drm/msm/disp/dpu1: increase the range of interrupts in dpu_irq_map
Currently, each register in the dpu interrupt set is allowed
to have a maximum of 32 interrupts. With the introduction
of INTF_5_VSYNC and INTF_5_UNDERRUN irqs for EDP panel,
the total number of interrupts under INTR_STATUS register
in dpu_irq_map will exceed 32. Increase the range of each
interrupt register to 64 to handle this.
This patch has dependency on the below series:
https://patchwork.kernel.org/project/linux-arm-msm/list/?series=461193
drm/msm/disp/dpu1: enable DATA_HCTL_EN for sc7280 target
The reset value of INTF_CONFIG2 register is changed
for SC7280 family. Changes are added to program
this register correctly based on the target.
DATA_HCTL_EN in INTF_CONFIG2 register allows data
to be transferred at a different rate than video
timing. When this is set, the number of data per
line follows DISPLAY_DATA_HCTL register value.
This change adds support to program these
registers for sc7280 target.
drm/msm/disp/dpu1: add support to program fetch active in ctl path
A new register called CTL_FETCH_ACTIVE is introduced in
SC7280 family which is used to inform the HW about
the pipes which are active in the current ctl path.
This change adds support to program this register
based on the active pipes in the current composition.
drm/msm/disp/dpu1: add intf offsets for SC7280 target
Interface block offsets are different for SC7280 family
when compared to existing targets. These offset values
are used to access the interface irq registers. This
change adds proper interface offsets for SC7280 target.
Rob Clark [Mon, 5 Apr 2021 17:45:31 +0000 (10:45 -0700)]
drm/msm: Support evicting GEM objects to swap
Now that tracking is wired up for potentially evictable GEM objects,
wire up shrinker and the remaining GEM bits for unpinning backing pages
of inactive objects.
Disabled by default for now, with an 'enable_eviction' module param to
enable so that we can get some more testing on the range of generations
(and iommu pairings) supported.
Rob Clark [Mon, 5 Apr 2021 17:45:30 +0000 (10:45 -0700)]
drm/msm: Small msm_gem_purge() fix
Shoot down any mmap's *first* before put_pages(). Also add a WARN_ON
that the object is locked (to make it clear that this doesn't race with
msm_gem_fault()) and remove a redundant WARN_ON (since is_purgable()
already covers that case).
Rob Clark [Mon, 5 Apr 2021 17:45:29 +0000 (10:45 -0700)]
drm/msm: Track potentially evictable objects
Objects that are potential for swapping out are (1) willneed (ie. if
they are purgable/MADV_WONTNEED we can just free the pages without them
having to land in swap), (2) not on an active list, (3) not dma-buf
imported or exported, and (4) not vmap'd. This repurposes the purged
list for objects that do not have backing pages (either because they
have not been pinned for the first time yet, or in a later patch because
they have been unpinned/evicted.
Rob Clark [Mon, 5 Apr 2021 17:45:28 +0000 (10:45 -0700)]
drm/msm: Add $debugfs/gem stats on resident objects
Currently nearly everything, other than newly allocated objects which
are not yet backed by pages, is pinned and resident in RAM. But it will
be nice to have some stats on what is unpinned once that is supported.
Rob Clark [Mon, 5 Apr 2021 17:45:27 +0000 (10:45 -0700)]
drm/msm: Split iova purge and close
Currently these always go together, either when we purge MADV_WONTNEED
objects or when the object is freed. But for unpin, we want to be able
to purge (unmap from iommu) the vma, while keeping the iova range
allocated (so we can remap back to the same GPU virtual address when the
object is re-pinned.
Rob Clark [Mon, 5 Apr 2021 17:45:26 +0000 (10:45 -0700)]
drm/msm: Clear msm_obj->sgt in put_pages()
Currently this doesn't matter since we keep the pages pinned until the
object is destroyed. But when we start unpinning pages to allow objects
to be evicted to swap, it will.
drm/msm/dpu: always use mdp device to scale bandwidth
Currently DPU driver scales bandwidth and core clock for sc7180 only,
while the rest of chips get static bandwidth votes. Make all chipsets
scale bandwidth and clock per composition requirements like sc7180 does.
Drop old voting path completely.
Dmitry Baryshkov [Thu, 18 Mar 2021 10:54:35 +0000 (13:54 +0300)]
drm/msm/dpu: enable DPU_SSPP_QOS_8LVL for SM8250
SM8250 platform has a 8-Levels VIG QoS setting. This setting was missed
due to bad interaction with b8dab65b5ac3 ("drm/msm/dpu: Move
DPU_SSPP_QOS_8LVL bit to SDM845 and SC7180 masks"), which was applied in
parallel.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:35 +0000 (13:57 +0300)]
drm/msm/dsi: stop passing src_pll_id to the phy_enable call
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:34 +0000 (13:57 +0300)]
drm/msm/dsi: inline msm_dsi_phy_set_src_pll
The src_truthtable config is not used for some of phys, which use other
means of configuring the master/slave usecases. Inline this function
with the goal of removing src_pll_id argument in the next commit.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:33 +0000 (13:57 +0300)]
drm/msm/dsi: remove temp data from global pll structure
The 7nm, 10nm and 14nm drivers would store interim data used during
VCO/PLL rate setting in the global dsi_pll_Nnm structure. Move this data
structures to the onstack storage. While we are at it, drop
unused/static 'config' data, unused config fields, etc.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:31 +0000 (13:57 +0300)]
drm/msm/dsi: move ioremaps to dsi_phy_driver_probe
All PHY drivers would map dsi_pll area. Some PHY drivers would also
map dsi_phy area again (a leftover from old PHY/PLL separation). Move
all ioremaps to the common dsi_phy driver code and drop individual
ioremapped areas from PHY drivers.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:28 +0000 (13:57 +0300)]
drm/msm/dsi: make save_state/restore_state callbacks accept msm_dsi_phy
Make save_state/restore callbacks accept struct msm_dsi_phy rather than
struct msm_dsi_pll. This moves them to struct msm_dsi_phy_ops, allowing
us to drop struct msm_dsi_pll_ops.
