Francisco Jerez [Wed, 16 Dec 2009 11:27:11 +0000 (12:27 +0100)]
drm/i2c/ch7006: Drop build time dependency to nouveau.
This partially reverts e4b41066, as this driver is intended to be
useful with any KMS driver for suitable hardware. The missing build
dependency that commit workarounded was DRM_KMS_HELPER.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Francisco Jerez [Fri, 11 Dec 2009 15:51:09 +0000 (16:51 +0100)]
drm/nouveau: Make the MM aware of pre-G80 tiling.
This commit has also the following 3 bugfix commits squashed into it from
the nouveau git tree:
drm/nouveau: Fix up the tiling alignment restrictions for nv1x.
drm/nouveau: Fix up the nv2x tiling alignment restrictions.
drm/nv50: fix align typo for g9x
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
David John [Thu, 31 Dec 2009 06:30:46 +0000 (12:00 +0530)]
drm: Keep disabled outputs disabled after suspend / resume
With the current DRM code, an output that has been powered off
from userspace will automatically power back on when resuming
from suspend. This patch fixes this behaviour.
Tested only with the Intel i915 driver on an Intel GM45 Express
chipset.
Signed-off-by: David John <davidjon@xenontk.org> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 7 Jan 2010 04:00:29 +0000 (14:00 +1000)]
Merge remote branch 'korg/drm-radeon-next' into drm-linus
* korg/drm-radeon-next:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
Zhenyu Wang [Tue, 5 Jan 2010 03:25:05 +0000 (11:25 +0800)]
drm: remove address mask param for drm_pci_alloc()
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 23 Dec 2009 01:18:33 +0000 (11:18 +1000)]
Merge remote branch 'korg/drm-radeon-next' into drm-linus
* korg/drm-radeon-next:
drm/radeon/kms: add definitions for v4 power tables
drm/radeon/kms: never combine LVDS with another encoder
drm/radeon/kms: Check module arguments to be valid V2
drm/radeon/kms: Avoid crash when trying to cleanup uninitialized structure
drm/radeon/kms: add cvt mode if we only have lvds w/h and no edid (v4)
drm/radeon/kms: add 3DC compression support
drm/radeon/kms: allow rendering while no colorbuffer is set on r300
drm/radeon/kms: enable memory clock reading on legacy (V2)
drm/radeon/kms: prevent parallel AtomBIOS calls
drm/radeon/kms: set proper default tv standard
drm/radeon/kms: fix legacy rmx
drm/radeon/kms/atom: fill in proper defines for digital setup
Alex Deucher [Sat, 19 Dec 2009 17:45:12 +0000 (12:45 -0500)]
drm/radeon/kms: add definitions for v4 power tables
[airlied: just adding this for completeness to avoid drift between
public atombios.h files] Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Fri, 11 Dec 2009 19:36:19 +0000 (20:36 +0100)]
drm/radeon/kms: Avoid crash when trying to cleanup uninitialized structure
Add boolean to record if some part of the driver are initialized or
not this allow to avoid a crash when trying to cleanup uninitialized
structure members.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 22 Dec 2009 15:06:49 +0000 (10:06 -0500)]
drm/radeon/kms: add cvt mode if we only have lvds w/h and no edid (v4)
This fixes LVDS on some mac laptops without a panel edid.
v2 - Set proper mode type flags
v3 - Note that this is not neceesarily the exact panel mode,
but an approximation based on the cvt formula. For these
systems we should ideally read the mode info out of the
registers or add a mode table, but this works and is much
simpler.
v4 - Update comments and debug message.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Marek Olšák [Thu, 17 Dec 2009 05:02:28 +0000 (06:02 +0100)]
drm/radeon/kms: allow rendering while no colorbuffer is set on r300
Because hardware cannot disable all colorbuffers directly to do depth-only
rendering, a user should:
- disable reading from a colorbuffer in blending
- disable fastfill
- set the color channel mask to 0 to prevent writing to a colorbuffer
Dave Airlie [Wed, 23 Dec 2009 00:28:24 +0000 (10:28 +1000)]
Merge remote branch 'nouveau/for-airlied' into drm-linus
* nouveau/for-airlied:
drm/nouveau: fix bug causing pinned buffers to lose their NO_EVICT flag
drm/nv50: fix suspend/resume delays without firmware present
drm/nouveau: prevent all channel creation if accel not available
drm/nv50: fix two potential suspend/resume oopses
drm/nv40: implement ctxprog/state generation
drm/nv10: Add the initial graph context and soft methods needed for LMA.
