For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_find_matching_node_and_match returns a node pointer with
refcount incremented thus it must be explicitly decremented after the
last usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/pl111/pl111_versatile.c:333:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:340:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:346:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:354:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:402:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVER FOR ARM PL111 CLCD) Cc: David Airlie <airlied@linux.ie> (maintainer:DRM DRIVERS) Cc: Daniel Vetter <daniel@ffwll.ch> (maintainer:DRM DRIVERS) Cc: dri-devel@lists.freedesktop.org (open list:DRM DRIVERS) Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/1554307455-40361-6-git-send-email-wen.yang99@zte.com.cn Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The problem is that regulator_unregister takes the
regulator_list_mutex and then calls flush_work on disable_work. But
regulator_disable_work calls regulator_lock_dependent which will
also take the regulator_list_mutex. Resulting in a deadlock if the
flush_work call actually needs to flush the work.
Fix this issue by moving the flush_work outside of the
regulator_list_mutex. The list mutex is not used to guard the point at
which the delayed work is queued, so its use adds no additional safety.
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The LLVM linker (ld.lld) defaults to removing local relocations, which
causes KASLR boot failures. ld.bfd and ld.gold already handle this
correctly. This adds the explicit instruction "--discard-none" during
the link phase. There is no change in output for ld.bfd and ld.gold,
but ld.lld now produces an image with all the needed relocations.
clang started to error on invalid asm clobber usage in x86 headers
and many bpf program samples failed to build with the message:
CLANG-bpf /data/users/ast/bpf-next/samples/bpf/xdp_redirect_kern.o
In file included from /data/users/ast/bpf-next/samples/bpf/xdp_redirect_kern.c:14:
In file included from ../include/linux/in.h:23:
In file included from ../include/uapi/linux/in.h:24:
In file included from ../include/linux/socket.h:8:
In file included from ../include/linux/uio.h:14:
In file included from ../include/crypto/hash.h:16:
In file included from ../include/linux/crypto.h:26:
In file included from ../include/linux/uaccess.h:5:
In file included from ../include/linux/sched.h:15:
In file included from ../include/linux/sem.h:5:
In file included from ../include/uapi/linux/sem.h:5:
In file included from ../include/linux/ipc.h:9:
In file included from ../include/linux/refcount.h:72:
../arch/x86/include/asm/refcount.h:72:36: error: asm-specifier for input or output variable conflicts with asm clobber list
r->refs.counter, e, "er", i, "cx");
^
../arch/x86/include/asm/refcount.h:86:27: error: asm-specifier for input or output variable conflicts with asm clobber list
r->refs.counter, e, "cx");
^
2 errors generated.
Override volatile() to workaround the problem.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The implementation of IOC_OPAL_ENABLE_DISABLE_MBR handled the value
opal_mbr_data.enable_disable incorrectly: enable_disable is expected
to be one of OPAL_MBR_ENABLE(0) or OPAL_MBR_DISABLE(1). enable_disable
was passed directly to set_mbr_done and set_mbr_enable_disable where
is was interpreted as either OPAL_TRUE(1) or OPAL_FALSE(0). The end
result was that calling IOC_OPAL_ENABLE_DISABLE_MBR with OPAL_MBR_ENABLE
actually disabled the shadow MBR and vice versa.
This patch adds correct conversion from OPAL_MBR_DISABLE/ENABLE to
OPAL_FALSE/TRUE. The change affects existing programs using
IOC_OPAL_ENABLE_DISABLE_MBR but this is typically used only once when
setting up an Opal drive.
Acked-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Scott Bauer <sbauer@plzdonthack.me> Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_node_get returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/imx6q-cpufreq.c:391:4-10: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 348, but without a corresponding object release within this function.
./drivers/cpufreq/imx6q-cpufreq.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 348, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-pm@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/kirkwood-cpufreq.c:127:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
./drivers/cpufreq/kirkwood-cpufreq.c:133:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
and also do some cleanup:
- of_node_put(np);
- np = NULL;
...
of_node_put(np);
The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-pm@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.
Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.
Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.
Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Dan reported, that cleanup path in test_memcg_subtree_control()
triggers a static checker warning:
./tools/testing/selftests/cgroup/test_memcontrol.c:76 \
test_memcg_subtree_control()
error: uninitialized symbol 'child2'.
Fix this by initializing child2 and parent2 variables and
split the cleanup path into few stages.
Signed-off-by: Roman Gushchin <guro@fb.com> Fixes: 84092dbcf901 ("selftests: cgroup: add memory controller self-tests") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Shuah Khan (Samsung OSG) <shuah@kernel.org> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Shuah Khan <shuah@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If CONFIG_PGSTE is not set (e.g. when compiling without KVM), GCC complains:
CC arch/s390/mm/pgtable.o
arch/s390/mm/pgtable.c:413:15: warning: ‘pmd_alloc_map’ defined but not
used [-Wunused-function]
static pmd_t *pmd_alloc_map(struct mm_struct *mm, unsigned long addr)
^~~~~~~~~~~~~
Wrap the function with "#ifdef CONFIG_PGSTE" to silence the warning.
Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The 'func_code' variable gets printed in debug statements without
a prior initialization in multiple functions, as reported when building
with clang:
drivers/s390/crypto/zcrypt_api.c:659:6: warning: variable 'func_code' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (mex->outputdatalength < mex->inputdatalength) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:725:29: note: uninitialized use occurs here
trace_s390_zcrypt_rep(mex, func_code, rc,
^~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:659:2: note: remove the 'if' if its condition is always false
if (mex->outputdatalength < mex->inputdatalength) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:654:24: note: initialize the variable 'func_code' to silence this warning
unsigned int func_code;
^
Add initializations to all affected code paths to shut up the warning
and make the warning output consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The firmware sets BIT(13) in clkflag to mark a divider as fractional
divider. The clock driver copies the clkflag straight to the flags of
the common clock framework. In the common clk framework flags, BIT(13)
is defined as CLK_DUTY_CYCLE_PARENT.
Add a new field to the zynqmp_clk_divider to specify if a divider is a
fractional devider. Set this field based on the clkflag when registering
a divider.
At the same time, unset BIT(13) from clkflag when copying the flags to
the common clk framework flags.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Most rk3288-based boards are derived from the EVB and thus use a PWM
regulator for the logic rail. However, most rk3288-based boards don't
specify the PWM regulator in their device tree. We'll deal with that
by making it critical.
NOTE: it's important to make it critical and not just IGNORE_UNUSED
because all PWMs in the system share the same clock. We don't want
another PWM user to turn the clock on and off and kill the logic rail.
This change is in preparation for actually having the PWMs in the
rk3288 device tree actually point to the proper PWM clock. Up until
now they've all pointed to the clock for the old IP block and they've
all worked due to the fact that rkpwm was IGNORE_UNUSED and that the
clock rates for both clocks were the same.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Microphone detection provides the button detection features on the
Arizona CODECs as such it will be running if the jack is currently
inserted. If the driver is unbound whilst the jack is still inserted
this will cause warnings from the regulator framework as the MICVDD
regulator is put but was never disabled.
Correct this by disabling microphone detection on driver removal and if
the microphone detection was running disable the regulator and put the
runtime reference that was currently held.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It appears that there is a typo in the rk3288 TRM. For
GRF_SOC_CON0[7] it says that 0 means "vepu" and 1 means "vdpu". It's
the other way around.
How do I know? Here's my evidence:
1. Prior to commit 4d3e84f99628 ("clk: rockchip: describe aclk_vcodec
using the new muxgrf type on rk3288") we always pretended that we
were using "aclk_vdpu" and the comment in the code said that this
matched the default setting in the system. In fact the default
setting is 0 according to the TRM and according to reading memory
at bootup. In addition rk3288-based Chromebooks ran like this and
the video codecs worked.
2. With the existing clock code if you boot up and try to enable the
new VIDEO_ROCKCHIP_VPU as a module (and without "clk_ignore_unused"
on the command line), you get errors like "failed to get ack on
domain 'pd_video', val=0x80208". After flipping vepu/vdpu things
init OK.
3. If I export and add both the vepu and vdpu to the list of clocks
for RK3288_PD_VIDEO I can get past the power domain errors, but now
I freeze when the vpu_mmu gets initted.
4. If I just mark the "vdpu" as IGNORE_UNUSED then everything boots up
and probes OK showing that somehow the "vdpu" was important to keep
enabled. This is because we were actually using it as a parent.
5. After this change I can hack "aclk_vcodec_pre" to parent from
"aclk_vepu" using assigned-clocks and the video codec still probes
OK.
6. Rockchip has said so on the mailing list [1].
...so let's fix it.
Let's also add CLK_SET_RATE_PARENT to "aclk_vcodec_pre" as suggested
by Jonas Karlman. Prior to the same commit you could do
clk_set_rate() on "aclk_vcodec" and it would change "aclk_vdpu".
That's because "aclk_vcodec" was a simple gate clock (always gets
CLK_SET_RATE_PARENT) and its direct parent was "aclk_vdpu". After
that commit "aclk_vcodec_pre" gets in the way so we need to add
CLK_SET_RATE_PARENT to it too.
Fixes: 4d3e84f99628 ("clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288") Suggested-by: Jonas Karlman <jonas@kwiboo.se> Suggested-by: Randy Li <ayaka@soulik.info> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The dev->power.direct_complete flag may become set in device_prepare() in
case the device don't have any PM callbacks (dev->power.no_pm_callbacks is
set). This leads to a broken behaviour, when there is child having wakeup
enabled and relies on its parent to be used in the wakeup path.
More precisely, when the direct complete path becomes selected for the
child in __device_suspend(), the propagation of the dev->power.wakeup_path
becomes skipped as well.
Let's address this problem, by checking if the device is a part the wakeup
path or has wakeup enabled, then prevent the direct complete path from
being used.
Reported-by: Loic Pallardy <loic.pallardy@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Comment cleanup ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
In the event of that any data error (like, IRQSTAT[DCE]) occurs
during an eSDHC data transaction where DMA is used for data
transfer to/from the system memory, setting the SYSCTL[RSTD]
register may cause a system hang. If software sets the register
SYSCTL[RSTD] to 1 for error recovery while DMA transferring is
not complete, eSDHC may hang the system bus. This happens because
the software register SYSCTL[RSTD] resets the DMA engine without
waiting for the completion of pending system transactions. This
erratum is to fix this issue.
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
pwrseq_emmc.c implements a HW reset procedure for eMMC chip by driving a
GPIO line.
It registers the .reset() cb on mmc_pwrseq_ops and it registers a system
restart notification handler; both of them perform reset by unconditionally
calling gpiod_set_value().
If the eMMC reset line is tied to a GPIO controller whose driver can sleep
(i.e. I2C GPIO controller), then the kernel would spit warnings when trying
to reset the eMMC chip by means of .reset() mmc_pwrseq_ops cb (that is
exactly what I'm seeing during boot).
