If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull(). This requires a null-
terminator, and currently there's no guarantee that there is one.
(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator. It seems like it must
have worked by chance!)
Always add a null byte after the written data. Enlarge the buffer
to allow for this.
Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding. It
introduced regressions into both the dummy-hcd and net2280 drivers.
The problem in dummy-hcd was fixed by commit 7dbd8f4cabd9 ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.
This patch largely is a reversion of the relevant parts of f16443a034c7. It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.
Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off. Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks") Reported-by: D. Ziesche <dziesche@zes.com> Tested-by: D. Ziesche <dziesche@zes.com> CC: <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Reported-by: Junki Kato <junki.kato.xk@renesas.com> Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Junki Kato <junki.kato.xk@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Cc: <stable@vger.kernel.org> Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In case a client fails to connect in mei_cldev_enable(), the
caller won't call the mei_cldev_disable leaving the client
in a linked stated. Upon driver unload the client structure
will be freed in mei_cl_bus_dev_release(), leaving a stale pointer
on a fail_list. This will eventually end up in crash
during power down flow in mei_cl_set_disonnected().
Some of the ME clients are available only for BIOS operation and are
removed during hand off to an OS. However the removal is not instant.
A client may be visible on the client list when the mei driver requests
for enumeration, while the subsequent request for properties will be
answered with client not found error value. The default behavior
for an error is to perform client reset while this error is harmless and
the link reset should be prevented. This issue started to be visible due to
suspend/resume timing changes. Currently reported only on the Haswell
based system.
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
Fix a bug in the key delete code - the num_records range
from 0 to num_records-1.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reported-by: David Binderman <dcb314@hotmail.com> Cc: <stable@vger.kernel.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The SSIF driver was removing any client that came in through the
platform interface, but it should only remove clients that it
added. On a failure in the probe function, this could result
in the following oops when the driver is removed and the
client gets unregistered twice:
Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.
Here's the code in start_xmit where we check to see if the connection is
up:
if (ipoib_cm_get(neigh)) {
if (ipoib_cm_up(neigh)) {
ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
goto unref;
}
}
The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.
Commit 822fb18a82aba ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.
Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).
As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.
Fixes: 822fb18a82aba ("xen-netfront: wait xenbus state change when load module manually") Cc: <stable@vger.kernel.org> #4.18 Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
persistent_ram_vmap() returns the page start vaddr.
persistent_ram_iomap() supports non-page-aligned mapping.
persistent_ram_buffer_map() always adds offset-in-page to the vaddr
returned from these two functions, which causes incorrect mapping of
non-page-aligned persistent ram buffer.
By default ftrace_size is 4096 and max_ftrace_cnt is nr_cpu_ids. Without
this patch, the zone_sz in ramoops_init_przs() is 4096/nr_cpu_ids which
might not be page aligned. If the offset-in-page > 2048, the vaddr will be
in next page. If the next page is not mapped, it will cause kernel panic:
Signed-off-by: Bin Yang <bin.yang@intel.com>
[kees: add comments describing the mapping differences, updated commit log] Fixes: 24c3d2f342ed ("staging: android: persistent_ram: Make it possible to use memory outside of bootmem") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When AF_IB addresses are used during rdma_resolve_addr() a lock is not
held. A cma device can get removed while list traversal is in progress
which may lead to crash. ie
There is a call trace generated after commit 2d408c0d4574b01b9ed45e02516888bf925e11a9(
xen-netfront: fix queue name setting). There is no 'device/vif/xx-q0-tx' file found
under /proc/irq/xx/.
This patch only picks up device type and id as its name.
This patch fixes two typos related to unregistering algorithms supported by
SAHARAH 3. In sahara_register_algs the wrong algorithms are unregistered
in case of an error. In sahara_unregister_algs the wrong array is used to
determine the iteration count.
Signed-off-by: Michael Müller <michael@fds-team.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The mv_xor_v2 driver uses a tasklet, initialized during the probe()
routine. However, it forgets to cleanup the tasklet using
tasklet_kill() function during the remove() routine, which this patch
fixes. This prevents the tasklet from potentially running after the
module has been removed.
Fixes: 19a340b1a820 ("dmaengine: mv_xor_v2: new driver") Signed-off-by: Hanna Hawa <hannah@marvell.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.
