Takashi Iwai [Thu, 21 Jun 2012 13:49:33 +0000 (15:49 +0200)]
ALSA: hda - Fix ALC272X codec detection
The codec ALC272X is a special codec for some Dell machines, and its
detection got broken in the recent kernel because SSID check (required
by ALC272X check) was moved to the later point. Now we need to move
this codec check to the right place, too.
Oleksij Rempel [Tue, 19 Jun 2012 20:21:19 +0000 (22:21 +0200)]
ALSA: snd_usb_audio: ignore ctrl errors on QuickCam Pro for Notebooks
This webcam works mostly ok, exept with skype.
Skype sends lots of ctrl messages to dynamically ajust
record level. If for some reasons it pokes some error
every thing goes broken:
- first pulseaudio blocks sound for all apps
- then video is reseted
- then skype freez
dmesg has lots of messages like:
cannot set freq 16000 to ep 0x86"
Dylan Reid [Sat, 16 Jun 2012 02:36:23 +0000 (19:36 -0700)]
ALSA: hda - Handle open while transitioning to D3.
This addresses an issue encountered when a pcm is opened while
transitioning to low power state (codec->power_on == 1 &&
codec->power_transition == -1). Add snd_pcm_power_up_d3wait to
hda_codec. This function is used to power up from azx_open as opposed
to snd_hda_power_up used from codec_exec_verb. When powering up from
azx_open, wait for pending power downs to complete, avoiding the power
up continuing in parallel with the power down on the work queue.
The specific issue seen was with the CS4210 codec, it powers off the ADC
and DAC nid in its suspend handler. If it is re-opened before the
~100ms power down process completes, the ADC and DAC nid are initialized
while powered down and audio is lost until another suspend/resume cycle.
Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.
Stephen Warren [Mon, 11 Jun 2012 17:27:19 +0000 (11:27 -0600)]
ASoC: tegra+wm8903: turn of mic detect when card is removed
If mic detect is left enabled and the WM8903 detects a status change,
the WM8903 driver will make a callback against the free()d jack, which
will cause a crash.
This problem can be triggered by fully initializing an audio card, then
removing and re-inserting the machine driver module.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 9 Jun 2012 03:27:17 +0000 (11:27 +0800)]
ASoC: wm8904: Fix cache only management
We should be using the regmap API consistently for all the cache only
configuration and we should be going cache only before we power down
the supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 9 Jun 2012 03:38:12 +0000 (11:38 +0800)]
ASoC: wm8904: Fix GPIO and MICBIAS initialisation for regmap conversion
We no longer have a flat ASoC cache so can't peer directly into the array
any more but should instead use the register I/O functions to update the
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org (v3.4)
Qiao Zhou [Mon, 4 Jun 2012 02:41:04 +0000 (10:41 +0800)]
ASoC: fix pxa-ssp compiling issue under mach-mmp
pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Sat, 9 Jun 2012 06:46:42 +0000 (08:46 +0200)]
vga_switcheroo: Enable/disable audio clients at the right time
The audio clients have to be disabled before disabling the VGA and
switching. Similarly, enabling the audio client should be done at
last. Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Steven Newbury [Fri, 8 Jun 2012 11:06:29 +0000 (13:06 +0200)]
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
When VGA_SWITCHEROO support is enabled hda_intel initialises the HDMI
audio device on the current VGA device. When it's not enabled it only
initialises the HDMI device on the default VGA adaptor, this means
secondary cards get no audio support which is very unhelpful for
multi-seat!
With this patch, when SUPPORT_VGA_SWITCHEROO is disabled hda_intel
initialises all HDMI audio devices, not just the default VGA.
[minor optimizations by tiwai]
Signed-off-by: Steven Newbury <steve@snewbury.org.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 7 Jun 2012 10:15:16 +0000 (12:15 +0200)]
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
When VGA-switcheroo is built in but unused on systems with multiple
graphics cards, the initializations of non-default graphics cards are
skipped and never enabled (because the switcheroo is activated only
when the controller supports). The current behavior is for avoiding
the system lockup by accessing the disabled GPU, but due to the recent
change in VGA-switcheroo, it determines the state simply by checking
with the default VGA device. This is the culprit.
Now with the new vga_switcheroo_get_client_state(), we can know the
initial state of the bound GPU, thus can determine the initial audio
client state more correctly.
