This patch add the missing dma_unmap().
Which solved the critical issue of system freeze on heavy load.
Michal Miroslaw's rejected patch:
[PATCH v2 10/46] net: jme: convert to generic DMA API
Pointed out the issue also, thank you Michal.
But the fix was incorrect. It would unmap needed address
when low memory.
Got lots of feedback from End user and Gentoo Bugzilla.
https://bugs.gentoo.org/show_bug.cgi?id=373109
Thank you all. :)
Cc: stable@kernel.org Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohua Li [Tue, 19 Jul 2011 15:49:26 +0000 (08:49 -0700)]
vmscan: fix a livelock in kswapd
I'm running a workload which triggers a lot of swap in a machine with 4
nodes. After I kill the workload, I found a kswapd livelock. Sometimes
kswapd3 or kswapd2 are keeping running and I can't access filesystem,
but most memory is free.
This looks like a regression since commit 08951e545918c159 ("mm: vmscan:
correct check for kswapd sleeping in sleeping_prematurely").
Node 2 and 3 have only ZONE_NORMAL, but balance_pgdat() will return 0
for classzone_idx. The reason is end_zone in balance_pgdat() is 0 by
default, if all zones have watermark ok, end_zone will keep 0.
Later sleeping_prematurely() always returns true. Because this is an
order 3 wakeup, and if classzone_idx is 0, both balanced_pages and
present_pages in pgdat_balanced() are 0. We add a special case here.
If a zone has no page, we think it's balanced. This fixes the livelock.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A value larger than INT_MAX cannot be written to the debugfs file created
by debugfs_create_u64 or debugfs_create_x64 on 32bit machine. Because
simple_attr_write() uses simple_strtol() for the conversion.
To fix this, use simple_strtoll() instead.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't update *inode in __follow_mount_rcu() until we'd verified that
there is mountpoint there. Kudos to Hugh Dickins for catching that
one in the first place and eventually figuring out the solution (and
catching a braino in the earlier version of patch).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pppoe: Must flush connections when MAC address changes too.
include/linux/sdla.h: remove the prototype of sdla()
tulip: dmfe: Remove old log spamming pr_debugs
Al Viro [Mon, 18 Jul 2011 17:50:40 +0000 (13:50 -0400)]
Fix cifs_get_root()
Add missing ->i_mutex, convert to lookup_one_len() instead of
(broken) open-coded analog, cope with getting something like
a//b as relative pathname. Simplify the hell out of it, while
we are there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jeff Layton <jlayton@redhat.com>
Joe Perches [Mon, 18 Jul 2011 17:44:44 +0000 (10:44 -0700)]
tulip: dmfe: Remove old log spamming pr_debugs
Commit 726b65ad444d ("tulip: Convert uses of KERN_DEBUG") enabled
some old previously inactive uses of pr_debug converted by
commit dde7c8ef1679 ("tulip/dmfe.c: Use dev_<level> and pr_<level>").
Remove these pr_debugs.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
si4713-i2c: avoid potential buffer overflow on si4713
While compiling it with Fedora 15, I noticed this issue:
inlined from ‘si4713_write_econtrol_string’ at drivers/media/radio/si4713-i2c.c:1065:24:
arch/x86/include/asm/uaccess_32.h:211:26: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct
Al Viro [Mon, 18 Jul 2011 02:27:22 +0000 (22:27 -0400)]
hppfs_lookup(): don't open-code lookup_one_len()
... and it's getting it wrong, too - missing ->d_revalidate() calls when
it's dealing with filesystem (procfs) that has non-trivial ->d_revalidate()...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] update cifs to version 1.74
[CIFS] update limit for snprintf in cifs_construct_tcon
cifs: Fix signing failure when server mandates signing for NTLMSSP
Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: DMA Cleanup as per sparse
ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chip
spi_sync call uses its spi_message parameter to keep completion information,
using a drvdata structure is not thread-safe. Use a mutex to prevent
multiple access to shared driver data.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Cyril Hrubis <metan@ucw.cz> Tested-by: Stanislav Brabec <utx@penguin.cz> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org
Jean Delvare [Sun, 17 Jul 2011 16:39:19 +0000 (18:39 +0200)]
hwmon: (it87) Fix label group removal
A copy-and-paste error caused it87_attributes_vid to be referenced
where it87_attributes_label should be. Thankfully the group is only
used for attribute removal, not attribute creation, so the effects of
this bug are limited, but let's fix it still.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Randy Dunlap [Sat, 16 Jul 2011 19:25:49 +0000 (12:25 -0700)]
watchdog: hpwdt depends on PCI
hpwdt is a PCI driver so it should depend on PCI.
