Linus Walleij [Sat, 3 Mar 2018 22:29:03 +0000 (23:29 +0100)]
mtd: jedec_probe: Fix crash in jedec_read_mfr()
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0") Cc: <stable@vger.kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Boris Brezillon [Tue, 27 Mar 2018 17:01:58 +0000 (19:01 +0200)]
mtd: nand: atmel: Fix get_sectorsize() function
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Cc: <stable@vger.kernel.org> Reported-by: Olivier Schonken <olivier.schonken@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
Linus Torvalds [Sun, 25 Mar 2018 17:45:10 +0000 (07:45 -1000)]
Merge tag 'dmaengine-fix-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"One small fix for stm32-dmamux fixing buffer overflow"
* tag 'dmaengine-fix-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/slave-dma:
dmaengine: stm32-dmamux: fix a potential buffer overflow
Linus Torvalds [Sun, 25 Mar 2018 17:36:02 +0000 (07:36 -1000)]
Merge branch 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 and PTI fixes from Ingo Molnar:
"Misc fixes:
- fix EFI pagetables freeing
- fix vsyscall pagetable setting on Xen PV guests
- remove ancient CONFIG_X86_PPRO_FENCE=y - x86 is TSO again
- fix two binutils (ld) development version related incompatibilities
- clean up breakpoint handling
- fix an x86 self-test"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Don't use IST entry for #BP stack
x86/efi: Free efi_pgd with free_pages()
x86/vsyscall/64: Use proper accessor to update P4D entry
x86/cpu: Remove the CONFIG_X86_PPRO_FENCE=y quirk
x86/boot/64: Verify alignment of the LOAD segment
x86/build/64: Force the linker to use 2MB page size
selftests/x86/ptrace_syscall: Fix for yet more glibc interference
Linus Torvalds [Sun, 25 Mar 2018 17:33:30 +0000 (07:33 -1000)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two sched debug output related fixes: a console output fix and
formatting fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Adjust newlines for better alignment
sched/debug: Fix per-task line continuation for console output
Linus Torvalds [Sun, 25 Mar 2018 17:27:32 +0000 (07:27 -1000)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc kernel side fixes.
Generic:
- cgroup events counting fix
x86:
- Intel PMU truncated-parameter fix
- RDPMC fix
- API naming fix/rename
- uncore driver big-hardware PCI enumeration fix
- uncore driver filter constraint fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/cgroup: Fix child event counting bug
perf/x86/intel/uncore: Fix multi-domain PCI CHA enumeration bug on Skylake servers
perf/x86/intel: Rename confusing 'freerunning PEBS' API and implementation to 'large PEBS'
perf/x86/intel/uncore: Add missing filter constraint for SKX CHA event
perf/x86/intel: Don't accidentally clear high bits in bdw_limit_period()
perf/x86/intel: Disable userspace RDPMC usage for large PEBS
Linus Torvalds [Sun, 25 Mar 2018 17:18:31 +0000 (07:18 -1000)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Two fixes: tighten up a jump-labels warning to not trigger on certain
modules and fix confusing (and non-existent) mutex API documentation"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
jump_label: Disable jump labels in __exit code
locking/mutex: Improve documentation
Linus Torvalds [Sun, 25 Mar 2018 06:29:15 +0000 (23:29 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull mqueuefs revert from Eric Biederman:
"This fixes a regression that came in the merge window for v4.16.
The problem is that the permissions for mounting and using the
mqueuefs filesystem are broken. The necessary permission check is
missing letting people who should not be able to mount mqueuefs mount
mqueuefs. The field sb->s_user_ns is set incorrectly not allowing the
mounter of mqueuefs to remount and otherwise have proper control over
the filesystem.
Al Viro and I see the path to the necessary fixes differently and I am
not even certain at this point he actually sees all of the necessary
fixes. Given a couple weeks we can probably work something out but I
don't see the review being resolved in time for the final v4.16. I
don't want v4.16 shipping with a nasty regression. So unfortunately I
am sending a revert"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
Revert "mqueue: switch to on-demand creation of internal mount"
Aleksa Sarai <asarai@suse.de> writes:
> [REGRESSION v4.16-rc6] [PATCH] mqueue: forbid unprivileged user access to internal mount
>
> Felix reported weird behaviour on 4.16.0-rc6 with regards to mqueue[1],
> which was introduced by 36735a6a2b5e ("mqueue: switch to on-demand
> creation of internal mount").
>
> Basically, the reproducer boils down to being able to mount mqueue if
> you create a new user namespace, even if you don't unshare the IPC
> namespace.
>
> Previously this was not possible, and you would get an -EPERM. The mount
> is the *host* mqueue mount, which is being cached and just returned from
> mqueue_mount(). To be honest, I'm not sure if this is safe or not (or if
> it was intentional -- since I'm not familiar with mqueue).
>
> To me it looks like there is a missing permission check. I've included a
> patch below that I've compile-tested, and should block the above case.
> Can someone please tell me if I'm missing something? Is this actually
> safe?
>
> [1]: https://github.com/docker/docker/issues/36674
The issue is a lot deeper than a missing permission check. sb->s_user_ns
was is improperly set as well. So in addition to the filesystem being
mounted when it should not be mounted, so things are not allow that should
be.
We are practically to the release of 4.16 and there is no agreement between
Al Viro and myself on what the code should looks like to fix things properly.
So revert the code to what it was before so that we can take our time
and discuss this properly.
Fixes: 36735a6a2b5e ("mqueue: switch to on-demand creation of internal mount") Reported-by: Felix Abecassis <fabecassis@nvidia.com> Reported-by: Aleksa Sarai <asarai@suse.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Linus Torvalds [Sat, 24 Mar 2018 16:50:12 +0000 (09:50 -0700)]
Merge tag 'pinctrl-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Two fixes for pin control for v4.16:
- Renesas SH-PFC: remove a duplicate clkout pin which was causing
crashes
- fix Samsung out of bounds exceptions"
* tag 'pinctrl-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Validate alias coming from DT
pinctrl: sh-pfc: r8a7795: remove duplicate of CLKOUT pin in pinmux_pins[]
Linus Torvalds [Fri, 23 Mar 2018 22:34:18 +0000 (15:34 -0700)]
Merge tag 'trace-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull kprobe fixes from Steven Rostedt:
"The documentation for kprobe events says that symbol offets can take
both a + and - sign to get to befor and after the symbol address.
