Miquel Raynal [Fri, 16 Jun 2023 13:45:53 +0000 (15:45 +0200)]
can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs
In their RZN1 SoC, Renesas put a CAN controller supposed to act very
similarly to the original Philips sja1000. In practice, while flooding
the bus with another device, we discovered that the controller very
often after an overrun situation would just refuse any new frame, drop
them all and trigger over and over again the overrun interrupt, even
though the buffer would have been totally emptied. The controller acts
like if its internal buffer offsets (where it writes and where the host
reads) where totally screwed-up.
Renesas manual mentions a single action to perform in order to
resynchronize the read and write offsets within the buffer: performing
a soft reset.
Performing a soft reset takes a bit of time and involves small delays,
so better do that in a threaded handler rather than inside the hard IRQ
handler.
Add platform data to recognize the platforms which need this workaround,
and when the faulty situation is diagnosed, stop what is being
performed and request the threaded handler to be executed in order to
perform the reset.
Miquel Raynal [Fri, 16 Jun 2023 13:45:52 +0000 (15:45 +0200)]
can: sja1000: Prepare the use of a threaded handler
In order to support a flavor of the sja1000 which sometimes freezes, it
will be needed upon certain interrupts to perform a soft reset. The soft
reset operation takes a bit of time, so better not do it within the hard
interrupt handler but rather in a threaded handler. Let's prepare the
possibility for sja1000_err() to request "interrupting" the current flow
and request the threaded handler to be run while keeping the interrupt
line low.
Merge patch series "can: esd_usb: More preparation before supporting esd CAN-USB/3 (addendum)"
Frank Jungclaus <frank.jungclaus@esd.eu> says:
While trying to again merge my code changes for CAN-USB/3, I came
across some more places where it could make sense to change them
analogous to the previous clean-up patch series [1].
Merge patch series "can: esd_usb: More preparation before supporting esd CAN-USB/3"
Frank Jungclaus <frank.jungclaus@esd.eu> says:
Apply another small batch of patches as preparation for adding support
of the newly available esd CAN-USB/3 to esd_usb.c.
v1 -> v2:
* Make use of GENMASK() macro for ESD_USB_NO_BAUDRATE and
ESD_USB_IDMASK
* Also use the BIT() macro for ESD_USB2_3_SAMPLES
* Removed comments with redundant hexadecimal values from
BIT()-constants
* Reworded (shortened) the commit messages
* Changed the macro ESD_USB_3_SAMPLES to ESD_USB_TRIPLE_SAMPLES
Frank Jungclaus [Fri, 19 May 2023 19:56:00 +0000 (21:56 +0200)]
can: esd_usb: Don't bother the user with nonessential log message
Replace a netdev_info(), emitting an informational message about the
BTR value to be send to the controller, with a debug message by means
of netdev_dbg().
Frank Jungclaus [Fri, 19 May 2023 19:55:59 +0000 (21:55 +0200)]
can: esd_usb: Replace hardcoded message length given to USB commands
Replace all hardcoded values supplied to the len element of
esd_usb_msg (and its siblings) by more readable expressions, based on
sizeof(), offsetof(), etc.
Also spend documentation / comments that the len element of esd_usb_msg
is in multiples of 32bit words and not in bytes.
Frank Jungclaus [Fri, 19 May 2023 19:55:58 +0000 (21:55 +0200)]
can: esd_usb: Prefix all structures with the device name
Prefix all the structures with the device name.
For commonly used structures make use of (the module name) esd_usb_.
For esd CAN-USB/2 and CAN-USB/Micro specific structures use
esd_usb_2_ and esd_usb_m.
Frank Jungclaus [Fri, 19 May 2023 19:55:57 +0000 (21:55 +0200)]
can: esd_usb: Use consistent prefixes for macros
Add the consistent prefix ESD_USB_ to all macros defined within
esd_usb.c.
For macros specific to esd CAN-USB/2 use ESD_USB_2_ as prefix.
For macros specific to esd CAN-USB/Micro use ESD_USB_M_ as prefix.
Change the macro ESD_USB_3_SAMPLES to ESD_USB_TRIPLE_SAMPLES to not
mix up with the prefix ESD_USB_3_ which will be introduced for the
CAN-USB/3 device.
Frank Jungclaus [Fri, 19 May 2023 19:55:56 +0000 (21:55 +0200)]
can: esd_usb: Replace initializer macros used for struct can_bittiming_const
Replace the macros used to initialize the members of struct
can_bittiming_const with direct values. Then also use those struct
members to do the calculations in esd_usb2_set_bittiming().
