Ursula Braun [Mon, 8 Mar 2010 20:36:56 +0000 (20:36 +0000)]
qeth: no recovery after layer mismatch (z/VM NICs)
Depending on their definition in z/VM, virtual devices for z/VM
VSWITCH or GuestLAN must be configured either in layer2 or in
layer3 mode. If qeth detects a layer mismatch, device activation
fails. Trying to recover from this error cannot help; thus
scheduling a recovery should be avoided.
In addition, since recovery is forbidden during online setting of
a qeth device, existence of its network device is guaranteed for all
dev_close() calls in qeth. The corresponding checks can be removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 8 Mar 2010 20:36:55 +0000 (20:36 +0000)]
qeth: set promisc off after trace disabling failure
If HiperSockets Network Traffic Analyzer is switched off, but trace
disabling fails somehow, the qeth driver does not switch off its
promisc mode status. A following sniffer reactivation fails, since
qeth does not see a need to reenable tracing.
At the same time the code analyzing results of trace commands is
restructured.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Mon, 8 Mar 2010 20:36:54 +0000 (20:36 +0000)]
qeth: l3 send dhcp in non pass thru mode
dhcp frames are valid IPv4 packets so there is no need to send them
in pass thru mode. This allows dhcp packets to pass HiperSockets.
Also the dhcp release frame is send out correctly with this patch.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 8 Mar 2010 20:36:53 +0000 (20:36 +0000)]
qeth: enable kmsg hash processing in qeth_core_sys.c
provide qeth kmsg definitions to enable hash string generation for
kernel message created with dev_err().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the large effort I'm trying to help with getting all the downstreamed
code from windriver forward ported to the upstream tree
Origional commit message
Restore check to filter out inadverdently received messages
This patch reimplements a check that allows TIPC to discard messages
that are not intended for it. This check was present in TIPC 1.5/1.6,
but was removed by accident during the development of TIPC 1.7; it has
now been updated to account for new features present in TIPC 1.7 and
reinserted into TIPC. The main benefit of this check is to filter
out messages arriving from orphaned link endpoints, which can arise
when a node exits the network and then re-enters it with a different
TIPC network address (i.e. <Z.C.N> value).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Origionally-authored-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 8 Mar 2010 20:20:58 +0000 (12:20 -0800)]
tipc: fix endianness on tipc subscriber messages
Remove htohl implementation from tipc
I was working on forward porting the downstream commits for TIPC and ran accross this one:
http://tipc.cslab.ericsson.net/cgi-bin/gitweb.cgi?p=people/allan/tipc.git;a=commitdiff;h=894279b9437b63cbb02405ad5b8e033b51e4e31e
I was going to just take it, when I looked closer and noted what it was doing.
This is basically a routine to byte swap fields of data in sent/received packets
for tipc, dependent upon the receivers guessed endianness of the peer when a
connection is established. Asside from just seeming silly to me, it appears to
violate the latest RFC draft for tipc:
http://tipc.sourceforge.net/doc/draft-spec-tipc-02.txt
Which, according to section 4.2 and 4.3.3, requires that all fields of all
commands be sent in network byte order. So instead of just taking this patch,
instead I'm removing the htohl function and replacing the calls with calls to
ntohl in the rx path and htonl in the send path.
As part of this fix, I'm also changing the subscr_cancel function, which
searches the list of subscribers, using a memcmp of the entire subscriber list,
for the entry to tear down. unfortunately it memcmps the entire tipc_subscr
structure which has several bits that are private to the local side, so nothing
will ever match. section 5.2 of the draft spec indicates the <type,upper,lower>
tuple should uniquely identify a subscriber, so convert subscr_cancel to just
match on those fields (properly endian swapped).
I've tested this using the tipc test suite, and its passed without issue.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barry Song [Mon, 8 Mar 2010 20:13:57 +0000 (12:13 -0800)]
can: fix bfin_can build error after alloc_candev() change
Looks like commit a6e4bc530403 didn't include updates to drivers so the
Blackfin CAN driver fails to build now.
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 8 Mar 2010 19:32:01 +0000 (11:32 -0800)]
tcp: Fix tcp_make_synack()
Commit 4957faad (TCPCT part 1g: Responder Cookie => Initiator), part
of TCP_COOKIE_TRANSACTION implementation, forgot to correctly size
synack skb in case user data must be included.
