r8169: add check for invalid parameter combination in rtl_set_coalesce
Realtek provided information about a HW constraint that time limit must
not be set to 0 if the frame limit is >0. Add a check for this and
reject invalid parameter combinations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports only frame limits 0, 4, 8, .. 60 internally.
Returning EINVAL for all val % 4 != 0 seems to be a little bit too
unfriendly to the user. Therefore round up the frame limit to the next
supported value. In addition round up the time limit, else a very low
limit could be rounded down to 0, and interpreted as "ignore value"
by the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The time limit provided by userspace is multiplied with 1000,
what could result in an overflow. Therefore change the time limit
parameter unit from ns to us, and avoid the problematic operation.
If there's no matching scale because provided time limit is too big,
return ERANGE instead of EINVAL to provide a hint to the user what's
wrong.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_GET() macro to make the code better readable. In addition
change the logic to round the time limit up, not down. Reason is that
a time limit <1us would be rounded to 0 currently, what would be
interpreted as "no time limit set".
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: don't pass net_device to irq coalescing sub-functions
The net_device argument is just used to get a struct rtl8169_private
pointer via netdev_priv(). Therefore pass the struct rtl8169_private
pointer directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hsr: remove hsr interface if all slaves are removed
When all hsr slave interfaces are removed, hsr interface doesn't work.
At that moment, it's fine to remove an unused hsr interface automatically
for saving resources.
That's a common behavior of virtual interfaces.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Apr 2020 17:35:43 +0000 (10:35 -0700)]
tcp: add hrtimer slack to sack compression
Add a sysctl to control hrtimer slack, default of 100 usec.
This gives the opportunity to reduce system overhead,
and help very short RTT flows.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Apr 2020 17:35:42 +0000 (10:35 -0700)]
tcp: tcp_sack_new_ofo_skb() should be more conservative
Currently, tcp_sack_new_ofo_skb() sends an ack if prior
acks were 'compressed', if room has to be made in tp->selective_acks[]
But there is no guarantee all four sack ranges can be included
in SACK option. As a matter of fact, when TCP timestamps option
is used, only three SACK ranges can be included.
Lets assume only two ranges can be included, and force the ack:
- When we touch more than 2 ranges in the reordering
done if tcp_sack_extend() could be done.
- If we have at least 2 ranges when adding a new one.
This enforces that before a range is in third or fourth
position, at least one ACK packet included it in first/second
position.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Apr 2020 17:35:41 +0000 (10:35 -0700)]
tcp: add tp->dup_ack_counter
In commit 86de5921a3d5 ("tcp: defer SACK compression after DupThresh")
I added a TCP_FASTRETRANS_THRESH bias to tp->compressed_ack in order
to enable sack compression only after 3 dupacks.
Since we plan to relax this rule for flows that involve
stacks not requiring this old rule, this patch adds
a distinct tp->dup_ack_counter.
This means the TCP_FASTRETRANS_THRESH value is now used
in a single location that a future patch can adjust:
if (tp->dup_ack_counter < TCP_FASTRETRANS_THRESH) {
tp->dup_ack_counter++;
goto send_now;
}
This patch also introduces tcp_sack_compress_send_ack()
helper to ease following patch comprehension.
This patch refines LINUX_MIB_TCPACKCOMPRESSED to not
count the acks that we had to send if the timer expires
or tcp_sack_compress_send_ack() is sending an ack.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 Apr 2020 20:15:16 +0000 (13:15 -0700)]
Merge tag 'mlx5-updates-2020-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-04-30
1) Add release all pages support, From Eran.
to release all FW pages at once on driver unload, when supported by FW.
2) From Maxim and Tariq, Trivial Data path cleanup and code improvements
in preparation for their next features, TLS offload and TX performance
improvements
3) Multiple cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: Prepare SPAN API for upcoming changes
Switched port analyzer (SPAN) is used for packet mirroring. Over mlxsw
this is achieved by attaching tc-mirred action to either matchall or
flower classifier.
The current API used to configure SPAN consists of two functions:
mlxsw_sp_span_mirror_add() and mlxsw_sp_span_mirror_del().
These two functions pack a lot of different operations:
* SPAN agent configuration: Determining the egress port and optional
headers that need to encapsulate the mirrored packet (when mirroring
to a gretap, for example)
* Egress mirror buffer configuration: Allocating / freeing a buffer when
port is analyzed (inspected) at egress
* SPAN agent binding: Binding the SPAN agent to a trigger, if any. The
current triggers are incoming / outgoing packet and they are only used
for matchall-based mirroring
This non-modular design makes it difficult to extend the API for future
changes, such as new mirror targets (CPU) and new global triggers (early
dropped packets, for example).
