iwlwifi: get the correct HCMD in the response handler
Until now, the response handler of a Host Command got the
exact same pointer that was also given to the DMA engine.
We almost never need to the Host Command that was sent while
handling its response, but when we do need it, we see that
the command has been modified.
This mystery has been elucidated. The FH (our DMA engine)
writes its meta data on the buffer in the DRAM. Of course it
copies the buffer to the NIC first. This was known to happen
for Tx command, but as a matter of fact, it happens to all
TFD brought by the FH which doesn't care much about what it
brings from DRAM to internal SRAM.
So copy the Host Command to yet another buffer so that we
can properly pass the buffer that was sent originally to the
fw. Do that only if it was request by the user since very
few flows need to get the HCMD sent in the response handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The generic part of the driver now creates all debugfs
directories. It creates a root directory directly in
the the root of the debugfs filesystem and within that
directories for each device, named after the device ID
of the devices iwlwifi is attached to.
In the cfg80211/mac80211 directory there's now a link
to the toplevel iwlwifi debugfs directory to make it
easier to find the debugfs files.
cfg80211: Fix mutex locking in reg_last_request_cell_base
should fix the following issue
[ 3229.815012] [ BUG: lock held when returning to user space! ]
[ 3229.815016] 3.5.0-rc7-wl #28 Tainted: G W O
[ 3229.815017]
------------------------------------------------
[ 3229.815019] wpa_supplicant/5783 is leaving the kernel with locks still held!
[ 3229.815022] 1 lock held by wpa_supplicant/5783:
[ 3229.815023] #0: (reg_mutex){+.+.+.}, at: [<fa65834d>]
reg_last_request_cell_base+0x1d/0x60 [cfg80211]
Cc: Luis Rodriguez <mcgrof@gmail.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Tested-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug. Increase it to 1500ms.
wlcore: wait for command completion event when sending CMD_ROLE_STOP
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
handle errors of nla_put() inside the if(nla_put...) {}
This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
wlcore/wl12xx: calibrator fem detect implementation
this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.
this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
wl18xx: fix bogus compile warning on cc config option
Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).
drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
wlcore: send EAPOLs using minimum basic rate for all roles
Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
wlcore: don't re-configure wakeup conditions if not needed
suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Johannes Berg [Tue, 17 Jul 2012 15:12:29 +0000 (17:12 +0200)]
b43: fix crash with OpenFWWF
b43 with open firmware crashes mac80211 because
it changes the number of queues at runtime which,
while it was never really supported, now crashes
mac80211 due to the new hardware queue logic.
Fix this by detecting open vs. proprietary fw
earlier and registering with mac80211 with the
right number of queues.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: stable@vger.kernel.org (depends on commit a6f38ac3) Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do not set/clear TSF when adding/deleting an interface.
This should be done when the BSS is set up and should also
take into account the existence of other interfaces.
* Set opmode explicitly.
* ANI setup needs to be decided based on multiple interfaces.
This can be done via the bss_info_changed() callback.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sun, 15 Jul 2012 22:48:00 +0000 (23:48 +0100)]
libertas USB: don't set surpriseremoved flag
We found a deadlock in the handling of command failures/reset conditions.
For example:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is queued (but not yet sent to the hardware)
4. The device reset kicks in, causing the if_usb disconnect handler to
set the "surprise removed" flag to be set as the device disappears
from the bus. This causes lbs_thread to stop processing things
("adapter removed; waiting to die"), not processing any further
commands, leaving the second queued command "in the air", causing a
deadlock.
Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sun, 15 Jul 2012 22:47:51 +0000 (23:47 +0100)]
libertas: handle command failure immediately
Fail commands immediately when the request cannot be sent to the hardware.
This solves the following deadlock:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is submitted to the device, and fails. The failure
is noted but the existing code waits for the timeout handler to take
care of the failure.
4. The device reset kicks in, causing the device "surprise removed" flag
to be set as the device disappears from the bus.
5. lbs_thread notes this and enters "adapter removed; waiting to die"
mode, without processing any further command timeouts.
While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sun, 15 Jul 2012 22:44:58 +0000 (23:44 +0100)]
libertas: Update 11d info only when interface is active
reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 15 Jul 2012 17:53:38 +0000 (19:53 +0200)]
ath9k_hw: clean up AR9003 EEPROM code
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
access the relevant fields directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 15 Jul 2012 17:53:36 +0000 (19:53 +0200)]
ath9k: fix aggregate size limit based on queue TXOP limit
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.
The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.
Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.