Frank Jungclaus [Fri, 19 May 2023 19:55:55 +0000 (21:55 +0200)]
can: esd_usb: Make use of existing kernel macros
Make use of existing kernel macros:
- Use the unit suffixes from linux/units.h for the controller clock
frequencies
- Use the BIT() and the GENMASK() macro to set specific bits in some
constants
- Use CAN_MAX_DLEN (instead of directly using the value 8) for the
maximum CAN payload length
Additionally:
- Spend some commenting for the previously changed constants
- Add the current year to the copyright notice
- While adding the header linux/units.h to the list of include files
also sort that list alphabetically
can: dev: add transceiver capabilities to xilinx_can
Currently the xilinx_can driver does not support adding a phy like the
"ti,tcan1043" to its devicetree.
This code makes it possible to add such phy, so that the kernel makes
sure that the PHY is in operational state, when the link is set to an
"up" state.
Signed-off-by: Marcel Hellwig <git@cookiesoft.de> Link: https://lore.kernel.org/r/20230417085204.179268-1-git@cookiesoft.de
[mkl: call phy_power_off() after pm_runtime_put()]
[mkl: remove error message for phy_power_on() failure]
[mkl: update kernel-doc for struct xcan_priv] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Mon, 22 May 2023 11:44:44 +0000 (12:44 +0100)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: allow matching on meta data
Michal Swiatkowski says:
This patchset is intended to improve the usability of the switchdev
slow path. Without matching on a meta data values slow path works
based on VF's MAC addresses. It causes a problem when the VF wants
to use more than one MAC address (e.g. when it is in trusted mode).
Parse all meta data in the same place where protocol type fields are
parsed. Add description for the currently implemented meta data. It is
important to note that depending on DDP not all described meta data can
be available. Using not available meta data leads to error returned by
function which is looking for correct words in profiles read from DDP.
There is also one small improvement, remove of rx field in rule info
structure (patch 2). It is redundant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Sat, 20 May 2023 17:21:04 +0000 (19:21 +0200)]
nfc: Switch i2c drivers back to use .probe()
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Begunkov [Fri, 19 May 2023 13:30:36 +0000 (14:30 +0100)]
net/tcp: refactor tcp_inet6_sk()
Don't keep hand coded offset caluclations and replace it with
container_of(). It should be type safer and a bit less confusing.
It also makes it with a macro instead of inline function to preserve
constness, which was previously casted out like in case of
tcp_v6_send_synack().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 19 May 2023 13:03:59 +0000 (14:03 +0100)]
net: phy: add helpers for comparing phy IDs
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: altera: tse: remove mac_an_restart() function
The mac_an_restart() method will only be called if the driver sets
legacy_pre_march2020, which the altera tse driver does not do.
Therefore, providing a stub is unnecessary.
Fixes: fef2998203e1 ("net: altera: tse: convert to phylink") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 19 May 2023 09:32:38 +0000 (11:32 +0200)]
net: ipconfig: move ic_nameservers_fallback into #ifdef block
The new variable is only used when IPCONFIG_BOOTP is defined and otherwise
causes a warning:
net/ipv4/ipconfig.c:177:12: error: 'ic_nameservers_fallback' defined but not used [-Werror=unused-variable]
Move it next to the user.
Fixes: 81ac2722fa19 ("net: ipconfig: Allow DNS to be overwritten by DHCPACK") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Fang [Fri, 19 May 2023 02:01:13 +0000 (10:01 +0800)]
net: fec: remove useless fec_enet_reset_skb()
This patch is a cleanup for fec driver. The fec_enet_reset_skb()
is used to free skb buffers for tx queues and is only invoked in
fec_restart(). However, fec_enet_bd_init() also resets skb buffers
and is invoked in fec_restart() too. So fec_enet_reset_skb() is
redundant and useless.
Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Fang [Fri, 19 May 2023 01:48:25 +0000 (09:48 +0800)]
net: fec: turn on XDP features
The XDP features are supported since the commit 66c0e13ad236
("drivers: net: turn on XDP features"). Currently, the fec
driver supports NETDEV_XDP_ACT_BASIC, NETDEV_XDP_ACT_REDIRECT
and NETDEV_XDP_ACT_NDO_XMIT. So turn on these XDP features
for fec driver.
Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a source MAC to direct packets from the VF to the corresponding
port representor is only ok if there is only one MAC on a VF. To support
this functionality when the number of MACs on a VF is greater, it is
necessary to match a source VSI instead of a source MAC.
Let's use the new switch API that allows matching on metadata.
If MAC isn't used in match criteria there is no need to handle adding
rule after virtchnl command. Instead add new rule while port representor
is being configured.
Remove rule_added field, checking for sp_rule can be used instead.
Remove also checking for switchdev running in deleting rule as it can be
called from unroll context when running flag isn't set. Checking for
sp_rule covers both context (with and without running flag).
Rules are added in eswitch configuration flow, so there is no need to
have replay function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add meta data matching criteria in the same place as protocol matching
criteria. There is no need to add meta data as special words after
parsing all lookups. Trade meta data in the same why as other lookups.
The one difference between meta data lookups and protocol lookups is
that meta data doesn't impact how the packets looks like. Because of that
ignore it when filling testing packet.