10nm and 7nm already do not use these helpers, as they handle setting
slave DSI clocks after enabling VCO. Modify the rest of PHY drivers to
remove unnecessary indirection and drop enable_seq/disable_seq PLL
callbacks.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:21 +0000 (13:57 +0300)]
drm/msm/dsi: push provided clocks handling into a generic code
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:20 +0000 (13:57 +0300)]
drm/msm/dsi: remove msm_dsi_pll_set_usecase
msm_dsi_pll_set_usecase() function is not used outside of individual DSI
PHY drivers, so drop it in favour of calling the the respective
set_usecase functions directly.
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:18 +0000 (13:57 +0300)]
drm/msm/dsi: drop global msm_dsi_phy_type enumaration
With the current upstream driver the msm_dsi_phy_type enum does not make
much sense: all DSI PHYs are probed using the dt bindings, the phy type
is not passed between drivers. Use quirks in phy individual PHY drivers
to differentiate minor harware differences and drop the enum.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor Link: https://lore.kernel.org/r/20210331105735.3690009-8-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:15 +0000 (13:57 +0300)]
drm/msm/dsi: fuse dsi_pll_* code into dsi_phy_* code
Each phy version is tightly coupled with the corresponding PLL code,
there is no need to keep them separate. Fuse source files together in
order to simplify DSI code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor Link: https://lore.kernel.org/r/20210331105735.3690009-5-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 31 Mar 2021 10:57:14 +0000 (13:57 +0300)]
drm/msm/dsi: replace PHY's init callback with configurable data
DSI PHY init callback would either map dsi_phy_regulator or dsi_phy_lane
depending on the PHY type. Replace those callbacks with configuration
options governing mapping those regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor Link: https://lore.kernel.org/r/20210331105735.3690009-4-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the error checking logic in the dp_debug module could
pass zero to PTR_ERR and it causes the below kbot warnings:
drivers/gpu/drm/msm/dp/dp_debug.c:378 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:387 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:396 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:405 dp_debug_init()
warn: passing zero to 'PTR_ERR'
Debugfs functions are not supposed to be checked in the normal
case so delete this code. Also it silences the above Smatch
warnings that we're checking for NULL when these functions only
return error pointers.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1614971839-2686-3-git-send-email-abhinavk@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Abhinav Kumar [Fri, 5 Mar 2021 19:17:18 +0000 (11:17 -0800)]
drm/msm/dp: Fix incorrect NULL check kbot warnings in DP driver
Fix an incorrect NULL check reported by kbot in the MSM DP driver
smatch warnings:
drivers/gpu/drm/msm/dp/dp_hpd.c:37 dp_hpd_connect()
error: we previously assumed 'hpd_priv->dp_cb' could be null
(see line 37)
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1614971839-2686-2-git-send-email-abhinavk@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1614971839-2686-1-git-send-email-abhinavk@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Kalyan Thota [Thu, 18 Feb 2021 12:35:46 +0000 (04:35 -0800)]
drm/msm/disp/dpu1: turn off vblank irqs aggressively in dpu driver
Set the flag vblank_disable_immediate = true to turn off vblank irqs
immediately as soon as drm_vblank_put is requested so that there are
no irqs triggered during idle state. This will reduce cpu wakeups
and help in power saving.
To enable vblank_disable_immediate flag the underlying KMS driver
needs to support high precision vblank timestamping and also a
reliable way of providing vblank counter which is incrementing
at the leading edge of vblank.
This patch also brings in changes to support vblank_disable_immediate
requirement in dpu driver.
Changes in v1:
- Specify reason to add vblank timestamp support. (Rob).
- Add changes to provide vblank counter from dpu driver.
Changes in v2:
- Fix warn stack reported by Rob Clark with v2 patch.
Changes in v3:
- Move back to HW frame counter (Rob).
Changes in v4:
- Frame count mismatch was causing a DRM WARN stack spew.
DPU HW will increment the frame count at the end of
the sync, where as vblank will be triggered at the
fetch_start counter which is calculated as v_total - vfp.
This is to start fetching early for panels with low
vbp w.r.t hw latency lines.
Add logic to detect the line count if it falls between
vactive and v_total then return incremented frame count value.
Rob Clark [Thu, 25 Mar 2021 01:23:53 +0000 (18:23 -0700)]
drm/msm: Add param for userspace to query suspend count
Performance counts, and ALWAYS_ON counters used for capturing GPU
timestamps, lose their state across suspend/resume cycles. Userspace
tooling for performance monitoring needs to be aware of this. For
example, after a suspend userspace needs to recalibrate it's offset
between CPU and GPU time.
We were not programing the correct bit while clearing the perfcounter oob.
