Alan Stern [Mon, 30 Jun 2014 15:04:21 +0000 (11:04 -0400)]
usb-storage/SCSI: Add broken_fua blacklist flag
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Michael Büsch <m@bues.ch> Tested-by: Michael Büsch <m@bues.ch> Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'fixes-for-v3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.16-rc4
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Lothar Waßmann [Mon, 30 Jun 2014 11:17:27 +0000 (13:17 +0200)]
usb: musb: dsps: fix the base address for accessing the mode register
commit 943c13971c08 "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Cc: stable@vger.kernel.org Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy: msm: Do not do runtime pm if the phy is not idle
Use case is when the phy is configured in host mode and a usb device is
attached to board before bootup. On bootup, with the existing code and
runtime pm enabled, the driver would decrement the pm usage count
without checking the current state of the phy. This pm usage count
decrement would trigger the runtime pm which than would abort the
usb enumeration which was in progress. In my case a usb stick gets
detected and then immediatly the driver goes to low power mode which is
not correct.
log:
[ 1.631412] msm_hsusb_host 12520000.usb: EHCI Host Controller
[ 1.636556] msm_hsusb_host 12520000.usb: new USB bus registered, assigned bus number 1
[ 1.642563] msm_hsusb_host 12520000.usb: irq 220, io mem 0x12520000
[ 1.658197] msm_hsusb_host 12520000.usb: USB 2.0 started, EHCI 1.00
[ 1.659473] hub 1-0:1.0: USB hub found
[ 1.663415] hub 1-0:1.0: 1 port detected
...
[ 1.973352] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[ 2.107707] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.108993] scsi0 : usb-storage 1-1:1.0
[ 2.678341] msm_otg 12520000.phy: USB in low power mode
[ 3.168977] usb 1-1: USB disconnect, device number 2
This issue was detected on IFC6410 board.
This patch fixes the intial runtime pm trigger by checking the phy
state and decrementing the pm use count only when the phy state is IDLE.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Thomas Gleixner [Fri, 20 Jun 2014 21:41:24 +0000 (23:41 +0200)]
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:
CPU 0 CPU1
start_next_transfer(RQ1);
DMA interrupt
if (premature_irq(RQ1))
if (!hrtimer_active(timer))
hrtimer_start(timer);
DMA interrupt
if (premature_irq(RQ2))
if (!hrtimer_active(timer))
hrtimer_start(timer);
timer->state = INACTIVE;
The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:
timer->state != HRTIMER_STATE_INACTIVE
which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.
That's clearly documented:
* A timer is active, when it is enqueued into the rbtree or the
* callback function is running or it's in the state of being migrated
* to another cpu.
But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.
We have a helper function for this: hrtimer_is_queued(). This
evaluates:
timer->state & HRTIMER_STATE_QUEUED
So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().
Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Felipe Balbi <balbi@ti.com>
Andreas Larsson [Thu, 26 Jun 2014 11:07:48 +0000 (13:07 +0200)]
usb: gadget: gr_udc: Fix check for invalid number of microframes
The value 0x3 (not 0x11) in the field for additional transaction/microframe
is reserved and should not be let through. Be clear in the error message about
what value caused the error return.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Ezequiel Garcia [Mon, 23 Jun 2014 18:34:22 +0000 (15:34 -0300)]
usb: musb: Fix panic upon musb_am335x module removal
At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.
On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.
However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.
In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.
Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.
Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:
Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools. Its removel in commit
[ac8dde1: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.
Bring it back so that old user space tools can still be build
without problems on newer kernel versions.
Cc: <stable@vger.kernel.org> # 3.14 Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Reported-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Wang, Yu [Tue, 24 Jun 2014 14:14:44 +0000 (17:14 +0300)]
xhci: Fix runtime suspended xhci from blocking system suspend.
The system suspend flow as following:
1, Freeze all user processes and kenrel threads.
2, Try to suspend all devices.
2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.
2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.
2.3, Call suspend callbacks of devices.
2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.
2.3.2, Finally, hcd_pci_suspend callback is called.
Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.
The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.
For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.
xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.
This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb
"USB: XHCI: resume root hubs when the controller resumes"
Lu Baolu [Tue, 24 Jun 2014 14:14:43 +0000 (17:14 +0300)]
xhci: clear root port wake on bits if controller isn't wake-up capable
When xHCI PCI host is suspended, if do_wakeup is false in xhci_pci_suspend,
xhci_bus_suspend needs to clear all root port wake on bits. Otherwise some Intel
platforms may get a spurious wakeup, even if PCI PME# is disabled.
This patch should be back-ported to kernels as old as 2.6.37, that
contains the commit 9777e3ce907d4cb5a513902a87ecd03b52499569
"USB: xHCI: bus power management implementation".
Mathias Nyman [Tue, 24 Jun 2014 14:14:41 +0000 (17:14 +0300)]
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9519143f06f507dd7cbee6b7a621885
"xhci 1.0: Set transfer burst count field."
Mathias Nyman [Tue, 24 Jun 2014 14:14:40 +0000 (17:14 +0300)]
xhci: Use correct SLOT ID when handling a reset device command
Command completion events normally include command completion status,
SLOT_ID, and a pointer to the original command. Reset device command
completion SLOT_ID may be zero according to xhci specs 4.6.11.
