Eric Dumazet [Tue, 20 Nov 2018 13:53:59 +0000 (05:53 -0800)]
tcp: defer SACK compression after DupThresh
Jean-Louis reported a TCP regression and bisected to recent SACK
compression.
After a loss episode (receiver not able to keep up and dropping
packets because its backlog is full), linux TCP stack is sending
a single SACK (DUPACK).
Sender waits a full RTO timer before recovering losses.
While RFC 6675 says in section 5, "Algorithm Details",
(2) If DupAcks < DupThresh but IsLost (HighACK + 1) returns true --
indicating at least three segments have arrived above the current
cumulative acknowledgment point, which is taken to indicate loss
-- go to step (4).
...
(4) Invoke fast retransmit and enter loss recovery as follows:
there are old TCP stacks not implementing this strategy, and
still counting the dupacks before starting fast retransmit.
While these stacks probably perform poorly when receivers implement
LRO/GRO, we should be a little more gentle to them.
This patch makes sure we do not enable SACK compression unless
3 dupacks have been sent since last rcv_nxt update.
Ideally we should even rearm the timer to send one or two
more DUPACK if no more packets are coming, but that will
be work aiming for linux-4.21.
Many thanks to Jean-Louis for bisecting the issue, providing
packet captures and testing this patch.
Fixes: 5d9f4262b7ea ("tcp: add SACK compression") Reported-by: Jean-Louis Dupond <jean-louis@dupond.be> Tested-by: Jean-Louis Dupond <jean-louis@dupond.be> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 20 Nov 2018 11:39:56 +0000 (11:39 +0000)]
net: skb_scrub_packet(): Scrub offload_fwd_mark
When a packet is trapped and the corresponding SKB marked as
already-forwarded, it retains this marking even after it is forwarded
across veth links into another bridge. There, since it ingresses the
bridge over veth, which doesn't have offload_fwd_mark, it triggers a
warning in nbp_switchdev_frame_mark().
Then nbp_switchdev_allowed_egress() decides not to allow egress from
this bridge through another veth, because the SKB is already marked, and
the mark (of 0) of course matches. Thus the packet is incorrectly
blocked.
Solve by resetting offload_fwd_mark() in skb_scrub_packet(). That
function is called from tunnels and also from veth, and thus catches the
cases where traffic is forwarded between bridges and transformed in a
way that invalidates the marking.
Fixes: 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for stacked devices") Fixes: abf4bb6b63d0 ("skbuff: Add the offload_mr_fwd_mark field") Signed-off-by: Petr Machata <petrm@mellanox.com> Suggested-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Tue, 20 Nov 2018 21:18:44 +0000 (22:18 +0100)]
net/sched: act_police: fix race condition on state variables
after 'police' configuration parameters were converted to use RCU instead
of spinlock, the state variables used to compute the traffic rate (namely
'tcfp_toks', 'tcfp_ptoks' and 'tcfp_t_c') are erroneously read/updated in
the traffic path without any protection.
Use a dedicated spinlock to avoid race conditions on these variables, and
ensure proper cache-line alignment. In this way, 'police' is still faster
than what we observed when 'tcf_lock' was used in the traffic path _ i.e.
reverting commit 2d550dbad83c ("net/sched: act_police: don't use spinlock
in the data path"). Moreover, we preserve the throughput improvement that
was obtained after 'police' started using per-cpu counters, when 'avrate'
is used instead of 'rate'.
Changes since v1 (thanks to Eric Dumazet):
- call ktime_get_ns() before acquiring the lock in the traffic path
- use a dedicated spinlock instead of tcf_lock
- improve cache-line usage
Fixes: 2d550dbad83c ("net/sched: act_police: don't use spinlock in the data path") Reported-and-suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com>
Heiner Kallweit [Tue, 20 Nov 2018 20:22:50 +0000 (21:22 +0100)]
MAINTAINERS: add myself as co-maintainer for r8169
Meanwhile I know the driver quite well and I refactored bigger parts
of it. As a result people contact me already with r8169 questions.
Therefore I'd volunteer to become co-maintainer of the driver also
officially.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Mallon [Tue, 20 Nov 2018 08:15:02 +0000 (19:15 +1100)]
tcp: Fix SOF_TIMESTAMPING_RX_HARDWARE to use the latest timestamp during TCP coalescing
During tcp coalescing ensure that the skb hardware timestamp refers to the
highest sequence number data.
Previously only the software timestamp was updated during coalescing.
Signed-off-by: Stephen Mallon <stephen.mallon@sydney.edu.au> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Add PHY reset for 5717/5719/5720 in change ring and flow control paths
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following fixes are for mlx5 core and netdev driver.
For -stable v4.16 bc7fda7d4637 ('net/mlx5e: IPoIB, Reset QP after channels are closed')
For -stable v4.17 36917a270395 ('net/mlx5: IPSec, Fix the SA context hash key')
For -stable v4.18 6492a432be3a ('net/mlx5e: Always use the match level enum when parsing TC rule match') c3f81be236b1 ('net/mlx5e: Removed unnecessary warnings in FEC caps query') c5ce2e736b64 ('net/mlx5e: Fix selftest for small MTUs')
For -stable v4.19 effcd896b25e ('net/mlx5e: Adjust to max number of channles when re-attaching') 394cbc5acd68 ('net/mlx5e: RX, verify received packet size in Linear Striding RQ') 447cbb3613c8 ('net/mlx5e: Don't match on vlan non-existence if ethertype is wildcarded') c223c1574612 ('net/mlx5e: Claim TC hw offloads support only under a proper build config')
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Juliet Kim [Mon, 19 Nov 2018 21:59:22 +0000 (15:59 -0600)]
net/ibmnvic: Fix deadlock problem in reset
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series fixes various queue manager getter functions. It is
important to make sure the getter's caller will receive a valid queue even
in error case to prevent more serious bugs.