But in actuality, the code does not support the minus. This fixes that
issue, and adds a few more selftests to kprobe events"
* tag 'trace-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests: ftrace: Add a testcase for probepoint
selftests: ftrace: Add a testcase for string type with kprobe_event
selftests: ftrace: Add probe event argument syntax testcase
tracing: probeevent: Fix to support minus offset from symbol
Andy Lutomirski [Thu, 23 Jul 2015 22:37:48 +0000 (15:37 -0700)]
x86/entry/64: Don't use IST entry for #BP stack
There's nothing IST-worthy about #BP/int3. We don't allow kprobes
in the small handful of places in the kernel that run at CPL0 with
an invalid stack, and 32-bit kernels have used normal interrupt
gates for #BP forever.
Furthermore, we don't allow kprobes in places that have usergs while
in kernel mode, so "paranoid" is also unnecessary.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org
Waiman Long [Thu, 22 Mar 2018 19:18:53 +0000 (15:18 -0400)]
x86/efi: Free efi_pgd with free_pages()
The efi_pgd is allocated as PGD_ALLOCATION_ORDER pages and therefore must
also be freed as PGD_ALLOCATION_ORDER pages with free_pages().
Fixes: d9e9a6418065 ("x86/mm/pti: Allocate a separate user PGD") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1521746333-19593-1-git-send-email-longman@redhat.com
Linus Torvalds [Fri, 23 Mar 2018 18:30:52 +0000 (11:30 -0700)]
Merge tag 'mips_fixes_4.16_5' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"Another miscellaneous pile of MIPS fixes for 4.16:
- lantiq: fixes for clocks and Amazon SE (4.14)
- ralink: fix booting on MT7621 (4.5)
- ralink: fix halt (3.9)"
* tag 'mips_fixes_4.16_5' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: ralink: Fix booting on MT7621
MIPS: ralink: Remove ralink_halt()
MIPS: lantiq: ase: Enable MFD_SYSCON
MIPS: lantiq: Enable AHB Bus for USB
MIPS: lantiq: Fix Danube USB clock
Linus Torvalds [Fri, 23 Mar 2018 17:59:38 +0000 (10:59 -0700)]
Merge tag 'media/v4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Three fixes:
- dvb: fix a Kconfig typo on a help text
- tegra-cec: reset rx_buf_cnt when start bit detected
- rc: lirc does not use LIRC_CAN_SEND_SCANCODE feature"
* tag 'media/v4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb: fix a Kconfig typo
media: tegra-cec: reset rx_buf_cnt when start bit detected
media: rc: lirc does not use LIRC_CAN_SEND_SCANCODE feature
Linus Torvalds [Fri, 23 Mar 2018 17:17:32 +0000 (10:17 -0700)]
Merge tag 'sound-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Things look calming down, but people were still busy to plaster over
small holes:
- Two fixes to harden against races in aloop driver
- A correction of a long-standing bug in USB-audio UAC2 processing
unit parser
- As usual suspects, HD-audio: a workaround for Coffee Lake
controller and a few other device-specific fixes
All small and for stable"
* tag 'sound-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: aloop: Fix access to not-yet-ready substream via cable
ALSA: aloop: Sync stale timer before release
ALSA: hda/realtek - Fix speaker no sound after system resume
ALSA: hda/realtek - Fix Dell headset Mic can't record
ALSA: hda - Force polling mode on CFL for fixing codec communication
ALSA: usb-audio: Fix parsing descriptor of UAC2 processing unit
ALSA: hda/realtek - Always immediately update mute LED with pin VREF
Masami Hiramatsu [Sat, 17 Mar 2018 12:38:10 +0000 (21:38 +0900)]
tracing: probeevent: Fix to support minus offset from symbol
In Documentation/trace/kprobetrace.txt, it says
@SYM[+|-offs] : Fetch memory at SYM +|- offs (SYM should be a data symbol)
However, the parser doesn't parse minus offset correctly, since
commit 2fba0c8867af ("tracing/kprobes: Fix probe offset to be
unsigned") drops minus ("-") offset support for kprobe probe
address usage.
This fixes the traceprobe_split_symbol_offset() to parse minus
offset again with checking the offset range, and add a minus
offset check in kprobe probe address usage.
Link: http://lkml.kernel.org/r/152129028983.31874.13419301530285775521.stgit@devbox Cc: Ingo Molnar <mingo@redhat.com> Cc: Tom Zanussi <tom.zanussi@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Fixes: 2fba0c8867af ("tracing/kprobes: Fix probe offset to be unsigned") Acked-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Linus Torvalds [Fri, 23 Mar 2018 01:48:43 +0000 (18:48 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, thp: do not cause memcg oom for thp
mm/vmscan: wake up flushers for legacy cgroups too
Revert "mm: page_alloc: skip over regions of invalid pfns where possible"
mm/shmem: do not wait for lock_page() in shmem_unused_huge_shrink()
mm/thp: do not wait for lock_page() in deferred_split_scan()
mm/khugepaged.c: convert VM_BUG_ON() to collapse fail
x86/mm: implement free pmd/pte page interfaces
mm/vmalloc: add interfaces to free unmapped page table
h8300: remove extraneous __BIG_ENDIAN definition
hugetlbfs: check for pgoff value overflow
lockdep: fix fs_reclaim warning
MAINTAINERS: update Mark Fasheh's e-mail
mm/mempolicy.c: avoid use uninitialized preferred_node
Linus Torvalds [Fri, 23 Mar 2018 01:37:49 +0000 (18:37 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Two regression fixes, two bug fixes for older issues, two fixes for
new functionality added this cycle that have userspace ABI concerns,
and a small cleanup. These have appeared in a linux-next release and
have a build success report from the 0day robot.
* The 4.16 rework of altmap handling led to some configurations
leaking page table allocations due to freeing from the altmap
reservation rather than the page allocator.
The impact without the fix is leaked memory and a WARN() message
when tearing down libnvdimm namespaces. The rework also missed a
place where error handling code needed to be removed that can lead
to a crash if devm_memremap_pages() fails.
* acpi_map_pxm_to_node() had a latent bug whereby it could
misidentify the closest online node to a given proximity domain.
* Block integrity handling was reworked several kernels back to allow
calling add_disk() after setting up the integrity profile.
The nd_btt and nd_blk drivers are just now catching up to fix
automatic partition detection at driver load time.
* The new peristence_domain attribute, a platform indicator of
whether cpu caches are powerfail protected for example, is meant to
be a single value enum and not a set of flags.
