Pointers should be cast with uintptr_t instead of integer. This fixes
warning when compile testing on ARM64:
drivers/clk/socfpga/clk-gate.c: In function ‘socfpga_clk_recalc_rate’:
drivers/clk/socfpga/clk-gate.c:102:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fixes: b7cec13f082f ("clk: socfpga: Look for the GPIO_DB_CLK by its offset") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20210314110709.32599-1-krzysztof.kozlowski@canonical.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ce_add_elem() uses different return values to signal a result from
adding an element to the collector. Commit in Fixes: broke the case
where the element being added is not found in the array. Correct that.
The nla_len() is less than or equal to 16. If it's less than 16 then end
of the "gid" buffer is uninitialized.
Fixes: ae43f8286730 ("IB/core: Add IP to GID netlink offload") Link: https://lore.kernel.org/r/20210405074434.264221-1-leon@kernel.org Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ipv6 bit is wrongly set by the below which causes fatal adapter lookup
engine errors for ipv4 connections while destroying a listener. Fix it to
properly check the local address for ipv6.
Fixes: 3408be145a5d ("RDMA/cxgb4: Fix adapter LE hash errors while destroying ipv6 listening server") Link: https://lore.kernel.org/r/20210331135715.30072-1-bharat@chelsio.com Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'struct ovs_zone_limit' has more members than initialized in
ovs_ct_limit_get_default_limit(). The rest of the memory is a random
kernel stack content that ends up being sent to userspace.
Fix that by using designated initializer that will clear all
non-specified fields.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit") Signed-off-by: Ilya Maximets <i.maximets@ovn.org> Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Reviewed-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since commit 14d3d54052539a1e ("perf session: Try to read pipe data from
file") 'perf inject' has started printing "PERFILE2h" when not processing
pipes.
The commit exposed perf to the possiblity that the input is not a pipe
but the 'repipe' parameter gets used. That causes the printing because
perf inject sets 'repipe' to true always.
The 'repipe' parameter of perf_session__new() is used by 2 functions:
- perf_file_header__read_pipe()
- trace_report()
In both cases, the functions copy data to STDOUT_FILENO when 'repipe' is
true.
Fix by setting 'repipe' to true only if the output is a pipe.
Fixes: e558a5bd8b74aff4 ("perf inject: Work with files") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Andrew Vagin <avagin@openvz.org> Link: http://lore.kernel.org/lkml/20210401103605.9000-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Register variables initialized using arithmetic. That leads to
kasan instrumentaton code corrupting the registers contents.
Follow GCC guidlines and use temporary variables for assigning
init values to register variables.
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_unregister(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used. The patch fixes a logical
bug that hasn't been seen in pratice however it is analogus
to the bug fixed in clk_notifier_register().
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_register(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used.
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
Fixes: c1e85c6ce57ef ("net: macb: save/restore the remaining registers and features") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ufshcd_tmc_handler() calls blk_mq_tagset_busy_iter(fn = ufshcd_compl_tm()),
but since blk_mq_tagset_busy_iter() only iterates over all reserved tags
and requests which are not in IDLE state, ufshcd_compl_tm() never gets a
chance to run. Thus, TMR always ends up with completion timeout. Fix it by
calling blk_mq_start_request() in __ufshcd_issue_tm_cmd().
Link: https://lore.kernel.org/r/1617262750-4864-2-git-send-email-cang@codeaurora.org Fixes: 69a6c269c097 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Manage TMF tags with blk_{get,put}_request() instead of
ufshcd_get_tm_free_slot() / ufshcd_put_tm_slot(). Store a per-request
completion pointer in request.end_io_data instead of using a waitqueue to
report TMF completion.
