Linus Walleij [Fri, 6 Dec 2019 09:43:01 +0000 (10:43 +0100)]
drm/gma500: Pass GPIO for Intel MID using descriptors
The GMA500 driver is using the legacy GPIO API to fetch
three optional display control GPIO lines from the SFI
description used by the Medfield platform.
Switch this over to use GPIO descriptors and delete the
custom platform data.
We create three new static locals in the tc35876x bridge
code but it is hardly any worse than the I2C client static
local already there: I tried first to move it to the DRM
driver state container but there are workarounds for
probe order in the code so I just stayed off it, as the
result is unpredictable.
People wanting to do a more throrugh and proper cleanup
of the GMA500 driver can work on top of this, I can't
solve much more since I don't have access to the hardware,
I can only attempt to tidy up my GPIO corner.
Jerry Han [Thu, 12 Dec 2019 11:52:08 +0000 (19:52 +0800)]
drm/panel: Add Boe Himax8279d MIPI-DSI LCD panel
Support Boe Himax8279d 8.0" 1200x1920 TFT LCD panel, it is a MIPI DSI
panel.
V11:
- Use the backlight support in drm_panel to simplify the driver (Sam)
V10:
- Adjust init code, make the format more concise (Emil)
V9:
- kill off default_off_cmds (Emil)
- use mipi_dsi_dcs_set_display_{on,off} in their enable/disable
callbacks. (Emil)
- Adjusting the delay function (Emil)
V8:
- modify PARENTHESIS_ALIGNMENT format (Sam)
- use gpios are required API replace optional gpio API (Emil)
V7:
- Modify communication address
V6:
- Add the information of the reviewer
- Remove unnecessary delays, The udelay_range code gracefully returns
without hitting the scheduler on a delay of 0. (Derek)
- Merge the same data structures, like display_mode and off_cmds (Derek)
- Optimize the processing of results returned by
devm_gpiod_get_optional (Derek)
V5:
- Add the information of the reviewer (Sam)
- Delete unnecessary header files #include <linux/fb.h> (Sam)
- The config DRM_PANEL_BOE_HIMAX8279D appears twice. Drop one of them (Sam)
- ADD static, set_gpios function is not used outside this module (Sam)
V4:
- Frefix all function maes with boe_ (Sam)
- Fsed "enable_gpio" replace "reset_gpio", Make it look clearer (Sam)
- Sort include lines alphabetically (Sam)
- Fixed entries in the makefile must be sorted alphabetically (Sam)
- Add send_mipi_cmds function to avoid duplicating the code (Sam)
- Add the necessary delay(reset_delay_t5) between reset and sending
the initialization command (Rock wang)
V2:
- Use SPDX identifier (Sam)
- Use necessary header files replace drmP.h (Sam)
- Delete unnecessary header files #include <linux/err.h> (Sam)
- Specifies a GPIOs array to control the reset timing,
instead of reading "dsi-reset-sequence" data from DTS (Sam)
- Delete backlight_disable() function when already disabled (Sam)
- Use devm_of_find_backlight() replace of_find_backlight_by_node() (Sam)
- Move the necessary data in the DTS to the current file,
like porch, display_mode and Init code etc. (Sam)
- Add compatible device "boe,himax8279d10p" (Sam)
V1:
- Support Boe Himax8279d 8.0" 1200x1920 TFT LCD panel, it is a MIPI DSI
panel.
Signed-off-by: Jerry Han <jerry.han.hq@gmail.com> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Derek Basehore <dbasehore@chromium.org> Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> Reported-by: kbuild test robot <lkp@intel.com> Cc: Jitao Shi <jitao.shi@mediatek.com> Cc: Rock wang <rock_wang@himax.com.cn> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> [fixed boe_panel_get_modes + backlight] Link: https://patchwork.freedesktop.org/patch/msgid/20191212115208.3878-1-jerry.han.hq@gmail.com
1. Drop komeda-CORE product id comparison and put it into the d71_identify
2. Update pipeline node DT-binding:
(a). Skip the needless pipeline DT node.