Many thanks to Mika Pentillä for spotting this error.
Reported-by: Penttillä Mika <mika.penttila@ixonos.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 8 Mar 2010 03:20:00 +0000 (03:20 +0000)]
net: fix route cache rebuilds
We added an automatic route cache rebuilding in commit 1080d709fb9d8cd43
but had to correct few bugs. One of the assumption of original patch,
was that entries where kept sorted in a given way.
This assumption is known to be wrong (commit 1ddbcb005c395518 gave an
explanation of this and corrected a leak) and expensive to respect.
Paweł Staszewski reported to me one of his machine got its routing cache
disabled after few messages like :
[ 2677.850065] Route hash chain too long!
[ 2677.850080] Adjust your secret_interval!
[82839.662993] Route hash chain too long!
[82839.662996] Adjust your secret_interval!
[155843.731650] Route hash chain too long!
[155843.731664] Adjust your secret_interval!
[155843.811881] Route hash chain too long!
[155843.811891] Adjust your secret_interval!
[155843.858209] vlan0811: 5 rebuilds is over limit, route caching
disabled
[155843.858212] Route hash chain too long!
[155843.858213] Adjust your secret_interval!
This is because rt_intern_hash() might be fooled when computing a chain
length, because multiple entries with same keys can differ because of
TOS (or mark/oif) bits.
In the rare case the fast algorithm see a too long chain, and before
taking expensive path, we call a helper function in order to not count
duplicates of same routes, that only differ with tos/mark/oif bits. This
helper works with data already in cpu cache and is not be very
expensive, despite its O(N^2) implementation.
Paweł Staszewski sucessfully tested this patch on his loaded router.
Reported-and-tested-by: Paweł Staszewski <pstaszewski@itcare.pl> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Validate all sections of unified fw image, before accessing them,
to avoid seg fault.
Signed-off-by: Sucheta Chakraborty <sucheta@dut6195.unminc.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For promiscuous mode, driver send request to device for deleting
multicast addresses and again it send request for adding them back
while exiting from this mode, this is bad for performance.
Just setting device in promiscuous mode is enough, no need to del/add
multicast addresses.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics added for lro/lso bytes, count for tx stop queue and
wake queue and skb alloc failure count.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 5 Mar 2010 21:03:35 +0000 (21:03 +0000)]
bridge: Fix RCU race in br_multicast_stop
Thanks to Paul McKenny for pointing out that it is incorrect to use
synchronize_rcu_bh to ensure that pending callbacks have completed.
Instead we should use rcu_barrier_bh.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 5 Mar 2010 21:07:39 +0000 (21:07 +0000)]
bridge: Use RCU list primitive in __br_mdb_ip_get
As Paul McKenney correctly pointed out, __br_mdb_ip_get needs
to use the RCU list walking primitive in order to work correctly
on platforms where data-dependency ordering is not guaranteed.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
cpmac: fallback to switch mode if no PHY chip found
If we were unable to detect a PHY on any of the MDIO bus id we tried instead of
bailing out with -ENODEV, assume the MAC is connected to a switch and use MDIO
bus 0. This unbreaks quite a lot of devices out there whose switch cannot be
detected.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Despite what the comment above CPMAC_SKB_SIZE says, the hardware also
needs to account for the FCS length in a received frame. This patch fix
the receiving of 802.1q frames which have 4 more bytes. While at it
unhardcode the definition and use the one from if_vlan.h.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Sat, 6 Mar 2010 08:31:50 +0000 (08:31 +0000)]
MAINTAINER: Correct CAN Maintainer responsibilities and paths
Update the CAN Maintainer responsibilities and add source paths.
Additional the SocketCAN core ML is not subscribers-only anymore.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petko Manolov [Sun, 7 Mar 2010 06:10:01 +0000 (06:10 +0000)]
another pegasus usb net device
This one removes trailing whitespace in pegasus.h and more importantly
adds new Pegasus compatible device.
Signed-off-by: Julian Brown <julian@codesourcery.com> Signed-off-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sat, 6 Mar 2010 01:14:09 +0000 (01:14 +0000)]
bridge: cleanup: remove unneed check
We dereference "port" on the lines immediately before and immediately
after the test so port should hopefully never be null here.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: fix packet corruption and tx hang during NFSv2
when receiving a particular type of NFS v2 UDP traffic, the hardware could
DMA some bad data and then hang, possibly corrupting memory.
