openvswitch: avoid deferred execution of recirc actions
The ovs kernel data path currently defers the execution of all
recirc actions until stack utilization is at a minimum.
This is too limiting for some packet forwarding scenarios due to
the small size of the deferred action FIFO (10 entries). For
example, broadcast traffic sent out more than 10 ports with
recirculation results in packet drops when the deferred action
FIFO becomes full, as reported here:
Since the current recursion depth is available (it is already tracked
by the exec_actions_level pcpu variable), we can use it to determine
whether to execute recirculation actions immediately (safe when
recursion depth is low) or defer execution until more stack space is
available.
With this change, the deferred action fifo size becomes a non-issue
for currently failing scenarios because it is no longer used when
there are three or fewer recursions through ovs_execute_actions().
Suggested-by: Pravin Shelar <pshelar@ovn.org> Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 15 Sep 2016 12:28:23 +0000 (15:28 +0300)]
net/sched: cls_flower: Remove an unused field from the filter key structure
Commit c3f8324188fa "net: Add full IPv6 addresses to flow_keys" added an
unused instance of struct flow_dissector_key_addrs into struct fl_flow_key,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Hadar Hen Zion <hadarh@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 15 Sep 2016 12:28:22 +0000 (15:28 +0300)]
net/sched: cls_flower: Support masking for matching on tcp/udp ports
Add the definitions for src/dst udp/tcp port masks and use
them when setting && dumping the relevant keys.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9ee7b683ea63 we moved the enablement of msi interrupts earlier in
alx_init_intr. If there is an error in alx_alloc_rings, __alx_open returns
with an error but msi (or msi-x) interrupts stays enabled. Add a new error
label to disable msi (or msi-x) interrupts.
Fixes: 9ee7b683ea63 ("alx: refactor msi enablement and disablement") Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe
to:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15
Also try to do a MAC address swap with pedit or worse
try to debug a policy with destination mac, source mac and
etherype. Then make few rules out of those and you'll get my point.
In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.
The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesnt get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac). And at times
when flipping back the packet a swap of the MAC addresses is needed.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 12 Sep 2016 21:38:43 +0000 (23:38 +0200)]
bpf: use skb_at_tc_ingress helper in tcf_bpf
We have a small skb_at_tc_ingress() helper for testing for ingress, so
make use of it. cls_bpf already uses it and so should act_bpf.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 12 Sep 2016 21:38:42 +0000 (23:38 +0200)]
bpf: drop unnecessary test in cls_bpf_classify and tcf_bpf
The skb_mac_header_was_set() test in cls_bpf's and act_bpf's fast-path is
actually unnecessary and can be removed altogether. This was added by
commit a166151cbe33 ("bpf: fix bpf helpers to use skb->mac_header relative
offsets"), which was later on improved by 3431205e0397 ("bpf: make programs
see skb->data == L2 for ingress and egress"). We're always guaranteed to
have valid mac header at the time we invoke cls_bpf_classify() or tcf_bpf().
Reason is that since 6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
we do skb_reset_mac_header() in __dev_queue_xmit() before we could call
into sch_handle_egress() or any subsequent enqueue. sch_handle_ingress()
always sees a valid mac header as well (things like skb_reset_mac_len()
would badly fail otherwise). Thus, drop the unnecessary test in classifier
and action case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rcu_read_lock protection from tunnel_key_dump and use
rtnl_dereference, dump operation is protected by rtnl lock.
Also, remove rcu_read_lock from tunnel_key_release and use
rcu_dereference_protected.
Both operations are running exclusively and a writer couldn't modify
t->params while those functions are executed.
Fixes: 54d94fd89d90 ('net/sched: Introduce act_tunnel_key') Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 12 Sep 2016 12:04:57 +0000 (13:04 +0100)]
test_bpf: fix the dummy skb after dissector changes
Commit d5709f7ab776 ("flow_dissector: For stripped vlan, get vlan
info from skb->vlan_tci") made flow dissector look at vlan_proto
when vlan is present. Since test_bpf sets skb->vlan_tci to ~0
(including VLAN_TAG_PRESENT) we have to populate skb->vlan_proto.
