net: dsa: xrs700x: fix missing initialisation of ds->phylink_mac_ops
The kernel build bot identified the following mistake in the recently
merged 860a9bed2651 ("net: dsa: xrs700x: provide own phylink MAC
operations") patch:
drivers/net/dsa/xrs700x/xrs700x.c:714:37: warning: 'xrs700x_phylink_mac_ops' defined but not used [-Wunused-const-variable=]
714 | static const struct phylink_mac_ops xrs700x_phylink_mac_ops = {
| ^~~~~~~~~~~~~~~~~~~~~~~
Fix the omitted assignment of ds->phylink_mac_ops.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Apr 2024 10:38:04 +0000 (11:38 +0100)]
Merge branch 'net-rps-lockless'
Jason Xing says:
====================
locklessly protect left members in struct rps_dev_flow
From: Jason Xing <kernelxing@tencent.com>
Since Eric did a more complicated locklessly change to last_qtail
member[1] in struct rps_dev_flow, the left members are easier to change
as the same.
One thing important I would like to share by qooting Eric:
"rflow is located in rxqueue->rps_flow_table, it is thus private to current
thread. Only one cpu can service an RX queue at a time."
So we only pay attention to the reader in the rps_may_expire_flow() and
writer in the set_rps_cpu(). They are in the two different contexts.
Jason Xing [Thu, 18 Apr 2024 07:36:03 +0000 (15:36 +0800)]
net: rps: locklessly access rflow->cpu
This is the last member in struct rps_dev_flow which should be
protected locklessly. So finish it.
Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Xing [Thu, 18 Apr 2024 07:36:02 +0000 (15:36 +0800)]
net: rps: protect filter locklessly
As we can see, rflow->filter can be written/read concurrently, so
lockless access is needed.
Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Xing [Thu, 18 Apr 2024 07:36:01 +0000 (15:36 +0800)]
net: rps: protect last_qtail with rps_input_queue_tail_save() helper
Removing one unnecessary reader protection and add another writer
protection to finish the locklessly proctection job.
Note: the removed READ_ONCE() is not needed because we only have to protect
the locklessly reader in the different context (rps_may_expire_flow()).
Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Apr 2024 10:34:08 +0000 (11:34 +0100)]
Merge branch 'net_sched-dump-no-rtnl'
Eric Dumazet says:
====================
net_sched: first series for RTNL-less qdisc dumps
Medium term goal is to implement "tc qdisc show" without needing
to acquire RTNL.
This first series makes the requested changes in 14 qdisc.
Notes :
- RTNL is still held in "tc qdisc show", more changes are needed.
- Qdisc returning many attributes might want/need to provide
a consistent set of attributes. If that is the case, their
dump() method could acquire the qdisc spinlock, to pair the
spinlock acquision in their change() method.
V2: Addressed Simon feedback (Thanks a lot Simon)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Apr 2024 07:32:36 +0000 (07:32 +0000)]
net_sched: cake: implement lockless cake_dump()
Instead of relying on RTNL, cake_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in cake_change().
v2: addressed Simon feedback in V1: https://lore.kernel.org/netdev/20240417083549.GA3846178@kernel.org/
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Toke Høiland-Jørgensen <toke@toke.dk> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
gve: Remove qpl_cfg struct since qpl_ids map with queues respectively
The qpl_cfg struct was used to make sure that no two different queues
are using QPL with the same qpl_id. We can remove that qpl_cfg struct
since now the qpl_ids map with the queues respectively as follows:
For tx queues: qpl_id = tx_qid
For rx queues: qpl_id = max_tx_queues + rx_qid
And when XDP is used, it will need the user to reduce the tx queues to
be at most half of the max_tx_queues. Then it will use the same number
of tx queues starting from the end of existing tx queues for XDP. So the
XDP queues will not exceed the max_tx_queues range and will not overlap
with the rx queues, where the qpl_ids will not have overlapping too.
Considering of that, we remove the qpl_cfg struct to get the qpl_id
directly based on the queue id. Unless we are erroneously allocating a
rx/tx queue that has already been allocated, we would never allocate
the qpl with the same qpl_id twice. In that case, it should fail much
earlier than the QPL assignment.
Jakub Kicinski [Fri, 19 Apr 2024 01:27:40 +0000 (18:27 -0700)]
Merge branch 'net: Add support for Power over Ethernet (PoE)'
Kory Maincent says:
====================
net: Add support for Power over Ethernet (PoE)
This patch series aims at adding support for PoE (Power over Ethernet),
based on the already existing support for PoDL (Power over Data Line)
implementation. In addition, it adds support for two specific PoE
controller, the Microchip PD692x0 and the TI TPS23881.
====================
net: pse-pd: Use regulator framework within PSE framework
Integrate the regulator framework to the PSE framework for enhanced
access to features such as voltage, power measurement, and limits, which
are akin to regulators. Additionally, PSE features like port priorities
could potentially enhance the regulator framework. Note that this
integration introduces some implementation complexity, including wrapper
callbacks, but the potential benefits make it worthwhile.
