David S. Miller [Mon, 13 Feb 2017 14:30:22 +0000 (09:30 -0500)]
Merge branch 'mv88e6xxx-Watchdog-support'
Andrew Lunn says:
====================
mv88e6xxx Watchdog support
The Marvell switches have an in built watchdog over some of the
internal state machine. The watchdog can be configured to raise an
interrupt on error. The problem the watchdog found is then logged to
the kernel log.
The older switches can automagically perform a software reset when the
watchdog triggers. This just resets the internal state machine, but
leaves the switch configuration unchanged.
The 6390 family of switches cannot both raise an interrupt and
automagically perform a software reset. So the interrupt handler has
to perform the switch reset, and then re-enable the watchdog
interrupts.
This has been tested using hacked together debugfs code which allows
the "force" bit to be set, so cause a watchdog interrupt.
v2: Remove g2_prefix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.
The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Feb 2017 03:18:52 +0000 (22:18 -0500)]
Merge branch 'bnxt_en-misc-updates'
Michael Chan says:
====================
bnxt_en: Misc updates.
Miscellaneous updates include update of the firmware spec, ethtool flash
enhancement, ethtool -l minor fix, NTUPLE support enhancements, FEC
link settings message during link up, and new PCI IDs. Please review.
Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepak Khungar [Mon, 13 Feb 2017 00:18:18 +0000 (19:18 -0500)]
bnxt_en: Added PCI IDs for BCM57452 and BCM57454 ASICs
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 13 Feb 2017 00:18:15 +0000 (19:18 -0500)]
bnxt_en: Do not setup PHY unless driving a single PF.
If it is a VF or an NPAR function, the firmware call to setup the PHY
will fail. Adding this check will prevent unnecessary firmware calls
to setup the PHY unless calling from the PF. This will also eliminate
many unnecessary warning messages when the call from a VF or NPAR fails.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 13 Feb 2017 00:18:13 +0000 (19:18 -0500)]
bnxt_en: Allow NETIF_F_NTUPLE to be enabled on VFs.
Commit ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.") has added
code to allow NTUPLE to be enabled on VFs. So we now remove the
BNXT_VF() check in rfs_capable() to allow NTUPLE on VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 13 Feb 2017 00:18:12 +0000 (19:18 -0500)]
bnxt_en: Fix ethtool -l pre-set max combined channel.
With commit d1e7925e6d80 ("bnxt_en: Centralize logic to reserve rings."),
ring allocation for combined rings has become stricter. A combined
ring must now have an rx-tx ring pair. The pre-set max. for combined
rings should now be min(rx, tx).
Fixes: d1e7925e6d80 ("bnxt_en: Centralize logic to reserve rings.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kshitij Soni [Mon, 13 Feb 2017 00:18:11 +0000 (19:18 -0500)]
bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag.
If the HWRM_NVM_INSTALL_UPDATE command fails with the error code
NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR, retry the command with
a new flag to allow defragmentation. Since we are checking the
response for error code, we also need to take the mutex until
we finish reading the response.
Signed-off-by: Kshitij Soni <kshitij.soni@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, most relevantly they are:
1) Extend nft_exthdr to allow to match TCP options bitfields, from
Manuel Messner.
2) Allow to check if IPv6 extension header is present in nf_tables,
from Phil Sutter.
3) Allow to set and match conntrack zone in nf_tables, patches from
Florian Westphal.
4) Several patches for the nf_tables set infrastructure, this includes
cleanup and preparatory patches to add the new bitmap set type.
5) Add optional ruleset generation ID check to nf_tables and allow to
delete rules that got no public handle yet via NFTA_RULE_ID. These
patches add the missing kernel infrastructure to support rule
deletion by description from userspace.
6) Missing NFT_SET_OBJECT flag to select the right backend when sets
stores an object map.
7) A couple of cleanups for the expectation and SIP helper, from Gao
feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This new attribute allows us to uniquely identify a rule in transaction.
Robots may trigger an insertion followed by deletion in a batch, in that
scenario we still don't have a public rule handle that we can use to
delete the rule. This is similar to the NFTA_SET_ID attribute that
allows us to refer to an anonymous set from a batch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: add check_genid to the nfnetlink subsystem
This patch implements the check generation id as provided by nfnetlink.
This allows us to reject ruleset updates against stale baseline, so
userspace can retry update with a fresh ruleset cache.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nfnetlink: allow to check for generation ID
This patch allows userspace to specify the generation ID that has been
used to build an incremental batch update.
