The new format of an SMCD V2 CLC proposal is introduced, and
building and checking of SMCD V2 CLC proposals is adapted
accordingly.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows to propose up to 8 additional ISM devices
offered to the peer as candidates for SMCD communication.
This patch covers determination of the ISM devices to be proposed.
ISM devices without PNETID are preferred, since ISM devices with
PNETID are a V1 leftover and will disappear over the time.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: introduce list of pnetids for Ethernet devices
SMCD version 2 allows usage of ISM devices with hardware PNETID
only, if an Ethernet net_device exists with the same hardware PNETID.
This requires to maintain a list of pnetids belonging to
Ethernet net_devices, which is covered by this patch.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines a System Enterprise ID (short SEID).
This patch contains the SEID creation and adds the callback to
retrieve the created SEID.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows proposing of up to 8 ISM devices in addition
to the native ISM device of SMCD Version 1.
This patch prepares the struct smc_init_info to deal with these
additional 8 ISM devices.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When sending CLC confirm and CLC accept, separate the trailing
part of the message from the initial part (to be prepared for
future first contact extension).
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides better separation of device determinations
in function smc_listen_work(). No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines 2 more bits in the CLC header to specify
version 2 types. This patch prepares better naming of the CLC
header fields. No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Sep 2020 21:54:13 +0000 (14:54 -0700)]
Merge branch '1GbE' of https://github.com/anguy11/next-queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2020-09-28
This series contains updates to igb, igc, and e1000e drivers.
Sven Auhagen adds XDP support for igb.
Gal Hammer allows for 82576 to display part number string correctly for
igb.
Sasha adds device IDs for i221 and i226 parts. Exposes LPI counters and
removes unused fields in structures for igc. He also adds Meteor Lake
support for e1000e.
For igc, Andre renames IGC_TSYNCTXCTL_VALID to IGC_TSYNCTXCTL_TXTT_0 to
match the datasheet and adds a warning if it's not set when expected.
Removes the PTP Tx timestamp check in igc_ptp_tx_work() as it's already
checked in the watchdog_task. Cleans up some code by removing invalid error
bits, renaming a bit to match datasheet naming, and removing a, now
unneeded, macro.
Vinicius makes changes for igc PTP: removes calling SYSTIMR to latch timer
value, stores PTP time before a reset, and rejects schedules with times in
the future.
v2: Remove 'inline' from igb_xdp_tx_queue_mapping() and igb_rx_offset()
for patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Neftin [Thu, 13 Aug 2020 08:34:06 +0000 (11:34 +0300)]
e1000e: Add support for Meteor Lake
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Meteor Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc: Reject schedules with a base_time in the future
When we set the BASET registers of i225 with a base_time in the
future, i225 will "hold" all packets until that base_time is reached,
causing a lot of TX Hangs.
As this behaviour seems contrary to the expectations of the IEEE
802.1Q standard (section 8.6.9, especially 8.6.9.4.5), let's start by
rejecting these types of schedules. If this is too limiting, we can
for example, setup a timer to configure the BASET registers closer to
the start time, only blocking the packets for a "short" while.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The next patch will need a way to retrieve the current timestamp from
the NIC's PTP clock.
The 'i225' suffix is removed, if anything model specific is needed,
those specifics should be hidden by this function.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Many TSN features depend on the internal PTP clock, so the internal
PTP jumping when the adapter is reset can cause problems, usually in
the form of "TX Hangs" warnings in the driver.
The solution is to save the PTP time before a reset and restore it
after the reset is done. The value of the PTP time is saved before a
reset and we use the difference from CLOCK_MONOTONIC from reset time
to now, to correct what's going to be the new PTP time.
This is heavily inspired by commit bf4bf09bdd91 ("i40e: save PTP time
before a device reset").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In i225, it's no longer necessary to use the SYSTIMR register to
latch the timer value, the timestamp is latched when SYSTIML is read.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sasha Neftin [Thu, 13 Aug 2020 15:18:15 +0000 (18:18 +0300)]
igc: Expose LPI counters
Completion to commit 900d1e8b346b ("igc: Add LPI counters")
LPI counters exposed by statistics update method.