Please consider applying to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Mon, 19 Nov 2018 14:28:31 +0000 (16:28 +0200)]
qed: Fix QM getters to always return a valid pq
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration") Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Mon, 19 Nov 2018 14:28:30 +0000 (16:28 +0200)]
qed: Fix bitmap_weight() check
Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration") Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shay Agroskin [Thu, 8 Nov 2018 12:23:36 +0000 (14:23 +0200)]
net/mlx5e: Fix failing ethtool query on FEC query error
If FEC caps query fails when executing 'ethtool <interface>'
the whole callback fails unnecessarily, fixed that by replacing the
error return code with debug logging only.
Shay Agroskin [Sun, 28 Oct 2018 07:06:11 +0000 (09:06 +0200)]
net/mlx5e: Removed unnecessary warnings in FEC caps query
Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.
Shay Agroskin [Sun, 28 Oct 2018 14:13:46 +0000 (16:13 +0200)]
net/mlx5e: Fix a bug in turning off FEC policy in unsupported speeds
Some speeds don't support turning FEC policy off. In case a requested
FEC policy is not supported for a speed (including current speed), its new
FEC policy would be:
no FEC - if disabling FEC is supported for that speed
unchanged - else
====================
net: ena: hibernation and rmmod bug fixes
This patchset includes 2 bug fixes:
1. A fix to a crash during resume from hibernation.
2. A fix to an illegal memory access during driver removal (e.g. during rmmod)
which might cause a crash in certain systems.
The subminor number in the driver version is also promoted to indicate driver
was changed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ena_remove() we have the following stack call:
ena_remove()
unregister_netdev()
ena_destroy_device()
netif_carrier_off()
Calling netif_carrier_off() causes linkwatch to try to handle the
link change event on the already unregistered netdev, which leads
to a read from an unreadable memory address.
This patch switches the order of the two functions, so that
netif_carrier_off() is called on a regiestered netdev.
To accomplish this fix we also had to:
1. Remove the set bit ENA_FLAG_TRIGGER_RESET
2. Add a sanitiy check in ena_close()
both to prevent double device reset (when calling unregister_netdev()
ena_close is called, but the device was already deleted in
ena_destroy_device()).
3. Set the admin_queue running state to false to avoid using it after
device was reset (for example when calling ena_destroy_all_io_queues()
right after ena_com_dev_reset() in ena_down)
Fixes: 944b28aa2982 ("net: ena: fix missing lock during device destruction") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ena: fix crash during failed resume from hibernation
During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.
In this commit we switch the call order of the above two functions
to avoid this crash.
Fixes: d7703ddbd7c9 ("net: ena: fix rare bug when failed restart/resume is followed by driver removal") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 13:59:49 +0000 (21:59 +0800)]
sctp: not increase stream's incnt before sending addstrm_in request
Different from processing the addstrm_out request, The receiver handles
an addstrm_in request by sending back an addstrm_out request to the
sender who will increase its stream's in and incnt later.
Now stream->incnt has been increased since it sent out the addstrm_in
request in sctp_send_add_streams(), with the wrong stream->incnt will
even cause crash when copying stream info from the old stream's in to
the new one's in sctp_process_strreset_addstrm_out().
This patch is to fix it by simply removing the stream->incnt change
from sctp_send_add_streams().
Fixes: 242bd2d519d7 ("sctp: implement sender-side procedures for Add Incoming/Outgoing Streams Request Parameter") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Valentine Fatiev [Wed, 17 Oct 2018 08:45:07 +0000 (11:45 +0300)]
net/mlx5e: Fix selftest for small MTUs
Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.
Fixes: d605d66 ("net/mlx5e: Add support for ethtool self diagnostics test") Signed-off-by: Valentine Fatiev <valentinef@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Moshe Shemesh [Thu, 11 Oct 2018 04:31:10 +0000 (07:31 +0300)]
net/mlx5e: RX, verify received packet size in Linear Striding RQ
In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU. In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.
Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.
As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).
Fixes: 619a8f2a42f1 ("net/mlx5e: Use linear SKB in Striding RQ") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Tue, 23 Oct 2018 14:30:04 +0000 (17:30 +0300)]
net/mlx5e: Apply the correct check for supporting TC esw rules split
The mirror and not the output count is the one denoting a split.
Fix to condition the offload attempt on the mirror count being > 0
along the firmware to have the related capability.
Fixes: 592d36515969 ("net/mlx5e: Parse mirroring action for offloaded TC eswitch flows") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Yossi Kuperman <yossiku@mellanox.com> Reviewed-by: Chris Mi <chrism@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Yuval Avnery [Tue, 16 Oct 2018 20:20:20 +0000 (15:20 -0500)]
net/mlx5e: Adjust to max number of channles when re-attaching
When core driver enters deattach/attach flow after pci reset,
Number of logical CPUs may have changed.
As a result we need to update the cpu affiliated resource tables.
1. indirect rqt list
2. eq table
Reproduction (PowerPC):
echo 1000 > /sys/kernel/debug/powerpc/eeh_max_freezes
ppc64_cpu --smt=on
# Restart driver
modprobe -r ... ; modprobe ...
# Link up
ifconfig ...
