Cc: Frans Pop <elendil@planet.nl> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Len Brown <lenb@kernel.org> Acked-by: Matthew Garrett <mjg@redhat.com> Reported-by: Helge Deller <deller@gmx.de> Testted-by: Helge Deller <deller@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 4 Feb 2009 23:12:06 +0000 (15:12 -0800)]
revert "rlimit: permit setting RLIMIT_NOFILE to RLIM_INFINITY"
Revert commit 0c2d64fb6cae9aae480f6a46cfe79f8d7d48b59f because it causes
(arguably poorly designed) existing userspace to spend interminable
periods closing billions of not-open file descriptors.
We could bring this back, with some sort of opt-in tunable in /proc, which
defaults to "off".
Peter's alanysis follows:
: I spent several hours trying to get to the bottom of a serious
: performance issue that appeared on one of our servers after upgrading to
: 2.6.28. In the end it's what could be considered a userspace bug that
: was triggered by a change in 2.6.28. Since this might also affect other
: people I figured I'd at least document what I found here, and maybe we
: can even do something about it:
:
:
: So, I upgraded some of debian.org's machines to 2.6.28.1 and immediately
: the team maintaining our ftp archive complained that one of their
: scripts that previously ran in a few minutes still hadn't even come
: close to being done after an hour or so. Downgrading to 2.6.27 fixed
: that.
:
: Turns out that script is forking a lot and something in it or python or
: whereever closes all the file descriptors it doesn't want to pass on.
: That is, it starts at zero and goes up to ulimit -n/RLIMIT_NOFILE and
: closes them all with a few exceptions.
:
: Turns out that takes a long time when your limit -n is now 2^20 (1048576).
:
: With 2.6.27.* the ulimit -n was the standard 1024, but with 2.6.28 it is
: now a thousand times that.
:
: 2.6.28 included a patch titled "rlimit: permit setting RLIMIT_NOFILE to
: RLIM_INFINITY" (0c2d64fb6cae9aae480f6a46cfe79f8d7d48b59f)[1] that
: allows, as the title implies, to set the limit for number of files to
: infinity.
:
: Closer investigation showed that the broken default ulimit did not apply
: to "system" processes (like stuff started from init). In the end I
: could establish that all processes that passed through pam_limit at one
: point had the bad resource limit.
:
: Apparently the pam library in Debian etch (4.0) initializes the limits
: to some default values when it doesn't have any settings in limit.conf
: to override them. Turns out that for nofiles this is RLIM_INFINITY.
: Commenting out "case RLIMIT_NOFILE" in pam_limit.c:267 of our pam
: package version 0.79-5 fixes that - tho I'm not sure what side effects
: that has.
:
: Debian lenny (the upcoming 5.0 version) doesn't have this issue as it
: uses a different pam (version).
Reported-by: Peter Palfrader <weasel@debian.org> Cc: Adam Tkac <vonsch@gmail.com> Cc: Michael Kerrisk <mtk.manpages@googlemail.com> Cc: <stable@kernel.org> [2.6.28.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Battersby [Wed, 4 Feb 2009 23:12:04 +0000 (15:12 -0800)]
shm: fix shmctl(SHM_INFO) lockup with !CONFIG_SHMEM
shm_get_stat() assumes that the inode is a "struct shmem_inode_info",
which is incorrect for !CONFIG_SHMEM (see fs/ramfs/inode.c:
ramfs_get_inode() vs. mm/shmem.c: shmem_get_inode()).
This bad assumption can cause shmctl(SHM_INFO) to lockup when
shm_get_stat() tries to spin_lock(&info->lock). Users of !CONFIG_SHMEM
may encounter this lockup simply by invoking the 'ipcs' command.
Reported by Jiri Olsa back in February 2008:
http://lkml.org/lkml/2008/2/29/74
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Cc: Jiri Kosina <jkosina@suse.cz> Reported-by: Jiri Olsa <olsajiri@gmail.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: <stable@kernel.org> [2.6.everything] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea Righi [Wed, 4 Feb 2009 23:12:03 +0000 (15:12 -0800)]
fbmem: don't call copy_from/to_user() with mutex held
Avoid calling copy_from/to_user() with fb_info->lock mutex held in fbmem
ioctl().
fb_mmap() is called under mm->mmap_sem (A) held, that also acquires
fb_info->lock (B); fb_ioctl() takes fb_info->lock (B) and does
copy_from/to_user() that might acquire mm->mmap_sem (A), causing a
deadlock.
