Mathias Nyman [Thu, 17 Jun 2021 15:03:52 +0000 (18:03 +0300)]
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Kyle Tso [Wed, 16 Jun 2021 09:01:02 +0000 (17:01 +0800)]
usb: typec: tcpm: Relax disconnect threshold during power negotiation
If the voltage is being decreased in power negotiation, the Source will
set the power supply to operate at the new voltage level before sending
PS_RDY. Relax the threshold before sending Request Message so that it
will not race with Source which begins to adjust the voltage right after
it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends
Accept Message (non-PPS).
The real threshold will be set after Sink receives PS_RDY Message.
usb: typec: tcpci: Fix up sink disconnect thresholds for PD
"Table 4-3 VBUS Sink Characteristics" of "Type-C Cable and Connector
Specification" defines the disconnect voltage thresholds of various
configurations. This change fixes the disconnect threshold voltage
calculation based on vSinkPD_min and vSinkDisconnectPD as defined
by the table.
arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub
Add nodes for the onboard USB hub on trogdor devices. Remove the
'always-on' property from the hub regulator, since the regulator
is now managed by the onboard_usb_hub driver.
usb: host: xhci-plat: Create platform device for onboard hubs in probe()
Call onboard_hub_create/destroy_pdevs() from _probe()/_remove()
to create/destroy platform devices for onboard USB hubs that may
be connected to the root hub of the controller. These functions
are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct xhci_hcd to keep track of the onboard hub
platform devices that are owned by the xHCI.
of/platform: Add stubs for of_platform_device_create/destroy()
Code for platform_device_create() and of_platform_device_destroy() is
only generated if CONFIG_OF_ADDRESS=y. Add stubs to avoid unresolved
symbols when CONFIG_OF_ADDRESS is not set.
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dt-bindings: usb: Add binding for Realtek RTS5411 hub controller
The Realtek RTS5411 is a USB 3.0 hub controller with 4 ports.
This initial version of the binding only describes USB related
aspects of the RTS5411, it does not cover the option of
connecting the controller as an i2c slave.
Chunfeng Yun [Tue, 8 Jun 2021 07:57:35 +0000 (15:57 +0800)]
usb: mtu3: use enum usb_role instead of private defined ones
Now we mainly use usb-role-switch to set dual role mode, and all
three ways supported use the same function to switch mode, use
usb_role enum will make code clear
Chunfeng Yun [Tue, 8 Jun 2021 07:57:32 +0000 (15:57 +0800)]
usb: mtu3: power down port when power down device IP
When power down device IP, we can also power down device port,
then power on the port again when power on device ip, it's helpful
to make device ip enter ip sleep mode.
Tong Tiangen [Fri, 11 Jun 2021 01:40:55 +0000 (09:40 +0800)]
usb: isp1760: Fix meaningless check in isp1763_run()
Remove attribution to retval before check, which make it completely
meaningless, and does't check what it was supposed: the return
value of the timed function to set up configuration flag.
Fixes: 60d789f3bfbb ("usb: isp1760: add support for isp1763") Tested-by: Rui Miguel Silva <rui.silva@linaro.org> Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Tong Tiangen <tongtiangen@huawei.com> Link: https://lore.kernel.org/r/20210611014055.68551-1-tongtiangen@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Osipenko [Sun, 13 Jun 2021 14:59:36 +0000 (17:59 +0300)]
usb: phy: tegra: Correct definition of B_SESS_VLD_WAKEUP_EN bit
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Osipenko [Sun, 13 Jun 2021 14:59:35 +0000 (17:59 +0300)]
usb: phy: tegra: Wait for VBUS wakeup status deassertion on suspend
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Yang [Sat, 12 Jun 2021 00:31:28 +0000 (19:31 -0500)]
usb: gadget: fsl: properly remove remnant of MXC support
Commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
didn't remove all the MXC related stuff which can cause build problem
for LS1021 when enabled again in Kconfig. This patch remove all the
remnants.
Tony Lindgren [Fri, 4 Jun 2021 08:05:36 +0000 (11:05 +0300)]
usb: musb: Implement tracing for state change events
The devctl register on musb is the only way to get state information
on musb. The hardware can easily get confused because it tries to do
things on it's own automagically, and things like slow VBUS rise can
make things fail.
Let's make it easier to debug the ongoing state change issues that
keep popping up on regular basis and add tracing support.
With these changes we can easily trace musb state change events with:
Tony Lindgren [Fri, 4 Jun 2021 08:05:35 +0000 (11:05 +0300)]
usb: musb: Simplify cable state handling
Simplify cable state handling a bit to leave out duplicated code.