Disable the NFS parsing in this hardware, verified to fix the bug.
Originally reported and reproduced by RedHat's Neil Horman CC: nhorman@tuxdriver.com Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow [Thu, 4 Mar 2010 04:37:16 +0000 (04:37 +0000)]
typhoon: fix incorrect use of smp_wmb()
The typhoon driver was incorrectly using smp_wmb() to order memory
accesses against IO to the NIC in a few instances. Use wmb() instead,
which is required to actually order between memory types.
Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Thu, 4 Mar 2010 08:21:53 +0000 (08:21 +0000)]
ethtool: Add direct access to ops->get_sset_count
On 03/04/2010 09:26 AM, Ben Hutchings wrote:
> On Thu, 2010-03-04 at 00:51 -0800, Jeff Kirsher wrote:
>> From: Jeff Garzik<jgarzik@redhat.com>
>>
>> This patch is an alternative approach for accessing string
>> counts, vs. the drvinfo indirect approach. This way the drvinfo
>> space doesn't run out, and we don't break ABI later.
> [...]
>> --- a/net/core/ethtool.c
>> +++ b/net/core/ethtool.c
>> @@ -214,6 +214,10 @@ static noinline int ethtool_get_drvinfo(struct net_device *dev, void __user *use
>> info.cmd = ETHTOOL_GDRVINFO;
>> ops->get_drvinfo(dev,&info);
>>
>> + /*
>> + * this method of obtaining string set info is deprecated;
>> + * consider using ETHTOOL_GSSET_INFO instead
>> + */
>
> This comment belongs on the interface (ethtool.h) not the
> implementation.
Debatable -- the current comment is located at the callsite of
ops->get_sset_count(), which is where an implementor might think to add
a new call. Not all the numeric fields in ethtool_drvinfo are obtained
from ->get_sset_count().
Hence the "some" in the attached patch to include/linux/ethtool.h,
addressing your comment.
> [...]
>> +static noinline int ethtool_get_sset_info(struct net_device *dev,
>> + void __user *useraddr)
>> +{
> [...]
>> + /* calculate size of return buffer */
>> + for (i = 0; i< 64; i++)
>> + if (sset_mask& (1ULL<< i))
>> + n_bits++;
> [...]
>
> We have a function for this:
>
> n_bits = hweight64(sset_mask);
Agreed.
I've attached a follow-up patch, which should enable my/Jeff's kernel
patch to be applied, followed by this one.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Wed, 3 Mar 2010 22:51:50 +0000 (22:51 +0000)]
ethtool: Add direct access to ops->get_sset_count
This patch is an alternative approach for accessing string
counts, vs. the drvinfo indirect approach. This way the drvinfo
space doesn't run out, and we don't break ABI later.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Brown [Fri, 5 Mar 2010 09:12:34 +0000 (09:12 +0000)]
net: smc91x: Support Qualcomm MSM development boards.
Signed-off-by: David Brown <davidb@quicinc.com> Signed-off-by: Daniel Walker <dwalker@codeaurora.org> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:46 +0000 (18:01 +0000)]
x25: use limited socket backlog
Make x25 adapt to the limited socket backlog change.
Cc: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:45 +0000 (18:01 +0000)]
tipc: use limited socket backlog
Make tipc adapt to the limited socket backlog change.
Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:44 +0000 (18:01 +0000)]
sctp: use limited socket backlog
Make sctp adapt to the limited socket backlog change.
Cc: Vlad Yasevich <vladislav.yasevich@hp.com> Cc: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:43 +0000 (18:01 +0000)]
llc: use limited socket backlog
Make llc adapt to the limited socket backlog change.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:42 +0000 (18:01 +0000)]
udp: use limited socket backlog
Make udp adapt to the limited socket backlog change.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:41 +0000 (18:01 +0000)]
tcp: use limited socket backlog
Make tcp adapt to the limited socket backlog change.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Thu, 4 Mar 2010 18:01:40 +0000 (18:01 +0000)]
net: add limit for socket backlog
We got system OOM while running some UDP netperf testing on the loopback
device. The case is multiple senders sent stream UDP packets to a single
receiver via loopback on local host. Of course, the receiver is not able
to handle all the packets in time. But we surprisingly found that these
packets were not discarded due to the receiver's sk->sk_rcvbuf limit.