This oversight was caught while reviewing new userspace code in
libndctl to communicate the attribute.
Fix this new enabling up so that we are not stuck with an unwanted
userspace ABI"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, nfit: fix persistence domain reporting
libnvdimm, region: hide persistence_domain when unknown
acpi, numa: fix pxm to online numa node associations
x86, memremap: fix altmap accounting at free
libnvdimm: remove redundant assignment to pointer 'dev'
libnvdimm, {btt, blk}: do integrity setup before add_disk()
kernel/memremap: Remove stale devres_free() call
Linus Torvalds [Fri, 23 Mar 2018 00:37:44 +0000 (17:37 -0700)]
Merge tag 'drm-fixes-for-v4.16-rc7' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes all over the place (core, i915, amdgpu, imx, sun4i,
ast, tegra, vmwgfx), nothing too serious or worrying at this stage.
- one uapi fix to stop multi-planar images with getfb
- Sun4i error path and clock fixes
- udl driver mmap offset fix
- i915 DP MST and GPU reset fixes
- vmwgfx mutex and black screen fixes
- imx array underflow fix and vblank fix
- amdgpu: display fixes
- exynos devicetree fix
- ast mode fix"
* tag 'drm-fixes-for-v4.16-rc7' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/ast: Fixed 1280x800 Display Issue
drm: udl: Properly check framebuffer mmap offsets
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/vmwgfx: Fix a destoy-while-held mutex problem.
drm/vmwgfx: Fix black screen and device errors when running without fbdev
drm: Reject getfb for multi-plane framebuffers
drm/amd/display: Add one to EDID's audio channel count when passing to DC
drm/amd/display: We shouldn't set format_default on plane as atomic driver
drm/amd/display: Fix FMT truncation programming
drm/amd/display: Allow truncation to 10 bits
drm/sun4i: hdmi: Fix another error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: hdmi: Fix an error handling path in 'sun4i_hdmi_bind()'
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
drm/amd/display: fix dereferencing possible ERR_PTR()
drm/amd/display: Refine disable VGA
drm/tegra: Shutdown on driver unbind
drm/tegra: dsi: Don't disable regulator on ->exit()
drm/tegra: dc: Detach IOMMU group from domain only once
dt-bindings: exynos: Document #sound-dai-cells property of the HDMI node
drm/imx: move arming of the vblank event to atomic_flush
...
David Rientjes [Thu, 22 Mar 2018 23:17:45 +0000 (16:17 -0700)]
mm, thp: do not cause memcg oom for thp
Commit 2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and
madvised allocations") changed the page allocator to no longer detect
thp allocations based on __GFP_NORETRY.
It did not, however, modify the mem cgroup try_charge() path to avoid
oom kill for either khugepaged collapsing or thp faulting. It is never
expected to oom kill a process to allocate a hugepage for thp; reclaim
is governed by the thp defrag mode and MADV_HUGEPAGE, but allocations
(and charging) should fallback instead of oom killing processes.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1803191409420.124411@chino.kir.corp.google.com Fixes: 2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations") Signed-off-by: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 22 Mar 2018 23:17:42 +0000 (16:17 -0700)]
mm/vmscan: wake up flushers for legacy cgroups too
Commit 726d061fbd36 ("mm: vmscan: kick flushers when we encounter dirty
pages on the LRU") added flusher invocation to shrink_inactive_list()
when many dirty pages on the LRU are encountered.
However, shrink_inactive_list() doesn't wake up flushers for legacy
cgroup reclaim, so the next commit bbef938429f5 ("mm: vmscan: remove old
flusher wakeup from direct reclaim path") removed the only source of
flusher's wake up in legacy mem cgroup reclaim path.
This leads to premature OOM if there is too many dirty pages in cgroup:
# mkdir /sys/fs/cgroup/memory/test
# echo $$ > /sys/fs/cgroup/memory/test/tasks
# echo 50M > /sys/fs/cgroup/memory/test/memory.limit_in_bytes
# dd if=/dev/zero of=tmp_file bs=1M count=100
Killed
Daniel Vacek [Thu, 22 Mar 2018 23:17:38 +0000 (16:17 -0700)]
Revert "mm: page_alloc: skip over regions of invalid pfns where possible"
This reverts commit b92df1de5d28 ("mm: page_alloc: skip over regions of
invalid pfns where possible"). The commit is meant to be a boot init
speed up skipping the loop in memmap_init_zone() for invalid pfns.
But given some specific memory mapping on x86_64 (or more generally
theoretically anywhere but on arm with CONFIG_HAVE_ARCH_PFN_VALID) the
implementation also skips valid pfns which is plain wrong and causes
'kernel BUG at mm/page_alloc.c:1389!'
Replace lock_page() with trylock_page() and skip the page if we failed
to lock it. We will get to the page on the next scan.
We can test for the PageTransHuge() outside the page lock as we only
need protection against splitting the page under us. Holding pin oni
the page is enough for this.
Link: http://lkml.kernel.org/r/20180316210830.43738-1-kirill.shutemov@linux.intel.com Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Eric Wheeler <linux-mm@lists.ewheeler.net> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/khugepaged.c: convert VM_BUG_ON() to collapse fail
khugepaged is not yet able to convert PTE-mapped huge pages back to PMD
mapped. We do not collapse such pages. See check
khugepaged_scan_pmd().
But if between khugepaged_scan_pmd() and __collapse_huge_page_isolate()
somebody managed to instantiate THP in the range and then split the PMD
back to PTEs we would have a problem --
VM_BUG_ON_PAGE(PageCompound(page)) will get triggered.
It's possible since we drop mmap_sem during collapse to re-take for
write.
Replace the VM_BUG_ON() with graceful collapse fail.
Link: http://lkml.kernel.org/r/20180315152353.27989-1-kirill.shutemov@linux.intel.com Fixes: b1caa957ae6d ("khugepaged: ignore pmd tables with THP mapped with ptes") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshi Kani [Thu, 22 Mar 2018 23:17:20 +0000 (16:17 -0700)]
mm/vmalloc: add interfaces to free unmapped page table
On architectures with CONFIG_HAVE_ARCH_HUGE_VMAP set, ioremap() may
create pud/pmd mappings. A kernel panic was observed on arm64 systems
with Cortex-A75 in the following steps as described by Hanjun Guo.