Regulator are using enable counter with specific behavior.
Two calls to regulator_disable will trigger kernel warnings.
If the counter exceeds one, regulator_disable call won't disable the
PSE PI. These behavior isn't suitable for PSE control.
Added a boolean 'enabled' state to prevent multiple calls to
regulator_enable/disable. These calls will only be called from PSE
framework as it won't have any regulator children, therefore no mutex are
needed to safeguards this boolean.
regulator_get needs the consumer device pointer. Use PSE as regulator
provider and consumer device until we have RJ45 ports represented in
the Kernel.
net: pse-pd: Add support for setup_pi_matrix callback
Implement setup_pi_matrix callback to configure the PSE PI matrix. This
functionality is invoked before registering the PSE and following the core
parsing of the pse_pis devicetree subnode.
dt-bindings: net: pse-pd: Add another way of describing several PSE PIs
PSE PI setup may encompass multiple PSE controllers or auxiliary circuits
that collectively manage power delivery to one Ethernet port.
Such configurations might support a range of PoE standards and require
the capability to dynamically configure power delivery based on the
operational mode (e.g., PoE2 versus PoE4) or specific requirements of
connected devices. In these instances, a dedicated PSE PI node becomes
essential for accurately documenting the system architecture. This node
would serve to detail the interactions between different PSE controllers,
the support for various PoE modes, and any additional logic required to
coordinate power delivery across the network infrastructure.
The old usage of "#pse-cells" is unsuficient as it carries only the PSE PI
index information.
The Power Sourcing Equipment Power Interface (PSE PI) plays a pivotal role
in the architecture of Power over Ethernet (PoE) systems. It is essentially
a blueprint that outlines how one or multiple power sources are connected
to the eight-pin modular jack, commonly known as the Ethernet RJ45 port.
This connection scheme is crucial for enabling the delivery of power
alongside data over Ethernet cables.
This patch adds support for getting the PSE controller node through PSE PI
device subnode.
This supports adds a way to get the PSE PI id from the pse_pi devicetree
subnode of a PSE controller node simply by reading the reg property.
Introduce an enumeration to define PSE types (C33 or PoDL),
utilizing a bitfield for potential future support of both types.
Include 'pse_get_types' helper for external access to PSE type info.
ethtool: Expand Ethernet Power Equipment with c33 (PoE) alongside PoDL
In the current PSE interface for Ethernet Power Equipment, support is
limited to PoDL. This patch extends the interface to accommodate the
objects specified in IEEE 802.3-2022 145.2 for Power sourcing
Equipment (PSE).
The following objects are now supported and considered mandatory:
- IEEE 802.3-2022 30.9.1.1.5 aPSEPowerDetectionStatus
- IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState
- IEEE 802.3-2022 30.9.1.2.1 aPSEAdminControl
To avoid confusion between "PoDL PSE" and "PoE PSE", which have similar
names but distinct values, we have followed the suggestion of Oleksij
Rempel and Andrew Lunn to maintain separate naming schemes for each,
using c33 (clause 33) prefix for "PoE PSE".
You can find more details in the discussion threads here:
https://lore.kernel.org/netdev/20230912110637.GI780075@pengutronix.de/
https://lore.kernel.org/netdev/2539b109-72ad-470a-9dae-9f53de4f64ec@lunn.ch/
Jakub Kicinski [Wed, 17 Apr 2024 23:11:40 +0000 (16:11 -0700)]
selftests: net: set the exit code correctly in Python tests
Test cases need to exit with non-zero status if they failed,
we currently don't do that:
# KTAP version 1
# 1..3
# # At /root/ksft-net-drv/drivers/net/./ping.py line 18:
# # Check failed 1 != 2
# not ok 1 ping.test_v4
# ok 2 ping.test_v6
# ok 3 ping.test_tcp
# # Totals: pass:2 fail:1 xfail:0 xpass:0 skip:0 error:0
ok 1 selftests: drivers/net: ping.py
^^^^
It's a bit tempting to make the exit part of ksft_run(),
but that only works well for very trivial setups. We can
revisit this later, if people forget to call ksft_exit().
Jakub Kicinski [Wed, 17 Apr 2024 23:11:39 +0000 (16:11 -0700)]
selftests: net: fix counting totals when some checks fail
Totals currently only pay attention to exceptions, if check fails
(say ksft_eq()) the test case will be counted as pass:
# At /ksft/drivers/net/./ping.py line 18:
# Check failed 1 != 2
not ok 1 ping.test_v4
ok 2 ping.test_v6
ok 3 ping.test_tcp
# Totals: pass:3 fail:0 xfail:0 xpass:0 skip:0 error:0
^^^^^^^^^^^^^
drivers/net/ethernet/intel/ice/ice_tc_lib.c 2cca35f5dd78 ("ice: Fix checking for unsupported keys on non-tunnel device") 784feaa65dfd ("ice: Add support for PFCP hardware offload in switchdev")
Merge tag 'net-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"A little calmer than usual, probably just the timing of sub-tree PRs.
