Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a676 ("net: dsa: mv88e6xxx: Monitor and Management tables") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Many drivers call skb_reset_mac_header() before using it,
but others do not.
Commit 6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
attempted to fix this generically, but commit d346a3fae3ff
("packet: introduce PACKET_QDISC_BYPASS socket option") brought
back the macvlan bug.
Lets add a new helper, so that tx paths no longer have
to call skb_reset_mac_header() only to get a pointer
to skb->data.
Hopefully we will be able to revert 6d1ccff62780
("net: reset mac header in dev_start_xmit()") and save few cycles
in transmit fast path.
BUG: KASAN: use-after-free in __get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
BUG: KASAN: use-after-free in mc_hash drivers/net/macvlan.c:251 [inline]
BUG: KASAN: use-after-free in macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
Read of size 4 at addr ffff8880a4932401 by task syz-executor947/9579
Fixes: b863ceb7ddce ("[NET]: Add macvlan driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
WARNING: bad unlock balance detected!
5.5.0-rc5-syzkaller #0 Not tainted
-------------------------------------
syz-executor921/9688 is trying to release lock (sk_lock-AF_INET6) at:
[<ffffffff84bf8506>] gtp_encap_enable_socket+0x146/0x400 drivers/net/gtp.c:830
but there are no more locks to release!
other info that might help us debug this:
2 locks held by syz-executor921/9688:
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:72 [inline]
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x405/0xaf0 net/core/rtnetlink.c:5421
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: spin_lock_bh include/linux/spinlock.h:343 [inline]
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2951
If lockdown is disabling tracing on boot up, it prevents the tracing files
from even bering created. But when that happens, there's several places that
will give a warning that the files were not created as that is usually a
sign of a bug.
Add in strategic locations where a check is made to see if tracing is
disabled by lockdown, and if it is, do not go further, and fail silently
(but print that tracing is disabled by lockdown, without doing a WARN_ON()).
Cc: Matthew Garrett <mjg59@google.com> Fixes: 17911ff38aa5 ("tracing: Add locked_down checks to the open calls of files created for tracefs") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
There is no a_r3, a_r4 in the testing topology.
It should be b_r1, b_r2. Also b_r1 mtu is 1400 and b_r2 mtu is 1500.
Fixes: e44e428f59e4 ("selftests: pmtu: add basic IPv4 and IPv6 PMTU tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.
To fix the error, simply remove the conditional operator.
A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.
Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fixes: d66cb37e9664 ("qeth: Add new priority queueing options") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.
But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.
Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Under heavy loads where the kyber I/O scheduler hits the token limits for
its scheduling domains, kyber can become stuck. When active requests
complete, kyber may not be woken up leaving the I/O requests in kyber
stuck.
This stuck state is due to a race condition with kyber and the sbitmap
functions it uses to run a callback when enough requests have completed.
The running of a sbt_wait callback can race with the attempt to insert the
sbt_wait. Since sbitmap_del_wait_queue removes the sbt_wait from the list
first then sets the sbq field to NULL, kyber can see the item as not on a
list but the call to sbitmap_add_wait_queue will see sbq as non-NULL. This
results in the sbt_wait being inserted onto the wait list but ws_active
doesn't get incremented. So the sbitmap queue does not know there is a
waiter on a wait list.
Since sbitmap doesn't think there is a waiter, kyber may never be
informed that there are domain tokens available and the I/O never advances.
With the sbt_wait on a wait list, kyber believes it has an active waiter
so cannot insert a new waiter when reaching the domain's full state.
This race can be fixed by only adding the sbt_wait to the queue if the
sbq field is NULL. If sbq is not NULL, there is already an action active
which will trigger the re-running of kyber. Let it run and add the
sbt_wait to the wait list if still needing to wait.
Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Jeffery <djeffery@redhat.com> Reported-by: John Pittman <jpittman@redhat.com> Tested-by: John Pittman <jpittman@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fix this compiler warning:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
arch/parisc/include/asm/cmpxchg.h:48:3: warning: value computed is not used [-Wunused-value]
48 | ((__typeof__(*(ptr)))__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))))
arch/parisc/include/asm/atomic.h:78:30: note: in expansion of macro ‘xchg’
78 | #define atomic_xchg(v, new) (xchg(&((v)->counter), new))
| ^~~~
kernel/debug/debug_core.c:596:4: note: in expansion of macro ‘atomic_xchg’
596 | atomic_xchg(&kgdb_active, cpu);
| ^~~~~~~~~~~
Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If __blk_rq_map_user_iov() is failed in blk_rq_map_user_iov(),
the bio(s) which is allocated before this failing will leak. The
refcount of the bio(s) is init to 1 and increased to 2 by calling
bio_get(), but __blk_rq_unmap_user() only decrease it to 1, so
the bio cannot be freed. Fix it by calling blk_rq_unmap_user().