1. ioremap a 4K size, valid page table will build,
2. iounmap it, pte0 will set to 0;
3. ioremap the same address with 2M size, pgd/pmd is unchanged,
then set the a new value for pmd;
4. pte0 is leaked;
5. CPU may meet exception because the old pmd is still in TLB,
which will lead to kernel panic.
This panic is not reproducible on x86. INVLPG, called from iounmap,
purges all levels of entries associated with purged address on x86. x86
still has memory leak.
The patch changes the ioremap path to free unmapped page table(s) since
doing so in the unmap path has the following issues:
- The iounmap() path is shared with vunmap(). Since vmap() only
supports pte mappings, making vunmap() to free a pte page is an
overhead for regular vmap users as they do not need a pte page freed
up.
- Checking if all entries in a pte page are cleared in the unmap path
is racy, and serializing this check is expensive.
- The unmap path calls free_vmap_area_noflush() to do lazy TLB purges.
Clearing a pud/pmd entry before the lazy TLB purges needs extra TLB
purge.
Add two interfaces, pud_free_pmd_page() and pmd_free_pte_page(), which
clear a given pud/pmd entry and free up a page for the lower level
entries.
This patch implements their stub functions on x86 and arm64, which work
as workaround.
[akpm@linux-foundation.org: fix typo in pmd_free_pte_page() stub] Link: http://lkml.kernel.org/r/20180314180155.19492-2-toshi.kani@hpe.com Fixes: e61ce6ade404e ("mm: change ioremap to set up huge I/O mappings") Reported-by: Lei Li <lious.lilei@hisilicon.com> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Wang Xuefeng <wxf.wang@hisilicon.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Borislav Petkov <bp@suse.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Chintan Pandya <cpandya@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Thu, 22 Mar 2018 23:17:13 +0000 (16:17 -0700)]
hugetlbfs: check for pgoff value overflow
A vma with vm_pgoff large enough to overflow a loff_t type when
converted to a byte offset can be passed via the remap_file_pages system
call. The hugetlbfs mmap routine uses the byte offset to calculate
reservations and file size.
The overflowed pgoff value causes hugetlbfs to try to set up a mapping
with a negative range (end < start) that leaves invalid state which
causes the BUG.
The previous overflow fix to this code was incomplete and did not take
the remap_file_pages system call into account.
[mike.kravetz@oracle.com: v3] Link: http://lkml.kernel.org/r/20180309002726.7248-1-mike.kravetz@oracle.com
[akpm@linux-foundation.org: include mmdebug.h]
[akpm@linux-foundation.org: fix -ve left shift count on sh] Link: http://lkml.kernel.org/r/20180308210502.15952-1-mike.kravetz@oracle.com Fixes: 045c7a3f53d9 ("hugetlbfs: fix offset overflow in hugetlbfs mmap") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Nic Losby <blurbdust@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This warning is caused by commit d92a8cfcb37e ("locking/lockdep:
Rework FS_RECLAIM annotation") which replaced the use of
lockdep_{set,clear}_current_reclaim_state() in __perform_reclaim()
and lockdep_trace_alloc() in slab_pre_alloc_hook() with
fs_reclaim_acquire()/ fs_reclaim_release().
Since __kmalloc_reserve() from __alloc_skb() adds __GFP_NOMEMALLOC |
__GFP_NOWARN to gfp_mask, and all reclaim path simply propagates
__GFP_NOMEMALLOC, fs_reclaim_acquire() in slab_pre_alloc_hook() is
trying to grab the 'fake' lock again when __perform_reclaim() already
grabbed the 'fake' lock.
The
/* this guy won't enter reclaim */
if ((current->flags & PF_MEMALLOC) && !(gfp_mask & __GFP_NOMEMALLOC))
return false;
test which causes slab_pre_alloc_hook() to try to grab the 'fake' lock
was added by commit cf40bd16fdad ("lockdep: annotate reclaim context
(__GFP_NOFS)"). But that test is outdated because PF_MEMALLOC thread
won't enter reclaim regardless of __GFP_NOMEMALLOC after commit 341ce06f69ab ("page allocator: calculate the alloc_flags for allocation
only once") added the PF_MEMALLOC safeguard (
/* Avoid recursion of direct reclaim */
if (p->flags & PF_MEMALLOC)
goto nopage;
in __alloc_pages_slowpath()).
Thus, let's fix outdated test by removing __GFP_NOMEMALLOC test and
allow __need_fs_reclaim() to return false.
Link: http://lkml.kernel.org/r/201802280650.FJC73911.FOSOMLJVFFQtHO@I-love.SAKURA.ne.jp Fixes: d92a8cfcb37ecd13 ("locking/lockdep: Rework FS_RECLAIM annotation") Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Dave Jones <davej@codemonkey.org.uk> Tested-by: Dave Jones <davej@codemonkey.org.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Nick Piggin <npiggin@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Nikolay Borisov <nborisov@suse.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yisheng Xie [Thu, 22 Mar 2018 23:17:02 +0000 (16:17 -0700)]
mm/mempolicy.c: avoid use uninitialized preferred_node
Alexander reported a use of uninitialized memory in __mpol_equal(),
which is caused by incorrect use of preferred_node.
When mempolicy in mode MPOL_PREFERRED with flags MPOL_F_LOCAL, it uses
numa_node_id() instead of preferred_node, however, __mpol_equal() uses
preferred_node without checking whether it is MPOL_F_LOCAL or not.
[akpm@linux-foundation.org: slight comment tweak] Link: http://lkml.kernel.org/r/4ebee1c2-57f6-bcb8-0e2d-1833d1ee0bb7@huawei.com Fixes: fc36b8d3d819 ("mempolicy: use MPOL_F_LOCAL to Indicate Preferred Local Policy") Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com> Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 22 Mar 2018 23:20:25 +0000 (16:20 -0700)]
Merge tag 'acpi-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert one recent commit that added incorrect battery quirks for
some Asus systems and fix an off-by-one error in the watchdog driver
based on the ACPI WDAT table.
Specifics:
- Revert the recent change adding battery quirks for Asus GL502VSK
and UX305LA as these quirks turn out to be inadequate and possibly
premature (Daniel Drake).
- Fix an off-by-one error in the resource allocation part of the
watchdog driver based on the ACPI WDAT table (Takashi Iwai)"
* tag 'acpi-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / watchdog: Fix off-by-one error at resource assignment
Revert "ACPI / battery: Add quirk for Asus GL502VSK and UX305LA"
1) Always validate XFRM esn replay attribute, from Florian Westphal.