Therefore, this patch set gradually adds APIs for above mentioned
operations and then converts the two existing users to use it instead of
the old API. No functional changes intended. Tested with existing
mirroring selftests.
Patch set overview:
Patches #1-#5 gradually add the new API
Patches #6-#8 convert existing users to use the new API
Patch #9 removes the old API
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_acl: Convert flower-based mirroring to new SPAN API
In flower-based mirroring, mirroring is done with ACLs and the SPAN
agent is not bound to a port. Instead its identifier is specified in an
ACL action.
Convert this type of mirroring to use the new API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Convert matchall-based mirroring to new SPAN API
In matchall-based mirroring, mirroring is not done with ACLs, but a SPAN
agent is bound to the ingress / egress of a port and all incoming /
outgoing traffic is mirrored.
Convert this type of mirroring to use the new API.
First the SPAN agent is resolved, then the port is marked as analyzed
and its egress mirror buffer is potentially allocated. Lastly, the
binding is performed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Add APIs to bind / unbind a SPAN agent
Currently, a SPAN agent can only be bound to a per-port trigger where
the trigger is either an incoming packet (INGRESS) or an outgoing packet
(EGRESS) to / from the port.
A follow-up patch set will introduce the concept of global triggers and
per-{port, TC} enablement. With global triggers, the trigger entry is
only keyed by a trigger and not by a port and a trigger. The trigger can
be, for example, a packet that was early dropped.
While the binding between the SPAN agent and the trigger is performed
only once, the trigger entry needs to be reference counted, as the
trigger can be enabled on multiple ports.
Add APIs to bind / unbind a SPAN agent to a trigger and reference count
the trigger entry in preparation for global triggers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Wrap buffer change in a function
The code that adjusts the egress buffer size is not symmetric at the
moment. The update is done via a call to
mlxsw_sp_span_port_buffer_update(), but the disablement is done inline
by invoking the write to SBIB register directly.
Wrap the disablement code in mlxsw_sp_span_port_buffer_disable().
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Suggested-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will introduce mlxsw_sp_span_port_buffer_disable() function
that disables the egress buffer on an analyzed port. Rename the opposite
function that updates the buffer on an analyzed port accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Suggested-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Add APIs to get / put an analyzed port
An analyzed port is a port whose incoming / outgoing traffic is mirrored
to a SPAN agent and analyzed on a remote server.
A port can be analyzed by multiple tc filters and therefore the
corresponding analyzed port entry needs to be reference counted. This is
significant because ports whose outgoing traffic is analyzed need to
have an egress mirror buffer.
Add APIs to get / put an analyzed port. Allocate an egress mirror buffer
on a port when it is first inspected at egress and free the buffer when
it is no longer inspected at egress.
Protect the list of analyzed ports with a mutex, as a later patch will
traverse it from a context in which RTNL lock is not held.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert timestamping.txt to ReST
- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert tc-actions-env-rules.txt to ReST
- add SPDX header;
- add a document title;
- use the right numbered list markup;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- use copyright symbol;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- mark code blocks and literals as such;
- add a document title;
- adjust chapters, adding proper markups;
- mark lists as such;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- use autonumbered list markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- use copyright symbol;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert radiotap-headers.txt to ReST
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert proc_net_tcp.txt to ReST
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- use bold markups on a few places;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- use copyright symbol;
- add notes markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
This patch has a big diff, but most are due to whitespaces.
Yet, the conversion is similar to other files under networking:
- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title and chapter markups;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- add notes markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- use :field: markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert mac80211-injection.txt to ReST
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
inet_diag: add cgroup attribute and filter
This patch series extends inet diag with cgroup v2 ID attribute and
filter. Which allows investigate sockets on per cgroup basis. Patch for
ss is already sent to iproute2-next mailing list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to filter sockets based on cgroup v2 ID.
Such filter is helpful in ss utility for filtering sockets by
cgroup pathname.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds cgroup v2 ID to common inet diag message attributes.
Cgroup v2 ID is kernfs ID (ino or ino+gen). This attribute allows filter
inet diag output by cgroup ID obtained by name_to_handle_at() syscall.
