Damien Le Moal [Wed, 28 Feb 2018 17:35:29 +0000 (09:35 -0800)]
mq-deadline: Make sure to always unlock zones
In case of a failed write request (all retries failed) and when using
libata, the SCSI error handler calls scsi_finish_command(). In the
case of blk-mq this means that scsi_mq_done() does not get called,
that blk_mq_complete_request() does not get called and also that the
mq-deadline .completed_request() method is not called. This results in
the target zone of the failed write request being left in a locked
state, preventing that any new write requests are issued to the same
zone.
Fix this by replacing the .completed_request() method with the
.finish_request() method as this method is always called whether or
not a request completes successfully. Since the .finish_request()
method is only called by the blk-mq core if a .prepare_request()
method exists, add a dummy .prepare_request() method.
Fixes: 5700f69178e9 ("mq-deadline: Introduce zone locking support") Cc: Hannes Reinecke <hare@suse.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[ bvanassche: edited patch description ] Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 28 Feb 2018 19:18:58 +0000 (12:18 -0700)]
Merge branch 'for-jens' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Keith for 4.16-rc.
* 'for-jens' of git://git.infradead.org/nvme:
nvmet: fix PSDT field check in command format
nvme-multipath: fix sysfs dangerously created links
nvme-pci: Fix nvme queue cleanup if IRQ setup fails
nvmet-loop: use blk_rq_payload_bytes for sgl selection
nvme-rdma: use blk_rq_payload_bytes instead of blk_rq_bytes
nvme-fabrics: don't check for non-NULL module in nvmf_register_transport
Max Gurtovoy [Wed, 24 Jan 2018 15:31:45 +0000 (17:31 +0200)]
nvmet: fix PSDT field check in command format
PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.
Suggested-by: Idan Burstein <idanb@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <keith.busch@intel.com>
Baegjae Sung [Wed, 28 Feb 2018 07:06:04 +0000 (16:06 +0900)]
nvme-multipath: fix sysfs dangerously created links
If multipathing is enabled, each NVMe subsystem creates a head
namespace (e.g., nvme0n1) and multiple private namespaces
(e.g., nvme0c0n1 and nvme0c1n1) in sysfs. When creating links for
private namespaces, links of head namespace are used, so the
namespace creation order must be followed (e.g., nvme0n1 ->
nvme0c1n1). If the order is not followed, links of sysfs will be
incomplete or kernel panic will occur.
The kernel panic was:
kernel BUG at fs/sysfs/symlink.c:27!
Call Trace:
nvme_mpath_add_disk_links+0x5d/0x80 [nvme_core]
nvme_validate_ns+0x5c2/0x850 [nvme_core]
nvme_scan_work+0x1af/0x2d0 [nvme_core]
Correct order
Context A Context B
nvme0n1
nvme0c0n1 nvme0c1n1
Incorrect order
Context A Context B
nvme0c1n1
nvme0n1
nvme0c0n1
The nvme_mpath_add_disk (for creating head namespace) is called
just before the nvme_mpath_add_disk_links (for creating private
namespaces). In nvme_mpath_add_disk, the first context acquires
the lock of subsystem and creates a head namespace, and other
contexts do nothing by checking GENHD_FL_UP of a head namespace
after waiting to acquire the lock. We verified the code with or
without multipathing using three vendors of dual-port NVMe SSDs.
Signed-off-by: Baegjae Sung <baegjae@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <keith.busch@intel.com>
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net> Tested-by: Matthias Ferdinand <bcache@mfedv.net> Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Coly Li [Tue, 27 Feb 2018 17:49:29 +0000 (09:49 -0800)]
bcache: correct flash only vols (check all uuids)
Commit 2831231d4c3f ("bcache: reduce cache_set devices iteration by
devices_max_used") adds c->devices_max_used to reduce iteration of
c->uuids elements, this value is updated in bcache_device_attach().
But for flash only volume, when calling flash_devs_run(), the function
bcache_device_attach() is not called yet and c->devices_max_used is not
updated. The unexpected result is, the flash only volume won't be run
by flash_devs_run().
This patch fixes the issue by iterate all c->uuids elements in
flash_devs_run(). c->devices_max_used will be updated properly when
bcache_device_attach() gets called.
[mlyle: commit subject edited for character limit]
Fixes: 2831231d4c3f ("bcache: reduce cache_set devices iteration by devices_max_used") Reported-by: Tang Junhui <tang.junhui@zte.com.cn> Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 12:01:42 +0000 (13:01 +0100)]
blockdev: Avoid two active bdev inodes for one device
When blkdev_open() races with device removal and creation it can happen
that unhashed bdev inode gets associated with newly created gendisk
like:
CPU0 CPU1
blkdev_open()
bdev = bd_acquire()
del_gendisk()
bdev_unhash_inode(bdev);
remove device
create new device with the same number
__blkdev_get()
disk = get_gendisk()
- gets reference to gendisk of the new device
Now another blkdev_open() will not find original 'bdev' as it got
unhashed, create a new one and associate it with the same 'disk' at
which point problems start as we have two independent page caches for
one device.
Fix the problem by verifying that the bdev inode didn't get unhashed
before we acquired gendisk reference. That way we make sure gendisk can
get associated only with visible bdev inodes.
Tested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 12:01:41 +0000 (13:01 +0100)]
genhd: Fix BUG in blkdev_open()
When two blkdev_open() calls for a partition race with device removal
and recreation, we can hit BUG_ON(!bd_may_claim(bdev, whole, holder)) in
blkdev_open(). The race can happen as follows:
blkdev_open(part1, O_EXCL) blkdev_open(part1, O_EXCL)
bdev = bd_acquire() bdev = bd_acquire()
blkdev_get(bdev)
bd_start_claiming(bdev)
- finds old inode 'whole'
bd_prepare_to_claim() -> 0
bdev_unhash_inode(whole);
<device removed>
<new device under same
number created>
blkdev_get(bdev);
bd_start_claiming(bdev)
- finds new inode 'whole'
bd_prepare_to_claim()
- this also succeeds as we have
different 'whole' here...
- bad things happen now as we
have two exclusive openers of
the same bdev
The problem here is that block device opens can see various intermediate
states while gendisk is shutting down and then being recreated.