There is a race window in device_shutdown(), which may cause
-1. parent device shut down before child or
-2. no shutdown on a new probing device.
For 1st, taking the following scenario:
device_shutdown new plugin device
list_del_init(parent_dev);
spin_unlock(list_lock);
device_add(child)
probe child
shutdown parent_dev
--> now child is on the tail of devices_kset
For 2nd, taking the following scenario:
device_shutdown new plugin device
device_add(dev)
device_lock(dev);
...
device_unlock(dev);
probe dev
--> now, the new occurred dev has no opportunity to shutdown
To fix this race issue, just prevent the new probing request. With this
logic, device_shutdown() is more similar to dpm_prepare().
Signed-off-by: Pingfan Liu <kernelfans@gmail.com> Reviewed-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The vgic_init function can race with kvm_arch_vcpu_create() which does
not hold kvm_lock() and we therefore have no synchronization primitives
to ensure we're doing the right thing.
As the user is trying to initialize or run the VM while at the same time
creating more VCPUs, we just have to refuse to initialize the VGIC in
this case rather than silently failing with a broken VCPU.
Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
After the subdriver's remove() routine has completed, the card's layer
mode is undetermined again. Reflect this in the layer2 field.
If qeth_dev_layer2_store() hits an error after remove() was called, the
card _always_ requires a setup(), even if the previous layer mode is
requested again.
But qeth_dev_layer2_store() bails out early if the requested layer mode
still matches the current one. So unless we reset the layer2 field,
re-probing the card back to its previous mode is currently not possible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
By updating q->used_buffers only _after_ do_QDIO() has completed, there
is a potential race against the buffer's TX completion. In the unlikely
case that the TX completion path wins, qeth_qdio_output_handler() would
decrement the counter before qeth_flush_buffers() even incremented it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.
Fixes: 9943230c8860 ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit f599c64fdf7d ("xen-netfront: Fix race between device setup and
open") changed the initialization order: xennet_create_queues() now
happens before we do register_netdev() so using netdev->name in
xennet_init_queue() is incorrect, we end up with the following in
/proc/interrupts:
and this looks ugly. Actually, using early netdev name (even when it's
already set) is also not ideal: nowadays we tend to rename eth devices
and queue name may end up not corresponding to the netdev name.
Use nodename from xenbus device for queue naming: this can't change in VM's
lifetime. Now /proc/interrupts looks like
After device is stopped we reset the rings by moving all free buffers
to positions [0, cnt - 2], and clear the position cnt - 1 in the ring.
We then proceed to clear the read/write pointers. This means that if
we try to reset the ring again the code will assume that the next to
fill buffer is at position 0 and swap it with cnt - 1. Since we
previously cleared position cnt - 1 it will lead to leaking the first
buffer and leaving ring in a bad state.
This scenario can only happen if FW communication fails, in which case
the ring will never be used again, so the fact it's in a bad state will
not be noticed. Buffer leak is the only problem. Don't try to move
buffers in the ring if the read/write pointers indicate the ring was
never used or have already been reset.
nfp_net_clear_config_and_disable() is now fully idempotent.
Found by code inspection, FW communication failures are very rare,
and reconfiguring a live device is not common either, so it's unlikely
anyone has ever noticed the leak.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Right now the only user of reset-imx7 is pci-imx6 and the
reset_control_assert and deassert calls on pciephy_reset don't toggle
the PCIEPHY_BTN and PCIEPHY_G_RST bits as expected. Fix this by writing
1 or 0 respectively.
The reference manual is not very clear regarding SRC_PCIEPHY_RCR but for
other registers like MIPIPHY and HSICPHY the bits are explicitly
documented as "1 means assert, 0 means deassert".
The values are still reversed for IMX7_RESET_PCIE_CTRL_APPS_EN.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
qe_muram_alloc return a unsigned long integer,which should not
compared with zero. check it using IS_ERR_VALUE() to fix this.
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.
Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.
This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.
For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.
* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
(AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
(AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)
Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.
Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)
Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.
This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.
To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.
This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and
should be == 0 here indicating timeout.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and should
be == 0 here indicating timeout which is the only error case so no additional
check needed here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The intention here is to consume and discard the remaining buffer
upon error. This works if there has not been a previous partial write.
If there has been, then total_len is no longer total number of bytes
to copy. total_len is always "bytes left to copy", so it should be
added to written bytes.