NOTE: it doesn't push down the fb_info->lock in each own driver's
fb_ioctl(), so there are still potential deadlocks elsewhere.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com> Cc: Dave Jones <davej@redhat.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Johannes Weiner <hannes@saeurebad.de> Cc: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Harvey Harrison <harvey.harrison@gmail.com> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 4 Feb 2009 23:12:01 +0000 (15:12 -0800)]
rtc: rtc-dm355evm driver
Simple RTC driver for the MSP430 firmware on the DM355 EVM board. Other
than not supporting atomic reads/writes of all four bytes, this is
reasonable as a basic no-alarm RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Garrett [Wed, 4 Feb 2009 23:12:00 +0000 (15:12 -0800)]
misc: dell-laptop should depend on POWER_SUPPLY
dell-laptop makes use of the power supply class information to choose
which backlight interface to change. Add a depends on it.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Wed, 4 Feb 2009 23:11:59 +0000 (15:11 -0800)]
generic swap(): don't return a value from swap()
The swap() macro is accidentally retuning the value of its first argument.
Change it into a doesn't-return-anything macro before someone goes and
relies upon this behaviour.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Wu Fengguang <wfg@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Altobelli [Wed, 4 Feb 2009 23:11:58 +0000 (15:11 -0800)]
hpilo: open/close fix
The device can take a while to respond to an open/close request, so
increase the time kernel will wait for response (1 ms to 10ms).
Also, properly clean up a channel on a failed open, by calling the channel
close routine. Just freeing the memory isn't sufficient, the device needs
to be informed that the channel is no longer open, and the device memory
cleared of references to freed dma buffer.
Signed-off-by: David Altobelli <david.altobelli@hp.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 4 Feb 2009 23:11:58 +0000 (15:11 -0800)]
kernel/async.c: fix printk warnings
alpha:
kernel/async.c: In function 'run_one_entry':
kernel/async.c:141: warning: format '%lli' expects type 'long long int', but argument 2 has type 'async_cookie_t'
kernel/async.c:149: warning: format '%lli' expects type 'long long int', but argument 2 has type 'async_cookie_t'
kernel/async.c:149: warning: format '%lld' expects type 'long long int', but argument 4 has type 's64'
kernel/async.c: In function 'async_synchronize_cookie_special':
kernel/async.c:250: warning: format '%lli' expects type 'long long int', but argument 3 has type 's64'
Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 4 Feb 2009 21:58:50 +0000 (13:58 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: APIC: enable workaround on AMD Fam10h CPUs
xen: disable interrupts before saving in percpu
x86: add x86@kernel.org to MAINTAINERS
x86: push old stack address on irqstack for unwinder
irq, x86: fix lock status with numa_migrate_irq_desc
x86: add cache descriptors for Intel Core i7
x86/Voyager: make it build and boot
Linus Torvalds [Wed, 4 Feb 2009 17:39:12 +0000 (09:39 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: pcm_oss: AFMT_S24_LE is set twice in return value
ALSA: ASoC: email - update email addresses.
OMAP: ASoC: Fix spinlock misuse in omap-pcm.c
ALSA: hda - No widget selection for volume knob widgets in proc output
ALSA: hda - Add support of iMac 24 Aluminium
ALSA: alsa: time reaches -1, tested 0
ALSA: hda - Add quirk for another HP dv5 model
Linus Torvalds [Wed, 4 Feb 2009 15:56:25 +0000 (07:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (40 commits)
Blackfin arch: Remove outdated code
Blackfin arch: Fix udelay implementation
Blackfin arch: Update Copyright information
Blackfin arch: Add BF561 PPI POLS, POLC Masks
Blackfin arch: Update CM-BF527 kernel config
Blackfin arch: define bfin_memmap as static since it is only used here
Blackfin arch: cplb mananger: use a do...while loop rather than a for loop
Blackfin arch: fix bug - traps test case 19 for exception 0x2d fails
Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Blackfin arch: build jtag tty driver as a module by default
Blackfin arch: fix 2 bugs related to debug
Blackfin arch: Add ANOMALY_05000380 to BF54x to kill the compile warning
Blackfin arch: Fix bug - 561 SMP kernel can't boot from jffs2
Blackfin arch: base SIC_IWR# programming on whether the MMR exists
Blackfin arch: read SYSCR on newer parts that mirror the bits of SWRST in it
Blackfin arch: fixup board init function name
Blackfin arch: drop CONFIG_I2C_BOARDINFO ifdefs
Blackfin arch: bfin_reset->_bfin_reset redirection no longer needed
Blackfin arch: sync reboot handler with version in u-boot
Blackfin arch: Faster Implementation of csum_tcpudp_nofold()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Kill bogus TPC/address truncation during 32-bit faults.