We fix the problem by introducing new lookup_sem in gendisk that
synchronizes gendisk deletion with get_gendisk() and furthermore by
making sure that get_gendisk() does not return gendisk that is being (or
has been) deleted. This makes sure that once we ever manage to look up
newly created bdev inode, we are also guaranteed that following
get_gendisk() will either return failure (and we fail open) or it
returns gendisk for the new device and following bdget_disk() will
return new bdev inode (i.e., blkdev_open() follows the path as if it is
completely run after new device is created).
Reported-and-analyzed-by: Hou Tao <houtao1@huawei.com> Tested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 12:01:40 +0000 (13:01 +0100)]
genhd: Fix use after free in __blkdev_get()
When two blkdev_open() calls race with device removal and recreation,
__blkdev_get() can use looked up gendisk after it is freed:
CPU0 CPU1 CPU2
del_gendisk(disk);
bdev_unhash_inode(inode);
blkdev_open() blkdev_open()
bdev = bd_acquire(inode);
- creates and returns new inode
bdev = bd_acquire(inode);
- returns the same inode
__blkdev_get(devt) __blkdev_get(devt)
disk = get_gendisk(devt);
- got structure of device going away
<finish device removal>
<new device gets
created under the same
device number>
disk = get_gendisk(devt);
- got new device structure
if (!bdev->bd_openers) {
does the first open
}
if (!bdev->bd_openers)
- false
} else {
put_disk_and_module(disk)
- remember this was old device - this was last ref and disk is
now freed
}
disk_unblock_events(disk); -> oops
Fix the problem by making sure we drop reference to disk in
__blkdev_get() only after we are really done with it.
Reported-by: Hou Tao <houtao1@huawei.com> Tested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 12:01:38 +0000 (13:01 +0100)]
genhd: Rename get_disk() to get_disk_and_module()
Rename get_disk() to get_disk_and_module() to make sure what the
function does. It's not a great name but at least it is now clear that
put_disk() is not it's counterpart.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 12:01:37 +0000 (13:01 +0100)]
genhd: Fix leaked module reference for NVME devices
Commit 8ddcd653257c "block: introduce GENHD_FL_HIDDEN" added handling of
hidden devices to get_gendisk() but forgot to drop module reference
which is also acquired by get_disk(). Drop the reference as necessary.
Arguably the function naming here is misleading as put_disk() is *not*
the counterpart of get_disk() but let's fix that in the follow up
commit since that will be more intrusive.
Fixes: 8ddcd653257c18a669fcb75ee42c37054908e0d6 CC: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Mon, 26 Feb 2018 11:51:43 +0000 (12:51 +0100)]
direct-io: Fix sleep in atomic due to sync AIO
Commit e864f39569f4 "fs: add RWF_DSYNC aand RWF_SYNC" added additional
way for direct IO to become synchronous and thus trigger fsync from the
IO completion handler. Then commit 9830f4be159b "fs: Use RWF_* flags for
AIO operations" allowed these flags to be set for AIO as well. However
that commit forgot to update the condition checking whether the IO
completion handling should be defered to a workqueue and thus AIO DIO
with RWF_[D]SYNC set will call fsync() from IRQ context resulting in
sleep in atomic.
Fix the problem by checking directly iocb flags (the same way as it is
done in dio_complete()) instead of checking all conditions that could
lead to IO being synchronous.
CC: Christoph Hellwig <hch@lst.de> CC: Goldwyn Rodrigues <rgoldwyn@suse.com> CC: stable@vger.kernel.org Reported-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Fixes: 9830f4be159b29399d107bffb99e0132bc5aedd4 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jianchao Wang [Thu, 15 Feb 2018 11:13:41 +0000 (19:13 +0800)]
nvme-pci: Fix nvme queue cleanup if IRQ setup fails
This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes] Signed-off-by: Keith Busch <keith.busch@intel.com>
Ming Lei [Fri, 23 Feb 2018 15:36:57 +0000 (23:36 +0800)]
block: kyber: fix domain token leak during requeue
When requeuing request, the domain token should have been freed
before re-inserting the request to io scheduler. Otherwise, the
assigned domain token will be leaked, and IO hang can be caused.
Cc: Paolo Valente <paolo.valente@linaro.org> Cc: Omar Sandoval <osandov@fb.com> Cc: stable@vger.kernel.org Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kees Cook [Fri, 23 Feb 2018 00:59:26 +0000 (16:59 -0800)]
MIPS: boot: Define __ASSEMBLY__ for its.S build
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com> Fixes: 28128c61e08e ("kconfig.h: Include compiler types to avoid missed struct attributes") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 12 Feb 2018 21:18:38 +0000 (13:18 -0800)]
fs/signalfd: fix build error for BUS_MCEERR_AR
Fix build error in fs/signalfd.c by using same method that is used in
kernel/signal.c: separate blocks for different signal si_code values.
./fs/signalfd.c: error: 'BUS_MCEERR_AR' undeclared (first use in this function)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Linus Torvalds [Thu, 22 Feb 2018 20:13:01 +0000 (12:13 -0800)]
Merge tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
Linus Torvalds [Thu, 22 Feb 2018 20:05:43 +0000 (12:05 -0800)]
Merge tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a small number of staging and iio driver fixes for 4.16-rc2.
The IIO fixes are all for reported things, and the android driver
fixes also resolve some reported problems. The remaining fsl-mc
Kconfig change resolves a build testing error that Arnd reported.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: buffer: check if a buffer has been set up when poll is called
iio: adis_lib: Initialize trigger before requesting interrupt
staging: android: ion: Zero CMA allocated memory
staging: android: ashmem: Fix a race condition in pin ioctls
staging: fsl-mc: fix build testing on x86
iio: srf08: fix link error "devm_iio_triggered_buffer_setup" undefined
staging: iio: ad5933: switch buffer mode to software
iio: adc: stm32: fix stm32h7_adc_enable error handling
staging: iio: adc: ad7192: fix external frequency setting
iio: adc: aspeed: Fix error handling path
Linus Torvalds [Thu, 22 Feb 2018 20:04:05 +0000 (12:04 -0800)]
Merge tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.16-rc3.
There are some binder driver fixes to resolve reported issues in
stress testing the recent binder changes, some extcon driver fixes,
and a few mei driver fixes and new device ids.