Cc: Can Guo <cang@codeaurora.org> Cc: Stanley Chu <stanley.chu@mediatek.com> Cc: Avri Altman <avri.altman@wdc.com> Cc: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191209181309.196233-3-bvanassche@acm.org Tested-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Instead of tracking which tags are in use in the ufs_hba.lrb_in_use
bitmask, rely on the block layer tag allocation mechanism. This patch
removes the following busy-waiting loop if ufshcd_issue_devman_upiu_cmd()
and the block layer accidentally allocate the same tag for a SCSI request:
Support for UDP_GRO was added in the past but the implementation for
getsockopt was missed which did lead to an error when we tried to
retrieve the setting for UDP_GRO. This patch adds the missing switch
case for UDP_GRO
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.") Signed-off-by: Norman Maurer <norman_maurer@apple.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We should set the platform device's driver data to NULL here so that
code doesn't assume the struct drm_device pointer is valid when it could
have been destroyed. The lifetime of this pointer is managed by a kref
but when msm_drm_init() fails we call drm_dev_put() on the pointer which
will free the pointer's memory. This driver uses the component model, so
there's sort of two "probes" in this file, one for the platform device
i.e. msm_pdev_probe() and one for the component i.e. msm_drm_bind(). The
msm_drm_bind() code is using the platform device's driver data to store
struct drm_device so the two functions are intertwined.
This relationship becomes a problem for msm_pdev_shutdown() when it
tests the NULL-ness of the pointer to see if it should call
drm_atomic_helper_shutdown(). The NULL test is a proxy check for if the
pointer has been freed by kref_put(). If the drm_device has been
destroyed, then we shouldn't call the shutdown helper, and we know that
is the case if msm_drm_init() failed, therefore set the driver data to
NULL so that this pointer liveness is tracked properly.
Fixes: 9d5cbf5fe46e ("drm/msm: add shutdown support for display platform_driver") Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Krishna Manikandan <mkrishn@codeaurora.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Message-Id: <20210325212822.3663144-1-swboyd@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If veb-stats was enabled, the ethtool stats triggered a warning
due to invalid size: 'unexpected stat size for veb.tc_%u_tx_packets'.
This was due to an incorrect structure definition for the statistics.
Structures and functions have been improved in line with requirements
for the presentation of statistics, in particular for the functions:
'i40e_add_ethtool_stats' and 'i40e_add_stat_strings'.
Fixes: 1510ae0be2a4 ("i40e: convert VEB TC stats to use an i40e_stats array") Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com> Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When building with W=1, gcc points out that the __packed attribute
on struct qm_eqcr_entry conflicts with the 8-byte alignment
attribute on struct qm_fd inside it:
drivers/soc/fsl/qbman/qman.c:189:1: error: alignment 1 of 'struct qm_eqcr_entry' is less than 8 [-Werror=packed-not-aligned]
I assume that the alignment attribute is the correct one, and
that qm_eqcr_entry cannot actually be unaligned in memory,
so add the same alignment on the outer struct.
In rds_message_map_pages, the rm is freed by rds_message_put(rm).
But rm is still used by rm->data.op_sg in return value.
My patch assigns ERR_CAST(rm->data.op_sg) to err before the rm is
freed to avoid the uaf.
Fixes: 7dba92037baf3 ("net/rds: Use ERR_PTR for rds_message_alloc_sgs()") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.
Fixes: 81bfa206032a ("net/mlx5: Use a single IRQ for all async EQs") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.
Fixes: 5b4793f81745 ("net/mlx5e: Add support for reading connector type from PTYS") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
card->owner is a required property and since commit 81033c6b584b ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Add it.
This fixes following warning observed on Lamobo R1:
WARNING: CPU: 1 PID: 190 at sound/core/init.c:207 snd_card_new+0x430/0x480 [snd]
Modules linked in: sun4i_codec(E+) sun4i_backend(E+) snd_soc_core(E) ...
CPU: 1 PID: 190 Comm: systemd-udevd Tainted: G C E 5.10.0-1-armmp #1 Debian 5.10.4-1
Hardware name: Allwinner sun7i (A20) Family
Call trace:
(snd_card_new [snd])
(snd_soc_bind_card [snd_soc_core])
(snd_soc_register_card [snd_soc_core])
(sun4i_codec_probe [sun4i_codec])
Fixes: 45fb6b6f2aa3 ("ASoC: sunxi: add support for the on-chip codec on early Allwinner SoCs")
Related: commit 3c27ea23ffb4 ("ASoC: qcom: Set card->owner to avoid warnings")
Related: commit ec653df2a0cb ("drm/vc4/vc4_hdmi: fill ASoC card owner") Cc: linux-arm-kernel@lists.infradead.org Cc: alsa-devel@alsa-project.org Signed-off-by: Bastian Germann <bage@linutronix.de> Link: https://lore.kernel.org/r/20210331151843.30583-1-bage@linutronix.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dda2 ("net: phy: broadcom: Allow enabling or disabling of EEE") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.
Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.
Fixes: 8af56f40e53b ("nfp: flower: offload merge flows") Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021f0 ("net/ncsi: Stop monitor if channel times out or is inactive") Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880d5 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module") Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.
Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.
My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.
Fixes: cb1b728096f54 ("tipc: eliminate race condition at multicast reception") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.
Fixes: 80a95a80d358 ("cxgb4: collect SGE PF/VF queue map") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: 3d23a05c75c7 ("gianfar: Enable changing mac addr when if up") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since commit f5223e9eee65 ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.
The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.
Fixes: f5223e9eee65 ("can: extend sockaddr_can to include j1939 members") Reported-by: Richard Weinberger <richard@nod.at> Tested-by: Richard Weinberger <richard@nod.at> Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t Link: https://lore.kernel.org/r/20210325125850.1620-1-socketcan@hartkopp.net Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch> Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm") Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ") Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.
Fixes: 6f595959c095 ("amd-xgbe: Adjust register settings to improve performance") Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
1) argument should not be freed in any case - the caller already has
it as ->s_fs_info (and uses it a lot afterwards)
2) allocate readlink buffer with kmalloc() - the caller has no way
to tell if it's got that (on absolute symlink) or a result of
kasprintf(). Sure, for SLAB and SLUB kfree() works on results of
kmem_cache_alloc(), but that's not documented anywhere, might change
in the future *and* is already not true for SLOB.
Fixes: 52b209f7b848 ("get rid of hostfs_read_inode()") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Improve readability and maintainability by replacing a hardcoded string
allocation and formatting by the use of the kasprintf() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.
Fixes: d43d60e5eb95 ("i40e: ensure reset occurs when disabling VF") Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com> Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add Asym_Pause to supported link modes (it is supported by HW).
Lack of Asym_Pause in supported modes can cause several problems,
i.e. it won't be possible to turn the autonegotiation on
with asymmetric pause settings (i.e. Tx on, Rx off).
Fixes: 4e91bcd5d47a ("i40e: Finish implementation of ethtool get settings") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When xfrm interfaces are used in combination with namespaces
and ESP offload, we get a dst_entry NULL pointer dereference.
This is because we don't have a dst_entry attached in the ESP
offloading case and we need to do a policy lookup before the
namespace transition.
Fix this by expicit checking of skb_dst(skb) before accessing it.
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d519f ("ASoC: codec: wm9860: Refactor PLL out freq search") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Now in esp4/6_gso_segment(), before calling inner proto .gso_segment,
NETIF_F_CSUM_MASK bits are deleted, as HW won't be able to do the
csum for inner proto due to the packet encrypted already.
So the UDP/TCP packet has to do the checksum on its own .gso_segment.
But SCTP is using CRC checksum, and for that NETIF_F_SCTP_CRC should
be deleted to make SCTP do the csum in own .gso_segment as well.
In Xiumei's testing with SCTP over IPsec/veth, the packets are kept
dropping due to the wrong CRC checksum.
Reported-by: Xiumei Mu <xmu@redhat.com> Fixes: 7862b4058b9f ("esp: Add gso handlers for esp4 and esp6") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A sequence counter write section must be serialized or its internal
state can get corrupted. The "xfrm_state_hash_generation" seqcount is
global, but its write serialization lock (net->xfrm.xfrm_state_lock) is
instantiated per network namespace. The write protection is thus
insufficient.
To provide full protection, localize the sequence counter per network
namespace instead. This should be safe as both the seqcount read and
write sections access data exclusively within the network namespace. It
also lays the foundation for transforming "xfrm_state_hash_generation"
data type from seqcount_t to seqcount_LOCKNAME_t in further commits.