VIA controllers set the SLOT_ID to zero, triggering a WARN_ON in the
command completion handler.
Use the SLOT ID found from the original command instead.
This patch should be applied to stable kernels since 3.13 that contain
the commit 20e7acb13ff48fbc884d5918c3697c27de63922a
"xhci: use completion event's slot id rather than dig it out of command"
Johan Hovold [Sun, 1 Jun 2014 09:32:17 +0000 (11:32 +0200)]
MAINTAINERS: drop two usb-serial subdriver entries
Remove the remaining two obsolete usb-serial subdriver entries from
MAINTAINERS, which were missed in the recent purge by commit f896b7968b62 ("USB: Maintainers change for usb serial drivers").
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Oliver Neukum [Tue, 20 May 2014 14:27:40 +0000 (16:27 +0200)]
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
Reported by Alif Mubarak Ahmad:
This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.
[ johan: style changes ]
Signed-off-by: Oliver Neukum <oneukum@suse.de> Tested-by: Alif Mubarak Ahmad <alive4ever@live.com> Cc: <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
Linus Torvalds [Sun, 22 Jun 2014 05:01:15 +0000 (19:01 -1000)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c new drivers from Wolfram Sang:
"Here is a pull request from i2c hoping for the "new driver" rule.
Originally, I wanted to send this request during the merge window, but
code checkers with very recent additions complained, so a few fixups
were needed. So, some more time went by and I merged rc1 to get a
stable base"
So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c. So I considered not pulling this, but eventually
relented.
Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.
So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6-p2wi: fix call to snprintf
i2c: rk3x: add NULL entry to the end of_device_id array
i2c: sun6i-p2wi: use proper return value in probe
i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
i2c: sunxi: add P2WI DT bindings documentation
i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter
Linus Torvalds [Sun, 22 Jun 2014 02:40:30 +0000 (16:40 -1000)]
Merge tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes
Nothing too earth-shattering here. A fix for a potential regression
due to a patch in pile #1, and the addition of a memory barrier to
prevent a race condition between break_deleg and generic_add_lease"
* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
locks: set fl_owner for leases back to current->files
locks: add missing memory barrier in break_deleg
Linus Torvalds [Sun, 22 Jun 2014 02:38:16 +0000 (16:38 -1000)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"There are three fixes for regressions caused by the relative paths
series: deb-pkg, tar-pkg and *docs did not work with O=.
Plus, there is a fix for the linux-headers deb package and a fixed
typo. These are not regression fixes but are safe enough"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix a typo in a kbuild document
builddeb: fix missing headers in linux-headers package
Documentation: Fix DocBook build with relative $(srctree)
kbuild: Fix tar-pkg with relative $(objtree)
deb-pkg: Fix for relative paths
Linus Torvalds [Sun, 22 Jun 2014 00:21:43 +0000 (14:21 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This fixes some lockups in btrfs reported with rc1. It probably has
some performance impact because it is backing off our spinning locks
more often and switching to a blocking lock. I'll be able to nail
that down next week, but for now I want to get the lockups taken care
of.
Otherwise some more stack reduction and assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong error handle when the device is missing or is not writeable
Btrfs: fix deadlock when mounting a degraded fs
Btrfs: use bio_endio_nodec instead of open code
Btrfs: fix NULL pointer crash when running balance and scrub concurrently
btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
Btrfs: fix broken free space cache after the system crashed
Btrfs: make free space cache write out functions more readable
Btrfs: remove unused wait queue in struct extent_buffer
Btrfs: fix deadlocks with trylock on tree nodes
Linus Torvalds [Sun, 22 Jun 2014 00:20:38 +0000 (14:20 -1000)]
Merge branch 'for-3.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fixes for a new regression from the xdr encoding rewrite, and a
delegation problem we've had for a while (made somewhat more annoying
by the vfs delegation support added in 3.13)"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
NFSD: fix bug for readdir of pseudofs
NFSD: Don't hand out delegations for 30 seconds after recalling them.
Linus Torvalds [Sat, 21 Jun 2014 17:07:17 +0000 (07:07 -1000)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This is larger than usual: the main reason are the ARM symbol lookup
speedups that came in late and were hard to resist.
There's also a kprobes fix and various tooling fixes, plus the minimal
re-enablement of the mmap2 support interface"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/kprobes: Fix build errors and blacklist context_track_user
perf tests: Add test for closing dso objects on EMFILE error
perf tests: Add test for caching dso file descriptors
perf tests: Allow reuse of test_file function
perf tests: Spawn child for each test
perf tools: Add dso__data_* interface descriptons
perf tools: Allow to close dso fd in case of open failure
perf tools: Add file size check and factor dso__data_read_offset
perf tools: Cache dso data file descriptor
perf tools: Add global count of opened dso objects
perf tools: Add global list of opened dso objects
perf tools: Add data_fd into dso object
perf tools: Separate dso data related variables
perf tools: Cache register accesses for unwind processing
perf record: Fix to honor user freq/interval properly
perf timechart: Reflow documentation
perf probe: Improve error messages in --line option
perf probe: Improve an error message of perf probe --vars mode
perf probe: Show error code and description in verbose mode
perf probe: Improve error message for unknown member of data structure
...