All of these, with the exception of the mei driver id additions, have
been in linux-next for a while. I forgot to push out the mei driver id
additions to kernel.org until today, but all build tests pass with
them enabled"
* tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: me: add cannon point device ids for 4th device
mei: me: add cannon point device ids
mei: set device client to the disconnected state upon suspend.
ANDROID: binder: synchronize_rcu() when using POLLFREE.
binder: replace "%p" with "%pK"
ANDROID: binder: remove WARN() for redundant txn error
binder: check for binder_thread allocation failure in binder_poll()
extcon: int3496: process id-pin first so that we start with the right status
Revert "extcon: axp288: Redo charger type detection a couple of seconds after probe()"
extcon: axp288: Constify the axp288_pwr_up_down_info array
Linus Torvalds [Thu, 22 Feb 2018 19:57:39 +0000 (11:57 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"Nothing in this is overly interesting, it's mostly your garden variety
fixes.
There was some work in this merge cycle around the new ioctl kABI, so
there are fixes in here related to that (probably with more to come).
We've also recently added new netlink support with a goal of moving
the primary means of configuring the entire subsystem to netlink
(eventually, this is a long term project), so there are fixes for
that.
Then a few bnxt_re driver fixes, and a few minor WARN_ON removals, and
that covers this pull request. There are already a few more fixes on
the list as of this morning, so there will certainly be more to come
in this rc cycle ;-)
Summary:
- Lots of fixes for the new IOCTL interface and general uverbs flow.
Found through testing and syzkaller
- Bugfixes for the new resource track netlink reporting
- Remove some unneeded WARN_ONs that were triggering for some users
in IPoIB
- Various fixes for the bnxt_re driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (27 commits)
RDMA/uverbs: Fix kernel panic while using XRC_TGT QP type
RDMA/bnxt_re: Avoid system hang during device un-reg
RDMA/bnxt_re: Fix system crash during load/unload
RDMA/bnxt_re: Synchronize destroy_qp with poll_cq
RDMA/bnxt_re: Unpin SQ and RQ memory if QP create fails
RDMA/bnxt_re: Disable atomic capability on bnxt_re adapters
RDMA/restrack: don't use uaccess_kernel()
RDMA/verbs: Check existence of function prior to accessing it
RDMA/vmw_pvrdma: Fix usage of user response structures in ABI file
RDMA/uverbs: Sanitize user entered port numbers prior to access it
RDMA/uverbs: Fix circular locking dependency
RDMA/uverbs: Fix bad unlock balance in ib_uverbs_close_xrcd
RDMA/restrack: Increment CQ restrack object before committing
RDMA/uverbs: Protect from command mask overflow
IB/uverbs: Fix unbalanced unlock on error path for rdma_explicit_destroy
IB/uverbs: Improve lockdep_check
RDMA/uverbs: Protect from races between lookup and destroy of uobjects
IB/uverbs: Hold the uobj write lock after allocate
IB/uverbs: Fix possible oops with duplicate ioctl attributes
IB/uverbs: Add ioctl support for 32bit processes
...
Linus Torvalds [Thu, 22 Feb 2018 19:53:17 +0000 (11:53 -0800)]
Merge tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V cleanups from Palmer Dabbelt:
"This contains a handful of small cleanups.
The only functional change is that IRQs are now enabled during
exception handling, which was found when some warnings triggered with
`CONFIG_DEBUG_ATOMIC_SLEEP=y`.
The remaining fixes should have no functional change: `sbi_save()` has
been renamed to `parse_dtb()` reflect what it actually does, and a
handful of unused Kconfig entries have been removed"
* tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
Rename sbi_save to parse_dtb to improve code readability
RISC-V: Enable IRQ during exception handling
riscv: Remove ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select
riscv: kconfig: Remove RISCV_IRQ_INTC select
riscv: Remove ARCH_WANT_OPTIONAL_GPIOLIB select
Linus Torvalds [Thu, 22 Feb 2018 18:45:46 +0000 (10:45 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: don't defer struct page initialization for Xen pv guests
lib/Kconfig.debug: enable RUNTIME_TESTING_MENU
vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems
selftests/memfd: add run_fuse_test.sh to TEST_FILES
bug.h: work around GCC PR82365 in BUG()
mm/swap.c: make functions and their kernel-doc agree (again)
mm/zpool.c: zpool_evictable: fix mismatch in parameter name and kernel-doc
ida: do zeroing in ida_pre_get()
mm, swap, frontswap: fix THP swap if frontswap enabled
certs/blacklist_nohashes.c: fix const confusion in certs blacklist
kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE
mm, mlock, vmscan: no more skipping pagevecs
mm: memcontrol: fix NR_WRITEBACK leak in memcg and system stats
Kbuild: always define endianess in kconfig.h
include/linux/sched/mm.h: re-inline mmdrop()
tools: fix cross-compile var clobbering
Luck, Tony [Thu, 22 Feb 2018 17:15:06 +0000 (09:15 -0800)]
efivarfs: Limit the rate for non-root to read files
Each read from a file in efivarfs results in two calls to EFI
(one to get the file size, another to get the actual data).
On X86 these EFI calls result in broadcast system management
interrupts (SMI) which affect performance of the whole system.
A malicious user can loop performing reads from efivarfs bringing
the system to its knees.
Linus suggested per-user rate limit to solve this.
So we add a ratelimit structure to "user_struct" and initialize
it for the root user for no limit. When allocating user_struct for
other users we set the limit to 100 per second. This could be used
for other places that want to limit the rate of some detrimental
user action.
In efivarfs if the limit is exceeded when reading, we take an
interruptible nap for 50ms and check the rate limit again.
Kees Cook [Thu, 22 Feb 2018 17:41:40 +0000 (09:41 -0800)]
kconfig.h: Include compiler types to avoid missed struct attributes
The header files for some structures could get included in such a way
that struct attributes (specifically __randomize_layout from path.h) would
be parsed as variable names instead of attributes. This could lead to
some instances of a structure being unrandomized, causing nasty GPFs, etc.
This patch makes sure the compiler_types.h header is included in
kconfig.h so that we've always got types and struct attributes defined,
since kconfig.h is included from the compiler command line.