Reviewed-by: Bob Liu <bob.liu@oracle.com> Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If for whatever reason the dasd_eckd_check_characteristics() function
exits after at least some paths have their configuration data
allocated those data is never freed again. In the error case the
device->private pointer is set to NULL and dasd_eckd_uncheck_device()
will exit without freeing the path data because of this NULL pointer.
Fix by calling dasd_eckd_clear_conf_data() for error cases.
Also use dasd_eckd_clear_conf_data() in dasd_eckd_uncheck_device()
to avoid code duplication.
Reported-by: Qian Cai <cai@lca.pw> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The max data count (mdc) is an unsigned 16-bit integer value as per AR
documentation and is received via ccw_device_get_mdc() for a specific
path mask from the CIO layer. The function itself also always returns a
positive mdc value or 0 in case mdc isn't supported or couldn't be
determined.
Though, the comment for this function describes a negative return value
to indicate failures.
As a result, the DASD device driver interprets the return value of
ccw_device_get_mdc() incorrectly. The error case is essentially a dead
code path.
To fix this behaviour, check explicitly for a return value of 0 and
change the comment for ccw_device_get_mdc() accordingly.
This fix merely enables the error code path in the DASD functions
get_fcx_max_data() and verify_fcx_max_data(). The actual functionality
stays the same and is still correct.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
HiSilicon Taishan v110 CPUs didn't implement CSV2 field of the
ID_AA64PFR0_EL1, but spectre-v2 is mitigated by hardware, so
whitelist the MIDR in the safe list.
Signed-off-by: Wei Li <liwei391@huawei.com>
[hanjun: re-write the commit log] Signed-off-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The mapping entry has to hold the GPIO line index instead of
controller's register number.
Fixes: 5037d4ddda31 ("platform/x86: pcengines-apuv2: wire up simswitch gpio as led") Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN.
2. After switching the XDP program, call synchronize_rcu to let
ixgbe_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down.
4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware
resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to
avoid using the XDP ring when it's already destroyed. synchronize_rcu is
called from ixgbe_txrx_ring_disable.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
After disabling resources necessary for XSK (the XDP program, channels,
XSK queues), use synchronize_rcu to wait until the XSK wakeup function
finishes, before freeing the resources.
Suspend XSK wakeups during switching channels. If the XDP program is
being removed, synchronize_rcu before closing the old channels to allow
XSK wakeup to complete.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The XSK wakeup callback in drivers makes some sanity checks before
triggering NAPI. However, some configuration changes may occur during
this function that affect the result of those checks. For example, the
interface can go down, and all the resources will be destroyed after the
checks in the wakeup function, but before it attempts to use these
resources. Wrap this callback in rcu_read_lock to allow driver to
synchronize_rcu before actually destroying the resources.
xsk_wakeup is a new function that encapsulates calling ndo_xsk_wakeup
wrapped into the RCU lock. After this commit, xsk_poll starts using
xsk_wakeup and checks xs->zc instead of ndo_xsk_wakeup != NULL to decide
ndo_xsk_wakeup should be called. It also fixes a bug introduced with the
need_wakeup feature: a non-zero-copy socket may be used with a driver
supporting zero-copy, and in this case ndo_xsk_wakeup should not be
called, so the xs->zc check is the correct one.
Fixes: 77cd0d7b3f25 ("xsk: add support for need_wakeup flag in AF_XDP rings") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191217162023.16011-2-maximmi@mellanox.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
the purgatory must not rely on functions from the "old" kernel,
so we must disable kasan and friends. We also need to have a
separate copy of string.c as the default does not build memcmp
with KASAN.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be11 ("stmmac: add the initial tx coalesce schema") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
A recent addition exposed a helper that is only used for CONFIG_OF. Move
it into the CONFIG_OF zone in this file to make the compiler stop
warning about an unused function.