drm/nouveau: Fix up buffer eviction, and evict them to GART, if possible.
drm/nouveau: Add proper error handling to nouveau_card_init
drm/nv04: Fix NV04 set_operation software method.
drm/nouveau: Kill global state in BIOS script interpreter
drm/nouveau: Kill global state in NvShadowBIOS
drm/nouveau: use drm debug levels
drm/i2c/ch7006: Fix load detection false positives right after system init.
drm/nv04-nv40: Fix "conflicting memory types" when saving/restoring VGA fonts.
drm/vmwgfx: Return -ERESTARTSYS when interrupted by a signal.
Fixes for TTM API change.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/vmwgfx: Fix unlocked ioctl and add proper access control
This fixes up vmwgfx for the unlocked ioctl code to avoid
doing it in the driver. Also adds ioctl flags.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Andi Kleen [Mon, 21 Dec 2009 01:24:47 +0000 (02:24 +0100)]
DRM: Rename clamp variable
linux/kernel.h has a "clamp" macro, but r300_cmdbuf also uses a variable
with the same name. Right now it doesn't seem to include the header,
but sooner or later someone will. So better rename the variable
now.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Arnd Bergmann [Wed, 16 Dec 2009 22:17:09 +0000 (22:17 +0000)]
drm: convert drm_ioctl to unlocked_ioctl
drm_ioctl is called with the Big Kernel Lock held,
which shows up very high in statistics on vfs_ioctl.
Moving the lock into the drm_ioctl function itself
makes sure we blame the right subsystem and it gets
us one step closer to eliminating the locked version
of fops->ioctl.
Since drm_ioctl does not require the lock itself,
we only need to hold it while calling the specific
handler. The 32 bit conversion handlers do not
interact with any other code, so they don't need
the BKL here either and can just call drm_ioctl.
As a bonus, this cleans up all the other users
of drm_ioctl which now no longer have to find
the inode or call lock_kernel.
[airlied: squashed the non-driver bits
of the second patch in here, this provides
the flag for drivers to use to select unlocked
ioctls - but doesn't modify any drivers].
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.sourceforge.net Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Wed, 16 Dec 2009 04:28:55 +0000 (14:28 +1000)]
drm/nouveau: prevent all channel creation if accel not available
Previously, if there was no firmware available, the DRM would just
disable channel creation from userspace, but still use a single
channel for its own purposes.
With a bit of care it should actually be possible to do this, due
to the DRM's very limited use of the engine. It currently doesn't
work correctly however, resulting in corrupted fbcon and hangs on
a number of cards.
Ben Skeggs [Tue, 15 Dec 2009 12:02:47 +0000 (22:02 +1000)]
drm/nv40: implement ctxprog/state generation
The context programs are *very* simple compared to the ones used by
the binary driver. There's notes in nv40_grctx.c explaining most of
the things we don't implement. If we discover if/why any of it is
required further down the track, we'll handle it then.
The PGRAPH state generated for each chipset should match what NVIDIA
do almost exactly (there's a couple of exceptions). If someone has
a lot of time on their hands, they could figure out the mapping of
object/method to PGRAPH register and demagic the initial state a little,
it's not terribly important however.
At time of commit, confirmed to be working at least well enough for
accelerated X (and where tested, for 3D apps) on NV40, NV43, NV44, NV46,
NV49, NV4A, NV4B and NV4E.
A module option has been added to force the use of external firmware
blobs if it becomes required.
Maarten Maathuis [Sun, 13 Dec 2009 15:53:12 +0000 (16:53 +0100)]
drm/nouveau: use drm debug levels
- Use driver level (0x2) for NV_DEBUG instead of all levels
- Create a NV_DEBUG_KMS for KMS level (0x4) and use them in modesetting code
- Remove a few odd NV_TRACE calls and replace some of them with NV_DEBUG_KMS or
NV_INFO
Signed-off-by: Maarten Maathuis <madman2003@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Wed, 16 Dec 2009 05:52:21 +0000 (15:52 +1000)]
Merge remote branch 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next into drm-linus
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: remove use of -ERESTART
nouveau: Fix endianness with new context program loader
drm/nouveau: fix build with CONFIG_AGP=n
drm/nouveau: fix ch7006 build
Jerome Glisse [Tue, 15 Dec 2009 17:23:23 +0000 (18:23 +0100)]
drm/radeon/kms: Return to userspace on ERESTARTSYS
radeon_object.h wasn't converted to ERESTARTSYS change. No
each time we got an ERESTARTSYS we return to userspace (ie
we were interrupted by a signal and we let the userspace
reschedule the ioctl).