2) Fix RCU read lock imbalance in xfrm_get_tos(), from Xin Long.
3) Don't try to get firmware dump if not loaded in iwlwifi, from Shaul
Triebitz.
4) Fix BPF helpers to deal with SCTP GSO SKBs properly, from Daniel
Axtens.
5) Fix some interrupt handling issues in e1000e driver, from Benjamin
Poitier.
6) Use strlcpy() in several ethtool get_strings methods, from Florian
Fainelli.
7) Fix rhlist dup insertion, from Paul Blakey.
8) Fix SKB leak in netem packet scheduler, from Alexey Kodanev.
9) Fix driver unload crash when link is up in smsc911x, from Jeremy
Linton.
10) Purge out invalid socket types in l2tp_tunnel_create(), from Eric
Dumazet.
11) Need to purge the write queue when TCP connections are aborted,
otherwise userspace using MSG_ZEROCOPY can't close the fd. From
Soheil Hassas Yeganeh.
12) Fix double free in error path of team driver, from Arkadi
Sharshevsky.
13) Filter fixes for hv_netvsc driver, from Stephen Hemminger.
14) Fix non-linear packet access in ipv6 ndisc code, from Lorenzo
Bianconi.
15) Properly filter out unsupported feature flags in macvlan driver,
from Shannon Nelson.
16) Don't request loading the diag module for a protocol if the protocol
itself is not even registered. From Xin Long.
17) If datagram connect fails in ipv6, make sure the socket state is
consistent afterwards. From Paolo Abeni.
18) Use after free in qed driver, from Dan Carpenter.
19) If received ipv4 PMTU is less than the min pmtu, lock the mtu in the
entry. From Sabrina Dubroca.
20) Fix sleep in atomic in tg3 driver, from Jonathan Toppins.
21) Fix vlan in vlan untagging in some situations, from Toshiaki Makita.
22) Fix double SKB free in genlmsg_mcast(). From Nicolas Dichtel.
23) Fix NULL derefs in error paths of tcf_*_init(), from Davide Caratti.
24) Unbalanced PM runtime calls in FEC driver, from Florian Fainelli.
25) Memory leak in gemini driver, from Igor Pylypiv.
26) IDR leaks in error paths of tcf_*_init() functions, from Davide
Caratti.
27) Need to use GFP_ATOMIC in seg6_build_state(), from David Lebrun.
28) Missing dev_put() in error path of macsec_newlink(), from Dan
Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (201 commits)
macsec: missing dev_put() on error in macsec_newlink()
net: dsa: Fix functional dsa-loop dependency on FIXED_PHY
hv_netvsc: common detach logic
hv_netvsc: change GPAD teardown order on older versions
hv_netvsc: use RCU to fix concurrent rx and queue changes
hv_netvsc: disable NAPI before channel close
net/ipv6: Handle onlink flag with multipath routes
ppp: avoid loop in xmit recursion detection code
ipv6: sr: fix NULL pointer dereference when setting encap source address
ipv6: sr: fix scheduling in RCU when creating seg6 lwtunnel state
net: aquantia: driver version bump
net: aquantia: Implement pci shutdown callback
net: aquantia: Allow live mac address changes
net: aquantia: Add tx clean budget and valid budget handling logic
net: aquantia: Change inefficient wait loop on fw data reads
net: aquantia: Fix a regression with reset on old firmware
net: aquantia: Fix hardware reset when SPI may rarely hangup
s390/qeth: on channel error, reject further cmd requests
s390/qeth: lock read device while queueing next buffer
s390/qeth: when thread completes, wake up all waiters
...
Linus Torvalds [Thu, 22 Mar 2018 20:29:55 +0000 (13:29 -0700)]
Merge tag 'mmc-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes intended for v4.16-rc7:
MMC host:
- dw_mmc: Fix the suspend/resume issue for Exynos5433
- dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit
systems
- dw_mmc: Make PIO mode work when failing with idmac when
dw_mci_reset occurs
- sdhci-acpi: Re-allow IRQ 0 to fix broken probe
MMC core:
- Update EXT_CSD caches to correctly switch partition for ioctl calls
- Fix tracepoint print of blk_addr and blksz
- Disable HPI on broken Micron (Numonyx) eMMC cards"
* tag 'mmc-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-acpi: Fix IRQ 0
mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs
mmc: core: Fix tracepoint print of blk_addr and blksz
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: dw_mmc: exynos: fix the suspend/resume issue for exynos5433
mmc: block: fix updating ext_csd caches on ioctl call
mmc: dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit systems
Dave Airlie [Thu, 22 Mar 2018 20:19:56 +0000 (06:19 +1000)]
Merge tag 'drm-misc-fixes-2018-03-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Main change is a patch to reject getfb call for multiplanar framebuffers,
then we have a couple of error path fixes on the sun4i driver. Still on that
driver there is a clk fix and finally a mmap offset fix on the udl driver.
* tag 'drm-misc-fixes-2018-03-22' of git://anongit.freedesktop.org/drm/drm-misc:
drm: udl: Properly check framebuffer mmap offsets
drm: Reject getfb for multi-plane framebuffers
drm/sun4i: hdmi: Fix another error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: hdmi: Fix an error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: Fix an error handling path in 'sun4i_drv_bind()'
drm/sun4i: Fix exclusivity of the TCON clocks
Dave Airlie [Thu, 22 Mar 2018 20:15:44 +0000 (06:15 +1000)]
Merge tag 'drm-intel-fixes-2018-03-21' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
One fix for DP MST and one fix for GPU reset on hang check.
* tag 'drm-intel-fixes-2018-03-21' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
Dave Airlie [Thu, 22 Mar 2018 20:15:08 +0000 (06:15 +1000)]
Merge branch 'vmwgfx-fixes-4.16' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Two vmwgfx fixes for 4.16. Both cc'd stable.
* 'vmwgfx-fixes-4.16' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix a destoy-while-held mutex problem.
drm/vmwgfx: Fix black screen and device errors when running without fbdev
Dave Airlie [Thu, 22 Mar 2018 20:14:15 +0000 (06:14 +1000)]
Merge tag 'imx-drm-fixes-2018-03-22' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: fixes for early vblank event issue, array underflow error
- fix an array underflow error by reordering the range check before the array
subscript in ipu-prg.
- make some local functions static in ipuv3-plane.
