ARM: dts: imx6: edmqmx6: add SPI bus and flash

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpio

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6q-udoo: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add stdout-path property to i.MX boards

This adds the stdout-path property to various i.MX boards. Values
of the property have been taken from barebox, so they should be
correct. Also, the older linux,stdout-path property is converted
to stdout-path.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: Fix LVDS mapping for Ventana GW52xx

The GW52xx supports LVDS on channel 0. Remove the obsolete crtcs node and
add display timings for the HanStar HSD100PXN1 display.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: add LVDS backlight for Ventana

The GW54xx/GW53xx/GW52xx all support LVDS with a PWM controlled backlight.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: remove power-on gpio from pcie

This isn't compatible with the new binding and should be
handled via a proper regulator. It shouldn't be needed as
the driver has always ignored this property.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: update pcie to bring in line with new binding

The new bindings drops one clock, renames the others and
drops the old interrupt mapping.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx53-qsb-common: Add TVE support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Fix "reg" property for USBH2 PHY

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add CSI enable switch

This patch adds a GPIO fixed regulator which used on RDK to
enable CSI bus.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: Remove excess entries for PMIC

This patch removes excess "#address-cells" and "#size-cells" entries
for PMIC, since these entries is not used.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Disable PM pins for USB OTG

USB PWR and OC pins are used as GPIOs for different purposes,
so add "disable-over-current" property for OTG node to indicate this.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Fix active level for FEC reset

FEC reset GPIO is active low. Fix this typo.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Remove duplicate entries for USB PHY

"compatible", "#address-cells" and "#size-cells" for USB PHY are
already described in the SOM DTS. Remove these duplicate entries.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: ventana: Add HDMI support

Configure ddc and enable HDMI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: Add PCIe support

Add support for the PCI express bus available on MX6 SabreSDP.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-wandboard: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add keypad support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add NAND support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6q-gk802: Enable HDMI

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add USB OTG support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27: Place the usb phy nodes in the board dts files

It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.

Place the USB PHY nodes in the board dts files instead.

Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27: Use the correct usb clock gate

USB Host1, Host2 and OTG are gated via 'usb_ipg_gate' clock, so fix it in order
to avoid the following kernel oops:

usbcore: registered new interface driver usb-storage
10024000.usb supply vbus not found, using dummy regulator
Unhandled fault: external abort on non-linefetch (0x808) at 0xf4424184
Internal error: : 808 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc1-26325-g971f9fd-dirty #64
task: c7829aa0 ti: c7836000 task.ti: c7836000
PC is at ci_hdrc_probe+0x3a4/0x634
LR is at ci_hdrc_probe+0x100/0x634
pc : [<c036cc78>]    lr : [<c036c9d4>]    psr: 60000013
sp : c7837d48  ip : 00000001  fp : 00000000
r10: 00000000  r9 : 00000000  r8 : c791b6c0
r7 : c7945000  r6 : f4424000  r5 : c7945010  r4 : c794e010
r3 : f4424184  r2 : 00000000  r1 : 8c000004  r0 : 0c000004
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 0005317f  Table: a0004000  DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc78361c0)
Stack: (0xc7837d48 to 0xc7838000)

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Move PMIC IRQ GPIO into a separate pin group

The hardware is better described if we place the PMIC IRQ GPIO into its own
pingroup.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add PMIC support

imx27-pdk has a MC13783 PMIC connected to CSPI2 port.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Use predefined constants for clock definition

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add devicetree node for I2C1

This patch adds devicetree node and pinctrl group for I2C1.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Sort nodes by name

This patch sorts nodes by name and moves "iomux" configuration at
the bottom of file.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB OTG regulator node

This patch adds a regulator node and pinctrl group for USB OTG.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Use predefined constants for keys definition

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add missing pingroup for PMIC

This patch adds missing pin definition for PMIC IRQ GPIO.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Move "hog" pins into corresponded pin groups

Move "hog" pins into corresponded pin groups for eSDHC1, eSDHC2,
eCSPI1, gpio-keys, regulator-fixed and codec clock.
Additionally, this patch fixes GPIO active level definition for
USB regulator.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX51: Allow to define partitions onto NFC

This patch allow to define partitions onto NFC in user defined
devicetrees.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Enable DVI

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Enable UART1

This patch enables UART1 on the phyFLEX connector (i.MX6 uart3).