Including fixes from netfilter.
Current release - regressions:
- inet: bring NLM_DONE out to a separate recv() again, fix user space
which assumes multiple recv()s will happen and gets blocked forever
- drv: mlx5:
- restore mistakenly dropped parts in register devlink flow
- use channel mdev reference instead of global mdev instance for
coalescing
- acquire RTNL lock before RQs/SQs activation/deactivation
Previous releases - regressions:
- net: change maximum number of UDP segments to 128, fix virtio
compatibility with Windows peers
- usb: ax88179_178a: avoid writing the mac address before first
reading
Previous releases - always broken:
- sched: fix mirred deadlock on device recursion
- netfilter:
- br_netfilter: skip conntrack input hook for promisc packets
- fixes removal of duplicate elements in the pipapo set backend
- various fixes for abort paths and error handling
- af_unix: don't peek OOB data without MSG_OOB
- drv: flower: fix fragment flags handling in multiple drivers
- drv: ravb: fix jumbo frames and packet stats accounting
Misc:
- kselftest_harness: fix Clang warning about zero-length format
- tun: limit printing rate when illegal packet received by tun dev"
* tag 'net-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
net: usb: ax88179_178a: avoid writing the mac address before first reading
net: ravb: Fix RX byte accounting for jumbo packets
net: ravb: Fix GbEth jumbo packet RX checksum handling
net: ravb: Allow RX loop to move past DMA mapping errors
net: ravb: Count packets instead of descriptors in R-Car RX path
net: ethernet: mtk_eth_soc: fix WED + wifi reset
net:usb:qmi_wwan: support Rolling modules
selftests: kselftest_harness: fix Clang warning about zero-length format
net/sched: Fix mirred deadlock on device recursion
netfilter: nf_tables: fix memleak in map from abort path
netfilter: nf_tables: restore set elements when delete set fails
netfilter: nf_tables: missing iterator type in lookup walk
s390/ism: Properly fix receive message buffer allocation
net: dsa: mt7530: fix port mirroring for MT7988 SoC switch
net: dsa: mt7530: fix mirroring frames received on local port
tun: limit printing rate when illegal packet received by tun dev
ice: Fix checking for unsupported keys on non-tunnel device
ice: tc: allow zero flags in parsing tc flower
ice: tc: check src_vsi in case of traffic from VF
...
net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Reported-by: Schuyler Patton <spatton@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: usb: ax88179_178a: avoid writing the mac address before first reading
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+ Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets") Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'random-6.9-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- The input subsystem contributes entropy in some places where a
spinlock is held, but the entropy accounting code only handled
callers being in an interrupt or non-atomic process context, but not
atomic process context. We fix this by removing an optimization and
just calling queue_work() unconditionally.
- Greg accidently sent up a patch not intended for his tree and that
had been nack'd, so that's now reverted.
* tag 'random-6.9-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
Revert "vmgenid: emit uevent when VMGENID updates"
random: handle creditable entropy from atomic process context
- x86/intel-uncore-freq: Bump minor version to avoid "unsupported" message
- amd/pmc: New BIOS version still needs Spurious IRQ1 quirk
* tag 'platform-drivers-x86-v6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/pmc: Extend Framework 13 quirk to more BIOSes
platform/x86/intel-uncore-freq: Increase minor number support
platform/x86: ISST: Add Granite Rapids-D to HPM CPU list
platform/x86/amd: pmf: Add quirk for ROG Zephyrus G14
platform/x86/amd: pmf: Add infrastructure for quirking supported funcs
platform/x86/amd: pmf: Decrease error message to debug
Revert "vmgenid: emit uevent when VMGENID updates"
This reverts commit ad6bcdad2b6724e113f191a12f859a9e8456b26d. I had
nak'd it, and Greg said on the thread that it links that he wasn't going
to take it either, especially since it's not his code or his tree, but
then, seemingly accidentally, it got pushed up some months later, in
what looks like a mistake, with no further discussion in the linked
thread. So revert it, since it's clearly not intended.
Fixes: ad6bcdad2b67 ("vmgenid: emit uevent when VMGENID updates") Cc: stable@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20230531095119.11202-2-bchalios@amazon.es Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The RSS hash report is a feature that's part of the virtio specification.
Currently, virtio backends like qemu, vdpa (mlx5), and potentially vhost
(still a work in progress as per [1]) support this feature. While the
capability to obtain the RSS hash has been enabled in the normal path,
it's currently missing in the XDP path. Therefore, we are introducing
XDP hints through kfuncs to allow XDP programs to access the RSS hash.
Paolo Abeni [Thu, 18 Apr 2024 11:12:36 +0000 (13:12 +0200)]
Merge tag 'nf-24-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 amends a missing spot where the set iterator type is unset.
This is fixing a issue in the previous pull request.
Patch #2 fixes the delete set command abort path by restoring state
of the elements. Reverse logic for the activate (abort) case
otherwise element state is not restored, this requires to move
the check for active/inactive elements to the set iterator
callback. From the deactivate path, toggle the next generation
bit and from the activate (abort) path, clear the next generation
bitmask.