Fixes: 66d9506440bb ("clk: walk orphan list on clock provider registration") Signed-off-by: Olof Johansson <olof@lixom.net> Link: https://lkml.kernel.org/r/20191217082501.424892072D@mail.kernel.org
[sboyd@kernel.org: "Simply" move the function instead] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
There is no reliable way to submit and wait in a single syscall, as
io_submit_sqes() may under-consume sqes (in case of an early error).
Then it will wait for not-yet-submitted requests, deadlocking the user
in most cases.
Don't wait/poll if can't submit all sqes
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Since commit ece6e6f0218b ("iommu/dma-iommu: Split iommu_dma_map_msi_msg()
in two parts"), iommu_dma_prepare_msi() should no longer have to worry
about preempting itself, nor being called in atomic context at all. Thus
we can downgrade the IRQ-safe locking to a simple mutex to avoid angering
the new might_sleep() check in iommu_map().
Reported-by: Qian Cai <cai@lca.pw> Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In smmu_pmu_probe(), there is put_cpu() in the error path,
which is wrong because we use raw_smp_processor_id() to
get the cpu ID, not get_cpu(), remove it.
While we are at it, kill 'out_cpuhp_err' altogether and
just return err if we fail to add the hotplug instance.
Acked-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When a filesystem is unmounted, we currently call fsnotify_sb_delete()
before evict_inodes(), which means that fsnotify_unmount_inodes()
must iterate over all inodes on the superblock looking for any inodes
with watches. This is inefficient and can lead to livelocks as it
iterates over many unwatched inodes.
At this point, SB_ACTIVE is gone and dropping refcount to zero kicks
the inode out out immediately, so anything processed by
fsnotify_sb_delete / fsnotify_unmount_inodes gets evicted in that loop.
After that, the call to evict_inodes will evict everything else with a
zero refcount.
This should speed things up overall, and avoid livelocks in
fsnotify_unmount_inodes().
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Anything that walks all inodes on sb->s_inodes list without rescheduling
risks softlockups.
Previous efforts were made in 2 functions, see:
c27d82f fs/drop_caches.c: avoid softlockups in drop_pagecache_sb() ac05fbb inode: don't softlockup when evicting inodes
but there hasn't been an audit of all walkers, so do that now. This
also consistently moves the cond_resched() calls to the bottom of each
loop in cases where it already exists.
One loop remains: remove_dquot_ref(), because I'm not quite sure how
to deal with that one w/o taking the i_lock.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
drivers/usb/typec/tcpm/fusb302.o: In function `tcpm_get_current_limit':
fusb302.c:(.text+0x3ee): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x422): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x450): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x48c): undefined reference to `extcon_get_state'
drivers/usb/typec/tcpm/fusb302.o: In function `fusb302_probe':
fusb302.c:(.text+0x980): undefined reference to `extcon_get_extcon_dev'
make: *** [vmlinux] Error 1
It is because EXTCON is build as a module, but FUSB302 is not.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: zhong jiang <zhongjiang@huawei.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/1576239378-50795-1-git-send-email-zhongjiang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The psi window size is a u64 an can be up to 10 seconds right now,
which exceeds the lower 32 bits of the variable. We currently use
div_u64 for it, which is meant only for 32-bit divisors. The result is
garbage pressure sampling values and even potential div0 crashes.
Use div64_u64.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Suren Baghdasaryan <surenb@google.com> Cc: Jingfeng Xie <xiejingfeng@linux.alibaba.com> Link: https://lkml.kernel.org/r/20191203183524.41378-3-hannes@cmpxchg.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The crashing instruction is trying to divide the observed stall time
by the sampling period. The period, stored in R8, is not 0, but we are
dividing by the lower 32 bits only, which are all 0 in this instance.
We could switch to a 64-bit division, but the period shouldn't be that
big in the first place. It's the time between the last update and the
next scheduled one, and so should always be around 2s and comfortably
fit into 32 bits.
The bug is in the initialization of new cgroups: we schedule the first
sampling event in a cgroup as an offset of sched_clock(), but fail to
initialize the last_update timestamp, and it defaults to 0. That
results in a bogusly large sampling period the first time we run the
sampling code, and consequently we underreport pressure for the first
2s of a cgroup's life. But worse, if sched_clock() is sufficiently
advanced on the system, and the user gets unlucky, the period's lower
32 bits can all be 0 and the sampling division will crash.