Fixes these build errors:
drivers/watchdog/hpwdt.c:762: error: implicit declaration of function 'pci_iomap'
drivers/watchdog/hpwdt.c:762: warning: assignment makes pointer from integer without a cast
drivers/watchdog/hpwdt.c:797: error: implicit declaration of function 'pci_iounmap'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Mark Brown [Thu, 14 Jul 2011 09:21:37 +0000 (18:21 +0900)]
ASoC: Correct WM8994 MICBIAS supply widget hookup
The WM8994 and WM8958 series of devices have two MICBIAS supplies rather
than one, the current widget actually manages the microphone detection
control register bit (which is managed separately by the relevant API).
Fix this, hooking the relevant supplies up to the MICBIAS1 and MICBIAS2
widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Al Viro [Sun, 17 Jul 2011 03:37:20 +0000 (23:37 -0400)]
cifs: build_path_from_dentry() race fix
deal with d_move() races properly; rename_lock read-retry loop,
rcu_read_lock() held while walking to root, d_lock held over
subtraction from namelen and copying the component to stabilize
->d_name.
Will Simoneau [Sat, 16 Jul 2011 17:45:12 +0000 (10:45 -0700)]
sparc: sun4m SMP: fix wrong shift instruction in IPI handler
This shift instruction appears to be shifting in the wrong direction.
Without this change, my SparcStation-20MP hangs just after bringing up
the second CPU:
Entering SMP Mode...
Starting CPU 2 at f02b4e90
Brought up 2 CPUs
Total of 2 processors activated (99.52 BogoMIPS).
*** stuck ***
Signed-off-by: Will Simoneau <simoneau@ele.uri.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilia Kolomisnky [Fri, 15 Jul 2011 18:30:21 +0000 (18:30 +0000)]
Bluetooth: Fix crash with incoming L2CAP connections
Another regression fix considering incomming l2cap connections with
defer_setup enabled. In situations when incomming connection is
extracted with l2cap_sock_accept, it's bt_sock info will have
'parent' member zerroed, but 'parent' may be used unconditionally
in l2cap_conn_start() and l2cap_security_cfm() when defer_setup
is enabled.
Backtrace:
[<bf02d5ac>] (l2cap_security_cfm+0x0/0x2ac [bluetooth]) from [<bf01f01c>] (hci_event_pac
ket+0xc2c/0x4aa4 [bluetooth])
[<bf01e3f0>] (hci_event_packet+0x0/0x4aa4 [bluetooth]) from [<bf01a844>] (hci_rx_task+0x
cc/0x27c [bluetooth])
[<bf01a778>] (hci_rx_task+0x0/0x27c [bluetooth]) from [<c008eee4>] (tasklet_action+0xa0/
0x15c)
[<c008ee44>] (tasklet_action+0x0/0x15c) from [<c008f38c>] (__do_softirq+0x98/0x130)
r7:00000101 r6:00000018 r5:00000001 r4:efc46000
[<c008f2f4>] (__do_softirq+0x0/0x130) from [<c008f524>] (do_softirq+0x4c/0x58)
[<c008f4d8>] (do_softirq+0x0/0x58) from [<c008f5e0>] (run_ksoftirqd+0xb0/0x1b4)
r4:efc46000 r3:00000001
[<c008f530>] (run_ksoftirqd+0x0/0x1b4) from [<c009f2a8>] (kthread+0x84/0x8c)
r7:00000000 r6:c008f530 r5:efc47fc4 r4:efc41f08
[<c009f224>] (kthread+0x0/0x8c) from [<c008cc84>] (do_exit+0x0/0x5f0)
Signed-off-by: Ilia Kolomisnky <iliak@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: Fix regression with incoming L2CAP connections
PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that
( probably after the df3c3931e commit ) the l2cap connection
could not be established in case when the "Auth Complete" HCI
event does not arive before the initiator send "Configuration
request", in which case l2cap replies with "Command rejected"
since the channel is still in BT_CONNECT2 state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
Sangwook Lee [Sat, 16 Jul 2011 06:50:19 +0000 (15:50 +0900)]
ARM: SAMSUNG: DMA Cleanup as per sparse
Function declaration differs between file: dma.c and file:dma.h
and SPARSE (Documentation/sparse.txt) gives error messages
All dma channels are members of 'enum dma_ch' and not 'unsigned int'
Please have a look at channel definitions in:
arch/arm/mach-s3c64xx/include/mach/dma.h
arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h
arch/arm/mach-s3c2410/include/mach/dma.h
So all arguments should be of type 'enum dma_ch'
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Olaf Hering [Fri, 15 Jul 2011 21:23:33 +0000 (23:23 +0200)]
watchdog: fix hpwdt Kconfig regression in 3.0-rc
Remove Kconfig regression caused by commit a4616153deae053b29a2b7dd9ec4b2a225accfc5 "watchdog: hpwdt: build hpwdt as
module by default with NMI_DECODING enabled"
With the above change applied, hpwdt will be enabled unconditionally by just
entering the Watchdog subscreen in menuconfig. Since this driver is not
essential to boot any box it should remain disabled until it gets manually
enabled, just like all other drivers.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Cc: Tony Camuso <tcamuso@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
clocksource: convert ARM 32-bit up counting clocksources
broke the build for ixp4xx and made big endian operation impossible.
This commit restores the original behaviour.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
[ Thomas says that we might want to have generic BE accessor functions
to the MMIO clock source, but that hasn't happened yet, so in the
meantime this seems to be the short-term fix for the particular
problem - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sebastian Pöhn [Fri, 15 Jul 2011 23:00:20 +0000 (16:00 -0700)]
gianfar: rx parser
Only let the rx parser be enabled if it is necessary (if VLAN extraction,
IP or TCP checksumming or the rx queue filer are enabled). Otherwise
disable it.
The new routine gfar_check_rx_parser_mode should be run after every
change on this features and will enable/disable the parser as necessary.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Ralf Baechle <ralf@linux-mips.org>
Axel Lin [Sun, 10 Jul 2011 07:45:07 +0000 (15:45 +0800)]
gpio: wm831x: add a missing break in wm831x_gpio_dbg_show
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (adm1275) Fix coefficients per datasheet revision B
hwmon: (pmbus) Use long variables for register to data conversions
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fix loop checks in d_materialise_unique()
Fix ->d_lock locking order in unlazy_walk()
Merge branch 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu:
rcu: Prevent RCU callbacks from executing before scheduler initialized
Peter Zijlstra [Mon, 11 Jul 2011 14:28:50 +0000 (16:28 +0200)]
sched: Fix 32bit race
Commit 3fe1698b7fe0 ("sched: Deal with non-atomic min_vruntime reads
on 32bit") forgot to initialize min_vruntime_copy which could lead to
an infinite while loop in task_waking_fair() under some circumstances
(early boot, lucky timing).
[ This bug was also reported by others that blamed it on the RCU
initialization problems ]
Reported-and-tested-by: Bruno Wolff III <bruno@wolff.to> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
r6040: only disable RX interrupt if napi_schedule_prep is successful
When receiving the first RX interrupt before the internal call
to napi_schedule_prep is successful the RX interrupt gets disabled
and is never enabled again as the poll function never gets executed.
Signed-off-by: Michael Thalmeier <Michael.Thalmeier@sigmatek.at> Signed-off-by: David S. Miller <davem@davemloft.net>
hwmon: (adm1275) Fix coefficients per datasheet revision B
Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
Al Viro [Wed, 13 Jul 2011 01:42:24 +0000 (21:42 -0400)]
fix loop checks in d_materialise_unique()
Both __d_unalias() and __d_materialise_dentry() need loop prevention.
Grab rename_lock in caller, check for loops there...
As a side benefit, we have dentry_lock_for_move() called only under
rename_lock, which seriously reduces deadlock potential of the
execrable "locking order" used for ->d_lock.
