Huazhong Tan [Wed, 7 Nov 2018 04:06:11 +0000 (12:06 +0800)]
net: hns3: enable/disable ring in the enet while doing UP/DOWN
While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.
So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.
Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:10 +0000 (12:06 +0800)]
net: hns3: adjust the location of clearing the table when doing reset
When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:09 +0000 (12:06 +0800)]
net: hns3: provide some interface & information for the client
The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.
So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.
Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:08 +0000 (12:06 +0800)]
net: hns3: add set_default_reset_request in the hnae3_ae_ops
Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.
There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:07 +0000 (12:06 +0800)]
net: hns3: use HNS3_NIC_STATE_INITED to indicate the initialization state of enet
Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.
So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.
Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: systemport: Unmap queues upon DSA unregister event
This patch series fixes the unbinding/binding of the bcm_sf2 switch
driver along with bcmsysport which monitors the switch port queues.
Because the driver was not processing the DSA_PORT_UNREGISTER event, we
would not be unmapping switch port/queues, which could cause incorrect
decisions to be made by the HW (e.g: queue always back-pressured).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Unmap queues upon DSA unregister event
Binding and unbinding the switch driver which creates the DSA slave
network devices for which we set-up inspection would lead to
undesireable effects since we were not clearing the port/queue mapping
to the SYSTEMPORT TX queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Turn on PHY to allow successful registration
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: dsa: bcm_sf2: Store rules in lists
This patch series changes the bcm-sf2 driver to keep a copy of the
inserted rules as opposed to using the HW as a storage area for a number
of reasons:
- this helps us with doing duplicate rule detection in a faster way, it
would have required a full rule read before
- this helps with Pablo's on-going work to convert ethtool_rx_flow_spec
to a more generic flow rule structure by having fewer code paths to
convert to the new structure/helpers
- we need to cache copies to restore them during drive resumption,
because depending on the low power mode the system has entered, the
switch may have lost all of its context
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Restore Broadcom tag match filters upon resume
Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Get rid of unmarshalling functions
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Restore CFP rules during system resume
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Split rule handling from HW operation
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Nov 2018 23:00:45 +0000 (15:00 -0800)]
Merge branch 'net-More-extack-messages'
David Ahern says:
====================
net: More extack messages
Add more extack messages for several link create errors (e.g., invalid
number of queues, unknown link kind) and invalid metrics argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 6 Nov 2018 20:51:16 +0000 (12:51 -0800)]
rtnetlink: Add more extack messages to rtnl_newlink
Add extack arg to the nla_parse_nested calls in rtnl_newlink, and
add messages for unknown device type and link network namespace id.
In particular, it improves the failure message when the wrong link
type is used. From
$ ip li add bond1 type bonding
RTNETLINK answers: Operation not supported
to
$ ip li add bond1 type bonding
Error: Unknown device type.
(The module name is bonding but the link type is bond.)
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 2 Nov 2018 22:00:26 +0000 (15:00 -0700)]
ISDN: eicon: Remove driver
I started looking at the history of this driver, and last time the
maintainer was active on the mailing list was when discussing how to
remove it. This was in 2012:
It looks to me like this has in practice been an orphan for quite a while.
It's throwing warnings about stack size in a function that is in dire
need of refactoring, and it's probably a case of "it's time to call it".
Cc: Armin Schindler <mac@melware.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Nov 2018 16:12:10 +0000 (08:12 -0800)]
Merge tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Masami found a slight bug in his code where he transposed the
arguments of a call to strpbrk.
The reason this wasn't detected in our tests is that the only way this
would transpire is when a kprobe event with a symbol offset is
attached to a function that belongs to a module that isn't loaded yet.
When the kprobe trace event is added, the offset would be truncated
after it was parsed, and when the module is loaded, it would use the
symbol without the offset (as the nul character added by the parsing
would not be replaced with the original character)"
* tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Fix strpbrk() argument order
Linus Torvalds [Tue, 6 Nov 2018 16:10:01 +0000 (08:10 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fix from Russell King:
"Ard spotted a typo in one of the assembly files which leads to a
kernel oops when that code path is executed. Fix this"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm
1) Handle errors mid-stream of an all dump, from Alexey Kodanev.
2) Fix build of openvswitch with certain combinations of netfilter
options, from Arnd Bergmann.
