers
ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers
ARM: dts: at91: sama5d4ek: use TCB2 as timers
ARM: dts: at91: sama5d4: Add TCB2
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: linea/tse850-3: use TCB0 as timers
ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers
ARM: dts: at91: kizbox2: use TCB0 as timers
ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d3xek: use TCB0 as timers
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: kizboxmini: use TCB0 as timers
ARM: dts: at91: cosino: use TCB0 as timers
ARM: dts: at91: acme/g25: use TCB0 as timers
ARM: dts: at91: at91sam9x5cm: use TCB0 as timers
...
Olof Johansson [Fri, 5 Jan 2018 07:29:34 +0000 (23:29 -0800)]
Merge tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.16
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
* tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
arm64: dts: uniphier: add GPIO hog definition for PXs3
arm64: dts: uniphier: use macros in dt-bindings header
Olof Johansson [Fri, 5 Jan 2018 07:28:00 +0000 (23:28 -0800)]
Merge tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.16
- clean up gpios properties by macro
- add efuse nodes
- add has-transaction-translator property to generic-ehci nodes
* tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add has-transaction-translator property to usb node for LD4, sLD8 and Pro4
ARM: dts: uniphier: add efuse node for UniPhier 32bit SoC
ARM: dts: uniphier: use macros in dt-bindings header
Olof Johansson [Fri, 5 Jan 2018 07:18:15 +0000 (23:18 -0800)]
Merge tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT64 changes for 4.16
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
Olof Johansson [Fri, 5 Jan 2018 07:17:16 +0000 (23:17 -0800)]
Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
* tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1
ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings
ARM: dts: sun8i: a83t: Add I2S controller device nodes
ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY
ARM: dts: sun8i: a83t: Enable Ethernet on two boards
ARM: dts: sun8i: a83t: add dwmac-sun8i device node
ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board
ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.
ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
ARM: dtsi: axp81x: add GPIO DT node
ARM: dts: sun8i: add support for Orange Pi R1
ARM: dts: sunxi: Add codec for A13 Olinuxino
Olof Johansson [Fri, 5 Jan 2018 07:12:16 +0000 (23:12 -0800)]
Merge tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
ARM: Keystone DTS update for 4.16
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
* tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2l-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-hk-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone: Add missing unit name to interrupt controller
ARM: dts: keystone: Get rid of usage of skeleton.dtsi
ARM: dts: keystone*: Use a single soc0 instance
ARM: dts: keystone*: Standardize license with SPDX tag
ARM: dts: k2g-evm: Enable UART 2
ARM: dts: k2g: Add UART 1 and 2 instances
ARM: dts: keystone: Add generic compatible string for I2C EEPROM
ARM: dts: keystone-k2g-ice: Add DT nodes for few peripherals
ARM: dts: keystone-k2g-evm: Add QSPI DT node.
ARM: dts: keystone-k2g: Move ti,non-removable property to board dts
ARM: dts: keystone-k2g-evm: Fix botched up merge
ARM: dts: keystone-k2g: Add QSPI DT entry
ARM: dts: keystone-k2l: Add the second gpio bank node
Olof Johansson [Fri, 5 Jan 2018 06:58:00 +0000 (22:58 -0800)]
Merge tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.16 (part 1)
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
* tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Add thermal support for A7K/A8K
arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support
arm64: dts: marvell: add NAND support on the 8040-DB board
Olof Johansson [Fri, 5 Jan 2018 06:52:45 +0000 (22:52 -0800)]
Merge tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.16 (part 1)
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
* tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu:
arm: kirkwood: dts: Use lower case for bindings notation
ARM: dts: armada-38x: Add NAND RB pinctrl information
Olof Johansson [Fri, 5 Jan 2018 06:51:06 +0000 (22:51 -0800)]
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.16
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
* tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits)
ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core
ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support on DTS
ARM: dts: iwg22d-sodimm: Sound PIO support
ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec
ARM: dts: r8a7745: Add sound support
ARM: dts: r8a7745: Add audio DMAC support
ARM: dts: r8a7745: Add audio clocks
ARM: dts: r8a7740: Correct TPU register block size
ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus
ARM: dts: r8a7743: sort root sub-nodes alphabetically
ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support on DTS
ARM: dts: iwg20d-q7-common: Sound PIO support
ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec
ARM: dts: r8a7792: move timer node out of bus
...