Instead, they are kept queuing to sk->sk_backlog and finally ate up all
the memory. We believe this is a secure hole that a none privileged user
can crash the system.
The root cause for this problem is, when the receiver is doing
__release_sock() (i.e. after userspace recv, kernel udp_recvmsg ->
skb_free_datagram_locked -> release_sock), it moves skbs from backlog to
sk_receive_queue with the softirq enabled. In the above case, multiple
busy senders will almost make it an endless loop. The skbs in the
backlog end up eat all the system memory.
The issue is not only for UDP. Any protocols using socket backlog is
potentially affected. The patch adds limit for socket backlog so that
the backlog size cannot be expanded endlessly.
Reported-by: Alex Shi <alex.shi@intel.com> Cc: David Miller <davem@davemloft.net> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi> Cc: Patrick McHardy <kaber@trash.net> Cc: Vlad Yasevich <vladislav.yasevich@hp.com> Cc: Sridhar Samudrala <sri@us.ibm.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Allan Stephens <allan.stephens@windriver.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 4 Mar 2010 11:32:16 +0000 (03:32 -0800)]
rndis_wlan: correct multicast_list handling V3
My previous patch (655ffee284dfcf9a24ac0343f3e5ee6db85b85c5) added locking in
a bad way. Because rndis_set_oid can sleep, there is need to prepare multicast
addresses into local buffer under netif_addr_lock first, then call
rndis_set_oid outside. This caused reorganizing of the whole function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Wed, 3 Mar 2010 08:18:58 +0000 (08:18 +0000)]
gianfar: Fix TX ring processing on SMP machines
Starting with commit a3bc1f11e9b867a4f49505 ("gianfar: Revive SKB
recycling") gianfar driver sooner or later stops transmitting any
packets on SMP machines.
start_xmit() prepares new skb for transmitting, generally it does
three things:
1. sets up all BDs (marks them ready to send), except the first one.
2. stores skb into tx_queue->tx_skbuff so that clean_tx_ring()
would cleanup it later.
3. sets up the first BD, i.e. marks it ready.
Here is what clean_tx_ring() does:
1. reads skbs from tx_queue->tx_skbuff
2. checks if the *last* BD is ready. If it's still ready [to send]
then it it isn't transmitted, so clean_tx_ring() returns.
Otherwise it actually cleanups BDs. All is OK.
Now, if there is just one BD, code flow:
- start_xmit(): stores skb into tx_skbuff. Note that the first BD
(which is also the last one) isn't marked as ready, yet.
- clean_tx_ring(): sees that skb is not null, *and* its lstatus
says that it is NOT ready (like if BD was sent), so it cleans
it up (bad!)
- start_xmit(): marks BD as ready [to send], but it's too late.
We can fix this simply by reordering lstatus/tx_skbuff writes.
Reported-by: Martyn Welch <martyn.welch@ge.com> Bisected-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com> Tested-by: Martyn Welch <martyn.welch@ge.com> Cc: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Cc: Stable <stable@vger.kernel.org> [2.6.33] Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow [Wed, 3 Mar 2010 16:33:10 +0000 (16:33 +0000)]
r8169: use correct barrier between cacheable and non-cacheable memory
r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.
Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
What happens is that, when the tipc module in inserted it enters a standalone
node mode in which communication to its own address is allowed <0.0.0> but not
to other addresses, since the appropriate data structures have not been
allocated yet (specifically the tipc_net pointer). There is nothing stopping a
client from trying to send such a message however, and if that happens, we
attempt to dereference tipc_net.zones while the pointer is still NULL, and
explode. The fix is pretty straightforward. Since these oopses all arise from
the dereference of global pointers prior to their assignment to allocated
values, and since these allocations are small (about 2k total), lets convert
these pointers to static arrays of the appropriate size. All the accesses to
these bits consider 0/NULL to be a non match when searching, so all the lookups
still work properly, and there is no longer a chance of a bad dererence
anywhere. As a bonus, this lets us eliminate the setup/teardown routines for
those pointers, and elimnates the need to preform any locking around them to
prevent access while their being allocated/freed.