3) Fix interactions between GSO and BQL, from Eric Dumazet.
4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
Hoffstätte.
5) S390 qeth driver fixes from Julian Wiedmann.
6) Allow ipv6 link local addresses for netconsole when both source and
destination are link local, from Matwey V. Kornilov.
7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.
8) Initialize mutex before use in dsa microchip driver, from Tristram
Ha.
9) Out-of-bounds access in hns3, from Yunsheng Lin.
10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
Neira Ayuso.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
net: alx: make alx_drv_name static
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
sock_diag: fix autoloading of the raw_diag module
net: core: netpoll: Enable netconsole IPv6 link local address
ipv6: properly check return value in inet6_dump_all()
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
bonding/802.3ad: fix link_failure_count tracking
net: phy: realtek: fix RTL8201F sysfs name
sctp: define SCTP_SS_DEFAULT for Stream schedulers
sctp: fix strchange_flags name for Stream Change Event
mlxsw: spectrum: Fix IP2ME CPU policer configuration
openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
qed: fix link config error handling
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
net/mlx4_en: use __netdev_tx_sent_queue()
net: do not abort bulk send on BQL status
net: bql: add __netdev_tx_sent_queue()
s390/qeth: report 25Gbit link speed
s390/qeth: sanitize ARP requests
...
Ard Biesheuvel [Mon, 5 Nov 2018 13:54:56 +0000 (14:54 +0100)]
ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm
Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.
Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:
Cc: <stable@vger.kernel.org> Fixes: 10115105cb3a ("ARM: spectre-v2: add firmware based hardening") Reviewed-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The following patchset contains the first batch of Netfilter fixes for
your net tree:
1) Fix splat with IPv6 defragmenting locally generated fragments,
from Florian Westphal.
2) Fix Incorrect check for missing attribute in nft_osf.
3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
header, from Jiri Slaby.
4) Revert map lookup in nft_numgen, this is already possible with
the existing infrastructure without this extension.
5) Fix wrong listing of set reference counter, make counter
synchronous again, from Stefano Brivio.
6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.
7) Fix allocation failure with large set, use kvcalloc().
From Andrey Ryabinin.
8) No need to disable BH when fetch ip set comment, patch from
Jozsef Kadlecsik.
9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
Taehee Yoo.
10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
from Jozsef Kadlecsik.
11) Fix setting default timeout via nfnetlink_cttimeout, this
comes with preparation patch to add nf_{tcp,udp,...}_pernet()
helper.
12) Allow ebtables table nat to be of filter type via nft_compat.
From Florian Westphal.
13) Incorrect calculation of next bucket in early_drop, do no bump
hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Mon, 5 Nov 2018 13:31:41 +0000 (22:31 +0900)]
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.
test config:
CONFIG_BPFILTER=y
# CONFIG_BPFILTER_UMH is not set
test command:
%iptables -L
iptables: No chain/target/match by that name.
Fixes: d2ba09c17a06 ("net: add skeleton of bpfilter kernel module") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei Vagin [Mon, 5 Nov 2018 06:37:15 +0000 (22:37 -0800)]
sock_diag: fix autoloading of the raw_diag module
IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.
Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Fixes: bf2ae2e4bf93 ("sock_diag: request _diag module only when the family or proto has been registered") Signed-off-by: Andrei Vagin <avagin@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 2 Nov 2018 16:11:05 +0000 (19:11 +0300)]
ipv6: properly check return value in inet6_dump_all()
Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.
Fixes: 08e814c9e8eb ("net/ipv6: Bail early if user only wants cloned entries") Fixes: ae677bbb4441 ("net: Don't return invalid table id error when dumping all families") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 2 Nov 2018 16:11:04 +0000 (19:11 +0300)]
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.
Fix it by partially restoring the previous behavior before
commit c63586dc9b3e ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.
Fixes: c63586dc9b3e ("net: rtnl_dump_all needs to propagate error from dumpit function") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Barnhill [Mon, 5 Nov 2018 20:36:45 +0000 (20:36 +0000)]
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.
Fixes: 2384d02520ff ("net/ipv6: Add anycast addresses to a global hashtable") Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
compiler: remove __no_sanitize_address_or_inline again
The __no_sanitize_address_or_inline and __no_kasan_or_inline defines
are almost identical. The only difference is that __no_kasan_or_inline
does not have the 'notrace' attribute.