Reported-by: Patrick McLean <chutzpah@gentoo.org> Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Fixes: 3859a271a003 ("randstruct: Mark various structs for randomization") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H.J. Lu [Wed, 7 Feb 2018 22:20:09 +0000 (14:20 -0800)]
x86: Treat R_X86_64_PLT32 as R_X86_64_PC32
On i386, there are 2 types of PLTs, PIC and non-PIC. PIE and shared
objects must use PIC PLT. To use PIC PLT, you need to load
_GLOBAL_OFFSET_TABLE_ into EBX first. There is no need for that on
x86-64 since x86-64 uses PC-relative PLT.
On x86-64, for 32-bit PC-relative branches, we can generate PLT32
relocation, instead of PC32 relocation, which can also be used as
a marker for 32-bit PC-relative branches. Linker can always reduce
PLT32 relocation to PC32 if function is defined locally. Local
functions should use PC32 relocation. As far as Linux kernel is
concerned, R_X86_64_PLT32 can be treated the same as R_X86_64_PC32
since Linux kernel doesn't use PLT.
R_X86_64_PLT32 for 32-bit PC-relative branches has been enabled in
binutils master branch which will become binutils 2.31.
[ hjl is working on having better documentation on this all, but a few
more notes from him:
"PLT32 relocation is used as marker for PC-relative branches. Because
of EBX, it looks odd to generate PLT32 relocation on i386 when EBX
doesn't have GOT.
As for symbol resolution, PLT32 and PC32 relocations are almost
interchangeable. But when linker sees PLT32 relocation against a
protected symbol, it can resolved locally at link-time since it is
used on a branch instruction. Linker can't do that for PC32
relocation"
but for the kernel use, the two are basically the same, and this
commit gets things building and working with the current binutils
master - Linus ]
Signed-off-by: H.J. Lu <hjl.tools@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nvme-fabrics: don't check for non-NULL module in nvmf_register_transport
THIS_MODULE evaluates to NULL when used from code built into the kernel,
thus breaking built-in transport modules. Remove the bogus check.
Fixes: 0de5cd36 ("nvme-fabrics: protect against module unload during create_ctrl") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Keith Busch <keith.busch@intel.com>
Juergen Gross [Wed, 21 Feb 2018 22:46:09 +0000 (14:46 -0800)]
mm: don't defer struct page initialization for Xen pv guests
Commit f7f99100d8d9 ("mm: stop zeroing memory during allocation in
vmemmap") broke Xen pv domains in some configurations, as the "Pinned"
information in struct page of early page tables could get lost.
This will lead to the kernel trying to write directly into the page
tables instead of asking the hypervisor to do so. The result is a crash
like the following:
Avoid this problem by not deferring struct page initialization when
running as Xen pv guest.
Pavel said:
: This is unique for Xen, so this particular issue won't effect other
: configurations. I am going to investigate if there is a way to
: re-enable deferred page initialization on xen guests.
[akpm@linux-foundation.org: explicitly include xen.h] Link: http://lkml.kernel.org/r/20180216154101.22865-1-jgross@suse.com Fixes: f7f99100d8d95d ("mm: stop zeroing memory during allocation in vmemmap") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Steven Sistare <steven.sistare@oracle.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Bob Picco <bob.picco@oracle.com> Cc: <stable@vger.kernel.org> [4.15.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anders Roxell [Wed, 21 Feb 2018 22:46:05 +0000 (14:46 -0800)]
lib/Kconfig.debug: enable RUNTIME_TESTING_MENU
Commit d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to ease
disabling it all") causes a regression when using runtime tests due to
it defaults RUNTIME_TESTING_MENU to not set.
Link: http://lkml.kernel.org/r/20180214133015.10090-1-anders.roxell@linaro.org Fixes: d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to easedisabling it all") Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Cc: Vincent Legoll <vincent.legoll@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Byungchul Park <byungchul.park@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Wed, 21 Feb 2018 22:46:01 +0000 (14:46 -0800)]
vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems
Kai Heng Feng has noticed that BUG_ON(PageHighMem(pg)) triggers in
drivers/media/common/saa7146/saa7146_core.c since 19809c2da28a ("mm,
vmalloc: use __GFP_HIGHMEM implicitly").
saa7146_vmalloc_build_pgtable uses vmalloc_32 and it is reasonable to
expect that the resulting page is not in highmem. The above commit
aimed to add __GFP_HIGHMEM only for those requests which do not specify
any zone modifier gfp flag. vmalloc_32 relies on GFP_VMALLOC32 which
should do the right thing. Except it has been missed that GFP_VMALLOC32
is an alias for GFP_KERNEL on 32b architectures. Thanks to Matthew to
notice this.
Fix the problem by unconditionally setting GFP_DMA32 in GFP_VMALLOC32
for !64b arches (as a bailout). This should do the right thing and use
ZONE_NORMAL which should be always below 4G on 32b systems.
Debugged by Matthew Wilcox.
[akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/20180212095019.GX21609@dhcp22.suse.cz Fixes: 19809c2da28a ("mm, vmalloc: use __GFP_HIGHMEM implicitly”) Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Kai Heng Feng <kai.heng.feng@canonical.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Laura Abbott <labbott@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 21 Feb 2018 22:45:54 +0000 (14:45 -0800)]
bug.h: work around GCC PR82365 in BUG()
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365 Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Christopher Li <sparse@chrisli.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Wed, 21 Feb 2018 22:45:50 +0000 (14:45 -0800)]
mm/swap.c: make functions and their kernel-doc agree (again)
There was a conflict between the commit e02a9f048ef7 ("mm/swap.c: make
functions and their kernel-doc agree") and the commit f144c390f905 ("mm:
docs: fix parameter names mismatch") that both tried to fix mismatch
betweeen pagevec_lookup_entries() parameter names and their description.
Since nr_entries is a better name for the parameter, fix the description
again.
Link: http://lkml.kernel.org/r/1518116946-20947-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Wed, 21 Feb 2018 22:45:43 +0000 (14:45 -0800)]
ida: do zeroing in ida_pre_get()
As far as I can tell, the only place the per-cpu ida_bitmap is populated
is in ida_pre_get. The pre-allocated element is stolen in two places in
ida_get_new_above, in both cases immediately followed by a memset(0).