This code may not be exercised any more if partial writes will not be
hit, but this is a small bugfix before a larger change.
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the controller is going away, we need to unquiesce the IO queues so
that all pending request can fail gracefully before moving forward with
controller deletion. Do that before we destroy the IO queues so
blk_cleanup_queue won't block in freeze.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
For powerpc64, redundant entries in the callchain are filtered out by
determining the state of the return address and the stack frame using
DWARF debug information.
For making these filtering decisions we must analyze the debug
information for the location corresponding to the program counter value,
i.e. the first entry in the callchain, and not the LR value; otherwise,
perf may filter out either the second or the third entry in the
callchain incorrectly.
This can be observed on a powerpc64le system running Fedora 27 as shown
below.
Case 1 - Attaching a probe at inet_pton+0x8 (binary offset 0x15af28).
Return address is still in LR and a new stack frame is not yet
allocated. The LR value, i.e. the second entry, should not be
filtered out.
Case 2 - Attaching a probe at _int_malloc+0x180 (binary offset 0x9cf10).
Return address in still in LR and a new stack frame has already
been allocated but not used. The caller's caller, i.e. the third
entry, is invalid and should be filtered out and not the second
one.
For most of Exynos SoCs, Power Management Unit (PMU) address space is
mapped into global variable 'pmu_base_addr' very early when initializing
PMU interrupt controller. A lot of other machine code depends on it so
when doing iounmap() on this address, clear the global as well to avoid
usage of invalid value (pointing to unmapped memory region).
Properly mapped PMU address space is a requirement for all other machine
code so this fix is purely theoretical. Boot will fail immediately in
many other places after following this error path.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I discovered the problem when developing a frame buffer driver for the
PlayStation 2 (not yet merged), using the following video modes for the
PlayStation 3 in drivers/video/fbdev/ps3fb.c:
In ps3fb_probe, the mode_option module parameter is used with fb_find_mode
but it can only select the interlaced variant of 1920x1080 since the loop
matching the modes does not take the difference between interlaced and
progressive modes into account.
In short, without the patch, progressive 1920x1080 cannot be chosen as a
mode_option parameter since fb_find_mode (falsely) thinks interlace is a
perfect match.
Signed-off-by: Fredrik Noring <noring@nocrew.org> Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
[b.zolnierkie: updated patch description] Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When parsing the video modes from DT properties, make sure to zero out
memory before using it. This is important because not all fields in the mode
struct are explicitly initialized, even though they are used later on.
Fixes: 420a488278e86 ("video: fbdev: pxafb: initial devicetree conversion") Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
For powerpc64, perf will filter out the second entry in the callchain,
i.e. the LR value, if the return address of the function corresponding
to the probed location has already been saved on its caller's stack.
The state of the return address is determined using debug information.
At any point within a function, if the return address is already saved
somewhere, a DWARF expression can tell us about its location. If the
return address in still in LR only, no DWARF expression would exist.
Typically, the instructions in a function's prologue first copy the LR
value to R0 and then pushes R0 on to the stack. If LR has already been
copied to R0 but R0 is yet to be pushed to the stack, we can still get a
DWARF expression that says that the return address is in R0. This is
indicating that getting a DWARF expression for the return address does
not guarantee the fact that it has already been saved on the stack.
This can be observed on a powerpc64le system running Fedora 27 as shown
below.
[Switching to Thread 0x7ffff11ba700 (LWP 13749)]
0x00007ffff50839fb in raise () from /lib64/libc.so.6
(gdb)
#0 0x00007ffff50839fb in raise () from /lib64/libc.so.6
#1 0x00007ffff5085800 in abort () from /lib64/libc.so.6
#2 0x00007ffff507c0da in __assert_fail_base () from /lib64/libc.so.6
#3 0x00007ffff507c152 in __assert_fail () from /lib64/libc.so.6
#4 0x0000000000535373 in refcount_inc (r=0x7fffdc009be0)
at ...include/linux/refcount.h:109
#5 0x00000000005354f1 in comm_str__get (cs=0x7fffdc009bc0)
at util/comm.c:24
#6 0x00000000005356bd in __comm_str__findnew (str=0x7fffd000b260 ":2",
root=0xbed5c0 <comm_str_root>) at util/comm.c:72
#7 0x000000000053579e in comm_str__findnew (str=0x7fffd000b260 ":2",
root=0xbed5c0 <comm_str_root>) at util/comm.c:95
#8 0x000000000053582e in comm__new (str=0x7fffd000b260 ":2",
timestamp=0, exec=false) at util/comm.c:111
#9 0x00000000005363bc in thread__new (pid=2, tid=2) at util/thread.c:57
#10 0x0000000000523da0 in ____machine__findnew_thread (machine=0xbfde38,
threads=0xbfdf28, pid=2, tid=2, create=true) at util/machine.c:457
#11 0x0000000000523eb4 in __machine__findnew_thread (machine=0xbfde38,
...