Takashi Iwai [Thu, 7 Jun 2012 10:15:15 +0000 (12:15 +0200)]
vga_switcheroo: Add a helper function to get the client state
Add vga_switcheroo_get_client_state() to get the current state of the
client. This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 8 Jun 2012 07:01:37 +0000 (09:01 +0200)]
ALSA: usb-audio: Fix substream assignments
In 3.5 kernel, the endpoint is assigned dynamically for the
substreams, but the PCM assignment still checks the presence of the
endpoint pointer. This ended up in duplicated PCM substream creations
at probing time, resulting in kernel warnings like:
Mark Brown [Thu, 7 Jun 2012 22:53:48 +0000 (06:53 +0800)]
ASoC: wm2000: Always use a 4s timeout for the firmware
Rather than having varying timeouts depending on the transition always
use a 4s timeout. This provides better diagnostics for clocking errors
and ensures compatibility with current calibration firmwares.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 5 Jun 2012 11:31:32 +0000 (12:31 +0100)]
ASoC: wm8994: Apply volume updates with clocks enabled
Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.
There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Richard Zhao [Mon, 4 Jun 2012 01:42:54 +0000 (09:42 +0800)]
ASoC: imx-audmux: add pinctrl support
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Sun, 3 Jun 2012 00:39:40 +0000 (17:39 -0700)]
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
Joe Thornber [Sat, 2 Jun 2012 23:30:01 +0000 (00:30 +0100)]
dm thin: provide userspace access to pool metadata
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
Mike Snitzer [Sat, 2 Jun 2012 23:30:00 +0000 (00:30 +0100)]
dm thin: use slab mempools
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Sat, 2 Jun 2012 23:29:58 +0000 (00:29 +0100)]
dm mpath: allow ioctls to trigger pg init
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Christie [Sat, 2 Jun 2012 23:29:45 +0000 (00:29 +0100)]
dm mpath: delay retry of bypassed pg
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Sat, 2 Jun 2012 23:29:43 +0000 (00:29 +0100)]
dm mpath: reduce size of struct multipath
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
Linus Torvalds [Sat, 2 Jun 2012 23:17:03 +0000 (16:17 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
Linus Torvalds [Sat, 2 Jun 2012 22:21:43 +0000 (15:21 -0700)]
tty: Revert the tty locking series, it needs more work
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39be4 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d310886 - tty: add lockdep annotations 8f6576ad476b - tty: fix ldisc lock inversion trace d3ca8b64b97e - pty: Fix lock inversion b1d679afd766 - tty: drop the pty lock during hangup abcefe5fc357 - tty/amiserial: Add missing argument for tty_unlock() fd11b42e3598 - cris: fix missing tty arg in wait_event_interruptible_tty call d29f3ef39be4 - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Stephan Gatzka [Sat, 2 Jun 2012 03:04:06 +0000 (03:04 +0000)]
fec_mpc52xx: fix timestamp filtering
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Cc: stable <stable@vger.kernel.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Fri, 1 Jun 2012 10:29:08 +0000 (10:29 +0000)]
mcs7830: Implement link state detection
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 2 Jun 2012 16:03:54 +0000 (09:03 -0700)]
Merge 'for-linus' branches from git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs,signal}
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
Anton Blanchard [Sat, 2 Jun 2012 11:34:52 +0000 (21:34 +1000)]
powerpc: Fix size of st_nlink on 64bit
commit e57f93cc53b7 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Bruce Allan [Thu, 10 May 2012 02:51:17 +0000 (02:51 +0000)]
e1000e: fix Rapid Start Technology support for i217
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Sat, 2 Jun 2012 02:56:23 +0000 (19:56 -0700)]
Merge branch 'akpm' (Fixups for Andrew's patchbomb)
Merge fixups for the mac NLS tables from Andrew.
* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments
Linus Torvalds [Sat, 2 Jun 2012 02:51:22 +0000 (19:51 -0700)]
nls: fix (and rename) mac NLS table files and config options
The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).
And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".