# Only physical CPUs
ppc64_cpu --smt=off
# Inject PCI errors so PCI will reset - calling the pci error handler
echo 0x8000000000000000 > /sys/kernel/debug/powerpc/<PCI BUS>/err_injct_inboundA
Call trace when trying to add non-existing rqs to an indirect rqt:
mlx5e_redirect_rqt+0x84/0x260 [mlx5_core] (unreliable)
mlx5e_redirect_rqts+0x188/0x190 [mlx5_core]
mlx5e_activate_priv_channels+0x488/0x570 [mlx5_core]
mlx5e_open_locked+0xbc/0x140 [mlx5_core]
mlx5e_open+0x50/0x130 [mlx5_core]
mlx5e_nic_enable+0x174/0x1b0 [mlx5_core]
mlx5e_attach_netdev+0x154/0x290 [mlx5_core]
mlx5e_attach+0x88/0xd0 [mlx5_core]
mlx5_attach_device+0x168/0x1e0 [mlx5_core]
mlx5_load_one+0x1140/0x1210 [mlx5_core]
mlx5_pci_resume+0x6c/0xf0 [mlx5_core]
Create cq will fail when trying to use non-existing EQ.
Or Gerlitz [Sun, 28 Oct 2018 10:27:29 +0000 (12:27 +0200)]
net/mlx5e: Always use the match level enum when parsing TC rule match
We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.
This worked accidentally b/c both enums have the same numerical values.
Fixes: d708f902989b ('net/mlx5e: Get the required HW match level while parsing TC flow matches') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Thu, 18 Oct 2018 10:31:27 +0000 (12:31 +0200)]
net/mlx5e: Claim TC hw offloads support only under a proper build config
Currently, we are only supporting tc hw offloads when the eswitch
support is compiled in, but we are not gating the adevertizment
of the NETIF_F_HW_TC feature on this config being set.
Fix it, and while doing that, also avoid dealing with the feature
on ethtool when the config is not set.
Fixes: e8f887ac6a45 ('net/mlx5e: Introduce tc offload support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Thu, 25 Oct 2018 15:41:58 +0000 (15:41 +0000)]
net/mlx5e: Don't match on vlan non-existence if ethertype is wildcarded
For the "all" ethertype we should not care whether the packet has
vlans. Besides being wrong, the way we did it caused FW error
for rules such as:
tc filter add dev eth0 protocol all parent ffff: \
prio 1 flower skip_sw action drop
b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec)
wasn't set. Fix that by matching on vlan non-existence only if we were
also told to match on the ethertype.
Fixes: cee26487620b ('net/mlx5e: Set vlan masks for all offloaded TC rules') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com> Reviewed-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5e: IPoIB, Reset QP after channels are closed
The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.
The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.
Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.
Fixes: dae37456c8ac ("net/mlx5: Support for attaching multiple underlay QPs to root flow table") Signed-off-by: Denis Drozdov <denisd@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Raed Salem [Thu, 18 Oct 2018 05:55:21 +0000 (08:55 +0300)]
net/mlx5: IPSec, Fix the SA context hash key
The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.
This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.
The dst's mtu in transport can be updated by a non sctp place like
in xfrm where the MTU information didn't get synced between asoc,
transport and dst, so it is still needed to do the pmtu check
in sctp_packet_config.
Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 07:21:53 +0000 (15:21 +0800)]
sctp: not allow to set asoc prsctp_enable by sockopt
As rfc7496#section4.5 says about SCTP_PR_SUPPORTED:
This socket option allows the enabling or disabling of the
negotiation of PR-SCTP support for future associations. For existing
associations, it allows one to query whether or not PR-SCTP support
was negotiated on a particular association.
It means only sctp sock's prsctp_enable can be set.
Note that for the limitation of SCTP_{CURRENT|ALL}_ASSOC, we will
add it when introducing SCTP_{FUTURE|CURRENT|ALL}_ASSOC for linux
sctp in another patchset.
v1->v2:
- drop the params.assoc_id check as Neil suggested.
Fixes: 28aa4c26fce2 ("sctp: add SCTP_PR_SUPPORTED on sctp sockopt") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 07:07:38 +0000 (15:07 +0800)]
sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmit
Now sctp increases sk_wmem_alloc by 1 when doing set_owner_w for the
skb allocked in sctp_packet_transmit and decreases by 1 when freeing
this skb.
But when this skb goes through networking stack, some subcomponents
might change skb->truesize and add the same amount on sk_wmem_alloc.
However sctp doesn't know the amount to decrease by, it would cause
a leak on sk->sk_wmem_alloc and the sock can never be freed.
Xiumei found this issue when it hit esp_output_head() by using sctp
over ipsec, where skb->truesize is added and so is sk->sk_wmem_alloc.
Since sctp has used sk_wmem_queued to count for writable space since
Commit cd305c74b0f8 ("sctp: use sk_wmem_queued to check for writable
space"), it's ok to fix it by counting sk_wmem_alloc by skb truesize
in sctp_packet_transmit.
Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 07:01:03 +0000 (08:01 +0100)]
MAINTAINERS: Add myself as third phylib maintainer
Add myself as third phylib maintainer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
Matthew Cover [Sun, 18 Nov 2018 07:46:00 +0000 (00:46 -0700)]
tuntap: fix multiqueue rx
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 18 Nov 2018 18:45:30 +0000 (10:45 -0800)]
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack") Reported-by: Preethi Ramachandra <preethir@juniper.net> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Nov 2018 20:21:09 +0000 (12:21 -0800)]
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Linus Torvalds [Sun, 18 Nov 2018 19:31:26 +0000 (11:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
mm, page_alloc: check for max order in hot path
scripts/spdxcheck.py: make python3 compliant
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
mm/vmstat.c: fix NUMA statistics updates
mm/gup.c: fix follow_page_mask() kerneldoc comment
ocfs2: free up write context when direct IO failed
scripts/faddr2line: fix location of start_kernel in comment
mm: don't reclaim inodes with many attached pages
mm, memory_hotplug: check zone_movable in has_unmovable_pages
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
MAINTAINERS: update OMAP MMC entry
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
kernel/sched/psi.c: simplify cgroup_move_task()
z3fold: fix possible reclaim races
Linus Torvalds [Sun, 18 Nov 2018 18:58:20 +0000 (10:58 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix an exec() related scalability/performance regression, which was
caused by incorrectly calculating load and migrating tasks on exec()
when they shouldn't be"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix cpu_util_wake() for 'execl' type workloads
Linus Torvalds [Sun, 18 Nov 2018 18:54:59 +0000 (10:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix uncore PMU enumeration for CofeeLake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Support CoffeeLake 8th CBOX
perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs
Linus Torvalds [Sun, 18 Nov 2018 18:52:26 +0000 (10:52 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc fixes: two warning splat fixes, a leak fix and persistent memory
allocation fixes for ARM"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Permit calling efi_mem_reserve_persistent() from atomic context
efi/arm: Defer persistent reservations until after paging_init()
efi/arm/libstub: Pack FDT after populating it
efi/arm: Revert deferred unmap of early memmap mapping
efi: Fix debugobjects warning on 'efi_rts_work'
Linus Torvalds [Sun, 18 Nov 2018 18:45:09 +0000 (10:45 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM spectre updates from Russell King:
"These are the currently known final bits that resolve the Spectre
issues. big.Little systems used to be sufficiently identical in that
there were no differences between individual CPUs in the system that
mattered to the kernel. With the advent of the Spectre problem, the
CPUs now have differences in how the workaround is applied.
As a result of previous Spectre patches, these systems ended up
reporting quite a lot of:
"CPUx: Spectre v2: incorrect context switching function, system vulnerable"
messages due to the action of the big.Little switcher causing the CPUs
to be re-initialised regularly. This series resolves that issue by
making the CPU vtable unique to each CPU.
However, since this is used very early, before per-cpu is setup,
per-cpu can't be used. We also have a problem that two of the methods
are not called from preempt-safe paths, but thankfully these remain
identical between all CPUs in the system. To make sure, we validate
that these are identical during boot"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: spectre-v2: per-CPU vtables to work around big.Little systems
ARM: add PROC_VTABLE and PROC_TABLE macros
ARM: clean up per-processor check_bugs method call
ARM: split out processor lookup
ARM: make lookup_processor_type() non-__init
the problem is that we only check for an out of bound order in the slow
path and the node reclaim might happen from the fast path already. This
is fixable by making sure that kvmalloc doesn't ever use kmalloc for
requests that are larger than KMALLOC_MAX_SIZE but this also shows that
the code is rather fragile. A recent UBSAN report just underlines that
by the following report
Note that this is not a kvmalloc path. It is just that the fast path
really depends on having sanitzed order as well. Therefore move the
order check to the fast path.
Link: http://lkml.kernel.org/r/20181113094305.GM15120@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by: Kyungtae Kim <kt0755@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Pavel Tatashin <pavel.tatashin@microsoft.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Aaron Lu <aaron.lu@intel.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Byoungyoung Lee <lifeasageek@gmail.com> Cc: "Dae R. Jeong" <threeearcat@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this change the following happens when using Python3 (3.6.6):
$ echo "GPL-2.0" | python3 scripts/spdxcheck.py -
FAIL: 'str' object has no attribute 'decode'
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 253, in <module>
parser.parse_lines(sys.stdin, args.maxlines, '-')
File "scripts/spdxcheck.py", line 171, in parse_lines
line = line.decode(locale.getpreferredencoding(False), errors='ignore')
AttributeError: 'str' object has no attribute 'decode'
So as the line is already a string, there is no need to decode it and
the line can be dropped.
/usr/bin/python on Arch is Python 3. So this would indeed be worth
going into 4.19.
Link: http://lkml.kernel.org/r/20181023070802.22558-1-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Joe Perches <joe@perches.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yufen Yu [Fri, 16 Nov 2018 23:08:39 +0000 (15:08 -0800)]
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
Other filesystems such as ext4, f2fs and ubifs all return ENXIO when
lseek (SEEK_DATA or SEEK_HOLE) requests a negative offset.
man 2 lseek says
: EINVAL whence is not valid. Or: the resulting file offset would be
: negative, or beyond the end of a seekable device.
:
: ENXIO whence is SEEK_DATA or SEEK_HOLE, and the file offset is beyond
: the end of the file.
Make tmpfs return ENXIO under these circumstances as well. After this,
tmpfs also passes xfstests's generic/448.
[akpm@linux-foundation.org: rewrite changelog] Link: http://lkml.kernel.org/r/1540434176-14349-1-git-send-email-yuyufen@huawei.com Signed-off-by: Yufen Yu <yuyufen@huawei.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 16 Nov 2018 23:08:35 +0000 (15:08 -0800)]
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
gcc-8 complains about the prototype for this function:
lib/ubsan.c:432:1: error: ignoring attribute 'noreturn' in declaration of a built-in function '__ubsan_handle_builtin_unreachable' because it conflicts with attribute 'const' [-Werror=attributes]
This is actually a GCC's bug. In GCC internals
__ubsan_handle_builtin_unreachable() declared with both 'noreturn' and
'const' attributes instead of only 'noreturn':
Janne Huttunen [Fri, 16 Nov 2018 23:08:32 +0000 (15:08 -0800)]
mm/vmstat.c: fix NUMA statistics updates
Scan through the whole array to see if an update is needed. While we're
at it, use sizeof() to be safe against any possible type changes in the
future.