(b). Return fail if the essential pipeline DT node is missing.
With these changes, for chips in same family no need to change the DT.
Per HW, d71->num_blocks includes reserved blocks but no PERIPH block,
correct the block counting accordingly.
D71 happens to only have one reserved block and periph block, which
hides this counting error.
The udl driver stores the currently active framebuffer to know from
where to accept damage updates.
With the conversion to plane-state damage handling, this is not necessary
any longer. The currently active framebuffer and damaged area are always
stored in the plane state.
The infrastruture for atomic modesetting allows us to use the generic
code for dirty-FB and damage handling. Switch over udl and remove the
driver's implementation. The simple-pipe's update function now picks up
the primary plane's damage and updates a minimal region of the screen.
The current default color depth of 24 bpp is not even supported by
the driver. Being the native format for communicating with the adapter,
16 bpp is the correct choice.
drm/udl: Inline DPMS code into CRTC enable and disable functions
DPMS functionality is only used by the CRTC's enable and disable
functions. Inline the code. The patch also adds symbolic constants
for the blank register and constants; according to udlfb, which is
a bit more detailed than DRM's udl.
v3:
* use symbolic constants for blank, according to udlfb driver
drm/udl: Convert to struct drm_simple_display_pipe
Udl has a single display pipeline with a primary plane; perfect for
simple-pipe helpers. Convert it over. The old encoder and CRTC code
becomes unused and obsolete.
Exported formats for the primary plane are RGB565 and XRGB8888, with
the latter being emulated. The 16-bit format is the default and what
is used when communicating with the device.
This patch enables atomic modesetting for udl devices.
v3:
* remove unused field crtc from struct udl_device
* set crtc_state->no_vblank at beginning of enable()
v2:
* move suspend/resume changes into separate patch
* remove non-atomic code
John Stultz [Tue, 3 Dec 2019 17:26:40 +0000 (17:26 +0000)]
dma-buf: heaps: Add CMA heap to dmabuf heaps
This adds a CMA heap, which allows userspace to allocate
a dma-buf of contiguous memory out of a CMA region.
This code is an evolution of the Android ION implementation, so
thanks to its original author and maintainters:
Benjamin Gaignard, Laura Abbott, and others!
NOTE: This patch only adds the default CMA heap. We will enable
selectively adding other CMA memory regions to the dmabuf heaps
interface with a later patch (which requires a dt binding)
Cc: Laura Abbott <labbott@redhat.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Liam Mark <lmark@codeaurora.org> Cc: Pratik Patel <pratikp@codeaurora.org> Cc: Brian Starkey <Brian.Starkey@arm.com> Cc: Vincent Donnefort <Vincent.Donnefort@arm.com> Cc: Sudipto Paul <Sudipto.Paul@arm.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chenbo Feng <fengc@google.com> Cc: Alistair Strachan <astrachan@google.com> Cc: Hridya Valsaraju <hridya@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Dave Airlie <airlied@gmail.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Reviewed-by: Brian Starkey <brian.starkey@arm.com> Acked-by: Sandeep Patil <sspatil@android.com> Acked-by: Laura Abbott <labbott@redhat.com> Tested-by: Ayan Kumar Halder <ayan.halder@arm.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203172641.66642-5-john.stultz@linaro.org
John Stultz [Tue, 3 Dec 2019 17:26:39 +0000 (17:26 +0000)]
dma-buf: heaps: Add system heap to dmabuf heaps
This patch adds system heap to the dma-buf heaps framework.
This allows applications to get a page-allocator backed dma-buf
for non-contiguous memory.
This code is an evolution of the Android ION implementation, so
thanks to its original authors and maintainters:
Rebecca Schultz Zavin, Colin Cross, Laura Abbott, and others!