- add a missng header for ipu_planes_assign_pre in ipuv3-plane.
- move arming of the vblank event from atomic_begin to atomic_flush, to avoid
signalling atomic commit completion to userspace before plane atomic_update
has finished, due to a race condition that is likely to be hit on i.MX6QP on
PRE enabled channels.
* tag 'imx-drm-fixes-2018-03-22' of git://git.pengutronix.de/git/pza/linux:
drm/imx: move arming of the vblank event to atomic_flush
drm/imx: ipuv3-plane: Include "imx-drm.h" header file
drm/imx: ipuv3-plane: Make functions static when possible
gpu: ipu-v3: prg: avoid possible array underflow
Dan Carpenter [Wed, 21 Mar 2018 08:09:01 +0000 (11:09 +0300)]
macsec: missing dev_put() on error in macsec_newlink()
We moved the dev_hold(real_dev); call earlier in the function but forgot
to update the error paths.
Fixes: 0759e552bce7 ("macsec: fix negative refcnt on parent link") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 17:19:10 +0000 (13:19 -0400)]
Merge tag 'mac80211-for-davem-2018-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two more fixes (in three patches):
* ath9k_htc doesn't like QoS NDP frames, use regular ones
* hwsim: set up wmediumd for radios created later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 21 Mar 2018 00:31:10 +0000 (17:31 -0700)]
net: dsa: Fix functional dsa-loop dependency on FIXED_PHY
We have a functional dependency on the FIXED_PHY MDIO bus because we register
fixed PHY devices "the old way" which only works if the code that does this has
had a chance to run before the fixed MDIO bus is probed. Make sure we account
for that and have dsa_loop_bdinfo.o be either built-in or modular depending on
whether CONFIG_FIXED_PHY reflects that too.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
hv_netvsc: fix races during shutdown and changes
This set of patches fixes issues identified by Vitaly Kuznetsov and
Mohammed Gamal related to state changes in Hyper-v network driver.
A lot of the issues are because setting up the netvsc device requires
a second step (in work queue) to get all the sub-channels running.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make common function for detaching internals of device
during changes to MTU and RSS. Make sure no more packets
are transmitted and all packets have been received before
doing device teardown.
Change the wait logic to be common and use usleep_range().
Changes transmit enabling logic so that transmit queues are disabled
during the period when lower device is being changed. And enabled
only after sub channels are setup. This avoids issue where it could
be that a packet was being sent while subchannel was not initialized.
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: change GPAD teardown order on older versions
On older versions of Windows, the host ignores messages after
vmbus channel is closed.
Workaround this by doing what Windows does and send the teardown
before close on older versions of NVSP protocol.
Reported-by: Mohammed Gamal <mgamal@redhat.com> Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: use RCU to fix concurrent rx and queue changes
The receive processing may continue to happen while the
internal network device state is in RCU grace period.
The internal RNDIS structure is associated with the
internal netvsc_device structure; both have the same
RCU lifetime.
Defer freeing all associated parts until after grace
period.
Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure that no CPU is still process packets when
the channel is closed.
Fixes: 76bb5db5c749 ("netvsc: fix use after free on module removal") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 20 Mar 2018 17:06:59 +0000 (10:06 -0700)]
net/ipv6: Handle onlink flag with multipath routes
For multipath routes the ONLINK flag can be specified per nexthop in
rtnh_flags or globally in rtm_flags. Update ip6_route_multipath_add
to consider the ONLINK setting coming from rtnh_flags. Each loop over
nexthops the config for the sibling route is initialized to the global
config and then per nexthop settings overlayed. The flag is 'or'ed into
fib6_config to handle the ONLINK flag coming from either rtm_flags or
rtnh_flags.
Fixes: fc1e64e1092f ("net/ipv6: Add support for onlink flag") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Tue, 20 Mar 2018 15:49:26 +0000 (16:49 +0100)]
ppp: avoid loop in xmit recursion detection code
We already detect situations where a PPP channel sends packets back to
its upper PPP device. While this is enough to avoid deadlocking on xmit
locks, this doesn't prevent packets from looping between the channel
and the unit.
The problem is that ppp_start_xmit() enqueues packets in ppp->file.xq
before checking for xmit recursion. Therefore, __ppp_xmit_process()
might dequeue a packet from ppp->file.xq and send it on the channel
which, in turn, loops it back on the unit. Then ppp_start_xmit()
queues the packet back to ppp->file.xq and __ppp_xmit_process() picks
it up and sends it again through the channel. Therefore, the packet
will loop between __ppp_xmit_process() and ppp_start_xmit() until some
other part of the xmit path drops it.
For L2TP, we rapidly fill the skb's headroom and pppol2tp_xmit() drops
the packet after a few iterations. But PPTP reallocates the headroom
if necessary, letting the loop run and exhaust the machine resources
(as reported in https://bugzilla.kernel.org/show_bug.cgi?id=199109).
Fix this by letting __ppp_xmit_process() enqueue the skb to
ppp->file.xq, so that we can check for recursion before adding it to
the queue. Now ppp_xmit_process() can drop the packet when recursion is
detected.
__ppp_channel_push() is a bit special. It calls __ppp_xmit_process()
without having any actual packet to send. This is used by
ppp_output_wakeup() to re-enable transmission on the parent unit (for
implementations like ppp_async.c, where the .start_xmit() function
might not consume the skb, leaving it in ppp->xmit_pending and
disabling transmission).
Therefore, __ppp_xmit_process() needs to handle the case where skb is
NULL, dequeuing as many packets as possible from ppp->file.xq.
Reported-by: xu heng <xuheng333@zoho.com> Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
When using seg6 in encap mode, we call ipv6_dev_get_saddr() to set the
source address of the outer IPv6 header, in case none was specified.
Using skb->dev can lead to BUG() when it is in an inconsistent state.
This patch uses the net_device attached to the skb's dst instead.
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Reported-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 16:02:50 +0000 (12:02 -0400)]
Merge branch 'aquantia-fixes'
Igor Russkikh says:
====================
Aquantia atlantic hot fixes 03-2018
This is a set of atlantic driver hot fixes for various areas:
Some issues with hardware reset covered,
Fixed napi_poll flood happening on some traffic conditions,
Allow system to change MAC address on live device,
Add pci shutdown handler.
patch v2:
- reverse christmas tree
- remove driver private parameter, replacing it with define.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:36 +0000 (14:40 +0300)]
net: aquantia: Implement pci shutdown callback
We should close link and all NIC operations during shutdown.