When net_cls or net_prio cgroup is activated this ID is equal to 1 (root
cgroup ID) for newly created sockets.
Some notes about this ID:
1) gets initialized in socket() syscall
2) incoming socket gets ID from listening socket
(not during accept() syscall)
3) not changed when process get moved to another cgroup
4) can point to deleted cgroup (refcounting)
v2:
- use CONFIG_SOCK_CGROUP_DATA instead if CONFIG_CGROUPS
v3:
- fix attr size by using nla_total_size_64bit() (Eric Dumazet)
- more detailed commit message (Konstantin Khlebnikov)
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-By: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 30 Apr 2020 15:02:53 +0000 (18:02 +0300)]
stmmac: intel: Fix indentation to put on one line affected code
There is no competition to get more LOCs into the kernel, and driver can look
better and have improved readability without those additional line breaks.
While at it, shorten info structures that they are all PCI, at the end it's
a PCI driver for Intel hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 30 Apr 2020 15:02:50 +0000 (18:02 +0300)]
stmmac: intel: Remove unnecessary loop for PCI BARs
Copy'n'paste without thinking is not a good idea and in this case it brought
unnecessary loop over PCI BAR resources which was needed to workaround one of
STMicro RVP boards. Remove unnecessary loops from Intel driver.
Fixes: 58da0cfa6cf1 ("net: stmmac: create dwmac-intel.c to contain all Intel platform") Cc: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 30 Apr 2020 15:02:49 +0000 (18:02 +0300)]
stmmac: intel: Fix clock handling on error and remove paths
clk_prepare_enable() might fail, we have to check its returned value.
Besides that we have to call clk_disable_unprepare() on the error and
remove paths. Do above in the dwmac-intel driver.
While at it, remove leftover in stmmac_pci and remove unneeded condition
for NULL-aware clk_unregister_fixed_rate() call.
Fixes: 58da0cfa6cf1 ("net: stmmac: create dwmac-intel.c to contain all Intel platform") Cc: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 30 Apr 2020 15:02:48 +0000 (18:02 +0300)]
stmmac: intel: Fix kernel crash due to wrong error path
Unfortunately sometimes ->probe() may fail. The commit b9663b7ca6ff
("net: stmmac: Enable SERDES power up/down sequence")
messed up with error handling and thus:
[ 12.811311] ------------[ cut here ]------------
[ 12.811993] kernel BUG at net/core/dev.c:9937!
Fix this by properly crafted error path.
Fixes: b9663b7ca6ff ("net: stmmac: Enable SERDES power up/down sequence") Cc: Voon Weifeng <weifeng.voon@intel.com> Cc: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net/smc: add event-based framework for LLC msgs
These patches are the next step towards SMC-R link failover support. They add
a new framework to handle Link Layer Control (LLC) messages and adapt the
existing code to use the new framework.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The connection layer in af_smc.c is now using the new LLC flow
framework, which made the link state DELETING obsolete. Remove the state
and the respective helpers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The new SMC-R multiple link support will support a maximum of 3 links,
and one CONFIRM_RKEY LLC message can transport 3 rkeys of an rmb buffer.
There is no need for the LLC message type CONFIRM_RKEY_CONTINUE which is
needed when more than 3 rkeys per rmb buffer needs to be exchanged.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: adapt SMC remote DELETE_RKEY processing to use the LLC flow
Use the LLC flow framework for the processing of DELETE_RKEY messages
that were received from the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: adapt SMC remote CONFIRM_RKEY processing to use the LLC flow
Use the LLC flow framework for the processing of CONFIRM_RKEY messages
that were received from the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: new smc_rtoken_set functions for multiple link support
Introduce smc_rtoken_set() to set the rtoken for a new link to an
existing rmb whose rtoken is given, and smc_rtoken_set2() to set an
rtoken for a new link whose link_id is given.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: move the TEST_LINK response processing into event handler
Get rid of the extra function and move the two-liner for the TEST_LINK
response processing into the event handler function.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: multiple link support and LLC flow for smc_llc_do_delete_rkey
Adapt smc_llc_do_delete_rkey() to use the LLC flow and support multiple
links when deleting the rkeys for rmb buffers at the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: multiple link support and LLC flow for smc_llc_do_confirm_rkey
Adapt smc_llc_do_confirm_rkey() to use the LLC flow and support the
rkeys of multiple links when the CONFIRM_RKEY LLC message is build.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: adapt SMC client code to use the LLC flow
Change the code that processes the SMC client part of connection
establishment to use the LLC flow framework (CONFIRM_LINK request
messages).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: adapt SMC server code to use the LLC flow
Change the code that processes the SMC server part of connection
establishment to use the LLC flow framework (CONFIRM_LINK response
messages).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: add logic to evaluate CONFIRM_LINK messages to LLC layer
Introduce smc_llc_eval_conf_link() to evaluate the CONFIRM_LINK message
contents. This implements this logic at the LLC layer. The function will
be used by af_smc.c to process the received LLC layer messages.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a type field to the link group which reflects the current link group
redundancy state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_llc_enqueue() to enqueue LLC messages, and adapt
smc_llc_rx_handler() to enqueue all received LLC messages.