Cc: Laura Abbott <labbott@redhat.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Liam Mark <lmark@codeaurora.org> Cc: Pratik Patel <pratikp@codeaurora.org> Cc: Brian Starkey <Brian.Starkey@arm.com> Cc: Vincent Donnefort <Vincent.Donnefort@arm.com> Cc: Sudipto Paul <Sudipto.Paul@arm.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chenbo Feng <fengc@google.com> Cc: Alistair Strachan <astrachan@google.com> Cc: Hridya Valsaraju <hridya@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Dave Airlie <airlied@gmail.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Reviewed-by: Brian Starkey <brian.starkey@arm.com> Acked-by: Sandeep Patil <sspatil@android.com> Acked-by: Laura Abbott <labbott@redhat.com> Tested-by: Ayan Kumar Halder <ayan.halder@arm.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203172641.66642-4-john.stultz@linaro.org
John Stultz [Tue, 3 Dec 2019 17:26:38 +0000 (17:26 +0000)]
dma-buf: heaps: Add heap helpers
Add generic helper dmabuf ops for dma heaps, so we can reduce
the amount of duplicative code for the exported dmabufs.
This code is an evolution of the Android ION implementation, so
thanks to its original authors and maintainters:
Rebecca Schultz Zavin, Colin Cross, Laura Abbott, and others!
Cc: Laura Abbott <labbott@redhat.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Liam Mark <lmark@codeaurora.org> Cc: Pratik Patel <pratikp@codeaurora.org> Cc: Brian Starkey <Brian.Starkey@arm.com> Cc: Vincent Donnefort <Vincent.Donnefort@arm.com> Cc: Sudipto Paul <Sudipto.Paul@arm.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chenbo Feng <fengc@google.com> Cc: Alistair Strachan <astrachan@google.com> Cc: Hridya Valsaraju <hridya@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Dave Airlie <airlied@gmail.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Reviewed-by: Brian Starkey <brian.starkey@arm.com> Acked-by: Sandeep Patil <sspatil@android.com> Acked-by: Laura Abbott <labbott@redhat.com> Tested-by: Ayan Kumar Halder <ayan.halder@arm.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203172641.66642-3-john.stultz@linaro.org
Andrew F. Davis [Tue, 3 Dec 2019 17:26:37 +0000 (17:26 +0000)]
dma-buf: Add dma-buf heaps framework
This framework allows a unified userspace interface for dma-buf
exporters, allowing userland to allocate specific types of memory
for use in dma-buf sharing.
Each heap is given its own device node, which a user can allocate
a dma-buf fd from using the DMA_HEAP_IOC_ALLOC.
This code is an evoluiton of the Android ION implementation,
and a big thanks is due to its authors/maintainers over time
for their effort:
Rebecca Schultz Zavin, Colin Cross, Benjamin Gaignard,
Laura Abbott, and many other contributors!
Cc: Laura Abbott <labbott@redhat.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Liam Mark <lmark@codeaurora.org> Cc: Pratik Patel <pratikp@codeaurora.org> Cc: Brian Starkey <Brian.Starkey@arm.com> Cc: Vincent Donnefort <Vincent.Donnefort@arm.com> Cc: Sudipto Paul <Sudipto.Paul@arm.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chenbo Feng <fengc@google.com> Cc: Alistair Strachan <astrachan@google.com> Cc: Hridya Valsaraju <hridya@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Dave Airlie <airlied@gmail.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Brian Starkey <brian.starkey@arm.com> Acked-by: Sandeep Patil <sspatil@android.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203172641.66642-2-john.stultz@linaro.org
Sam Ravnborg [Tue, 10 Dec 2019 19:47:58 +0000 (20:47 +0100)]
drm/drm_panel: fix EXPORT of drm_panel_of_backlight
Fix link failure for module builds of panels.
The conditional compilation around drm_panel_of_backlight()
was wrong for a module build.
Fix it using IS_ENABLED().