Michał Mirosław [Wed, 13 Jul 2011 14:10:29 +0000 (14:10 +0000)]
net: remove NETIF_F_ALL_TX_OFFLOADS
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Wed, 13 Jul 2011 14:10:29 +0000 (14:10 +0000)]
net: sctp: fix checksum marking for outgoing packets
Packets to devices without NETIF_F_SCTP_CSUM (including NETIF_F_NO_CSUM)
should be properly checksummed because the packets can be diverted or
rerouted after construction. This still leaves packets diverted from
NETIF_F_SCTP_CSUM-enabled devices with broken checksums. Fixing this
needs implementing software offload fallback in networking core.
For users of sctp_checksum_disable, skb->ip_summed should be left as
CHECKSUM_NONE and not CHECKSUM_UNNECESSARY as per include/linux/skbuff.h.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Resolve inode eviction and ail list interaction bug
GFS2: Fix race during filesystem mount
GFS2: force a log flush when invalidating the rindex glock
GFS2: Resolve inode eviction and ail list interaction bug
This patch contains a few misc fixes which resolve a recently
reported issue. This patch has been a real team effort and has
received a lot of testing.
The first issue is that the ail lock needs to be held over a few
more operations. The lock thats added into gfs2_releasepage() may
possibly be a candidate for replacing with RCU at some future
point, but at this stage we've gone for the obvious fix.
The second issue is that gfs2_write_inode() can end up calling
a glock recursively when called from gfs2_evict_inode() via the
syncing code, so it needs a guard added.
The third issue is that we either need to not truncate the metadata
pages of inodes which have zero link count, but which we cannot
deallocate due to them still being in use by other nodes, or we need
to ensure that those pages have all made it through the journal and
ail lists first. This patch takes the former approach, but the
latter has also been tested and there is nothing to choose between
them performance-wise. So again, we could revise that decision
in the future.
Also, the inode eviction process is now better documented.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Tested-by: Bob Peterson <rpeterso@redhat.com> Tested-by: Abhijith Das <adas@redhat.com> Reported-by: Barry J. Marson <bmarson@redhat.com> Reported-by: David Teigland <teigland@redhat.com>
Lin Ming [Wed, 1 Jun 2011 15:54:02 +0000 (23:54 +0800)]
ACPI: Fixes device power states array overflow
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com> Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI, APEI, HEST, Detect duplicated hardware error source ID
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes #37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org Signed-off-by: Huang Ying <ying.huang@intel.com> Tested-by: Mathias <janedo.spam@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu> Tested-by: Simon Arlott <simon@fire.lp0.eu> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] dvb_frontend: fix race condition in stopping/starting frontend
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix use of static variable in rpcb_getport_async
NFSv4.1: update nfs4_fattr_bitmap_maxsz
SUNRPC: Fix a race between work-queue and rpc_killall_tasks
pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Philip Rakity [Thu, 7 Jul 2011 16:04:55 +0000 (09:04 -0700)]
mmc: core: Bus width testing needs to handle suspend/resume
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc397ac1a3
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI: Fix lockdep false positives in acpi_power_off()
All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock". Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.
To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock. Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.
This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: Borislav Petkov <bp@alien8.de> Tested-by: Andrea Righi <andrea@betterlinux.com> Reviewed-by: Florian Mickler <florian@mickler.org> Signed-off-by: Len Brown <len.brown@intel.com>
Paul E. McKenney [Sun, 10 Jul 2011 22:57:35 +0000 (15:57 -0700)]
rcu: Prevent RCU callbacks from executing before scheduler initialized
Under some rare but real combinations of configuration parameters, RCU
callbacks are posted during early boot that use kernel facilities that
are not yet initialized. Therefore, when these callbacks are invoked,
hard hangs and crashes ensue. This commit therefore prevents RCU
callbacks from being invoked until after the scheduler is fully up and
running, as in after multiple tasks have been spawned.
It might well turn out that a better approach is to identify the specific
RCU callbacks that are causing this problem, but that discussion will
wait until such time as someone really needs an RCU callback to be invoked
(as opposed to merely registered) during early boot.
Reported-by: julie Sullivan <kernelmail.jms@gmail.com> Reported-by: RKK <kulkarni.ravi4@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Tested-by: julie Sullivan <kernelmail.jms@gmail.com> Tested-by: RKK <kulkarni.ravi4@gmail.com>
Ryusuke Konishi [Sun, 19 Jun 2011 07:56:29 +0000 (16:56 +0900)]
nilfs2: remove resize from unsupported features list
Resize feature was supported by the commit 4e33f9eab07e but it was not
reflected to the list of unsupported features in nilfs2.txt file.