We are just scheduling work and showing state info if a recheck is
needed. No intended functional changes.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Andreas Kemnade <andreas@kemnade.info> Cc: Bhushan Shah <bshah@kde.org> Cc: Drew Fustini <drew@beagleboard.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210604080536.12185-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 13 Jun 2021 19:41:47 +0000 (12:41 -0700)]
Merge tag 'perf-tools-fixes-for-v5.13-2021-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Correct buffer copying when peeking events
- Sync cpufeatures/disabled-features.h header with the kernel sources
* tag 'perf-tools-fixes-for-v5.13-2021-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
tools headers cpufeatures: Sync with the kernel sources
perf session: Correct buffer copying when peeking events
Linus Torvalds [Sun, 13 Jun 2021 19:32:59 +0000 (12:32 -0700)]
Merge tag 'nfs-for-5.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix use-after-free in nfs4_init_client()
Bugfixes:
- Fix deadlock between nfs4_evict_inode() and nfs4_opendata_get_inode()
- Fix second deadlock in nfs4_evict_inode()
- nfs4_proc_set_acl should not change the value of NFS_CAP_UIDGID_NOMAP
- Fix setting of the NFS_CAP_SECURITY_LABEL capability"
* tag 'nfs-for-5.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix second deadlock in nfs4_evict_inode()
NFSv4: Fix deadlock between nfs4_evict_inode() and nfs4_opendata_get_inode()
NFS: FMODE_READ and friends are C macros, not enum types
NFS: Fix a potential NULL dereference in nfs_get_client()
NFS: Fix use-after-free in nfs4_init_client()
NFS: Ensure the NFS_CAP_SECURITY_LABEL capability is set when appropriate
NFSv4: nfs4_proc_set_acl needs to restore NFS_CAP_UIDGID_NOMAP on error.
Linus Torvalds [Sun, 13 Jun 2021 19:25:33 +0000 (12:25 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four reasonably small fixes to the core for scsi host allocation
failure paths.
The root problem is that we're not freeing the memory allocated by
dev_set_name(), which involves a rejig of may of the free on error
paths to do put_device() instead of kfree which, in turn, has several
other knock on ramifications and inspection turned up a few other
lurking bugs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Only put parent device if host state differs from SHOST_CREATED
scsi: core: Put .shost_dev in failure path if host state changes to RUNNING
scsi: core: Fix failure handling of scsi_add_host_with_dma()
scsi: core: Fix error handling of scsi_host_alloc()
Linus Torvalds [Sat, 12 Jun 2021 20:57:49 +0000 (13:57 -0700)]
Merge tag 'riscv-for-linus-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of XIP fixes: one to fix alternatives, and one to turn off the
rest of the features that require code modification
- A fix to a type that was causing some alternatives to break
- A build fix for BUILTIN_DTB
* tag 'riscv-for-linus-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix BUILTIN_DTB for sifive and microchip soc
riscv: alternative: fix typo in macro name
riscv: code patching only works on !XIP_KERNEL
riscv: xip: support runtime trap patching
Feng Tang [Fri, 11 Jun 2021 01:54:42 +0000 (09:54 +0800)]
mm: relocate 'write_protect_seq' in struct mm_struct
0day robot reported a 9.2% regression for will-it-scale mmap1 test
case[1], caused by commit 57efa1fe5957 ("mm/gup: prevent gup_fast from
racing with COW during fork").
Further debug shows the regression is due to that commit changes the
offset of hot fields 'mmap_lock' inside structure 'mm_struct', thus some
cache alignment changes.
From the perf data, the contention for 'mmap_lock' is very severe and
takes around 95% cpu cycles, and it is a rw_semaphore
Before commit 57efa1fe5957 adds the 'write_protect_seq', it happens to
have a very optimal cache alignment layout, as Linus explained:
"and before the addition of the 'write_protect_seq' field, the
mmap_sem was at offset 120 in 'struct mm_struct'.
Which meant that count and owner were in two different cachelines,
and then when you have contention and spend time in
rwsem_down_write_slowpath(), this is probably *exactly* the kind
of layout you want.
Because first the rwsem_write_trylock() will do a cmpxchg on the
first cacheline (for the optimistic fast-path), and then in the
case of contention, rwsem_down_write_slowpath() will just access
the second cacheline.
Which is probably just optimal for a load that spends a lot of
time contended - new waiters touch that first cacheline, and then
they queue themselves up on the second cacheline."
After the commit, the rw_semaphore is at offset 128, which means the
'count' and 'owner' fields are now in the same cacheline, and causes
more cache bouncing.
Currently there are 3 "#ifdef CONFIG_XXX" before 'mmap_lock' which will
affect its offset:
The layout above is on 64 bits system with 0day's default kernel config
(similar to RHEL-8.3's config), in which all these 3 options are 'y'.
And the layout can vary with different kernel configs.
Relayouting a structure is usually a double-edged sword, as sometimes it
can helps one case, but hurt other cases. For this case, one solution
is, as the newly added 'write_protect_seq' is a 4 bytes long seqcount_t
(when CONFIG_DEBUG_LOCK_ALLOC=n), placing it into an existing 4 bytes
hole in 'mm_struct' will not change other fields' alignment, while
restoring the regression.