So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Linus Torvalds [Fri, 1 Jun 2012 23:57:51 +0000 (16:57 -0700)]
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
Linus Torvalds [Fri, 1 Jun 2012 23:55:42 +0000 (16:55 -0700)]
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Linus Torvalds [Fri, 1 Jun 2012 23:51:37 +0000 (16:51 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Some significant improvements for the Sony driver on newer machines,
but other than that mostly just minor fixes and a patch to remove the
broken rfkill code from the Dell driver."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits)
apple-gmux: Fix up the suspend/resume patch
dell-laptop: Remove rfkill code
toshiba_acpi: Fix mis-merge
dell-laptop: Add touchpad led support for Dell V3450
acer-wmi: add 3 laptops to video backlight vendor mode quirk table
sony-laptop: add touchpad enable/disable function
sony-laptop: add missing Fn key combos for 0x100 handlers
sony-laptop: add support for more WWAN modems
sony-laptop: new keyboard backlight handle
sony-laptop: add high speed battery charging function
sony-laptop: support automatic resume on lid open
sony-laptop: adjust error handling in finding SNC handles
sony-laptop: add thermal profiles support
sony-laptop: support battery care functions
sony-laptop: additional debug statements
sony-laptop: improve SNC initialization and acpi notify callback code
sony-laptop: use kstrtoul to parse sysfs values
sony-laptop: generalise ACPI calls into SNC functions
sony-laptop: fix return path when no ACPI buffer is allocated
sony-laptop: use soft rfkill status stored in hw
...
Linus Torvalds [Fri, 1 Jun 2012 23:50:23 +0000 (16:50 -0700)]
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull slab updates from Pekka Enberg:
"Mainly a bunch of SLUB fixes from Joonsoo Kim"
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slub: use __SetPageSlab function to set PG_slab flag
slub: fix a memory leak in get_partial_node()
slub: remove unused argument of init_kmem_cache_node()
slub: fix a possible memory leak
Documentations: Fix slabinfo.c directory in vm/slub.txt
slub: fix incorrect return type of get_any_partial()
Linus Torvalds [Fri, 1 Jun 2012 22:46:46 +0000 (15:46 -0700)]
Merge branch 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm fixes for ux500 mismerge mishap from Arnd Bergmann:
"The device tree conversion for arm/ux500 in 3.5 turns out to be
incomplete because of a mismerge done by Linus Walleij that I failed
to notice early enough and that Lee Jones as the original author of
those patches did not manage to fix during the -next cycle. While we
originally to get a much larger set of ux500 device tree enablement
patches merged, this did not happen in time.
After some discussion at Linaro Connect conference this week, Lee has
been able to do damage control and provide a series to put the broken
platform back into usable shape for both DT and non-DT based booting.
This series has not been part of linux-next and is based on top of the
current state of the upstream kernel rather than an -rc, but this is
the best we could manage given the earlier breakage."
* 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Enable probing of pinctrl through Device Tree
ARM: ux500: Add support for ab8500 regulators into the Device Tree
ARM: ux500: Provide regulator support for SMSC911x via Device Tree
ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot
ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree
ARM: ux500: Only initialise STE's UIBs on boards which support them
ARM: ux500: Disable platform setup of the ab8500 when DT is enabled
ARM: ux500: Use correct format for dynamic IRQ assignment
ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots
ARM: ux500: PRCMU related configuration and layout corrections for Device Tree
ARM: ux500: Remove DB8500 PRCMU platform registration when DT is enabled
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: New DT:ed u8500_init_devices for one-by-one device enablement
ARM: ux500: New DT:ed snowball_platform_devs for one-by-one device enablement
pinctrl-nomadik: Allow Device Tree driver probing
Devendra Naga [Thu, 31 May 2012 01:51:20 +0000 (01:51 +0000)]
r8169: call netif_napi_del at errpaths and at driver unload
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Jun 2012 22:40:29 +0000 (15:40 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes:
- vmware memory corruption
- ttm spinlock balance
- cirrus/mgag200 work in the presence of efifb
and finally Alex and Jerome managed to track down a magic set of bits
that on certain rv740 and evergreen cards allow the correct use of the
complete set of render backends, this makes the cards operate
correctly in a number of scenarios we had issues in before, it also
manages to boost speed on benchmarks my large amounts on these
specific gpus."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/edid: Make the header fixup threshold tunable
drm/radeon: fix regression in UMS CS ioctl
drm/vmwgfx: Fix nasty write past alloced memory area
drm/ttm: Fix spinlock imbalance
drm/radeon: fixup tiling group size and backendmap on r6xx-r9xx (v4)
drm/radeon: fix HD6790, HD6570 backend programming
drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
drm/radeon: fix bank information in tiling config
drm/mgag200: kick off conflicting framebuffers earlier.