The failing assertion is this one:
REFCOUNT_WARN(!refcount_inc_not_zero(r), ...
The problem is that we keep global comm_str_root list, which
is accessed by multiple threads during the 'perf top' startup
and following 2 paths can race:
Because thread 2 first decrements the refcnt and only after then it removes the
struct comm_str from the list, the thread 1 can find this object on the list
with refcnt equls to 0 and hit the assert.
This patch fixes the thread 1 __comm_str__findnew path, by ignoring objects
that already dropped the refcnt to 0. For the rest of the objects we take the
refcnt before comparing its name and release it afterwards with comm_str__put,
which can also release the object completely.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Lukasz Odzioba <lukasz.odzioba@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Cc: kernel-team@lge.com Link: http://lkml.kernel.org/r/20180720101740.GA27176@krava Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Stephan reported, that pipe mode does not carry the group information
and thus the piped report won't display the grouped output for following
command:
# perf record -e '{cycles,instructions,branches}' -a sleep 4 | perf report
It has no idea about the group setup, so it will display events
separately:
Before this patch, you could get into situations like this:
1. Process 1 searches for X free blocks, finds them, makes a reservation
2. Process 2 searches for free blocks in the same rgrp, but now the
bitmap is full because process 1's reservation is skipped over.
So it marks the bitmap as GBF_FULL.
3. Process 1 tries to allocate blocks from its own reservation, but
since the GBF_FULL bit is set, it skips over the rgrp and searches
elsewhere, thus not using its own reservation.
This patch adds an additional check to allow processes to use their
own reservations.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Perf test 40 for example has several subtests numbered 1-4 when
displaying the start of the subtest. When the subtest results
are displayed the subtests are numbered 0-3.
Use this command to generate trace output:
[root@s35lp76 perf]# ./perf test -Fv 40 2>/tmp/bpf1
Fix this by adjusting the subtest number when show the
subtest result.
The external clock frequency was set to 23.88MHz by mistake
because of a platform which cannot get closer to 24MHz.
The supported by the driver external clock is 24MHz so
set it correctly and also fix the values of the pixel
clock and link clock.
However allow 1% tolerance to the external clock as this
difference is small enough to be insignificant.
Fix 2 printk format warnings (this driver is currently only used by
arch/sh/) by using "%pap" instead of "%lx".
Fixes these build warnings:
../drivers/mtd/maps/solutionengine.c: In function 'init_soleng_maps':
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:54: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:72: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Boris Brezillon <boris.brezillon@bootlin.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: linux-mtd@lists.infradead.org Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: linux-sh@vger.kernel.org Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix to return a negative error code from the ipoib_neigh_hash_init()
error handling case instead of 0, as done elsewhere in this function.
Fixes: 515ed4f3aab4 ("IB/IPoIB: Separate control and data related initializations") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to "Annex A16: RDMA over Converged Ethernet (RoCE)":
A16.4.3 MANAGEMENT INTERFACES
As defined in the base specification, a special Queue Pair, QP0 is defined
solely for communication between subnet manager(s) and subnet management
agents. Since such an IB-defined subnet management architecture is outside
the scope of this annex, it follows that there is also no requirement that
a port which conforms to this annex be associated with a QP0. Thus, for
end nodes designed to conform to this annex, the concept of QP0 is
undefined and unused for any port connected to an Ethernet network.
CA16-8: A packet arriving at a RoCE port containing a BTH with the
destination QP field set to QP0 shall be silently dropped.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Moni Shoua <monis@mellanox.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The vb2_core_qbuf() function didn't check if q->error was set. It is
checked in __buf_prepare(), but that function isn't called if the buffer
was already prepared before with VIDIOC_PREPARE_BUF.
