Andy Walls [Sat, 30 Jan 2010 18:50:51 +0000 (15:50 -0300)]
V4L/DVB: cx18: Fix memory leak in cx18-alsa starting of PCM captures
The cx18_open_id is normally dynamically allocated and stored in the
filp->private_data for v4l2 file operations. The cx18-alsa routines should
not dynamically allocate a cx18_open_id because they never store it anywhere
and never free it. This change fixes that and plugs a memory leak.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 30 Jan 2010 18:28:22 +0000 (15:28 -0300)]
V4L/DVB: cx18: Add missing serialization locking to cx18-alsa
File operations that manipulate the state of the encoder, or video or audio
subdevices or some of the stream flags need to be serialized. Add the
serilization locks to cx18-alsa in a manner consistent with the locking for
the v4l2 file operations.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Tue, 26 Jan 2010 19:46:58 +0000 (16:46 -0300)]
V4L/DVB: dvb/bt8xx: Clean-up init and exit functions
The init and exit functions are needlessly complex. Remove the bloat:
* Drop irrelevant/outdated comments.
* Remove useless bt878_pci_driver_registered global variable.
Arnaud Patard [Mon, 25 Jan 2010 15:02:31 +0000 (12:02 -0300)]
V4L/DVB: Fix VIDIOC_QBUF compat ioctl32
When using VIDIOC_QBUF with memory type set to V4L2_MEMORY_MMAP, the
v4l2_buffer buffer gets unmodified on drivers like uvc (well, only
bytesused field is modified). Then some apps like gstreamer are reusing
the same buffer later to call munmap (eg passing the buffer "length"
field as 2nd parameter of munmap).
It's working fine on full 32bits but on 32bits systems with 64bit
kernel, the get_v4l2_buffer32() doesn't copy length/m.offset values and
then copy garbage to userspace in put_v4l2_buffer32().
This has for consequence things like that in the libv4l2 logs:
Márton Németh [Sat, 23 Jan 2010 06:58:20 +0000 (03:58 -0300)]
V4L/DVB: zoran: match parameter signedness of g_input_status
The second parameter of g_input_status operation in <media/v4l2-subdev.h>
is unsigned so also call it with unsigned paramter.
This will remove the following sparse warning (see "make C=1"):
* incorrect type in argument 2 (different signedness)
expected unsigned int [usertype] *status
got int *<noident>
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:03:31 +0000 (16:03 -0300)]
V4L/DVB: firedtv: reduce memset()s
Before each FCP transdaction, the entire 512 bytes of the FCP frame were
cleared, then values filled in.
Clear only the bytes between filled-in bytes and end of the
- request frame, or
- response frame if data from a larger response will be needed, or
- whole frame if data from a variable length response will be taken.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:03:03 +0000 (16:03 -0300)]
V4L/DVB: firedtv: remove check for interrupting signal
FCP transactions as well as CMP transactions were serialized with
mutex_lock_interruptible. It is extremely unlikly though that a signal
will arrive while a concurrent process holds the mutex. And even if one
does, the duration of a transaction is reasonably short (1.2 seconds if
all retries time out, usually much shorter).
Hence simplify the code to plain mutex_lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:02:01 +0000 (16:02 -0300)]
V4L/DVB: firedtv: do not DMA-map stack addresses
This is a portability fix and reduces stack usage.
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firedtv (payload of write requests in avc_write and
of lock requests in cmp_lock) to slab-allocated memory.
We use the 512 bytes sized FCP frame buffer in struct firedtv for this
purpose. Previously it held only incoming FCP responses, now it holds
pending FCP requests and is then overwriten by an FCP response from the
tuner subunit. Ditto for CMP lock requests and responses. Accesses to
the payload buffer are serialized by fdtv->avc_mutex.
As a welcome side effect, stack usage of the AV/C transaction functions
is reduced by 512 bytes.
Alas, avc_register_remote_control() is a special case: It previously
did not wait for a response. To fit better in with the other FCP
transactions, let it wait for an interim response.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
WARNING: drivers/media/video/cx18/cx18-alsa.o(.text+0x4de): Section
mismatch in reference from the function cx18_alsa_load() to the function
.init.text:snd_cx18_init()
The function cx18_alsa_load() references
the function __init snd_cx18_init().