This updates the list to fix discrepancy.
Chris Wilson [Tue, 12 Jul 2011 22:38:18 +0000 (23:38 +0100)]
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Konstantin Belousov <kostikbel@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ralf Baechle [Fri, 24 Jun 2011 13:30:09 +0000 (10:30 -0300)]
[media] MEDIA: Fix non-ISA_DMA_API link failure of sound code
sound/isa/es18xx.c: In function ‘snd_es18xx_playback1_prepare’:
sound/isa/es18xx.c:501:9: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es18xx.c: In function ‘snd_es18xx_playback_pointer’:
sound/isa/es18xx.c:818:3: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/es18xx.o] Error 1
sound/isa/sscape.c: In function ‘upload_dma_data’:
sound/isa/sscape.c:481:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/sscape.o] Error 1
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_prepare’:
sound/isa/ad1816a/ad1816a_lib.c:244:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_pointer’:
sound/isa/ad1816a/ad1816a_lib.c:302:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_free’:
sound/isa/ad1816a/ad1816a_lib.c:544:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/ad1816a/ad1816a_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/ad1816a] Error 2
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_prepare’:
sound/isa/es1688/es1688_lib.c:417:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_pointer’:
sound/isa/es1688/es1688_lib.c:509:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/es1688/es1688_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/es1688] Error 2
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_program’:
sound/isa/gus/gus_dma.c:79:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_done’:
sound/isa/gus/gus_dma.c:177:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_dma.o] Error 1
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_prepare’:
sound/isa/gus/gus_pcm.c:591:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_pointer’:
sound/isa/gus/gus_pcm.c:619:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_pcm.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/gus] Error 2
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_ioctl’:
sound/isa/sb/sb16_csp.c:228:227: error: case label does not reduce to an integer constant
make[3]: *** [sound/isa/sb/sb16_csp.o] Error 1
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_prepare’:
sound/isa/sb/sb16_main.c:276:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_pointer’:
sound/isa/sb/sb16_main.c:456:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb16_main.o] Error 1
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_prepare’:
sound/isa/sb/sb8_main.c:172:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_pointer’:
sound/isa/sb/sb8_main.c:425:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb8_main.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/sb] Error 2
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_prepare’:
sound/isa/wss/wss_lib.c:1025:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_pointer’:
sound/isa/wss/wss_lib.c:1160:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_free’:
sound/isa/wss/wss_lib.c:1695:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/wss/wss_lib.o] Error 1
warning: (RADIO_MIROPCM20) selects SND_ISA which has unmet direct dependencies (SOUND && !M68K && SND && ISA && ISA_DMA_API)
A build with ISA && ISA_DMA && !ISA_DMA_API results in:
CC sound/isa/es18xx.o
CC sound/isa/sscape.o
CC sound/isa/ad1816a/ad1816a_lib.o
CC sound/isa/es1688/es1688_lib.o
CC sound/isa/gus/gus_dma.o
CC sound/isa/gus/gus_pcm.o
CC sound/isa/sb/sb16_csp.o
CC sound/isa/sb/sb16_main.o
CC sound/isa/sb/sb8_main.o
CC sound/isa/wss/wss_lib.o
The root cause for this is hidden in this Kconfig warning:
Adding a dependency on ISA_DMA_API to RADIO_MIROPCM20 fixes these issues.
Al Viro [Wed, 13 Jul 2011 01:40:23 +0000 (21:40 -0400)]
Fix ->d_lock locking order in unlazy_walk()
Make sure that child is still a child of parent before nested locking
of child->d_lock in unlazy_walk(); otherwise we are risking a violation
of locking order and deadlocks.