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Fixes: 152dbdeab1b2 ("drm/panel: add backlight support") Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Maxime Ripard <mripard@kernel.org> Cc: dri-devel@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20191210194758.24087-1-sam@ravnborg.org
Daniel Vetter [Wed, 4 Dec 2019 10:00:11 +0000 (11:00 +0100)]
drm/atomic: Update docs around locking and commit sequencing
Both locking and especially sequencing of nonblocking commits have
evolved a lot. The details are all there, but I noticed that the big
picture and connections have fallen behind a bit. Apply polish.
Motivated by some review discussions with Thierry.
drm/ast: Store primary-plane format in struct ast_crtc_state
Reading the primary plane's framebuffer from the CRTC's atomic_flush()
function is fragile as the plane state or framebuffer can be NULL.
Instead, we let the plane's atomic_check() store the framebuffer format
in the CRTC state. The CRTC always receives the framebuffer format that
is currently programmed, or NULL if no mode has been set yet.
AST-specific CRTC state can be placed in the new struct ast_crtc_state.
The atomic check functions of the CRTC and the primary plane will store
the VBIOS mode info and the framebuffer format here. The CRTC will consume
these during atomic_flush().
Introducing atomic_check() for priamry and cursor plane. The functions
validate the plane state and will later set format information for the
CRTC's atomic_flush().
In preparation of an update of the primary-plane code, this patch
changes the arguments of several register-setting functions. No
functional changes are made. The function ast_set_dac_reg() has no
effect and therefore gets removed entirely.
drm/ast: Enable and disable screen in primary-plane functions
Enabling and disabling the screen used to be done in the register
initialization and the DPMS function. None of these places is related
to the screen's output.
Now the primary plane's update and disable functions handle screen
display state. The primary plane can now be switched off without
displaying garbage.
drm/ast: Move modesetting code to CRTC's atomic_flush()
When enabling the CRTC after waking up from a power-saving mode, the
primary plane's framebuffer might be NULL, which leads to a stack trace
as shown below.
* start gdm and wait for it to switch off the display
* wake up the display by pressing a key
CRTC modesetting depends on the new state of the CRTC and the primary
plane's framebuffer. The bugfix moves the modesetting code into the
CRTC's atomic_flush() function, where it is protected from the plane's
framebuffer being NULL.
The CRTC's atomic-enable function, which is the modesetting's original
location, still contains DPMS state handling. It's exactly the inverse
of the atomic-disable function.
v3:
* protect modesetting from from fb == NULL
v2:
* do an atomic check for plane
* reject invisible primary planes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Gerd Hoffmann <kraxel@redhat.com> Fixes: b48e1b6ffd28 ("drm/ast: Add CRTC helpers for atomic modesetting") Cc: Gerd Hoffmann <kraxel@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: "Y.C. Chen" <yc_chen@aspeedtech.com> Cc: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191202111557.15176-2-tzimmermann@suse.de
Neil Armstrong [Mon, 21 Oct 2019 09:15:09 +0000 (11:15 +0200)]
drm/meson: crtc: add OSD1 plane AFBC commit
Finally, setup the VIU registers and start the AFBC decoder to support
displaying AFBC encoded buffers on Amlogic GXM and G12A SoCs.
The RDMA is used here to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a long period of time, producing display glitches.
The vsync irq must still be left enabled otherwise the RDMA modules isn't
trigerred when the interrupt line is masked.
The Amlogic G12A AFBC Decoder pixel input need to be routed diferently
than the Amlogic GXM AFBC decoder, this adds support for routing the
VIU OSD1 pixel source to the AFBC "Mali Unpack" module.
This "Mali Unpack" module is also configured with a static RGBA mapping
for now until we support more pixel formats.
Neil Armstrong [Mon, 21 Oct 2019 09:15:06 +0000 (11:15 +0200)]
drm/meson: plane: add support for AFBC mode for OSD1 plane
This adds all the OSD configuration plumbing to support the AFBC decoders
path to display of the OSD1 plane.
The Amlogic GXM and G12A AFBC decoders are integrated very differently.
The Amlogic GXM has a direct output path to the OSD1 VIU pixel input,
because the GXM AFBC decoder seem to be a custom IP developed by Amlogic.