A EEE TX LPI counter reflect the transmitter entries EEE (IEEE 802.3az)
into the LPI state. A EEE RX LPI counter reflect the receiver link
partner entries into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Andre Guedes [Mon, 10 Aug 2020 21:08:30 +0000 (14:08 -0700)]
igc: Clean RX descriptor error flags
i225 advanced receive descriptor doesn't have the following extend error
bits: CE, SE, SEQ, CXE. In addition to that, the bit TCPE is called L4E
in the datasheet.
Clean up the code accordingly, and get rid of the macro
IGC_RXDEXT_ERR_FRAME_ERR_MASK since it doesn't make much sense anymore.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Andre Guedes [Tue, 28 Jul 2020 23:37:53 +0000 (16:37 -0700)]
igc: Remove timeout check from ptp_tx work
The Tx timestamp timeout is already checked by the watchdog_task
which runs periodically. In addition to that, from the ptp_tx work
perspective, if __IGC_PTP_TX_IN_PROGRESS flag is set we always want
handle the timestamp stored in hardware and update the skb. So remove
the timeout check in igc_ptp_tx_work() function.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Andre Guedes [Tue, 28 Jul 2020 23:37:52 +0000 (16:37 -0700)]
igc: Don't reschedule ptp_tx work
The ptp_tx work is scheduled only if TSICR.TXTS bit is set, therefore
TSYNCTXCTL.TXTT_0 bit is expected to be set when we check it igc_ptp_tx_
work(). If it isn't, something is really off and rescheduling the ptp_tx
work to check it later doesn't help much. This patch changes the code to
WARN_ON_ONCE() if this situation ever happens.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Andre Guedes [Tue, 28 Jul 2020 23:37:51 +0000 (16:37 -0700)]
igc: Rename IGC_TSYNCTXCTL_VALID macro
Rename the IGC_TSYNCTXCTL_VALID macro to IGC_TSYNCTXCTL_TXTT_0 so it
matches the datasheet.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Gal Hammer [Sun, 30 Aug 2020 05:45:29 +0000 (08:45 +0300)]
igb: read PBA number from flash
Fixed flash presence check for 82576 controllers so the part
number string is read and displayed correctly.
Signed-off-by: Gal Hammer <ghammer@redhat.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sven Auhagen [Wed, 2 Sep 2020 20:32:22 +0000 (13:32 -0700)]
igb: add XDP support
Add XDP support to the IGB driver.
The implementation follows the IXGBE XDP implementation
closely and I used the following patches as basis:
1. commit 924708081629 ("ixgbe: add XDP support for pass and drop actions")
2. commit 33fdc82f0883 ("ixgbe: add support for XDP_TX action")
3. commit ed93a3987128 ("ixgbe: tweak page counting for XDP_REDIRECT")
Due to the hardware constraints of the devices using the
IGB driver we must share the TX queues with XDP which
means locking the TX queue for XDP.
I ran tests on an older device to get better numbers.
Test machine:
====================
udp_tunnel: convert Intel drivers with shared tables
This set converts Intel drivers which have the ability to spawn
multiple netdevs, but have only one UDP tunnel port table.
Appropriate support is added to the core infra in patch 1,
followed by netdevsim support and a selftest.
The table sharing works by core attaching the same table
structure to all devices sharing the table. This means the
reference count has to accommodate potentially large values.
Once core is ready i40e and ice are converted. These are
complex drivers, but we got a tested-by from Aaron, so we
should be good :)
Compared to v1 I've made sure the selftest is executable.
Other than that patches 8 and 9 are actually from the Mellanox
conversion series were kept out to avoid Mellanox vs Intel
conflicts.
Last patch is new, some docs to let users knows ethtool
can now display UDP tunnel info.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 26 Sep 2020 00:56:44 +0000 (17:56 -0700)]
i40e: convert to new udp_tunnel infrastructure
Make use of the "shared port table" to convert i40e to the new
infra.
i40e did not have any reference tracking, locking is also dodgy
because rtnl gets released while talking to FW, so port may get
removed from the table while it's getting added etc.