Linus Torvalds [Sat, 21 Jun 2014 17:06:02 +0000 (07:06 -1000)]
Merge branch 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rtmutex fixes from Thomas Gleixner:
"Another three patches to make the rtmutex code more robust. That's
the last urgent fallout from the big futex/rtmutex investigation"
* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Plug slow unlock race
rtmutex: Detect changes in the pi lock chain
rtmutex: Handle deadlock detection smarter
Linus Torvalds [Sat, 21 Jun 2014 16:47:01 +0000 (06:47 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Linus Torvalds [Sat, 21 Jun 2014 16:45:54 +0000 (06:45 -1000)]
Merge tag 'for-linus' of git://github.com/gxt/linux
Pull UniCore32 bug fixes from Guan Xuetao:
"This includes bugfixes to make unicore32 successfully build under
defconfig, and some changes for allmodconfig (though not finished)"
* tag 'for-linus' of git://github.com/gxt/linux:
unicore32: Remove ARCH_HAS_CPUFREQ config option
UniCore32: Change git tree location information in MAINTAINERS
arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols
Linus Torvalds [Sat, 21 Jun 2014 16:43:19 +0000 (06:43 -1000)]
Merge tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
Linus Torvalds [Sat, 21 Jun 2014 16:42:40 +0000 (06:42 -1000)]
Merge tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
Linus Torvalds [Sat, 21 Jun 2014 16:41:42 +0000 (06:41 -1000)]
Merge tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
Linus Torvalds [Sat, 21 Jun 2014 16:41:07 +0000 (06:41 -1000)]
Merge tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
Linus Torvalds [Fri, 20 Jun 2014 04:58:57 +0000 (18:58 -1000)]
Merge tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes mostly (ia64 regression related to the ACPI
enumeration of devices, cpufreq regressions, fix for I2C controllers
included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
plus additional kernel command line arguments from Kees to make it
possible to build kernel images with hibernation and the kernel
address space randomization included simultaneously, a new ACPI
battery driver quirk for a system with a broken BIOS and a couple of
ACPI core cleanups.
Specifics:
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver is
built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers included
in BayTrail SoCs are not held in the reset state while they are
being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same time
and to select which of them will be used via the command line (they
are still functionally mutually exclusive, though). From Kees
Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails to
send battery status change notifications timely from Alexander
Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"
* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: mvebu: Fix the name of the states
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
ACPI: use kstrto*() instead of simple_strto*()
ACPI / processor replace __attribute__((packed)) by __packed
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
ACPI / LPSS: Take I2C host controllers out of reset
x86, kaslr: boot-time selectable with hibernation
PM / hibernate: introduce "nohibernate" boot parameter
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
ACPI / ia64 / sba_iommu: Restore the working initialization ordering
Linus Torvalds [Fri, 20 Jun 2014 04:49:37 +0000 (18:49 -1000)]
Merge tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
Linus Torvalds [Fri, 20 Jun 2014 04:40:36 +0000 (18:40 -1000)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This looks bigger than it is, as one of the nouveau firmware fixes
("drm/gf100-/gr: report class data to host on fwmthd failure")
regenerates a bunch of the firmware files after changing the assembly
by a few lines, without that, its more of a
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm: fix uninitialized acquire_ctx fields (v2)
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
...
Linus Torvalds [Fri, 20 Jun 2014 03:56:43 +0000 (17:56 -1000)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A smaller collection of fixes for the block core that would be nice to
have in -rc2. This pull request contains:
- Fixes for races in the wait/wakeup logic used in blk-mq from
Alexander. No issues have been observed, but it is definitely a
bit flakey currently. Alternatively, we may drop the cyclic
wakeups going forward, but that needs more testing.
- Some cleanups from Christoph.
- Fix for an oops in null_blk if queue_mode=1 and softirq completions
are used. From me.
- A fix for a regression caused by the chunk size setting. It
inadvertently used max_hw_sectors instead of max_sectors, which is
incorrect, and causes hangs on btrfs multi-disk setups (where hw
sectors apparently isn't set). From me.
- Removal of WQ_POWER_EFFICIENT in the kblockd creation. This was a
recent addition as well, but it actually breaks blk-mq which relies
on strict scheduling. If the workqueue power_efficient mode is
turned on, this breaks blk-mq. From Matias.
- null_blk module parameter description fix from Mike"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: bitmap tag: fix races in bt_get() function
blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
blk-mq: bitmap tag: fix races on shared ::wake_index fields
block: blk_max_size_offset() should check ->max_sectors
null_blk: fix softirq completions for queue_mode == 1
blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
blk-mq: properly drain stopped queues
block: remove WQ_POWER_EFFICIENT from kblockd
null_blk: fix name and description of 'queue_mode' module parameter
block: remove elv_abort_queue and blk_abort_flushes
Linus Torvalds [Fri, 20 Jun 2014 03:53:20 +0000 (17:53 -1000)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point.