Link: https://lore.kernel.org/lkml/20210525031636.GB7744@xsang-OptiPlex-9020/ Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Feng Tang <feng.tang@intel.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Jun 2021 19:34:49 +0000 (12:34 -0700)]
Merge tag 'usb-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes for 5.13-rc6.
There are more than I would normally like, but there's been a bunch of
people banging on the gadget and dwc3 and typec code recently for I
think an Android release, which has resulted in a number of small
fixes. It's nice to see companies send fixes upstream for this type of
work, a notable change from years ago.
Anyway, fixes in here are:
- usb-serial device id updates
- usb-serial cp210x driver fixes for broken firmware versions
- typec fixes for crazy charging devices and other reported problems
- dwc3 fixes for reported problems found
- gadget fixes for reported problems
- tiny xhci fixes
- other small fixes for reported issues.
- revert of a problem fix found by linux-next testing
All of these have passed 0-day and linux-next testing with no reported
problems (the revert for the found linux-next build problem included)"
* tag 'usb-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (44 commits)
Revert "usb: gadget: fsl: Re-enable driver for ARM SoCs"
usb: typec: mux: Fix copy-paste mistake in typec_mux_match
usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path
usb: gadget: fsl: Re-enable driver for ARM SoCs
usb: typec: wcove: Use LE to CPU conversion when accessing msg->header
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
usb: misc: brcmstb-usb-pinmap: check return value after calling platform_get_resource()
usb: dwc3: ep0: fix NULL pointer exception
usb: gadget: eem: fix wrong eem header operation
usb: typec: intel_pmc_mux: Put ACPI device using acpi_dev_put()
usb: typec: intel_pmc_mux: Add missed error check for devm_ioremap_resource()
usb: typec: intel_pmc_mux: Put fwnode in error case during ->probe()
usb: typec: tcpm: Do not finish VDM AMS for retrying Responses
usb: fix various gadget panics on 10gbps cabling
usb: fix various gadgets null ptr deref on 10gbps cabling.
usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir
usb: f_ncm: only first packet of aggregate needs to start timer
USB: f_ncm: ncm_bitrate (speed) is unsigned
MAINTAINERS: usb: add entry for isp1760
...
Linus Torvalds [Sat, 12 Jun 2021 19:13:55 +0000 (12:13 -0700)]
Merge tag 'char-misc-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small misc driver fixes for 5.13-rc6 that fix some
reported problems:
- Tiny phy driver fixes for reported issues
- rtsx regression for when the device suspended
- mhi driver fix for a use-after-free
All of these have been in linux-next for a few days with no reported
issues"
* tag 'char-misc-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: rtsx: separate aspm mode into MODE_REG and MODE_CFG
bus: mhi: pci-generic: Fix hibernation
bus: mhi: pci_generic: Fix possible use-after-free in mhi_pci_remove()
bus: mhi: pci_generic: T99W175: update channel name from AT to DUN
phy: Sparx5 Eth SerDes: check return value after calling platform_get_resource()
phy: ralink: phy-mt7621-pci: drop 'of_match_ptr' to fix -Wunused-const-variable
phy: ti: Fix an error code in wiz_probe()
phy: phy-mtk-tphy: Fix some resource leaks in mtk_phy_init()
phy: cadence: Sierra: Fix error return code in cdns_sierra_phy_probe()
phy: usb: Fix misuse of IS_ENABLED
Linus Torvalds [Sat, 12 Jun 2021 19:06:24 +0000 (12:06 -0700)]
Merge tag 'pinctrl-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix some documentation warnings for Allwinner
- Fix duplicated GPIO groups on Qualcomm SDX55
- Fix a double enablement bug in the Ralink driver
- Fix the Qualcomm SC8180x Kconfig so the driver can be selected.
* tag 'pinctrl-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Make it possible to select SC8180x TLMM
pinctrl: ralink: rt2880: avoid to error in calls is pin is already enabled
pinctrl: qcom: Fix duplication in gpio_groups
pinctrl: aspeed: Fix minor documentation error
Linus Torvalds [Sat, 12 Jun 2021 18:59:58 +0000 (11:59 -0700)]
Merge tag 'block-5.13-2021-06-12' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes that should go into 5.13:
- Fix a regression deadlock introduced in this release between open
and remove of a bdev (Christoph)
- Fix an async_xor md regression in this release (Xiao)
- Fix bcache oversized read issue (Coly)"
* tag 'block-5.13-2021-06-12' of git://git.kernel.dk/linux-block:
block: loop: fix deadlock between open and remove
async_xor: check src_offs is not NULL before updating it
bcache: avoid oversized read request in cache missing code path
bcache: remove bcache device self-defined readahead
Linus Torvalds [Sat, 12 Jun 2021 18:53:20 +0000 (11:53 -0700)]
Merge tag 'io_uring-5.13-2021-06-12' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Just an API change for the registration changes that went into this
release. Better to get it sorted out now than before it's too late"
* tag 'io_uring-5.13-2021-06-12' of git://git.kernel.dk/linux-block:
io_uring: add feature flag for rsrc tags
io_uring: change registration/upd/rsrc tagging ABI
Linus Torvalds [Sat, 12 Jun 2021 18:41:28 +0000 (11:41 -0700)]
Merge tag 'sched-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes:
- Fix performance regression caused by lack of intended batching of
RCU callbacks by over-eager NOHZ-full code.