The bug here is that we wouldn't sync per-cpu counters into global ones
if there was an update of numa_stats for higher cpus. Highly
theoretical one though because it is much more probable that zone_stats
are updated so we would refresh anyway. So I wouldn't bother to mark
this for stable, yet something nice to fix.
[mhocko@suse.com: changelog enhancement] Link: http://lkml.kernel.org/r/1541601517-17282-1-git-send-email-janne.huttunen@nokia.com Fixes: 1d90ca897cb0 ("mm: update NUMA counter threshold size") Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit df06b37ffe5a ("mm/gup: cache dev_pagemap while pinning pages")
modified the signature of follow_page_mask() but left the parameter
description behind.
Update the description to make the code and comments agree again.
While at it, update formatting of the return value description to match
Documentation/doc-guide/kernel-doc.rst guidelines.
Wengang Wang [Fri, 16 Nov 2018 23:08:25 +0000 (15:08 -0800)]
ocfs2: free up write context when direct IO failed
The write context should also be freed even when direct IO failed.
Otherwise a memory leak is introduced and entries remain in
oi->ip_unwritten_list causing the following BUG later in unlink path:
Roman Gushchin [Fri, 16 Nov 2018 23:08:18 +0000 (15:08 -0800)]
mm: don't reclaim inodes with many attached pages
Spock reported that commit 172b06c32b94 ("mm: slowly shrink slabs with a
relatively small number of objects") leads to a regression on his setup:
periodically the majority of the pagecache is evicted without an obvious
reason, while before the change the amount of free memory was balancing
around the watermark.
The reason behind is that the mentioned above change created some
minimal background pressure on the inode cache. The problem is that if
an inode is considered to be reclaimed, all belonging pagecache page are
stripped, no matter how many of them are there. So, if a huge
multi-gigabyte file is cached in the memory, and the goal is to reclaim
only few slab objects (unused inodes), we still can eventually evict all
gigabytes of the pagecache at once.
The workload described by Spock has few large non-mapped files in the
pagecache, so it's especially noticeable.
To solve the problem let's postpone the reclaim of inodes, which have
more than 1 attached page. Let's wait until the pagecache pages will be
evicted naturally by scanning the corresponding LRU lists, and only then
reclaim the inode structure.
Link: http://lkml.kernel.org/r/20181023164302.20436-1-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Reported-by: Spock <dairinin@gmail.com> Tested-by: Spock <dairinin@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Rik van Riel <riel@surriel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> [4.19.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:15 +0000 (15:08 -0800)]
mm, memory_hotplug: check zone_movable in has_unmovable_pages
Page state checks are racy. Under a heavy memory workload (e.g. stress
-m 200 -t 2h) it is quite easy to hit a race window when the page is
allocated but its state is not fully populated yet. A debugging patch to
dump the struct page state shows
Note that the state has been checked for both PageLRU and PageSwapBacked
already. Closing this race completely would require some sort of retry
logic. This can be tricky and error prone (think of potential endless
or long taking loops).
Workaround this problem for movable zones at least. Such a zone should
only contain movable pages. Commit 15c30bc09085 ("mm, memory_hotplug:
make has_unmovable_pages more robust") has told us that this is not
strictly true though. Bootmem pages should be marked reserved though so
we can move the original check after the PageReserved check. Pages from
other zones are still prone to races but we even do not pretend that
memory hotremove works for those so pre-mature failure doesn't hurt that
much.
Link: http://lkml.kernel.org/r/20181106095524.14629-1-mhocko@kernel.org Fixes: 15c30bc09085 ("mm, memory_hotplug: make has_unmovable_pages more robust") Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Baoquan He <bhe@redhat.com> Tested-by: Baoquan He <bhe@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Fri, 16 Nov 2018 23:08:11 +0000 (15:08 -0800)]
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
Commit a2468cc9bfdf ("swap: choose swap device according to numa node")
changed 'avail_lists' field of 'struct swap_info_struct' to an array.
In popular linux distros it increased size of swap_info_struct up to 40
Kbytes and now swap_info_struct allocation requires order-4 page.
Switch to kvzmalloc allows to avoid unexpected allocation failures.
Link: http://lkml.kernel.org/r/fc23172d-3c75-21e2-d551-8b1808cbe593@virtuozzo.com Fixes: a2468cc9bfdf ("swap: choose swap device according to numa node") Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Acked-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Huang Ying <ying.huang@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Fri, 16 Nov 2018 23:08:08 +0000 (15:08 -0800)]
MAINTAINERS: update OMAP MMC entry
Jarkko's e-mail address hasn't worked for a long time. We still want to
keep this driver working as it is critical for some of the OMAP boards.
I use and test this driver frequently, so change myself as a maintainer
with "Odd Fixes" status.
Link: http://lkml.kernel.org/r/20181106222750.12939-1-aaro.koskinen@iki.fi Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 16 Nov 2018 23:08:04 +0000 (15:08 -0800)]
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
This bug has been experienced several times by the Oracle DB team. The
BUG is in remove_inode_hugepages() as follows:
/*
* If page is mapped, it was faulted in after being
* unmapped in caller. Unmap (again) now after taking
* the fault mutex. The mutex will prevent faults
* until we finish removing the page.
*
* This race can only happen in the hole punch case.
* Getting here in a truncate operation is a bug.
*/
if (unlikely(page_mapped(page))) {
BUG_ON(truncate_op);
In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code. Consider the following:
- Process A maps a hugetlbfs file of sufficient size and alignment
(PUD_SIZE) that a pmd page could be shared.
- Process B maps the same hugetlbfs file with the same size and
alignment such that a pmd page is shared.