So, clear it correctly using the new 'clear' bit. This fixes the below
error:
[drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set PERFCOUNTER: 0x80000000
Jonathan Marek [Mon, 29 Mar 2021 12:00:50 +0000 (15:00 +0300)]
drm/msm: add compatibles for sm8150/sm8250 display
The driver already has support for sm8150/sm8250, but the compatibles were
never added.
Also inverse the non-mdp4 condition in add_display_components() to avoid
having to check every new compatible in the condition.
Signed-off-by: Jonathan Marek <jonathan@marek.ca> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210329120051.3401567-4-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org>
Bjorn Andersson [Wed, 17 Mar 2021 02:56:34 +0000 (19:56 -0700)]
drm/msm: Remove need for reiterating the compatibles
After spending a non-negligible time trying to figure out why
dpu_kms_init() would dereference a NULL dpu_kms->pdev, it turns out that
in addition to adding the new compatible to the msm_drv of_match_table
one also need to teach add_display_components() to register the child
nodes - which includes the DPU platform_device.
Replace the open coded test for compatibles with a check against the
match data of the mdss device to save others this trouble in the future.
Rob Clark [Thu, 1 Apr 2021 01:27:21 +0000 (18:27 -0700)]
drm/msm: Improved debugfs gem stats
The last patch lost the breakdown of active vs inactive GEM objects in
$debugfs/gem. But we can add some better stats to summarize not just
active vs inactive, but also purgable/purged to make up for that.
Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210401012722.527712-5-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Rob Clark [Thu, 1 Apr 2021 01:27:20 +0000 (18:27 -0700)]
drm/msm: Fix debugfs deadlock
In normal cases the gem obj lock is acquired first before mm_lock. The
exception is iterating the various object lists. In the shrinker path,
deadlock is avoided by using msm_gem_trylock() and skipping over objects
that cannot be locked. But for debugfs the straightforward thing is to
split things out into a separate list of all objects protected by it's
own lock.
Fixes: d984457b31c4 ("drm/msm: Add priv->mm_lock to protect active/inactive lists") Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210401012722.527712-4-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Rob Clark [Thu, 1 Apr 2021 01:27:19 +0000 (18:27 -0700)]
drm/msm: Avoid mutex in shrinker_count()
When the system is under heavy memory pressure, we can end up with lots
of concurrent calls into the shrinker. Keeping a running tab on what we
can shrink avoids grabbing a lock in shrinker->count(), and avoids
shrinker->scan() getting called when not profitable.
Also, we can keep purged objects in their own list to avoid re-traversing
them to help cut down time in the critical section further.
Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210401012722.527712-3-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Rob Clark [Thu, 1 Apr 2021 01:27:18 +0000 (18:27 -0700)]
drm/msm: Remove unused freed llist node
Unused since commit c951a9b284b9 ("drm/msm: Remove msm_gem_free_work")
Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210401012722.527712-2-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 31 Mar 2021 14:02:23 +0000 (17:02 +0300)]
drm/msm: a6xx: fix version check for the A650 SQE microcode
I suppose the microcode version check for a650 is incorrect. It checks
for the version 1.95, while the firmware released have major version of 0:
0.91 (vulnerable), 0.99 (fixing the issue).
Lower version requirements to accept firmware 0.99.
Fixes: 8490f02a3ca4 ("drm/msm: a6xx: Make sure the SQE microcode is safe") Cc: Akhil P Oommen <akhilpo@codeaurora.org> Cc: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210331140223.3771449-1-dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Rob Clark [Thu, 25 Mar 2021 01:23:52 +0000 (18:23 -0700)]
drm/msm: Fix a5xx/a6xx timestamps
They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON. This
isn't the thing that userspace is looking for.
Signed-off-by: Rob Clark <robdclark@chromium.org> Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org>
John Stultz [Tue, 30 Mar 2021 01:34:08 +0000 (01:34 +0000)]
drm/msm: Fix removal of valid error case when checking speed_bin
Commit 7bf168c8fe8c ("drm/msm: Fix speed-bin support not to
access outside valid memory"), reworked the nvmem reading of
"speed_bin", but in doing so dropped handling of the -ENOENT
case which was previously documented as "fine".
That change resulted in the db845c board display to fail to
start, with the following error:
adreno 5000000.gpu: [drm:a6xx_gpu_init] *ERROR* failed to read speed-bin (-2). Some OPPs may not be supported by hardware
Thus, this patch simply re-adds the ENOENT handling so the lack
of the speed_bin entry isn't fatal for display, and gets things
working on db845c.
Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Eric Anholt <eric@anholt.net> Cc: Douglas Anderson <dianders@chromium.org> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: YongQin Liu <yongqin.liu@linaro.org> Reported-by: YongQin Liu <yongqin.liu@linaro.org> Fixes: 7bf168c8fe8c ("drm/msm: Fix speed-bin support not to access outside valid memory") Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Message-Id: <20210330013408.2532048-1-john.stultz@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Stephen Boyd [Thu, 25 Mar 2021 21:28:22 +0000 (14:28 -0700)]
drm/msm: Set drvdata to NULL when msm_drm_init() fails
We should set the platform device's driver data to NULL here so that
code doesn't assume the struct drm_device pointer is valid when it could
have been destroyed. The lifetime of this pointer is managed by a kref
but when msm_drm_init() fails we call drm_dev_put() on the pointer which
will free the pointer's memory. This driver uses the component model, so
there's sort of two "probes" in this file, one for the platform device
i.e. msm_pdev_probe() and one for the component i.e. msm_drm_bind(). The
msm_drm_bind() code is using the platform device's driver data to store
struct drm_device so the two functions are intertwined.