- Fix cgroups related corruption of load_avg and load_sum metrics.
- Three fixes to fix blocked load, util_sum/runnable_sum and util_est
tracking bugs"
* tag 'sched-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix util_est UTIL_AVG_UNCHANGED handling
sched/pelt: Ensure that *_sum is always synced with *_avg
tick/nohz: Only check for RCU deferred wakeup on user/guest entry when needed
sched/fair: Make sure to update tg contrib for blocked load
sched/fair: Keep load_avg and load_sum synced
Linus Torvalds [Sat, 12 Jun 2021 18:34:49 +0000 (11:34 -0700)]
Merge tag 'perf-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes:
- Fix the NMI watchdog on ancient Intel CPUs
- Remove a misguided, NMI-unsafe KASAN callback from the NMI-safe
irq_work path used by perf.
- Fix uncore events on Ice Lake servers.
- Someone booted maxcpus=1 on an SNB-EP, and the uncore driver
emitted warnings and was probably buggy. Fix it.
- KCSAN found a genuine data race in the core perf code. Somewhat
ironically the bug was introduced through a recent race fix. :-/
In our defense, the new race window was much more narrow. Fix it"
* tag 'perf-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi_watchdog: Fix old-style NMI watchdog regression on old Intel CPUs
irq_work: Make irq_work_queue() NMI-safe again
perf/x86/intel/uncore: Fix M2M event umask for Ice Lake server
perf/x86/intel/uncore: Fix a kernel WARNING triggered by maxcpus=1
perf: Fix data race between pin_count increment/decrement
Linus Torvalds [Sat, 12 Jun 2021 18:10:28 +0000 (11:10 -0700)]
Merge tag 'objtool-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"Two objtool fixes:
- fix a bug that corrupts the code by mistakenly rewriting
conditional jumps
- fix another bug generating an incorrect ELF symbol table
during retpoline rewriting"
* tag 'objtool-urgent-2021-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Only rewrite unconditional retpoline thunk calls
objtool: Fix .symtab_shndx handling for elf_create_undef_symbol()
Alexandre Ghiti [Fri, 4 Jun 2021 12:06:39 +0000 (14:06 +0200)]
riscv: Fix BUILTIN_DTB for sifive and microchip soc
Fix BUILTIN_DTB config which resulted in a dtb that was actually not
built into the Linux image: in the same manner as Canaan soc does,
create an object file from the dtb file that will get linked into the
Linux image.
Linus Torvalds [Sat, 12 Jun 2021 00:05:03 +0000 (17:05 -0700)]
Merge tag 'trace-v5.13-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix the length check in the temp buffer filter
- Fix build failure in bootconfig tools for "fallthrough" macro
- Fix error return of bootconfig apply_xbc() routine
* tag 'trace-v5.13-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Correct the length check which causes memory corruption
ftrace: Do not blindly read the ip address in ftrace_bug()
tools/bootconfig: Fix a build error accroding to undefined fallthrough
tools/bootconfig: Fix error return code in apply_xbc()
Linus Torvalds [Fri, 11 Jun 2021 19:33:38 +0000 (12:33 -0700)]
Merge tag 'drm-fixes-2021-06-11' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Another week of fixes, nothing too crazy, but a few all over the
place.
Two locking fixes in the core/ttm area, a couple of small driver fixes
(radeon, sun4i, mcde, vc4). Then msm and amdgpu have a set of fixes
each, mostly for smaller things, though the msm has a DSI fix for a
black screen.
I haven't seen any intel fixes this week so they may have a few that
may or may not wait for next week.
drm:
- auth locking fix
ttm:
- locking fix
amdgpu:
- Use kvzmalloc in amdgu_bo_create
- Use drm_dbg_kms for reporting failure to get a GEM FB
- Fix some register offsets for Sienna Cichlid
- Fix fall-through warning
* tag 'drm-fixes-2021-06-11' of git://anongit.freedesktop.org/drm/drm:
drm/msm/dsi: Stash away calculated vco frequency on recalc
drm: Lock pointer access in drm_master_release()
drm/mcde: Fix off by 10^3 in calculation
drm/msm/a6xx: avoid shadow NULL reference in failure path
drm/msm/a6xx: fix incorrectly set uavflagprd_inv field for A650
drm/msm/a6xx: update/fix CP_PROTECT initialization
radeon: use memcpy_to/fromio for UVD fw upload
drm/amd/pm: Fix fall-through warning for Clang
drm/amdgpu: Fix incorrect register offsets for Sienna Cichlid
drm/amdgpu: Use drm_dbg_kms for reporting failure to get a GEM FB
drm/amdgpu: switch kzalloc to kvzalloc in amdgpu_bo_create
drm/msm: Init mm_list before accessing it for use_vram path
drm: Fix use-after-free read in drm_getunique()
drm/vc4: fix vc4_atomic_commit_tail() logic
drm/ttm: fix deref of bo->ttm without holding the lock v2
drm/sun4i: dw-hdmi: Make HDMI PHY into a platform device
Linus Torvalds [Fri, 11 Jun 2021 17:53:43 +0000 (10:53 -0700)]
Merge tag 'acpi-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a problematic recent commit and fix a regression
introduced during the 5.12 development cycle.