To be able to replace __no_sanitize_address_or_inline with the older
definition, add 'notrace' to __no_kasan_or_inline and change to two
users of __no_sanitize_address_or_inline in the s390 code.
The 'notrace' option is necessary for e.g. the __load_psw_mask function
in arch/s390/include/asm/processor.h. Without the option it is possible
to trace __load_psw_mask which leads to kernel stack overflow.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Pointed-out-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix strpbrk()'s argument order, it must pass acceptable string
in 2nd argument. Note that this can cause a kernel panic where
it recovers backup character to code->data.
Jarod Wilson [Sun, 4 Nov 2018 19:59:46 +0000 (14:59 -0500)]
bonding/802.3ad: fix link_failure_count tracking
Commit 4d2c0cda07448ea6980f00102dc3964eb25e241c set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda0744 ("bonding: speed/duplex update at NETDEV_UP event") CC: Mahesh Bandewar <maheshb@google.com> CC: David S. Miller <davem@davemloft.net> CC: netdev@vger.kernel.org CC: stable@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 4 Nov 2018 22:46:04 +0000 (14:46 -0800)]
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Linus Torvalds [Sun, 4 Nov 2018 16:20:09 +0000 (08:20 -0800)]
Merge tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Bugfix:
- Fix build issues on architectures that don't provide 64-bit cmpxchg
Cleanups:
- Fix a spelling mistake"
* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: fix spelling mistake, EACCESS -> EACCES
SUNRPC: Use atomic(64)_t for seq_send(64)
Linus Torvalds [Sun, 4 Nov 2018 16:12:44 +0000 (08:12 -0800)]
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
Xin Long [Sat, 3 Nov 2018 06:01:31 +0000 (14:01 +0800)]
sctp: define SCTP_SS_DEFAULT for Stream schedulers
According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.
SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 3 Nov 2018 05:59:45 +0000 (13:59 +0800)]
sctp: fix strchange_flags name for Stream Change Event
As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.
To keep the compatibility, fix it by adding two macros.
Fixes: b444153fb5a6 ("sctp: add support for generating add stream change event notification") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
to not use page start but actual start instead to work correctly with
profiling e.g. finding hot instructions from stack traces. Also fix latter
with regards to dumping address and jited len for !multi prog, from Song.
2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Fri, 2 Nov 2018 19:49:15 +0000 (19:49 +0000)]
mlxsw: spectrum: Fix IP2ME CPU policer configuration
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73ce ("mlxsw: spectrum: Add policers for trap groups") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 2 Nov 2018 15:36:24 +0000 (16:36 +0100)]
qed: fix link config error handling
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7aa ("qed: Add supported link and advertise link to display in ethtool.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 4 Nov 2018 01:37:09 +0000 (18:37 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Linus Torvalds [Sun, 4 Nov 2018 01:25:17 +0000 (18:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Linus Torvalds [Sun, 4 Nov 2018 01:13:43 +0000 (18:13 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Linus Torvalds [Sun, 4 Nov 2018 01:12:09 +0000 (18:12 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
Yunsheng Lin [Fri, 2 Nov 2018 09:47:48 +0000 (17:47 +0800)]
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4b9 ("net: hns3: Fixes the back pressure setting when sriov is enabled") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 3 Nov 2018 22:40:01 +0000 (15:40 -0700)]
Merge branch 'net-bql-better-deal-with-GSO'
Eric Dumazet says:
====================
net: bql: better deal with GSO
While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.
On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.
This patch series :
- Add __netdev_tx_sent_queue() so that drivers
can implement efficient BQL and xmit_more support.
- Implement a work around in dev_hard_start_xmit()
for drivers not using __netdev_tx_sent_queue()
- changes mlx4 to use __netdev_tx_sent_queue()
v2: Tariq and Willem feedback addressed.
added __netdev_tx_sent_queue() (Willem suggestion)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 31 Oct 2018 15:39:14 +0000 (08:39 -0700)]
net/mlx4_en: use __netdev_tx_sent_queue()
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 31 Oct 2018 15:39:13 +0000 (08:39 -0700)]
net: do not abort bulk send on BQL status
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 31 Oct 2018 15:39:12 +0000 (08:39 -0700)]
net: bql: add __netdev_tx_sent_queue()
When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.
Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.
BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.
But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.
Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.
Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.
Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.
Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.
Code template in a driver might look like the following :
Linus Torvalds [Sat, 3 Nov 2018 17:55:23 +0000 (10:55 -0700)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kprobe: make page to RO mode when allocate it
arm64: kdump: fix small typo
arm64: makefile fix build of .i file in external module case
Linus Torvalds [Sat, 3 Nov 2018 17:45:55 +0000 (10:45 -0700)]
Merge tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes and updates from Steve French:
"Three small fixes (one Kerberos related, one for stable, and another
fixes an oops in xfstest 377), two helpful debugging improvements,
three patches for cifs directio and some minor cleanup"
* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix signed/unsigned mismatch on aio_read patch
cifs: don't dereference smb_file_target before null check
CIFS: Add direct I/O functions to file_operations
CIFS: Add support for direct I/O write
CIFS: Add support for direct I/O read
smb3: missing defines and structs for reparse point handling
smb3: allow more detailed protocol info on open files for debugging
smb3: on kerberos mount if server doesn't specify auth type use krb5
smb3: add trace point for tree connection
cifs: fix spelling mistake, EACCESS -> EACCES
cifs: fix return value for cifs_listxattr
David S. Miller [Sat, 3 Nov 2018 17:44:06 +0000 (10:44 -0700)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-11-02
please apply one round of qeth fixes for -net.
Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:12 +0000 (19:04 +0100)]
s390/qeth: sanitize ARP requests
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:11 +0000 (19:04 +0100)]
s390/qeth: fix initial operstate
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e3d ("s390/qeth: remove duplicated carrier state tracking") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:10 +0000 (19:04 +0100)]
s390/qeth: unregister netdevice only when registered
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e89f ("s390/qeth: allocate netdevice early") Reported-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:09 +0000 (19:04 +0100)]
s390/qeth: fix HiperSockets sniffer
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:08 +0000 (19:04 +0100)]
s390/qeth: sanitize strings in debug messages
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 3 Nov 2018 17:35:52 +0000 (10:35 -0700)]
Merge branch 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 9p fix from Al Viro:
"Regression fix for net/9p handling of iov_iter; broken by braino when
switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: Fix 9p virtio breakage
Linus Torvalds [Sat, 3 Nov 2018 17:34:03 +0000 (10:34 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mvsas: Remove set but not used variable 'id'
scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
scsi: qla2xxx: Remove a set-but-not-used variable
scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
scsi: qla2xxx: Declare local functions 'static'
scsi: qla2xxx: Improve several kernel-doc headers
scsi: qla2xxx: Modify fall-through annotations
scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
scsi: mvsas: Use dma_pool_zalloc
scsi: target: Don't request modules that aren't even built
scsi: target: Set response length for REPORT TARGET PORT GROUPS
Linus Torvalds [Sat, 3 Nov 2018 17:21:43 +0000 (10:21 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
- more ocfs2 work
- various leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
memory_hotplug: cond_resched in __remove_pages
bfs: add sanity check at bfs_fill_super()
kernel/sysctl.c: remove duplicated include
kernel/kexec_file.c: remove some duplicated includes
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2: dlmglue: clean up timestamp handling
ocfs2: don't put and assigning null to bh allocated outside
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
ocfs2: don't use iocb when EIOCBQUEUED returns
ocfs2: without quota support, avoid calling quota recovery
ocfs2: remove ocfs2_is_o2cb_active()
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
include/linux/notifier.h: SRCU: fix ctags
mm: handle no memcg case in memcg_kmem_charge() properly
It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large. Fix the issue by calling
cond_resched once per memory section.
Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa [Fri, 2 Nov 2018 22:48:42 +0000 (15:48 -0700)]
bfs: add sanity check at bfs_fill_super()
syzbot is reporting too large memory allocation at bfs_fill_super() [1].
Since file system image is corrupted such that bfs_sb->s_start == 0,
bfs_fill_super() is trying to allocate 8MB of continuous memory. Fix
this by adding a sanity check on bfs_sb->s_start, __GFP_NOWARN and
printf().