Unfortunately, one of the two cleanups caused an unintended change in
the original version, so we had to revert one part of it and do some
more testing to ensure the rest is really fine. There was also a
last-minute rebase of the patches to remove another bad commit"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: use menuconfig for sub-arch menus
ARM: multi_v7_defconfig: re-enable SDHCI drivers
ARM: EXYNOS: Fix compilation warning
ARM: exynos: move sysram info to exynos.c
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
ARM: exynos: cleanup kconfig option display
misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
ARM: Remove ARCH_HAS_CPUFREQ config option
ARM: integrator: fix section mismatch problem
ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
ARM: samsung: make SAMSUNG_DMADEV optional
remoteproc: da8xx: don't select CMA on no-MMU
bus/arm-cci: add dependency on OF && CPU_V7
ARM: keystone requires ARM_PATCH_PHYS_VIRT
ARM: omap2: fix am43xx dependency on l2x0 cache
Stephen Boyd [Tue, 3 Jun 2014 18:30:03 +0000 (11:30 -0700)]
unicore32: Remove ARCH_HAS_CPUFREQ config option
This config exists entirely to hide the cpufreq menu from the
kernel configuration unless a platform has selected it. Nothing
is actually built if this config is 'Y' and it just leads to more
patches that add a select under a platform Kconfig so that some
other CPUfreq option can be chosen. Let's remove the option so
that we can always enable CPUfreq drivers on unicore32 platforms.
Guan Xuetao [Mon, 26 May 2014 23:53:10 +0000 (07:53 +0800)]
UniCore32: Change git tree location information in MAINTAINERS
UniCore32 git repo has moved to github.
Branch 'unicore32' is used for prepared patches, and automatically merged to linux-next.
Branch 'unicore32-working' is used for development.
Chen Gang [Tue, 27 May 2014 00:08:06 +0000 (08:08 +0800)]
arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
flush_icache_range() is '__cpuc_coherent_kern_range' under unicore32,
and lkdtm.ko needs it. At present, '__cpuc_coherent_kern_range' is
still used by unicore32, so export it to avoid compiling failure.
The related error (with allmodconfig under unicore32):
Chen Gang [Wed, 21 May 2014 23:08:23 +0000 (07:08 +0800)]
arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
Add generic 'screen_info' just like another architectures have done
(e.g. tile, sh, score, ia64, hexagon, and cris).
The related error (with allmodconfig under unicore32):
LD init/built-in.o
drivers/built-in.o: In function `vgacon_save_screen':
powercap_sys.c:(.text+0x21788): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_resize':
powercap_sys.c:(.text+0x21b54): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_switch':
powercap_sys.c:(.text+0x21cb4): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_init':
powercap_sys.c:(.text+0x2296c): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_startup':
powercap_sys.c:(.text+0x22e80): undefined reference to `screen_info'
Chen Gang [Fri, 9 May 2014 01:19:39 +0000 (09:19 +0800)]
drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
The direct cause is IRQ_SPI is already defined as a macro in unicore32
architecture (also, blackfin and mips architectures define it). The
related error (unicore32 with allmodconfig)
CC [M] drivers/scsi/mvsas/mv_94xx.o
In file included from drivers/scsi/mvsas/mv_94xx.c:27:
drivers/scsi/mvsas/mv_94xx.h:176: error: expected identifier before numeric constant
And IRQ_SAS_A and IRQ_SAS_B are used as 'u32' (although "enum
pci_interrupt_cause" is not used directly, now).
All together, need add 'MVS_' for "enum pci_interrupt_cause".
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Chen Gang [Wed, 21 May 2014 00:57:53 +0000 (08:57 +0800)]
arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
'csum_partial' and 'csum_partial_copy_from_user' have already been
exported in "lib/", so need not export them again, or it will cause
compiling error.
The related error (with allmodconfig under unicore32):
LD vmlinux.o
lib/built-in.o:(___ksymtab+csum_partial+0x0): multiple definition of `__ksymtab_csum_partial'
arch/unicore32/kernel/built-in.o:(___ksymtab+csum_partial+0x0): first defined here
lib/built-in.o:(___ksymtab+csum_partial_copy_from_user+0x0): multiple definition of `__ksymtab_csum_partial_copy_from_user'
arch/unicore32/kernel/built-in.o:(___ksymtab+csum_partial_copy_from_user+0x0): first defined here
make: *** [vmlinux] Error 1
Chen Gang [Sat, 3 May 2014 05:09:02 +0000 (13:09 +0800)]
drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (for unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setalarm':
drivers/rtc/rtc-puv3.c:143: error: 'struct device' has no member named 'dev'
Chen Gang [Sat, 3 May 2014 05:07:57 +0000 (13:07 +0800)]
drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setpie':
drivers/rtc/rtc-puv3.c:74: error: implicit declaration of function 'dev_debug'
Need generic definition for readl_relaxed(), like other architectures
have done. Or can not pass compiling with allmodconfig, the related
error:
CC [M] drivers/message/fusion/mptbase.o
drivers/message/fusion/mptbase.c: In function 'mpt_send_handshake_request':
drivers/message/fusion/mptbase.c:1224: error: implicit declaration of function 'readl_relaxed'
Chen Gang [Mon, 24 Mar 2014 12:54:11 +0000 (20:54 +0800)]
arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
Add generic definition just like another architectures have done, or
can not pass compiling with allmodconfig, the related error:
CC kernel/profile.o
kernel/profile.c: In function 'profile_tick':
kernel/profile.c:419: error: implicit declaration of function 'profile_pc'
make[1]: *** [kernel/profile.o] Error 1
make: *** [kernel] Error 2
Chen Gang [Mon, 24 Mar 2014 12:17:44 +0000 (20:17 +0800)]
arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
Need include "asm/pgtable.h" to include "asm-generic/pgtable-nopmd.h",
so can let 'pmd_t' defined. The related error with allmodconfig:
CC arch/unicore32/mm/alignment.o
In file included from arch/unicore32/mm/alignment.c:24:
arch/unicore32/include/asm/tlbflush.h:135: error: expected .). before .*. token
arch/unicore32/include/asm/tlbflush.h:154: error: expected .). before .*. token
In file included from arch/unicore32/mm/alignment.c:27:
arch/unicore32/mm/mm.h:15: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:20: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:25: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
make[1]: *** [arch/unicore32/mm/alignment.o] Error 1
make: *** [arch/unicore32/mm] Error 2
Chen Gang [Fri, 14 Mar 2014 01:19:39 +0000 (09:19 +0800)]
arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
Add readl() and writel() for 'PM_' macros, just like another areas have
done within unicored32, or will cause compiling issue.