drm/cirrus: kick out conflicting framebuffers earlier
cirrus: avoid crash if driver fails to load
Linus Torvalds [Fri, 1 Jun 2012 22:39:26 +0000 (15:39 -0700)]
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial driver-specific fixes."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdspm - Work around broken DDS value on PCI RME MADI
ALSA: usb-audio: fix rate_list memory leak
ASoC: fsi: bugfix: ensure dma is terminated
ASoC: fsi: bugfix: correct dma area
ASoC: fsi: bugfix: enable master clock control on DMA stream
ASoC: imx-ssi: Use clk_prepare_enable/clk_disable_unprepare
H.J. Lu [Tue, 22 May 2012 03:29:45 +0000 (20:29 -0700)]
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
When I added x32 ptrace to 3.4 kernel, I also include PTRACE_ARCH_PRCTL
support for x32 GDB For ARCH_GET_FS/GS, it takes a pointer to int64. But
at user level, ARCH_GET_FS/GS takes a pointer to int32. So I have to add
x32 ptrace to glibc to handle it with a temporary int64 passed to kernel and
copy it back to GDB as int32. Roland suggested that PTRACE_ARCH_PRCTL
is obsolete and x32 GDB should use fs_base and gs_base fields of
user_regs_struct instead.
Accordingly, remove PTRACE_ARCH_PRCTL completely from the x32 code to
avoid possible memory overrun when pointer to int32 is passed to
kernel.
Gabor Juhos [Wed, 23 May 2012 22:17:23 +0000 (00:17 +0200)]
mtd: block2mtd: fix recursive call of mtd_writev
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
Matthew Garrett [Fri, 1 Jun 2012 19:18:52 +0000 (15:18 -0400)]
apple-gmux: Fix up the suspend/resume patch
I incorporated the wrong version of the suspend/resume patch for gmux,
and so lost David Woodhouse's fix to leave the backlight level unchanged
over suspend/resume. This fixes it up to v2.
Frank Svendsboe [Thu, 17 May 2012 20:43:09 +0000 (22:43 +0200)]
mtd: of_parts: fix breakage in Kconfig
MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit d6137badeff1ef64b4e0092ec249ebdeaeb3ff37. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.
Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com> Cc: stable@kernel.org [3.2+] Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds [Fri, 1 Jun 2012 18:53:44 +0000 (11:53 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
Eric Dumazet [Fri, 1 Jun 2012 01:47:50 +0000 (01:47 +0000)]
tcp: reflect SYN queue_mapping into SYNACK packets
While testing how linux behaves on SYNFLOOD attack on multiqueue device
(ixgbe), I found that SYNACK messages were dropped at Qdisc level
because we send them all on a single queue.
Obvious choice is to reflect incoming SYN packet @queue_mapping to
SYNACK packet.
Under stress, my machine could only send 25.000 SYNACK per second (for
200.000 incoming SYN per second). NIC : ixgbe with 16 rx/tx queues.
After patch, not a single SYNACK is dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Hans Schillstrom <hans.schillstrom@ericsson.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Hans Schillstrom <hans.schillstrom@ericsson.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 31 May 2012 18:19:48 +0000 (18:19 +0000)]
8139cp/8139too: terminate the eeprom access with the right opmode
Currently, we terminate the eeprom access through clearing the CS by:
RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);
This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 31 May 2012 18:19:39 +0000 (18:19 +0000)]
8139cp: set ring address before enabling receiver
Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.
btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 1 Jun 2012 05:54:56 +0000 (05:54 +0000)]
cipso: handle CIPSO options correctly when NetLabel is disabled
When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero). In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.
This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code. The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.
The behavior when NetLabel is enabled is unchanged.
Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Jun 2012 17:34:35 +0000 (10:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Linus Torvalds [Fri, 1 Jun 2012 17:12:15 +0000 (10:12 -0700)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull Ext4 updates from Theodore Ts'o:
"The major new feature added in this update is Darrick J Wong's
metadata checksum feature, which adds crc32 checksums to ext4's
metadata fields.