Fixes: b65e3d7be06f ("xfrm: state: add sequence count to detect hash resizes") Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Fixes: e85c5a153fe237f2 ("regulator: Add ROHM BD9571MWV-M PMIC regulator driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210312130242.3390038-2-geert+renesas@glider.be Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Cc: stable@vger.kernel.org Suggested-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Updated after the upstream commit 3e9005be87777 required some changes
for Linux 5.4 ] Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock") Cc: stable@vger.kernel.org Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Move gswip_port_set_{speed, duplex, pause} calls from
gswip_phylink_mac_link_up to gswip_phylink_mac_config because the
data required for these functions is not available inside
gswip_phylink_mac_link_up yet in Linux 5.4 (it was only added with
Linux 5.7). ] Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Implement support for transferring XDP meta data into skb for
virtio_net driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
Tested with the script at
https://github.com/higebu/virtio_net-xdp-metadata-test.
Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/bpf/20200225033212.437563-2-yuya.kusakabe@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In some configurations, recovery is optional. So, don't throw an error
when it is not used because e.g. pinctrl settings for recovery are not
provided. Reword the message and make it debug output.
Reported-by: Klaus Kudielka <klaus.kudielka@gmail.com> Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Use sysfs_lock to synchronize event handler with sysfs paths
in usbip drivers.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Use sysfs_lock to protect sysfs paths in stub-dev.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
This problem is common to all drivers while it can be reproduced easily
in vhci_hcd. Add a sysfs_lock to usbip_device struct to protect the paths.
Use this in vhci_hcd to protect sysfs paths. For a complete fix, usip_host
and usip-vudc drivers and the event handler will have to use this lock to
protect the paths. These changes will be done in subsequent patches.
Currently the mentioned helper can end-up freeing the socket wmem
without waking-up any processes waiting for more write memory.
If the partially orphaned skb is attached to an UDP (or raw) socket,
the lack of wake-up can hang the user-space.
Even for TCP sockets not calling the sk destructor could have bad
effects on TSQ.
Address the issue using skb_orphan to release the sk wmem before
setting the new sock_efree destructor. Additionally bundle the
whole ownership update in a new helper, so that later other
potential users could avoid duplicate code.
v1 -> v2:
- use skb_orphan() instead of sort of open coding it (Eric)
- provide an helper for the ownership change (Eric)
Fixes: f6ba8d33cfbb ("netem: fix skb_orphan_partial()") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Found by virtue of ipv6 raw sockets not honouring the per-socket
IP{,V6}_FREEBIND setting.
Based on hits found via:
git grep '[.]ip_nonlocal_bind'
We fix both raw ipv6 sockets to honour IP{,V6}_FREEBIND and IP{,V6}_TRANSPARENT,
and we fix sctp sockets to honour IP{,V6}_TRANSPARENT (they already honoured
FREEBIND), and not just the ipv6 'ip_nonlocal_bind' sysctl.
The helper is defined as:
static inline bool ipv6_can_nonlocal_bind(struct net *net, struct inet_sock *inet) {
return net->ipv6.sysctl.ip_nonlocal_bind || inet->freebind || inet->transparent;
}
so this change only widens the accepted opt-outs and is thus a clean bugfix.
I'm not entirely sure what 'fixes' tag to add, since this is AFAICT an ancient bug,
but IMHO this should be applied to stable kernels as far back as possible.
As such I'm adding a 'fixes' tag with the commit that originally added the helper,
which happened in 4.19. Backporting to older LTS kernels (at least 4.9 and 4.14)
would presumably require open-coding it or backporting the helper as well.
Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 83ba4645152d ("net: add helpers checking if socket can be bound to nonlocal address") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-By: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.
This has been observed using the following setup:
|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0
The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.
This patch resolves the following warning on a non-patched kernel:
The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.
Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4fd ("mac80211: add an optional TXQ for other PS-buffered frames") Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Null pointer dereference happens on master->slaves dereference in
teql_destroy() as master is null-pointer.
When qdisc_create() calls teql_qdisc_init() it imediately fails after
check "if (m->dev == dev)" because both devices are teql0, and it does
not set qdisc_priv(sch)->m leaving it zero on error path, then
qdisc_create() imediately calls teql_destroy() which does not expect
zero master pointer and we get OOPS.