Olof Johansson [Fri, 5 Jan 2018 06:38:49 +0000 (22:38 -0800)]
Merge tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.16
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
* tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: salvator-common: enable usb3_peri0
arm64: dts: renesas: salvator-common: enable usb3_phy0 node
arm64: dts: renesas: r8a7796: add usb3_phy node
arm64: dts: renesas: r8a7795: add usb3_phy node
arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes
arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus
arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically
arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically
arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset
arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset
arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus
Olof Johansson [Fri, 5 Jan 2018 06:35:13 +0000 (22:35 -0800)]
Merge tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.16
- Add SD card support for the hi3798cv200-poplar board
- Replace the PMU node with exact match for the hi3660 SoC
- Add cpu capacity-dmips-mhz information for the hi3660 SoC
* tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
arm64: dts: hi3660: improve pmu description
arm64: dts: hi3798cv200: add SD card support
Arnd Bergmann [Thu, 4 Jan 2018 22:55:52 +0000 (23:55 +0100)]
arm64: dts: sprd: remove broken header inclusion
The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:
In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory
It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.
Arnd Bergmann [Thu, 4 Jan 2018 16:55:54 +0000 (17:55 +0100)]
Merge tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "A second set of Gemini DTS updates for v4.16" from Linus Walleij:
- Use Open Drain flags properly for emulated I2C
- Add the PCI bus to WBD111 and WBD222
- Enable the TVE and panel on DIR-685; the panel driver and
bindings have been merged into the DRI subsystem.
* tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add TVE/TVC and ILI9322 panel to DIR-685
ARM: dts: Add PCI to WBD111 and WBD222
ARM: dts: Flags D-Link DIR-685 I2C bus gpios
Chunyan Zhang [Thu, 7 Dec 2017 12:57:15 +0000 (20:57 +0800)]
arm64: dts: add clocks for SC9860
Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.
Chunyan Zhang [Thu, 7 Dec 2017 12:57:14 +0000 (20:57 +0800)]
arm64: dts: add syscon for whale2 platform
Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.
Damien Riegel [Thu, 7 Dec 2017 15:19:40 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916-pins: move sdhc2 cd node with its siblings
Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.
Damien Riegel [Thu, 7 Dec 2017 15:19:41 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916: normalize I2C and SPI nodes
The QUP core can be used either for I2C or SPI, so the same IP is mapped
by a driver or the other. SPI bindings use a leading 0 for the start
address and a size of 0x600, I2C bindings don't have the leading 0 and
have a size 0x1000.
To make them more similar, add the leading 0 to I2C bindings and changes
the size to 0x500 for all of them, as this is the actual size of these
blocks. Also align the second entry of the clocks array.
Damien Riegel [Thu, 7 Dec 2017 15:19:36 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916: drop unused board-specific nodes
These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.
Damien Riegel [Thu, 7 Dec 2017 15:19:34 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916-pins: remove assignments to bias-disable
Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.
Indentation did not respect kernel standards, so fix that for the usual
indent with tabs, align with spaces. While at it, remove some empty
lines before and after the closing parenthesis of this block.
Bjorn Andersson [Fri, 1 Dec 2017 05:27:32 +0000 (21:27 -0800)]
arm64: dts: msm8916: Correct ipc references for smsm
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9ba4 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes") Cc: stable@vger.kernel.org Reported-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
Masahiro Yamada [Fri, 29 Dec 2017 12:41:11 +0000 (21:41 +0900)]
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
The serial pins of PXs3 SoC are not multiplexed with any other
functions. Enable serial2 and serial3 on the PXs3 reference board
because I see the connectors on the board.