This relationship becomes a problem for msm_pdev_shutdown() when it
tests the NULL-ness of the pointer to see if it should call
drm_atomic_helper_shutdown(). The NULL test is a proxy check for if the
pointer has been freed by kref_put(). If the drm_device has been
destroyed, then we shouldn't call the shutdown helper, and we know that
is the case if msm_drm_init() failed, therefore set the driver data to
NULL so that this pointer liveness is tracked properly.
Fixes: 9d5cbf5fe46e ("drm/msm: add shutdown support for display platform_driver") Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Krishna Manikandan <mkrishn@codeaurora.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Message-Id: <20210325212822.3663144-1-swboyd@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Kalyan Thota [Mon, 22 Mar 2021 09:17:12 +0000 (02:17 -0700)]
drm/msm/disp/dpu1: icc path needs to be set before dpu runtime resume
DPU runtime resume will request for a min vote on the AXI bus as
it is a necessary step before turning ON the AXI clock.
The change does below
1) Move the icc path set before requesting runtime get_sync.
2) remove the dependency of hw catalog for min ib vote
as it is initialized at a later point.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org> Tested-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Fabio Estevam [Sat, 20 Mar 2021 11:56:03 +0000 (08:56 -0300)]
drm/msm: Fix suspend/resume on i.MX5
When putting iMX5 into suspend, the following flow is
observed:
[ 70.023427] [<c07755f0>] (msm_atomic_commit_tail) from [<c06e7218>]
(commit_tail+0x9c/0x18c)
[ 70.031890] [<c06e7218>] (commit_tail) from [<c0e2920c>]
(drm_atomic_helper_commit+0x1a0/0x1d4)
[ 70.040627] [<c0e2920c>] (drm_atomic_helper_commit) from
[<c06e74d4>] (drm_atomic_helper_disable_all+0x1c4/0x1d4)
[ 70.050913] [<c06e74d4>] (drm_atomic_helper_disable_all) from
[<c0e2943c>] (drm_atomic_helper_suspend+0xb8/0x170)
[ 70.061198] [<c0e2943c>] (drm_atomic_helper_suspend) from
[<c06e84bc>] (drm_mode_config_helper_suspend+0x24/0x58)
In the i.MX5 case, priv->kms is not populated (as i.MX5 does not use any
of the Qualcomm display controllers), causing a NULL pointer
dereference in msm_atomic_commit_tail():
[ 24.268964] 8<--- cut here ---
[ 24.274602] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
[ 24.283434] pgd = (ptrval)
[ 24.286387] [00000000] *pgd=ca212831
[ 24.290788] Internal error: Oops: 17 [#1] SMP ARM
[ 24.295609] Modules linked in:
[ 24.298777] CPU: 0 PID: 197 Comm: init Not tainted 5.11.0-rc2-next-20210111 #333
[ 24.306276] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 24.312442] PC is at msm_atomic_commit_tail+0x54/0xb9c
[ 24.317743] LR is at commit_tail+0xa4/0x1b0
Fix the problem by calling drm_mode_config_helper_suspend/resume()
only when priv->kms is available.
Fixes: ca8199f13498 ("drm/msm/dpu: ensure device suspend happens during PM sleep") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Sat, 20 Mar 2021 11:56:02 +0000 (08:56 -0300)]
drm/msm: fix shutdown hook in case GPU components failed to bind
If GPU components have failed to bind, shutdown callback would fail with
the following backtrace. Add safeguard check to stop that oops from
happening and allow the board to reboot.
Rob Clark [Wed, 17 Mar 2021 16:40:38 +0000 (09:40 -0700)]
drm/msm: Ratelimit invalid-fence message
We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause. Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Konrad Dybcio [Sun, 28 Feb 2021 12:36:51 +0000 (13:36 +0100)]
drm/msm/adreno: a5xx_power: Don't apply A540 lm_setup to other GPUs
While passing the A530-specific lm_setup func to A530 and A540
to !A530 was fine back when only these two were supported, it
certainly is not a good idea to send A540 specifics to smaller
GPUs like A508 and friends.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Stephen Boyd [Fri, 26 Feb 2021 21:08:21 +0000 (13:08 -0800)]
drm/msm/dp: Restore aux retry tuning logic
In commit 9fc418430c65 ("drm/msm/dp: unplug interrupt missed after
irq_hpd handler") we dropped a reset of the aux phy during aux transfers
because resetting the phy during active communication caused us to miss
an hpd irq in some cases. Unfortunately, we also dropped the part of the
code that changes the aux phy tuning when an aux transfer fails due to a
timeout. That part of the code was calling into the phy driver to
reconfigure the aux TX swing controls, working around poor channel
quality. Let's restore this phy setting code so that aux channel
communication is more reliable.
Cc: Kuogee Hsieh <khsieh@codeaurora.org> Fixes: 9fc418430c65 ("drm/msm/dp: unplug interrupt missed after irq_hpd handler") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 24 Feb 2021 23:05:28 +0000 (02:05 +0300)]
drm/msm/dsi_pll_7nm: Fix variable usage for pll_lockdet_rate
The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Based on 362cadf34b9f ("drm/msm/dsi_pll_10nm: Fix variable usage for
pll_lockdet_rate")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 24 Feb 2021 23:01:43 +0000 (02:01 +0300)]
drm/msm/dsi_pll_7nm: Solve TODO for multiplier frac_bits assignment
The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 7nm:
remove the TODO by simply using that variable. This is a copy of 196145eb1af1 ("drm/msm/dsi_pll_10nm: Solve TODO for multiplier frac_bits
assignment").