Since ida_get_new_above is called with locks held, do the zeroing in
ida_pre_get, or rather let kmalloc() do it. Also, apparently gcc
generates ~44 bytes of code to do a memset(, 0, 128):
$ scripts/bloat-o-meter vmlinux.{0,1}
add/remove: 0/0 grow/shrink: 2/1 up/down: 5/-88 (-83)
Function old new delta
ida_pre_get 115 119 +4
vermagic 27 28 +1
ida_get_new_above 715 627 -88
Link: http://lkml.kernel.org/r/20180108225634.15340-1-linux@rasmusvillemoes.dk Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Matthew Wilcox <mawilcox@microsoft.com> Cc: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Wed, 21 Feb 2018 22:45:39 +0000 (14:45 -0800)]
mm, swap, frontswap: fix THP swap if frontswap enabled
It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,
After bisection, it was found the first bad commit is bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").
The root cause is as follows:
When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance. But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved. After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.
This is fixed by refusing to save page in the frontswap store functions
if the page is a THP. So that the THP will be swapped out to swap
device.
Another choice is to split THP if frontswap is enabled. But it is found
that the frontswap enabling isn't flexible. For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.
Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.
Link: http://lkml.kernel.org/r/20180209084947.22749-1-ying.huang@intel.com Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out") Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Suggested-by: Minchan Kim <minchan@kernel.org> [put THP checking in backend] Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Shaohua Li <shli@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Shakeel Butt <shakeelb@google.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: <stable@vger.kernel.org> [4.14] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shakeel Butt [Wed, 21 Feb 2018 22:45:28 +0000 (14:45 -0800)]
mm, mlock, vmscan: no more skipping pagevecs
When a thread mlocks an address space backed either by file pages which
are currently not present in memory or swapped out anon pages (not in
swapcache), a new page is allocated and added to the local pagevec
(lru_add_pvec), I/O is triggered and the thread then sleeps on the page.
On I/O completion, the thread can wake on a different CPU, the mlock
syscall will then sets the PageMlocked() bit of the page but will not be
able to put that page in unevictable LRU as the page is on the pagevec
of a different CPU. Even on drain, that page will go to evictable LRU
because the PageMlocked() bit is not checked on pagevec drain.
The page will eventually go to right LRU on reclaim but the LRU stats
will remain skewed for a long time.
This patch puts all the pages, even unevictable, to the pagevecs and on
the drain, the pages will be added on their LRUs correctly by checking
their evictability. This resolves the mlocked pages on pagevec of other
CPUs issue because when those pagevecs will be drained, the mlocked file
pages will go to unevictable LRU. Also this makes the race with munlock
easier to resolve because the pagevec drains happen in LRU lock.
However there is still one place which makes a page evictable and does
PageLRU check on that page without LRU lock and needs special attention.
TestClearPageMlocked() and isolate_lru_page() in clear_page_mlock().
#0: __pagevec_lru_add_fn #1: clear_page_mlock
SetPageLRU() if (!TestClearPageMlocked())
return
smp_mb() // <--required
// inside does PageLRU
if (!PageMlocked()) if (isolate_lru_page())
move to evictable LRU putback_lru_page()
else
move to unevictable LRU
In '#1', TestClearPageMlocked() provides full memory barrier semantics
and thus the PageLRU check (inside isolate_lru_page) can not be
reordered before it.
In '#0', without explicit memory barrier, the PageMlocked() check can be
reordered before SetPageLRU(). If that happens, '#0' can put a page in
unevictable LRU and '#1' might have just cleared the Mlocked bit of that
page but fails to isolate as PageLRU fails as '#0' still hasn't set
PageLRU bit of that page. That page will be stranded on the unevictable
LRU.
There is one (good) side effect though. Without this patch, the pages
allocated for System V shared memory segment are added to evictable LRUs
even after shmctl(SHM_LOCK) on that segment. This patch will correctly
put such pages to unevictable LRU.
Link: http://lkml.kernel.org/r/20171121211241.18877-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Greg Thelen <gthelen@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Shaohua Li <shli@fb.com> Cc: Jan Kara <jack@suse.cz> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Wed, 21 Feb 2018 22:45:24 +0000 (14:45 -0800)]
mm: memcontrol: fix NR_WRITEBACK leak in memcg and system stats
After commit a983b5ebee57 ("mm: memcontrol: fix excessive complexity in
memory.stat reporting"), we observed slowly upward creeping NR_WRITEBACK
counts over the course of several days, both the per-memcg stats as well
as the system counter in e.g. /proc/meminfo.
The conversion from full per-cpu stat counts to per-cpu cached atomic
stat counts introduced an irq-unsafe RMW operation into the updates.
Most stat updates come from process context, but one notable exception
is the NR_WRITEBACK counter. While writebacks are issued from process
context, they are retired from (soft)irq context.
When writeback completions interrupt the RMW counter updates of new
writebacks being issued, the decs from the completions are lost.
Since the global updates are routed through the joint lruvec API, both
the memcg counters as well as the system counters are affected.
This patch makes the joint stat and event API irq safe.
Link: http://lkml.kernel.org/r/20180203082353.17284-1-hannes@cmpxchg.org Fixes: a983b5ebee57 ("mm: memcontrol: fix excessive complexity in memory.stat reporting") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Debugged-by: Tejun Heo <tj@kernel.org> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 21 Feb 2018 22:45:20 +0000 (14:45 -0800)]
Kbuild: always define endianess in kconfig.h
Build testing with LTO found a couple of files that get compiled
differently depending on whether asm/byteorder.h gets included early
enough or not. In particular, include/asm-generic/qrwlock_types.h is
affected by this, but there are probably others as well.