Match on tunnel type meta data always if tunnel type is different than
TNL_LAST.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Anonymous initializers are now discouraged. Define ICE_PROTCOL_ENTRY
macro to rewrite anonymous initializers to named one. No functional
changes here.
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Information about the direction is currently stored in sw_act.flag.
There is no need to duplicate it in another field.
Setting direction flag doesn't mean that there is a match criteria for
direction in rule. It is only a information for HW from where switch id
should be collected (VSI or port). In current implementation of advance
rule handling, without matching for direction meta data, we can always
set one the same flag and everything will work the same.
Ability to match on direction meta data will be added in follow up
patches.
Recipe 0, 3 and 9 loaded from package has direction match
criteria, but they are handled in other function.
Move ice_adv_rule_info fields to avoid holes.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add description for each meta data. Redefine tunnel mask to match only
tunneled MAC and tunneled VLAN. It shouldn't try to match other flags
(previously it was 0xff, it is redundant).
VLAN mask was 0xd000, change it to 0xf000. 4 last bits are flags
depending on the same field in packets (VLAN tag). Because of that,
It isn't harmful to match also on ITAG.
Group all MDID and MDID offsets into enums to keep things organized.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Uwe Kleine-König [Thu, 18 May 2023 20:30:49 +0000 (22:30 +0200)]
net: arc: Make arc_emac_remove() return void
The function returns zero unconditionally. Change it to return void instead
which simplifies its callers as error handing becomes unnecessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mptcp: Refactor inet_accept() and MIB updates
Patches 1 and 2 refactor inet_accept() to provide a new __inet_accept()
that's usable with locked sockets, and then make use of that helper to
simplify mptcp_stream_accept().
Patches 3 and 4 add some new MIBS related to MPTCP address advertisement
and update related selftest scripts.
Patch 5 modifies the selftests to ensure MIBS are only printed once when
a test case fails.
====================
Paolo Abeni [Wed, 17 May 2023 19:16:16 +0000 (12:16 -0700)]
mptcp: introduces more address related mibs
Currently we don't track explicitly a few events related to address
management suboption handling; this patch adds new mibs for ADD_ADDR
and RM_ADDR options tx and for missed tx events due to internal storage
exhaustion.
The self-tests must be updated to properly handle different mibs with
the same/shared prefix.
Additionally removes a couple of warning tracking the loss event.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/378 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 19 May 2023 03:04:59 +0000 (20:04 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-05-17 (ice, MAINTAINERS)
This series contains updates to ice driver and MAINTAINERS file.
Paul refactors PHY to link mode reporting and updates some PHY types to
report more accurate link modes for ice.
Dave removes mutual exclusion policy between LAG and SR-IOV in ice
driver.
Jesse updates link for Intel Wired LAN in the MAINTAINERS file.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
MAINTAINERS: update Intel Ethernet links
ice: Remove LAG+SRIOV mutual exclusion
ice: update PHY type to ethtool link mode mapping
ice: refactor PHY type to ethtool link mode
ice: update ICE_PHY_TYPE_HIGH_MAX_INDEX
====================
====================
net: sfp: add support for control of rate selection
This series introduces control of the rate selection SFP pins (or
their soft state in the I2C diagnostics EEPROM). Several SNIA documents
(referenced in the commits) describe the various different modes for
these, and we implement them all for maximum compatibility, but as
we know, SFP modules tend to do their own thing, so that may not be
sufficient.
In order to implement this, we need to change the locking arrangement
in the SFP layer - we need to make st_mutex (state mutex) able to be
taken from within the rtnl lock and sm_mutex (state machine mutex).
Essentially, st_mutex protects the hard (gpio) and soft state signals.
So, patches 2 through 5 rejig the locking so that st_mutex is only
ever taken when we want to fiddle with the signal state variables,
read or write the GPIOs, or read or write the soft state.
Patch 1 adds a helper that makes the locking rejig a little easier
as it combines the update of sfp->state with setting the updated
control state to the module.
Patch 6 adds code to phylink to give the signalling rate for various
PHY interface modes that are relevant to SFPs - this is the baud rate
of the encoded signal, not the data rate, which is what matters for
SFPs. This rate is passed through the SFP bus layer into the SFP
socket driver, which initially has a stub sfp_set_signal_rate().
Patch 7 adds the code to the SFP socket driver to parse the rate
selection data in the EEPROM, configure which RS signals need to be
driven, and the signalling rate threshold. We fill in
sfp_set_signal_rate() to set the rate select pins as appropriate.
====================
Add support for parsing the rate select thresholds and switching of the
RS0 and RS1 signals to the transceiver. This is complicated by various
revisions of SFF-8472 and interaction of SFF-8431, SFF-8079 and
INF-8074.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to the SFP layer to allow phylink to set the signalling
rate for a SFP module. The rate given will be in units of kilo-baud
(1000 baud).