Furthermore, on system reset we would gets to the system restart
notification handler with disabled interrupts - local_irq_disable() is
called in machine_restart() at least on ARM/ARM64 - and we would be in
trouble when the GPIO driver tries to sleep (which indeed doesn't happen
here, likely because in my case the machine specific code doesn't call
do_kernel_restart(), I guess..).
This patch fixes the .reset() cb to make use of gpiod_set_value_cansleep(),
so that the eMMC gets reset on boot without complaints, while, since there
isn't that much we can do, we avoid register the restart handler if the
GPIO controller has a sleepy driver (and we spit a dev_notice() message to
let people know)..
This had been tested on a downstream 4.9 kernel with backported
commit 83f37ee7ba33 ("mmc: pwrseq: Add reset callback to the struct
mmc_pwrseq_ops") and commit ae60fb031cf2 ("mmc: core: Don't do eMMC HW
reset when resuming the eMMC card"), because I couldn't boot my board
otherwise. Maybe worth to RFT.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a58e ("hwmon: New f71805f driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f0a7 ("hwmon: New PC87427 hardware monitoring driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6cd ("hwmon/vt1211: Add probing of alternate config index port") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1cd ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently if alloc_skb fails to allocate the skb a null skb is passed to
t4_set_arp_err_handler and this ends up dereferencing the null skb. Avoid
the NULL pointer dereference by checking for a NULL skb and returning
early.
Addresses-Coverity: ("Dereference null return") Fixes: b38a0ad8ec11 ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
clock_getres() in the vDSO library has to preserve the same behaviour
of posix_get_hrtimer_res().
In particular, posix_get_hrtimer_res() does:
sec = 0;
ns = hrtimer_resolution;
where 'hrtimer_resolution' depends on whether or not high resolution
timers are enabled, which is a runtime decision.
The vDSO incorrectly returns the constant CLOCK_REALTIME_RES. Fix this
by exposing 'hrtimer_resolution' in the vDSO datapage and returning that
instead.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[will: Use WRITE_ONCE(), move adr off COARSE path, renumber labels, use 'w' reg] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In a system where, through IORT firmware mappings, the SMMU device is
mapped to a NUMA node that is not online, the kernel bootstrap results
in the following crash:
Unable to handle kernel paging request at virtual address 0000000000001388
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
[0000000000001388] user address but active_mm is swapper
Internal error: Oops: 96000004 [#1] SMP
Modules linked in:
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 5.0.0 #15
pstate: 80c00009 (Nzcv daif +PAN +UAO)
pc : __alloc_pages_nodemask+0x13c/0x1068
lr : __alloc_pages_nodemask+0xdc/0x1068
...
Process swapper/0 (pid: 1, stack limit = 0x(____ptrval____))
Call trace:
__alloc_pages_nodemask+0x13c/0x1068
new_slab+0xec/0x570
___slab_alloc+0x3e0/0x4f8
__slab_alloc+0x60/0x80
__kmalloc_node_track_caller+0x10c/0x478
devm_kmalloc+0x44/0xb0
pinctrl_bind_pins+0x4c/0x188
really_probe+0x78/0x2b8
driver_probe_device+0x64/0x110
device_driver_attach+0x74/0x98
__driver_attach+0x9c/0xe8
bus_for_each_dev+0x84/0xd8
driver_attach+0x30/0x40
bus_add_driver+0x170/0x218
driver_register+0x64/0x118
__platform_driver_register+0x54/0x60
arm_smmu_driver_init+0x24/0x2c
do_one_initcall+0xbc/0x328
kernel_init_freeable+0x304/0x3ac
kernel_init+0x18/0x110
ret_from_fork+0x10/0x1c
Code: f90013b5b9410fa11a9f0694b50014c2 (b9400804)
---[ end trace dfeaed4c373a32da ]--
Change the dev_set_proximity() hook prototype so that it returns a
value and make it return failure if the PXM->NUMA-node mapping
corresponds to an offline node, fixing the crash.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Link: https://lore.kernel.org/linux-arm-kernel/20190315021940.86905-1-wangkefeng.wang@huawei.com/ Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Modifying the VLAN stripping options when a port VLAN is configured
will break traffic for the VSI, and conceptually doesn't make sense,
so don't allow this.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
gcc points out that when CONFIG_GPIOLIB is disabled,
gpiod_get_array_value_cansleep() returns 0 but fails to set its output:
drivers/phy/motorola/phy-mapphone-mdm6600.c: In function 'phy_mdm6600_status':
drivers/phy/motorola/phy-mapphone-mdm6600.c:220:24: error: 'values[0]' is used uninitialized in this function [-Werror=uninitialized]
This could be fixed more generally in gpiolib by returning a failure
code, but for this specific case, the easier workaround is to add a
gpiolib dependency.
Fixes: 5d1ebbda0318 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On platforms where the MUSB and HCI controllers share PHY0, PHY passby
is required when using the HCI controller with the PHY, but it must be
disabled when the MUSB controller is used instead.
Without this, PHY0 passby is always enabled, which results in broken
peripheral mode on such platforms (e.g. H3/H5).
Fixes: ba4bdc9e1dc0 ("PHY: sunxi: Add driver for sunxi usb phy") Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add a required reset to the SDM845 UFS phy to express the PHY reset
bit inside the UFS controller register space. Before this change, this
reset was not expressed in the DT, and the driver utilized two different
callbacks (phy_init and phy_poweron) to implement a two-phase
initialization procedure that involved deasserting this reset between
init and poweron. This abused the two callbacks and diluted their
purpose.