Specifics:
- Revert recent commit that attempted to fix the FACS table reference
counting but introduced a problem with accessing the hardware
signature after hibernation (Zhang Rui).
- Fix regression in the _OSC handling that broke the loading of ACPI
tables on some systems (Mika Westerberg)"
* tag 'acpi-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Pass the same capabilities to the _OSC regardless of the query flag
Revert "ACPI: sleep: Put the FACS table after using it"
Commit c76f48eb5c08 ("block: take bd_mutex around delete_partitions in
del_gendisk") adds disk->part0->bd_mutex in del_gendisk(), this way
causes the following AB/BA deadlock between removing loop and opening
loop:
Add a new Lo_deleting state to remove the need for clearing
->private_data and thus holding loop_ctl_mutex in the ioctl
LOOP_CTL_REMOVE path.
Based on an analysis and earlier patch from
Ming Lei <ming.lei@redhat.com>.
Reported-by: Colin Ian King <colin.king@canonical.com> Fixes: c76f48eb5c08 ("block: take bd_mutex around delete_partitions in del_gendisk") Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210605140950.5800-1-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 11 Jun 2021 17:47:10 +0000 (10:47 -0700)]
Merge tag 'sound-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit more commits than expected at this time, but likely it's the
last shot before the final.
Many of changes are device-specific fix-ups for various ASoC drivers,
while a few usual HD-audio quirks and a FireWire fix, as well as a
couple of ALSA / ASoC core fixes.
All look nice and small, and nothing to scare much"
* tag 'sound-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix race of snd_seq_timer_open()
ALSA: hda/realtek: fix mute/micmute LEDs for HP ZBook Power G8
ALSA: hda/realtek: headphone and mic don't work on an Acer laptop
ASoC: qcom: lpass-cpu: Fix pop noise during audio capture begin
ALSA: firewire-lib: fix the context to call snd_pcm_stop_xrun()
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 840 Aero G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP EliteBook x360 1040 G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Elite Dragonfly G2
ASoC: rt5682: Fix the fast discharge for headset unplugging in soundwire mode
ASoC: tas2562: Fix TDM_CFG0_SAMPRATE values
ASoC: meson: gx-card: fix sound-dai dt schema
ASoC: AMD Renoir: Remove fix for DMI entry on Lenovo 2020 platforms
ASoC: AMD Renoir - add DMI entry for Lenovo 2020 AMD platforms
ASoC: SOF: reset enabled_cores state at suspend
ASoC: fsl-asoc-card: Set .owner attribute when registering card.
ASoC: topology: Fix spelling mistake "vesion" -> "version"
ASoC: rt5659: Fix the lost powers for the HDA header
ASoC: core: Fix Null-point-dereference in fmt_single_name()
Tor Vic [Thu, 10 Jun 2021 20:58:06 +0000 (20:58 +0000)]
x86, lto: Pass -stack-alignment only on LLD < 13.0.0
Since LLVM commit 3787ee4, the '-stack-alignment' flag has been dropped
[1], leading to the following error message when building a LTO kernel
with Clang-13 and LLD-13:
ld.lld: error: -plugin-opt=-: ld.lld: Unknown command line argument
'-stack-alignment=8'. Try 'ld.lld --help'
ld.lld: Did you mean '--stackrealign=8'?
It also appears that the '-code-model' flag is not necessary anymore
starting with LLVM-9 [2].
Drop '-code-model' and make '-stack-alignment' conditional on LLD < 13.0.0.
These flags were necessary because these flags were not encoded in the
IR properly, so the link would restart optimizations without them. Now
there are properly encoded in the IR, and these flags exposing
implementation details are no longer necessary.
Linus Torvalds [Fri, 11 Jun 2021 17:07:50 +0000 (10:07 -0700)]
Merge tag 'hwmon-for-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fixes for tps23861, scpi-hwmon, and corsair-psu drivers, plus a
bindings fix for TI ADS7828"
* tag 'hwmon-for-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (tps23861) correct shunt LSB values
hwmon: (tps23861) set current shunt value
hwmon: (tps23861) define regmap max register
hwmon: (scpi-hwmon) shows the negative temperature properly
hwmon: (corsair-psu) fix suspend behavior
dt-bindings: hwmon: Fix typo in TI ADS7828 bindings
Linus Torvalds [Fri, 11 Jun 2021 17:02:30 +0000 (10:02 -0700)]
Merge tag 'mmc-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes to the Renesas SDHI driver:
- Fix HS400 on R-Car M3-W+
- Abort tuning when timeout detected"
* tag 'mmc-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: Fix HS400 on R-Car M3-W+
mmc: renesas_sdhi: abort tuning when timeout detected
JC Kuo [Wed, 20 Jan 2021 07:34:14 +0000 (15:34 +0800)]
usb: xhci: tegra: Enable ELPG for runtime/system PM
This commit implements the complete programming sequence for ELPG
entry and exit.