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change st_mutex's use within SFP such that it only protects the various
state members, as it was originally supposed to, and isn't held while
making various calls outside the driver.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide an unlocked version of sfp_sm_event() which can be used by
sfp_check_state() to avoid having to keep re-taking the lock if
several signals have changed state.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Swap the order of the rtnl and st_mutex locks - st_mutex is now nested
beneath rtnl lock instead of rtnl being beneath st_mutex. This will
allow us to hold st_mutex only while manipulating the module's hardware
or software control state.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As preparation to moving st_mutex inside rtnl_lock, we need to first
move the rtnl lock to cover reading the state.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a couple of locations in the code where we modify
sfp->state, and then call sfp_set_state(, sfp->state) to update
the outputs/soft state to control the module. Provide a helper
which takes a mask and new state so that this is encapsulated in
one location.
Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/freescale/fec_main.c 6ead9c98cafc ("net: fec: remove the xdp_return_frame when lack of tx BDs") 144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Jakub Kicinski [Thu, 18 May 2023 21:05:48 +0000 (14:05 -0700)]
Merge tag 'nf-next-2023-05-18' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
Netfilter updates for net-next
nftables updates:
1. Allow key existence checks with maps.
At the moment the kernel requires userspace to pass a destination
register for the associated value, make this optional so userspace
can query if the key exists, just like with normal sets.
2. nftables maintains a counter per set that holds the number of
elements. This counter gets decremented on element removal,
but its only incremented if the set has a upper maximum value.
Increment unconditionally, this will allow us to update the
maximum value later on.
3. At DCCP option maching, from Jeremy Sowden.
4. use struct_size macro, from Christophe JAILLET.
Conntrack:
5. Squash holes in struct nf_conntrack_expect, also Christophe JAILLET.
6. Allow clash resolution for GRE Protocol to avoid a packet drop,
from Faicker Mo.
Flowtable:
Simplify route logic and split large functions into smaller
chunks, from Pablo Neira Ayuso.
* tag 'nf-next-2023-05-18' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: flowtable: split IPv6 datapath in helper functions
netfilter: flowtable: split IPv4 datapath in helper functions
netfilter: flowtable: simplify route logic
netfilter: conntrack: allow insertion clash of gre protocol
netfilter: nft_set_pipapo: Use struct_size()
netfilter: Reorder fields in 'struct nf_conntrack_expect'
netfilter: nft_exthdr: add boolean DCCP option matching
netfilter: nf_tables: always increment set element count
netfilter: nf_tables: relax set/map validation checks
====================
Baozhu Ni [Wed, 17 May 2023 01:27:26 +0000 (09:27 +0800)]
e1000e: Add @adapter description to kdoc
Provide a description for the kernel doc of the @adapter
of e1000e_trigger_lsc()
Signed-off-by: Baozhu Ni <nibaozhu@yeah.net> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tom Rix [Fri, 28 Apr 2023 20:00:09 +0000 (16:00 -0400)]
igb: Define igb_pm_ops conditionally on CONFIG_PM
For s390, gcc with W=1 reports
drivers/net/ethernet/intel/igb/igb_main.c:186:32: error:
'igb_pm_ops' defined but not used [-Werror=unused-const-variable=]
186 | static const struct dev_pm_ops igb_pm_ops = {
| ^~~~~~~~~~
The only use of igb_pm_ops is conditional on CONFIG_PM.
The definition of igb_pm_ops should also be conditional on CONFIG_PM
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Kurt Kanzenbach [Wed, 12 Apr 2023 07:36:11 +0000 (09:36 +0200)]
igc: Avoid transmit queue timeout for XDP
High XDP load triggers the netdev watchdog:
|NETDEV WATCHDOG: enp3s0 (igc): transmit queue 2 timed out
The reason is the Tx queue transmission start (txq->trans_start) is not updated
in XDP code path. Therefore, add it for all XDP transmission functions.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- eth: hns3: fix sending pfc frames after reset issue
Previous releases - always broken:
- xfrm: release all offloaded policy memory
- nsh: use correct mac_offset to unwind gso skb in nsh_gso_segment()
- vsock: avoid to close connected socket after the timeout
- dsa: rzn1-a5psw: enable management frames for CPU port
- eth: virtio_net: fix error unwinding of XDP initialization
- eth: tun: fix memory leak for detached NAPI queue.
Misc:
- MAINTAINERS: sctp: move Neil to CREDITS"
* tag 'net-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits)
MAINTAINERS: skip CCing netdev for Bluetooth patches
mdio_bus: unhide mdio_bus_init prototype
bridge: always declare tunnel functions
atm: hide unused procfs functions
net: isa: include net/Space.h
Revert "ARM: dts: stm32: add CAN support on stm32f746"
netfilter: nft_set_rbtree: fix null deref on element insertion
netfilter: nf_tables: fix nft_trans type confusion
netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with CONFIG_NF_NAT
net: wwan: t7xx: Ensure init is completed before system sleep
net: selftests: Fix optstring
net: pcs: xpcs: fix C73 AN not getting enabled
net: wwan: iosm: fix NULL pointer dereference when removing device
vlan: fix a potential uninit-value in vlan_dev_hard_start_xmit()
mailmap: add entries for Nikolay Aleksandrov
igb: fix bit_shift to be in [1..8] range
net: dsa: mv88e6xxx: Fix mv88e6393x EPC write command offset
cassini: Fix a memory leak in the error handling path of cas_init_one()
tun: Fix memory leak for detached NAPI queue.
can: kvaser_pciefd: Disable interrupts in probe error path
...