If userspace specifies the generation ID in the batch message as
attribute, then nfnetlink compares it to the current generation ID so
you make sure that you work against the right baseline. Otherwise, bail
out with ERESTART so userspace knows that its changeset is stale and
needs to respin. Userspace can do this transparently at the cost of
taking slightly more time to refresh caches and rework the changeset.
This check is optional, if there is no NFNL_BATCH_GENID attribute in the
batch begin message, then no check is performed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ivan Khoronzhuk [Sat, 11 Feb 2017 01:49:57 +0000 (03:49 +0200)]
net: ethernet: ti: cpsw: return NET_XMIT_DROP if skb_padto failed
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sat, 11 Feb 2017 05:38:36 +0000 (21:38 -0800)]
vxlan: remove vni zero check and drop for COLLECT_METADATA
This patch drops the vni zero check for COLLECT_METADATA mode.
It is not really needed, vni zero is a valid vni.
Fixes: 3ad7a4b141eb ("vxlan: support fdb and learning in COLLECT_METADATA mode" Reported-by: Joe Stringer <joe@ovn.org> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Sat, 11 Feb 2017 11:49:20 +0000 (13:49 +0200)]
net: rename dst_neigh_output back to neigh_output
After the dst->pending_confirm flag was removed, we do not
need anymore to provide dst arg to dst_neigh_output.
So, rename it to neigh_output as before commit 5110effee8fd
("net: Do delayed neigh confirmation.").
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 10 Feb 2017 17:34:59 +0000 (17:34 +0000)]
sfc: fix swapped arguments to efx_ef10_handle_rx_event_errors
Fixes: a0ee35414837 ("sfc: process RX event inner checksum flags") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 12 Feb 2017 01:59:43 +0000 (20:59 -0500)]
Merge branch 'ipvtap'
Sainath Grandhi says:
====================
Refactor macvtap to re-use tap functionality by other virtual intefaces
Tap character devices can be implemented on other virtual interfaces like
ipvlan, similar to macvtap. Source code for tap functionality in macvtap
can be re-used for this purpose.
This patch series splits macvtap source into two modules, macvtap and tap.
This patch series also includes a patch for implementing tap character
device driver based on the IP-VLAN network interface, called ipvtap.
These patches are tested on x86 platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sainath Grandhi [Sat, 11 Feb 2017 00:03:52 +0000 (16:03 -0800)]
ipvtap: IP-VLAN based tap driver
This patch adds a tap character device driver that is based on the
IP-VLAN network interface, called ipvtap. An ipvtap device can be created
in the same way as an ipvlan device, using 'type ipvtap', and then accessed
using the tap user space interface.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sainath Grandhi [Sat, 11 Feb 2017 00:03:49 +0000 (16:03 -0800)]
tap: Abstract type of virtual interface from tap implementation
macvlan object is re-structured to hold tap related elements in a separate
entity, tap_dev. Upon NETDEV_REGISTER device_event, tap_dev is registered with
idr and fetched again on tap_open. Few of the tap functions are modified to
accepted tap_dev as argument. tap_dev object includes callbacks to be used by
underlying virtual interface to take care of tx and rx accounting.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sainath Grandhi [Sat, 11 Feb 2017 00:03:46 +0000 (16:03 -0800)]
tap: Refactoring macvtap.c
macvtap module has code for tap/queue management and link management. This patch splits
the code into macvtap_main.c for link management and tap.c for tap/queue management.
Functionality in tap.c can be re-used for implementing tap on other virtual interfaces.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
Linus Torvalds [Fri, 10 Feb 2017 22:29:30 +0000 (14:29 -0800)]
Merge tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are some last-minute fixes: two fixes for races in ALSA sequencer
queue spotted by syzkaller, a revert for a regression of LINE6 driver
(since 4.9), and a trivial new codec ID addition for Nvidia HDMI"
* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
ALSA: seq: Fix race at creating a queue
Revert "ALSA: line6: Only determine control port properties if needed"
ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()
Linus Torvalds [Fri, 10 Feb 2017 22:23:45 +0000 (14:23 -0800)]
Merge tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux
Pull nfsd revert from Bruce Fields:
"This patch turned out to have a couple problems. The problems are
fixable, but at least one of the fixes is a little ugly. The original
bug has always been there, so we can wait another week or two to get
this right"
* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
nfsd: Revert "nfsd: special case truncates some more"
Linus Torvalds [Fri, 10 Feb 2017 22:10:35 +0000 (14:10 -0800)]
Merge tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes friom Michael Ellerman:
"Apologies for the late pull request, but Ben has been busy finding bugs.