Fix this by initializing the last update timestamp to the creation
time of the cgroup, thus correctly marking the start of the first
pressure sampling period in a new cgroup.
Reported-by: Jingfeng Xie <xiejingfeng@linux.alibaba.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Suren Baghdasaryan <surenb@google.com> Link: https://lkml.kernel.org/r/20191203183524.41378-2-hannes@cmpxchg.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
ccbebba4c6bf ("perf/x86/intel/pt: Bypass PT vs. LBR exclusivity if the core supports it")
skips the PT/LBR exclusivity check on CPUs where PT and LBRs coexist, but
also inadvertently skips the active_events bump for PT in that case, which
is a bug. If there aren't any hardware events at the same time as PT, the
PMI handler will ignore PT PMIs, as active_events reads zero in that case,
resulting in the "Uhhuh" spurious NMI warning and PT data loss.
Fix this by always increasing active_events for PT events.
Fixes: ccbebba4c6bf ("perf/x86/intel/pt: Bypass PT vs. LBR exclusivity if the core supports it") Reported-by: Vitaly Slobodskoy <vitaly.slobodskoy@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Link: https://lkml.kernel.org/r/20191210105101.77210-1-alexander.shishkin@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
UBSAN reported out-of-bound accesses for x86_pmu.event_map(), it's
arguments should be < x86_pmu.max_events. Make sure all users observe
this constraint.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
NULL expressions are taken to always be true, as implemented by the
expr_is_yes() macro and by several other functions in expr.c. As such,
they ought to be valid inputs to expr_eq(), which compares two
expressions.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The reason:
When alloc_iova_mem() without initial with Zero, sometimes fpn_lo will
equal to IOVA_ANCHOR by chance, so when return with -ENOMEM(iova32_full)
from __alloc_and_insert_iova_range(), the new_iova will not be freed in
free_iova_mem().
Fixes: bb68b2fbfbd6 ("iommu/iova: Add rbtree anchor node") Signed-off-by: Xiaotao Yin <xiaotao.yin@windriver.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Currently CONFIG_XIL_AXIS_FIFO=y implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/staging/axis-fifo/axis-fifo.o: in function `axis_fifo_probe':
drivers/staging/axis-fifo/axis-fifo.c:809: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Lockdep warns about a possible circular locking dependency because using
syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.
Use the recently introduced device_node_to_regmap to solve that as it looks
up the regmap in the same list but doesn't care about the clocks.
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lkml.kernel.org/r/20191128102531.817549-1-alexandre.belloni@bootlin.com Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller") Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
platform device aliases were missing, preventing
autoloading of module.
Fixes: 811b700630ff ("regulator: rn5t618: add driver for Ricoh RN5T618 regulators") Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Link: https://lore.kernel.org/r/20191211221600.29438-1-andreas@kemnade.info Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e29 ("ASoC: Add initial WM8962 CODEC driver") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In rfkill_register, the struct rfkill pointer is first derefernced
and then checked for NULL. This patch removes the BUG_ON and returns
an error to the caller in case rfkill is NULL.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Link: https://lore.kernel.org/r/20191215153409.21696-1-pakki001@umn.edu Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
MODPOST vmlinux.o
WARNING: vmlinux.o(.text.unlikely+0xa0c): Section mismatch in reference from the function walk_lower_bus() to the function .init.text:walk_native_bus()
The function walk_lower_bus() references
the function __init walk_native_bus().
This is often because walk_lower_bus lacks a __init
annotation or the annotation of walk_native_bus is wrong.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
drivers/misc/habanalabs/goya/goya.c: In function goya_pldm_init_cpu:
drivers/misc/habanalabs/goya/goya.c:2195:6: warning: variable val set but not used [-Wunused-but-set-variable]
drivers/misc/habanalabs/goya/goya.c: In function goya_hw_init:
drivers/misc/habanalabs/goya/goya.c:2505:6: warning: variable val set but not used [-Wunused-but-set-variable]
In case a user submits a CS, and the submission fails, and the user doesn't
check the return value and instead use the error return value as a valid
sequence number of a CS and ask to wait on it, the driver will print an
error and return an error code for that wait.