sparc: fixup for sparseirq changes
sparc64: Validate kernel generated fault addresses on sparc64.
sparc64: On non-Niagara, need to touch NMI watchdog in NOHZ mode.
sparc64: Implement NMI watchdog on capable cpus.
sparc: Probe PMU type and record in sparc_pmu_type.
sparc64: Move generic PCR support code to seperate file.
The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.
Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Mike Frysinger [Wed, 4 Feb 2009 08:49:45 +0000 (16:49 +0800)]
Blackfin arch: cplb mananger: use a do...while loop rather than a for loop
use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Blackfin arch: Faster Implementation of csum_tcpudp_nofold()
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Sonic Zhang [Wed, 4 Feb 2009 08:49:45 +0000 (16:49 +0800)]
Blackfin arch: Fix bug - Run "reboot" hangs bf518-ezbrd
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Blackfin arch: explicit add a might sleep to gpio_free
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the blackfin
architecture.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@strlen.de> Cc: David Brownell <david-b@pacbell.net> Acked-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Blackfin arch: reset POLAR setting when acquiring a gpio for the first time
when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state. this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.
when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state. this
should occur if the GPIO has not been allocated in any other way.
some examples:
- when doing something like "request_irq(); gpio_request();" on the
same GPIO, the POLAR setting should not be reset.
- when doing "gpio_request(); gpio_request();" on the same GPIO, the
POLAR setting should be reset only the first time and not the second.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Blackfin arch: Fix Bug - Kernel does not boot if re-program clocks
On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Borislav Petkov [Tue, 3 Feb 2009 15:24:22 +0000 (16:24 +0100)]
x86: APIC: enable workaround on AMD Fam10h CPUs
Impact: fix to enable APIC for AMD Fam10h on chipsets with a missing/b0rked
ACPI MP table (MADT)
Booting a 32bit kernel on an AMD Fam10h CPU running on chipsets with
missing/b0rked MP table leads to a hang pretty early in the boot process
due to the APIC not being initialized. Fix that by falling back to the
default APIC base address in 32bit code, as it is done in the 64bit
codepath.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
xen_mc_batch has a small preempt race where it takes the address of a
percpu variable immediately before disabling interrupts, thereby
leaving a small window in which we may migrate to another cpu and save
the flags in the wrong percpu variable. Disable interrupts before
saving the old flags in a percpu.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It made the following changes:
1. Decrement wbc->nr_to_write instead of nr_to_write
2. Decrement wbc->nr_to_write _only_ if wbc->sync_mode == WB_SYNC_NONE
3. If synced nr_to_write pages, stop only if if wbc->sync_mode ==
WB_SYNC_NONE, otherwise keep going.
However, according to the commit message, the intention was to only make
change 3. Change 1 is a bug. Change 2 does not seem to be necessary,
and it breaks UBIFS expectations, so if needed, it should be done
separately later. And change 2 does not seem to be documented in the
commit message.
This patch does the following:
1. Undo changes 1 and 2
2. Add a comment explaining change 3 (it very useful to have comments
in _code_, not only in the commit).