1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk()
and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL
sleepwalk and wake detection circuits to maintain USB lines level
and respond to wake events (wake-on-connect, wake-on-disconnect,
device-initiated-wake).
2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk()
and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and
wake detection circuits.
At runtime suspend, XUSB host controller can enter ELPG to reduce
power consumption. When XUSB PADCTL wake detection circuit detects
a wake event, an interrupt will be raised. xhci-tegra driver then
will invoke pm_runtime_resume() for xhci-tegra.
Runtime resume could also be triggered by protocol drivers, this is
the host-initiated-wake event. At runtime resume, xhci-tegra driver
brings XUSB host controller out of ELPG to handle the wake events.
The same ELPG enter/exit procedure will be performed for system
suspend/resume path so USB devices can remain connected across SC7.
JC Kuo [Wed, 20 Jan 2021 07:34:13 +0000 (15:34 +0800)]
usb: xhci: tegra: Unlink power domain devices
This commit unlinks xhci-tegra platform device with SS/host power
domain devices. Reasons for this change is - at ELPG entry, PHY
sleepwalk and wake configuration need to be done before powering
down SS/host partitions, and PHY need be powered off after powering
down SS/host partitions. Sequence looks like roughly below:
tegra_xusb_enter_elpg() -> xhci_suspend()
-> enable PHY sleepwalk and wake if needed
-> power down SS/host partitions
-> power down PHY
If SS/host power domains are linked to xhci-tegra platform device, we
are not able to perform the sequence like above.
This commit introduces:
1. tegra_xusb_unpowergate_partitions() to power up SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_get_sync() to request power
driver to power up partitions; If power domain devices are not
available, tegra_powergate_sequence_power_up() will be used to
power up partitions.
2. tegra_xusb_powergate_partitions() to power down SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_put_sync() to request power
driver to power down partitions; If power domain devices are not
available, tegra_powergate_power_off() will be used to power down
partitions.
tools headers cpufeatures: Sync with the kernel sources
To pick the changes in:
fb35d30fe5b06cc2 ("x86/cpufeatures: Assign dedicated feature word for CPUID_0x8000001F[EAX]") e7b6385b01d8e9fb ("x86/cpufeatures: Add Intel SGX hardware bits") 1478b99a76534b6c ("x86/cpufeatures: Mark ENQCMD as disabled when configured out")
That don't cause any change in the tools, just silences this perf build
warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/disabled-features.h' differs from latest version at 'arch/x86/include/asm/disabled-features.h'
diff -u tools/arch/x86/include/asm/disabled-features.h arch/x86/include/asm/disabled-features.h
Cc: Borislav Petkov <bp@suse.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sat, 5 Jun 2021 05:29:57 +0000 (13:29 +0800)]
perf session: Correct buffer copying when peeking events
When peeking an event, it has a short path and a long path. The short
path uses the session pointer "one_mmap_addr" to directly fetch the
event; and the long path needs to read out the event header and the
following event data from file and fill into the buffer pointer passed
through the argument "buf".
The issue is in the long path that it copies the event header and event
data into the same destination address which pointer "buf", this means
the event header is overwritten. We are just lucky to run into the
short path in most cases, so we don't hit the issue in the long path.
This patch adds the offset "hdr_sz" to the pointer "buf" when copying
the event data, so that it can reserve the event header which can be
used properly by its caller.
Fixes: 5a52f33adf02 ("perf session: Add perf_session__peek_event()") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210605052957.1070720-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.13-rc6
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
* tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
Turns out this breaks the build. We had numerous reports of problems
from linux-next and 0-day about this not working properly, so revert it
for now until it can be figured out properly.
The build errors are:
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize'
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release'
fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init'
fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kernel test robot <lkp@intel.com> Fixes: e0e8b6abe8c8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs") Cc: stable <stable@vger.kernel.org> Cc: Joel Stanley <joel@jms.id.au> Cc: Leo Li <leoyang.li@nxp.com> Cc: Peter Chen <peter.chen@nxp.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Felipe Balbi <balbi@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Ran Wang <ran.wang_1@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
while the rewrite can only handle JMP/CALL to the thunks. The result
is the alternative wrecking the code. Make sure to skip writing the
alternatives for conditional branches.