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov [Wed, 24 Feb 2021 22:47:51 +0000 (01:47 +0300)]
drm/msm/dsi: fix check-before-set in the 7nm dsi_pll code
Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.
Cc: Jonathan Marek <jonathan@marek.ca> Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org>
Alexey Dobriyan [Sun, 14 Mar 2021 20:51:14 +0000 (23:51 +0300)]
prctl: fix PR_SET_MM_AUXV kernel stack leak
Doing a
prctl(PR_SET_MM, PR_SET_MM_AUXV, addr, 1);
will copy 1 byte from userspace to (quite big) on-stack array
and then stash everything to mm->saved_auxv.
AT_NULL terminator will be inserted at the very end.
/proc/*/auxv handler will find that AT_NULL terminator
and copy original stack contents to userspace.
Linus Torvalds [Sun, 14 Mar 2021 20:33:33 +0000 (13:33 -0700)]
Merge tag 'irq-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of irqchip updates:
- Make the GENERIC_IRQ_MULTI_HANDLER configuration correct
- Add a missing DT compatible string for the Ingenic driver
- Remove the pointless debugfs_file pointer from struct irqdomain"
* tag 'irq-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Add support for the JZ4760
dt-bindings/irq: Add compatible string for the JZ4760B
irqchip: Do not blindly select CONFIG_GENERIC_IRQ_MULTI_HANDLER
ARM: ep93xx: Select GENERIC_IRQ_MULTI_HANDLER directly
irqdomain: Remove debugfs_file from struct irq_domain
Linus Torvalds [Sun, 14 Mar 2021 20:29:38 +0000 (13:29 -0700)]
Merge tag 'timers-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix in for hrtimers to prevent an interrupt storm caused by
the lack of reevaluation of the timers which expire in softirq context
under certain circumstances, e.g. when the clock was set"
* tag 'timers-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Update softirq_expires_next correctly after __hrtimer_get_next_event()
Linus Torvalds [Sun, 14 Mar 2021 20:15:55 +0000 (13:15 -0700)]
Merge tag 'objtool-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fix from Thomas Gleixner:
"A single objtool fix to handle the PUSHF/POPF validation correctly for
the paravirt changes which modified arch_local_irq_restore not to use
popf"
* tag 'objtool-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool,x86: Fix uaccess PUSHF/POPF validation
Linus Torvalds [Sun, 14 Mar 2021 20:03:21 +0000 (13:03 -0700)]
Merge tag 'locking-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A couple of locking fixes:
- A fix for the static_call mechanism so it handles unaligned
addresses correctly.
- Make u64_stats_init() a macro so every instance gets a seperate
lockdep key.
- Make seqcount_latch_init() a macro as well to preserve the static
variable which is used for the lockdep key"
* tag 'locking-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
seqlock,lockdep: Fix seqcount_latch_init()
u64_stats,lockdep: Fix u64_stats_init() vs lockdep
static_call: Fix the module key fixup
Linus Torvalds [Sun, 14 Mar 2021 19:57:17 +0000 (12:57 -0700)]
Merge tag 'perf_urgent_for_v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Make sure PMU internal buffers are flushed for per-CPU events too and
properly handle PID/TID for large PEBS.
- Handle the case properly when there's no PMU and therefore return an
empty list of perf MSRs for VMX to switch instead of reading random
garbage from the stack.
* tag 'perf_urgent_for_v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/perf: Use RET0 as default for guest_get_msrs to handle "no PMU" case
perf/x86/intel: Set PERF_ATTACH_SCHED_CB for large PEBS and LBR
perf/core: Flush PMU internal buffers for per-CPU events
Linus Torvalds [Sun, 14 Mar 2021 19:54:56 +0000 (12:54 -0700)]
Merge tag 'efi-urgent-for-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Ard Biesheuvel via Borislav Petkov:
"Fix an oversight in the handling of EFI_RT_PROPERTIES_TABLE, which was
added v5.10, but failed to take the SetVirtualAddressMap() RT service
into account"
* tag 'efi-urgent-for-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: stub: omit SetVirtualAddressMap() if marked unsupported in RT_PROP table
Linus Torvalds [Sun, 14 Mar 2021 19:48:10 +0000 (12:48 -0700)]
Merge tag 'x86_urgent_for_v5.12_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- A couple of SEV-ES fixes and robustifications: verify usermode stack
pointer in NMI is not coming from the syscall gap, correctly track
IRQ states in the #VC handler and access user insn bytes atomically
in same handler as latter cannot sleep.
- Balance 32-bit fast syscall exit path to do the proper work on exit
and thus not confuse audit and ptrace frameworks.
- Two fixes for the ORC unwinder going "off the rails" into KASAN
redzones and when ORC data is missing.