- Userspace was semi-randomly segfaulting on radix due to us
incorrectly handling a fault triggered by autonuma, caused by a
patch we merged earlier in v4.10 to prevent the kernel executing
userspace.
- We weren't marking host IPIs properly for KVM in the OPAL ICP
backend.
- The ERAT flushing on radix was missing an isync and was incorrectly
marked as DD1 only.
- The powernv CPU hotplug code was missing a wakeup type and failing
to flush the interrupt correctly when using OPAL ICP
Thanks to Benjamin Herrenschmidt"
* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Properly set "host-ipi" on IPIs
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
powerpc/mm: Fix spurrious segfaults on radix with autonuma
Eric Dumazet [Fri, 10 Feb 2017 00:15:52 +0000 (16:15 -0800)]
l2tp: do not use udp_ioctl()
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue") Fixes: 85584672012e ("udp: Fix udp_poll() and ioctl()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Improve BPF selftests and use the library (net-next tree)
This series brings some fixes to selftests, add the ability to test
unprivileged BPF programs as root and replace bpf_sys.h with calls to the BPF
library.
This is intended for the net-next tree and apply on c0e4dadb3494 ("net: dsa:
mv88e6xxx: Move forward declaration to where it is needed").
Changes since v4:
* align text for function calls as requested by Daniel Borkmann
(bpf_load_program and bpf_map_update_elem)
* rebase
Changes since v3:
* keep the bzero() calls
Changes since v2:
* use the patches from two previous series (unprivileged tests and bpf_sys.h
replacement)
* include one more stdint.h
* rebase on net-next
* add this cover letter
Changes since v1:
* exclude patches not intended for the net-next tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mickaël Salaün [Thu, 9 Feb 2017 23:21:36 +0000 (00:21 +0100)]
bpf: Change the include directory for selftest
Use the tools include directory instead of the installed one to allow
builds from other kernels.
Signed-off-by: Mickaël Salaün <mic@digikod.net> Cc: Alexei Starovoitov <ast@fb.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Mickaël Salaün [Thu, 9 Feb 2017 23:21:35 +0000 (00:21 +0100)]
tools: Sync {,tools/}include/uapi/linux/bpf.h
The tools version of this header is out of date; update it to the latest
version from kernel header.
Synchronize with the following commits:
* b95a5c4db09b ("bpf: add a longest prefix match trie map implementation")
* a5e8c07059d0 ("bpf: add bpf_probe_read_str helper")
* d1b662adcdb8 ("bpf: allow option for setting bpf_l4_csum_replace from scratch")
Signed-off-by: Mickaël Salaün <mic@digikod.net> Cc: Alexei Starovoitov <ast@fb.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Daniel Mack <daniel@zonque.org> Cc: David S. Miller <davem@davemloft.net> Cc: Gianluca Borello <g.borello@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netronome NFP4000 and NFP6000 PF driver
This is a base PF driver for Netronome NFP4000 and NFP6000 chips. This
series doesn't add any exciting new features, it provides a foundation
for supporting more advanced firmware applications.
Patch 1 moves a bitfield-related helper from our BPF code to the global
header.
Patch 2 renames the kernel module and adds a new main file. We were
considering 3-module approach (pf, vf, common netdev library) but
ultimately settled on a single module to keep things simple.
Patch 3 adds support for accessing chip internals. It provides a way of
configuring access windows to different parts of chip memory and issuing
pretty much any commands on chip's NoC.
Patches 4, 5, 6, 7, 8 provide support for accessing and interpreting
various hardware and firmware information structures.
Patch 9 introduces service processor (NSP) ABI. This ABI gives us
access to PHY/SFP module configuration and information as well as
methods for unloading and loading application firmware.
Patches 10 and 11 modify the existing netdev code to make it possible
to support multi-port devices (sharing a PCI device).