On the good side i40e does not seem to be using the ports for
TX so we can remove the table from the driver state completely.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 26 Sep 2020 00:56:41 +0000 (17:56 -0700)]
netdevsim: add warnings on unexpected UDP tunnel port errors
We should never see a removal of a port which is not in the table
or adding a port to an occupied entry in the table. To make sure
such errors don't escape the checks in the test script add a
warning/kernel spat.
Error injection will not trigger those, nor should it ever put
us in a bad state.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 26 Sep 2020 00:56:40 +0000 (17:56 -0700)]
udp_tunnel: add the ability to share port tables
Unfortunately recent Intel NIC designs share the UDP port table
across netdevs. So far the UDP tunnel port state was maintained
per netdev, we need to extend that to cater to Intel NICs.
Expect NICs to allocate the info structure dynamically and link
to the state from there. All the shared NICs will record port
offload information in the one instance of the table so we need
to make sure that the use count can accommodate larger numbers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Mon, 28 Sep 2020 14:51:35 +0000 (09:51 -0500)]
net: phy: dp83869: Add speed optimization feature
Set the speed optimization bit on the DP83869 PHY.
Speed optimization, also known as link downshift, enables fallback to 100M
operation after multiple consecutive failed attempts at Gigabit link
establishment. Such a case could occur if cabling with only four wires
(two twisted pairs) were connected instead of the standard cabling with
eight wires (four twisted pairs).
The number of failed link attempts before falling back to 100M operation is
configurable. By default, four failed link attempts are required before
falling back to 100M.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: vlan: Fixed signedness in vlan_group_prealloc_vid()
After commit d0186842ec5f ("net: vlan: Avoid using BUG() in
vlan_proto_idx()"), vlan_proto_idx() was changed to return a signed
integer, however one of its called: vlan_group_prealloc_vid() was still
using an unsigned integer for its return value, fix that.
Fixes: d0186842ec5f ("net: vlan: Avoid using BUG() in vlan_proto_idx()") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 27 Sep 2020 20:35:46 +0000 (13:35 -0700)]
Merge branch 'bnxt_en-Update-for-net-next'
Michael Chan says:
====================
bnxt_en: Update for net-next.
This patch series adds 2 main features to the bnxt_en driver: 200G
link speed support and FEC support with some refactoring of the
link speed logic. The firmware interface is updated to have proper
support for these 2 features. The ethtool preset max channel value
is also adjusted properly to account for XDP and TCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 27 Sep 2020 17:42:20 +0000 (13:42 -0400)]
bnxt_en: Improve preset max value for ethtool -l.
The current logic that calculates the preset maximum value for combined
channel does not take into account the rings used for XDP and mqprio
TCs. Each of these features will reduce the number of TX rings. Add
the logic to divide the TX rings accordingly based on whether the
device is currently in XDP mode and whether TCs are in use.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 27 Sep 2020 17:42:18 +0000 (13:42 -0400)]
bnxt_en: Report Active FEC encoding during link up.
The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 27 Sep 2020 17:42:17 +0000 (13:42 -0400)]
bnxt_en: Report FEC settings to ethtool.
Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 27 Sep 2020 17:42:15 +0000 (13:42 -0400)]
bnxt_en: Handle ethernet link being disabled by firmware.
On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port. Firmware
will send notification to the driver for the disabled port when this
happens. Define a new field in the link_info structure to keep track
of this state. The new phy_state field replaces the unused loop_back
field.
Log a message when the phy_state changes state. In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: ethtool: support PAM4 link speeds up to 200G
Add ethtool PAM4 link modes for:
50000baseCR_Full
100000baseCR2_Full
200000baseCR4_Full
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: add basic infrastructure to support PAM4 link speeds
The firmware interface has added support for new link speeds using
PAM4 modulation. Expand the bnxt_link_info structure to closely
mirror the new firmware structures. Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.
Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.
Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 27 Sep 2020 17:42:10 +0000 (13:42 -0400)]
bnxt_en: Update firmware interface spec to 1.10.1.65.
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu [Sun, 27 Sep 2020 08:01:50 +0000 (16:01 +0800)]
ptp: add stub function for ptp_get_msgtype()
Added the missing stub function for ptp_get_msgtype().
Fixes: 036c508ba95e ("ptp: Add generic ptp message type function") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 26 Sep 2020 21:26:03 +0000 (23:26 +0200)]
net: marvell: mvpp2: Fix W=1 warning with !CONFIG_ACPI
rivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:7084:36: warning: ‘mvpp2_acpi_match’ defined but not used [-Wunused-const-variable=]
7084 | static const struct acpi_device_id mvpp2_acpi_match[] = {
| ^~~~~~~~~~~~~~~~
Wrap the definition inside #ifdef/#endif.
Compile tested only.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
An overheated transceiver can be the root cause of various network
problems such as link flapping. Counting the number of times a
transceiver's temperature was higher than its configured threshold can
therefore help in debugging such issues.
This patch set exposes a transceiver overheat counter via ethtool. This
is achieved by configuring the Spectrum ASIC to generate events whenever
a transceiver is overheated. The temperature thresholds are queried from
the transceiver (if available) and set to the default otherwise.
Example:
...
transceiver_overheat: 2
Patch set overview:
Patches #1-#3 add required device registers
Patches #4-#5 add required infrastructure in mlxsw to configure and
count overheat events
Patches #6-#9 gradually add support for the transceiver overheat counter
Patch #10 exposes the transceiver overheat counter via ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures for port statistics which read from core and not directly
from registers.
When netdev's ethtool statistics are queried, query the corresponding
module's overheat counter from core and expose it as
"transceiver_overheat".
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 27 Sep 2020 07:50:14 +0000 (10:50 +0300)]
mlxsw: Update module's settings when module is plugged in
Module temperature warning events are enabled for modules that have a
temperature sensor and configured according to the temperature
thresholds queried from the module.
When a module is unplugged we are guaranteed not to get temperature
warning events. However, when a module is plugged in we need to
potentially update its current settings (i.e., event enablement and
thresholds).
Register to port module plug/unplug events and update module's settings
upon plug in events.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The overheat counter is a per-module counter, but it is exposed as part
of the corresponding netdev's statistics. It should therefore be
presented to user space relative to the netdev's lifetime.
Query the counter just before registering the netdev, so that the value
exposed to user space will be relative to this initial value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 27 Sep 2020 07:50:10 +0000 (10:50 +0300)]
mlxsw: core: Add an infrastructure to track transceiver overheat counter
Initialize an array that stores per-module overheat state and a counter
indicating how many times the module was in overheat state.
Export a function to query the counter according to module number.
Will be used later on by the switch driver (i.e., mlxsw_spectrum) to expose
module's overheat counter as part of ethtool statistics.
Initialize mlxsw_env after driver initialization to be able to query
number of modules from MGPIR register.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 27 Sep 2020 07:50:09 +0000 (10:50 +0300)]
mlxsw: core_hwmon: Query MTMP before writing to set only relevant fields
The MTMP register controls various temperature settings on a per-sensor
basis. Subsequent patches are going to alter some of these settings for
sensors found on port modules in response to certain events.
In order to prevent the current callers that write to MTMP from
overriding these settings, have them first query the register and then
change only the relevant register fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 27 Sep 2020 07:50:07 +0000 (10:50 +0300)]
mlxsw: reg: Add Port Module Plug/Unplug Event Register
PMPE register reports any operational status change of a module.
It will be used for enabling temperature warning event when a module is
plugged in.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 27 Sep 2020 07:50:06 +0000 (10:50 +0300)]
mlxsw: reg: Add Management Temperature Warning Event Register
Add MTWE (Management Temperature Warning Event) register, which is used
for over temperature warning.
Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 27 Sep 2020 20:25:22 +0000 (13:25 -0700)]
Merge branch 'hns3-next'
Huazhong Tan says:
====================
net: hns3: updates for -next
To facilitate code maintenance and compatibility, #1 and #2 add
device version to replace pci revision, #3 to #9 adds support for
querying device capabilities and specifications, then the driver
can use these query results to implement corresponding features
(some features will be implemented later).
And #10 is a minor cleanup since too many parameters for
hclge_shaper_para_calc().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: add a check for device specifications queried from firmware
The device specifications querying is unsupported by the old
firmware, in this case, these specifications are 0. However,
some specifications should not be 0 or will cause problem.
So after querying from firmware, some device specifications
are needed to check their value and set to default value if
their values are 0.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: replace the macro of max tm rate with the queried specification
The max tm rate is a fixed value(100Gb/s) now as it is defined by a
macro. In order to support other rates in different kinds of device,
it is better to use specification queried from firmware to replace
this macro.
As function hclge_shaper_para_calc() has too many arguments to add
more, so encapsulate its three arguments ir_b, ir_u, ir_s into a
structure.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: add support to query device specifications
To improve code maintainability and compatibility, new commands
HCLGE_OPC_QUERY_DEV_SPECS for PF and HCLGEVF_OPC_QUERY_DEV_SPECS
for VF are introduced to query device specifications, instead of
statically defining specifications by checking the hardware version
or other methods.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: add debugfs to dump device capabilities
Adds debugfs to dump each device capability whether is supported.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve code maintainability and compatibility, the
capabilities of new features are queried from firmware.
The member flag in struct hnae3_ae_dev indicates not only
capabilities, but some initialized status. As capabilities bits
queried from firmware is too many, it is better to use new member
to indicate them. So adds member capabs in struce hnae3_ae_dev.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the revision of the pci device is used to identify
whether FEC is supported, which is not good for maintainability
and compatibility. So use a capability flag to do that.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve code maintainability and compatibility,
add support to query the device capability by expanding the
existing version query command. The device capability refers
to the features supported by the device.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fibre device of PCI revision 0x20 don't support autoneg, and the ops
get_autoneg() return AUTONEG_DISABLE so function hns3_nway_reset()
will return earlier than judging PCI revision.
Function hclge_handle_rocee_ras_error() don't need to judge PCI
revision again because its caller hclge_handle_hw_ras_error() has
judged once.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: add device version to replace pci revision
To better identify the device version, struct hnae3_handle adds a
member dev_version to replace pci revision. The dev_version consists
of hardware version and PCI revision. The hardware version is queried
from firmware by an existing firmware version query command.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 26 Sep 2020 01:19:13 +0000 (18:19 -0700)]
netdevsim: fix duplicated debugfs directory
The "ethtool" debugfs directory holds per-netdev knobs, so move
it from the device instance directory to the port directory.
This fixes the following warning when creating multiple ports:
debugfs: Directory 'ethtool' with parent 'netdevsim1' already present!
Fixes: ff1f7c17fb20 ("netdevsim: add pause frame stats") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Generic adjustment for flow dissector in DSA
This is the v2 of a series initially submitted in May:
https://www.spinics.net/lists/netdev/msg651866.html
The end goal is to get rid of the unintuitive code for the flow
dissector that currently exists in the taggers. It can all be replaced
by a single, common function.
Some background work needs to be done for that. Especially the ocelot
driver poses some problems, since it has a different tag length between
RX and TX, and I didn't want to make DSA aware of that, since I could
instead make the tag lengths equal.
Changes in v3:
- Added an optimization (08/15) that makes the generic case not need to
call the .flow_dissect function pointer. Basically .flow_dissect now
currently only exists for sja1105.
- Moved the .promisc_on_master property to the tagger structure.
- Added the .tail_tag property to the tagger structure.