- Process B then calls mprotect() to change protections for the mapping
with the shared pmd. As a result, the pmd is 'unshared'.
- Process B then calls mprotect() again to chage protections for the
mapping back to their original value. pmd remains unshared.
- Process B then forks and process C is created. During the fork
process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
tables. Copying page tables for hugetlb mappings is done in the
routine copy_hugetlb_page_range.
In copy_hugetlb_page_range(), the destination pte is obtained by:
dst_pte = huge_pte_alloc(dst, addr, sz);
If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table. In the situation above, process C could share with
either process A or process B. Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.
However, the check for pmd sharing in copy_hugetlb_page_range is:
/* If the pagetables are shared don't copy or take references */
if (dst_pte == src_pte)
continue;
Since process C is sharing with process A instead of process B, the
above test fails. The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte. It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page. This is how we end up with an elevated map count.
To solve, check the dst_pte entry for huge_pte_none. If !none, this
implies PMD sharing so do not copy.
Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com Fixes: c5c99429fa57 ("fix hugepages leak due to pagetable page sharing") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 16 Nov 2018 23:08:00 +0000 (15:08 -0800)]
kernel/sched/psi.c: simplify cgroup_move_task()
The existing code triggered an invalid warning about 'rq' possibly being
used uninitialized. Instead of doing the silly warning suppression by
initializa it to NULL, refactor the code to bail out early instead.
Warning was:
kernel/sched/psi.c: In function `cgroup_move_task':
kernel/sched/psi.c:639:13: warning: `rq' may be used uninitialized in this function [-Wmaybe-uninitialized]
Link: http://lkml.kernel.org/r/20181103183339.8669-1-olof@lixom.net Fixes: 2ce7135adc9ad ("psi: cgroup support") Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Wool [Fri, 16 Nov 2018 23:07:56 +0000 (15:07 -0800)]
z3fold: fix possible reclaim races
Reclaim and free can race on an object which is basically fine but in
order for reclaim to be able to map "freed" object we need to encode
object length in the handle. handle_to_chunks() is then introduced to
extract object length from a handle and use it during mapping.
Moreover, to avoid racing on a z3fold "headless" page release, we should
not try to free that page in z3fold_free() if the reclaim bit is set.
Also, in the unlikely case of trying to reclaim a page being freed, we
should not proceed with that page.
While at it, fix the page accounting in reclaim function.
This patch supersedes "[PATCH] z3fold: fix reclaim lock-ups".
Link: http://lkml.kernel.org/r/20181105162225.74e8837d03583a9b707cf559@gmail.com Signed-off-by: Vitaly Wool <vitaly.vul@sony.com> Signed-off-by: Jongseok Kim <ks77sj@gmail.com> Reported-by-by: Jongseok Kim <ks77sj@gmail.com> Reviewed-by: Snild Dolkow <snild@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jon Maloy [Sat, 17 Nov 2018 17:17:06 +0000 (12:17 -0500)]
tipc: don't assume linear buffer when reading ancillary data
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason seems to be that tipc_net_finalize()->tipc_sk_reinit() is
calling the function rhashtable_walk_enter() within a timer interrupt.
We fix this by executing tipc_net_finalize() in work queue context.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 18 Nov 2018 05:57:02 +0000 (21:57 -0800)]
net-gro: reset skb->pkt_type in napi_reuse_skb()
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab2033 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab2033 ("gro: Add internal interfaces for VLAN") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 18 Nov 2018 05:54:53 +0000 (21:54 -0800)]
Merge branch 'tdc-fixes'
Lucas Bates says:
====================
Prevent uncaught exceptions in tdc
This patch series addresses two potential bugs in tdc that can
cause exceptions to be raised in certain circumstances. These
exceptions are generally not handled, so instead we will prevent
them from being raised.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Brenda J. Butler [Fri, 16 Nov 2018 22:37:56 +0000 (17:37 -0500)]
tc-testing: tdc.py: Guard against lack of returncode in executed command
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com> Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates [Fri, 16 Nov 2018 22:37:55 +0000 (17:37 -0500)]
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 16 Nov 2018 15:58:19 +0000 (16:58 +0100)]
ip_tunnel: don't force DF when MTU is locked
The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We would like the existing community to be kept in the loop for any new
developments on CAKE; and I certainly plan to keep maintaining it. Reflect
this in MAINTAINERS.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix vlan stats use-after-free on destruction
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f0c ("net: bridge: add support for per-port vlan stats") Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Slavomir Kaslev [Fri, 16 Nov 2018 09:27:53 +0000 (11:27 +0200)]
socket: do a generic_file_splice_read when proto_ops has no splice_read
splice(2) fails with -EINVAL when called reading on a socket with no splice_read
set in its proto_ops (such as vsock sockets). Switch this to fallbacks to a
generic_file_splice_read instead.
Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Fri, 16 Nov 2018 07:38:36 +0000 (08:38 +0100)]
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Up until commit 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible") Signed-off-by: Martin Schiller <ms@dev.tdt.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Wed, 14 Nov 2018 11:54:49 +0000 (12:54 +0100)]
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab76 ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e0700 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Wed, 14 Nov 2018 11:17:25 +0000 (12:17 +0100)]
net/sched: act_pedit: fix memory leak when IDR allocation fails
tcf_idr_check_alloc() can return a negative value, on allocation failures
(-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases.
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 13 Nov 2018 16:48:28 +0000 (00:48 +0800)]
ipv6: fix a dst leak when removing its exception
These is no need to hold dst before calling rt6_remove_exception_rt().
The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(),
which has been removed in Commit 93531c674315 ("net/ipv6: separate
handling of FIB entries from dst based routes"). Otherwise, it will
cause a dst leak.