So check it at the start of vb2_core_qbuf() as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In pl330_update() when checking if a channel has been aborted, the
channel's lock is not taken, only the overall pl330_dmac lock. But in
pl330_terminate_all() the aborted flag (req_running==-1) is set under
the channel lock and not the pl330_dmac lock.
With threaded interrupts, this leads to a potential race:
If Make gets a fatal signal while a shell is executing, it may delete
the target file that the recipe was supposed to update. This is needed
to make sure that it is remade from scratch when Make is next run; if
Make is interrupted after the recipe has begun to write the target file,
it results in an incomplete file whose time stamp is newer than that
of the prerequisites files. Make automatically deletes the incomplete
file on interrupt unless the target is marked .PRECIOUS.
The situation is just the same as when the shell fails for some reasons.
Usually when a recipe line fails, if it has changed the target file at
all, the file is corrupted, or at least it is not completely updated.
Yet the file’s time stamp says that it is now up to date, so the next
time Make runs, it will not try to update that file.
However, Make does not cater to delete the incomplete target file in
this case. We need to add .DELETE_ON_ERROR somewhere in the Makefile
to request it.
scripts/Kbuild.include seems a suitable place to add it because it is
included from almost all sub-makes.
Please note .DELETE_ON_ERROR is not effective for phony targets.
The external module building should never ever touch the kernel tree.
The following recipe fails if include/generated/autoconf.h is missing.
However, include/config/auto.conf is not deleted since it is a phony
target.
PHONY += include/config/auto.conf
include/config/auto.conf:
$(Q)test -e include/generated/autoconf.h -a -e $@ || ( \
echo >&2; \
echo >&2 " ERROR: Kernel configuration is invalid."; \
echo >&2 " include/generated/autoconf.h or $@ are missing.";\
echo >&2 " Run 'make oldconfig && make prepare' on kernel src to fix it."; \
echo >&2 ; \
/bin/false)
Fixed factor clock has two initializations at of_clk_init() time
and during platform driver probe. Before of_clk_init() call,
node is marked as populated and so its probe never gets called.
During of_clk_init() fixed factor clock registration may fail if
any of its parent clock is not registered. In this case, it doesn't
get chance to retry registration from probe. Clear OF_POPULATED
flag if fixed factor clock registration fails so that clock
registration is attempted again from probe.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Patch "clk: core: Copy connection id" made it so that the connector id
'con_id' is kstrdup_const()ed to cater to drivers that pass non-constant
connection ids. The patch added the corresponding kfree_const to
__clk_free_clk(), but struct clk's can be freed also via __clk_put().
Add the kfree_const call to __clk_put() and add comments to both
functions to remind that the logic in them should be kept in sync.
Fixes: 253160a8ad06 ("clk: core: Copy connection id") Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 787b4271a6a0 ("clk: imx: add imx6ul clk tree support") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
To speed up the common case of appending to a file,
gfs2_write_alloc_required presumes that writing beyond the end of a file
will always require additional blocks to be allocated. This assumption
is incorrect for preallocates files, but there are no negative
consequences as long as *some* space is still left on the filesystem.
One special file that always has some space preallocated beyond the end
of the file is the rindex: when growing a filesystem, gfs2_grow adds one
or more new resource groups and appends records describing those
resource groups to the rindex; the preallocated space ensures that this
is always possible.
However, when a filesystem is completely full, gfs2_write_alloc_required
will indicate that an additional allocation is required, and appending
the next record to the rindex will fail even though space for that
record has already been preallocated. To fix that, skip the incorrect
optimization in gfs2_write_alloc_required, but for the rindex only.
Other writes to preallocated space beyond the end of the file are still
allowed to fail on completely full filesystems.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
AU0828_DEVICE() macro in quirks-table.h uses USB_DEVICE_VENDOR_SPEC()
for expanding idVendor and idProduct fields. However, the latter
macro adds also match_flags and bInterfaceClass, which are different
from the values AU0828_DEVICE() macro sets after that.
For fixing them, just expand idVendor and idProduct fields manually in
AU0828_DEVICE().