The related error (allmodconfig for unicored32):
CC arch/unicore32/kernel/clock.o
arch/unicore32/kernel/clock.c: In function 'clk_set_rate':
arch/unicore32/kernel/clock.c:182: warning: initialization makes integer from pointer without a cast
arch/unicore32/kernel/clock.c:204: error: lvalue required as left operand of assignment
arch/unicore32/kernel/clock.c:206: error: lvalue required as left operand of assignment
arch/unicore32/kernel/clock.c:207: error: invalid operands to binary & (have 'void *' and 'long unsigned int')
make[1]: *** [arch/unicore32/kernel/clock.o] Error 1
make: *** [arch/unicore32/kernel] Error 2
Chen Gang [Fri, 14 Mar 2014 00:49:27 +0000 (08:49 +0800)]
arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
__vmalloc_area() has already been removed from upstream kernel, need
use __vmalloc_node_range() instead of.
The related commit: "d0a2126 mm: unify module_alloc code for vmalloc".
The related error (allmodconfig for unicore32):
CC arch/unicore32/kernel/module.o
arch/unicore32/kernel/module.c: In function 'module_alloc' :
arch/unicore32/kernel/module.c:34: error: implicit declaration of function '__vmalloc_area'
arch/unicore32/kernel/module.c:34: warning: return makes pointer from integer without a cast
make[1]: *** [arch/unicore32/kernel/module.o] Error 1
make: *** [arch/unicore32/kernel] Error 2
Others are only within some architectures (not kernel wide).
The related error with allmodconfig for unicode32:
CC arch/unicore32/kernel/ksyms.o
arch/unicore32/kernel/ksyms.c:29: error: ._backtrace. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:29: error: type defaults to .nt. in declaration of ._backtrace.
arch/unicore32/kernel/ksyms.c:38: error: .sum_partial_copy_nocheck. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:38: error: type defaults to .nt. in declaration of .sum_partial_copy_nocheck.
arch/unicore32/kernel/ksyms.c:39: error: ._csum_ipv6_magic. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:39: error: type defaults to .nt. in declaration of ._csum_ipv6_magic.
arch/unicore32/kernel/ksyms.c:43: error: ._raw_readsb. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:43: error: type defaults to .nt. in declaration of ._raw_readsb.
arch/unicore32/kernel/ksyms.c:46: error: ._raw_readsw. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:46: error: type defaults to .nt. in declaration of ._raw_readsw.
arch/unicore32/kernel/ksyms.c:49: error: ._raw_readsl. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:49: error: type defaults to .nt. in declaration of ._raw_readsl.
arch/unicore32/kernel/ksyms.c:52: error: ._raw_writesb. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:52: error: type defaults to .nt. in declaration of ._raw_writesb.
arch/unicore32/kernel/ksyms.c:55: error: ._raw_writesw. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:55: error: type defaults to .nt. in declaration of ._raw_writesw.
arch/unicore32/kernel/ksyms.c:58: error: ._raw_writesl. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:58: error: type defaults to .nt. in declaration of ._raw_writesl.
arch/unicore32/kernel/ksyms.c:79: error: ._get_user_1. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:79: error: type defaults to .nt. in declaration of ._get_user_1.
arch/unicore32/kernel/ksyms.c:80: error: ._get_user_2. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:80: error: type defaults to .nt. in declaration of ._get_user_2.
arch/unicore32/kernel/ksyms.c:81: error: ._get_user_4. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:81: error: type defaults to .nt. in declaration of ._get_user_4.
arch/unicore32/kernel/ksyms.c:83: error: ._put_user_1. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:83: error: type defaults to .nt. in declaration of ._put_user_1.
arch/unicore32/kernel/ksyms.c:84: error: ._put_user_2. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:84: error: type defaults to .nt. in declaration of ._put_user_2.
arch/unicore32/kernel/ksyms.c:85: error: ._put_user_4. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:85: error: type defaults to .nt. in declaration of ._put_user_4.
arch/unicore32/kernel/ksyms.c:86: error: ._put_user_8. undeclared here (not in a function)
arch/unicore32/kernel/ksyms.c:86: error: type defaults to .nt. in declaration of ._put_user_8.