The real problem happens if now the user ignores the error of the wait, and
try to wait again and again. This can lead to a flood of error messages
from the driver and even soft lockup event.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com> Reviewed-by: Tomer Tayar <ttayar@habana.ai> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Redirecting a packet from ingress to egress by using bpf_redirect
breaks if the egress interface has an fq qdisc installed. This is the same
problem as fixed in 'commit 8203e2d844d3 ("net: clear skb->tstamp in forwarding paths")
Clear skb->tstamp when redirecting into the egress path.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.") Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: Lorenz Bauer <lmb@cloudflare.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/bpf/20191213180817.2510-1-lmb@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Normally when cloning a file range if we find an implicit hole at the end
of the range we assume it is because the NO_HOLES feature is enabled.
However that is not always the case. One well known case [1] is when we
have a power failure after mixing buffered and direct IO writes against
the same file.
In such cases we need to punch a hole in the destination file, and if
the NO_HOLES feature is not enabled, we need to insert explicit file
extent items to represent the hole. After commit 690a5dbfc51315
("Btrfs: fix ENOSPC errors, leading to transaction aborts, when cloning
extents"), we started to insert file extent items representing the hole
with an item size of 0, which is invalid and should be 53 bytes (the size
of a btrfs_file_extent_item structure), resulting in all sorts of
corruptions and invalid memory accesses. This is detected by the tree
checker when we attempt to write a leaf to disk.
The problem can be sporadically triggered by test case generic/561 from
fstests. That test case does not exercise power failure and creates a new
filesystem when it starts, so it does not use a filesystem created by any
previous test that tests power failure. However the test does both
buffered and direct IO writes (through fsstress) and it's precisely that
which is creating the implicit holes in files. That happens even before
the commit mentioned earlier. I need to investigate why we get those
implicit holes to check if there is a real problem or not. For now this
change fixes the regression of introducing file extent items with an item
size of 0 bytes.
Fix the issue by calling btrfs_punch_hole_range() without passing a
btrfs_clone_extent_info structure, which ensures file extent items are
inserted to represent the hole with a correct item size. We were passing
a btrfs_clone_extent_info with a value of 0 for its 'item_size' field,
which was causing the insertion of file extent items with an item size
of 0.
Reported-by: David Sterba <dsterba@suse.com> Fixes: 690a5dbfc51315 ("Btrfs: fix ENOSPC errors, leading to transaction aborts, when cloning extents") Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We have a BUG_ON(ret < 0) in find_free_extent from
btrfs_cache_block_group. If we fail to allocate our ctl we'll just
panic, which is not good. Instead just go on to another block group.
If we fail to find a block group we don't want to return ENOSPC, because
really we got a ENOMEM and that's the root of the problem. Save our
return from btrfs_cache_block_group(), and then if we still fail to make
our allocation return that ret so we get the right error back.
Tested with inject-error.py from bcc.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Recently, the spinlock implementation grew a static key optimization,
but the jump_label.h header include was left out, leading to build
errors:
linux/arch/powerpc/include/asm/spinlock.h:44:7: error: implicit declaration of function ‘static_branch_unlikely’
44 | if (!static_branch_unlikely(&shared_processor))
This commit adds the missing header.
mpe: The build break is only seen with CONFIG_JUMP_LABEL=n.
Fixes: 656c21d6af5d ("powerpc/shared: Use static key to detect shared processor") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Srikar Dronamraju <srikar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191223133147.129983-1-Jason@zx2c4.com Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
With commit 247f2f6f3c70 ("sched/core: Don't schedule threads on
pre-empted vCPUs"), the scheduler avoids preempted vCPUs to schedule
tasks on wakeup. This leads to wrong choice of CPU, which in-turn
leads to larger wakeup latencies. Eventually, it leads to performance
regression in latency sensitive benchmarks like soltp, schbench etc.
On Powerpc, vcpu_is_preempted() only looks at yield_count. If the
yield_count is odd, the vCPU is assumed to be preempted. However
yield_count is increased whenever the LPAR enters CEDE state (idle).
So any CPU that has entered CEDE state is assumed to be preempted.
Even if vCPU of dedicated LPAR is preempted/donated, it should have
right of first-use since they are supposed to own the vCPU.