On the other side, the Amlogic G12A AFBC decoder seems to be an external
IP that emit pixels on an AXI master hooked to a "Mali Unpack" block
feeding the OSD1 VIU pixel input.
This uses a weird "0x1000000" internal HW physical address on both
sides to transfer the pixels.
For Amlogic GXM, the supported pixel formats are the same as the normal
linear OSD1 mode.
On the other side, Amlogic added support for all AFBC v1.2 formats for
the G12A AFBC integration.
For simplicity, we stick to the already supported formats for now.
Neil Armstrong [Mon, 21 Oct 2019 09:15:05 +0000 (11:15 +0200)]
drm/meson: Add AFBCD module driver
This adds the driver for the ARM Framebuffer Compression decoders found
in the Amlogic GXM and G12A SoCs.
The Amlogic GXM and G12A AFBC decoder are totally different, the GXM only
handling only the AFBC v1.0 modes and the G12A decoder handling the
AFBC v1.2 modes.
The G12A AFBC decoder is an external IP integrated in the video pipeline,
and the GXM AFBC decoder seems to the an Amlogic custom decoder more
tighly integrated in the video pipeline.
The GXM AFBC decoder can handle only one AFBC plane for 2 available
OSD planes available in HW, and the G12A AFBC decoder can handle up
to 4 AFBC planes for up to 3 OSD planes available in HW.
The Amlogic GXM supports 16x16 SPARSE and 16x16 SPLIT AFBC buffers up
to 4k.
On the other side, for G12A SPLIT is mandatory in 16x16 block mode, but
for 4k modes 32x8+SPLIT AFBC buffers is manadatory for performances reasons.
The RDMA is used here to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a long period of time, producing display glitches.
For this we use the meson_rdma_writel_sync() which adds the register
write tuple (VPU register offset and register value) to the RDMA buffer
and write the value to the HW.
When enabled, the RDMA is enabled to rewrite the same sequence at the
next VSYNC event, until a new buffer is committed to the OSD plane.
Then the Amlogic G12A is switched to RDMA, the Amlogic GXM Decoder
doesn't need a reset/reprogram at each vsync, but needs to keep the
vsync interrupt enabled to trigger the RDMA module.
Neil Armstrong [Mon, 21 Oct 2019 09:15:04 +0000 (11:15 +0200)]
drm/meson: add RDMA module driver
The VPU embeds a "Register DMA" that can write a sequence of registers
on the VPU AHB bus, either manually or triggered by an internal IRQ
event like VSYNC or a line input counter.
The initial implementation handles a single channel (over 8), triggered
by the VSYNC irq and does not handle the RDMA irq.
The RDMA will be usefull to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a log period of time, producing display glitches.
Neil Armstrong [Mon, 21 Oct 2019 09:15:02 +0000 (11:15 +0200)]
drm/meson: add RDMA register bits defines
The Amlogic VPU embeds a "Register DMA" that can write a sequence of registers
on the VPU AHB bus, either manually or triggered by an internal IRQ event like
VSYNC or a line input counter.
Sam Ravnborg [Sat, 7 Dec 2019 14:03:35 +0000 (15:03 +0100)]
drm/panel: drop drm_device from drm_panel
The panel drivers used drm_panel.drm for two purposes:
1) Argument to drm_mode_duplicate()
2) drm->dev was used in error messages
The first usage is replaced with drm_connector.dev
- drm_connector is already connected to a drm_device
and we have a valid connector
The second usage is replaced with drm_panel.dev
- this makes drivers more consistent in their dev argument
used for dev_err() and friends
With these replacements there are no more uses of drm_panel.drm,
so it is removed from struct drm_panel.
With this change drm_panel_attach() and drm_panel_detach()
no longer have any use as they are empty functions.
v2:
- editorial correction in changelog (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
Sam Ravnborg [Sat, 7 Dec 2019 14:03:33 +0000 (15:03 +0100)]
drm/panel: add drm_connector argument to get_modes()
Today the bridge creates the drm_connector, but that is planned
to be moved to the display drivers.