Fixes false negative on test #24:
test_bpf: #24 LD_PAYLOAD_OFF jited:0 175 ret 0 != 42 FAIL (1 times)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Sep 2016 16:16:44 +0000 (12:16 -0400)]
Merge branch 'mlxsw-ethtool'
Jiri Pirko says:
====================
mlxsw: ethtool enhancements
Ido says:
Patches 1-4 do some minor cleanup in current ethtool ops. Patch 5
replace legacy {get,set}_settings callbacks with
{get,set}_link_ksettings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Report port type according to operational speed
In case port isn't operational we shouldn't report the port type, but
instead return PORT_OTHER. This is consistent with most other drivers
that return PORT_OTHER when media type can't be determined.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Report link partner's advertised speeds
If autonegotiation was performed successfully, then we should report the
link partner's advertised speeds instead of the operational speed of the
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 11 Sep 2016 15:54:03 +0000 (17:54 +0200)]
net: ethernet: apm: xgene: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: macb: fix missing unlock on error in macb_start_xmit()
Fix missing unlock before return from function macb_start_xmit()
in the error handling case.
Fixes: 007e4ba3ee13 ("net: macb: initialize checksum when using
checksum offloading") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 8 Sep 2016 16:50:43 +0000 (12:50 -0400)]
net: bridge: add helper to call /sbin/bridge-stp
If /sbin/bridge-stp is available on the system, bridge tries to execute
it instead of the kernel implementation when starting/stopping STP.
If anything goes wrong with /sbin/bridge-stp, bridge silently falls back
to kernel STP, making hard to debug userspace STP.
This patch adds a br_stp_call_user helper to start/stop userspace STP
and debug errors from the program: abnormal exit status is stored in the
lower byte and normal exit status is stored in higher byte.
Below is a simple example on a kernel with dynamic debug enabled:
# ln -s /bin/false /sbin/bridge-stp
# brctl stp br0 on
br0: failed to start userspace STP (256)
# dmesg
br0: /sbin/bridge-stp exited with code 1
br0: failed to start userspace STP (256)
br0: using kernel STP
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: use IS_ENABLED() instead of checking for built-in or module
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sis900: use IS_ENABLED() instead of checking for built-in or module
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Daniele Venzano <venza@brownhat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sfc: use IS_ENABLED() instead of checking for built-in or module
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ethernet: amd: use IS_ENABLED() instead of checking for built-in or module
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly small sets of driver fixes scattered all over the place.
1) Mediatek driver fixes from Sean Wang. Forward port not written
correctly during TX map, missed handling of EPROBE_DEFER, and
mistaken use of put_page() instead of skb_free_frag().
2) Fix socket double-free in KCM code, from WANG Cong.
3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for
using the dcbx buffers before initializing them.
4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for
double fib removals and an error handling fix in
mlxsw_sp_module_init().
5) Fix kernel panic when enabling LLDP in i40e driver, from Dave
Ertman.
6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham.
7) TCP's rcv_wup not initialized properly when using fastopen, from
Neal Cardwell.
8) Don't use uninitialized flow keys in flow dissector, from Gao
Feng.
9) Use after free in l2tp module unload, from Sabrina Dubroca.
10) Fix interrupt registry ordering issues in smsc911x driver, from
Jeremy Linton.
11) Fix crashes in bonding having to do with enslaving and rx_handler,
from Mahesh Bandewar.
12) AF_UNIX deadlock fixes from Linus.
13) In mlx5 driver, don't read skb->xmit_mode after it might have been
freed from the TX reclaim path. From Tariq Toukan.
14) Fix a bug from 2015 in TCP Yeah where the congestion window does
not increase, from Artem Germanov.
15) Don't pad frames on receive in NFP driver, from Jakub Kicinski.
16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo
Leitner.
17) Fix deletion of VRF routes, from Mark Tomlinson.
18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
net/mlx4_en: Fix panic on xmit while port is down
net/mlx4_en: Fixes for DCBX
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
net: ethernet: renesas: sh_eth: add POST registers for rz
drivers: net: phy: mdio-xgene: Add hardware dependency
dwc_eth_qos: do not register semi-initialized device
sctp: identify chunks that need to be fragmented at IP level
mlxsw: spectrum: Set port type before setting its address
mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init
nfp: don't pad frames on receive
nfp: drop support for old firmware ABIs
nfp: remove linux/version.h includes
tcp: cwnd does not increase in TCP YeAH
net/mlx5e: Fix parsing of vlan packets when updating lro header
net/mlx5e: Fix global PFC counters replication
net/mlx5e: Prevent casting overflow
net/mlx5e: Move an_disable_cap bit to a new position
net/mlx5e: Fix xmit_more counter race issue
tcp: fastopen: avoid negative sk_forward_alloc
...