On a Power9 System with 32 cores:
# lscpu
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 128
On-line CPU(s) list: 0-127
Thread(s) per core: 8
Core(s) per socket: 1
Socket(s): 16
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-63
NUMA node1 CPU(s): 64-127
Fixes: 247f2f6f3c70 ("sched/core: Don't schedule threads on pre-empted vCPUs") Cc: stable@vger.kernel.org # v4.18+ Reported-by: Parth Shah <parth@linux.ibm.com> Reported-by: Ihor Pasichnyk <Ihor.Pasichnyk@ibm.com> Tested-by: Juri Lelli <juri.lelli@redhat.com> Acked-by: Waiman Long <longman@redhat.com> Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Phil Auld <pauld@redhat.com> Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.ibm.com> Tested-by: Parth Shah <parth@linux.ibm.com>
[mpe: Move the key and setting of the key to pseries/setup.c] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191213035036.6913-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When using the NO_HOLES feature if we clone a range that contains a hole
and a temporary ENOSPC happens while dropping extents from the target
inode's range, we can end up failing and aborting the transaction with
-EEXIST or with a corrupt file extent item, that has a length greater
than it should and overlaps with other extents. For example when cloning
the following range from inode A to inode B:
Target range: [1MB, 6MB) (same as source, to make it easier to explain)
The following can happen:
1) btrfs_punch_hole_range() gets -ENOSPC from __btrfs_drop_extents();
2) At that point, 'cur_offset' is set to 1MB and __btrfs_drop_extents()
set 'drop_end' to 2MB, meaning it was able to drop only extent B2;
3) We then compute 'clone_len' as 'drop_end' - 'cur_offset' = 2MB - 1MB =
1MB;
4) We then attempt to insert a file extent item at inode B with a file
offset of 5MB, which is the value of clone_info->file_offset. This
fails with error -EEXIST because there's already an extent at that
offset (extent B4);
5) We abort the current transaction with -EEXIST and return that error
to user space as well.
Target range: [1MB, 12MB) (same as source, to make it easier to explain)
1) btrfs_punch_hole_range() gets -ENOSPC from __btrfs_drop_extents();
2) At that point, 'cur_offset' is set to 1MB and __btrfs_drop_extents()
set 'drop_end' to 5MB, meaning it was able to drop only extent B2;
3) We then compute 'clone_len' as 'drop_end' - 'cur_offset' = 5MB - 1MB =
4MB;
4) We then insert a file extent item at inode B with a file offset of 11MB
which is the value of clone_info->file_offset, and a length of 4MB (the
value of 'clone_len'). So we get 2 extents items with ranges that
overlap and an extent length of 4MB, larger then the extent A2 from
inode A (1MB length);
5) After that we end the transaction, balance the btree dirty pages and
then start another or join the previous transaction. It might happen
that the transaction which inserted the incorrect extent was committed
by another task so we end up with extent corruption if a power failure
happens.
So fix this by making sure we attempt to insert the extent to clone at
the destination inode only if we are past dropping the sub-range that
corresponds to a hole.
Fixes: 690a5dbfc51315 ("Btrfs: fix ENOSPC errors, leading to transaction aborts, when cloning extents") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The branch of qgroup_rescan_init which is executed from the mount
path prints wrong errors messages. The textual print out in case
BTRFS_QGROUP_STATUS_FLAG_RESCAN/BTRFS_QGROUP_STATUS_FLAG_ON are not
set are transposed. Fix it by exchanging their place.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Some powerpc platforms (e.g. 85xx) limit DMA-able memory way below 4G.
If a system has more physical memory than this limit, the swiotlb
buffer is not addressable because it is allocated from memblock using
top-down mode.
Force memblock to bottom-up mode before calling swiotlb_init() to
ensure that the swiotlb buffer is DMA-able.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191204123524.22919-1-rppt@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This commit adds a check on ops pointer to avoid a kernel panic when
ops->strict is used. Indeed, on some pinctrl driver (at least for
pinctrl-stmfx) the pinmux ops is not implemented. Let's assume than gpio
can be used in this case.
Fixes: 472a61e777fe ("pinctrl/gpio: Take MUX usage into account") Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Link: https://lore.kernel.org/r/20191204144106.10876-1-alexandre.torgue@st.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If wdev->wext.keys was initialized it didn't get reset to NULL on
unregister (and it doesn't get set in cfg80211_init_wdev either), but
wdev is reused if unregister was triggered through
cfg80211_switch_netns.