Kunihiko Hayashi [Tue, 26 Dec 2017 01:03:40 +0000 (10:03 +0900)]
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
When a full/low speed device is connected to USB 2.0 port on UniPhier SoC
that has ehci controller, the kernel shows the following messages.
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: unable to enumerate USB device
To fix the issue, the driver needs to enable Transaction Translator on ehci
root hub. This adds 'has-transaction-translator' property to each node.
Kunihiko Hayashi [Tue, 26 Dec 2017 01:03:39 +0000 (10:03 +0900)]
ARM: dts: uniphier: add has-transaction-translator property to usb node for LD4, sLD8 and Pro4
When a full/low speed device is connected to USB 2.0 port on UniPhier SoC
that has ehci controller, the kernel shows the following messages.
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: unable to enumerate USB device
To fix the issue, the driver needs to enable Transaction Translator on ehci
root hub. This adds 'has-transaction-translator' property to each node.
Fabio Estevam [Tue, 26 Dec 2017 18:04:20 +0000 (16:04 -0200)]
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Commit 915fbe59cbf2fe6 ("ARM: dts: imx: Add missing #phy-cells to
usb-nop-xceiv") missed to update imx51-zii-rdu1.dts probably due to a
merge timing issue, so add #phy-cells here too.
Fabio Estevam [Tue, 26 Dec 2017 17:55:58 +0000 (15:55 -0200)]
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
Remove the leading zero from unit address to fix the following build
warning with W=1:
arch/arm/boot/dts/imx6dl-hummingboard2.dtb: Warning (unit_address_format): Node /soc/aips-bus@2100000/i2c@21a0000/codec@0a unit name should not have leading 0s
SZ Lin [Tue, 26 Dec 2017 04:54:31 +0000 (12:54 +0800)]
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
Add support for Moxa UC-8410A open platform
The UC-8410A computing platform is designed
for embedded communication-centric industrial applications
The features of UC-8410A are:
* QSPI flash
* SD slot
* 3x LAN
* 8x RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with PCIe/USB signal
* 2x USB host
* TPM
* Watchdog
* RTC
* User LEDs
* Beeper
* Push button
Signed-off-by: Jimmy Chen <jimmy.chen@moxa.com> Signed-off-by: Harry YJ Jhou <harryyj.jhou@moxa.com> Signed-off-by: SZ Lin <sz.lin@moxa.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Wed, 20 Dec 2017 23:11:55 +0000 (23:11 +0000)]
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
Switch 2 has an 88e1545 PHY behind it, which is a quad PHY. Only the
first three PHYs are used, the remaining PHY is unused. When we wire
up the SFF sockets in a later commit, the omission of this causes the
fourth PHY to be used for port 3. Specifying the PHYs in DT avoids
the auto-probing of the bus, and discovery of this PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Wed, 20 Dec 2017 23:11:45 +0000 (23:11 +0000)]
ARM: dts: vf610-zii-dev: enable edma1
EDMA1 is required for the SPI controller used on the ZII boards to be
functional. Enable EDMA1.
Fixes: 14c416336820 ("ARM: dts: vfxxx: Enable DMA for DSPI on Vybrid") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 19 Dec 2017 15:36:37 +0000 (13:36 -0200)]
ARM: dts: ls1021a-twr: Remove extra clock cell
There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
Fabio Estevam [Tue, 19 Dec 2017 15:36:36 +0000 (13:36 -0200)]
ARM: dts: ls1021a-qds: Remove extra clock cell
There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
Michael Tretter [Fri, 15 Dec 2017 09:26:24 +0000 (10:26 +0100)]
ARM: dts: imx6q-h100: use usdhc2 VSELECT
The uSDHC controller directly provides a VSELECT signal that can be
muxed to the external voltage select. Mux the VSELECT directly to avoid
using a GPIO.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
projects / mirror_ubuntu-hirsute-kernel.git / log