Michal Hocko [Fri, 2 Nov 2018 22:48:31 +0000 (15:48 -0700)]
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
THP allocation mode is quite complex and it depends on the defrag mode.
This complexity is hidden in alloc_hugepage_direct_gfpmask from a large
part currently. The NUMA special casing (namely __GFP_THISNODE) is
however independent and placed in alloc_pages_vma currently. This both
adds an unnecessary branch to all vma based page allocation requests and
it makes the code more complex unnecessarily as well. Not to mention
that e.g. shmem THP used to do the node reclaiming unconditionally
regardless of the defrag mode until recently. This was not only
unexpected behavior but it was also hardly a good default behavior and I
strongly suspect it was just a side effect of the code sharing more than
a deliberate decision which suggests that such a layering is wrong.
Get rid of the thp special casing from alloc_pages_vma and move the
logic to alloc_hugepage_direct_gfpmask. __GFP_THISNODE is applied to the
resulting gfp mask only when the direct reclaim is not requested and
when there is no explicit numa binding to preserve the current logic.
Please note that there's also a slight difference wrt MPOL_BIND now. The
previous code would avoid using __GFP_THISNODE if the local node was
outside of policy_nodemask(). After this patch __GFP_THISNODE is avoided
for all MPOL_BIND policies. So there's a difference that if local node
is actually allowed by the bind policy's nodemask, previously
__GFP_THISNODE would be added, but now it won't be. From the behavior
POV this is still correct because the policy nodemask is used.
Link: http://lkml.kernel.org/r/20180925120326.24392-3-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Larry Chen [Fri, 2 Nov 2018 22:48:27 +0000 (15:48 -0700)]
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2_defrag_extent() might leak allocated clusters. When the file
system has insufficient space, the number of claimed clusters might be
less than the caller wants. If that happens, the original code might
directly commit the transaction without returning clusters.
This patch is based on code in ocfs2_add_clusters_in_btree().
[akpm@linux-foundation.org: include localalloc.h, reduce scope of data_ac] Link: http://lkml.kernel.org/r/20180904041621.16874-3-lchen@suse.com Signed-off-by: Larry Chen <lchen@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 2 Nov 2018 22:48:23 +0000 (15:48 -0700)]
ocfs2: dlmglue: clean up timestamp handling
The handling of timestamps outside of the 1970..2038 range in the dlm
glue is rather inconsistent: on 32-bit architectures, this has always
wrapped around to negative timestamps in the 1902..1969 range, while on
64-bit kernels all timestamps are interpreted as positive 34 bit numbers
in the 1970..2514 year range.
Now that the VFS code handles 64-bit timestamps on all architectures, we
can make the behavior more consistent here, and return the same result
that we had on 64-bit already, making the file system y2038 safe in the
process. Outside of dlmglue, it already uses 64-bit on-disk timestamps
anway, so that part is fine.
For consistency, I'm changing ocfs2_pack_timespec() to clamp anything
outside of the supported range to the minimum and maximum values. This
avoids a possible ambiguity of values before 1970 in particular, which
used to be interpreted as times at the end of the 2514 range previously.
Link: http://lkml.kernel.org/r/20180619155826.4106487-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:19 +0000 (15:48 -0700)]
ocfs2: don't put and assigning null to bh allocated outside
ocfs2_read_blocks() and ocfs2_read_blocks_sync() are both used to read
several blocks from disk. Currently, the input argument *bhs* can be
NULL or NOT. It depends on the caller's behavior. If the function
fails in reading blocks from disk, the corresponding bh will be assigned
to NULL and put.
Obviously, above process for non-NULL input bh is not appropriate.
Because the caller doesn't even know its bhs are put and re-assigned.
If buffer head is managed by caller, ocfs2_read_blocks and
ocfs2_read_blocks_sync() should not evaluate it to NULL. It will cause
caller accessing illegal memory, thus crash.
Link: http://lkml.kernel.org/r/HK2PR06MB045285E0F4FBB561F9F2F9B3D5680@HK2PR06MB0452.apcprd06.prod.outlook.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Guozhonghua <guozhonghua@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:15 +0000 (15:48 -0700)]
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
Somehow, file system metadata was corrupted, which causes
ocfs2_check_dir_entry() to fail in function ocfs2_dir_foreach_blk_el().