Fixes: 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation") Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20af ("i40e: Log info when PF is entering and leaving Allmulti mode.") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 924a9bc362a5 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
Fixes: 924a9bc362a5 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Balazs Nemeth <bnemeth@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In '4da6a196f93b1' we fixed a potential unhash loop caused when
a TLS socket in a sockmap was removed from the sockmap. This
happened because the unhash operation on the TLS ctx continued
to point at the sockmap implementation of unhash even though the
psock has already been removed. The sockmap unhash handler when a
psock is removed does the following,
rcu_read_lock();
psock = sk_psock(sk);
if (unlikely(!psock)) {
rcu_read_unlock();
if (sk->sk_prot->unhash)
sk->sk_prot->unhash(sk);
return;
}
[...]
}
The unlikely() case is there to handle the case where psock is detached
but the proto ops have not been updated yet. But, in the above case
with TLS and removed psock we never fixed sk_prot->unhash() and unhash()
points back to sock_map_unhash resulting in a loop. To fix this we added
this bit of code,
This will set the sk_prot->unhash back to its saved value. This is the
correct callback for a TLS socket that has been removed from the sock_map.
Unfortunately, this also overwrites the unhash pointer for all psocks.
We effectively break sockmap unhash handling for any future socks.
Omitting the unhash operation will leave stale entries in the map if
a socket transition through unhash, but does not do close() op.
To fix set unhash correctly before calling into tls_update. This way the
TLS enabled socket will point to the saved unhash() handler.
Fixes: 4da6a196f93b1 ("bpf: Sockmap/tls, during free we may call tcp_bpf_unhash() in loop") Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: Lorenz Bauer <lmb@cloudflare.com> Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/161731441904.68884.15593917809745631972.stgit@john-XPS-13-9370 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).
My patch adds a return when the skb was freed.
Fixes: bcf0cafab44fd ("nfp: split out common control message handling code") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c705 ("HSO: add option hso driver") Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac82 ("ice: Refactor switch rule management structures and functions") Signed-off-by: Robert Malz <robertx.malz@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add handling of allocation fault for ice_vsi_list_map_info.
Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming") Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com> Co-developed-by: Haiyue Wang <haiyue.wang@intel.com> Signed-off-by: Haiyue Wang <haiyue.wang@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac804 ("ice: Add support for control queues") Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
KMSAN found uninitialized value at batadv_tt_prepare_tvlv_local_data()
[1], for commit ced72933a5e8ab52 ("batman-adv: use CRC32C instead of CRC16
in TT code") inserted 'reserved' field into "struct batadv_tvlv_tt_data"
and commit 7ea7b4a142758dea ("batman-adv: make the TT CRC logic VLAN
specific") moved that field to "struct batadv_tvlv_tt_vlan_data" but left
that field uninitialized.
Reported-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com> Tested-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: ced72933a5e8ab52 ("batman-adv: use CRC32C instead of CRC16 in TT code") Fixes: 7ea7b4a142758dea ("batman-adv: make the TT CRC logic VLAN specific") Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org> Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: <stable@vger.kernel.org> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit b344d6a83d01 ("parisc: add support for cmpxchg on u8 pointers")
can generate a sparse warning ("cast truncates bits from constant
value"), which has been reported several times [1] [2] [3].
The original code worked as expected, but anyway, let silence such
sparse warning as what others did [4].
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com Fixes: b1058b981272 ("direct-io: submit bio after boundary buffer is added to it") Signed-off-by: Jack Qiu <jack.qiu@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c033 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested] Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit cb9f753a3731 ("mm: fix races between swapoff and flush dcache")
updated flush_dcache_page implementations on several architectures to
use page_mapping_file() in order to avoid races between page_mapping()
and swapoff().
This update missed arch/nds32 and there is a possibility of a race
there.
Replace page_mapping() with page_mapping_file() in nds32 implementation
of flush_dcache_page().
Link: https://lkml.kernel.org/r/20210330175126.26500-1-rppt@kernel.org Fixes: cb9f753a3731 ("mm: fix races between swapoff and flush dcache") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Greentime Hu <green.hu@gmail.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Nick Hu <nickhu@andestech.com> Cc: Vincent Chen <deanbo422@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
LLVM changed the expected function signature for llvm_gcda_emit_function()
in the clang-11 release. Users of clang-11 or newer may have noticed
their kernels producing invalid coverage information:
Fix up the function signatures so calling this function interprets its
parameters correctly and computes the correct cfg checksum. In
particular, in clang-11, the additional checksum is no longer optional.
intel_dsm_platform_mux_info() tries to parse the ACPI package data
from _DSM for the debug information, but it assumes the fixed format
without checking what values are stored in the elements actually.