When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.
Fixes: 63a664b7e92b ("net/mlx4_en: fix tx_dropped bug") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Heib [Sun, 11 Sep 2016 07:56:18 +0000 (10:56 +0300)]
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Heib [Sun, 11 Sep 2016 07:56:17 +0000 (10:56 +0300)]
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Rana Shahout <ranas@mellanox.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Get VLAN_PORT_MASK from b53_device
While migrating the bcm_sf2 driver to use b53_common, we left a small
piece untouched where we kept our local copy of the per-port
port_vlan_ctl bitmask value. This value is now maintained by b53_device
so we need to use it instead of our local (and now stale) copy of it.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aa71987472a9 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).
Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.
Cc: Christoph Hellwig <hch@lst.de> Cc: Jay Freyensee <james_p_freyensee@linux.intel.com> Cc: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have
been in linux-next with no reported issues"
* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:core: fix IIO_VAL_FRACTIONAL sign handling
iio: ensure ret is initialized to zero before entering do loop
iio: accel: kxsd9: Fix scaling bug
iio: accel: bmc150: reset chip at init time
iio: fix pressure data output unit in hid-sensor-attributes
tools:iio:iio_generic_buffer: fix trigger-less mode
David S. Miller [Sun, 11 Sep 2016 06:12:54 +0000 (23:12 -0700)]
Merge branch 'vrf-tx-hook'
David Ahern says:
====================
net: Convert vrf to tx hook
The motivation for this series is that ICMP Unreachable - Fragmentation
Needed packets are not handled properly for VRFs. Specifically, the
FIB lookup in __ip_rt_update_pmtu fails so no nexthop exception is
created with the reduced MTU. As a result connections stall if packets
larger than the smallest MTU in the path are generated.
While investigating that problem I also noticed that the MSS for all
connections in a VRF is based on the VRF device's MTU and not the
route the packets ultimately go through. VRF currently uses a dst
to direct packets to the device. The first FIB lookup returns this dst
and then the lookup in the VRF driver gets the actual output route. A
side effect of this design is that the VRF dst is cached on sockets
and then used for calculations like the MSS.
This series fixes this problem by removing the hook in the FIB lookups
that returns the dst pointing to the VRF device to the VRF and always
doing the actual FIB lookup. This allows the real dst to be used
throughout the stack (for example the MSS). Packets are diverted to
the VRF device on Tx using an l3mdev hook in the output path similar to
to what is done for Rx. The end result is a simpler implementation for
VRF with fewer intrusions into the network stack and symmetrical packet
handling for Rx and Tx paths.
Comparison of netperf performance for a build without l3mdev (best case
performance), the old vrf driver and the VRF driver from this series.
Data are collected using VMs with virtio + vhost. The netperf client
runs in the VM and netserver runs in the host. 1-byte RR tests are done
as these packets exaggerate the performance hit due to the extra lookups
done for l3mdev and VRF.
TCP_RR UDP_RR
IPv4 IPv6 IPv4 IPv6
no l3mdev 29,996 30,601 31,638 24,336
vrf old 27,417 27,626 29,159 24,801
vrf new 28,036 28,372 30,110 24,857
l3mdev, no vrf 29,534 30,465 30,670 24,346
* Transactions per second as reported by netperf
* netperf modified to take a bind-to-device argument -- the -J red option
1. 'no l3mdev' == NET_L3_MASTER_DEV is unset so code is compiled out
2. 'vrf old' == data for existing implementation
3. 'vrf new' == data with this series
4. 'l3mdev, no vrf' == NET_L3_MASTER_DEV is enabled but traffic is not
going through a VRF
About the series
- patch 1 adds the flow update (changing oif or iif to L3 master device
and setting the flag to skip the oif check) to ipv4 and ipv6 paths just
before hitting the rules. This catches all code paths in a single spot.