This is often because cx18_alsa_load lacks a __init
annotation or the annotation of snd_cx18_init is wrong.
WARNING: drivers/media/video/cx18/built-in.o(.text+0x1c022): Section
mismatch in reference from the function cx18_alsa_load() to the function
.init.text:snd_cx18_init()
The function cx18_alsa_load() references
the function __init snd_cx18_init().
This is often because cx18_alsa_load lacks a __init
annotation or the annotation of snd_cx18_init is wrong.
WARNING: drivers/media/video/built-in.o(.text+0x28cc56): Section
mismatch in reference from the function cx18_alsa_load() to the function
.init.text:snd_cx18_init()
The function cx18_alsa_load() references
the function __init snd_cx18_init().
This is often because cx18_alsa_load lacks a __init
annotation or the annotation of snd_cx18_init is wrong.
WARNING: drivers/media/built-in.o(.text+0x2d2432): Section mismatch in
reference from the function cx18_alsa_load() to the function
.init.text:snd_cx18_init()
The function cx18_alsa_load() references
the function __init snd_cx18_init().
This is often because cx18_alsa_load lacks a __init
annotation or the annotation of snd_cx18_init is wrong.
Antonio Ospite [Sun, 17 Jan 2010 06:42:14 +0000 (03:42 -0300)]
V4L/DVB: gspca - ov534: Fix end of frame handling
Fix a regression, introduced in the driver split, which made
the ov534 driver unusable.
Plus, the debug message should reflect that we discard also packets
beyond the expected frame size.
Hans de Goede [Wed, 13 Jan 2010 10:12:28 +0000 (07:12 -0300)]
V4L/DVB: gspca - zc3xx: Change the resolutions of some sensors
The sensors adcm2700, mc501cb and ov7620 cannot have the full height
permitted by the zc3xx bridges. This change removes 8 pixels at the
bottom of the images.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 16 Jan 2010 16:41:43 +0000 (13:41 -0300)]
V4L/DVB: stv0900: make more local functions static
Some functions are only used locally so mark them static.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'extract_mask_pos' was not declared. Should it be static?
* symbol 'stv0900_initialize' was not declared. Should it be static?
* symbol 'stv0900_get_mclk_freq' was not declared. Should it be static?
* symbol 'stv0900_set_mclk' was not declared. Should it be static?
* symbol 'stv0900_get_err_count' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 16 Jan 2010 16:35:36 +0000 (13:35 -0300)]
V4L/DVB: stv0900: make local functions static
The functions stv0900_sw_algo() and stv0900_set_dvbs1_track_car_loop() are only used
locally so mark them static.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'stv0900_sw_algo' was not declared. Should it be static?
* symbol 'stv0900_set_dvbs1_track_car_loop' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 16 Jan 2010 16:21:59 +0000 (13:21 -0300)]
V4L/DVB: cx231xx: cleanup dvb_attach() return value handling
Remove the following sparse error (see "make C=1"):
* error: incompatible types for operation (<)
left side has type struct dvb_frontend *
right side has type int
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: vpfe-capture: converting dm644x ccdc driver to a platform driver
1) clocks are configured using generic clock names
2) converting the driver to a platform driver
3) cleanup - consolidate all static variables inside a structure, ccdc_cfg
The ccdc driver now uses generic names for clocks - master and slave. On individual platforms
these clocks will inherit from the platform specific clock. This will allow re-use of
the driver for the same IP across different SoCs.
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com> Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com> Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: vpfe-capture - converting dm355 ccdc driver to a platform driver
1) clocks are configured using generic clock names;
2) converts the driver to a platform driver;
3) cleanup - consolidate all static variables inside a structure, ccdc_cfg;
The ccdc now uses a generic name for clocks. "master" and "slave". On individual platforms
these clocks will inherit from the platform specific clock. This will allow re-use of
the driver for the same IP across different SoCs.
Updated based on Kevin's comments on clock configuration and error code (v3, v4).
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com> Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com> Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pete Eberlein [Wed, 13 Jan 2010 22:15:48 +0000 (19:15 -0300)]
V4L/DVB: s2250: Fix write_reg i2c address
The kernel i2c model uses right-aligned 7-bit i2c addresses, but the
2250 firmware uses an 8-bit address in the usb vendor request. A
previous patch by Jean Delvare shifted the i2c addresses 1 bit to the
right, and this patch fixes the write_reg function to shift it back
before sending the vendor request.