smc_llc_enqueue() also makes it possible to enqueue LLC messages from
local code.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The new framework allows to start specific types of LLC control flows,
protects active flows and makes it possible to wait for flows to finish
before starting a new flow.
This mechanism is used for the LLC control layer to model flows like
'add link' or 'delete link' which need to send/receive several LLC
messages and are not allowed to get interrupted by the wrong type of
messages.
'Add link' or 'Delete link' messages arriving in the middle of a flow
are delayed and processed when the current flow finished.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tang Bin [Thu, 30 Apr 2020 12:15:31 +0000 (20:15 +0800)]
net/faraday: Fix unnecessary check in ftmac100_probe()
The function ftmac100_probe() is only called with an openfirmware
platform device. Therefore there is no need to check that the passed
in device is NULL.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: mdio: add IPQ40xx MDIO support
This patch series provides support for the IPQ40xx built-in MDIO interface.
Included are driver, devicetree bindings for it and devicetree node.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Marko [Thu, 30 Apr 2020 09:07:07 +0000 (11:07 +0200)]
ARM: dts: qcom: ipq4019: add MDIO node
This patch adds the necessary MDIO interface node
to the Qualcomm IPQ4019 DTSI.
Built-in QCA8337N switch is managed using it,
and since we have a driver for it lets add it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Marko [Thu, 30 Apr 2020 09:07:06 +0000 (11:07 +0200)]
dt-bindings: add Qualcomm IPQ4019 MDIO bindings
This patch adds the binding document for the IPQ40xx MDIO driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Marko [Thu, 30 Apr 2020 09:07:05 +0000 (11:07 +0200)]
net: phy: mdio: add IPQ4019 MDIO driver
This patch adds the driver for the MDIO interface
inside of Qualcomm IPQ40xx series SoC-s.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
In our fast-path design, a WQE (Work Queue Element) must not cross the
page boundary. To enforce that, for WQEs consisting of more than one BB
(Basic Block), the driver checks the available contiguous space in the
WQ in advance, and if it's not enough, it pads it with NOPs.
This patch modifies the code that calculates the position of next WQE,
considering the padding, and prepares the WQE. This code is common for
all SQ types. In this patch it's reorganized in a way that makes the
usage pattern unified for all SQ types, and makes the implementations
self-contained and look almost the same, preparing the repeating code to
further attempts to deduplicate it.
One place is left as is: mlx5e_sq_xmit and mlx5e_fill_sq_frag_edge call
inside, because it is special in a way that it may also copy WQE's cseg
and eseg when reserving space. This will be eliminated in one of the
following patches, and this place will be converted to the new approach,
too.
Structs mlx5e_txqsq and mlx5e_xdpsq contain wqe_info arrays to store
supplementary information corresponding to WQEs in the queue. Struct
mlx5e_icosq also has such an array, but it's called differently -
ico_wqe. This patch renames it to unify with the other SQs.
In addition, rename the struct to emphasize its specific usage.
net/mlx5e: Fetch WQE: reuse code and enforce typing
There are multiple functions mlx5{e,i}_*_fetch_wqe that contain the same
code, that is repeated, because they operate on different SQ struct
types. mlx5e_sq_fetch_wqe also returns void *, instead of the concrete
WQE type.
This commit generalizes the fetch WQE operation by putting this code
into a single function. To simplify calls of the generic function in
concrete use cases, macros are provided that substitute the right WQE
size and cast the return type.
Before this patch, fetch_wqe used to calculate pi itself, but the value
was often known to the caller. This calculation is moved outside to
eliminate this unnecessary step and prepare for the fill_frag_edge
refactoring in the next patch.
projects / mirror_ubuntu-kernels.git / log