According to the original design intention, if above happens we should
skip the problematic block and continue to retrieve dir entry. But
there is obviouse misuse of brelse around related code.
After failure of ocfs2_check_dir_entry(), current code just moves to
next position and uses the problematic buffer head again and again
during which the problematic buffer head is released for multiple times.
I suppose, this a serious issue which is long-lived in ocfs2. This may
cause other file systems which is also used in a the same host insane.
So we should also consider about bakcporting this patch into linux
-stable.
Link: http://lkml.kernel.org/r/HK2PR06MB045211675B43EED794E597B6D56E0@HK2PR06MB0452.apcprd06.prod.outlook.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Suggested-by: Changkuo Shi <shi.changkuo@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:11 +0000 (15:48 -0700)]
ocfs2: don't use iocb when EIOCBQUEUED returns
When -EIOCBQUEUED returns, it means that aio_complete() will be called
from dio_complete(), which is an asynchronous progress against
write_iter. Generally, IO is a very slow progress than executing
instruction, but we still can't take the risk to access a freed iocb.
And we do face a BUG crash issue. Using the crash tool, iocb is
obviously freed already.
And the backtrace shows:
ocfs2_file_write_iter+0xcaa/0xd00 [ocfs2]
aio_run_iocb+0x229/0x2f0
do_io_submit+0x291/0x540
SyS_io_submit+0x10/0x20
system_call_fastpath+0x16/0x75
Link: http://lkml.kernel.org/r/1523361653-14439-1-git-send-email-ge.changwei@h3c.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guozhonghua [Fri, 2 Nov 2018 22:48:07 +0000 (15:48 -0700)]
ocfs2: without quota support, avoid calling quota recovery
During one dead node's recovery by other node, quota recovery work will
be queued. We should avoid calling quota when it is not supported, so
check the quota flags.
Link: http://lkml.kernel.org/r/71604351584F6A4EBAE558C676F37CA401071AC9FB@H3CMLB12-EX.srv.huawei-3com.com Signed-off-by: guozhonghua <guozhonghua@h3c.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gang He [Fri, 2 Nov 2018 22:48:03 +0000 (15:48 -0700)]
ocfs2: remove ocfs2_is_o2cb_active()
Remove ocfs2_is_o2cb_active(). We have similar functions to identify
which cluster stack is being used via osb->osb_cluster_stack.
Secondly, the current implementation of ocfs2_is_o2cb_active() is not
totally safe. Based on the design of stackglue, we need to get
ocfs2_stack_lock before using ocfs2_stack related data structures, and
that active_stack pointer can be NULL in the case of mount failure.
Link: http://lkml.kernel.org/r/1495441079-11708-1-git-send-email-ghe@suse.com Signed-off-by: Gang He <ghe@suse.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Reviewed-by: Eric Ren <zren@suse.com> Acked-by: Changwei Ge <ge.changwei@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
THP allocation might be really disruptive when allocated on NUMA system
with the local node full or hard to reclaim. Stefan has posted an
allocation stall report on 4.12 based SLES kernel which suggests the
same issue:
The defrag mode is "madvise" and from the above report it is clear that
the THP has been allocated for MADV_HUGEPAGA vma.
Andrea has identified that the main source of the problem is
__GFP_THISNODE usage:
: The problem is that direct compaction combined with the NUMA
: __GFP_THISNODE logic in mempolicy.c is telling reclaim to swap very
: hard the local node, instead of failing the allocation if there's no
: THP available in the local node.
:
: Such logic was ok until __GFP_THISNODE was added to the THP allocation
: path even with MPOL_DEFAULT.
:
: The idea behind the __GFP_THISNODE addition, is that it is better to
: provide local memory in PAGE_SIZE units than to use remote NUMA THP
: backed memory. That largely depends on the remote latency though, on
: threadrippers for example the overhead is relatively low in my
: experience.
:
: The combination of __GFP_THISNODE and __GFP_DIRECT_RECLAIM results in
: extremely slow qemu startup with vfio, if the VM is larger than the
: size of one host NUMA node. This is because it will try very hard to
: unsuccessfully swapout get_user_pages pinned pages as result of the
: __GFP_THISNODE being set, instead of falling back to PAGE_SIZE
: allocations and instead of trying to allocate THP on other nodes (it
: would be even worse without vfio type1 GUP pins of course, except it'd
: be swapping heavily instead).