When an unexpected value is returned from BIOS, it may lead to GPF or
NULL dereference, as reported recently.
Add the checks of the contents in the returned values and skip the
values for invalid cases.
v1->v2: Check the info contents before dereferencing, too
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference") Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Unmask operation must be called with interrupt disabled,
on preempt_rt spin_lock_irqsave/spin_unlock_irqrestore
don't disable/enable interrupts, so use raw_* implementation
and change lock variable in struct irq_info from spinlock_t
to raw_spinlock_t
Cc: stable@vger.kernel.org Fixes: 25da4618af24 ("xen/events: don't unmask an event channel when an eoi is pending") Signed-off-by: Luca Fancellu <luca.fancellu@arm.com> Reviewed-by: Julien Grall <jgrall@amazon.com> Reviewed-by: Wei Liu <wei.liu@kernel.org> Link: https://lore.kernel.org/r/20210406105105.10141-1-luca.fancellu@arm.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
sk->sk_node->next will point to itself, that will make an endless loop
and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
llcp_sock_connect() to avoid repeated invoking.
Fixes: b4011239a08e ("NFC: llcp: Fix non blocking sockets connections") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Link: https://www.openwall.com/lists/oss-security/2020/11/01/1 Cc: <stable@vger.kernel.org> #v3.11 Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In llcp_sock_connect(), use kmemdup to allocate memory for
"llcp_sock->service_name". The memory is not released in the sock_unlink
label of the subsequent failure branch.
As a result, memory leakage occurs.
fix CVE-2020-25672
Fixes: d646960f7986 ("NFC: Initial LLCP support") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Link: https://www.openwall.com/lists/oss-security/2020/11/01/1 Cc: <stable@vger.kernel.org> #v3.3 Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
nfc_llcp_local_get() is invoked in llcp_sock_connect(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25671 Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Link: https://www.openwall.com/lists/oss-security/2020/11/01/1 Cc: <stable@vger.kernel.org> #v3.6 Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
nfc_llcp_local_get() is invoked in llcp_sock_bind(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25670 Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Link: https://www.openwall.com/lists/oss-security/2020/11/01/1 Cc: <stable@vger.kernel.org> #v3.6 Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The SST firmware's media and deep-buffer inputs are hardcoded to
S16LE, the corresponding DAIs don't have a hw_params callback and
their prepare callback also does not take the format into account.
So far the advertising of non working S24LE support has not caused
issues because pulseaudio defaults to S16LE, but changing pulse-audio's
config to use S24LE will result in broken sound.
Pipewire is replacing pulse now and pipewire prefers S24LE over S16LE
when available, causing the problem of the broken S24LE support to
come to the surface now.
Cc: stable@vger.kernel.org BugLink: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/866 Fixes: 098c2cd281409 ("ASoC: Intel: Atom: add 24-bit support for media playback and capture") Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210324132711.216152-2-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We've got a report about Acer Aspire E1 (PCI SSID 1025:0840) that
loses the speaker output after resume. With the comparison of COEF
dumps, it was identified that the COEF 0x0d bits 0x6000 corresponds to
the speaker amp.
This patch adds the specific quirk for the device to restore the COEF
bits at the codec (re-)initialization.
Add a control to the card before copying the id so that the numid field
is initialized in the copy. Otherwise the numid field of active_id,
format_id, rate_id and channels_id will be the same (0) and
snd_ctl_notify() will not queue the events properly.
Signed-off-by: Jonas Holmberg <jonashg@axis.com> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210407075428.2666787-1-jonashg@axis.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ceiling value may be miss-aligned with what's actually configured into the
ARR register. This is seen after probe as currently the ARR value is zero,
whereas ceiling value is set to the maximum. So:
- reading ceiling reports zero
- in case the counter gets enabled without any prior configuration,
it won't count.
- in case the function gets set by the user 1st, (priv->ceiling) is used.
Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
the ARR register value directly by using regmap read or write when needed.
There should be no drawback on performance as priv->ceiling isn't used in
performance critical path.
There's also no point in writing ARR while setting function (sms), so
it can be safely removed.