This patch is to simply remove the dst_hold_safe() call before calling
rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt().
It's safe, because the removal of the exception that holds its dst's
refcnt is protected by rt6_exception_lock.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Fixes: 23fb93a4d3f1 ("net/ipv6: Cleanup exception and cache route handling") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Using 2.5G speed relies on the SerDes lanes being configured
accordingly. The lanes have to be reconfigured to switch between
1G and 2.5G, and for now only the bootloader does this configuration.
In the case we add a Comphy driver to handle switching the lanes
dynamically, it's better for now to stick with supporting only 1G and
add advertisement for 2.5G once we really are capable of handling both
speeds without problem.
Since the interface mode is initialy taken from the DT, we want to make
sure that adding comphy support won't break boards that don't update
their dtb.
Fixes: da58a931f248 ("net: mvneta: Add support for 2500Mbps SGMII") Reported-by: Andrew Lunn <andrew@lunn.ch> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 16 Nov 2018 17:38:14 +0000 (11:38 -0600)]
Merge tag 'gfs2-4.20.fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull bfs2 fixes from Andreas Gruenbacher:
"Fix two bugs leading to leaked buffer head references:
- gfs2: Put bitmap buffers in put_super
- gfs2: Fix iomap buffer head reference counting bug
And one bug leading to significant slow-downs when deleting large
files:
- gfs2: Fix metadata read-ahead during truncate (2)"
* tag 'gfs2-4.20.fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix iomap buffer head reference counting bug
gfs2: Fix metadata read-ahead during truncate (2)
gfs2: Put bitmap buffers in put_super
gfs2: Fix iomap buffer head reference counting bug
GFS2 passes the inode buffer head (dibh) from gfs2_iomap_begin to
gfs2_iomap_end in iomap->private. It sets that private pointer in
gfs2_iomap_get. Users of gfs2_iomap_get other than gfs2_iomap_begin
would have to release iomap->private, but this isn't done correctly,
leading to a leak of buffer head references.
To fix this, move the code for setting iomap->private from
gfs2_iomap_get to gfs2_iomap_begin.
Linus Torvalds [Fri, 16 Nov 2018 16:37:27 +0000 (10:37 -0600)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Potential memory overwrite in simd
- Kernel info leaks in crypto_user
- NULL dereference and use-after-free in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Zeroize whole structure given to user space
crypto: user - fix leaking uninitialized memory to userspace
crypto: simd - correctly take reqsize of wrapped skcipher into account
crypto: hisilicon - Fix reference after free of memories on error path
crypto: hisilicon - Fix NULL dereference for same dst and src
Linus Torvalds [Fri, 16 Nov 2018 16:17:29 +0000 (10:17 -0600)]
Merge tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Live from Vancouver, SoC maintainer talk, this weeks drm fixes pull
for rc3:
omapdrm:
- regression fixes for the reordering bridge stuff that went into rc1
i915:
- incorrect EU count fix
- HPD storm fix
- MST fix
- relocation fix for gen4/5
amdgpu:
- huge page handling fix
- IH ring setup
- XGMI aperture setup
- watermark setup fix
misc:
- docs and MST fix"
* tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/i915: Account for scale factor when calculating initial phase
drm/i915: Clean up skl_program_scaler()
drm/i915: Move programming plane scaler to its own function.
drm/i915/icl: Drop spurious register read from icl_dbuf_slices_update
drm/i915: fix broadwell EU computation
drm/amdgpu: fix huge page handling on Vega10
drm/amd/pp: Fix truncated clock value when set watermark
drm/amdgpu: fix bug with IH ring setup
drm/meson: venc: dmt mode must use encp
drm/amdgpu: set system aperture to cover whole FB region
drm/i915: Fix hpd handling for pins with two encoders
drm/i915/execlists: Force write serialisation into context image vs execution
drm/i915/icl: Fix power well 2 wrt. DC-off toggling order
drm/i915: Fix NULL deref when re-enabling HPD IRQs on systems with MST
drm/i915: Fix possible race in intel_dp_add_mst_connector()
drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5
drm/omap: dsi: Fix missing of_platform_depopulate()
drm/omap: Move DISPC runtime PM handling to omapdrm
drm/omap: dsi: Ensure the device is active during probe
drm/omap: hdmi4: Ensure the device is active during bind
...
Linus Torvalds [Fri, 16 Nov 2018 16:14:54 +0000 (10:14 -0600)]
Merge tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of fixes since rc1.
- I broke 16-byte alignment of the stack when we moved PPR into
pt_regs. Despite being required by the ABI this broke almost
nothing, we eventually hit it in code where GCC does arithmetic on
the stack pointer assuming the bottom 4 bits are clear. Fix it by
padding the in-kernel pt_regs by 8 bytes.
- A couple of commits fixing minor bugs in the recent SLB rewrite.
- A build fix related to tracepoints in KVM in some configurations.
- Our old "IO workarounds" code written for Cell couldn't coexist in
a kernel that runs on Power9 with the Radix MMU, fix that.
- Remove the NPU DMA ops, these just printed a warning and should
never have been called.
- Suppress an overly chatty message triggered by CPU hotplug in some
configs.
- Two small selftest fixes.