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Pete Eberlein <pete@sensoray.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the cx18_alsa_announce_pcm_data() function further up in the file, since
apparently "make checkpatch" has never heard of a forward declaration. Note
that despite the hg diff showing everything else as having been deleted/added,
in reality it was only that one function that got moved (and the forward
declaration was removed from the top of the file).
Fix codingstyle issues, and make the minimum version for cx18-alsa required
to be 2.6.17, so that we don't need all the #ifdefs related to the changes
to ALSA structures.
V4L/DVB: cx18: rework cx18-alsa module loading to support automatic loading
Restructure the way the module gets loaded so that it gets loaded automatically
when cx18 is loaded, and make it work properly if there are multiple cards
present (since the old code would only take one opportunity to connect to cx18
instances when the module first loaded).
V4L/DVB: cx18: make it so cx18-alsa-main.c compiles
Fix some basic compilation issues with Andy's original code. In particular,
temporarily #ifdef out the mixer code, add some additional exception handling,
fix a couple of typos, and add a copyright line.
Andy Walls [Mon, 18 Jan 2010 00:12:24 +0000 (21:12 -0300)]
V4L/DVB: ivtv: Adjust msleep() delays used to prevent tinny audio and PCI bus hang
Martin Dauskardt <martin.dauskardt@gmx.de> has done extensive testing on what
values can be used and and concluded that only 300 ms total is required to
avoid bad video effects such as occasional black screen and short sync
disturbances. Furthermore he determined how this 300 ms was split between
the two msleep()s did matter very much, so he suggested 150ms/150ms as one
acceptable alternative that is implemented here.
Many thanks go to Martin.
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de> Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ian Armstrong [Tue, 22 Dec 2009 01:59:26 +0000 (22:59 -0300)]
V4L/DVB: ivtv: Fix race condition for queued udma transfers
There are several DMA related interrupts which wake up the dma_waitq. The udma
routines use this queue while they wait for their transfer to complete. When
woken, the udma routine will check the IVTV_F_I_UDMA_PENDING & IVTV_F_I_UDMA
flags to see if the transfer is still queued or has finished. However, a small
window exists between the IVTV_F_I_UDMA_PENDING flag being cleared and the
IVTV_F_I_UDMA flag being set. Given that the completion of an unrelated DMA
transfer may wake up the udma routine, it's possible for this check to fail
and the udma routine will start unmapping pages when the transfer has only
just started. The result of this is unpredictable.
This fix simply delays the clearing of the IVTV_F_I_UDMA_PENDING flag until
after IVTV_F_I_UDMA has been set.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Abylay Ospan [Fri, 22 Jan 2010 19:01:44 +0000 (16:01 -0300)]
V4L/DVB: 22-kHz set_tone fix for NetUP Dual DVB-S2-CI card. 22kHz logic controlled by demod
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Hans de Goede [Thu, 14 Jan 2010 13:00:31 +0000 (10:00 -0300)]
V4L/DVB (14005): media/video Kconfig: Mark gspca superceeded drivers as deprecated
We have some duplicate functionality between the zc0301 and gspca-zc3xx,
the sn9c102 and gspca-sonixb + gspca-sonix, and et61x251 and gscpa-etoms
drivers.
The non gspca versions of these drivers not only show a lot of code
duplicty (amongsth each other), as they all copy the same generic usb
webcam code instead of using some sort of framework. They also have not
seen any updates for more then 2 years, where as the gspca drivers are
actively maintained.