* tag 'x86_urgent_for_v5.12_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev-es: Use __copy_from_user_inatomic()
x86/sev-es: Correctly track IRQ states in runtime #VC handler
x86/sev-es: Check regs->sp is trusted before adjusting #VC IST stack
x86/sev-es: Introduce ip_within_syscall_gap() helper
x86/entry: Fix entry/exit mismatch on failed fast 32-bit syscalls
x86/unwind/orc: Silence warnings caused by missing ORC data
x86/unwind/orc: Disable KASAN checking in the ORC unwinder, part 2
Linus Torvalds [Sun, 14 Mar 2021 19:37:43 +0000 (12:37 -0700)]
Merge tag 'powerpc-5.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.12:
- Fix wrong instruction encoding for lis in ppc_function_entry(),
which could potentially lead to missed kprobes.
- Fix SET_FULL_REGS on 32-bit and 64e, which prevented ptrace of
non-volatile GPRs immediately after exec.
- Clean up a missed SRR specifier in the recent interrupt rework.
- Don't treat unrecoverable_exception() as an interrupt handler, it's
called from other handlers so shouldn't do the interrupt entry/exit
accounting itself.
- Fix build errors caused by missing declarations for
[en/dis]able_kernel_vsx().
Thanks to Christophe Leroy, Daniel Axtens, Geert Uytterhoeven, Jiri
Olsa, Naveen N. Rao, and Nicholas Piggin"
* tag 'powerpc-5.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/traps: unrecoverable_exception() is not an interrupt handler
powerpc: Fix missing declaration of [en/dis]able_kernel_vsx()
powerpc/64s/exception: Clean up a missed SRR specifier
powerpc: Fix inverted SET_FULL_REGS bitop
powerpc/64s: Use symbolic macros for function entry encoding
powerpc/64s: Fix instruction encoding for lis in ppc_function_entry()
Linus Torvalds [Sun, 14 Mar 2021 19:35:02 +0000 (12:35 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"More fixes for ARM and x86"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: LAPIC: Advancing the timer expiration on guest initiated write
KVM: x86/mmu: Skip !MMU-present SPTEs when removing SP in exclusive mode
KVM: kvmclock: Fix vCPUs > 64 can't be online/hotpluged
kvm: x86: annotate RCU pointers
KVM: arm64: Fix exclusive limit for IPA size
KVM: arm64: Reject VM creation when the default IPA size is unsupported
KVM: arm64: Ensure I-cache isolation between vcpus of a same VM
KVM: arm64: Don't use cbz/adr with external symbols
KVM: arm64: Fix range alignment when walking page tables
KVM: arm64: Workaround firmware wrongly advertising GICv2-on-v3 compatibility
KVM: arm64: Rename __vgic_v3_get_ich_vtr_el2() to __vgic_v3_get_gic_config()
KVM: arm64: Don't access PMSELR_EL0/PMUSERENR_EL0 when no PMU is available
KVM: arm64: Turn kvm_arm_support_pmu_v3() into a static key
KVM: arm64: Fix nVHE hyp panic host context restore
KVM: arm64: Avoid corrupting vCPU context register in guest exit
KVM: arm64: nvhe: Save the SPE context early
kvm: x86: use NULL instead of using plain integer as pointer
KVM: SVM: Connect 'npt' module param to KVM's internal 'npt_enabled'
KVM: x86: Ensure deadline timer has truly expired before posting its IRQ
Linus Torvalds [Sun, 14 Mar 2021 19:23:34 +0000 (12:23 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"28 patches.
Subsystems affected by this series: mm (memblock, pagealloc, hugetlb,
highmem, kfence, oom-kill, madvise, kasan, userfaultfd, memcg, and
zram), core-kernel, kconfig, fork, binfmt, MAINTAINERS, kbuild, and
ia64"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (28 commits)
zram: fix broken page writeback
zram: fix return value on writeback_store
mm/memcg: set memcg when splitting page
mm/memcg: rename mem_cgroup_split_huge_fixup to split_page_memcg and add nr_pages argument
ia64: fix ptrace(PTRACE_SYSCALL_INFO_EXIT) sign
ia64: fix ia64_syscall_get_set_arguments() for break-based syscalls
mm/userfaultfd: fix memory corruption due to writeprotect
kasan: fix KASAN_STACK dependency for HW_TAGS
kasan, mm: fix crash with HW_TAGS and DEBUG_PAGEALLOC
mm/madvise: replace ptrace attach requirement for process_madvise
include/linux/sched/mm.h: use rcu_dereference in in_vfork()
kfence: fix reports if constant function prefixes exist
kfence, slab: fix cache_alloc_debugcheck_after() for bulk allocations
kfence: fix printk format for ptrdiff_t
linux/compiler-clang.h: define HAVE_BUILTIN_BSWAP*
MAINTAINERS: exclude uapi directories in API/ABI section
binfmt_misc: fix possible deadlock in bm_register_write
mm/highmem.c: fix zero_user_segments() with start > end
hugetlb: do early cow when page pinned on src mm
mm: use is_cow_mapping() across tree where proper
...