Patch #3 skips elements already restored by delete set command from the
abort path in case there is a previous delete element command in
the batch. Check for the next generation bit just like it is done
via set iteration to restore maps.
netfilter pull request 24-04-18
* tag 'nf-24-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: fix memleak in map from abort path
netfilter: nf_tables: restore set elements when delete set fails
netfilter: nf_tables: missing iterator type in lookup walk
====================
Paolo Abeni [Thu, 18 Apr 2024 11:01:07 +0000 (13:01 +0200)]
Merge branch 'net-ipa-header-hygiene'
Alex Elder says:
====================
net: ipa: header hygiene
The end result of this series is that the list of files included in
every IPA source file will be maintained in sorted order. This
imposes some consistency that was previously not possible.
If an IPA header file requires a symbol or type declared in another
header, that other header must be included. E.g., if bool or u32
type is used in a function declaration in an IPA header file, the
IPA header must include <linux/types.h>.
If a type used is just a struct or union *pointer* or enum type (and
no members within these types are needed), then these types only need
to be *declared* within the header that uses it.
This is sufficient, but in addition, this series removes includes of
files that aren't necessary, as well as unneeded type declarations.
====================
Alex Elder [Tue, 16 Apr 2024 23:10:17 +0000 (18:10 -0500)]
net: ipa: more include file cleanup
All of the config data files and all of the register definition
files (plus a few others) use GSI_EE_AP, which is defined in
"ipa_version.h". Include that header where it's needed.
All of the IPA register definition files include "../ipa.h", though
none of them need anything defined there. Similarly, all of the GSI
register definition files include "../gsi.h", but don't need anything
defined there. Remove these unnneded includes.
All of the configuration data files include "../gsi.h", though none
of them need anything defined there, so remove these includes.
Remove other includes of local header files that are not required.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder [Tue, 16 Apr 2024 23:10:16 +0000 (18:10 -0500)]
net: ipa: eliminate unneeded struct declarations
As definitions in headers have been moved around, some of the
struct and enum declarations found in header files have become
no longer necessary and can be removed. Remove these unneeded
declarations.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder [Tue, 16 Apr 2024 23:10:15 +0000 (18:10 -0500)]
net: ipa: add some needed struct declarations
Declare some structure types in a few header files where functions
declared therein use them:
- Functions are declared in "gsi_private.h" that use gsi, gsi_ring, and
gsi_trans structure pointers.
- A gsi_trans struct pointer is passed to two functions
declared in "ipa_endpoint.h"
- In "ipa_interrupt.h", a platform_device pointer is passed in the
declaration for ipa_interrupt_init().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder [Tue, 16 Apr 2024 23:10:14 +0000 (18:10 -0500)]
net: ipa: include "ipa_interrupt.h" where needed
The IPA structure contains an ipa_interrupt structure pointer, and
that structure is declared in "ipa.h". There is no need to include
"ipa_interrupt.h" in that header file.
Instead, include "ipa_interrupt.h" in the three source files (in
addition to "ipa_main.c") that actually use the functions that are
declared there.
Similarly, three files use symbols defined in "ipa_reg.h" but do not
include that file; include it.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder [Tue, 16 Apr 2024 23:10:13 +0000 (18:10 -0500)]
net: ipa: remove unneeded standard includes
Some IPA header files include one or more other standard header
files despite not directly needing anything defined in the included
files. Remove these unnecessary includes.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder [Tue, 16 Apr 2024 23:10:12 +0000 (18:10 -0500)]
net: ipa: include some standard header files
Some IPA header files use types defined in <linux/types.h>, but do
not include that file:
- In "ipa_mem.h", the ipa_mem structure has u16 and u32 fields
- In "ipa_power.h", ipa_power_retention() takes a bool argument,
and ipa_core_clock_rate() returns u32
- In "ipa_version.h", ipa_version_supported() returns bool
Include it in these files to satisfy their dependencies.
The ipa_qmi structure (defined in "ipa_qmi.h") contains a work
structure, so include <linux/workqueue.h> in there.
All of the data and register definition files, as well as "reg.h",
use the ARRAY_SIZE() macro. Include <linux/array_size.h> everywhere
it's used.
Similarly, all register definition files (and a few others) use the
GENMASK() macro, so include <linux/bits.h> to ensure it's defined
where used. BIT() becomes available by including this file also.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Nick Child [Tue, 16 Apr 2024 16:41:28 +0000 (11:41 -0500)]
ibmvnic: Return error code on TX scrq flush fail
In ibmvnic_xmit() if ibmvnic_tx_scrq_flush() returns H_CLOSED then
it will inform upper level networking functions to disable tx
queues. H_CLOSED signals that the connection with the vnic server is
down and a transport event is expected to recover the device.
Previously, ibmvnic_tx_scrq_flush() was hard-coded to return success.
Therefore, the queues would remain active until ibmvnic_cleanup() is
called within do_reset().