Miao Xie [Thu, 19 Jun 2014 02:42:55 +0000 (10:42 +0800)]
Btrfs: fix wrong error handle when the device is missing or is not writeable
The original bio might be submitted, so we shoud increase bi_remaining to
account for it when we deal with the error that the device is missing or
is not writeable, or we would skip the endio handle.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Miao Xie [Thu, 19 Jun 2014 02:42:54 +0000 (10:42 +0800)]
Btrfs: fix deadlock when mounting a degraded fs
The deadlock happened when we mount degraded filesystem, the reproduced
steps are following:
# mkfs.btrfs -f -m raid1 -d raid1 <dev0> <dev1>
# echo 1 > /sys/block/`basename <dev0>`/device/delete
# mount -o degraded <dev1> <mnt>
The reason was that the counter -- bi_remaining was wrong. If the missing
or unwriteable device was the last device in the mapping array, we would
not submit the original bio, so we shouldn't increase bi_remaining of it
in btrfs_end_bio(), or we would skip the final endio handle.
Fix this problem by adding a flag into btrfs bio structure. If we submit
the original bio, we will set the flag, and we increase bi_remaining counter,
or we don't.
Though there is another way to fix it -- decrease bi_remaining counter of the
original bio when we make sure the original bio is not submitted, this method
need add more check and is easy to make mistake.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com>
Qu Wenruo [Thu, 19 Jun 2014 02:42:51 +0000 (10:42 +0800)]
btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
When run scrub with balance, sometimes -ENOENT will be returned, since
in scrub_enumerate_chunks() will search dev_extent in *COMMIT_ROOT*, but
btrfs_lookup_block_group() will search block group in *MEMORY*, so if a
chunk is removed but not committed, -ENOENT will be returned.
However, there is no need to stop scrubbing since other chunks may be
scrubbed without problem.
So this patch changes the behavior to skip removed chunks and continue
to scrub the rest.
Miao Xie [Thu, 19 Jun 2014 02:42:50 +0000 (10:42 +0800)]
Btrfs: fix broken free space cache after the system crashed
When we mounted the filesystem after the crash, we got the following
message:
BTRFS error (device xxx): block group xxxx has wrong amount of free space
BTRFS error (device xxx): failed to load free space cache for block group xxx
It is because we didn't update the metadata of the allocated space (in extent
tree) until the file data was written into the disk. During this time, there was
no information about the allocated spaces in either the extent tree nor the
free space cache. when we wrote out the free space cache at this time (commit
transaction), those spaces were lost. In fact, only the free space that is
used to store the file data had this problem, the others didn't because
the metadata of them is updated in the same transaction context.
There are many methods which can fix the above problem
- track the allocated space, and write it out when we write out the free
space cache
- account the size of the allocated space that is used to store the file
data, if the size is not zero, don't write out the free space cache.
The first one is complex and may make the performance drop down.
This patch chose the second method, we use a per-block-group variant to
account the size of that allocated space. Besides that, we also introduce
a per-block-group read-write semaphore to avoid the race between
the allocation and the free space cache write out.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Miao Xie [Thu, 19 Jun 2014 02:42:49 +0000 (10:42 +0800)]
Btrfs: make free space cache write out functions more readable
This patch makes the free space cache write out functions more readable,
and beisdes that, it also reduces the stack space that the function --
__btrfs_write_out_cache uses from 194bytes to 144bytes.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Filipe Manana [Mon, 16 Jun 2014 12:14:25 +0000 (13:14 +0100)]
Btrfs: remove unused wait queue in struct extent_buffer
The lock_wq wait queue is not used anywhere, therefore just remove it.
On a x86_64 system, this reduced sizeof(struct extent_buffer) from 320
bytes down to 296 bytes, which means a 4Kb page can now be used for
13 extent buffers instead of 12.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com>
Chris Mason [Thu, 19 Jun 2014 21:16:52 +0000 (14:16 -0700)]
Btrfs: fix deadlocks with trylock on tree nodes
The Btrfs tree trylock function is poorly named. It always takes
the spinlock and backs off if the blocking lock is held. This
can lead to surprising lockups because people expect it to really be a
trylock.
This commit makes it a pure trylock, both for the spinlock and the
blocking lock. It also reworks the nested lock handling slightly to
avoid taking the read lock while a spinning write lock might be held.
George Cherian [Mon, 26 May 2014 09:20:08 +0000 (14:50 +0530)]
usb: musb: core: Handle Babble condition only in HOST mode
BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.
Handle babble condition iff MUSB is in HOST mode.
Fixes: ca88fc2ef0d7 (usb: musb: add a work_struct to recover from babble errors) Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Rob Herring [Thu, 12 Jun 2014 17:52:44 +0000 (12:52 -0500)]
tty/serial: fix 8250 early console option passing to regular console
In the conversion to generic early console, the passing of options from
the early 8250 console to the regular ttyS console was broken. This
resulted in the baud rate changing when switching consoles during boot.
This feature allows specifying a single console option on the kernel
command line rather than both an early console and regular serial tty
console. It would be nice to generalize this feature. However, it only
works if the correct baud rate can be probed early which is not the
case on many platforms which have non-standard UART clock rates. So for
now, this is left as an 8250 specific feature.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 16 Jun 2014 12:10:42 +0000 (08:10 -0400)]
tty: Correct INPCK handling
If INPCK is not set, input parity detection should be disabled. This means
parity errors should not be received from the tty driver, and the data
received should be treated normally.