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Acked-by: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 4 Feb 2009 00:52:44 +0000 (16:52 -0800)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: remove fast unmounting
UBIFS: return sensible error codes
UBIFS: remount ro fixes
UBIFS: spelling fix 'date' -> 'data'
UBIFS: sync wbufs after syncing inodes and pages
UBIFS: fix LPT out-of-space bug (again)
UBIFS: fix no_chk_data_crc
UBIFS: fix assertions
UBIFS: ensure orphan area head is initialized
UBIFS: always clean up GC LEB space
UBIFS: add re-mount debugging checks
UBIFS: fix LEB list freeing
UBIFS: simplify locking
UBIFS: document dark_wm and dead_wm better
UBIFS: do not treat all data as short term
UBIFS: constify operations
UBIFS: do not commit twice
Linus Torvalds [Wed, 4 Feb 2009 00:50:20 +0000 (16:50 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: add quota call to ocfs2_remove_btree_range()
ocfs2: Wakeup the downconvert thread after a successful cancel convert
ocfs2: Access the xattr bucket only before modifying it.
configfs: Silence lockdep on mkdir(), rmdir() and configfs_depend_item()
ocfs2: Fix possible deadlock in ocfs2_write_dquot()
ocfs2: Push out dropping of dentry lock to ocfs2_wq
Linus Torvalds [Wed, 4 Feb 2009 00:49:54 +0000 (16:49 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
[XFS] Warn on transaction in flight on read-only remount
xfs: Check buffer lengths in log recovery
don't reallocate sxp variable passed into xfs_swapext
Upon further consideration, we actually should never see any
fault addresses for 32-bit tasks with the upper 32-bits set.
If it does every happen, by definition it's a bug. Whatever
context created that fault would only have that fault satisfied
if we used the full 64-bit address. If we truncate it, we'll
always fault the wrong address and we'll always loop faulting
forever.
So catch such conditions and mark them as errors always. Log
the error and fail the fault.
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Tue, 3 Feb 2009 23:18:01 +0000 (15:18 -0800)]
e1000: Fix PCI enable to honor the need_ioport flag
On machine were no IO ports are assigned the call
to pci_enable_device() will fail, even if need_ioport
is false, we need to use pci_enable_device_mem() here.
Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Nelson [Tue, 3 Feb 2009 23:16:17 +0000 (15:16 -0800)]
sgi-xp: link XPNET's net_device_ops to its net_device structure
A recent patch by Stephen Hemminger to convert XPNET to use net_device_ops and
internal net_device_stats failed to link the net_device_ops structure to the
net_device structure. See commit e8ac9c55f28482f5b2f497a8e7eb90985db237c2
("xpnet: convert devices to new API").
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben [Tue, 3 Feb 2009 23:13:26 +0000 (15:13 -0800)]
hso: add new device id's
This patch adds a few device ID's. It also removes an ID that was used
in an internal engineering version of a device and will never see
commercial light. Even if this ID will be 'recycled' in the future,
which is very unlikely, we don't know what kind of device will be
behind it. Therefore it's safer to remove it.
Signed-off-by: Filip Aben <f.aben@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
But we can't use do_each_pid_task() without rcu_read_lock() even if
we know the pid itself can't go away (it was pinned in ftrace_pid_write).
The exiting task can detach itself from this pid at any moment.
Felix Blyakher [Fri, 23 Jan 2009 03:34:05 +0000 (21:34 -0600)]
[XFS] Warn on transaction in flight on read-only remount
Till VFS can correctly support read-only remount without racing,
use WARN_ON instead of BUG_ON on detecting transaction in flight
after quiescing filesystem.
Signed-off-by: Felix Blyakher <felixb@sgi.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Dave Chinner [Thu, 22 Jan 2009 04:37:47 +0000 (15:37 +1100)]
xfs: Check buffer lengths in log recovery
Before trying to obtain, read or write a buffer,
check that the buffer length is actually valid. If
it is not valid, then something read in the recovery
process has been corrupted and we should abort
recovery.
Reported-by: Eric Sesterhenn <snakebyte@gmx.de> Tested-by: Eric Sesterhenn <snakebyte@gmx.de> Reviewed-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Felix Blyakher <felixb@sgi.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
Linus Torvalds [Tue, 3 Feb 2009 15:39:55 +0000 (07:39 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
libata: add no penalty retry request for EH device handling routines
libata: improve probe failure handling
libata: add @spd_limit to sata_down_spd_limit()
libata: clear dev->ering in smarter way
libata: check onlineness before using SPD in sata_down_spd_limit()
libata: move ata_dev_disable() to libata-eh.c
libata: fix EH device failure handling
sata_nv: ck804 has borked hardreset too
ide/libata: fix ata_id_is_cfa() (take 4)
libata: fix kernel-doc warnings
ahci: add a module parameter to ignore the SSS flags for async scanning
sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
[libata] sata_sil: Fix compilation error with libata debugging enabled
Change spin_locks to irqsave to prevent dead-locks.