I've updated the tipc_net structure to behave this way to fix the exact reported
problem, and also fixed up the tipc_bearers and media_list arrays to fix an
obvious simmilar problem that arises from issuing tipc-config commands to
manipulate bearers/links prior to entering networked mode
I've tested this for a few hours by running the sanity tests and stress test
with the tipcutils suite, and nothing has fallen over. There have been a few
lockdep warnings, but those were there before, and can be addressed later, as
they didn't actually result in any deadlock.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Allan Stephens <allan.stephens@windriver.com> CC: David S. Miller <davem@davemloft.net> CC: tipc-discussion@lists.sourceforge.net
bearer.c | 37 ++++++-------------------------------
bearer.h | 2 +-
net.c | 25 ++++---------------------
3 files changed, 11 insertions(+), 53 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Wed, 3 Mar 2010 04:01:13 +0000 (04:01 +0000)]
gre: fix hard header destination address checking
ipgre_header() can be called with zero daddr when the gre device is
configured as multipoint tunnel and still has the NOARP flag set (which is
typically cleared by the userspace arp daemon). If the NOARP packets are
not dropped, ipgre_tunnel_xmit() will take rt->rt_gateway (= NBMA IP) and
use that for route look up (and may lead to bogus xfrm acquires).
The multicast address check is removed as sending to multicast group should
be ok. In fact, if gre device has a multicast address as destination
ipgre_header is always called with multicast address.
Signed-off-by: Timo Teras <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: fix race between cleanup and add/delete address
This solves a potential race problem during the cleanup process.
The issue is that addrconf_ifdown() needs to traverse address list,
but then drop lock to call the notifier. The version in -next
could get confused if add/delete happened during this window.
Original code (2.6.32 and earlier) was okay because all addresses
were always deleted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
My recent change in net-next to retain permanent addresses caused regression.
Device refcount would not go to zero when device was unregistered because
left over anycast reference would hold ipv6 dev reference which would hold
device references...
The correct procedure is to call notify chain when address is no longer
available for use. When interface comes back DAD timer will notify
back that address is available.
Also, link local addresses should be purged when interface is brought
down. The address might be changed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Router Solicitation timer races with device state changes
because it doesn't lock the device. Use local variable to avoid
one repeated dereference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timer code runs in bottom half, so there is no need for
using _bh form of locking. Also check if device is not ready
to avoid race with address that is no longer active.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut Schaa [Wed, 3 Mar 2010 16:42:55 +0000 (17:42 +0100)]
rt2x00: Export rt2x00soc_probe from rt2x00soc
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 1 Mar 2010 09:12:57 +0000 (14:42 +0530)]
mac80211: Fix HT rate control configuration
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Tue, 2 Mar 2010 15:48:23 +0000 (15:48 +0000)]
Bluetooth: Use single_open() for inquiry cache within debugfs
The inquiry cache information in debugfs should be using seq_file support
and not allocating memory on the stack for the string. Since the usage of
these information is really seldom, using single_open() for it is good
enough.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 2 Mar 2010 20:40:01 +0000 (20:40 +0000)]
af_packet: move strict addr_len check right before dev_[mc/unicast]_[add/del]
My previous patch 914c8ad2d18b62ad1420f518c0cab0b0b90ab308 incorrectly changed
the length check in packet_mc_add to be more strict. The problem is that
userspace is not filling this field (and it stays zeroed) in case of setting
PACKET_MR_PROMISC or PACKET_MR_ALLMULTI. So move the strict check to the point
in path where the addr_len must be set correctly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 2 Mar 2010 02:51:56 +0000 (02:51 +0000)]
ipsec: Fix bogus bundle flowi
When I merged the bundle creation code, I introduced a bogus
flowi value in the bundle. Instead of getting from the caller,
it was instead set to the flow in the route object, which is
totally different.
The end result is that the bundles we created never match, and
we instead end up with an ever growing bundle list.
Thanks to Jamal for find this problem.