To facilitate this, update drm_panel_funcs.get_modes() to
take drm_connector as an argument.
All panel drivers implementing get_modes() are updated.
v2:
- drop accidental change (Laurent)
- update docs for get_modes (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-6-sam@ravnborg.org
Sam Ravnborg [Sat, 7 Dec 2019 14:03:32 +0000 (15:03 +0100)]
drm: get drm_bridge_panel connector via helper
The drm_connector created by drm_panel_bridge was accessed
via drm_panel.connector.
Avoid the detour around drm_panel by providing a simple get method.
This avoids direct access to the connector field in drm_panel in
the two users.
The change is done in preparation for removal of drm_panel.connector.
Update pl111 and tve200 to use the new helper.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Eric Anholt <eric@anholt.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-5-sam@ravnborg.org
Sam Ravnborg [Sat, 7 Dec 2019 14:03:30 +0000 (15:03 +0100)]
drm/panel: add backlight support
Panels often support backlight as specified in a device tree.
Update the drm_panel infrastructure to support this to
simplify the drivers.
With this the panel driver just needs to add the following to the
probe() function:
err = drm_panel_of_backlight(panel);
if (err)
return err;
Then drm_panel will handle all the rest.
There is one caveat with the backlight support.
If drm_panel_(enable|disable) are called multiple times
in a row then backlight_(enable|disable) will be called multiple times.
The above will happen when a panel drivers unconditionally
calls drm_panel_disable() in their shutdown() function,
whan the panel is already disabled and then shutdown() is called.
Reading the backlight code it seems safe to call
the backlight_(enable|disable) several times.
v3:
- Improve comments, fix grammar (Laurent)
- Do not fail in drm_panel_of_backlight() if no DT support (Laurent)
- Log if backlight_(enable|disable) fails (Laurent)
- Improve drm_panel_of_backlight() docs
- Updated changelog with backlight analysis (triggered by Laurent)
v2:
- Drop test of CONFIG_DRM_PANEL in header-file (Laurent)
- do not enable backlight if ->enable() returns an error
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-3-sam@ravnborg.org
Sam Ravnborg [Sat, 7 Dec 2019 14:03:29 +0000 (15:03 +0100)]
drm/drm_panel: no error when no callback
The callbacks in drm_panel_funcs are optional, so do not
return an error just because no callback is assigned.
v2:
- Document what functions in drm_panel_funcs are optional (Laurent)
- Return -EOPNOTSUPP if get_modes() is not assigned (Laurent)
(Sam: -EOPNOTSUPP seems to best error code in this situation)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-2-sam@ravnborg.org
Boris Brezillon [Tue, 3 Dec 2019 14:15:08 +0000 (15:15 +0100)]
drm/bridge: Make the bridge chain a double-linked list
So that each element in the chain can easily access its predecessor.
This will be needed to support bus format negotiation between elements
of the bridge chain.
Boris Brezillon [Tue, 3 Dec 2019 14:15:07 +0000 (15:15 +0100)]
drm: Stop accessing encoder->bridge directly
We are about to replace the single-linked bridge list by a double-linked
one based on list.h, leading to the suppression of the encoder->bridge
field. But before we can do that we must provide a
drm_bridge_chain_get_first_bridge() bridge helper and patch all drivers
and core helpers to use it instead of directly accessing encoder->bridge.
Note that we still have 2 drivers (VC4 and Exynos) manipulating the
encoder->bridge field directly because they need to cut the bridge chain
in order to control the enable/disable sequence. This is definitely
not something we want to encourage, so let's keep those 2 oddities
around until we find a better solution.
And use it in drivers accessing the bridge->next field directly.
This is part of our attempt to make the bridge chain a double-linked list
based on the generic list helpers.