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Fri, 11 Dec 2009 14:13:22 +0000 (15:13 +0100)]
drm/radeon/kms: If no placement is supplied fallback to system
Do as we did before rework, if no placement is supplied at bo
creation time, fallback to allocating bo from system ram. This
will fix most of the creation failed issue report we got since
the rework get merged.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Thu, 10 Dec 2009 17:07:26 +0000 (18:07 +0100)]
drm/ttm: Fix memory type manager debug information printing
System memory type doesn't have a drm_mm manager associated to
it. This patch avoid trying to call drm_mm_debug on unitialized
drm_mm when printing debug info on the system memory manager.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
1) The function was previously called with a potentially empty
LRU list which would have lead to an OOPS or servere corruption.
2) In rare cases, after reservation has succeeded, another process may
already have evicted it or even pinned it. We must revalidate the
buffer status after releasing the lru lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
1) Remove from lru before reserving so we avoid competing with
evicting processes.
2) Avoid calling kref_put() on bo::list_kref while spinlocked.
3) Additional refcounting bug-checking.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 14 Dec 2009 04:51:35 +0000 (14:51 +1000)]
drm/ttm: fix two bugs in new placement routines.
a) the loops were going to <= not <, leading to illegal memory access
b) the busy placement checks were using the placement arrays not the
busy placement ones.
Acked-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
nouveau: Fix endianness with new context program loader
When switching to request_firmware() to load the context programs,
some endian fixes need to be applied. This makes it work again on
my quad g5 nvidia 6600.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit adds the vmwgfx driver for the VWware Virtual GPU aka SVGA.
The driver is under staging the same as Nouveau and Radeon KMS. Hopefully
the 2D ioctls are bug free and don't need changing, so that part of the
API should be stable. But there there is a pretty big chance that the 3D API
will change in the future.
Signed-off-by: Thomas Hellström <thellstrom@vmware.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
These headers are shared between multiple place where
different coding standards apply. They will be fixed
up at a later time.
Signed-off-by: Thomas Hellström <thellstrom@vmware.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Fri, 11 Dec 2009 09:24:15 +0000 (19:24 +1000)]
drm/nouveau: Add DRM driver for NVIDIA GPUs
This adds a drm/kms staging non-API stable driver for GPUs from NVIDIA.
This driver is a KMS-based driver and requires a compatible nouveau
userspace libdrm and nouveau X.org driver.
This driver requires firmware files not available in this kernel tree,
interested parties can find them via the nouveau project git archive.
This driver is reverse engineered, and is in no way supported by nVidia.
Support for nearly the complete range of nvidia hw from nv04->g80 (nv50)
is available, and the kms driver should support driving nearly all
output types (displayport is under development still) along with supporting
suspend/resume.
This work is all from the upstream nouveau project found at
nouveau.freedesktop.org.
The original authors list from nouveau git tree is:
Anssi Hannula <anssi.hannula@iki.fi>
Ben Skeggs <bskeggs@redhat.com>
Francisco Jerez <currojerez@riseup.net>
Maarten Maathuis <madman2003@gmail.com>
Marcin Kościelnicki <koriakin@0x04.net>
Matthew Garrett <mjg@redhat.com>
Matt Parnell <mparnell@gmail.com>
Patrice Mandin <patmandin@gmail.com>
Pekka Paalanen <pq@iki.fi>
Xavier Chantry <shiningxc@gmail.com>
along with project founder Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Thu, 10 Dec 2009 16:16:27 +0000 (17:16 +0100)]
drm/ttm: Convert ttm_buffer_object_init to use ttm_placement
Convert ttm_buffer_object_init to use struct ttm_placement and
rename to ttm_bo_init for consistency with function naming. This
allow to give more complex placement at buffer creation. For
instance you ask to allocate bo into vram first but if there is
not enough vram you can give system as a second possible
placement. It also allow to create buffer in a specific range.
Also rename ttm_buffer_object_validate to ttm_bo_validate.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>