Thomas Gleixner [Sun, 14 Mar 2021 15:34:35 +0000 (16:34 +0100)]
Merge tag 'irqchip-fixes-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- More compatible strings for the Ingenic irqchip (introducing the
JZ4760B SoC)
- Select GENERIC_IRQ_MULTI_HANDLER on the ARM ep93xx platform
- Drop all GENERIC_IRQ_MULTI_HANDLER selections from the irqchip
Kconfig, now relying on the architecture to get it right
- Drop the debugfs_file field from struct irq_domain, now that
debugfs can track things on its own
Linus Torvalds [Sat, 13 Mar 2021 20:38:44 +0000 (12:38 -0800)]
Merge tag 'char-misc-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small misc/char driver fixes to resolve some reported
problems:
- habanalabs driver fixes
- Acrn build fixes (reported many times)
- pvpanic module table export fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc/pvpanic: Export module FDT device table
misc: fastrpc: restrict user apps from sending kernel RPC messages
virt: acrn: Correct type casting of argument of copy_from_user()
virt: acrn: Use EPOLLIN instead of POLLIN
virt: acrn: Use vfs_poll() instead of f_op->poll()
virt: acrn: Make remove_cpu sysfs invisible with !CONFIG_HOTPLUG_CPU
cpu/hotplug: Fix build error of using {add,remove}_cpu() with !CONFIG_SMP
habanalabs: fix debugfs address translation
habanalabs: Disable file operations after device is removed
habanalabs: Call put_pid() when releasing control device
drivers: habanalabs: remove unused dentry pointer for debugfs files
habanalabs: mark hl_eq_inc_ptr() as static
Linus Torvalds [Sat, 13 Mar 2021 20:36:53 +0000 (12:36 -0800)]
Merge tag 'staging-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for reported problems. They
include:
- wfx header file cleanup patch reverted as it could cause problems
- comedi driver endian fixes
- buffer overflow problems for staging wifi drivers
- build dependency issue for rtl8192e driver
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
Revert "staging: wfx: remove unused included header files"
staging: rtl8188eu: prevent ->ssid overflow in rtw_wx_set_scan()
staging: rtl8188eu: fix potential memory corruption in rtw_check_beacon_data()
staging: rtl8192u: fix ->ssid overflow in r8192_wx_set_scan()
staging: comedi: pcl726: Use 16-bit 0 for interrupt data
staging: comedi: ni_65xx: Use 16-bit 0 for interrupt data
staging: comedi: ni_6527: Use 16-bit 0 for interrupt data
staging: comedi: comedi_parport: Use 16-bit 0 for interrupt data
staging: comedi: amplc_pc236_common: Use 16-bit 0 for interrupt data
staging: comedi: pcl818: Fix endian problem for AI command data
staging: comedi: pcl711: Fix endian problem for AI command data
staging: comedi: me4000: Fix endian problem for AI command data
staging: comedi: dmm32at: Fix endian problem for AI command data
staging: comedi: das800: Fix endian problem for AI command data
staging: comedi: das6402: Fix endian problem for AI command data
staging: comedi: adv_pci1710: Fix endian problem for AI command data
staging: comedi: addi_apci_1500: Fix endian problem for command sample
staging: comedi: addi_apci_1032: Fix endian problem for COS sample
staging: ks7010: prevent buffer overflow in ks_wlan_set_scan()
staging: rtl8712: Fix possible buffer overflow in r8712_sitesurvey_cmd
...
Linus Torvalds [Sat, 13 Mar 2021 20:34:29 +0000 (12:34 -0800)]
Merge tag 'tty-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes to resolve some
reported problems:
- led tty trigger fixes based on review and were acked by the led
maintainer
- revert a max310x serial driver patch as it was causing problems
- revert a pty change as it was also causing problems
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "drivers:tty:pty: Fix a race causing data loss on close"
Revert "serial: max310x: rework RX interrupt handling"
leds: trigger/tty: Use led_set_brightness_sync() from workqueue
leds: trigger: Fix error path to not unlock the unlocked mutex
Linus Torvalds [Sat, 13 Mar 2021 20:32:57 +0000 (12:32 -0800)]
Merge tag 'usb-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a small number of USB fixes for 5.12-rc3 to resolve a bunch
of reported issues:
- usbip fixups for issues found by syzbot
- xhci driver fixes and quirk additions
- gadget driver fixes
- dwc3 QCOM driver fix
- usb-serial new ids and fixes
- usblp fix for a long-time issue
- cdc-acm quirk addition
- other tiny fixes for reported problems
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
xhci: Fix repeated xhci wake after suspend due to uncleared internal wake state
usb: xhci: Fix ASMedia ASM1042A and ASM3242 DMA addressing
xhci: Improve detection of device initiated wake signal.
usb: xhci: do not perform Soft Retry for some xHCI hosts
usbip: fix vudc usbip_sockfd_store races leading to gpf
usbip: fix vhci_hcd attach_store() races leading to gpf
usbip: fix stub_dev usbip_sockfd_store() races leading to gpf
usbip: fix vudc to check for stream socket
usbip: fix vhci_hcd to check for stream socket
usbip: fix stub_dev to check for stream socket
usb: dwc3: qcom: Add missing DWC3 OF node refcount decrement
USB: usblp: fix a hang in poll() if disconnected
USB: gadget: udc: s3c2410_udc: fix return value check in s3c2410_udc_probe()
usb: renesas_usbhs: Clear PIPECFG for re-enabling pipe with other EPNUM
usb: dwc3: qcom: Honor wakeup enabled/disabled state
usb: gadget: f_uac1: stop playback on function disable
usb: gadget: f_uac2: always increase endpoint max_packet_size by one audio slot
USB: gadget: u_ether: Fix a configfs return code
usb: dwc3: qcom: add ACPI device id for sc8180x
Goodix Fingerprint device is not a modem
...