The symptom is a series of LTO link time warnings, including these:
net/netlabel/netlabel_unlabeled.h:223: error: type of 'netlbl_unlhsh_add' does not match original declaration [-Werror=lto-type-mismatch]
int netlbl_unlhsh_add(struct net *net,
net/netlabel/netlabel_unlabeled.c:377: note: 'netlbl_unlhsh_add' was previously declared here
include/net/ipv6.h:360: error: type of 'ipv6_renew_options_kern' does not match original declaration [-Werror=lto-type-mismatch]
ipv6_renew_options_kern(struct sock *sk,
net/ipv6/exthdrs.c:1162: note: 'ipv6_renew_options_kern' was previously declared here
net/core/dev.c:761: note: 'dev_get_by_name_rcu' was previously declared here
struct net_device *dev_get_by_name_rcu(struct net *net, const char *name)
net/core/dev.c:761: note: code may be misoptimized unless -fno-strict-aliasing is used
drivers/gpu/drm/i915/i915_drv.h:3377: error: type of 'i915_gem_object_set_to_wc_domain' does not match original declaration [-Werror=lto-type-mismatch]
i915_gem_object_set_to_wc_domain(struct drm_i915_gem_object *obj, bool write);
drivers/gpu/drm/i915/i915_gem.c:3639: note: 'i915_gem_object_set_to_wc_domain' was previously declared here
include/linux/debugfs.h:92:9: error: type of 'debugfs_attr_read' does not match original declaration [-Werror=lto-type-mismatch]
ssize_t debugfs_attr_read(struct file *file, char __user *buf,
fs/debugfs/file.c:318: note: 'debugfs_attr_read' was previously declared here
include/linux/rwlock_api_smp.h:30: error: type of '_raw_read_unlock' does not match original declaration [-Werror=lto-type-mismatch]
void __lockfunc _raw_read_unlock(rwlock_t *lock) __releases(lock);
kernel/locking/spinlock.c:246:26: note: '_raw_read_unlock' was previously declared here
include/linux/fs.h:3308:5: error: type of 'simple_attr_open' does not match original declaration [-Werror=lto-type-mismatch]
int simple_attr_open(struct inode *inode, struct file *file,
fs/libfs.c:795: note: 'simple_attr_open' was previously declared here
All of the above are caused by include/asm-generic/qrwlock_types.h
failing to include asm/byteorder.h after commit e0d02285f16e
("locking/qrwlock: Use 'struct qrwlock' instead of 'struct __qrwlock'")
in linux-4.15.
Similar bugs may or may not exist in older kernels as well, but there is
no easy way to test those with link-time optimizations, and kernels
before 4.14 are harder to fix because they don't have Babu's patch
series
We had similar issues with CONFIG_ symbols in the past and ended up
always including the configuration headers though linux/kconfig.h. This
works around the issue through that same file, defining either
__BIG_ENDIAN or __LITTLE_ENDIAN depending on CONFIG_CPU_BIG_ENDIAN,
which is now always set on all architectures since commit 4c97a0c8fee3
("arch: define CPU_BIG_ENDIAN for all fixed big endian archs").
Link: http://lkml.kernel.org/r/20180202154104.1522809-2-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Babu Moger <babu.moger@amd.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Nicolas Pitre <nico@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Martin Kelly [Wed, 21 Feb 2018 22:45:12 +0000 (14:45 -0800)]
tools: fix cross-compile var clobbering
Currently a number of Makefiles break when used with toolchains that
pass extra flags in CC and other cross-compile related variables (such
as --sysroot).
Thus we get this error when we use a toolchain that puts --sysroot in
the CC var:
~/src/linux/tools$ make iio
[snip]
iio_event_monitor.c:18:10: fatal error: unistd.h: No such file or directory
#include <unistd.h>
^~~~~~~~~~
This occurs because we clobber several env vars related to
cross-compiling with lines like this:
CC = $(CROSS_COMPILE)gcc
Although this will point to a valid cross-compiler, we lose any extra
flags that might exist in the CC variable, which can break toolchains
that rely on them (for example, those that use --sysroot).
Although arm-poky-linux-gnueabi-gcc is a cross-compiler, we've lost the
--sysroot and other flags that enable us to find the right libraries to
link against, so we can't find unistd.h and other libraries and headers.
Normally with the --sysroot flag we would find unistd.h in the sdk
directory in the sysroot:
The perf Makefile adds CC = $(CROSS_COMPILE)gcc if and only if CC is not
already set, and it compiles correctly with the above toolchain.
So, generalize the logic that perf uses in the common Makefile and
remove the manual CC = $(CROSS_COMPILE)gcc lines from each Makefile.
Note that this patch does not fix cross-compile for all the tools (some
have other bugs), but it does fix it for all except usb and acpi, which
still have other unrelated issues.
I tested both with and without the patch on native and cross-build and
there appear to be no regressions.
Link: http://lkml.kernel.org/r/20180107214028.23771-1-martin@martingkelly.com Signed-off-by: Martin Kelly <martin@martingkelly.com> Acked-by: Mark Brown <broonie@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Pali Rohar <pali.rohar@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Robert Moore <robert.moore@intel.com> Cc: Lv Zheng <lv.zheng@intel.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Valentina Manea <valentina.manea.m@gmail.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leon Romanovsky [Wed, 21 Feb 2018 08:25:01 +0000 (10:25 +0200)]
RDMA/uverbs: Fix kernel panic while using XRC_TGT QP type
Attempt to modify XRC_TGT QP type from the user space (ibv_xsrq_pingpong
invocation) will trigger the following kernel panic. It is caused by the
fact that such QPs missed uobject initialization.
Palmer Dabbelt [Tue, 20 Feb 2018 18:51:19 +0000 (10:51 -0800)]
RISC-V: kconfig cleanups
These three kconfig cleanups were found by ulfalyzer. They're all
things we were selecting that were undefined, either because they'd been
remove upstream or are part of a future RISC-V submission.
* ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE is obselete.
* RISCV_IRQ_INTC is the old name for our interrupt controller driver,
it'll be changed for the final submission and doesn't exist now.
* ARCH_WANT_OPTIONAL_GPIOLIB is obselete.
Ulf Magnusson [Mon, 5 Feb 2018 01:21:19 +0000 (02:21 +0100)]
riscv: Remove ARCH_WANT_OPTIONAL_GPIOLIB select
The ARCH_WANT_OPTIONAL_GPIOLIB symbol was removed in commit 65053e1a7743
("gpio: delete ARCH_[WANTS_OPTIONAL|REQUIRE]_GPIOLIB"). GPIOLIB should
just be selected explicitly if needed.
Remove the ARCH_WANT_OPTIONAL_GPIOLIB select from RISCV.
See commit 0145071b3314 ("x86: Do away with
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB") and commit da9a1c6767 ("arm64: do
away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB") as well.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Linus Torvalds [Tue, 20 Feb 2018 18:05:02 +0000 (10:05 -0800)]
Merge tag 'leds_for-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED maintainer update:
"LED update to MAINTAINERS, to admit the reality.