There is also the usual set of cleanups and bug fixes."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (44 commits)
ext4: hole-punch use truncate_pagecache_range
jbd2: use kmem_cache_zalloc wrapper instead of flag
ext4: remove mb_groups before tearing down the buddy_cache
ext4: add ext4_mb_unload_buddy in the error path
ext4: don't trash state flags in EXT4_IOC_SETFLAGS
ext4: let getattr report the right blocks in delalloc+bigalloc
ext4: add missing save_error_info() to ext4_error()
ext4: add debugging trigger for ext4_error()
ext4: protect group inode free counting with group lock
ext4: use consistent ssize_t type in ext4_file_write()
ext4: fix format flag in ext4_ext_binsearch_idx()
ext4: cleanup in ext4_discard_allocated_blocks()
ext4: return ENOMEM when mounts fail due to lack of memory
ext4: remove redundundant "(char *) bh->b_data" casts
ext4: disallow hard-linked directory in ext4_lookup
ext4: fix potential integer overflow in alloc_flex_gd()
ext4: remove needs_recovery in ext4_mb_init()
ext4: force ro mount if ext4_setup_super() fails
ext4: fix potential NULL dereference in ext4_free_inodes_counts()
ext4/jbd2: add metadata checksumming to the list of supported features
...
Al Viro [Mon, 30 Apr 2012 22:24:46 +0000 (18:24 -0400)]
x86: get rid of calling do_notify_resume() when returning to kernel mode
If we end up calling do_notify_resume() with !user_mode(refs), it
does nothing (do_signal() explicitly bails out and we can't get there
with TIF_NOTIFY_RESUME in such situations). Then we jump to
resume_userspace_sig, which rechecks the same thing and bails out
to resume_kernel, thus breaking the loop.
It's easier and cheaper to check *before* calling do_notify_resume()
and bail out to resume_kernel immediately. And kill the check in
do_signal()...
Note that on amd64 we can't get there with !user_mode() at all - asm
glue takes care of that.
Acked-and-reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Tue, 1 May 2012 18:44:14 +0000 (19:44 +0100)]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
Move the test for kernel mode processing from do_signal() into entry.S to also
prevent system call exit tracing and userspace resumption notification handling
happening when returning from kernel exceptions.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 28 Apr 2012 06:04:15 +0000 (02:04 -0400)]
new helper: signal_delivered()
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Al Viro [Fri, 27 Apr 2012 17:58:59 +0000 (13:58 -0400)]
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Al Viro [Tue, 22 May 2012 03:33:55 +0000 (23:33 -0400)]
new helper: restore_saved_sigmask()
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Al Viro [Thu, 26 Apr 2012 22:31:00 +0000 (18:31 -0400)]
HAVE_RESTORE_SIGMASK is defined on all architectures now
Everyone either defines it in arch thread_info.h or has TIF_RESTORE_SIGMASK
and picks default set_restore_sigmask() in linux/thread_info.h. Kill the
ifdefs, slap #error in linux/thread_info.h to catch breakage when new ones
get merged.
Matthew Garrett [Fri, 1 Jun 2012 16:46:56 +0000 (12:46 -0400)]
dell-laptop: Remove rfkill code
The interface just doesn't work on some machines, and Dell haven't been
able to tell us either which machines those are or what we should be
doing instead. This would be fine, except it results in userspace ending
up confused and general sadness. So let's just rip it out for now.
Miklos Szeredi [Mon, 21 May 2012 15:30:20 +0000 (17:30 +0200)]
nfs: don't open in ->d_revalidate
NFSv4 can't do reliable opens in d_revalidate, since it cannot know whether a
mount needs to be followed or not. It does check d_mountpoint() on the dentry,
which can result in a weird error if the VFS found that the mount does not in
fact need to be followed, e.g.:
# mount --bind /mnt/nfs /mnt/nfs-clone
# echo something > /mnt/nfs/tmp/bar
# echo x > /tmp/file
# mount --bind /tmp/file /mnt/nfs-clone/tmp/bar
# cat /mnt/nfs/tmp/bar
cat: /mnt/nfs/tmp/bar: Not a directory
Which should, by any sane filesystem, result in "something" being printed.
So instead do the open in f_op->open() and in the unlikely case that the cached
dentry turned out to be invalid, drop the dentry and return EOPENSTALE to let
the VFS retry.
Miklos Szeredi [Mon, 21 May 2012 15:30:19 +0000 (17:30 +0200)]
vfs: retry last component if opening stale dentry
NFS optimizes away d_revalidates for last component of open. This means that
open itself can find the dentry stale.
This patch allows the filesystem to return EOPENSTALE and the VFS will retry the
lookup on just the last component if possible.
If the lookup was done using RCU mode, including the last component, then this
is not possible since the parent dentry is lost. In this case fall back to
non-RCU lookup. Currently this is not used since NFS will always leave RCU
mode.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
projects / mirror_ubuntu-kernels.git / log