This fixes sparse warnings like:
sound/usb/quirks-table.h:2892:1: warning: Initializer entry defined twice
When run on a 64-bit system in selftest, the v7s driver may obtain page
table with physical addresses larger than 32-bit. Level-2 tables are 1KB
and are are allocated with slab, which doesn't accept the GFP_DMA32
flag. Currently map() truncates the address written in the PTE, causing
iova_to_phys() or unmap() to access invalid memory. Kasan reports it as
a use-after-free. To avoid any nasty surprise, test if the physical
address fits in a PTE before returning a new table. 32-bit systems,
which are the main users of this page table format, shouldn't see any
difference.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to the documentation in msg_zerocopy.rst, the SO_ZEROCOPY
flag was introduced because send(2) ignores unknown message flags and
any legacy application which was accidentally passing the equivalent of
MSG_ZEROCOPY earlier should not see any new behaviour.
Before commit f214f915e7db ("tcp: enable MSG_ZEROCOPY"), a send(2) call
which passed the equivalent of MSG_ZEROCOPY without setting SO_ZEROCOPY
would succeed. However, after that commit, it fails with -ENOBUFS. So
it appears that the SO_ZEROCOPY flag fails to fulfill its intended
purpose. Fix it.
Fixes: f214f915e7db ("tcp: enable MSG_ZEROCOPY") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If erspan tunnel hasn't been established, we'd better send icmp port
unreachable message after receive erspan packets.
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When processing icmp unreachable message for erspan tunnel, tunnel id
should be erspan_net_id instead of ipgre_net_id.
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
tls_sw_sendmsg() allocates plaintext and encrypted SG entries using
function sk_alloc_sg(). In case the number of SG entries hit
MAX_SKB_FRAGS, sk_alloc_sg() returns -ENOSPC and sets the variable for
current SG index to '0'. This leads to calling of function
tls_push_record() with 'sg_encrypted_num_elem = 0' and later causes
kernel crash. To fix this, set the number of SG elements to the number
of elements in plaintext/encrypted SG arrays in case sk_alloc_sg()
returns -ENOSPC.
Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware and software flows") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a rds sock is bound, it is inserted into the bind_hash_table
which is protected by RCU. But when releasing rds sock, after it
is removed from this hash table, it is freed immediately without
respecting RCU grace period. This could cause some use-after-free
as reported by syzbot.
Mark the rds sock with SOCK_RCU_FREE before inserting it into the
bind_hash_table, so that it would be always freed after a RCU grace
period.
The other problem is in rds_find_bound(), the rds sock could be
freed in between rhashtable_lookup_fast() and rds_sock_addref(),
so we need to extend RCU read lock protection in rds_find_bound()
to close this race condition.
Reported-and-tested-by: syzbot+8967084bcac563795dc6@syzkaller.appspotmail.com Reported-by: syzbot+93a5839deb355537440f@syzkaller.appspotmail.com Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com> Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com> Cc: rds-devel@oss.oracle.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oarcle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf676 ("net: qualcomm: new Ethernet over SPI driver for QCA700") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reviewed-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If FI_EXTRA_ATTR is set in inode by fuzzing, inode.i_addr[0] will be
parsed as inode.i_extra_isize, then in __recover_inline_status, inline
data address will beyond boundary of page, result in accessing invalid
memory.
So in this condition, during reading inode page, let's do sanity check
with EXTRA_ATTR feature of fs and extra_attr bit of inode, if they're
inconsistent, deny to load this inode.
- Overview
Out-of-bound access in f2fs_iget() when mounting a corrupted f2fs image
- Reproduce
The following message will be got in KASAN build of 4.18 upstream kernel.
[ 819.392227] ==================================================================
[ 819.393901] BUG: KASAN: slab-out-of-bounds in f2fs_iget+0x736/0x1530
[ 819.395329] Read of size 4 at addr ffff8801f099c968 by task mount/1292
My Chromebook Plus (kevin) is spitting the following at boot time:
(NULL device *): hwmon: 'sbs-9-000b' is not a valid name attribute, please fix
Clearly, __hwmon_device_register is unhappy about the property name.
Some investigation reveals that thermal_add_hwmon_sysfs doesn't
sanitize the name of the attribute.
In order to keep it quiet, let's replace '-' with '_' in hwmon->type
This is consistent with what iio-hwmon does since b92fe9e3379c8.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The pxa3xx driver uses the pinctrl-single driver since a while which
does not implement a .gpio_set_direction() callback. The pinmux core
will simply return 0 in this case, and the pxa3xx gpio driver hence
believes the pinctrl driver did its job and returns as well.