That scheme does not work as regulators cannot be turned off in
phy_poweroff because they were turned on in init, rather than poweron.
The net result is that regulators are left on in suspend that shouldn't
be.
This new scheme gives the UFS reset to the PHY, so that it can fully
initialize itself in a single callback. We can then turn regulators on
during poweron and off during poweroff.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
WARNING: CPU: 0 PID: 19001 at kernel/dma/debug.c:1301 debug_dma_map_sg+0x284/0x3dc
etnaviv etnaviv: DMA-API: mapping sg segment longer than device claims to support [len=3145728] [max=65536]
Modules linked in: ip6t_REJECT nf_reject_ipv6 ip6t_rpfilter xt_tcpudp ipt_REJECT nf_reject_ipv4 xt_conntrack ip_set nfnetlink ebtable_broute ebtable_nat ip6table_raw ip6table_nat nf_nat_ipv6 ip6table_mangle iptable_raw iptable_nat nf_nat_ipv4 nf_nat nf_conntrack nf_defrag_ipv4 nf_defrag_ipv6 libcrc32c iptable_mangle ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter caam_jr error snd_soc_imx_spdif imx_thermal snd_soc_imx_audmux nvmem_imx_ocotp snd_soc_sgtl5000
caam imx_sdma virt_dma coda rc_cec v4l2_mem2mem snd_soc_fsl_ssi snd_soc_fsl_spdif imx_vdoa imx_pcm_dma videobuf2_dma_contig etnaviv dw_hdmi_cec gpu_sched dw_hdmi_ahb_audio imx6q_cpufreq nfsd sch_fq_codel ip_tables x_tables
CPU: 0 PID: 19001 Comm: Xorg Not tainted 4.20.0+ #307
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0019658>] (unwind_backtrace) from [<c001489c>] (show_stack+0x10/0x14)
[<c001489c>] (show_stack) from [<c07fb420>] (dump_stack+0x9c/0xd4)
[<c07fb420>] (dump_stack) from [<c00312dc>] (__warn+0xf8/0x124)
[<c00312dc>] (__warn) from [<c00313d0>] (warn_slowpath_fmt+0x38/0x48)
[<c00313d0>] (warn_slowpath_fmt) from [<c00b14e8>] (debug_dma_map_sg+0x284/0x3dc)
[<c00b14e8>] (debug_dma_map_sg) from [<c046eb40>] (drm_gem_map_dma_buf+0xc4/0x13c)
[<c046eb40>] (drm_gem_map_dma_buf) from [<c04c3314>] (dma_buf_map_attachment+0x38/0x5c)
[<c04c3314>] (dma_buf_map_attachment) from [<c046e728>] (drm_gem_prime_import_dev+0x74/0x104)
[<c046e728>] (drm_gem_prime_import_dev) from [<c046e5bc>] (drm_gem_prime_fd_to_handle+0x84/0x17c)
[<c046e5bc>] (drm_gem_prime_fd_to_handle) from [<c046edd0>] (drm_prime_fd_to_handle_ioctl+0x38/0x4c)
[<c046edd0>] (drm_prime_fd_to_handle_ioctl) from [<c0460efc>] (drm_ioctl_kernel+0x90/0xc8)
[<c0460efc>] (drm_ioctl_kernel) from [<c0461114>] (drm_ioctl+0x1e0/0x3b0)
[<c0461114>] (drm_ioctl) from [<c01cae20>] (do_vfs_ioctl+0x90/0xa48)
[<c01cae20>] (do_vfs_ioctl) from [<c01cb80c>] (ksys_ioctl+0x34/0x60)
[<c01cb80c>] (ksys_ioctl) from [<c0009000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xd81a9fa8 to 0xd81a9ff0)
9fa0: b6c69c88bec613f800000009c00c642ebec613f8b86c4600
9fc0: b6c69c88bec613f8c00c642e00000036012762e00127634800000300012d91f8
9fe0: b6989f18bec613dcb697185cb667be5c
irq event stamp: 47905
hardirqs last enabled at (47913): [<c0098824>] console_unlock+0x46c/0x680
hardirqs last disabled at (47922): [<c0098470>] console_unlock+0xb8/0x680
softirqs last enabled at (47754): [<c000a484>] __do_softirq+0x344/0x540
softirqs last disabled at (47701): [<c0038700>] irq_exit+0x124/0x144
---[ end trace af477747acbcc642 ]---
The reason is the contiguous buffer exceeds the default maximum segment
size of 64K as specified by dma_get_max_seg_size() in
linux/dma-mapping.h. Fix this by providing our own segment size, which
is set to 2GiB to cover the window found in MMUv1 GPUs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
37fe6a42b343 ("x86: Check stack overflow in detail")
added a broad check for the full exception stack area, i.e. it considers
the full exception stack area as valid.
That's wrong in two aspects:
1) It does not check the individual areas one by one
2) #DF, NMI and #MCE are not enabling interrupts which means that a
regular device interrupt cannot happen in their context. In fact if a
device interrupt hits one of those IST stacks that's a bug because some
code path enabled interrupts while handling the exception.
Limit the check to the #DB stack and consider all other IST stacks as
'overflow' or invalid.