The problem is that do_reset() depends on the RTNL lock. If several
ibmvnic devices are resetting then there can be a long wait time until
the last device can grab the lock. During this time the tx/rx queues
still appear active to upper level functions.
FYI, we do make a call to netif_carrier_off() outside the RTNL lock but
its calls to dev_deactivate() are also dependent on the RTNL lock.
As a result, large amounts of retransmissions were observed in a short
period of time, eventually leading to ETIMEOUT. This was specifically
seen with HNV devices, likely because of even more RTNL dependencies.
Therefore, ensure the return code of ibmvnic_tx_scrq_flush() is
propagated to the xmit function to allow for an earlier (and lock-less)
response to a transport event.
Zheng Li [Tue, 16 Apr 2024 09:53:43 +0000 (17:53 +0800)]
neighbour: guarantee the localhost connections be established successfully even the ARP table is full
Inter-process communication on localhost should be established successfully
even the ARP table is full, many processes on server machine use the
localhost to communicate such as command-line interface (CLI),
servers hope all CLI commands can be executed successfully even the arp
table is full. Right now CLI commands got timeout when the arp table is
full. Set the parameter of exempt_from_gc to be true for LOOPBACK net
device to keep localhost neigh in arp table, not removed by gc.
the steps of reproduced:
server with "gc_thresh3 = 1024" setting, ping server from more than 1024
same netmask Lan IPv4 addresses, run "ssh localhost" on console interface,
then the command will get timeout.
These patches fix bugs found during recent work on the ravb driver.
Patches 1 & 2 affect the R-Car code paths so have been tested on an
R-Car M3N Salvator-XS board - this is the only R-Car board I currently
have access to.
Patches 2, 3 & 4 affect the GbEth code paths so have been tested on
RZ/G2L and RZ/G2UL SMARC EVK boards.
Changes v2->v3:
* Incorporate feedback from Niklas and add Reviewed-by tag to patch
"net: ravb: Count packets instead of descriptors in R-Car RX path".
Changes v1->v2:
* Fixed typos in commit message of patch
"net: ravb: Allow RX loop to move past DMA mapping errors".
* Added Sergey's Reviewed-by tags.
* Expanded Cc list as Patchwork complained that I had missed people.
* Trimmed the call trace in accordance with the docs [1] in patch
"net: ravb: Fix GbEth jumbo packet RX checksum handling".
Paul Barker [Tue, 16 Apr 2024 12:02:54 +0000 (13:02 +0100)]
net: ravb: Fix RX byte accounting for jumbo packets
The RX byte accounting for jumbo packets was changed to fix a potential
use-after-free bug. However, that fix used the wrong variable and so
only accounted for the number of bytes in the final descriptor, not the
number of bytes in the whole packet.
To fix this, we can simply update our stats with the correct number of
bytes before calling napi_gro_receive().
Also rename pkt_len to desc_len in ravb_rx_gbeth() to avoid any future
confusion. The variable name pkt_len is correct in ravb_rx_rcar() as
that function does not handle packets spanning multiple descriptors.
Fixes: 5a5a3e564de6 ("ravb: Fix potential use-after-free in ravb_rx_gbeth()") Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sending a 7kB ping packet to the RZ/G2L in v6.9-rc2 causes the following
backtrace:
WARNING: CPU: 0 PID: 0 at include/linux/skbuff.h:3127 skb_trim+0x30/0x38
Hardware name: Renesas SMARC EVK based on r9a07g044l2 (DT)
pc : skb_trim+0x30/0x38
lr : ravb_rx_csum_gbeth+0x40/0x90
Call trace:
skb_trim+0x30/0x38
ravb_rx_gbeth+0x56c/0x5cc
ravb_poll+0xa0/0x204
__napi_poll+0x38/0x17c
This is caused by ravb_rx_gbeth() calling ravb_rx_csum_gbeth() with the
wrong skb for a packet which spans multiple descriptors. To fix this,
use the correct skb.
Fixes: c2da9408579d ("ravb: Add Rx checksum offload support for GbEth") Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paul Barker [Tue, 16 Apr 2024 12:02:52 +0000 (13:02 +0100)]
net: ravb: Allow RX loop to move past DMA mapping errors
The RX loops in ravb_rx_gbeth() and ravb_rx_rcar() skip to the next loop
iteration if a zero-length descriptor is seen (indicating a DMA mapping
error). However, the current RX descriptor index `priv->cur_rx[q]` was
incremented at the end of the loop and so would not be incremented when
we skip to the next loop iteration. This would cause the loop to keep
seeing the same zero-length descriptor instead of moving on to the next
descriptor.
As the loop counter `i` still increments, the loop would eventually
terminate so there is no risk of being stuck here forever - but we
should still fix this to avoid wasting cycles.
To fix this, the RX descriptor index is incremented at the top of the
loop, in the for statement itself. The assignments of `entry` and `desc`
are brought into the loop to avoid the need for duplication.