- patch 2 adds the Tx hook to push the packet to the l3mdev if relevant
- patch 3 adds some checks so the vrf device can act as a vrf-local
loopback. These changes were not needed before since the vrf dst was
returned from the lookup.
- patches 4 and 5 flip the ipv4 and ipv6 stacks to the tx hook leaving
the route lookup to be the real one. The dst flip happens at the
beginning of the L3 output path so the VRFs can have device based
features such as netfilter, tc and tcpdump.
- patches 6-11 remove no longer needed l3mdev code
v2
- properly handle IPv6 link scope addresses
- keep the device xmit path and associated dst which is switched in by
the l3_out hook. packets still need to go through the xmit path in
case the user puts a qdisc on the vrf device and to allow tc rules.
version 1 short circuited the tx handling and only covered netfilter
and tcpdump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 10 Sep 2016 19:09:56 +0000 (12:09 -0700)]
net: vrf: Flip IPv6 output path from FIB lookup hook to out hook
Flip the IPv6 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv6 output processing to
send the packet to the VRF driver on xmit.
Link scope addresses (linklocal and multicast) need special handling:
specifically the oif the flow struct can not be changed because we
want the lookup tied to the enslaved interface. ie., the source address
and the returned route MUST point to the interface scope passed in.
Convert the existing vrf_get_rt6_dst to handle only link scope addresses.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 10 Sep 2016 19:09:55 +0000 (12:09 -0700)]
net: vrf: Flip IPv4 output path from FIB lookup hook to out hook
Flip the IPv4 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv4 output processing to
send the packet to the VRF driver on xmit.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 10 Sep 2016 19:09:53 +0000 (12:09 -0700)]
net: l3mdev: Add hook to output path
This patch adds the infrastructure to the output path to pass an skb
to an l3mdev device if it has a hook registered. This is the Tx parallel
to l3mdev_ip{6}_rcv in the receive path and is the basis for removing
the existing hook that returns the vrf dst on the fib lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 10 Sep 2016 19:09:52 +0000 (12:09 -0700)]
net: flow: Add l3mdev flow update
Add l3mdev hook to set FLOWI_FLAG_SKIP_NH_OIF flag and update oif/iif
in flow struct if its oif or iif points to a device enslaved to an L3
Master device. Only 1 needs to be converted to match the l3mdev FIB
rule. This moves the flow adjustment for l3mdev to a single point
catching all lookups. It is redundant for existing hooks (those are
removed in later patches) but is needed for missed lookups such as
PMTU updates.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 08:21:15 +0000 (10:21 +0200)]
ATM-ZeitNet: Replace one kzalloc() call by kcalloc()
* The script "checkpatch.pl" can point information out like the following.
WARNING: Prefer kcalloc over kzalloc with multiply
Thus fix the affected source code place.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
* Delete the local variable "size" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 08:07:38 +0000 (10:07 +0200)]
ATM-ZeitNet: Improve a size determination in zatm_open()
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 07:55:53 +0000 (09:55 +0200)]
ATM-ZeitNet: Use kmalloc_array() in start_tx()
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 06:56:03 +0000 (08:56 +0200)]
ATM-nicstar: Refactor a dev_alloc_skb() call in dequeue_rx()
The script "checkpatch.pl" can point out that assignments should usually
not be performed within condition checks.
Thus move an assignment for a local variable to a separate statement
in this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 06:48:17 +0000 (08:48 +0200)]
ATM-nicstar: Refactor a kmalloc() call in ns_init_card()
* The script "checkpatch.pl" can point out that assignments should usually
not be performed within condition checks.
Thus move an assignment for a local variable to a separate statement
in this function.
* Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 06:30:09 +0000 (08:30 +0200)]
ATM-nicstar: Improve another size determination in ns_init_card()
Replace the specification of a data structure by a reference for a field
in a local variable as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 06:18:10 +0000 (08:18 +0200)]
ATM-nicstar: Improve another size determination in get_scq()
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sat, 10 Sep 2016 06:02:06 +0000 (08:02 +0200)]
ATM-nicstar: Use kmalloc_array() in get_scq()
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 9 Sep 2016 21:22:45 +0000 (14:22 -0700)]
tcp: better use ooo_last_skb in tcp_data_queue_ofo()
Willem noticed that we could avoid an rbtree lookup if the
the attempt to coalesce incoming skb to the last skb failed
for some reason.