Protect adding and deleting to/from dca_providers list.
Drop the lock during dca_sysfs_add_req() and dca_sysfs_remove_req() calls
as they might sleep (use GFP_KERNEL allocation).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 3 Feb 2009 07:19:50 +0000 (23:19 -0800)]
cassini/sungem: limit reaches -1, but 0 tested
while (limit--)
if (test())
break;
if (limit <= 0)
goto test_failed;
In the last iteration, limit is decremented after the test to 0.
If just thereafter test() succeeds and a break occurs, the goto
still occurs because limit is 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Feb 2009 06:08:15 +0000 (22:08 -0800)]
sparc64: Validate kernel generated fault addresses on sparc64.
In order to handle all of the cases of address calculation overflow
properly, we run sparc 32-bit processes in "address masking" mode
when running on a 64-bit kernel.
Address masking mode zeros out the top 32-bits of the address
calculated for every load and store instruction.
However, when we're in privileged mode we have to run with that
address masking mode disabled even when accessing userspace from
the kernel.
To "simulate" the address masking mode we clear the top-bits by
hand for 32-bit processes in the fault handler.
It is the responsibility of code in the compat layer to properly
zero extend addresses used to access userspace. If this isn't
followed properly we can get into a fault loop.
Say that the user address is 0xf0000000 but for whatever reason
the kernel code sign extends this to 64-bit, and then the kernel
tries to access the result.
In such a case we'll fault on address 0xfffffffff0000000 but the fault
handler will process that fault as if it were to address 0xf0000000.
We'll loop faulting forever because the fault never gets satisfied.
So add a check specifically for this case, when the kernel is faulting
on a user address access and the addresses don't match up.
This code path is sufficiently slow path, and this bug is sufficiently
painful to diagnose, that this kind of bug check is warranted.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Feb 2009 05:57:48 +0000 (21:57 -0800)]
sparc64: On non-Niagara, need to touch NMI watchdog in NOHZ mode.
When we're idling in NOHZ mode, timer interrupts are not running.
Evidence of processing timer interrupts is what the NMI watchdog
uses to determine if the CPU is stuck.
On Niagara, we'll yield the cpu. This will make the cpu, at
worst, hang out in the hypervisor until an interrupt arrives.
This will prevent the NMI watchdog timer from firing.
However on non-Niagara we just loop executing instructions
which will cause the NMI watchdog to keep firing. It won't
see timer interrupts happening so it will think the cpu is
stuck.
Fix this by touching the NMI watchdog in the cpu idle loop
on non-Niagara machines.
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Hicks [Fri, 30 Jan 2009 16:50:54 +0000 (10:50 -0600)]
x86: push old stack address on irqstack for unwinder
Impact: Fixes dumpstack and KDB on 64 bits
This re-adds the old stack pointer to the top of the irqstack to help
with unwinding. It was removed in commit d99015b1abbad743aa049b439c1e1dede6d0fa49
as part of the save_args out-of-line work.
Both dumpstack and KDB require this information.
Signed-off-by: Martin Hicks <mort@sgi.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:36 +0000 (20:31 +0900)]
libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:35 +0000 (20:31 +0900)]
libata: add no penalty retry request for EH device handling routines
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count. This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions. As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:34 +0000 (20:31 +0900)]
libata: improve probe failure handling
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed. This often leads to consecutive hotplug events
without successful probing.
This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.
As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:33 +0000 (20:31 +0900)]
libata: add @spd_limit to sata_down_spd_limit()
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants. This parameter doesn't get in the way even
when it's too low. The closest possible limit is applied.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:32 +0000 (20:31 +0900)]
libata: clear dev->ering in smarter way
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 Jan 2009 11:31:31 +0000 (20:31 +0900)]
libata: check onlineness before using SPD in sata_down_spd_limit()
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed. Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / mirror_ubuntu-eoan-kernel.git / log