Patch 12 adds a new driver probe path which will be used for the PF
PCI device IDs. It utilizes the newly added infrastructure and is able
to load application FW and spawn netdevs for all card's ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:37 +0000 (09:17 -0800)]
nfp: allocate irqs in lower driver
PF services multiple ports using single PCI device therefore
IRQs can no longer be allocated in the netdev code. Lower
portion of the driver has to allocate the IRQs and hand them
out to ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:35 +0000 (09:17 -0800)]
nfp: add support for service processor access
NFP Service Processor (NSP) is an ARM core inside the chip which
is responsible for management and control functions. Add support
for chip reset, FW load and external module access using the NSP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:32 +0000 (09:17 -0800)]
nfp: add support for reading nffw info
NFFW info is a resource which contains information about
the loaded application firmware. Add code which will allow
us to decode it and retrieve MIP location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:31 +0000 (09:17 -0800)]
nfp: add hwinfo support
Hwinfo is a simple key=value store of information which is read
from the flash and populated during chip power on. Add code to
look up information in it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:30 +0000 (09:17 -0800)]
nfp: add support for resources
Resource table is an array placed in a well defined location
in device's memory which describes device resources and contains
locks which have to be acquired to use them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:29 +0000 (09:17 -0800)]
nfp: add CPP access core
Command Push Pull is the name of NFP's network on a chip.
PCIe PF can access the interconnect through a number of mappings
controlled via Base Access Registers. BARs allow the PF to issue
pretty much any command or address any memory on the chip.
Add appropriate logic and a handful of helper for simple operations
like reading scalars from memories.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 9 Feb 2017 17:17:28 +0000 (09:17 -0800)]
nfp: rename the driver and add new main file
Support for the PF driver is about to be added and will share
much of the code. When the VF driver was added we planned to
maintain the PF driver as a separate module but have decided
that for our simple use case just maintaining a single module
is more reasonable. Rename the driver to just "nfp" and update
the Kconfig.
While at it remove latent references to NFP3200.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 9 Feb 2017 14:54:33 +0000 (15:54 +0100)]
devlink: fix the name of eswitch commands
The eswitch_[gs]et command is supposed to be similar to port_[gs]et
command - for multiple eswitch attributes. However, when it was introduced
by 08f4b5918b2d ("net/devlink: Add E-Switch mode control") it was wrongly
named with the word "mode" in it. So fix this now, make the oririnal
enum value existing but obsolete.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Feb 2017 19:31:51 +0000 (14:31 -0500)]
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Feb 2017 18:51:05 +0000 (13:51 -0500)]
Merge branch 'dsa-phy-include'
Florian Fainelli says:
====================
net: dsa: remove unnecessary phy.h include
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
In order to make this change, several drivers need to be updated to
include necessary headers that they were picking up through this
include. This has resulted in a much larger patch series.
I'm assuming the 0-day builder has had 24 hours with this series, and
hasn't reported any further issues with it - the last issue was two
weeks ago (before I became ill) which I fixed over the last weekend.
I'm hoping this doesn't conflict with what's already in net-next...
David, this should probably go via your tree considering the diffstat.
Changes in v2:
- took Russell's patch series
- removed Qualcomm EMAC patch
- rebased against net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:03:05 +0000 (15:03 -0800)]
net: dsa: remove unnecessary phy*.h includes
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:03:04 +0000 (15:03 -0800)]
net: ath5k: fix build errors when linux/phy*.h is removed from net/dsa.h
Fix these errors reported by the 0-day builder by replacing the
linux/export.h include with linux/module.h.
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1463:1: warning: data definition has no type or storage class
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1468:1: warning: data definition has no type or storage class
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
static void __exit __driver##_exit(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
static int __init __driver##_init(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:03:03 +0000 (15:03 -0800)]
net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
Add linux/module.h to both these files.
drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
Add linux/moduleparam.h to this file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(b) the multiple *_initcall() statements, each of which are translated
to a module_init() call when attempting a module build, become
aliases to init_module(). Having more than one alias will cause a
build error.
Hence, rather than adding a linux/module.h include, remove the redundant
MODULE_*() from this file.
Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:03:01 +0000 (15:03 -0800)]
iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h
drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
Add linux/module.h to iscsi_target_login.c.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:03:00 +0000 (15:03 -0800)]
net: mvneta: fix build errors when linux/phy*.h is removed from net/dsa.h
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 7 Feb 2017 23:02:58 +0000 (15:02 -0800)]
net: bgmac: fix build errors when linux/phy*.h is removed from net/dsa.h
drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
Add linux/phy.h to bgmac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log