- improve error handling in dw2102 if it can't retrieve DVB MAC
address"
* tag 'media/v6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb-core: Fix use-after-free due to race condition at dvb_ca_en50221
media: dvb-core: Fix kernel WARNING for blocking operation in wait_event*()
media: dvb-core: Fix use-after-free due to race at dvb_register_device()
media: dvb-core: Fix use-after-free due on race condition at dvb_net
media: dvb-core: Fix use-after-free on race condition at dvb_frontend
media: mn88443x: fix !CONFIG_OF error by drop of_match_ptr from ID table
media: ttusb-dec: fix memory leak in ttusb_dec_exit_dvb()
media: dvb_ca_en50221: fix a size write bug
media: netup_unidvb: fix irq init by register it at the end of probe
media: dvb-usb: dw2102: fix uninit-value in su3000_read_mac_address
media: dvb-usb: digitv: fix null-ptr-deref in digitv_i2c_xfer()
media: dvb-usb-v2: rtl28xxu: fix null-ptr-deref in rtl28xxu_i2c_xfer
media: dvb-usb-v2: ce6230: fix null-ptr-deref in ce6230_i2c_master_xfer()
media: dvb-usb-v2: ec168: fix null-ptr-deref in ec168_i2c_xfer()
media: dvb-usb: az6027: fix three null-ptr-deref in az6027_i2c_xfer()
media: netup_unidvb: fix use-after-free at del_timer()
media: dvb_demux: fix a bug for the continuity counter
media: pvrusb2: fix DVB_CORE dependency
====================
net: lan966x: Add support for PCP, DEI, DSCP
This patch series extends lan966x to offload to the hardware the
following features:
- PCP: this configuration is per port both at ingress and egress.
- App trust: which allows to specify a trust order of app selectors.
This can be PCP or DSCP or DSCP/PCP.
- default priority
- DSCP: this configuration is shared between the ports both at ingress
and egress.
====================
Horatiu Vultur [Tue, 16 May 2023 20:14:08 +0000 (22:14 +0200)]
net: lan966x: Add support for DSCP rewrite
Add support for DSCP rewrite in lan966x driver. On egress DSCP is
rewritten from either classified DSCP, or frame DSCP. Classified DSCP is
determined by the Analyzer Classifier on ingress, and is mapped from
classified QoS class and DP level. Classification of DSCP is by default
enabled for all ports.
It is required that DSCP is trusted for the egress port *and* rewrite
table is not empty, in order to rewrite DSCP based on classified DSCP,
otherwise DSCP is always rewritten from frame DSCP.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Horatiu Vultur [Tue, 16 May 2023 20:14:07 +0000 (22:14 +0200)]
net: lan966x: Add support for PCP rewrite
Add support for rewrite of PCP and DEI value, based on QoS and DP level.
The DCB rewrite table is queried for mappings between priority and
PCP/DEI. The classified DP level is then encoded in the DEI bit, if a
mapping for DEI exists.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 18 May 2023 09:06:28 +0000 (11:06 +0200)]
Merge tag 'linux-can-fixes-for-6.4-20230518' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2023-05-18
this is a pull request of 7 patches for net/master.
The first 6 patches are by Jimmy Assarsson and fix several bugs in the
kvaser_pciefd driver.
The latest patch is from me and reverts a change in stm32f746.dtsi
that causes build errors due to a missing dependent patch.
* tag 'linux-can-fixes-for-6.4-20230518' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
Revert "ARM: dts: stm32: add CAN support on stm32f746"
can: kvaser_pciefd: Disable interrupts in probe error path
can: kvaser_pciefd: Do not send EFLUSH command on TFD interrupt
can: kvaser_pciefd: Empty SRB buffer in probe
can: kvaser_pciefd: Call request_irq() before enabling interrupts
can: kvaser_pciefd: Clear listen-only bit if not explicitly requested
can: kvaser_pciefd: Set CAN_STATE_STOPPED in kvaser_pciefd_stop()
====================
Faicker Mo [Sun, 23 Apr 2023 02:29:57 +0000 (10:29 +0800)]
netfilter: conntrack: allow insertion clash of gre protocol
NVGRE tunnel is used in the VM-to-VM communications. The VM packets
are encapsulated in NVGRE and sent from the host. For NVGRE
there are two tuples(outer sip and outer dip) in the host conntrack item.
Insertion clashes are more likely to happen if the concurrent connections
are sent from the VM.
Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn> Signed-off-by: Florian Westphal <fw@strlen.de>
The xt_dccp iptables module supports the matching of DCCP packets based
on the presence or absence of DCCP options. Extend nft_exthdr to add
this functionality to nftables.
Florian Westphal [Thu, 11 May 2023 20:45:35 +0000 (22:45 +0200)]
netfilter: nf_tables: always increment set element count
At this time, set->nelems counter only increments when the set has
a maximum size.
All set elements decrement the counter unconditionally, this is
confusing.
Increment the counter unconditionally to make this symmetrical.
This would also allow changing the set maximum size after set creation
in a later patch.
Jakub Kicinski [Thu, 18 May 2023 04:43:20 +0000 (21:43 -0700)]
Merge tag 'nf-23-05-17' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
Netfilter fixes for net
1. Silence warning about unused variable when CONFIG_NF_NAT=n, from Tom Rix.
2. nftables: Fix possible out-of-bounds access, from myself.
3. nftables: fix null deref+UAF during element insertion into rbtree,
also from myself.
* tag 'nf-23-05-17' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_set_rbtree: fix null deref on element insertion
netfilter: nf_tables: fix nft_trans type confusion
netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with CONFIG_NF_NAT
====================
Jakub Kicinski [Thu, 18 May 2023 04:36:21 +0000 (21:36 -0700)]
Merge tag 'wireless-2023-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.4
A lot of fixes this time, for both the stack and the drivers. The
brcmfmac resume fix has been reported by several people so I would say
it's the most important here. The iwlwifi RFI workaround is also
something which was reported as a regression recently.
* tag 'wireless-2023-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (31 commits)
wifi: b43: fix incorrect __packed annotation
wifi: rtw88: sdio: Always use two consecutive bytes for word operations
mac80211_hwsim: fix memory leak in hwsim_new_radio_nl
wifi: iwlwifi: mvm: Add locking to the rate read flow
wifi: iwlwifi: Don't use valid_links to iterate sta links
wifi: iwlwifi: mvm: don't trust firmware n_channels
wifi: iwlwifi: mvm: fix OEM's name in the tas approved list
wifi: iwlwifi: fix OEM's name in the ppag approved list
wifi: iwlwifi: mvm: fix initialization of a return value
wifi: iwlwifi: mvm: fix access to fw_id_to_mac_id
wifi: iwlwifi: fw: fix DBGI dump
wifi: iwlwifi: mvm: fix number of concurrent link checks
wifi: iwlwifi: mvm: fix cancel_delayed_work_sync() deadlock
wifi: iwlwifi: mvm: don't double-init spinlock
wifi: iwlwifi: mvm: always free dup_data
wifi: mac80211: recalc chanctx mindef before assigning
wifi: mac80211: consider reserved chanctx for mindef
wifi: mac80211: simplify chanctx allocation
wifi: mac80211: Abort running color change when stopping the AP
wifi: mac80211: fix min center freq offset tracing
...
====================
Arnd Bergmann [Tue, 16 May 2023 19:45:36 +0000 (21:45 +0200)]
mdio_bus: unhide mdio_bus_init prototype
mdio_bus_init() is either used as a local module_init() entry,
or it gets called in phy_device.c. In the former case, there
is no declaration, which causes a warning:
drivers/net/phy/mdio_bus.c:1371:12: error: no previous prototype for 'mdio_bus_init' [-Werror=missing-prototypes]
Remove the #ifdef around the declaration to avoid the warning..
Arnd Bergmann [Tue, 16 May 2023 19:45:35 +0000 (21:45 +0200)]
bridge: always declare tunnel functions
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, two functions are still
defined but have no prototype or caller. This causes a W=1 warning for
the missing prototypes:
net/bridge/br_netlink_tunnel.c:29:6: error: no previous prototype for 'vlan_tunid_inrange' [-Werror=missing-prototypes]
net/bridge/br_netlink_tunnel.c:199:5: error: no previous prototype for 'br_vlan_tunnel_info' [-Werror=missing-prototypes]
The functions are already contitional on CONFIG_BRIDGE_VLAN_FILTERING,
and I coulnd't easily figure out the right set of #ifdefs, so just
move the declarations out of the #ifdef to avoid the warning,
at a small cost in code size over a more elaborate fix.