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: Add UART1 (uart3)

The pins labeled UART1 on the module connector are wired to i.MX6 uart3.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Add I2C devices

This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Add I2C2 and I2C3

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Set linux,stdout-path to UART4

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: PHY reset is active-low

Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: Add GPIO LEDs

This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add Phytec pbab01 with i.MX6 DualLite/Solo

The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the FEC pin configuration

Provide an entry for the FEC pin muxing.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the UART1 pin configuration

Provide an entry for the UART1 pin muxing.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Keep the dt nodes sorted

For better readability keep the dt nodes sorted.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM i.MX51: Add Digi ConnectCore devicetree

This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM
and basic support for the ConnectCore for i.MX51 JumpStart Kit.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX: Use single naming style for i.MX WEIM device

This patch converts all i.MX WEIM users to use single naming style
for devices.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: cpuimx51 Add touchscreen support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: cpuimx35 Add touchscreen support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd51 baseboard: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: add initial Colibri VF61 board support

Add initial Toradex Colibri VF61 board support. Ethernet, UART
and SDHC cards are working. Cache latencies need to be a bit
higher than vf610.dtsi suggests. Those values are validated
by running multiple memory tests.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

of: add vendor prefix for Toradex AG

Adds toradex to the list of DT vendor prefixes.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the memory range

imx27-pdk has 128 MB of DRAM. Pass the memory range in dt.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add display control signal definitions

This patch adds display control signal definitions.
These fields are not used in the driver yet, but will be used for
reference to indicate the polarity of the signals.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: use symbolic names from gpio.h

Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: fix phy reset gpio

Fix a copy & paste error: on duckbills the GPIO used for resetting
the ethernet phy differs from FSL's MX28EVK board.

Reported-by: Stefan Wahren <info@lategoodbye.de>
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28: include gpio.h to allow use of symbolic names

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: fix mmc settings

I2SE's duckbills are only equipped with a micro SD card slot and
thus only provide a 4-bit interface.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB OTG support

Tested by pinging from the host PC to the imx51-babbage via a g_ether
connection.

Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB Host1 support

Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx35-pdk: Add initial device tree support

Add support for UART, eSDHC and NAND.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Enables FTM PWM device.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Add PWM0's pinctrl node

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610: Add Freescale FTM PWM node.

This adds devicetree node for VF610, and there are 8 channels
supported.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX53: Add reset line to VPU device node

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX53: Enable CODA7541 VPU

This IP module is always present and has no external connections.
There is no reason to disable it in the device tree.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add USB Host1 support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add display support

This patch adds FB, Sharp-LQ035Q7 display (add-on module) and
corresponded pinctrl devicetree nodes to the Phytec PCM970 RDK.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add CAN support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add keypad support

Tested with evtest.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add audio support

mx25pdk has a sgtl5000 codec connected to the I2C1 port.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd35 baseboard: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX35: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd25 baseboard: Add USB support

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25.dtsi: Fix USB support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mx35: USB block requires only one clock

Like other imx SoCs only one USB clock is needed on mx35.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mx25: USB block requires only one clock

Like other imx SoCs only one USB clock is needed on mx25.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Add support for sdhc1

The kernel was not able to boot from SD card because sdhc support
was not present into the dts.

A new entry for sdhc1 was added for vf610-twr board based on the
compatible entry present on imx53.

After applying these changes, the kernel is able to boot successfully
from SD card.

Signed-off-by: Cosmin Stoica <cosminstefan.stoica@freescale.com>
Signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com>
Signed-off-by: Eddy Petrisor <eddy.petrisor@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add esdhc1 support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Provide an Ethernet PHY reset

GPIO4_8 is connected to the Ethernet PHY reset line, so populate the
'phy-reset-gpios' property accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Provide a regulator for Ethernet PHY

GPIO2_3 controls the power to the Ethernet PHY, so provide a regulator node
for this.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add FEC pins

Instead of relying on the bootloader for configuring the FEC pins, pass the
FEC pin configuration via device tree instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add UART1 pins

UART1 is the console port on mx25pdk board.

Add the pin configuration for UART1 port and also pass 'fsl,uart-has-rtscts'
to indicate that the port has RTS and CTS pins.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Sort the dt nodes

Keep the dt nodes sorted for better readability.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl-sabresd.dtsi: Add red led

Make the red gpio led available to the user.

This can be toggled with the sysfs for example, or used as a heartbeat or mmc
activity light by changing the trigger.

Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-som: Enable SSI1

This patch adds pin group for Synchronous Serial Interface 1 (SSI1)
for PCM-038 module and enables this interface. This change do nothing
at the current stage but helps to continue develop sound support.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-rdk: Add missing pinctrl definition for SPI CS1

This patch adds missing pinctrl definition for SPI chipselect 1.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx: Add alias for ethernet controller

Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: mbimxsd35: Add sound support.

Cc: Eric Bénard <eric@eukrea.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Linux 3.15-rc3

word-at-a-time: avoid undefined behaviour in zero_bytemask macro

The asm-generic, big-endian version of zero_bytemask creates a mask of
bytes preceding the first zero-byte by left shifting ~0ul based on the
position of the first zero byte.

Unfortunately, if the first (top) byte is zero, the output of
prep_zero_mask has only the top bit set, resulting in undefined C
behaviour as we shift left by an amount equal to the width of the type.
As it happens, GCC doesn't manage to spot this through the call to fls(),
but the issue remains if architectures choose to implement their shift
instructions differently.