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> CC: Bart Van Assche <bvanassche@acm.org> CC: Martin K. Petersen <martin.petersen@oracle.com> CC: Jacky Cao <Jacky.Cao@sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Subsequent code relies on the values that qeth_update_from_chp_desc()
reads from the CHP descriptor. Rather than dealing with weird errors
later on, just handle it properly here.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.
For this reason drop switch_lock from the driver completely in favour of
big domain lock.
There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:
We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The QEMU PowerPC/PSeries machine model was not expecting a self-IPI,
and it may be a bit surprising thing to do, so have irq_work_queue_on
do local queueing when target is the current CPU.
Suggested-by: Steven Rostedt <rostedt@goodmis.org> Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: =?UTF-8?q?C=C3=A9dric=20Le=20Goater?= <clg@kaod.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190409093403.20994-1-npiggin@gmail.com
[ Simplified the preprocessor comments.
Fixed unbalanced curly brackets pointed out by Thomas. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The frame_busy mask is used in frame_done event handling, which is not
invoked for async commits. So an async commit will leave the
frame_busy mask populated after it completes and future commits will start
with the busy mask incorrect.
This showed up on disable after cursor move. I was hitting the "this should
not happen" comment in the frame event worker since frame_busy was set,
we queued the event, but there were no frames pending (since async
also doesn't set that).
Reviewed-by: Fritz Koenig <frkoenig@google.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190130163220.138637-1-sean@poorly.run Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Mamta Shukla <mamtashukla555@gmail.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Sharat Masetty <smasetty@codeaurora.org> Cc: linux-arm-msm@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: freedreno@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org (open list) Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
release resources allocated in mode_set if any of
the hw check fails. Most of these checks are not
necessary and they will be removed in the follow up
patches with state based resource allocations.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/1550107156-17625-4-git-send-email-jsanka@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The kzalloc here was being used without checking the return - if the
kzalloc fails return VCHIQ_ERROR. The call-site of
vchiq_platform_init_state() vchiq_init_state() was not responding
to an allocation failure so checks for != VCHIQ_SUCCESS
and pass VCHIQ_ERROR up to vchiq_platform_init() which then
will fail with -EINVAL.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Reported-by: kbuild test robot <lkp@intel.com> Acked-By: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The number of descendant cgroups and the number of dying
descendant cgroups are currently synchronized using the cgroup_mutex.
The number of descendant cgroups will be required by the cgroup v2
freezer, which will use it to determine if a cgroup is frozen
(depending on total number of descendants and number of frozen
descendants). It's not always acceptable to grab the cgroup_mutex,
especially from quite hot paths (e.g. exit()).
To avoid this, let's additionally synchronize these counters using
the css_set_lock.
So, it's safe to read these counters with either cgroup_mutex or
css_set_lock locked, and for changing both locks should be acquired.
The per-CPU variable batched_entropy_uXX is protected by get_cpu_var().
This is just a preempt_disable() which ensures that the variable is only
from the local CPU. It does not protect against users on the same CPU
from another context. It is possible that a preemptible context reads
slot 0 and then an interrupt occurs and the same value is read again.
The above scenario is confirmed by lockdep if we add a spinlock:
| ================================
| WARNING: inconsistent lock state
| 5.1.0-rc3+ #42 Not tainted
| --------------------------------
| inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
| ksoftirqd/9/56 [HC0[0]:SC1[1]:HE0:SE0] takes:
| (____ptrval____) (batched_entropy_u32.lock){+.?.}, at: get_random_u32+0x3e/0xe0
| {SOFTIRQ-ON-W} state was registered at:
| _raw_spin_lock+0x2a/0x40
| get_random_u32+0x3e/0xe0
| new_slab+0x15c/0x7b0
| ___slab_alloc+0x492/0x620
| __slab_alloc.isra.73+0x53/0xa0
| kmem_cache_alloc_node+0xaf/0x2a0
| copy_process.part.41+0x1e1/0x2370
| _do_fork+0xdb/0x6d0
| kernel_thread+0x20/0x30
| kthreadd+0x1ba/0x220
| ret_from_fork+0x3a/0x50
…
| other info that might help us debug this:
| Possible unsafe locking scenario:
|
| CPU0
| ----
| lock(batched_entropy_u32.lock);
| <Interrupt>
| lock(batched_entropy_u32.lock);
|
| *** DEADLOCK ***
|
| stack backtrace:
| Call Trace:
…
| kmem_cache_alloc_trace+0x20e/0x270
| ipmi_alloc_recv_msg+0x16/0x40
…
| __do_softirq+0xec/0x48d
| run_ksoftirqd+0x37/0x60
| smpboot_thread_fn+0x191/0x290
| kthread+0xfe/0x130
| ret_from_fork+0x3a/0x50
Add a spinlock_t to the batched_entropy data structure and acquire the
lock while accessing it. Acquire the lock with disabled interrupts
because this function may be used from interrupt context.
Remove the batched_entropy_reset_lock lock. Now that we have a lock for
the data scructure, we can access it from a remote CPU.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the system boots with random.trust_cpu=1 it doesn't initialize the
per-NUMA CRNGs because it skips the rest of the CRNG startup code. This
means that the code from 1e7f583af67b ("random: make /dev/urandom scalable
for silly userspace programs") is not used when random.trust_cpu=1.
The call to invalidate_batched_entropy() was also missing. This is
important for architectures like PPC and S390 which only have the
arch_get_random_seed_* functions.