Xiao Ni [Fri, 28 May 2021 06:16:38 +0000 (14:16 +0800)]
async_xor: check src_offs is not NULL before updating it
When PAGE_SIZE is greater than 4kB, multiple stripes may share the same
page. Thus, src_offs is added to async_xor_offs() with array of offsets.
However, async_xor() passes NULL src_offs to async_xor_offs(). In such
case, src_offs should not be updated. Add a check before the update.
Fixes: ceaf2966ab08(async_xor: increase src_offs when dropping destination page) Cc: stable@vger.kernel.org # v5.10+ Reported-by: Oleksandr Shchirskyi <oleksandr.shchirskyi@linux.intel.com> Tested-by: Oleksandr Shchirskyi <oleksandr.shchirskyi@intel.com> Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <song@kernel.org>
Dave Airlie [Fri, 11 Jun 2021 01:17:09 +0000 (11:17 +1000)]
Merge tag 'amd-drm-fixes-5.13-2021-06-09' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.13-2021-06-09:
amdgpu:
- Use kvzmalloc in amdgu_bo_create
- Use drm_dbg_kms for reporting failure to get a GEM FB
- Fix some register offsets for Sienna Cichlid
- Fix fall-through warning
Dave Airlie [Fri, 11 Jun 2021 00:59:49 +0000 (10:59 +1000)]
Merge tag 'drm-misc-fixes-2021-06-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One fix for snu4i that prevents it from probing, two locking fixes for
ttm and drm_auth, one off-by-x1000 fix for mcde and a fix for vc4 to
prevent an out-of-bounds access.
Jisheng Zhang [Mon, 10 May 2021 16:28:38 +0000 (00:28 +0800)]
riscv: code patching only works on !XIP_KERNEL
Some features which need code patching such as KPROBES, DYNAMIC_FTRACE
KGDB can only work on !XIP_KERNEL. Add dependencies for these features
that rely on code patching.
Vitaly Wool [Mon, 31 May 2021 08:53:42 +0000 (11:53 +0300)]
riscv: xip: support runtime trap patching
RISCV_ERRATA_ALTERNATIVE patches text at runtime which is currently
not possible when the kernel is executed from the flash in XIP mode.
Since runtime patching concerns only traps at the moment, let's just
have all the traps reside in RAM anyway if RISCV_ERRATA_ALTERNATIVE
is set. Thus, these functions will be patch-able even when the .text
section is in flash.
Pavel Begunkov [Thu, 10 Jun 2021 15:37:38 +0000 (16:37 +0100)]
io_uring: add feature flag for rsrc tags
Add IORING_FEAT_RSRC_TAGS indicating that io_uring supports a bunch of
new IORING_REGISTER operations, in particular
IORING_REGISTER_[FILES[,UPDATE]2,BUFFERS[2,UPDATE]] that support rsrc
tagging, and also indicating implemented dynamic fixed buffer updates.
Pavel Begunkov [Thu, 10 Jun 2021 15:37:37 +0000 (16:37 +0100)]
io_uring: change registration/upd/rsrc tagging ABI
There are ABI moments about recently added rsrc registration/update and
tagging that might become a nuisance in the future. First,
IORING_REGISTER_RSRC[_UPD] hide different types of resources under it,
so breaks fine control over them by restrictions. It works for now, but
once those are wanted under restrictions it would require a rework.
It was also inconvenient trying to fit a new resource not supporting
all the features (e.g. dynamic update) into the interface, so better
to return to IORING_REGISTER_* top level dispatching.
Second, register/update were considered to accept a type of resource,
however that's not a good idea because there might be several ways of
registration of a single resource type, e.g. we may want to add
non-contig buffers or anything more exquisite as dma mapped memory.
So, remove IORING_RSRC_[FILE,BUFFER] out of the ABI, and place them
internally for now to limit changes.
Olivier Langlois has been struggling with coredumps being incompletely written in
processes using io_uring.
Olivier Langlois <olivier@trillion01.com> writes:
> io_uring is a big user of task_work and any event that io_uring made a
> task waiting for that occurs during the core dump generation will
> generate a TIF_NOTIFY_SIGNAL.
>
> Here are the detailed steps of the problem:
> 1. io_uring calls vfs_poll() to install a task to a file wait queue
> with io_async_wake() as the wakeup function cb from io_arm_poll_handler()
> 2. wakeup function ends up calling task_work_add() with TWA_SIGNAL
> 3. task_work_add() sets the TIF_NOTIFY_SIGNAL bit by calling
> set_notify_signal()
The coredump code deliberately supports being interrupted by SIGKILL,
and depends upon prepare_signal to filter out all other signals. Now
that signal_pending includes wake ups for TIF_NOTIFY_SIGNAL this hack
in dump_emitted by the coredump code no longer works.
Make the coredump code more robust by explicitly testing for all of
the wakeup conditions the coredump code supports. This prevents
new wakeup conditions from breaking the coredump code, as well
as fixing the current issue.
The filesystem code that the coredump code uses already limits
itself to only aborting on fatal_signal_pending. So it should
not develop surprising wake-up reasons either.
v2: Don't remove the now unnecessary code in prepare_signal.