Reported-by: Dave Täht <dave.taht@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 15 Jul 2012 17:53:34 +0000 (19:53 +0200)]
ath9k/ath9k_htc: fix txop limit handling
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 15 Jul 2012 17:53:33 +0000 (19:53 +0200)]
ath9k_hw: remove redundant arguments to INIT_INI_ARRAY
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 15 Jul 2012 17:53:30 +0000 (19:53 +0200)]
ath9k: validate rx antenna settings
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: improvement in cfg80211 set_bitrate_mask handler
This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
mwifiex: add support to use basic rates in ibss join request
In mwifiex_set_rf_channel() ibss specific flags were unnecessarily
getting modified for infra and AP mode. This patch removes
mwifiex_set_rf_channel() function and adds equivalant code in infra,
ibss and AP path.
For ibss, now we are chosing band based on channel type and basic
rates provided in ibss join request. We can start ibss network in
A only, B only, G only, BG, BGN, AN mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: remove unnecessary code in data rate configuration
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: remove redundant code in set channel path
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Forest Bond [Fri, 13 Jul 2012 16:26:06 +0000 (12:26 -0400)]
rtlwifi: rtl8192de: Fix phy-based version calculation
Commit d83579e2a50ac68389e6b4c58b845c702cf37516 incorporated some
changes from the vendor driver that made it newly important that the
calculated hardware version correctly include the CHIP_92D bit, as all
of the IS_92D_* macros were changed to depend on it. However, this bit
was being unset for dual-mac, dual-phy devices. The vendor driver
behavior was modified to not do this, but unfortunately this change was
not picked up along with the others. This caused scanning in the 2.4GHz
band to be broken, and possibly other bugs as well.
This patch brings the version calculation logic in parity with the
vendor driver in this regard, and in doing so fixes the regression.
However, the version calculation code in general continues to be largely
incoherent and messy, and needs to be cleaned up.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com> Cc: Stable <stable@vger.kernel.org> [v3.2+] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 13 Jul 2012 08:57:36 +0000 (10:57 +0200)]
b43: use temporary rate_index for error checking
The mac80211 rate_index changed to be a u8, so
can't hold the negative error value properly.
Use a temporary variable for error checking.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: make CONFIG_ATH9K_DFS_CERTIFIED depend on CFG80211_CERTIFICATION_ONUS
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The configuration request/response messages contain a configuration
field which contains the sliding window size (amount of unacked reliable
packets that can be pending). This patch makes sure that we configure
the correct size (minimum of local and remote values) and use it when
determining whether to send new packets or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Mon, 16 Jul 2012 13:12:17 +0000 (16:12 +0300)]
Bluetooth: Remove unnecessary h5_build_pkt function
The implementation of h5_build_packet can be moved into
h5_prepare_pkt since all h5_prepare_pkt does is determine whether the
packet is reliable and then call h5_build_packet.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Mon, 16 Jul 2012 13:12:16 +0000 (16:12 +0300)]
Bluetooth: Implement proper low-power support for Three-wire UART
This patch adds on-demand wakeup request sending (and re-sendind) when
we are in low-power state. When the controller enters this state it will
send a sleep message after which the host is not allowed to send any
other packets until a wakeup request has been sent and the woken message
received as a response to it. The wakeup requests are re-sent
periodically until a woken message is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Mon, 16 Jul 2012 13:12:15 +0000 (16:12 +0300)]
Bluetooth: Add initialization tracking to HCI Three-wire driver
This patch adds tracking for the uninitialized, initialized and active
states for Three-wire UART. This is needed so we can handle periodic
sending of the Link Establishment messages before reaching active state
and so that we do not try to do any higher level HCI data transmission
before reaching active state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Mon, 16 Jul 2012 13:12:14 +0000 (16:12 +0300)]
Bluetooth: Add initial sleep support to Three-wire UART
This patch adds very basic support for the sleep related messages. The
only thing the code does right now is send a wakeup message as soon as
receiving a sleep one, essentially preventing the controller from going
to sleep.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Mon, 16 Jul 2012 13:12:11 +0000 (16:12 +0300)]
Bluetooth: Add delayed init sequence support for UART controllers
This patch makes it possible to have UART drivers perform an internal
initialization before calling hci_register_dev. This allows moving a lot
of init code from user space (hciattach) to the kernel side, thereby
creating a more controlled/robust initialization process.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
on disassoc, ieee80211_set_disassoc() goes out of PS
before indicating BSS_CHANGED_ASSOC (not sure why this
is needed, but some drivers might count on the current
behavior).
However, it does it after sending the disassoc
frame, which results in null-data frame being sent
(in order to go out of ps) after we were already sent
the disassoc, which is invalid.
Fix it by going out of ps before sending the disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
regulatory_update() just calls wiphy_update_regulatory().
wiphy_update_regulatory() assumes you already have
the reg_mutex held so just move the call within locking
context and kill the superfluous regulatory_update().