Fixes: d8b48911fd24 ("ravb: fix ring memory allocation") Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paul Barker [Tue, 16 Apr 2024 12:02:51 +0000 (13:02 +0100)]
net: ravb: Count packets instead of descriptors in R-Car RX path
The units of "work done" in the RX path should be packets instead of
descriptors.
Descriptors which are used by the hardware to record error conditions or
are empty in the case of a DMA mapping error should not count towards
our RX work budget.
Also make the limit variable unsigned as it can never be negative.
Felix Fietkau [Tue, 16 Apr 2024 08:23:29 +0000 (10:23 +0200)]
net: ethernet: mtk_eth_soc: fix WED + wifi reset
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Jakub Kicinski [Thu, 18 Apr 2024 01:38:34 +0000 (18:38 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-04-16 (ice)
This series contains updates to ice driver only.
Michal fixes a couple of issues with TC filter parsing; always add match
for src_vsi and remove flag check that could prevent addition of valid
filters.
Marcin adds additional checks for unsupported flower filters.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix checking for unsupported keys on non-tunnel device
ice: tc: allow zero flags in parsing tc flower
ice: tc: check src_vsi in case of traffic from VF
====================
net: dsa: xrs700x: provide own phylink MAC operations
Convert xrs700x to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
net: dsa: rzn1_a5psw: provide own phylink MAC operations
Convert rzn1_a5psw to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide a stub for
the mac_config() method which is mandatory.
net: dsa: lan9303: provide own phylink MAC operations
Convert lan9303 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
Adrian Moreno [Tue, 16 Apr 2024 09:09:13 +0000 (11:09 +0200)]
selftests: openvswitch: Fix escape chars in regexp.
Character sequences starting with `\` are interpreted by python as
escaped Unicode characters. However, they have other meaning in
regular expressions (e.g: "\d").
It seems Python >= 3.12 starts emitting a SyntaxWarning when these
escaped sequences are not recognized as valid Unicode characters.
Merge tag 'for-6.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fixup in zoned mode for out-of-order writes of metadata that are no
longer necessary, this used to be tracked in a separate list but now
the old locaion needs to be zeroed out, also add assertions
- fix bulk page allocation retry, this may stall after first failure
for compression read/write
* tag 'for-6.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: do not wait for short bulk allocation
btrfs: zoned: add ASSERT and WARN for EXTENT_BUFFER_ZONED_ZEROOUT handling
btrfs: zoned: do not flag ZEROOUT on non-dirty extent buffer
Eric Dumazet [Mon, 15 Apr 2024 21:07:28 +0000 (18:07 -0300)]
net/sched: Fix mirred deadlock on device recursion
When the mirred action is used on a classful egress qdisc and a packet is
mirrored or redirected to self we hit a qdisc lock deadlock.
See trace below.
[..... other info removed for brevity....]
[ 82.890906]
[ 82.890906] ============================================
[ 82.890906] WARNING: possible recursive locking detected
[ 82.890906] 6.8.0-05205-g77fadd89fe2d-dirty #213 Tainted: G W
[ 82.890906] --------------------------------------------
[ 82.890906] ping/418 is trying to acquire lock:
[ 82.890906] ffff888006994110 (&sch->q.lock){+.-.}-{3:3}, at:
__dev_queue_xmit+0x1778/0x3550
[ 82.890906]
[ 82.890906] but task is already holding lock:
[ 82.890906] ffff888006994110 (&sch->q.lock){+.-.}-{3:3}, at:
__dev_queue_xmit+0x1778/0x3550
[ 82.890906]
[ 82.890906] other info that might help us debug this:
[ 82.890906] Possible unsafe locking scenario:
[ 82.890906]
[ 82.890906] CPU0
[ 82.890906] ----
[ 82.890906] lock(&sch->q.lock);
[ 82.890906] lock(&sch->q.lock);
[ 82.890906]
[ 82.890906] *** DEADLOCK ***
[ 82.890906]
[..... other info removed for brevity....]
Example setup (eth0->eth0) to recreate
tc qdisc add dev eth0 root handle 1: htb default 30
tc filter add dev eth0 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth0
Another example(eth0->eth1->eth0) to recreate
tc qdisc add dev eth0 root handle 1: htb default 30
tc filter add dev eth0 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth1
tc qdisc add dev eth1 root handle 1: htb default 30
tc filter add dev eth1 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth0
We fix this by adding an owner field (CPU id) to struct Qdisc set after
root qdisc is entered. When the softirq enters it a second time, if the
qdisc owner is the same CPU, the packet is dropped to break the loop.
Reported-by: Mingshuai Ren <renmingshuai@huawei.com> Closes: https://lore.kernel.org/netdev/20240314111713.5979-1-renmingshuai@huawei.com/ Fixes: 3bcb846ca4cf ("net: get rid of spin_trylock() in net_tx_action()") Fixes: e578d9c02587 ("net: sched: use counter to break reclassify loops") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20240415210728.36949-1-victor@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the net usb qmi_wwan driver to support Longsung U8300/U9300.
Enabling DTR on this modem was necessary to ensure stable operation.