- Disabled "suppresscc = all" from my .gitconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:15 +0000 (22:32 +0300)]
net: dsa: tag_rtl4_a: use the generic flow dissector procedure
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Linus Walleij <linus.walleij@linaro.org> Cc: DENG Qingfang <dqfext@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:14 +0000 (22:32 +0300)]
net: dsa: tag_sja1105: use a custom flow dissector procedure
The sja1105 is a bit of a special snowflake, in that not all frames are
transmitted/received in the same way. L2 link-local frames are received
with the source port/switch ID information put in the destination MAC
address. For the rest, a tag_8021q header is used. So only the latter
frames displace the rest of the headers and need to use the generic flow
dissector procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:13 +0000 (22:32 +0300)]
net: dsa: tag_qca: use the generic flow dissector procedure
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: John Crispin <john@phrozen.org> Cc: Alexander Lobakin <alobakin@pm.me> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:12 +0000 (22:32 +0300)]
net: dsa: tag_mtk: use the generic flow dissector procedure
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: DENG Qingfang <dqfext@gmail.com> Cc: Sean Wang <sean.wang@mediatek.com> Cc: John Crispin <john@phrozen.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:11 +0000 (22:32 +0300)]
net: dsa: tag_edsa: use the generic flow dissector procedure
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:10 +0000 (22:32 +0300)]
net: dsa: tag_dsa: use the generic flow dissector procedure
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:09 +0000 (22:32 +0300)]
net: dsa: tag_brcm: use generic flow dissector procedure
There are 2 Broadcom tags in use, one places the DSA tag before the
Ethernet destination MAC address, and the other before the EtherType.
Nonetheless, both displace the rest of the headers, so this tagger can
use the generic flow dissector procedure which accounts for that.
The ASCII art drawing is a good reference though, so keep it but move it
somewhere else.
Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:08 +0000 (22:32 +0300)]
net: flow_dissector: avoid indirect call to DSA .flow_dissect for generic case
With the recent mitigations against speculative execution exploits,
indirect function calls are more expensive and it would be good to avoid
them where possible.
In the case of DSA, most switch taggers will shift the EtherType and
next headers by a fixed amount equal to that tag's length in bytes.
So we can use a generic procedure to determine that, without calling
into custom tagger code. However we still leave the flow_dissect method
inside struct dsa_device_ops as an override for the generic function.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:07 +0000 (22:32 +0300)]
net: dsa: point out the tail taggers
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:06 +0000 (22:32 +0300)]
net: dsa: add a generic procedure for the flow dissector
For all DSA formats that don't use tail tags, it looks like behind the
obscure number crunching they're all doing the same thing: locating the
real EtherType behind the DSA tag. Nonetheless, this is not immediately
obvious, so create a generic helper for those DSA taggers that put the
header before the EtherType.
Another assumption for the generic function is that the DSA tags are of
equal length on RX and on TX. Prior to the previous patch, this was not
true for ocelot and for gswip. The problem was resolved for ocelot, but
for gswip it still remains, so that can't use this helper yet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:05 +0000 (22:32 +0300)]
net: dsa: make the .flow_dissect tagger callback return void
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:04 +0000 (22:32 +0300)]
net: dsa: tag_ocelot: use a short prefix on both ingress and egress
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:03 +0000 (22:32 +0300)]
net: dsa: tag_sja1105: request promiscuous mode for master
Currently PTP is broken when ports are in standalone mode (the tagger
keeps printing this message):
sja1105 spi0.1: Expected meta frame, is 01-80-c2-00-00-0e in the DSA master multicast filter?
Sure, one might say "simply add 01-80-c2-00-00-0e to the master's RX
filter" but things become more complicated because:
- Actually all frames in the 01-80-c2-xx-xx-xx and 01-1b-19-xx-xx-xx
range are trapped to the CPU automatically
- The switch mangles bytes 3 and 4 of the MAC address via the incl_srcpt
("include source port [in the DMAC]") option, which is how source port
and switch id identification is done for link-local traffic on RX. But
this means that an address installed to the RX filter would, at the
end of the day, not correspond to the final address seen by the DSA
master.
Assume RX filtering lists on DSA masters are typically too small to
include all necessary addresses for PTP to work properly on sja1105, and
just request promiscuous mode unconditionally.