Fixes: 39a8883a2b98 ("random: add a config option to trust the CPU's hwrng") Signed-off-by: Jon DeVree <nuxi@vault24.org> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
With STRICT_KERNEL_RWX enabled anything marked __init is placed at a 16M
boundary. This is necessary so that it can be repurposed later with
different permissions. However, in kernels with text larger than 16M,
this pushes early_setup past 32M, incapable of being reached by the
branch instruction.
Fix this by setting the CTR and branching there instead.
Fixes: 1e0fc9d1eb2b ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs") Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Fix it to work on BE by using DOTSYM()] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When booted with "topology_updates=no", or when "off" is written to
/proc/powerpc/topology_updates, NUMA reassignments are inhibited for
PRRN and VPHN events. However, migration and suspend unconditionally
re-enable reassignments via start_topology_update(). This is
incoherent.
Check the topology_updates_enabled flag in
start/stop_topology_update() so that callers of those APIs need not be
aware of whether reassignments are enabled. This allows the
administrative decision on reassignments to remain in force across
migrations and suspensions.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit 2da78092dda "block: Fix dev_t minor allocation lifetime"
specifically moved blk_free_devt(dev->devt) call to part_release()
to avoid reallocating device number before the device is fully
shutdown.
However, it can cause use-after-free on gendisk in get_gendisk().
We use md device as example to show the race scenes:
Process1 Worker Process2
md_free
blkdev_open
del_gendisk
add delete_partition_work_fn() to wq
__blkdev_get
get_gendisk
put_disk
disk_release
kfree(disk)
find part from ext_devt_idr
get_disk_and_module(disk)
cause use after free
delete_partition_work_fn
put_device(part)
part_release
remove part from ext_devt_idr
Before <devt, hd_struct pointer> is removed from ext_devt_idr by
delete_partition_work_fn(), we can find the devt and then access
gendisk by hd_struct pointer. But, if we access the gendisk after
it have been freed, it can cause in use-after-freeon gendisk in
get_gendisk().
We fix this by adding a new helper blk_invalidate_devt() in
delete_partition() and del_gendisk(). It replaces hd_struct
pointer in idr with value 'NULL', and deletes the entry from
idr in part_release() as we do now.
Thanks to Jan Kara for providing the solution and more clear comments
for the code.
Fixes: 2da78092dda1 ("block: Fix dev_t minor allocation lifetime") Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ctrl_check_input() function is called from pvr2_ctrl_range_check().
It's supposed to validate user supplied input and return true or false
depending on whether the input is valid or not. The problem is that
negative shifts or shifts greater than 31 are undefined in C. In
practice with GCC they result in shift wrapping so this function returns
true for some inputs which are not valid and this could result in a
buffer overflow:
drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname()
warn: uncapped user index 'names[val]'
The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create()
and the highest valid bit is BIT(4).
Fixes: 7fb20fa38caa ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix au0828_analog_stream_enable() to check if device is in the right
state first. When unbind happens while bind is in progress, usbdev
pointer could be invalid in au0828_analog_stream_enable() and a call
to usb_ifnum_to_if() will result in the null pointer dereference.
This problem is found with the new media_dev_allocator.sh test.
In audit_rule_change(), audit_data_to_entry() is firstly invoked to
translate the payload data to the kernel's rule representation. In
audit_data_to_entry(), depending on the audit field type, an audit tree may
be created in audit_make_tree(), which eventually invokes kmalloc() to
allocate the tree. Since this tree is a temporary tree, it will be then
freed in the following execution, e.g., audit_add_rule() if the message
type is AUDIT_ADD_RULE or audit_del_rule() if the message type is
AUDIT_DEL_RULE. However, if the message type is neither AUDIT_ADD_RULE nor
AUDIT_DEL_RULE, i.e., the default case of the switch statement, this
temporary tree is not freed.
To fix this issue, only allocate the tree when the type is AUDIT_ADD_RULE
or AUDIT_DEL_RULE.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver returns an error if unsupported media bus pixel code is
requested by VIDIOC_SUBDEV_S_FMT.
But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst,
Drivers must not return an error solely because the requested format
doesn't match the device capabilities. They must instead modify the
format to match what the hardware can provide.
So select default format code and return success in that case.
In preparation for adding asynchronous subdevice support to the driver,
don't acquire v4l2_clk from the driver .probe() callback as that may
fail if the clock is provided by a bridge driver which may be not yet
initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper
which is going to be converted to v4l2_subdev_internal_ops.registered()
callback, executed only when the bridge driver is ready.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Even if this case shouldn't happen when controller is properly programmed,
it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and
just finish the tasklet call.
Uncore PMU drivers face an awkward cyclic dependency wherein:
- They have to pick a valid online CPU to associate with before
registering the PMU device, since it will get exposed to userspace
immediately.
- The PMU registration has to be be at least partly complete before
hotplug events can be handled, since trying to migrate an
uninitialised context would be bad.
- The hotplug handler has to be ready as soon as a CPU is chosen, lest
it go offline without the user-visible cpumask value getting updated.
The arm-cci driver has tried to solve this by using get_cpu() to pick
the current CPU and prevent it from disappearing while both
registrations are performed, but that results in taking mutexes with
preemption disabled, which makes certain configurations very unhappy:
It is not feasible to resolve all the possible races outside of the perf
core itself, so address the immediate bug by following the example of
nearly every other PMU driver and not even trying to do so. Registering
the hotplug notifier first should minimise the window in which things
can go wrong, so that's about as much as we can reasonably do here. This
also revealed an additional race in assigning the global pointer too
late relative to the hotplug notifier, which gets fixed in the process.