On some systems graceful reboot never closes NIC interface on its own,
but only indicates pci device shutdown. Without explicit handler, NIC
rx rings continued to transfer DMA data into prepared buffers while CPU
rebooted already. That caused memory corruptions on soft reboot.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should report to napi full budget only when we have more job to do.
Before this fix, on any tx queue cleanup we forced napi to do poll again.
Thats a waste of cpu resources and caused storming with napi polls when
there was at least one tx on each interrupt.
With this fix we report full budget only when there is more job on TX
to do. Or, as before, when rx budget was fully consumed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:33 +0000 (14:40 +0300)]
net: aquantia: Change inefficient wait loop on fw data reads
B1 hardware changes behavior of mailbox interface, it has busy bit
always raised. Data ready condition should be detected by increment
of address register.
Old code has empty `for` loop, and that caused cpu overloads on B1
hardware. aq_nic_service_timer_cb consumed ~100ms because of that.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:31 +0000 (14:40 +0300)]
net: aquantia: Fix hardware reset when SPI may rarely hangup
Under some circumstances (notably using thunderbolt interface) SPI
on chip reset may be in active transaction.
Here we forcibly cleanup SPI to prevent possible hangups.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 15:52:31 +0000 (11:52 -0400)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-03-20
Please apply one final set of qeth patches for 4.16.
All of these fix long-standing bugs, so please queue them up for -stable
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:15 +0000 (07:59 +0100)]
s390/qeth: on channel error, reject further cmd requests
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:14 +0000 (07:59 +0100)]
s390/qeth: lock read device while queueing next buffer
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:13 +0000 (07:59 +0100)]
s390/qeth: when thread completes, wake up all waiters
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: Add general dummy stubs for MMD register access
v2:
As suggested by Andrew:
- Add general dummy stubs
- Also use that for the micrel phy
This patch series fix the Ethernet broken on the mpc8315erdb board introduced
by commit b6b5e8a69118 ("gianfar: Disable EEE autoneg by default").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Tue, 20 Mar 2018 01:44:53 +0000 (09:44 +0800)]
net: phy: realtek: Use the dummy stubs for MMD register access for rtl8211b
The Ethernet on mpc8315erdb is broken since commit b6b5e8a69118
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default") Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Tue, 20 Mar 2018 01:44:52 +0000 (09:44 +0800)]
net: phy: Add general dummy stubs for MMD register access
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default") Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Thu, 15 Feb 2018 16:21:55 +0000 (17:21 +0100)]
posix-timers: Protect posix clock array access against speculation
The clockid argument of clockid_to_kclock() comes straight from user space
via various syscalls and is used as index into the posix_clocks array.
Protect it against spectre v1 array out of bounds speculation. Remove the
redundant check for !posix_clock[id] as this is another source for
speculation and does not provide any advantage over the return
posix_clock[id] path which returns NULL in that case anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: David Woodhouse <dwmw@amazon.co.uk> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802151718320.1296@nanos.tec.linutronix.de
Takashi Iwai [Thu, 22 Mar 2018 09:40:27 +0000 (10:40 +0100)]
ALSA: aloop: Fix access to not-yet-ready substream via cable
In loopback_open() and loopback_close(), we assign and release the
substream object to the corresponding cable in a racy way. It's
neither locked nor done in the right position. The open callback
assigns the substream before its preparation finishes, hence the other
side of the cable may pick it up, which may lead to the invalid memory
access.
This patch addresses these: move the assignment to the end of the open
callback, and wrap with cable->lock for avoiding concurrent accesses.
Takashi Iwai [Thu, 22 Mar 2018 07:56:06 +0000 (08:56 +0100)]
ALSA: aloop: Sync stale timer before release
The aloop driver tries to stop the pending timer via timer_del() in
the trigger callback and in the close callback. The former is
correct, as it's an atomic operation, while the latter expects that
the timer gets really removed and proceeds the resource releases after
that. But timer_del() doesn't synchronize, hence the running timer
may still access the released resources.
A similar situation can be also seen in the prepare callback after
trigger(STOP) where the prepare tries to re-initialize the things
while a timer is still running.
The problems like the above are seen indirectly in some syzkaller
reports (although it's not 100% clear whether this is the only cause,
as the race condition is quite narrow and not always easy to
trigger).
For addressing these issues, this patch adds the explicit alls of
timer_del_sync() in some places, so that the pending timer is properly
killed / synced.
Kailang Yang [Wed, 14 Mar 2018 08:08:57 +0000 (16:08 +0800)]
ALSA: hda/realtek - Fix speaker no sound after system resume
It will have a chance speaker no sound after system resume.
To toggle NID 0x53 index 0x2 bit 15 will solve this issue.
This usage will also suitable with ALC256.
Fixes: 4a219ef8f370 ("ALSA: hda/realtek - Add ALC256 HP depop function") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memmap options sent to the udl framebuffer driver were not being
checked for all sets of possible crazy values. Fix this up by properly
bounding the allowed values.
dmaengine: stm32-dmamux: fix a potential buffer overflow
The bitfield dma_inuse is allocated of size dma_requests bits, thus a
valid bit address is from 0 to (dma_requests - 1).
When find_first_zero_bit() fails, it returns dma_requests as invalid
address.
Using such address for the following set_bit() is incorrect and, if
dma_requests is a multiple of BITS_PER_LONG, it will cause a buffer
overflow.
Currently this driver is only used in DT stm32h743.dtsi where a safe value
dma_requests=16 is not triggering the buffer overflow.
Fixed by checking the return value of find_first_zero_bit() _before_
using it.
The intent of commit 2170dd04316e ("vfio-pci: Mask INTx if a device is
not capabable of enabling it") was to disallow the user from seeing
that the device supports INTx if the platform is incapable of enabling
it. The detection of this case however incorrectly includes devices
which natively do not support INTx, such as SR-IOV VFs, and further
discussions reveal gaps even for the target use case.
Reported-by: Arjun Vynipadath <arjun@chelsio.com> Fixes: 2170dd04316e ("vfio-pci: Mask INTx if a device is not capabable of enabling it") Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
NeilBrown [Wed, 21 Mar 2018 03:02:10 +0000 (14:02 +1100)]
MIPS: ralink: Fix booting on MT7621
Since commit 3af5a67c86a3 ("MIPS: Fix early CM probing") the MT7621 has
not been able to boot.