Just an example:
Assuming the following addresses are trapped to the CPU:
01-80-c2-00-00-00 to 01-80-c2-00-00-ff
01-1b-19-00-00-00 to 01-1b-19-00-00-ff
These are 512 addresses.
Now let's say this is a board with 3 switches, and 4 ports per switch.
The 512 addresses become 6144 addresses that must be managed by the DSA
master's RX filtering lists.
This may be refined in the future, but for now, it is simply not worth
it to add the additional addresses to the master's RX filter, so simply
request it to become promiscuous as soon as the driver probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:02 +0000 (22:32 +0300)]
net: dsa: allow drivers to request promiscuous mode on master
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 26 Sep 2020 19:32:01 +0000 (22:32 +0300)]
net: mscc: ocelot: move NPI port configuration to DSA
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing prevents user from sending frames to "external" VxLAN devices.
In fact kernel itself may generate icmp chatter.
This is fine, such frames should be dropped.
The point of the "missing encapsulation" warning was that
frames with missing encap should not make it into vxlan_xmit_one().
And vxlan_xmit() drops them cleanly, so let it just do that.
Without this revert the warning is triggered by the udp_tunnel_nic.sh
test, but the minimal repro is:
$ ip link add vxlan0 type vxlan \
group 239.1.1.1 \
dev lo \
dstport 1234 \
external
$ ip li set dev vxlan0 up
This series introduces support for a new attribute to the flash update
command: DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK.
This attribute is a bitfield which allows userspace to specify what set of
subfields to overwrite when performing a flash update for a device.
The intention is to support the ability to control the behavior of
overwriting the configuration and identifying fields in the Intel ice device
flash update process. This is necessary as the firmware layout for the ice
device includes some settings and configuration within the same flash
section as the main firmware binary.
This series, and the accompanying iproute2 series, introduce support for the
attribute. Once applied, the overwrite support can be be invoked via
devlink:
# overwrite identifiers and settings
devlink dev flash pci/0000:af:00.0 file firmware.bin overwrite settings overwrite identifiers
To aid in the safe addition of new parameters, first some refactoring is
done to the .flash_update function: its parameters are converted from a
series of function arguments into a structure. This makes it easier to add
the new parameter without changing the signature of the .flash_update
handler in the future. Additionally, a "supported_flash_update_params" field
is added to devlink_ops. This field is similar to the ethtool
"supported_coalesc_params" field. The devlink core will now check that the
DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT bit is set before forwarding the
component attribute. Similarly, the new overwrite attribute will also
require a supported bit.
Doing these refactors will aid in adding any other attributes in the future,
and creates a good pattern for other interfaces to use in the future. By
requiring drivers to opt-in, we reduce the risk of accidentally breaking
drivers when ever we add an additional parameter. We also reduce boiler
plate code in drivers which do not support the parameters.
Changes since v9:
* rebased to current net-next, no other changes
Changes since v7
* resend, hopefully avoiding the SMTP server issues I experienced on Friday
Changes since v6
* Rebased to current net-next to resolve conflicts
* Added changes to the ionic driver that recently merged flash update support
* Fixed the changes for mlxsw to apply to core instead of spectrum.c after
the recent refactor.
* Picked up the review tags from Jakub
Changes since v5
* Fix *all* of the BIT usage to use _BITUL() (thanks Jakub!)
Changes since v4
* Renamed nla_overwrite to nla_overwrite_mask at Jiri's suggestion
* Added "by this device" to the netlink error messages for unsupported
attributes
* Removed use of BIT() in the uapi header
* Fixed the commit message for the netdevsim patch
* Picked up Jakub's reviewed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Fri, 25 Sep 2020 20:46:09 +0000 (13:46 -0700)]
ice: add support for flash update overwrite mask
Support the recently added DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK
parameter in the ice flash update handler. Convert the overwrite mask
bitfield into the appropriate preservation level used by the firmware
when updating.
Because there is no equivalent preservation level for overwriting only
identifiers, this combination is rejected by the driver as not supported
with an appropriate extended ACK message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log