Message from Richard:
"I've been looking at some of the emails but not needed to be
involved for a while now, you're doing fine without me!" [0]
Many thanks to Richard for his work as a founder of the LED
subsystem!"
[0] https://lkml.org/lkml/2018/2/18/145
* tag 'leds_for-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Remove Richard Purdie from LED maintainers
Selvin Xavier [Fri, 16 Feb 2018 05:20:13 +0000 (21:20 -0800)]
RDMA/bnxt_re: Avoid system hang during device un-reg
BNXT_RE_FLAG_TASK_IN_PROG doesn't handle multiple work
requests posted together. Track schedule of multiple
workqueue items by maintaining a per device counter
and proceed with IB dereg only if this counter is zero.
flush_workqueue is no longer required from
NETDEV_UNREGISTER path.
Selvin Xavier [Fri, 16 Feb 2018 05:20:12 +0000 (21:20 -0800)]
RDMA/bnxt_re: Fix system crash during load/unload
During driver unload, the driver proceeds with cleanup
without waiting for the scheduled events. So the device
pointers get freed up and driver crashes when the events
are scheduled later.
Flush the bnxt_re_task work queue before starting
device removal.
commit dbac5d07d13e ("usb: musb: host: don't start next rx urb if current one failed")
along with commit b5801212229f ("usb: musb: host: clear rxcsr error bit if set")
try to solve the issue described in [1], but the latter alone is
sufficient, and the former causes the issue as in [2], so now revert it.
Andreas Kemnade [Tue, 20 Feb 2018 13:30:10 +0000 (07:30 -0600)]
usb: musb: fix enumeration after resume
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87cb3 ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'iio-fixes-for-4.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.16 cycle.
One nasty very old crash around polling for buffers that aren't there
- though that can only cause effects on drivers that support events
but not buffers.
* buffer / kfifo handling in the core.
- Check there is a buffer and return 0 from poll directly if there
isn't. Poll doesn't make sense in this circumstances, but best to close
the hole.
* ad5933
- Change the marked buffer mode to a software buffer as the meaning of
the hardware buffer label has long since changed and this uses a front
end software buffer anyway.
* ad7192
- Fix the fact the external clock frequency was only set when using the
internal clock which was less than helpful.
* adis_lib
- Initialize the trigger before requesting the interrupt. Some newer
parts can power up with interrupt generation enabled so ordering now
matters.
* aspeed-adc
- Fix an errror handling path as labels and general ordering were wrong.
* srf08
- Fix a link error due to undefined devm_iio_triggered_buffer_setup.
* stm32-adc
- Fix error handling unwind squence in stm32h7_adc_enable.
Merge tag 'extcon-fixes-for-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
Update extcon for v4.16-rc3
This patch fixes issue of X-power extcon-axp288 and Intel extcon-int3496 driver.
- For extcon-int3496 driver,
Process id-pin first so that we start with the right status in order to fix
a race where the initial work might still be running while other drivers
were already calling extcon_get_state().
- For extcon-axp288 driver,
Revert the patch[1] which were applied to v4.16-rc1 because there are better
ways with usb-role-switch and constify the axp288_pwr_up_down_info array.
[1] 60ed99961469a3 ("extcon: axp288: Redo charger type detection a couple of seconds after probe()")
1) Prevent index integer overflow in ptr_ring, from Jason Wang.
2) Program mvpp2 multicast filter properly, from Mikulas Patocka.
3) The bridge brport attribute file is write only and doesn't have a
->show() method, don't blindly invoke it. From Xin Long.
4) Inverted mask used in genphy_setup_forced(), from Ingo van Lil.
5) Fix multiple definition issue with if_ether.h UAPI header, from
Hauke Mehrtens.
6) Fix GFP_KERNEL usage in atomic in RDS protocol code, from Sowmini
Varadhan.
7) Revert XDP redirect support from thunderx driver, it is not
implemented properly. From Jesper Dangaard Brouer.
8) Fix missing RTNL protection across some tipc operations, from Ying
Xue.
9) Return the correct IV bytes in the TLS getsockopt code, from Boris
Pismenny.
10) Take tclassid into consideration properly when doing FIB rule
matching. From Stefano Brivio.
11) cxgb4 device needs more PCI VPD quirks, from Casey Leedom.
12) TUN driver doesn't align frags properly, and we can end up doing
unaligned atomics on misaligned metadata. From Eric Dumazet.
13) Fix various crashes found using DEBUG_PREEMPT in rmnet driver, from
Subash Abhinov Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
tg3: APE heartbeat changes
mlxsw: spectrum_router: Do not unconditionally clear route offload indication
net: qualcomm: rmnet: Fix possible null dereference in command processing
net: qualcomm: rmnet: Fix warning seen with 64 bit stats
net: qualcomm: rmnet: Fix crash on real dev unregistration
sctp: remove the left unnecessary check for chunk in sctp_renege_events
rxrpc: Work around usercopy check
tun: fix tun_napi_alloc_frags() frag allocator
udplite: fix partial checksum initialization
skbuff: Fix comment mis-spelling.
dn_getsockoptdecnet: move nf_{get/set}sockopt outside sock lock
PCI/cxgb4: Extend T3 PCI quirk to T4+ devices
cxgb4: fix trailing zero in CIM LA dump
cxgb4: free up resources of pf 0-3
fib_semantics: Don't match route with mismatching tclassid
NFC: llcp: Limit size of SDP URI
tls: getsockopt return record sequence number
tls: reset the crypto info if copy_from_user fails
tls: retrun the correct IV in getsockopt
docs: segmentation-offloads.txt: add SCTP info
...
Jacek Anaszewski [Sun, 18 Feb 2018 20:11:25 +0000 (21:11 +0100)]
MAINTAINERS: Remove Richard Purdie from LED maintainers
Richard has been inactive on the linux-leds list for a long time.
After email discussion we agreed on removing him from
the LED maintainers, which will better reflect the actual status.