Cc: stable@vger.kernel.org Fixes: 12db8b690010 ("entry: Add support for TIF_NOTIFY_SIGNAL") Reported-by: Olivier Langlois <olivier@trillion01.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 10 Jun 2021 19:01:22 +0000 (12:01 -0700)]
Merge branch 'for-5.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"This is a high priority but low risk fix for a cgroup1 bug where
rename(2) can change a cgroup's name to something which can break
parsing of /proc/PID/cgroup"
* 'for-5.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup1: don't allow '\n' in renaming
Bjorn Andersson [Thu, 10 Jun 2021 00:21:32 +0000 (17:21 -0700)]
usb: typec: mux: Fix copy-paste mistake in typec_mux_match
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes") Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mayank Rana [Wed, 9 Jun 2021 07:35:35 +0000 (00:35 -0700)]
usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path
If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface") Cc: stable@vger.kernel.org Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joel Stanley [Thu, 10 Jun 2021 03:49:57 +0000 (13:19 +0930)]
usb: gadget: fsl: Re-enable driver for ARM SoCs
The commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.
FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad8600 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.
This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:
Andy Shevchenko [Wed, 9 Jun 2021 17:22:02 +0000 (20:22 +0300)]
usb: typec: wcove: Use LE to CPU conversion when accessing msg->header
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together") Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support") Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep around the debugfs "root" directory for the
dwc3 device. Instead, look it up anytime we need to find it. This will
help when callers get out-of-order and we had the potential to have a
"stale" pointer around for the root dentry, as has happened in the past.
Linus Torvalds [Thu, 10 Jun 2021 17:53:04 +0000 (10:53 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A mixture of small bug fixes and a small security issue:
- WARN_ON when IPoIB is automatically moved between namespaces
- Long standing bug where mlx5 would use the wrong page for the
doorbell recovery memory if fork is used
- Security fix for mlx4 that disables the timestamp feature
- Several crashers for mlx5
- Plug a recent mlx5 memory leak for the sig_mr"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix initializing CQ fragments buffer
RDMA/mlx5: Delete right entry from MR signature database
RDMA: Verify port when creating flow rule
RDMA/mlx5: Block FDB rules when not in switchdev mode
RDMA/mlx4: Do not map the core_clock page to user space unless enabled
RDMA/mlx5: Use different doorbell memory for different processes
RDMA/ipoib: Fix warning caused by destroying non-initial netns
Robert Marko [Wed, 9 Jun 2021 22:07:27 +0000 (00:07 +0200)]
hwmon: (tps23861) set current shunt value
TPS23861 has a configuration bit for setting of the
current shunt value used on the board.
Its bit 0 of the General Mask 1 register.
According to the datasheet bit values are:
0 for 255 mOhm (Default)
1 for 250 mOhm
So, configure the bit before registering the hwmon
device according to the value passed in the DTS or
default one if none is passed.
This caused potentially reading slightly skewed values
due to max current value being 1.02A when 250mOhm shunt
is used instead of 1.0A when 255mOhm is used.
Robert Marko [Wed, 9 Jun 2021 22:07:26 +0000 (00:07 +0200)]
hwmon: (tps23861) define regmap max register
Define the max register address the device supports.
This allows reading the whole register space via
regmap debugfs, without it only register 0x0 is visible.
Takashi Iwai [Thu, 10 Jun 2021 15:20:59 +0000 (17:20 +0200)]
ALSA: seq: Fix race of snd_seq_timer_open()
The timer instance per queue is exclusive, and snd_seq_timer_open()
should have managed the concurrent accesses. It looks as if it's
checking the already existing timer instance at the beginning, but
it's not right, because there is no protection, hence any later
concurrent call of snd_seq_timer_open() may override the timer
instance easily. This may result in UAF, as the leftover timer
instance can keep running while the queue itself gets closed, as
spotted by syzkaller recently.
For avoiding the race, add a proper check at the assignment of
tmr->timeri again, and return -EBUSY if it's been already registered.
Johan Hovold [Wed, 9 Jun 2021 16:15:09 +0000 (18:15 +0200)]
USB: serial: cp210x: fix CP2102N-A01 modem control
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org Reported-by: David Frey <dpfrey@gmail.com> Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com> Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com> Fixes: f61309d9c96a ("USB: serial: cp210x: set IXOFF thresholds") Cc: stable@vger.kernel.org # 5.12 Signed-off-by: Johan Hovold <johan@kernel.org>
Stephen Boyd [Tue, 8 Jun 2021 19:55:19 +0000 (12:55 -0700)]
drm/msm/dsi: Stash away calculated vco frequency on recalc
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc33875 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: Abhinav Kumar <abhinavk@codeaurora.org> Fixes: 001d8dc33875 ("drm/msm/dsi: remove temp data from global pll structure") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org Signed-off-by: Rob Clark <robdclark@chromium.org>