Thanks to: Alistair Popple, Gustavo Romero, Nicholas Piggin, Satheesh
Rajendran, Scott Wood"
* tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Adjust wild_bctr to build with old binutils
powerpc/64: Fix kernel stack 16-byte alignment
powerpc/numa: Suppress "VPHN is not supported" messages
selftests/powerpc: Fix wild_bctr test to work on ppc64
powerpc/io: Fix the IO workarounds code to work with Radix
powerpc/mm/64s: Fix preempt warning in slb_allocate_kernel()
KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE
powerpc/mm/64s: Only use slbfee on CPUs that support it
powerpc/mm/64s: Use PPC_SLBFEE macro
powerpc/mm/64s: Consolidate SLB assertions
powerpc/powernv/npu: Remove NPU DMA ops
Linus Torvalds [Fri, 16 Nov 2018 16:10:27 +0000 (10:10 -0600)]
Merge tag 'xtensa-20181115' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- fix stack alignment for bFLT binaries.
- fix physical-to-virtual address translation for boot parameters in
MMUv3 256+256 and 512+512 virtual memory layouts.
* tag 'xtensa-20181115' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix boot parameters address translation
xtensa: make sure bFLT stack is 16 byte aligned
Linus Torvalds [Fri, 16 Nov 2018 15:31:59 +0000 (09:31 -0600)]
Merge tag 'for-linus-20181115' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Discard loop fix, caused by integer overflow (Dave)
- Blacklist of Samsung drive that hangs with power management (Diego)
- Copy bio priority when cloning it (Hannes)
- Fix race condition exposed in floppy (me)
- Fix SCSI queue cleanup regression. While elusive, it caused oopses in
queue running (Ming)
- Fix bad string copy in kyber tracing (Omar)
* tag 'for-linus-20181115' of git://git.kernel.dk/linux-block:
SCSI: fix queue cleanup race before queue initialization is done
block: fix 32 bit overflow in __blkdev_issue_discard()
libata: blacklist SAMSUNG MZ7TD256HAFV-000L9 SSD
block: copy ioprio in __bio_clone_fast() and bounce
kyber: fix wrong strlcpy() size in trace_kyber_latency()
floppy: fix race condition in __floppy_read_block_0()
Fixes: 291d57f67d244973 ("qed: Fix rdma_info structure allocation") Cc: Michal Kalderon <michal.kalderon@cavium.com> Cc: Denis Bolotin <denis.bolotin@cavium.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Thu, 15 Nov 2018 16:05:15 +0000 (18:05 +0200)]
net/mlx4: Fix UBSAN warning of signed integer overflow
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the uid variable to zero to avoid the compilation warning.
Fixes: 7a89399ffad7 ("net/mlx4: Add mlx4_bitmap zone allocator") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 15 Nov 2018 16:05:13 +0000 (18:05 +0200)]
net/mlx4_core: Zero out lkey field in SW2HW_MPT fw command
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Thu, 15 Nov 2018 22:52:14 +0000 (08:52 +1000)]
Merge tag 'drm-intel-fixes-2018-11-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix Bugzilla #108712: Fix incorrect EU count report from kernel
- Fix to account for scale factor when calculating initial phase on scaled output
- Avoid too trigger-happy HPD storm detection and fix a race and an OOPS for MST systems.
- Relocation race fix for Gen4/5
- A couple ICL fixes and dependencies for above Fixes:.
Fixes: ab408b6dc744 ("tcp: switch tcp and sch_fq to new earliest departure time model") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Mon, 12 Nov 2018 22:33:22 +0000 (22:33 +0000)]
rxrpc: Fix life check
The life-checking function, which is used by kAFS to make sure that a call
is still live in the event of a pending signal, only samples the received
packet serial number counter; it doesn't actually provoke a change in the
counter, rather relying on the server to happen to give us a packet in the
time window.
Fix this by adding a function to force a ping to be transmitted.
kAFS then keeps track of whether there's been a stall, and if so, uses the
new function to ping the server, resetting the timeout to allow the reply
to come back.
If there's a stall, a ping and the call is *still* stalled in the same
place after another period, then the call will be aborted.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Fixes: f4d15fb6f99a ("rxrpc: Provide functions for allowing cleaner handling of signals") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 15 Nov 2018 10:06:21 +0000 (15:36 +0530)]
cxgb4: fix thermal zone build error
with CONFIG_THERMAL=m and cxgb4 as built-in build fails, and
'commit e70a57fa59bb ("cxgb4: fix thermal configuration dependencies")'
tries to fix it but when cxgb4i is made built-in build fails again,
use IS_REACHABLE instead of IS_ENABLED to fix the issue.
Fixes: e70a57fa59bb (cxgb4: fix thermal configuration dependencies) Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thor Thayer [Mon, 12 Nov 2018 17:50:56 +0000 (11:50 -0600)]
MAINTAINERS: Replace Vince Bridgers as Altera TSE maintainer
Vince has moved to a different role. Replace him as Altera
TSE maintainer.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Acked-by: Vince Bridgers <vince.bridgers@intel.com> Acked-by: Alan Tull <atull@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Nov 2018 17:37:16 +0000 (09:37 -0800)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
Most of the bug fixes are related to the new 57500 chips, including some
initialization and counter fixes, disabling RDMA support, and a
workaround for occasional missing interrupts. The last patch from
Vasundhara fixes the year/month parameters for firmware coredump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Thu, 15 Nov 2018 08:25:42 +0000 (03:25 -0500)]
bnxt_en: Fix filling time in bnxt_fill_coredump_record()
Fix the year and month offset while storing it in
bnxt_fill_coredump_record().
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:40 +0000 (03:25 -0500)]
bnxt_en: Workaround occasional TX timeout on 57500 A0.
Hardware can sometimes not generate NQ MSIX with a single pending
CP ring entry. This seems to always happen at the last entry of
the CP ring before it wraps. Add logic to check all the CP rings for
pending entries without the CP ring consumer index advancing. Calling
HWRM_DBG_RING_INFO_GET to read the context of the CP ring will flush
out the NQ entry and MSIX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log