This effectively makes pxa_gpio_direction_{input,output} no-ops.
To fix this, do not call into the pinctrl subsystem for the PXA3xx
platform for now. We can revert this once the pinctrl-single driver
learned to support setting pin directions.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
dax_pmem_percpu_exit() waits for dax_pmem_percpu_release() to invoke the
dax_pmem->cmp completion. Unfortunately this approach to cleaning up
the percpu_ref only works after devm_memremap_pages() was successful.
If devm_add_action_or_reset() or devm_memremap_pages() fails,
dax_pmem_percpu_release() is not invoked. Therefore
dax_pmem_percpu_exit() hangs waiting for the completion:
rc = devm_add_action_or_reset(dev, dax_pmem_percpu_exit,
&dax_pmem->ref);
if (rc)
return rc;
For the case when sbi->segs_per_sec > 1 with lfs mode, take
section:segment = 5 for example, if the section prefree_map is
...previous section | current section (1 1 0 1 1) | next section...,
then the start = x, end = x + 1, after start = start_segno +
sbi->segs_per_sec, start = x + 5, then it will skip x + 3 and x + 4, but
their bitmap is still set, which will cause duplicated
f2fs_issue_discard of this same section in the next write_checkpoint:
round 1: section bitmap : 1 1 1 1 1, all valid, prefree_map: 0 0 0 0 0
then rm data block NO.2, block NO.2 becomes invalid, prefree_map: 0 0 1 0 0
write_checkpoint: section bitmap: 1 1 0 1 1, prefree_map: 0 0 0 0 0,
prefree of NO.2 is cleared, and no discard issued
round 2: rm data block NO.0, NO.1, NO.3, NO.4
all invalid, but prefree bit of NO.2 is set and cleared in round 1, then
prefree_map: 1 1 0 1 1
write_checkpoint: section bitmap: 0 0 0 0 0, prefree_map: 0 0 0 1 1, no
valid blocks of this section, so discard issued, but this time prefree
bit of NO.3 and NO.4 is skipped due to start = start_segno + sbi->segs_per_sec;
round 3:
write_checkpoint: section bitmap: 0 0 0 0 0, prefree_map: 0 0 0 1 1 ->
0 0 0 0 0, no valid blocks of this section, so discard issued,
this time prefree bit of NO.3 and NO.4 is cleared, but the discard of
this section is sent again...
To fix this problem, we can align the start and end value to section
boundary for fstrim and real-time discard operation, and decide to issue
discard only when the whole section is invalid, which can issue discard
aligned to section size as much as possible and avoid redundant discard.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com> Signed-off-by: Chao Yu <yuchao0@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If we attempt to request more blocks than we have room for, we try to
instead request as much as we can, however, alloc_valid_block_count
is not decremented to match the new value, allowing it to drift higher
until the next checkpoint. This always decrements it when the requested
amount cannot be fulfilled.
Signed-off-by: Daniel Rosenberg <drosen@google.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The periphery can't be accessed before we set the
INIT_DONE bit which initializes the device.
A previous patch added a reconfiguration of the MSI-X
tables upon resume, but at that point in the flow,
INIT_DONE wasn't set. Since the reconfiguration of the
MSI-X tables require periphery access, it failed.
The difference between WoWLAN and without WoWLAN is that
in WoWLAN, iwl_trans_pcie_d3_suspend clears the INIT_DONE
without clearing the STATUS_DEVICE_ENABLED bit in the
software status. Because of that, the resume code thinks
that the device is enabled, but the INIT_DONE bit has been
cleared.
To fix this, don't reconfigure the MSI-X tables in case
WoWLAN is enabled. It will be done in
iwl_trans_pcie_d3_resume anyway.
During normal IO, FW can return IO with 'port unavailble' status. Driver
would send a LOGO to remote port for session resync. On an off chance, a
PLOGI could arrive before sending the LOGO. This patch will skip sendiing
LOGO if a PLOGI just came in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
- Return valid error codes from ppc4xx_setup_pcieh_hw(), have it clean
up after itself, and only access hardware after all possible error
conditions have been handled.
- Use devm_kzalloc() instead of kzalloc() in ppc4xx_msi_probe()
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log