For U8300
Interface 4 is used by for QMI interface in stock firmware of U8300, the
router which uses U8300 modem. Free the interface up, to rebind it to
qmi_wwan driver.
Interface 5 is used by for ADB interface in stock firmware of U8300, the
router which uses U8300 modem. Free the interface up.
The proper configuration is:
Interface mapping is:
0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB
Interface 1 is used by for ADB interface in stock firmware of U9300, the
router which uses U9300 modem. Free the interface up.
Interface 4 is used by for QMI interface in stock firmware of U9300, the
router which uses U9300 modem. Free the interface up, to rebind it to
qmi_wwan driver.
The proper configuration is:
Interface mapping is:
0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI
Note: Interface 3 of some models of the U9300 series can send AT commands.
Jakub Kicinski [Thu, 11 Apr 2024 19:05:34 +0000 (12:05 -0700)]
selftests: adopt BPF's approach to quieter builds
selftest build is fairly noisy, it's easy to miss warnings.
It's standard practice to add alternative messages in
the Makefile. I was grepping for existing solutions,
and found that bpf already has the right knobs.
Move them to lib.mk and adopt in net.
Convert the basic rules in lib.mk.
netfilter: nf_tables: fix memleak in map from abort path
The delete set command does not rely on the transaction object for
element removal, therefore, a combination of delete element + delete set
from the abort path could result in restoring twice the refcount of the
mapping.
Check for inactive element in the next generation for the delete element
command in the abort path, skip restoring state if next generation bit
has been already cleared. This is similar to the activate logic using
the set walk iterator.
Andy Shevchenko [Wed, 17 Apr 2024 14:19:13 +0000 (17:19 +0300)]
gpiolib: swnode: Remove wrong header inclusion
The flags in the software node properties are supposed to be
the GPIO lookup flags, which are provided by gpio/machine.h,
as the software nodes are the kernel internal thing and doesn't
need to rely to any of ABIs.
Fixes: e7f9ff5dc90c ("gpiolib: add support for software nodes") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Merge tag 'pwm/for-6.9-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"The first patch fixes a regression in the suspend/resume path for the
dwc pwm driver that was introduced in v6.9-rc1 when support for 16
channel devices was added.
The second patch fixes a bunch of device tree binding check warnings"
* tag 'pwm/for-6.9-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
dt-bindings: pwm: mediatek,pwm-disp: Document power-domains property
pwm: dwc: allow suspend/resume for 16 channels
Marcin Szycik [Thu, 4 Apr 2024 14:04:51 +0000 (16:04 +0200)]
ice: Add automatic VF reset on Tx MDD events
In cases when VF sends malformed packets that are classified as malicious,
it can cause Tx queue to freeze as a result of Malicious Driver Detection
event. Such malformed packets can appear as a result of a faulty userspace
app running on VF. This frozen queue can be stuck for several minutes being
unusable.
User might prefer to immediately bring the VF back to operational state
after such event, which can be done by automatically resetting the VF which
caused MDD. This is already implemented for Rx events (mdd-auto-reset-vf
flag private flag needs to be set).
Extend the VF auto reset to also cover Tx MDD events. When any MDD event
occurs on VF (Tx or Rx) and the mdd-auto-reset-vf private flag is set,
perform a graceful VF reset to quickly bring it back to operational state.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Co-developed-by: Liang-Min Wang <liang-min.wang@intel.com> Signed-off-by: Liang-Min Wang <liang-min.wang@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
netfilter: nf_tables: restore set elements when delete set fails
From abort path, nft_mapelem_activate() needs to restore refcounters to
the original state. Currently, it uses the set->ops->walk() to iterate
over these set elements. The existing set iterator skips inactive
elements in the next generation, this does not work from the abort path
to restore the original state since it has to skip active elements
instead (not inactive ones).
This patch moves the check for inactive elements to the set iterator
callback, then it reverses the logic for the .activate case which
needs to skip active elements.
Toggle next generation bit for elements when delete set command is
invoked and call nft_clear() from .activate (abort) path to restore the
next generation bit.
The splat below shows an object in mappings memleak:
Fixes: 628bd3e49cba ("netfilter: nf_tables: drop map element references from preparation phase") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
platform/x86/amd/pmc: Extend Framework 13 quirk to more BIOSes
BIOS 03.05 still hasn't fixed the spurious IRQ1 issue. As it's still
being worked on there is still a possibility that it won't need to
apply to future BIOS releases.
Add a quirk for BIOS 03.05 as well.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240410141046.433-1-mario.limonciello@amd.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Eric Dumazet [Tue, 16 Apr 2024 09:50:54 +0000 (09:50 +0000)]
tcp: accept bare FIN packets under memory pressure
Andrew Oates reported that some macOS hosts could repeatedly
send FIN packets even if the remote peer drops them and
send back DUP ACK RWIN 0 packets.