Linus Torvalds [Sat, 13 Mar 2021 20:26:22 +0000 (12:26 -0800)]
Merge tag 'erofs-for-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fix from Gao Xiang:
"Fix an urgent regression introduced by commit baa2c7c97153 ("block:
set .bi_max_vecs as actual allocated vector number"), which could
cause unexpected hung since linux 5.12-rc1.
Resolve it by avoiding using bio->bi_max_vecs completely"
* tag 'erofs-for-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix bio->bi_max_vecs behavior change
Linus Torvalds [Sat, 13 Mar 2021 20:18:59 +0000 (12:18 -0800)]
Merge tag 'kbuild-fixes-v5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- avoid 'make image_name' invoking syncconfig
- fix a couple of bugs in scripts/dummy-tools
- fix LLD_VENDOR and locale issues in scripts/ld-version.sh
- rebuild GCC plugins when the compiler is upgraded
- allow LTO to be enabled with KASAN_HW_TAGS
- allow LTO to be enabled without LLVM=1
* tag 'kbuild-fixes-v5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: fix ld-version.sh to not be affected by locale
kbuild: remove meaningless parameter to $(call if_changed_rule,dtc)
kbuild: remove LLVM=1 test from HAS_LTO_CLANG
kbuild: remove unneeded -O option to dtc
kbuild: dummy-tools: adjust to scripts/cc-version.sh
kbuild: Allow LTO to be selected with KASAN_HW_TAGS
kbuild: dummy-tools: support MPROFILE_KERNEL checks for ppc
kbuild: rebuild GCC plugins when the compiler is upgraded
kbuild: Fix ld-version.sh script if LLD was built with LLD_VENDOR
kbuild: dummy-tools: fix inverted tests for gcc
kbuild: add image_name to no-sync-config-targets
Minchan Kim [Sat, 13 Mar 2021 05:08:41 +0000 (21:08 -0800)]
zram: fix broken page writeback
commit 0d8359620d9b ("zram: support page writeback") introduced two
problems. It overwrites writeback_store's return value as kstrtol's
return value, which makes return value zero so user could see zero as
return value of write syscall even though it wrote data successfully.
It also breaks index value in the loop in that it doesn't increase the
index any longer. It means it can write only first starting block index
so user couldn't write all idle pages in the zram so lose memory saving
chance.
This patch fixes those issues.
Link: https://lkml.kernel.org/r/20210312173949.2197662-2-minchan@kernel.org Fixes: 0d8359620d9b("zram: support page writeback") Signed-off-by: Minchan Kim <minchan@kernel.org> Reported-by: Amos Bianchi <amosbianchi@google.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: John Dias <joaodias@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Sat, 13 Mar 2021 05:08:38 +0000 (21:08 -0800)]
zram: fix return value on writeback_store
writeback_store's return value is overwritten by submit_bio_wait's return
value. Thus, writeback_store will return zero since there was no IO
error. In the end, write syscall from userspace will see the zero as
return value, which could make the process stall to keep trying the write
until it will succeed.
Link: https://lkml.kernel.org/r/20210312173949.2197662-1-minchan@kernel.org Fixes: 3b82a051c101("drivers/block/zram/zram_drv.c: fix error return codes not being returned in writeback_store") Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: John Dias <joaodias@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhou Guanghui [Sat, 13 Mar 2021 05:08:33 +0000 (21:08 -0800)]
mm/memcg: set memcg when splitting page
As described in the split_page() comment, for the non-compound high order
page, the sub-pages must be freed individually. If the memcg of the first
page is valid, the tail pages cannot be uncharged when be freed.
For example, when alloc_pages_exact is used to allocate 1MB continuous
physical memory, 2MB is charged(kmemcg is enabled and __GFP_ACCOUNT is
set). When make_alloc_exact free the unused 1MB and free_pages_exact free
the applied 1MB, actually, only 4KB(one page) is uncharged.
Therefore, the memcg of the tail page needs to be set when splitting a
page.
Michel:
There are at least two explicit users of __GFP_ACCOUNT with
alloc_exact_pages added recently. See 7efe8ef274024 ("KVM: arm64:
Allocate stage-2 pgd pages with GFP_KERNEL_ACCOUNT") and c419621873713
("KVM: s390: Add memcg accounting to KVM allocations"), so this is not
just a theoretical issue.
Link: https://lkml.kernel.org/r/20210304074053.65527-3-zhouguanghui1@huawei.com Signed-off-by: Zhou Guanghui <zhouguanghui1@huawei.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Hugh Dickins <hughd@google.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Rui Xiang <rui.xiang@huawei.com> Cc: Tianhong Ding <dingtianhong@huawei.com> Cc: Weilong Chen <chenweilong@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhou Guanghui [Sat, 13 Mar 2021 05:08:30 +0000 (21:08 -0800)]
mm/memcg: rename mem_cgroup_split_huge_fixup to split_page_memcg and add nr_pages argument
Rename mem_cgroup_split_huge_fixup to split_page_memcg and explicitly pass
in page number argument.
In this way, the interface name is more common and can be used by
potential users. In addition, the complete info(memcg and flag) of the
memcg needs to be set to the tail pages.
Link: https://lkml.kernel.org/r/20210304074053.65527-2-zhouguanghui1@huawei.com Signed-off-by: Zhou Guanghui <zhouguanghui1@huawei.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Tianhong Ding <dingtianhong@huawei.com> Cc: Weilong Chen <chenweilong@huawei.com> Cc: Rui Xiang <rui.xiang@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log