Boris Brezillon [Tue, 3 Dec 2019 14:15:05 +0000 (15:15 +0100)]
drm/bridge: Rename bridge helpers targeting a bridge chain
Change the prefix of bridge helpers targeting a bridge chain from
drm_bridge_ to drm_bridge_chain_ to better reflect the fact that
the operation will happen on all elements of chain, starting at the
bridge passed in argument.
Wayne Lin [Thu, 5 Dec 2019 09:00:43 +0000 (17:00 +0800)]
drm/dp_mst: Remove VCPI while disabling topology mgr
[Why]
This patch is trying to address the issue observed when hotplug DP
daisy chain monitors.
e.g.
src-mstb-mstb-sst -> src (unplug) mstb-mstb-sst -> src-mstb-mstb-sst
(plug in again)
Once unplug a DP MST capable device, driver will call
drm_dp_mst_topology_mgr_set_mst() to disable MST. In this function,
it cleans data of topology manager while disabling mst_state. However,
it doesn't clean up the proposed_vcpis of topology manager.
If proposed_vcpi is not reset, once plug in MST daisy chain monitors
later, code will fail at checking port validation while trying to
allocate payloads.
When MST capable device is plugged in again and try to allocate
payloads by calling drm_dp_update_payload_part1(), this
function will iterate over all proposed virtual channels to see if
any proposed VCPI's num_slots is greater than 0. If any proposed
VCPI's num_slots is greater than 0 and the port which the
specific virtual channel directed to is not in the topology, code then
fails at the port validation. Since there are stale VCPI allocations
from the previous topology enablement in proposed_vcpi[], code will fail
at port validation and reurn EINVAL.
[How]
Clean up the data of stale proposed_vcpi[] and reset mgr->proposed_vcpis
to NULL while disabling mst in drm_dp_mst_topology_mgr_set_mst().
Changes since v1:
*Add on more details in commit message to describe the issue which the
patch is trying to fix
drm/udl: Remove field lost_pixels from struct udl_device
The field lost_pixels in struct udl_device was supposed to signal an
error during USB transfers of the framebuffer data. The driver would
have to schedule a re-transfer at a later point. This code was never
implemented. Remove lost_pixels and return regular error codes instead.
drm/udl: Begin/end access to imported buffers in damage-handler
The damage-handler code now invokes dma_buf_{begin,end}_access()
for imported buffers. These calls were missing from the page-flip
and modesetting code paths. The patch also fixes an bug in the
original where an error code was overwritten by the result of
dma_buf_end_cpu_access().
v2:
* only return an error code from dma_buf_end_cpu_access() if
no other error code has been set before
Gerd Hoffmann [Wed, 27 Nov 2019 09:25:23 +0000 (10:25 +0100)]
drm: share address space for dma bufs
Use the shared address space of the drm device (see drm_open() in
drm_file.c) for dma-bufs too. That removes a difference betweem drm
device mmap vmas and dma-buf mmap vmas and fixes corner cases like
dropping ptes (using madvise(DONTNEED) for example) not working
properly.
Also remove amdgpu driver's private dmabuf update. It is not needed
any more now that we are doing this for everybody.
Gerd Hoffmann [Wed, 27 Nov 2019 09:25:22 +0000 (10:25 +0100)]
drm: call drm_gem_object_funcs.mmap with fake offset
The fake offset is going to stay, so change the calling convention for
drm_gem_object_funcs.mmap to include the fake offset. Update all users
accordingly.
Note that this reverts 83b8a6f242ea ("drm/gem: Fix mmap fake offset
handling for drm_gem_object_funcs.mmap") and on top then adds the fake
offset to drm_gem_prime_mmap to make sure all paths leading to
obj->funcs->mmap are consistent.
v3: move fake-offset tweak in drm_gem_prime_mmap() so we have this code
only once in the function (Rob Herring).