Reported-by: Li, Meng <Meng.Li@windriver.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This is mostly a revert of commit 55bb6a633c33 ("clk: rockchip: mark
noc and some special clk as critical on rk3288") except that we're
keeping "pmu_hclk_otg0" as critical still.
NOTE: turning these clocks off doesn't seem to do a whole lot in terms
of power savings (checking the power on the logic rail). It appears
to save maybe 1-2mW. ...but still it seems like we should turn the
clocks off if they aren't needed.
About "pmu_hclk_otg0" (the one clock from the original commit we're
still keeping critical) from an email thread:
> pmu ahb clock
>
> Function: Clock to pmu module when hibernation and/or ADP is
> enabled. Must be greater than or equal to 30 MHz.
>
> If the SOC design does not support hibernation/ADP function, only have
> hclk_otg, this clk can be switched according to the usage of otg.
> If the SOC design support hibernation/ADP, has two clocks, hclk_otg and
> pmu_hclk_otg0.
> Hclk_otg belongs to the closed part of otg logic, which can be switched
> according to the use of otg.
>
> pmu_hclk_otg0 belongs to the always on part.
>
> As for whether pmu_hclk_otg0 can be turned off when otg is not in use,
> we have not tested. IC suggest make pmu_hclk_otg0 always on.
For the rest of the clocks:
atclk: No documentation about this clock other than that it goes to
the CPU. CPU functions fine without it on. Maybe needed for JTAG?
jtag: Presumably this clock is only needed if you're debugging with
JTAG. It doesn't seem like it makes sense to waste power for every
rk3288 user. In any case to do JTAG you'd need private patches to
adjust the pinctrl the mux the JTAG out anyway.
pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two
clocks on only during kernel panics in order to access some coresight
registers. Since nothing in the upstream kernel does this we should
be able to leave them off safely. Maybe also needed for JTAG?
hsicphy12m_xin12m: There is no indication of why this clock would need
to be turned on for boards that don't use HSIC.
pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn
these 4 clocks on only when doing DDR transitions and they are off
otherwise. I see no reason why they'd need to be on in the upstream
kernel which doesn't support DDRFreq.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_find_compatible_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:76:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:82:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: linux-samsung-soc@vger.kernel.org Cc: linux-gpio@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.
According to the logitech_hidpp_2.0_specification_draft_2012-06-04.pdf doc:
https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf
We should use a register-access-protocol request using the short input /
output report ids. This is necessary because 27MHz HID++ receivers have
a max-packetsize on their HIP++ endpoint of 8, so they cannot support
long reports. Using a feature-access-protocol request (which is always
long or very-long) with these will cause a timeout error, followed by
the hidpp driver treating the device as not being HID++ capable.
This commit fixes this by switching to using a rap request to get the
protocol version.
Besides being tested with a (046d:c517) 27MHz receiver with various
27MHz keyboards and mice, this has also been tested to not cause
regressions on a non-unifying dual-HID++ nano receiver (046d:c534) with
k270 and m185 HID++-2.0 devices connected and on a unifying/dj receiver
(046d:c52b) with a HID++-2.0 Logitech Rechargeable Touchpad T650.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none
is given. This address was found when enabling Bluetooth on multiple
Intel Edison modules. It also contains the sequence 43341B, the name
the chip identifies itself as. Using the same BD_ADDR is problematic
when having multiple Intel Edison modules in each others range.
The default address also has the LAA (locally administered address)
bit set which prevents a BNEP device from being created, needed for
BT tethering.
Add this to the list of black listed default MAC addresses and let
the user configure a valid one using f.i.
`btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx`
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ferry Toth <ftoth@exalondelft.nl> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Randy reported objtool triggered on his (GCC-7.4) build:
lib/strncpy_from_user.o: warning: objtool: strncpy_from_user()+0x315: call to __ubsan_handle_add_overflow() with UACCESS enabled
lib/strnlen_user.o: warning: objtool: strnlen_user()+0x337: call to __ubsan_handle_sub_overflow() with UACCESS enabled
This is due to UBSAN generating signed-overflow-UB warnings where it
should not. Prior to GCC-8 UBSAN ignored -fwrapv (which the kernel
uses through -fno-strict-overflow).
Make the functions use 'unsigned long' throughout.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: luto@kernel.org Link: http://lkml.kernel.org/r/20190424072208.754094071@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In-NMI warnings have been added to vmalloc_fault() via:
ebc8827f75 ("x86: Barf when vmalloc and kmemcheck faults happen in NMI")
back in the time when our NMI entry code could not cope with nested NMIs.
These days, it's perfectly fine to take a fault in NMI context and we
don't have to care about the fact that IRET from the fault handler might
cause NMI nesting.
This warning has already been removed from 32-bit implementation of
vmalloc_fault() in:
6863ea0cda8 ("x86/mm: Remove in_nmi() warning from vmalloc_fault()")
but the 64-bit version was omitted.
Remove the bogus warning also from 64-bit implementation of vmalloc_fault().
The __put_user() macro evaluates it's @ptr argument inside the
__uaccess_begin() / __uaccess_end() region. While this would normally
not be expected to be an issue, an UBSAN bug (it ignored -fwrapv,
fixed in GCC 8+) would transform the @ptr evaluation for:
drivers/gpu/drm/i915/i915_gem_execbuffer.c: if (unlikely(__put_user(offset, &urelocs[r-stack].presumed_offset))) {
into a signed-overflow-UB check and trigger the objtool AC validation.