<quoting Andrew>
20:27:16.968254 gif0 In IP macos > victim: Flags [SEW], seq 1950399762, win 65535, options [mss 1460,nop,wscale 6,nop,nop,TS val 501897188 ecr 0,sackOK,eol], length 0
20:27:16.968339 gif0 Out IP victim > macos: Flags [S.E], seq 2995489058, ack 1950399763, win 1448, options [mss 1460,sackOK,TS val 3829877593 ecr 501897188,nop,wscale 0], length 0
20:27:16.968833 gif0 In IP macos > victim: Flags [.], ack 1, win 2058, options [nop,nop,TS val 501897188 ecr 3829877593], length 0
20:27:16.968885 gif0 In IP macos > victim: Flags [P.], seq 1:1449, ack 1, win 2058, options [nop,nop,TS val 501897188 ecr 3829877593], length 1448
20:27:16.968896 gif0 Out IP victim > macos: Flags [.], ack 1449, win 0, options [nop,nop,TS val 3829877593 ecr 501897188], length 0
20:27:19.454593 gif0 In IP macos > victim: Flags [F.], seq 1449, ack 1, win 2058, options [nop,nop,TS val 501899674 ecr 3829877593], length 0
20:27:19.454675 gif0 Out IP victim > macos: Flags [.], ack 1449, win 0, options [nop,nop,TS val 3829880079 ecr 501899674], length 0
20:27:19.455116 gif0 In IP macos > victim: Flags [F.], seq 1449, ack 1, win 2058, options [nop,nop,TS val 501899674 ecr 3829880079], length 0
The retransmits/dup-ACKs then repeat in a tight loop.
</quoting Andrew>
RFC 9293 3.4. Sequence Numbers states :
Note that when the receive window is zero no segments should be
acceptable except ACK segments. Thus, it is be possible for a TCP to
maintain a zero receive window while transmitting data and receiving
ACKs. However, even when the receive window is zero, a TCP must
process the RST and URG fields of all incoming segments.
Even if we could consider a bare FIN.ACK packet to be an ACK in RFC terms,
the retransmits should use exponential backoff.
Accepting the FIN in linux does not add extra memory costs,
because the FIN flag will simply be merged to the tail skb in
the receive queue, and incoming packet is freed.
Reported-by: Andrew Oates <aoates@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Christoph Paasch <cpaasch@apple.com> Cc: Vidhi Goel <vidhi_goel@apple.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since [1], dma_alloc_coherent() does not accept requests for GFP_COMP
anymore, even on archs that may be able to fulfill this. Functionality that
relied on the receive buffer being a compound page broke at that point:
The SMC-D protocol, that utilizes the ism device driver, passes receive
buffers to the splice processor in a struct splice_pipe_desc with a
single entry list of struct pages. As the buffer is no longer a compound
page, the splice processor now rejects requests to handle more than a
page worth of data.
Replace dma_alloc_coherent() and allocate a buffer with folio_alloc and
create a DMA map for it with dma_map_page(). Since only receive buffers
on ISM devices use DMA, qualify the mapping as FROM_DEVICE.
Since ISM devices are available on arch s390, only, and on that arch all
DMA is coherent, there is no need to introduce and export some kind of
dma_sync_to_cpu() method to be called by the SMC-D protocol layer.
Analogously, replace dma_free_coherent by a two step dma_unmap_page,
then folio_put to free the receive buffer.
Fixes: c08004eede4b ("s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent") Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
random: handle creditable entropy from atomic process context
The entropy accounting changes a static key when the RNG has
initialized, since it only ever initializes once. Static key changes,
however, cannot be made from atomic context, so depending on where the
last creditable entropy comes from, the static key change might need to
be deferred to a worker.
Previously the code used the execute_in_process_context() helper
function, which accounts for whether or not the caller is
in_interrupt(). However, that doesn't account for the case where the
caller is actually in process context but is holding a spinlock.
This turned out to be the case with input_handle_event() in
drivers/input/input.c contributing entropy:
According to Guoyong, it's not really possible to refactor the various
drivers to never hold a spinlock there. And in_atomic() isn't reliable.
So, rather than trying to be too fancy, just punt the change in the
static key to a workqueue always. There's basically no drawback of doing
this, as the code already needed to account for the static key not
changing immediately, and given that it's just an optimization, there's
not exactly a hurry to change the static key right away, so deferal is
fine.
Reported-by: Guoyong Wang <guoyong.wang@mediatek.com> Cc: stable@vger.kernel.org Fixes: f5bda35fba61 ("random: use static branch for crng_ready()") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Yujie Liu [Tue, 16 Apr 2024 05:32:10 +0000 (13:32 +0800)]
selftests: fix netfilter path in Makefile
Netfilter tests have been moved to a subdir under selftests/net by
patch series [1]. Fix the path in selftests/Makefile accordingly.
This helps fix the following error:
tools/testing/selftests$ make
...
make[1]: Entering directory 'tools/testing/selftests'
make[1]: *** netfilter: No such file or directory. Stop.
make[1]: Leaving directory 'tools/testing/selftests'
projects / mirror_ubuntu-kernels.git / log