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable GPU reset on Ivybridge.
drm/i915/dp: manage sink power state if possible
drm/i915/dp: consolidate AUX retry code
drm/i915/dp: remove DPMS mode tracking from DP
drm/i915/dp: try to read receiver capabilities 3 times when detecting
drm/i915/dp: read more receiver capability bits on hotplug
drm/i915/dp: use DP DPCD defines when looking at DPCD values
drm/i915/dp: retry link status read 3 times on failure
Steve French [Tue, 12 Jul 2011 18:24:43 +0000 (18:24 +0000)]
[CIFS] update limit for snprintf in cifs_construct_tcon
In 34c87901e113 "Shrink stack space usage in cifs_construct_tcon" we
change the size of the username name buffer from MAX_USERNAME_SIZE
(256) to 28. This call to snprintf() needs to be updated as well.
Reported by Dan Carpenter.
Reviewed-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: Fix signing failure when server mandates signing for NTLMSSP
When using NTLMSSP authentication mechanism, if server mandates
signing, keep the flags in type 3 messages of the NTLMSSP exchange
same as in type 1 messages (i.e. keep the indicated capabilities same).
Some of the servers such as Samba, expect the flags such as
Negotiate_Key_Exchange in type 3 message of NTLMSSP exchange as well.
Some servers like Windows do not.
https://bugzilla.samba.org/show_bug.cgi?id=8212
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Ben Greear [Tue, 12 Jul 2011 17:27:55 +0000 (10:27 -0700)]
SUNRPC: Fix use of static variable in rpcb_getport_async
Because struct rpcbind_args *map was declared static, if two
threads entered this method at the same time, the values
assigned to map could be sent two two differen tasks.
This could cause all sorts of problems, include use-after-free
and double-free of memory.
Fix this by removing the static declaration so that the map
pointer is on the stack.
Signed-off-by: Ben Greear <greearb@candelatech.com> Cc: stable@kernel.org Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chris Wilson [Tue, 12 Jul 2011 17:03:29 +0000 (18:03 +0100)]
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jul 2011 20:12:17 +0000 (13:12 -0700)]
drm/i915: Clean up i915_driver_load failure path
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com> Tested-by: Lin Ming <ming.m.lin@intel.com>
hwmon: (pmbus) Use long variables for register to data conversions
Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Michal Marek [Tue, 12 Jul 2011 09:54:48 +0000 (11:54 +0200)]
kbuild: Do not write to builddir in modules_install
Let depmod.sh create a temporary directory in /tmp instead of writing to
the build directory as root. The mktemp utility should be available on
any recent system (and there is already scripts/gen_initramfs_list.sh
relying on it).
Reported-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Michal Marek <mmarek@suse.cz>
Commit 7416401 ("arm: davinci: Fix fallout from generic irq chip
conversion") introduced a bug, causing low level interrupt handlers to
get a bogus irq number as an argument. The gpio irq handler falsely
assumes that the handler data is the irq base number and that is no
longer true.
Set the irq handler data to be a pointer to the corresponding gpio
controller. The chained irq handler can then use it to extract both the
irq base number and the gpio registers structure.
Signed-off-by: Ido Yariv <ido@wizery.com> CC: Thomas Gleixner <tglx@linutronix.de>
[nsekhar@ti.com: renamed "ctl" to "d", simplified indexing logic for chips and
took care of odd bank handling in irq handler] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is a potential race during filesystem mounting which has recently
been reported. It occurs when the userland gfs_controld is able to
process requests fast enough that it tries to use the sysfs interface
before the lock module is properly initialised. This is a pretty
unusual case as normally the lock module initialisation is very quick
compared with gfs_controld.
This patch adds an interruptible completion which is used to ensure that
userland will wait for the initialisation of the lock module to
complete.
There are other potential solutions to this problem, but this is the
quickest at this stage and has been tested both with and without
mount.gfs2 present in the system.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Reported-by: David Booher <dbooher@adams.net>
GFS2: force a log flush when invalidating the rindex glock
Right now, there is nothing that forces the log to get flushed when a node
drops its rindex glock so that another node can grow the filesystem. If the
log doesn't get flushed, GFS2 can corrupt the sd_log_le_rg list in the
following way.
A node puts an rgd on the list in rg_lo_add(), and then the rindex glock is
dropped so the other node can grow the filesystem. When the node reacquires the
rindex glock, that rgd gets deleted in clear_rgrpdi() before ever being
removed from the list by gfs2_log_flush().
This code simply forces a log flush when the rindex glock is invalidated,
solving the problem.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
projects / mirror_ubuntu-disco-kernel.git / log