Fixes: ad29937e206f ("counter: Add STM32 Timer quadrature encoder") Suggested-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/1614793789-10346-1-git-send-email-fabrice.gasnier@foss.st.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[sudip: adjuct context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
arm64/crash_core: Export TCR_EL1.T1SZ in vmcoreinfo
BugLink: https://bugs.launchpad.net/bugs/1919275
TCR_EL1.TxSZ, which controls the VA space size, is configured by a
single kernel image to support either 48-bit or 52-bit VA space.
If the ARMv8.2-LVA optional feature is present and we are running
with a 64KB page size, then it is possible to use 52-bits of address
space for both userspace and kernel addresses. However, any kernel
binary that supports 52-bit must also be able to fall back to 48-bit
at early boot time if the hardware feature is not present.
Since TCR_EL1.T1SZ indicates the size of the memory region addressed by
TTBR1_EL1, export the same in vmcoreinfo. User-space utilities like
makedumpfile and crash-utility need to read this value from vmcoreinfo
for determining if a virtual address lies in the linear map range.
While at it also add documentation for TCR_EL1.T1SZ variable being
added to vmcoreinfo.
It indicates the size offset of the memory region addressed by
TTBR1_EL1.
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com> Tested-by: John Donnelly <john.p.donnelly@oracle.com> Tested-by: Kamlakant Patel <kamlakantp@marvell.com> Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com> Reviewed-by: James Morse <james.morse@arm.com> Reviewed-by: Amit Daniel Kachhap <amit.kachhap@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Steve Capper <steve.capper@arm.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Dave Anderson <anderson@redhat.com> Cc: Kazuhito Hagio <k-hagio@ab.jp.nec.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Cc: kexec@lists.infradead.org Link: https://lore.kernel.org/r/1589395957-24628-3-git-send-email-bhsharma@redhat.com
[catalin.marinas@arm.com: removed vabits_actual from the commit log] Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(backported from commit bbdbc11804ff0b4130e7550113b452e96a74d16e)
[hook 1: resolve conflict in documentation] Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Guilherme Piccoli <gpiccoli@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While allmodconfig and allyesconfig build for s390 there are also
various bots running compile tests with randconfig, where PCI is
disabled. This reveals that a lot of drivers should actually depend on
HAS_IOMEM.
Adding this to each device driver would be a never ending story,
therefore just disable COMPILE_TEST for s390.
The reasoning is more or less the same as described in
commit bc083a64b6c0 ("init/Kconfig: make COMPILE_TEST depend on !UML").
Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
nvme-mpath: replace direct_make_request with generic_make_request
BugLink: https://bugs.launchpad.net/bugs/1923874
The below patches caused a regression in a multipath setup: Fixes: 9f98772ba307 ("nvme-rdma: fix controller reset hang during traffic") Fixes: 2875b0aecabe ("nvme-tcp: fix controller reset hang during traffic")
These patches on their own are correct because they fixed a controller reset
regression.
When we reset/teardown a controller, we must freeze and quiesce the namespaces
request queues to make sure that we safely stop inflight I/O submissions.
Freeze is mandatory because if our hctx map changed between reconnects,
blk_mq_update_nr_hw_queues will immediately attempt to freeze the queue, and
if it still has pending submissions (that are still quiesced) it will hang.
This is what the above patches fixed.
However, by freezing the namespaces request queues, and only unfreezing them
when we successfully reconnect, inflight submissions that are running
concurrently can now block grabbing the nshead srcu until either we successfully
reconnect or ctrl_loss_tmo expired (or the user explicitly disconnected).
This caused a deadlock [1] when a different controller (different path on the
same subsystem) became live (i.e. optimized/non-optimized). This is because
nvme_mpath_set_live needs to synchronize the nshead srcu before requeueing I/O
in order to make sure that current_path is visible to future (re)submisions.
However the srcu lock is taken by a blocked submission on a frozen request
queue, and we have a deadlock.
In recent kernels (v5.9+) direct_make_request was replaced by submit_bio_noacct
which does not have this issue because it bio_list will be active when
nvme-mpath calls submit_bio_noacct on the bottom device (because it was
populated when submit_bio was triggered on it.
Hence, we need to fix all the kernels that were before submit_bio_noacct was
introduced.
projects / mirror_ubuntu-focal-kernel.git / log