Since most ooo additions are at the tail, this is definitely
worth adding a test and fast path.
Suggested-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yaogong Wang <wygivan@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace tries to create datapaths and the module is not loaded,
it will simply fail. With this patch, the module will be automatically
loaded.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Mohamad improves the driver load/unload flows
to seamlessly handle pci errors and device internal errors recovery
reset flows.
Current pci and internal error handling is too heavy and is done
with a full restart of the driver by unregistering mlx5 interfaces
(mlx5e netedevs and mlx5_ib) which will cause losing all the current
interfaces and mlx5 core configurations.
To improve this, we add new callback functions of mlx5 interface
object (attach/detach) to be called upon reset flows when errors are
detected rather than calling register and unregister interfaces.
On their side, interfaces such as (mlx5e and mlx5_ib) can choose to implement
those callback, if not, the old heavy reset will be called for that interface.
For non-interface mlx5 modules such as sriov and eswitch, we refactored
and reorganized the code in a way that the software state objects are created
only once on driver load. Those software state objects are kept upon reset recovery
flows and only freed once on driver unload. On seamless soft reset flows, only
hardware resources are released on stop and re-allocated on start according to the
current soft state.
In this series only mlx5e interface implements attach/detach callbacks
so that the netdevice will be kept alive on reset. On detach only hardware resources
are released and the netdevice will be marked as detached to the stack. Once
attached again it will re-allocate the hardware resources according to the current
netdevice state, and all the configurations and the software state will be kept or restored
after recovery.
Note: I will be out of office all next week, in case of any updates
or V2 is required, Tariq will post the new series, I hope it is ok.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide the exposed (external) mlx5_dev_list and mlx5_intf_mutex and expose
an organized modular API to manage and manipulate mlx5 devices list.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Restore vlan filter after seamless reset
When detaching the mlx5e interface clear all the vlans rules from the
vlan flow table.
When attaching it back restore all the active vlans rules to the HW.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to support seamless and lightweight PCI/Internal error recovery.
Implement the attach/detach interface callbacks.
In attach callback we only allocate HW resources.
In detach callback we only deallocate HW resources.
All SW/kernel objects initialzing/destroying is kept in add/remove
callbacks.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Implement vports admin state backup/restore
Save the user configuration in the vport sturct.
Restore saved old configuration upon vport enable.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Align sriov/eswitch modules with the new load/unload flow.
Init/cleanup sriov/eswitch in the core software context init/cleanup
flows.
Attach/detach sriov/eswitch in the core load/unload flows.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for lightweight and modular internal/pci error handling.
Implement eswitch attach function which allocates/starts hw related
resources.
Implement eswitch detach function which releases/stops hw related
resources.
Init/cleanup function only handle eswitch software context allocation
and destruction.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for lightweight and modular internal/pci error handling.
Implement sriov attach function which enables pre-saved number of vfs on
the device side.
Implement sriov detach function which disable the current vfs on the
device side.
Init/cleanup function only handles sriov software context allocation and
destruction.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Split the load/unload flow into hardware and software flows
Gather all software context creating/destroying in one function and call
it once in the first load and in the last unload.
load/unload functions will now receive indication if we need to
create/destroy the software contexts.
In internal/pci error do the unload/load flows without releasing the
software objects.
In this way we perserve the sw core state and it help us restoring old
driver state after PCI error/shutdown.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Introduce attach/detach to interface API
Add attach/detach callbacks to interface API.
This is crucial for implementing seamless reset flow which releases the
hardware and it's resources upon detach while keeping software
structures and state (e.g netdev) then reset and reallocate the hardware
needed resources upon attach.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and makes it look modular and symmetric.
Split sriov enable/disable to two levels: device level and pci level.
When user enable/disable sriov (via sriov_configure driver callback) we
will enable/disable both device and pci sriov.
When driver load/unload we will enable/disable (on demand) only device
sriov while keeping the PCI sriov enabled for next driver load.
On internal/pci error, VFs will be kept enabled on PCI and the reset
is done only in device level.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Skip waiting for vf pages in internal error
In case of device in internal error state there is no need to wait for
vf pages since they will be reclaimed manually later in the unload flow.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: use IS_ENABLED() instead of checking for built-in or module
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log