The next unregister (for whatever reason) will try to free
wdev->wext.keys again.
Fix overwriting of the qos_ctrl.tid field for encrypted frames injected on
a monitor interface. While qos_ctrl.tid is not encrypted, it's used as an
input into the encryption algorithm so it's protected, and thus cannot be
modified after encryption. For injected frames, the encryption may already
have been done in userspace, so we cannot change any fields.
Before passing the frame to the driver, the qos_ctrl.tid field is updated
from skb->priority. Prior to dbd50a851c50 skb->priority was updated in
ieee80211_select_queue_80211(), but this function is no longer always
called.
Update skb->priority in ieee80211_monitor_start_xmit() so that the value
is stored, and when later code 'modifies' the TID it really sets it to
the same value as before, preserving the encryption.
Fixes: dbd50a851c50 ("mac80211: only allocate one queue when using iTXQs") Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Link: https://lore.kernel.org/r/20191119133451.14711-1-fredrik.olofsson@anyfinetworks.com
[rewrite commit message based on our discussion] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
So far, we walked the orphan list every time a new clock was registered
in CCF. This was fine since the clocks were only referenced by name.
Now that the clock can be referenced through DT, it is not enough:
* Controller A register first a reference clocks from controller B
through DT.
* Controller B register all its clocks then register the provider.
Each time controller B registers a new clock, the orphan list is walked
but it can't match since the provider is registered yet. When the
provider is finally registered, the orphan list is not walked unless
another clock is registered afterward.
This can lead to situation where some clocks remain orphaned even if
the parent is available.
Walking the orphan list on provider registration solves the problem.
Reported-by: Jian Hu <jian.hu@amlogic.com> Fixes: fc0c209c147f ("clk: Allow parents to be specified without string names") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lkml.kernel.org/r/20191203080805.104628-1-jbrunet@baylibre.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We have dts property for "ti,sysc-delay-us", and we're using it, but the
wait after OCP softreset only happens if devices are probed in legacy mode.
Let's add a delay after writing the OCP softreset when specified.
Fixes: e0db94fe87da ("bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits") Cc: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Early revisions of the AST2600 datasheet are conflicted about the state
of the LPC/eSPI strapping bit (SCU510[6]). Conversations with ASPEED
determined that the reference pinmux configuration tables were in error
and the SCU documentation contained the correct configuration. Update
the driver to reflect the state described in the SCU documentation.
Fixes: 2eda1cdec49f ("pinctrl: aspeed: Add AST2600 pinmux support") Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20191202050110.15340-1-andrew@aj.id.au Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The reboot register isn't located inside the DCFG controller, but in its
own RST controller. Fix it.
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC") Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Currently, open() is called from the user program and it calls the syscall
'sys_openat', not the 'sys_open'. This leads to an error of the program
of user side, due to the fact that the counter maps are zero since no
function such 'sys_open' is called.
This commit adds the kernel bpf program which are attached to the
tracepoint 'sys_enter_openat' and 'sys_enter_openat'.
Fixes: 1da236b6be963 ("bpf: add a test case for syscalls/sys_{enter|exit}_* tracepoints") Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Previously, when this sample is added, commit 1c47910ef8013
("samples/bpf: add perf_event+bpf example"), a symbol 'sys_read' and
'sys_write' has been used without no prefixes. But currently there are
no exact symbols with these under kallsyms and this leads to failure.
This commit changes exact compare to substring compare to keep compatible
with exact symbol or prefixed symbol.
Fixes: 1c47910ef8013 ("samples/bpf: add perf_event+bpf example") Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20191205080114.19766-2-danieltimlee@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If a timeout failure occurs, kselftest kills the test process and prints
the timeout log. If the test process has killed while printing a log
that ends with new line, the timeout log can be printed in middle of the
test process output so that it can be seems like a comment, as below:
# test_process_log not ok 3 selftests: timers: nsleep-lat # TIMEOUT
This commit avoids such problem by printing one more line before the
TIMEOUT failure log.
Signed-off-by: SeongJae Park <sjpark@amazon.de> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Before this patch, perf expected that there might be NPROC*4 unique
cache entries at max, however, it also expected that some of them would
be shared and/or of the same size, thus the final number of entries
would be reduced to be lower than NPROC*4. In case the number of entries
hadn't been reduced (was NPROC*4), the warning was printed.