This commit caused mips_cm_probe() to be called before
mt7621.c::proc_soc_init().
prom_soc_init() has a comment explaining that mips_cm_probe() "wipes out
the bootloader config" and means that configuration registers are no
longer available. It has some code to re-enable this config.
Before this re-enable code is run, the sysc register cannot be read, so
when SYSC_REG_CHIP_NAME0 is read, a garbage value is returned and
panic() is called.
If we move the config-repair code to the top of prom_soc_init(), the
registers can be read and boot can proceed.
Very occasionally, the first register read after the reconfiguration
returns garbage, so add a call to __sync().
Fixes: 3af5a67c86a3 ("MIPS: Fix early CM probing") Signed-off-by: NeilBrown <neil@brown.name> Reviewed-by: Matt Redfearn <matt.redfearn@mips.com> Cc: John Crispin <john@phrozen.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.5+
Patchwork: https://patchwork.linux-mips.org/patch/18859/ Signed-off-by: James Hogan <jhogan@kernel.org>
NeilBrown [Tue, 20 Mar 2018 08:29:51 +0000 (19:29 +1100)]
MIPS: ralink: Remove ralink_halt()
ralink_halt() does nothing that machine_halt() doesn't already do, so it
adds no value.
It actually causes incorrect behaviour due to the "unreachable()" at the
end. This tells the compiler that the end of the function will never be
reached, which isn't true. The compiler responds by not adding a
'return' instruction, so control simply moves on to whatever bytes come
afterwards in memory. In my tested, that was the ralink_restart()
function. This means that an attempt to 'halt' the machine would
actually cause a reboot.
So remove ralink_halt() so that a 'halt' really does halt.
Dave Airlie [Wed, 21 Mar 2018 22:52:21 +0000 (08:52 +1000)]
Merge branch 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few more fixes for 4.16. Mostly for displays:
- A fix for DP handling on radeon
- Fix banding on eDP panels
- Fix HBR audio
- Fix for disabling VGA mode on Raven that leads to a corrupt or
blank display on some platforms
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/display: Add one to EDID's audio channel count when passing to DC
drm/amd/display: We shouldn't set format_default on plane as atomic driver
drm/amd/display: Fix FMT truncation programming
drm/amd/display: Allow truncation to 10 bits
drm/amd/display: fix dereferencing possible ERR_PTR()
drm/amd/display: Refine disable VGA
drm/amdgpu: Use atomic function to disable crtcs with dc enabled
drm/radeon: Don't turn off DP sink when disconnected
David S. Miller [Wed, 21 Mar 2018 22:12:46 +0000 (18:12 -0400)]
Merge branch 'net-sched-action-idr-leak'
Davide Caratti says:
====================
fix idr leak in actions
This series fixes situations where a temporary failure to install a TC
action results in the permanent impossibility to reuse the configured
value of 'index'.
Thanks to Cong Wang for the initial review.
v2: fix build error in act_ipt.c, reported by kbuild test robot
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:28 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_skbmod_init()
tcf_skbmod_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure skbmod rules
using the same idr value will systematically fail with -ENOSPC, unless
the first attempt was done using the 'replace' keyword:
# tc action add action skbmod swap mac index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_skbmod_init(), ensuring that tcf_idr_release() is called
on the error path when the idr has been reserved, but not yet inserted.
Also, don't test 'ovr' in the error path, to avoid a 'replace' failure
implicitly become a 'delete' that leaks refcount in act_skbmod module:
# rmmod act_skbmod; modprobe act_skbmod
# tc action add action skbmod swap mac index 100
# tc action add action skbmod swap mac continue index 100
RTNETLINK answers: File exists
We have an error talking to the kernel
# tc action replace action skbmod swap mac continue index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action skbmod
#
# rmmod act_skbmod
rmmod: ERROR: Module act_skbmod is in use
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:27 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_vlan_init()
tcf_vlan_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure vlan rules using
the same idr value will systematically fail with -ENOSPC, unless the first
attempt was done using the 'replace' keyword.
# tc action add action vlan pop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_vlan_init(), ensuring that tcf_idr_release() is called on
the error path when the idr has been reserved, but not yet inserted. Also,
don't test 'ovr' in the error path, to avoid a 'replace' failure implicitly
become a 'delete' that leaks refcount in act_vlan module:
# rmmod act_vlan; modprobe act_vlan
# tc action add action vlan push id 5 index 100
# tc action replace action vlan push id 7 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action vlan
#
# rmmod act_vlan
rmmod: ERROR: Module act_vlan is in use
Fixes: 4c5b9d9642c8 ("act_vlan: VLAN action rewrite to use RCU lock/unlock and update") Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:26 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of __tcf_ipt_init()
__tcf_ipt_init() can fail after the idr has been successfully reserved.
When this happens, subsequent attempts to configure xt/ipt rules using
the same idr value systematically fail with -ENOSPC:
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of __tcf_ipt_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup(). Since tcf_ipt_release() can now be called
when tcfi_t is NULL, we also need to protect calls to ipt_destroy_target()
to avoid NULL pointer dereference.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:25 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcp_pedit_init()
tcf_pedit_init() can fail to allocate 'keys' after the idr has been
successfully reserved. When this happens, subsequent attempts to configure
a pedit rule using the same idr value systematically fail with -ENOSPC:
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of tcf_act_pedit_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 21 Mar 2018 22:12:07 +0000 (15:12 -0700)]
libnvdimm, nfit: fix persistence domain reporting
The persistence domain is a point in the platform where once writes
reach that destination the platform claims it will make them persistent
relative to power loss. In the ACPI NFIT this is currently communicated
as 2 bits in the "NFIT - Platform Capabilities Structure". The bits
comprise a hierarchy, i.e. bit0 "CPU Cache Flush to NVDIMM Durability on
Power Loss Capable" implies bit1 "Memory Controller Flush to NVDIMM
Durability on Power Loss Capable".
Commit 96c3a239054a "libnvdimm: expose platform persistence attr..."
shows the persistence domain as flags, but it's really an enumerated
hierarchy.
Fix this newly introduced user ABI to show the closest available
persistence domain before userspace develops dependencies on seeing, or
needing to develop code to tolerate, the raw NFIT flags communicated
through the libnvdimm-generic region attribute.
Fixes: 96c3a239054a ("libnvdimm: expose platform persistence attr...") Reviewed-by: Dave Jiang <dave.jiang@intel.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
projects / mirror_ubuntu-eoan-kernel.git / log