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: rename reg_device_remove() to wiphy_regulatory_deregister()
This makes it clearer what we're doing. This now makes a bit
more sense given that regardless of the wiphy if the cell
base station hint feature is supported we will be modifying the
way the regulatory core behaves.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: add cellular base station regulatory hint support
Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.
The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds CONFIG_CFG80211_CERTIFICATION_ONUS which is to
be used for features / code which require a bit of work on
the system integrator's part to ensure that the system will
still pass 802.11 regulatory certification. This option is
also usable for researchers and experimenters looking to add
code in the kernel without impacting compliant code.
We'd use CONFIG_EXPERT alone but it seems that most standard
Linux distributions are enabling CONFIG_EXPERT already. This
allows us to define 802.11 specific kernel features under a
flag that is intended by design to be disabled by standard
Linux distributions, and only enabled by system integrators
or distributions that have done work to ensure regulatory
certification on the system with the enabled features.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo [Thu, 12 Jul 2012 12:33:58 +0000 (15:33 +0300)]
cfg80211: fix set_regdom() to cancel requests with same alpha2
While adding regulatory support to ath6kl I noticed that I easily
got the regulatory code confused. The way to reproduce the bug was:
1. iw reg set FI (in userspace)
2. cfg80211 calls ath6kl_reg_notify(FI)
3. ath6kl sets regdomain in firmware
4. firmware sends regdomain event to notify about the new regdomain (FI)
5. ath6kl calls regulatory_hint(FI)
And this (from FI to FI transition) confuses cfg80211 and after that I
only get "Pending regulatory request, waiting for it to be
processed...." messages and regdomain changes won't work anymore.
The reason why ath6kl calls regulatory_hint() is that firmware can change
the regulatory domain by it's own, for example due to 11d IEs. I could
of course workaround this in ath6kl but I think it's better to handle
the case in cfg80211.
The fix is pretty simple, use a different error code if the regdomain is
same and then just set the request processed so that it doesn't block new
requests.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Thu, 12 Jul 2012 23:17:33 +0000 (16:17 -0700)]
cfg80211: support TX error rate CQM
Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.
On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: fix tx-mgmt cookie value being left uninitialized
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work(). But the latter is only
called where offchannel is needed. If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.
This patch sets the cookie value when offchannel isn't used.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johan Hedberg [Thu, 28 Jun 2012 10:44:30 +0000 (13:44 +0300)]
Bluetooth: Change page scan interval in fast connectable mode
This patch is based on a user space (hciops) patch which never made it
upstream but does make sense to include in the mgmt part of the kernel.
(User space) commit message from Dmitriy Paliy:
"
Page scan interval in fast connectable mode is changed from 22.5 msec to
160 msec to perform less aggressive page scanning. This is done
accordingly to controller vendor recommendation.
Primary concern is that current parameters 22.5 interval, 11.25 window,
and interleaved scanning occupy whole radio bandwidth. Changing interval
to 160 msec should be sufficient for both speeding up connection
establishment and leaving space for other activities, like inquiry scan,
e.g.
"
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 10 Jul 2012 12:47:07 +0000 (05:47 -0700)]
Bluetooth: Use tx window from config response for ack timing
This change addresses an L2CAP ERTM throughput problem when a remote
device does not fully utilize the available transmit window.
The L2CAP ERTM transmit window size determines the maximum number of
unacked frames that may be outstanding at any time. It is configured
separately for each direction of an ERTM connection. Each side sends a
configuration request with a tx_win field indicating how many unacked
frames it is capable of receiving before sending an ack. The
configuration response's tx_win field shows how many frames the
transmitter will actually send before waiting for an ack.
It's important to trace both the actual transmit window (to check for
validity of incoming frames) and the number of frames that the
transmitter will send before waiting (to send acks at the appropriate
time). Now there are separate tx_win and ack_win values. ack_win is
updated based on configuration responses, and is used to determine
when acks are sent.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Due to the tracking happening in NETDEV_PRE_UP, it had
introduced bugs because the monitor interface callback
would be called before the device was started. It looks
like there's no way to fix this, and using NETDEV_PRE_UP
is broken anyway (since there's no NETDEV_UP_FAIL), so
remove all that code, track interfaces in NETDEV_UP and
also stop tracking the monitor channel in cfg80211.
This mostly reverts to before the tracking, except that
we keep the interface count tracking so that setting the
monitor channel can be rejected properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 12 Jul 2012 17:45:08 +0000 (19:45 +0200)]
cfg80211/mac80211: re-add get_channel operation
This essentially reverts commit 2e165b818456 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / mirror_ubuntu-zesty-kernel.git / log