Fix this by removing __GFP_THISNODE for THP requests which are
requesting the direct reclaim. This effectivelly reverts 5265047ac301
on the grounds that the zone/node reclaim was known to be disruptive due
to premature reclaim when there was memory free. While it made sense at
the time for HPC workloads without NUMA awareness on rare machines, it
was ultimately harmful in the majority of cases. The existing behaviour
is similar, if not as widespare as it applies to a corner case but
crucially, it cannot be tuned around like zone_reclaim_mode can. The
default behaviour should always be to cause the least harm for the
common case.
If there are specialised use cases out there that want zone_reclaim_mode
in specific cases, then it can be built on top. Longterm we should
consider a memory policy which allows for the node reclaim like behavior
for the specific memory ranges which would allow a
: Both patches look correct to me but I'm responding to this one because
: it's the fix. The change makes sense and moves further away from the
: severe stalling behaviour we used to see with both THP and zone reclaim
: mode.
:
: I put together a basic experiment with usemem configured to reference a
: buffer multiple times that is 80% the size of main memory on a 2-socket
: box with symmetric node sizes and defrag set to "always". The defrag
: setting is not the default but it would be functionally similar to
: accessing a buffer with madvise(MADV_HUGEPAGE). Usemem is configured to
: reference the buffer multiple times and while it's not an interesting
: workload, it would be expected to complete reasonably quickly as it fits
: within memory. The results were;
:
: usemem
: vanilla noreclaim-v1
: Amean Elapsd-1 42.78 ( 0.00%) 26.87 ( 37.18%)
: Amean Elapsd-3 27.55 ( 0.00%) 7.44 ( 73.00%)
: Amean Elapsd-4 5.72 ( 0.00%) 5.69 ( 0.45%)
:
: This shows the elapsed time in seconds for 1 thread, 3 threads and 4
: threads referencing buffers 80% the size of memory. With the patches
: applied, it's 37.18% faster for the single thread and 73% faster with two
: threads. Note that 4 threads showing little difference does not indicate
: the problem is related to thread counts. It's simply the case that 4
: threads gets spread so their workload mostly fits in one node.
:
: The overall view from /proc/vmstats is more startling
:
: 4.19.0-rc1 4.19.0-rc1
: vanillanoreclaim-v1r1
: Minor Faults 35593425 708164
: Major Faults 484088 36
: Swap Ins 3772837 0
: Swap Outs 3932295 0
:
: Massive amounts of swap in/out without the patch
:
: Direct pages scanned 6013214 0
: Kswapd pages scanned 0 0
: Kswapd pages reclaimed 0 0
: Direct pages reclaimed 4033009 0
:
: Lots of reclaim activity without the patch
:
: Kswapd efficiency 100% 100%
: Kswapd velocity 0.000 0.000
: Direct efficiency 67% 100%
: Direct velocity 11191.956 0.000
:
: Mostly from direct reclaim context as you'd expect without the patch.
:
: Page writes by reclaim 3932314.000 0.000
: Page writes file 19 0
: Page writes anon 3932295 0
: Page reclaim immediate 42336 0
:
: Writes from reclaim context is never good but the patch eliminates it.
:
: We should never have default behaviour to thrash the system for such a
: basic workload. If zone reclaim mode behaviour is ever desired but on a
: single task instead of a global basis then the sensible option is to build
: a mempolicy that enforces that behaviour.
This was a severe regression compared to previous kernels that made
important workloads unusable and it starts when __GFP_THISNODE was
added to THP allocations under MADV_HUGEPAGE. It is not a significant
risk to go to the previous behavior before __GFP_THISNODE was added, it
worked like that for years.
This was simply an optimization to some lucky workloads that can fit in
a single node, but it ended up breaking the VM for others that can't
possibly fit in a single node, so going back is safe.