Fixes: 188c67dd1906 ("net: bridge: vlan options: add support for tunnel id dumping") Fixes: 569da0822808 ("net: bridge: vlan options: add support for tunnel mapping set/del") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230516194625.549249-3-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Tue, 16 May 2023 19:45:34 +0000 (21:45 +0200)]
atm: hide unused procfs functions
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Arnd Bergmann [Tue, 16 May 2023 19:45:33 +0000 (21:45 +0200)]
net: isa: include net/Space.h
The legacy drivers that still get called from net/Space.c have prototypes
in net/Space, but this header is not included in most of the files that
define those functions:
drivers/net/ethernet/cirrus/cs89x0.c:1649:28: error: no previous prototype for 'cs89x0_probe' [-Werror=missing-prototypes]
drivers/net/ethernet/8390/ne.c:947:28: error: no previous prototype for 'ne_probe' [-Werror=missing-prototypes]
drivers/net/ethernet/8390/smc-ultra.c:167:28: error: no previous prototype for 'ultra_probe' [-Werror=missing-prototypes]
drivers/net/ethernet/amd/lance.c:438:28: error: no previous prototype for 'lance_probe' [-Werror=missing-prototypes]
drivers/net/ethernet/3com/3c515.c:422:20: error: no previous prototype for 'tc515_probe' [-Werror=missing-prototypes]
mlxfw: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
Zero-length arrays are deprecated and we are moving towards adopting
C99 flexible-array members, instead. So, replace zero-length arrays
declarations alone in structs with the new DECLARE_FLEX_ARRAY()
helper macro.
This helper allows for flexible-array members alone in structs.
The commit 0920ccdf41e3 ("ARM: dts: stm32: add CAN support on
stm32f746") depends on the patch "dt-bindings: mfd: stm32f7: add
binding definition for CAN3" [1], which is not in net/main, yet. This
results in a parsing error of "stm32f746.dtsi".
Linus Torvalds [Wed, 17 May 2023 18:16:36 +0000 (11:16 -0700)]
Merge tag 'linux-kselftest-fixes-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- sgx test fix for false negatives
- ftrace output is hard to parses and it masks inappropriate skips etc.
This fix addresses the problems by integrating with kselftest runner
* tag 'linux-kselftest-fixes-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/ftrace: Improve integration with kselftest runner
selftests/sgx: Add "test_encl.elf" to TEST_FILES
Linus Torvalds [Wed, 17 May 2023 16:56:01 +0000 (09:56 -0700)]
Merge tag 'nfsd-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- A collection of minor bug fixes
* tag 'nfsd-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Remove open coding of string copy
SUNRPC: Fix trace_svc_register() call site
SUNRPC: always free ctxt when freeing deferred request
SUNRPC: double free xprt_ctxt while still in use
SUNRPC: Fix error handling in svc_setup_socket()
SUNRPC: Fix encoding of accepted but unsuccessful RPC replies
lockd: define nlm_port_min,max with CONFIG_SYSCTL
nfsd: define exports_proc_ops with CONFIG_PROC_FS
SUNRPC: Avoid relying on crypto API to derive CBC-CTS output IV
Linus Torvalds [Wed, 17 May 2023 16:49:21 +0000 (09:49 -0700)]
Merge tag 'tpmdd-v6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"Three bug fixes for recently discovered issues"
* tag 'tpmdd-v6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm/tpm_tis: Disable interrupts for more Lenovo devices
tpm: Prevent hwrng from activating during resume
tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resume
Arnd Bergmann [Wed, 17 May 2023 12:47:12 +0000 (14:47 +0200)]
tracing: make ftrace_likely_update() declaration visible
This function is only used when CONFIG_TRACE_BRANCH_PROFILING is set and
DISABLE_BRANCH_PROFILING is not set, and the declaration is hidden
behind this combination of tests.
But that causes a warning when building with CONFIG_TRACING_BRANCHES,
since that sets DISABLE_BRANCH_PROFILING for the tracing code, and the
declaration is thus hidden:
kernel/trace/trace_branch.c:205:6: error: no previous prototype for 'ftrace_likely_update' [-Werror=missing-prototypes]
Move the declaration out of the #ifdef to avoid the warning.
Dave Ertman [Tue, 16 May 2023 11:30:55 +0000 (13:30 +0200)]
ice: Remove LAG+SRIOV mutual exclusion
There was a change previously to stop SR-IOV and LAG from existing on the
same interface. This was to prevent the violation of LACP (Link
Aggregation Control Protocol). The method to achieve this was to add a
no-op Rx handler onto the netdev when SR-IOV VFs were present, thus
blocking bonding, bridging, etc from claiming the interface by adding
its own Rx handler. Also, when an interface was added into a aggregate,
then the SR-IOV capability was set to false.
There are some users that have in house solutions using both SR-IOV and
bridging/bonding that this method interferes with (e.g. creating duplicate
VFs on the bonded interfaces and failing between them when the interface
fails over).