Fixes: 83b8a6f242ea ("drm/gem: Fix mmap fake offset handling for drm_gem_object_funcs.mmap") Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Rob Herring <robh@kernel.org> Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20191127092523.5620-2-kraxel@redhat.com
FEC is supported since DP 1.4, and it was expanded for LT-tunable in DP
1.4a. This commit adds the address registers for
FEC_ERROR_COUNT_PHY_REPEATER1 and FEC_CAPABILITY_PHY_REPEATER1.
Cc: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Reviewed-by: Zhan Liu <zhan.liu@amd.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191205135856.232784-1-Rodrigo.Siqueira@amd.com
Rodrigo Siqueira [Mon, 21 Oct 2019 15:03:53 +0000 (15:03 +0000)]
drm: Fix DSC throughput mode 0 mask definition
Commit d7cd0e053b17 introduced a change at DP_DSC_THROUGHPUT_MODE_0_170
which is not aligned with the spec. This commit replace 15 << 4 by 15 <<
0 for DP_DSC_THROUGHPUT_MODE_0_170 in order to make it follow the
specification.
Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Nikola Cornij <nikola.cornij@amd.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191021150345.igdye4kv35nsk4ox@outlook.office365.com
drm/vkms: Fix typo and preposion in function documentation
Fix typo in word 'blend' and in the word 'destination' and change
preposition 'at' to 'of' in function 'blend' documentation.
And change the task introduction word 'Todo' for the word all in uppercase
- 'TODO'. With the TODO word all in uppercase (as it's the standard) it's
easier to find the tasks that have to be done throughout the code.
Changes since V3:
Rodrigo:
- Merge the patch series into a single patch since it contains one single
logical change
Changes since V2:
- Add fix typo in word 'destination'
- Add change of the preposition
- Fix the name of the function in log message
- Add the change in word 'Todo'
drm/doc: Add VKMS module description and use to "Testing and Validation"
Add a description on VKMS module and the cases in which it should be used.
There's a brief explanation on how to set it and use it in a VM, along with
an example of running an igt-test.
Changes since V3:
Rodrigo:
- Change the log message to imperative
- Fix some bad spelling/writing
- Add a blank line before enumeration
Changes since V2:
Andre:
- Avoid repetition of words in the same sentence;
- Make the explanation on 'setting the kernel' shorter, eliminate the
'make menuconfig' command;
- Add tab on enumeration to have one line per item;
- Clarify from each machine igt-tests commands should be ran on.
Sean Paul [Thu, 29 Aug 2019 00:09:44 +0000 (20:09 -0400)]
drm/dp_mst: Clear all payload id tables downstream when initializing
It seems that on certain MST hubs, namely the CableMatters USB-C 2x DP
hub, using the DP_PAYLOAD_ALLOCATE_SET and DP_PAYLOAD_TABLE_UPDATE_STATUS
register ranges to clear any pre-existing payload allocations on the hub isn't
always enough to reset things if the source device has been reset unexpectedly.
Or at least, that's the current running theory. The precise behavior appears to
be that when the source device gets reset unexpectedly, the hub begins reporting
an available_pbn value of 0 for all of its ports. This is a bit inconsistent
with the our theory, since this seems to happen even if previously set PBN
allocations should have resulted in a non-zero available_pbn value. So, it's
possible that something else may be going on here.
Strangely though, sending a CLEAR_PAYLOAD_ID_TABLE broadcast request when
initializing the MST topology seems to bring things into working order and make
available_pbn work again. Since this is a pretty safe solution, let's go ahead
and implement it.
Changes since v1:
* Change indenting on drm_dp_send_clear_payload_id_table() prototype
* Remove some braces in drm_dp_send_clear_payload_id_table()
* Reorganize some variable declarations in drm_dp_send_clear_payload_id_table()
* Don't forget to handle DP_CLEAR_PAYLOAD_ID_TABLE in
drm_dp_sideband_parse_reply()
* Move drm_dp_send_clear_payload_id_table() call into
drm_dp_mst_link_probe_work(), since we can't send sideband messages
while under lock in drm_dp_mst_topology_mgr_set_mst()
* Change commit message
projects / mirror_ubuntu-jammy-kernel.git / log