Reported-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 29 Jan 2010 19:54:56 +0000 (11:54 -0800)]
iwlwifi: load firmware asynchronously before mac80211 registration
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:30 +0000 (13:15 +0100)]
ar9170: load firmware asynchronously
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bryan Polk [Mon, 1 Mar 2010 17:23:28 +0000 (12:23 -0500)]
rt2x00: Add USB ID for CEIVA adapter to rt73usb
This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: Bryan Polk <sainth@eidolons.org> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.
This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: Jouni Malinen <j@w1.fi> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 27 Feb 2010 06:12:34 +0000 (09:12 +0300)]
zd1211rw: fix potential array underflow
The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow. I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matthew Garrett [Tue, 16 Feb 2010 21:36:25 +0000 (16:36 -0500)]
rfkill: Add support for KEY_RFKILL
Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Tue, 2 Mar 2010 18:34:25 +0000 (10:34 -0800)]
Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Support show_unhandled_signals.
sparc: use __ratelimit
sunxvr500: Additional PCI id for sunxvr500 driver
sparc: use asm-generic/scatterlist.h
sparc64: If 'slot-names' property exist, create sysfs PCI slot information.
sparc: remove trailing space in messages
sparc: remove redundant return statements
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
Jiri Pirko [Tue, 2 Mar 2010 11:57:33 +0000 (03:57 -0800)]
virtio_net: remove forgotten assignment
This is no longer needed. I missed to remove this in 567ec874d15b478c8eda7e9a5d2dcb05f13f1fb5 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Tue, 2 Mar 2010 11:56:39 +0000 (03:56 -0800)]
be2net: fix tx completion polling
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 1 Mar 2010 03:09:26 +0000 (03:09 +0000)]
net: fix protocol sk_buff field
Commit e992cd9b72a18 (kmemcheck: make bitfield annotations truly no-ops
when disabled) allows us to revert a workaround we did in the past to
not add holes in sk_buff structure.
This patch partially reverts commit 14d18a81b5171
(net: fix kmemcheck annotations) so that sparse doesnt complain:
include/linux/skbuff.h:357:41: error: invalid bitfield specifier for
type restricted __be16.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: Fix build error when IGMP_SNOOPING is not enabled
Fix the following build error when IGMP_SNOOPING is not enabled.
In file included from net/bridge/br.c:24:
net/bridge/br_private.h: In function 'br_multicast_is_router':
net/bridge/br_private.h:361: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:362: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:363: error: 'struct net_bridge' has no member named 'multicast_router_timer'
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 1 Mar 2010 21:05:40 +0000 (13:05 -0800)]
Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
Linus Torvalds [Mon, 1 Mar 2010 21:04:58 +0000 (13:04 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
sata_via: Delay on vt6420 when starting ATAPI DMA write
ata: Detect Delkin Devices compact flash
pata_efar: Enable parallel scanning
pata_atiixp: enable parallel scan
[libata] pata_atiixp: add locking for parallel scanning
[libata] pata_efar: add locking for parallel scanning
libata: Pass host flags into the pci helper
[libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
libata: Allow pata_legacy to be built on non-ISA but PCI systems
pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
[libata] pata_at91: fix backslash-continued string
pata_via: store UDMA masks in via_isa_bridges table
pata_via: fix address setup timings underlocking
pata_serverworks: fix error message
pata_serverworks: fix PIO setup for the second channel
pata_efar: fix secondary port support
pata_cypress: fix PIO timings underclocking
pata_cs5535: use correct values for PIO1 and PIO2 data timings
pata_cmd64x: remove unused definitions
...
Bart Hartgers [Sun, 14 Feb 2010 12:04:50 +0000 (13:04 +0100)]
sata_via: Delay on vt6420 when starting ATAPI DMA write
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.
I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.
There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Gardner [Tue, 23 Feb 2010 18:41:22 +0000 (12:41 -0600)]
ata: Detect Delkin Devices compact flash
I have a Delkin Devices compact flash card that isn't being recognized using the
SATA/PATA drivers.
The card is recognized and works with the deprecated ATA drivers.
The error I am seeing is:
ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0)
I tracked it down to ata_id_is_cfa() in include/linux/ata.h.
The Delkin card has id[0] set to 0x844a and id[83] set to 0.
This isn't what the kernel expects and is probably incorrect.
The simplest work-around is to add a check for 0x844a to ata_id_is_cfa().
Signed-off-by: Ben Gardner <gardner.ben@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / mirror_ubuntu-kernels.git / log