It makes more sense to provide the most functionality
possible, the restriction on co-existence of these features will be
removed. No additional functionality is currently being provided beyond
what existed before the co-existence restriction was put into place. It is
up to the end user to not implement a solution that would interfere with
existing network protocols.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Paul Greenwalt [Wed, 26 Apr 2023 18:50:47 +0000 (11:50 -0700)]
ice: update PHY type to ethtool link mode mapping
Some link modes can be more accurately reported due to newer link mode
values that have been added to the kernel; update those PHY type to report
modes that better reflect the link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Paul Greenwalt [Wed, 26 Apr 2023 18:50:46 +0000 (11:50 -0700)]
ice: refactor PHY type to ethtool link mode
Refactor ice_phy_type_to_ethtool to use phy_type_[low|high]_lkup table to
map PHY type to AQ link speed and ethtool link mode. This removes
complexity and simplifies future changes.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Paul Greenwalt [Wed, 26 Apr 2023 18:50:45 +0000 (11:50 -0700)]
ice: update ICE_PHY_TYPE_HIGH_MAX_INDEX
ICE_PHY_TYPE_HIGH_MAX_INDEX should be the maximum index value and not the
length/number of ICE_PHY_TYPE_HIGH. This is not an issue because this
define is only used when calling ice_get_link_speed_based_on_phy_type(),
which will return ICE_AQ_LINK_SPEED_UNKNOWN for any invalid index. The
caller of ice_get_link_speed_based_on_phy_type(), ice_update_phy_type()
checks that the return value is a valid link speed before using it and
ICE_AQ_LINK_SPEED_UNKNOWN is not. However, update the define to reflect
the correct value.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Florian Westphal [Thu, 11 May 2023 20:39:30 +0000 (22:39 +0200)]
netfilter: nft_set_rbtree: fix null deref on element insertion
There is no guarantee that rb_prev() will not return NULL in nft_rbtree_gc_elem():
general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
nft_add_set_elem+0x14b0/0x2990
nf_tables_newsetelem+0x528/0xb30
Furthermore, there is a possible use-after-free while iterating,
'node' can be free'd so we need to cache the next value to use.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection") Signed-off-by: Florian Westphal <fw@strlen.de>
Florian Westphal [Thu, 11 May 2023 12:15:15 +0000 (14:15 +0200)]
netfilter: nf_tables: fix nft_trans type confusion
nft_trans_FOO objects all share a common nft_trans base structure, but
trailing fields depend on the real object size. Access is only safe after
trans->msg_type check.
Check for rule type first. Found by code inspection.
Tom Rix [Sun, 14 May 2023 14:00:10 +0000 (10:00 -0400)]
netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with CONFIG_NF_NAT
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Florian Westphal <fw@strlen.de>
Some boards use SJA1105 Ethernet Switch with SPI CPHA, while ones with
SJA1110 use SPI CPOL, so document this to fix dtbs_check warnings:
arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dtb: ethernet-switch@0: Unevaluated properties are not allowed ('spi-cpol' was unexpected)
Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jaco Kroon [Wed, 17 May 2023 08:00:03 +0000 (10:00 +0200)]
net/pppoe: make number of hash bits configurable
When running large numbers of pppoe connections, a bucket size of 16 may
be too small and 256 may be more appropriate. This sacrifices some RAM
but should result in faster processing of incoming PPPoE frames.
On our systems we run upwards of 150 PPPoE connections at any point in
time, and we suspect we're starting to see the effects of this small
number of buckets.
The legal values according to pppoe.c is anything that when 8 is divided
by that results in a modulo of 0, ie, 1, 2, 4 and 8.
The size of the per-underlying-interface structure is:
Assuming a 64-bit pointer this will result in just over a 2KiB structure
for PPPOE_HASH_BITS=8, which will likely result in a 4KiB allocation,
which for us at least is acceptable.
Not sure what the minimum allocation size is, and thus if values of 1
and 2 truly make sense. Default results in historic sizing and
behaviour.
Signed-off-by: Jaco Kroon <jaco@uls.co.za> Signed-off-by: David S. Miller <davem@davemloft.net>
Kai-Heng Feng [Wed, 17 May 2023 05:24:51 +0000 (13:24 +0800)]
net: wwan: t7xx: Ensure init is completed before system sleep
When the system attempts to sleep while mtk_t7xx is not ready, the driver
cannot put the device to sleep:
[ 12.472918] mtk_t7xx 0000:57:00.0: [PM] Exiting suspend, modem in invalid state
[ 12.472936] mtk_t7xx 0000:57:00.0: PM: pci_pm_suspend(): t7xx_pci_pm_suspend+0x0/0x20 [mtk_t7xx] returns -14
[ 12.473678] mtk_t7xx 0000:57:00.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1b0 returns -14
[ 12.473711] mtk_t7xx 0000:57:00.0: PM: failed to suspend async: error -14
[ 12.764776] PM: Some devices failed to suspend, or early wake event detected
Mediatek confirmed the device can take a rather long time to complete
its initialization, so wait for up to 20 seconds until init is done.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Tue, 16 May 2023 18:49:24 +0000 (14:49 -0400)]
net: selftests: Fix optstring
The cited commit added a stray colon to the 'v' option. That makes the
option work incorrectly.
ex:
tools/testing/selftests/net# ./fib_nexthops.sh -v
(should enable verbose mode, instead it shows help text due to missing arg)
Fixes: 5feba4727395 ("selftests: fib_nexthops: Make ping timeout configurable") Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log