SUS v3, 11.2.2, General Terminal Interface - Input Modes, states:
"If INPCK is set, input parity checking shall be enabled. If INPCK is
not set, input parity checking shall be disabled, allowing output parity
generation without input parity errors. Note that whether input parity
checking is enabled or disabled is independent of whether parity detection
is enabled or disabled (see Control Modes). If parity detection is enabled
but input parity checking is disabled, the hardware to which the terminal
is connected shall recognize the parity bit, but the terminal special file
shall not check whether or not this bit is correctly set."
Ignore parity errors reported by the tty driver when INPCK is not set, and
handle the received data normally.
Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 16 Jun 2014 12:10:41 +0000 (08:10 -0400)]
serial: Fix IGNBRK handling
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Linus Torvalds [Thu, 19 Jun 2014 17:53:27 +0000 (07:53 -1000)]
Merge tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from David Vrabel:
"Xen regression and PVH fixes for 3.16-rc1
- fix dom0 PVH memory setup on latest unstable Xen releases
- fix 64-bit x86 PV guest boot failure on Xen 3.1 and earlier
- fix resume regression on non-PV (auto-translated physmap) guests"
* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: fix suspend for non-PV guests
x86/xen: no need to explicitly register an NMI callback
Revert "xen/pvh: Update E820 to work with PVH (v2)"
x86/xen: fix memory setup for PVH dom0
Linus Torvalds [Thu, 19 Jun 2014 17:51:45 +0000 (07:51 -1000)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are primarily bug fixes with a performance improvement patch for
the GHASH crypto algorithm (which went in during this merging window)
and dts/defconfig/Kconfig updates.
- ftrace_return_addr() macro fix for arm (introduced earlier via the
arm64 tree)
- stack alignment exception entry code fix
- GHASH crypto algorithm fix and performance improvement
- CMA buffer limited to 32-bit (until a better way to describe the
system topology in DT)
- UAPI sigcontext.h build fix
- __kernel_old_{gid,uid}_t definitions fix (affecting 32-bit LTP)
- ptrace fixes (kernel fault and 32-bit arm core dump)
- pte_mknotpresent() fix
- dts updates (APM SoC)
- defconfig and Kconfig update"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: remove broken &= operator from pmd_mknotpresent
arm64: fix build error in sigcontext.h
arm64: dts: Add more serial port nodes in APM X-Gene device tree
arm64/dma: Removing ARCH_HAS_DMA_GET_REQUIRED_MASK macro
arm64: ptrace: fix empty registers set in prstatus of aarch32 process core
arm64: uid16: fix __kernel_old_{gid,uid}_t definitions
arm64: ptrace: change fs when passing kernel pointer to regset code
arm64: Limit the CMA buffer to 32-bit if ZONE_DMA
arm/ftrace: fix ftrace_return_addr() to ftrace_return_address()
arm64/crypto: improve performance of GHASH algorithm
arm64/crypto: fix data corruption bug in GHASH algorithm
arm64: defconfig update for LTP
arm64: ftrace: Fix comment typo 'CONFIG_FUNCTION_GRAPH_FP_TEST'
arm64: add ARCH_HAS_OPP to allow enabling OPP library
arm64: restore alphabetic order in Kconfig
arm64: Bug fix in stack alignment exception
This reverts commit 1826e9b1 (usb: gadget: gadgetfs: use
after free in dev_release()) and places the call to
put_dev() after setting the state.
If this is not the final call to dev_release() and the
state is not reset to STATE_DEV_DISABLED and hence all
further open() calls to the gadgetfs ep0 device will
fail with EBUSY.
Signed-off-by: Marcus Nutzinger <marcus.nutzinger@theobroma-systems.com> Reviewed-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: OS descriptors: provide interface directory names
Function's interface directories need to be created when the function
directory is created, but interface numbers are not known until
the gadget is ready and bound to udc, so we cannot use numbers
as part of interface directory names.
Let the client decide what names to use.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
A number of variables serve a generic purpose of handling
"compatible id" and "subcompatible id", but the names suggest they
are for rndis only. Rename to reflect variables' purpose.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_fs: fix NULL pointer dereference when there are no strings
If the descriptors do not need any strings and user space sends empty
set of strings, the ffs->stringtabs field remains NULL. Thus
*ffs->stringtabs in functionfs_bind leads to a NULL pointer
dereferenece.
The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”].
While at it, remove double initialisation of lang local variable in
that function.
ffs->strings_count does not need to be checked in any way since in
the above scenario it will remain zero and usb_string_ids_n() is
a no-operation when colled with 0 argument.
Cc: <stable@vger.kernel.org> # v2.6.36+ Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Walleij [Tue, 10 Jun 2014 08:54:16 +0000 (10:54 +0200)]
usb: musb: ux500: don't propagate the OF node
There is a regression in the upcoming v3.16-rc1, that is caused
by a problem that has been around for a while but now finally
hangs the system. The bootcrawl looks like this:
pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already
requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
pinctrl-nomadik soc:pinctrl: could not request pin 256
(GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
musb-hdrc musb-hdrc.0.auto: Error applying setting, reverse
things back
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed
with status -517
platform musb-hdrc.0.auto: Driver musb-hdrc requests
probe deferral
(...)