Acked-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com> Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 16 Feb 2018 23:30:44 +0000 (00:30 +0100)]
mlxsw: spectrum_router: Do not unconditionally clear route offload indication
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89fe7 ("mlxsw: spectrum_router: Provide offload indication using nexthop flags") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Tested-by: Alexander Petrovskiy <alexpe@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Fix possible null dereference in command processing
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c45760 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 192c4b5d48f2 ("net: qualcomm: rmnet: Add support for 64 bit stats") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Fix crash on real dev unregistration
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
Linus Torvalds [Sun, 18 Feb 2018 20:56:41 +0000 (12:56 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Linus Torvalds [Sun, 18 Feb 2018 20:38:40 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Linus Torvalds [Sat, 17 Feb 2018 18:20:47 +0000 (10:20 -0800)]
Merge tag 'for-linus-20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
Linus Torvalds [Sat, 17 Feb 2018 18:08:28 +0000 (10:08 -0800)]
Merge tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
Linus Torvalds [Sat, 17 Feb 2018 18:06:13 +0000 (10:06 -0800)]
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
Linus Torvalds [Sat, 17 Feb 2018 17:48:26 +0000 (09:48 -0800)]
Merge tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
Linus Torvalds [Sat, 17 Feb 2018 17:46:18 +0000 (09:46 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
Linus Torvalds [Sat, 17 Feb 2018 17:16:09 +0000 (09:16 -0800)]
Merge tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
iio: buffer: check if a buffer has been set up when poll is called
If no iio buffer has been set up and poll is called return 0.
Without this check there will be a null pointer dereference when
calling poll on a iio driver without an iio buffer.
Cc: stable@vger.kernel.org Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt@axis.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adis_lib: Initialize trigger before requesting interrupt
The adis_probe_trigger() creates a new IIO trigger and requests an
interrupt associated with the trigger. The interrupt uses the generic
iio_trigger_generic_data_rdy_poll() function as its interrupt handler.
Currently the driver initializes some fields of the trigger structure after
the interrupt has been requested. But an interrupt can fire as soon as it
has been requested. This opens up a race condition.
iio_trigger_generic_data_rdy_poll() will access the trigger data structure
and dereference the ops field. If the ops field is not yet initialized this
will result in a NULL pointer deref.
It is not expected that the device generates an interrupt at this point, so
typically this issue did not surface unless e.g. due to a hardware
misconfiguration (wrong interrupt number, wrong polarity, etc.).
But some newer devices from the ADIS family start to generate periodic
interrupts in their power-on reset configuration and unfortunately the
interrupt can not be masked in the device. This makes the race condition
much more visible and the following crash has been observed occasionally
when booting a system using the ADIS16460.
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-04126-gf9739f0-dirty #257
Hardware name: Xilinx Zynq Platform
task: ef04f640 task.stack: ef050000
PC is at iio_trigger_notify_done+0x30/0x68
LR is at iio_trigger_generic_data_rdy_poll+0x18/0x20
pc : [<c042d868>] lr : [<c042d924>] psr: 60000193
sp : ef051bb8 ip : 00000000 fp : ef106400
r10: c081d80a r9 : ef3bfa00 r8 : 00000087
r7 : ef051bec r6 : 00000000 r5 : ef3bfa00 r4 : ee92ab00
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : ee97e400
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xef050210)
[<c042d868>] (iio_trigger_notify_done) from [<c0065b10>] (__handle_irq_event_percpu+0x88/0x118)
[<c0065b10>] (__handle_irq_event_percpu) from [<c0065bbc>] (handle_irq_event_percpu+0x1c/0x58)
[<c0065bbc>] (handle_irq_event_percpu) from [<c0065c30>] (handle_irq_event+0x38/0x5c)
[<c0065c30>] (handle_irq_event) from [<c0068e28>] (handle_level_irq+0xa4/0x130)
[<c0068e28>] (handle_level_irq) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c021ab7c>] (zynq_gpio_irqhandler+0xb8/0x13c)
[<c021ab7c>] (zynq_gpio_irqhandler) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c0065370>] (__handle_domain_irq+0x5c/0xb4)
[<c0065370>] (__handle_domain_irq) from [<c000940c>] (gic_handle_irq+0x48/0x8c)
[<c000940c>] (gic_handle_irq) from [<c0013e8c>] (__irq_svc+0x6c/0xa8)
To fix this make sure that the trigger is fully initialized before
requesting the interrupt.
Fixes: ccd2b52f4ac6 ("staging:iio: Add common ADIS library") Reported-by: Robin Getz <Robin.Getz@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pvcalls-front: introduce a per sock_mapping refcount
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Joao Martins [Fri, 2 Feb 2018 17:42:33 +0000 (17:42 +0000)]
xenbus: track caller request id
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Robin Murphy [Fri, 16 Feb 2018 17:04:23 +0000 (17:04 +0000)]
arm64: cputype: Silence Sparse warnings
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Xin Long [Fri, 16 Feb 2018 09:18:33 +0000 (17:18 +0800)]
sctp: remove the left unnecessary check for chunk in sctp_renege_events
Commit fb23403536ea ("sctp: remove the useless check in
sctp_renege_events") forgot to remove another check for
chunk in sctp_renege_events.
Dan found this when doing a static check.
This patch is to remove that check, and also to merge
two checks into one 'if statement'.
Fixes: fb23403536ea ("sctp: remove the useless check in sctp_renege_events") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 15 Feb 2018 22:59:00 +0000 (22:59 +0000)]
rxrpc: Work around usercopy check
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 15 Feb 2018 22:47:15 +0000 (14:47 -0800)]
tun: fix tun_napi_alloc_frags() frag allocator
<Mark Rutland reported>
While fuzzing arm64 v4.16-rc1 with Syzkaller, I've been hitting a
misaligned atomic in __skb_clone:
atomic_inc(&(skb_shinfo(skb)->dataref));
where dataref doesn't have the required natural alignment, and the
atomic operation faults. e.g. i often see it aligned to a single
byte boundary rather than a four byte boundary.
AFAICT, the skb_shared_info is misaligned at the instant it's
allocated in __napi_alloc_skb() __napi_alloc_skb()
</end of report>
Problem is caused by tun_napi_alloc_frags() using
napi_alloc_frag() with user provided seg sizes,
leading to other users of this API getting unaligned
page fragments.
Since we would like to not necessarily add paddings or alignments to
the frags that tun_napi_alloc_frags() attaches to the skb, switch to
another page frag allocator.
As a bonus skb_page_frag_refill() can use GFP_KERNEL allocations,
meaning that we can not deplete memory reserves as easily.
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log