[mhocko@suse.com: rewrote the changelog based on the one from Andrea] Link: http://lkml.kernel.org/r/20180925120326.24392-2-mhocko@kernel.org Fixes: 5265047ac301 ("mm, thp: really limit transparent hugepage allocation to local node") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Debugged-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Tested-by: Mel Gorman <mgorman@techsingularity.net> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: <stable@vger.kernel.org> [4.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sam Protsenko [Fri, 2 Nov 2018 22:47:53 +0000 (15:47 -0700)]
include/linux/notifier.h: SRCU: fix ctags
ctags indexing ("make tags" command) throws this warning:
ctags: Warning: include/linux/notifier.h:125:
null expansion of name pattern "\1"
This is the result of DEFINE_PER_CPU() macro expansion. Fix that by
getting rid of line break.
Similar fix was already done in commit 25528213fe9f ("tags: Fix
DEFINE_PER_CPU expansions"), but this one probably wasn't noticed.
Link: http://lkml.kernel.org/r/20181030202808.28027-1-semen.protsenko@linaro.org Fixes: 9c80172b902d ("kernel/SRCU: provide a static initializer") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Fri, 2 Nov 2018 22:47:49 +0000 (15:47 -0700)]
mm: handle no memcg case in memcg_kmem_charge() properly
Mike Galbraith reported a regression caused by the commit 9b6f7e163cd0
("mm: rework memcg kernel stack accounting") on a system with
"cgroup_disable=memory" boot option: the system panics with the following
stack trace:
The problem occurs because get_mem_cgroup_from_current() returns the NULL
pointer if memory controller is disabled. Let's check if this is a case
at the beginning of memcg_kmem_charge() and just return 0 if
mem_cgroup_disabled() returns true. This is how we handle this case in
many other places in the memory controller code.
Link: http://lkml.kernel.org/r/20181029215123.17830-1-guro@fb.com Fixes: 9b6f7e163cd0 ("mm: rework memcg kernel stack accounting") Signed-off-by: Roman Gushchin <guro@fb.com> Reported-by: Mike Galbraith <efault@gmx.de> Acked-by: Rik van Riel <riel@surriel.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Shakeel Butt <shakeelb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netfilter: conntrack: fix calculation of next bucket number in early_drop
If there's no entry to drop in bucket that corresponds to the hash,
early_drop() should look for it in other buckets. But since it increments
hash instead of bucket number, it actually looks in the same bucket 8
times: hsize is 16k by default (14 bits) and hash is 32-bit value, so
reciprocal_scale(hash, hsize) returns the same value for hash..hash+7 in
most cases.
Fix it by increasing bucket number instead of hash and rename _hash
to bucket to avoid future confusion.
netfilter: nft_compat: ebtables 'nat' table is normal chain type
Unlike ip(6)tables, the ebtables nat table has no special properties.
This bug causes 'ebtables -A' to fail when using a target such as
'snat' (ebt_snat target sets ".table = "nat"'). Targets that have
no table restrictions work fine.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nfnetlink_cttimeout: pass default timeout policy to obj_to_nlattr
Otherwise, we hit a NULL pointer deference since handlers always assume
default timeout policy is passed.
netlink: 24 bytes leftover after parsing attributes in process `syz-executor2'.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 9575 Comm: syz-executor1 Not tainted 4.19.0+ #312
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:icmp_timeout_obj_to_nlattr+0x77/0x170 net/netfilter/nf_conntrack_proto_icmp.c:297
Fixes: c779e849608a ("netfilter: conntrack: remove get_timeout() indirection") Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jozsef Kadlecsik [Tue, 30 Oct 2018 21:43:42 +0000 (22:43 +0100)]
netfilter: ipset: Fix calling ip_set() macro at dumping
The ip_set() macro is called when either ip_set_ref_lock held only
or no lock/nfnl mutex is held at dumping. Take this into account
properly. Also, use Pablo's suggestion to use rcu_dereference_raw(),
the ref_netlink protects the set.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When IDLETIMER rule is added, sysfs file is created under
/sys/class/xt_idletimer/timers/
But some label name shouldn't be used.
".", "..", "power", "uevent", "subsystem", etc...
So that sysfs filename checking routine is needed.
====================
net: timeout fixes for GENET and SYSTEMPORT
This patch series fixes occasional transmit timeout around the time
the system goes into suspend. GENET and SYSTEMPORT have nearly the same
logic in that regard and were both affected in the same way.
Please queue up for stable, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce17 ("net: systemport: add suspend and resume support") Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Thu, 1 Nov 2018 22:55:37 +0000 (15:55 -0700)]
net: bcmgenet: protect stop from timeout
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log