The ux500 MUSB driver propagates the OF node to the dynamically
created musb-hdrc device, which is incorrect as it makes the OF
core believe there are two devices spun from the very same
DT node, which confuses other parts of the device core, notably
the pin control subsystem, which will try to apply all the pin
control settings also to the HDRC device as it gets
instantiated. (The OMAP2430 for example, does not set the
of_node member.)
Cc: <stable@vger.kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: renesas: gadget: fixup: complete STATUS stage after receiving
Current usbhs gadget driver didn't complete STATUS stage after receiving.
It wasn't problem for us before, because some USB class doesn't use
DATA OUT stage in control transfer.
But, it is required on some device.
Jeff Westfahl [Thu, 29 May 2014 06:49:41 +0000 (09:49 +0300)]
usb: gadget: u_ether: synchronize with transmit when stopping queue
When disconnecting, it's possible that another thread has already made it
into eth_start_xmit before we call netif_stop_queue. This can lead to a
crash as eth_start_xmit tries to use resources that gether_disconnect is
freeing. Use netif_tx_lock/unlock around netif_stop_queue to ensure no
threads are executing during the remainder of gether_disconnect.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com> Tested-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
George Cherian [Thu, 22 May 2014 04:01:38 +0000 (09:31 +0530)]
usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete
The dwc3 wrapper driver should not be fiddling with the core interrupts.
Disabling the core interrupts in prepare stops xhci from proper operation.
So remove disable/enable of core interrupts from prepare/complete.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Wed, 21 May 2014 12:26:55 +0000 (15:26 +0300)]
usb: gadget: f_rndis: fix an error code on allocation failure
This should be return -ENOMEM. The current code returns successs.
Fixes: de7a8d2d534f ('usb: gadget: f_rndis: OS descriptors support') Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
tools: ffs-test: convert to new descriptor format fixing compilation error
Commit [ac8dde11: “usb: gadget: f_fs: Add flags to descriptors block”]
which introduced a new descriptor format for FunctionFS removed the
usb_functionfs_descs_head structure, which is still used by ffs-test.
tool.
Convert ffs-test by converting it to use the new header format. For
testing kernels prior to 3.14 (when the new format was introduced) and
parsing of the legacy headers in the new kernels, provide a compilation
flag to make the tool use the old format.
Finally, include information as to when the legacy FunctionFS headers
format has been deprecated (which is also when the new one has been
introduced).
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Zhuang Jin Can [Thu, 15 May 2014 21:57:57 +0000 (05:57 +0800)]
usb: dwc3: gadget: check link trb after free_slot is increased
In ISOC transfers, when free_slot points to the last TRB (i.e. Link
TRB), and all queued requests meet Missed Interval Isoc error, busy_slot
points to trb0.
busy_slot->trb0
trb1
...
free_slot->trb31(Link TRB)
After end transfer and receiving the XferNotReady event, trb_left is
caculated as 1 which is wrong, and no TRB will be primed to the
endpoint.
The root cause is free_slot is not increased the same way as busy_slot.
When busy_slot is increased by one, it checks if points to a link TRB
after increasement, but free_slot checks it before increasement.
free_slot should behave the same as busy_slot to make the trb_left
caculation correct.
Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Jiebing Li <jiebing.li@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Dave Airlie [Thu, 19 Jun 2014 00:54:35 +0000 (10:54 +1000)]
Merge tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel into drm-next
First round of fixes for 3.16-rc, mostly cc: stable, and the vt/vgacon
fixes from Daniel [1] to avoid hangs and unclaimed register errors on
module load/reload.
* tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bdw: remove erroneous chv specific workarounds from bdw code
drm/i915: fix possible refcount leak when resetting forcewake
drm/i915: Reorder semaphore deadlock check
drm/i95: Initialize active ring->pid to -1
drm/i915: set backlight duty cycle after backlight enable for gen4
drm/i915: Avoid div-by-zero when pixel_multiplier is zero
drm/i915: Disable FBC by default also on Haswell and later
drm/i915: Kick out vga console
drm/i915: Fixup global gtt cleanup
vt: Don't ignore unbind errors in vt_unbind
vt: Fix up unregistration of vt drivers
vt: Fix replacement console check when unbinding
Rob Clark [Sat, 7 Jun 2014 14:55:39 +0000 (10:55 -0400)]
drm: fix uninitialized acquire_ctx fields (v2)
The acquire ctx will typically be declared on the stack, which means we
could have garbage values for any uninitialized field. In this case, it
was triggering WARN_ON()s because 'contended' had garbage value.
Go ahead and use memset() to be more future-proof.
v2: now with extra brown paper bag
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 19 Jun 2014 00:25:49 +0000 (10:25 +1000)]
Merge branch 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux into drm-next
mode validation, deep color and pageflipping fixes.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
With commit aed3f9d498b ("staging: comedi: addi_apci_1564:
absorb apci1564_reset()"), the apci 1564 driver has gained
a dependency on the addi watchdog module, which is not reflected
correctly in Kconfig, and that can lead to link errors
when the watchdog is disabled.
This adds an explicit 'select', like it is done in the other
addi apci drivers that need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / mirror_ubuntu-bionic-kernel.git / log