Finish this commit:
2a418cf3f5f1 ("x86/uaccess: Don't leak the AC flag into __put_user() value evaluation")
and explicitly evaluate all 3 arguments early.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: luto@kernel.org Fixes: 2a418cf3f5f1 ("x86/uaccess: Don't leak the AC flag into __put_user() value evaluation") Link: http://lkml.kernel.org/r/20190424072208.695962771@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The test robot reported a wrong assignment of a per-CPU variable which
it detected by using sparse and sent a report. The assignment itself is
correct. The annotation for sparse was wrong and hence the report.
The first pointer is a "normal" pointer and points to the per-CPU memory
area. That means that the __percpu annotation has to be moved.
Move the __percpu annotation to pointer which points to the per-CPU
area. This change affects only the sparse tool (and is ignored by the
compiler).
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: f97f8f06a49fe ("smpboot: Provide infrastructure for percpu hotplug threads") Link: http://lkml.kernel.org/r/20190424085253.12178-1-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When building x86 with Clang LTO and CFI, CFI jump regions are
automatically added to the end of the .text section late in linking. As a
result, the _etext position was being labelled before the appended jump
regions, causing confusion about where the boundaries of the executable
region actually are in the running kernel, and broke at least the fault
injection code. This moves the _etext mark to outside (and immediately
after) the .text area, as it already the case on other architectures
(e.g. arm64, arm).
When releasing the vfio-ccw mdev, we currently do not release
any existing channel program and its pinned pages. This can
lead to the following warning:
[1038876.561565] WARNING: CPU: 2 PID: 144727 at drivers/vfio/vfio_iommu_type1.c:1494 vfio_sanity_check_pfn_list+0x40/0x70 [vfio_iommu_type1]
Similarly we do not free the channel program when we are removing
the vfio-ccw device. Let's fix this by resetting the device and freeing
the channel program and pinned pages in the release path. For the remove
path we can just quiesce the device, since in the remove path the mediated
device is going away for good and so we don't need to do a full reset.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <ae9f20dc8873f2027f7b3c5d2aaa0bdfe06850b8.1554756534.git.alifm@linux.ibm.com> Acked-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently we call flush_workqueue while holding the subchannel
spinlock. But flush_workqueue function can go to sleep, so
do not call the function while holding the spinlock.
When two netdev have same link local addresses (such as vlan and non
vlan), two rdma cm listen id should be able to bind to following different
addresses.
Currently run_cache_set() has no return value, if there is failure in
bch_journal_replay(), the caller of run_cache_set() has no idea about
such failure and just continue to execute following code after
run_cache_set(). The internal failure is triggered inside
bch_journal_replay() and being handled in async way. This behavior is
inefficient, while failure handling inside bch_journal_replay(), cache
register code is still running to start the cache set. Registering and
unregistering code running as same time may introduce some rare race
condition, and make the code to be more hard to be understood.
This patch adds return value to run_cache_set(), and returns -EIO if
bch_journal_rreplay() fails. Then caller of run_cache_set() may detect
such failure and stop registering code flow immedidately inside
register_cache_set().
If journal replay fails, run_cache_set() can report error immediately
to register_cache_set(). This patch makes the failure handling for
bch_journal_replay() be in synchronized way, easier to understand and
debug, and avoid poetential race condition for register-and-unregister
in same time.
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The reason is in journal_reclaim(), when discard is enabled, we send
discard command and reclaim those journal buckets whose seq is old
than the last_seq_now, but before we write a journal with last_seq_now,
the machine is restarted, so the journal with the last_seq_now is not
written to the journal bucket, and the last_seq_wrote in the newest
journal is old than last_seq_now which we expect to be, so when we doing
replay, journals from last_seq_wrote to last_seq_now are missing.
It's hard to write a journal immediately after journal_reclaim(),
and it harmless if those missed journal are caused by discarding
since those journals are already wrote to btree node. So, if miss
seqs are started from the beginning journal, we treat it as normal,
and only print a message to show the miss journal, and point out
it maybe caused by discarding.
Patch v2 add a judgement condition to ignore the missed journal
only when discard enabled as Coly suggested.
(Coly Li: rebase the patch with other changes in bch_journal_replay())
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com> Tested-by: Dennis Schridde <devurandom@gmx.net> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When failure happens inside bch_journal_replay(), calling
cache_set_err_on() and handling the failure in async way is not a good
idea. Because after bch_journal_replay() returns, registering code will
continue to execute following steps, and unregistering code triggered
by cache_set_err_on() is running in same time. First it is unnecessary
to handle failure and unregister cache set in an async way, second there
might be potential race condition to run register and unregister code
for same cache set.
So in this patch, if failure happens in bch_journal_replay(), we don't
call cache_set_err_on(), and just print out the same error message to
kernel message buffer, then return -EIO immediately caller. Then caller
can detect such failure and handle it in synchrnozied way.
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When nbytes < 4, end is wronlgy set to a negative value which, due to
uint, is then interpreted to a large value leading to a deadlock in the
following code.
If we timeout the admin startup sequence we might not yet have
an I/O tagset allocated which causes the teardown sequence to crash.
Make nvme_tcp_teardown_io_queues safe by not iterating inflight tags
if the tagset wasn't allocated.
If we timeout the admin startup sequence we might not yet have
an I/O tagset allocated which causes the teardown sequence to crash.
Make nvme_tcp_teardown_io_queues safe by not iterating inflight tags
if the tagset wasn't allocated.
projects / mirror_ubuntu-disco-kernel.git / log