However, some systems might have unusual cache topology, such as the
following two-processor KVM guest:
This KVM guest has 8 (NPROC*4) unique cache entries, which used to make
perf printing the message, although there actually aren't "way too many
cpu caches".
v2: Removing unused argument.
v3: Unifying the way we obtain number of cpus.
v4: Removed '& UINT_MAX' construct which is redundant.
Signed-off-by: Michael Petlan <mpetlan@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com>
LPU-Reference: 20191208162056.20772-1-mpetlan@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Commit f01642e4912b ("perf metricgroup: Support multiple events for
metricgroup") introduced support for multiple events in a metric group.
But with the current upstream, metric events names are not printed
properly
command:./perf stat --metric-only -M Power -I 1000
1.000579994
2.002189493
With current upstream version, issue is with event name comparison logic
in find_evsel_group(). Current logic is to compare events belonging to a
metric group to the events in perf_evlist. Since the break statement is
missing in the loop used for comparison between metric group and
perf_evlist events, the loop continues to execute even after getting a
pattern match, and end up in discarding the matches.
Incase of single metric event belongs to metric group, its working fine,
because in case of single event once it compare all events it reaches to
end of perf_evlist.
Example for single metric event in power9 platform:
This patch fixes the issue by making sure once we found all events
belongs to that metric event matched in find_evsel_group(), we
successfully break from that loop by adding corresponding condition.
When the kptr_restrict sysctl is set, the kernel can fail to return
jited_ksyms or jited_prog_insns, but still have positive values in
nr_jited_ksyms and jited_prog_len. This causes bpftool to crash when
trying to dump the program because it only checks the len fields not
the actual pointers to the instructions and ksyms.
Fix this by adding the missing checks.
Fixes: 71bb428fe2c1 ("tools: bpf: add bpftool") Fixes: f84192ee00b7 ("tools: bpftool: resolve calls without using imm field") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20191210181412.151226-1-toke@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
All BPF JIT compilers except RISC-V's and MIPS' enforce a 33-tail calls
limit at runtime. In addition, a test was recently added, in tailcalls2,
to check this limit.
This patch updates the tail call limit in MIPS' JIT compiler to allow
33 tail calls.
Fixes: b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.") Reported-by: Mahshid Khezri <khezri.mahshid@gmail.com> Signed-off-by: Paul Chaignon <paul.chaignon@orange.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/b8eb2caac1c25453c539248e56ca22f74b5316af.1575916815.git.paul.chaignon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
All BPF JIT compilers except RISC-V's and MIPS' enforce a 33-tail calls
limit at runtime. In addition, a test was recently added, in tailcalls2,
to check this limit.
This patch updates the tail call limit in RISC-V's JIT compiler to allow
33 tail calls. I tested it using the above selftest on an emulated
RISCV64.
Fixes: 2353ecc6f91f ("bpf, riscv: add BPF JIT for RV64G") Reported-by: Mahshid Khezri <khezri.mahshid@gmail.com> Signed-off-by: Paul Chaignon <paul.chaignon@orange.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Björn Töpel <bjorn.topel@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/966fe384383bf23a0ee1efe8d7291c78a3fb832b.1575916815.git.paul.chaignon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181cc4 ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Commit 0e4a459f56c3 ("tracing: Remove unnecessary DEBUG_FS dependency")
removed select for DEBUG_FS but we still need it at least for enabling
deeper idle states for the SoCs.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The phy mode should be rgmii-id. For some reason, it used to work with
rgmii-txid but doesn't any more.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Added warning log when found some unknown FW boot ext header,
to improve debuggability.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191210004854.16845-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The return value of soc_tplg_pcm_create() is currently not checked
in soc_tplg_pcm_elems_load(). If an error is to occur there, the
topology ignores it and continues loading.
Fix that by checking the status and rejecting the topology on error.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191210003939.15752-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
snd_soc_add_dai_link() might fail. This situation occurs for
instance in a very specific use case where a PCM device and a
Back End DAI link are given identical names in the topology.
When this happens, soc_new_pcm_runtime() fails and then
snd_soc_add_dai_link() returns -ENOMEM when called from
soc_tplg_fe_link_create(). Because of that, the link will not
get added into the card list, so any attempt to remove it later
ends up in a panic.
Fix that by checking the return status and free the memory in case
of an error.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191210003939.15752-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>