So it is time for the non gspca versions of these drivers to go away,
marking them as deprecated is the first step in this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 10 Jan 2010 22:34:57 +0000 (19:34 -0300)]
V4L/DVB (14002): gspca_sonixb / sn9c102: Make gspca handle 0c45:6007
When both the gspca_sonixb and the sn9c102 driver are enabled, make the
gspca_sonixb driver handle cams with usb-id of 0c45:6007. The sn9c102 driver
is being phased out and gspca driver has been successfully tested
with an 0c45:6007 camara.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 10 Jan 2010 22:31:34 +0000 (19:31 -0300)]
V4L/DVB (14001): gscpa_sonixb: Differentiate between tas5110c and tas5110d and fix d hstart
Our hstart value was wrong for tas5110d sensor using sonixb cams, this
patch fixes this. Many thanks to Paulus (laudaka) for donating me a camera
with such a sensor IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 7 Jan 2010 18:42:35 +0000 (15:42 -0300)]
V4L/DVB (13997): gspca_ov519: differentiate ov7620 and ov7620ae and fix 640x480 on the 7620
Michael Deegan <michael@ucc.gu.uwa.edu.au>, has reported issues with
using 640x480 mode on his ov518+ webcam. The fix for this breaks things
on my ov518+ cam (Trust 320 Sp@cecam), this patch thus adds differentiation
in the driver between the OV7620 sensor his cam has and the OV7620AE sensor
my cam has, and then only changes the init sequence for the ov518+ +
OV7620 combo which was not working for Michael.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 7 Jan 2010 18:31:48 +0000 (15:31 -0300)]
V4L/DVB (13996): gspca_stv0680: Fix streaming on vga cameras
Streaming of VGA stv0680 based cams (instead of CIF ones) failed, because
we were using the wrong control pipe for certain commands, this patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 7 Jan 2010 15:06:00 +0000 (12:06 -0300)]
V4L/DVB (13995): gspca_ov519: mark led on eyetoy II as inverted
Mark led on eyetoy II as inverted, I have the feeling the led needs to
be inverted for all 519 based cams (iow we got the set led code wrong), but
lets just deal with this one cam at a time to avoid breaking currently
working cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 7 Jan 2010 15:04:04 +0000 (12:04 -0300)]
V4L/DVB (13994): gscpa_stv0680: Fix camera initialization on hotplug
stv0680 cameras currently only work when already plugged in when the system
boots (or when manually re-loading the driver after boot). This patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Theodore Kilgore [Fri, 25 Dec 2009 08:15:10 +0000 (05:15 -0300)]
V4L/DVB (13991): gspca_mr973010a: Fix cif type 1 cameras not streaming on UHCI controllers
If you read the mail to Oliver Neukum on the linux-usb list, then you know
that I found a cure for the mysterious problem that the MR97310a CIF "type
1" cameras have been freezing up and refusing to stream if hooked up to a
machine with a UHCI controller.
Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you
have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or
such. It un-blocks whatever was previously stopping the CIF type 1 cameras
from working on the UHCI-based machines.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add parameters adc1_range, adc2_range and tuner_bbgain to the config struct.
Defaults: adc1_range = adc2_range = 2Vpp, tuner_bbgain = 10db
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Sun, 10 Jan 2010 18:39:45 +0000 (15:39 -0300)]
V4L/DVB (13987): [STV090x] Quit processing if the tuner did not lock
Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Sun, 10 Jan 2010 18:38:38 +0000 (15:38 -0300)]
V4L/DVB (13986): [STV090x] Disable I2C gate on error
The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:24:56 +0000 (19:24 -0300)]
V4L/DVB (13985): [STV090x] reset mclk and dev_ver of internal structure after allocating
When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:24:32 +0000 (19:24 -0300)]
V4L/DVB (13984): [BUDGET] Use a tuner clock output divider of 2 for TT S2-1600.
This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:24:10 +0000 (19:24 -0300)]
V4L/DVB (13983): [STV6110x] add clk_div member to stv6110x_config structure
Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:23:41 +0000 (19:23 -0300)]
V4L/DVB (13982): [STV090x] setup master clock in stv090x_init instead of stv090x_setup.
This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:23:13 +0000 (19:23 -0300)]
V4L/DVB (13981): [STV6110x] Add a local register map for each instance of the driver.
Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:22:45 +0000 (19:22 -0300)]
V4L/DVB (13980): [STV6110x] Added function stv6110x_write_regs
The function stv6110x_write_regs is used to write several registers at once.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 5 Jan 2010 22:22:07 +0000 (19:22 -0300)]
V4L/DVB (13979): [STV090x] Added possibility to set a fixed TS output clock.
This could be useful for p.e. Common Interface applications where data rate is limited.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mirror_ubuntu-eoan-kernel.git / log