An example would be arch/arm/ (AArch32), where LSL Rd, Rn, #32 results
in Rd == 0x0, whilst on arch/arm64 (AArch64) LSL Xd, Xn, #64 results in
Xd == Xn.

Rather than check explicitly for the problematic shift, this patch adds
an extra shift by 1, replacing fls with __fls. Since zero_bytemask is
never called with a zero argument (has_zero() is used to check the data
first), we don't need to worry about calling __fls(0), which is
undefined.

Cc: <stable@vger.kernel.org>
Cc: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'safe-dirty-tlb-flush'

This merges the patch to fix possible loss of dirty bit on munmap() or
madvice(DONTNEED).  If there are concurrent writers on other CPU's that
have the unmapped/unneeded page in their TLBs, their writes to the page
could possibly get lost if a third CPU raced with the TLB flush and did
a page_mkclean() before the page was fully written.

Admittedly, if you unmap() or madvice(DONTNEED) an area _while_ another
thread is still busy writing to it, you deserve all the lost writes you
could get.  But we kernel people hold ourselves to higher quality
standards than "crazy people deserve to lose", because, well, we've seen
people do all kinds of crazy things.

So let's get it right, just because we can, and we don't have to worry
about it.

* safe-dirty-tlb-flush:
  mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs

Pull btrfs fixes from Chris Mason.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: limit the path size in send to PATH_MAX
  Btrfs: correctly set profile flags on seqlock retry
  Btrfs: use correct key when repeating search for extent item
  Btrfs: fix inode caching vs tree log
  Btrfs: fix possible memory leaks in open_ctree()
  Btrfs: avoid triggering bug_on() when we fail to start inode caching task
  Btrfs: move btrfs_{set,clear}_and_info() to ctree.h
  btrfs: replace error code from btrfs_drop_extents
  btrfs: Change the hole range to a more accurate value.
  btrfs: fix use-after-free in mount_subvol()

Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm

Pull arm fixes from Russell King:
 "A number of fixes for the PJ4/iwmmxt changes which arm-soc forced me
  to take during the merge window.  This stuff should have been better
  tested and sorted out *before* the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8042/1: iwmmxt: allow to build iWMMXt on Marvell PJ4B
  ARM: 8041/1: pj4: fix cpu_is_pj4 check
  ARM: 8040/1: pj4: properly detect existence of iWMMXt coprocessor
  ARM: 8039/1: pj4: enable iWMMXt only if CONFIG_IWMMXT is set
  ARM: 8038/1: iwmmxt: explicitly check for supported architectures

Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:
 - compat renameat2 syscall wiring and __NR_compat_syscalls fix
 - TLB fix for transparent huge pages following switch to generic
   mmu_gather
 - spinlock initialisation for init_mm's context
 - move of_clk_init() earlier
 - Kconfig duplicate entry fix

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: init: Move of_clk_init to time_init
  arm64: initialize spinlock for init_mm's context
  arm64: debug: remove noisy, pointless warning
  arm64: mm: Add THP TLB entries to general mmu_gather
  arm64: add renameat2 compat syscall
  ARM64: Remove duplicated Kconfig entry for "kernel/power/Kconfig"
  arm64: __NR_compat_syscalls fix

Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq fixes from Thomas Gleixner:
 "A slighlty large fix for a subtle issue in the CPU hotplug code of
  certain ARM SoCs, where the not yet online cpu needs to setup the cpu
  local timer and needs to set the interrupt affinity to itself.
  Setting interrupt affinity to a not online cpu is prohibited and
  therefor the timer interrupt ends up on the wrong cpu, which leads to
  nasty complications.

  The SoC folks tried to hack around that in the SoC code in some more
  than nasty ways.  The proper solution is to have a way to enforce the
  affinity setting to a not online cpu.  The core patch to the genirq
  code provides that facility and the follow up patches make use of it
  in the GIC interrupt controller and the exynos timer driver.

  The change to the core code has no implications to existing users,
  except for the rename of the locked function and therefor the
  necessary fixup in mips/cavium.  Aside of that, no runtime impact is
  possible, as none of the existing interrupt chips implements anything
  which depends on the force argument of the irq_set_affinity()
  callback"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Exynos_mct: Register clock event after request_irq()
  clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup
  irqchip: Gic: Support forced affinity setting
  genirq: Allow forcing cpu affinity of interrupts

Merge tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
 "Here are a few tty/serial fixes for 3.15-rc3 that resolve a number of
  reported issues in the 8250 and samsung serial drivers, as well as a
  character loss fix for the tty core that was caused by the lock
  removal patches a release ago"

* tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial_core: fix uart PORT_UNKNOWN handling
  serial: samsung: Change barrier() to cpu_relax() in console output
  serial: samsung: don't check config for every character
  serial: samsung: Use the passed in "port", fixing kgdb w/ no console
  serial: 8250: Fix thread unsafe __dma_tx_complete function
  8250_core: Fix unwanted TX chars write
  tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc