According to the datasheet tc358767 can transfer up to 16 bytes via
its AUX channel, so the artificial limit of 8 appears to be too
low. However only up to 15-bytes seem to be actually supported and
trying to use 16-byte transfers results in transfers failing
sporadically (with bogus status in case of I2C transfers), so limit it
to 15.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Chris Healy <cphealy@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-9-andrew.smirnov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The issue we have is that the crc worker might fall behind. We've
tried to handle this by tracking both the earliest frame for which it
still needs to compute a crc, and the last one. Plus when the
crtc_state changes, we have a new work item, which are all run in
order due to the ordered workqueue we allocate for each vkms crtc.
Trouble is there's been a few small issues in the current code:
- we need to capture frame_end in the vblank hrtimer, not in the
worker. The worker might run much later, and then we generate a lot
of crc for which there's already a different worker queued up.
- frame number might be 0, so create a new crc_pending boolean to
track this without confusion.
- we need to atomically grab frame_start/end and clear it, so do that
all in one go. This is not going to create a new race, because if we
race with the hrtimer then our work will be re-run.
- only race that can happen is the following:
1. worker starts
2. hrtimer runs and updates frame_end
3. worker grabs frame_start/end, already reading the new frame_end,
and clears crc_pending
4. hrtimer calls queue_work()
5. worker completes
6. worker gets re-run, crc_pending is false
Explain this case a bit better by rewording the comment.
v2: Demote warning level output to debug when we fail to requeue, this
is expected under high load when the crc worker can't quite keep up.
Cc: Shayenne Moura <shayenneluzmoura@gmail.com> Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Cc: Haneen Mohammed <hamohammed.sa@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Tested-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190606222751.32567-2-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1848046 Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since the rpmsg_endpoint is created before probe is called, it's
possible that a host event is received during cros_ec_register, and
there would be some pending work in the host_event_work workqueue while
cros_ec_register is called.
If cros_ec_register fails, when the leftover work in host_event_work
run, the ec_dev from the drvdata of the rpdev could be already set to
NULL, causing kernel crash when trying to run cros_ec_get_next_event.
Fix this by creating the rpmsg_endpoint by ourself, and when
cros_ec_register fails (or on remove), destroy the endpoint first (to
make sure there's no more new calls to cros_ec_rpmsg_callback), and then
cancel all works in the host_event_work workqueue.
Cc: stable@vger.kernel.org Fixes: 2de89fd98958 ("platform/chrome: cros_ec: Add EC host command support using rpmsg") Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
mt7615 patch/n9/cr4 firmwares are available in mediatek folder in
linux-firmware repository. Because of this mt7615 won't work on regular
distributions like Ubuntu. Fix path definitions. Moreover remove useless
firmware name pointers and use definitions directly
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Cc: stable@vger.kernel.org Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the drives in a RAID0 are not all the same size, the array is
divided into zones.
The first zone covers all drives, to the size of the smallest.
The second zone covers all drives larger than the smallest, up to
the size of the second smallest - etc.
A change in Linux 3.14 unintentionally changed the layout for the
second and subsequent zones. All the correct data is still stored, but
each chunk may be assigned to a different device than in pre-3.14 kernels.
This can lead to data corruption.
It is not possible to determine what layout to use - it depends which
kernel the data was written by.
So we add a module parameter to allow the old (0) or new (1) layout to be
specified, and refused to assemble an affected array if that parameter is
not set.
Fixes: 20d0189b1012 ("block: Introduce new bio_split()")
cc: stable@vger.kernel.org (3.14+) Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[Why]
When more than 2 displays are connected to the graphics card,
only the minimum memory clock is needed. However, when more
displays are connected, the minimum memory clock is not
sufficient enough to support the overwhelming bandwidth.
System will hang under this circumstance.
Also, the old code didn't address HBM cards, which has 2
pseudo channels. We need to add the HBM part here.
[How]
When graphics card connects to 2 or more displays,
switch to high memory clock. Also, choose memory
multiplier based on whether its regular DRAM or HBM.
Signed-off-by: Zhan Liu <zhan.liu@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There may be situations when a server negotiates SMB 2.1
protocol version or higher but responds to a CREATE request
with an oplock rather than a lease.
Currently the client doesn't handle such a case correctly:
when another CREATE comes in the server sends an oplock
break to the initial CREATE and the client doesn't send
an ack back due to a wrong caching level being set (READ
instead of RWH). Missing an oplock break ack makes the
server wait until the break times out which dramatically
increases the latency of the second CREATE.
Fix this by properly detecting oplocks when using SMB 2.1
protocol version and higher.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It should not be larger then the slab max buf size. If user
specifies a larger size, it passes this check and goes
straightly to SMB2_set_info_init performing an insecure memcpy.
Signed-off-by: Murphy Zhou <jencce.kernel@gmail.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes: 310c18a41450 ("i2c: riic: add driver") Cc: stable@vger.kernel.org Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com> Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
add_early_randomness() is called by hwrng_register() when the
hardware is added. If this hardware and its module are present
at boot, and if there is no data available the boot hangs until
data are available and can't be interrupted.
For instance, in the case of virtio-rng, in some cases the host can be
not able to provide enough entropy for all the guests.
We can have two easy ways to reproduce the problem but they rely on
misconfiguration of the hypervisor or the egd daemon:
- if virtio-rng device is configured to connect to the egd daemon of the
host but when the virtio-rng driver asks for data the daemon is not
connected,
- if virtio-rng device is configured to connect to the egd daemon of the
host but the egd daemon doesn't provide data.
The guest kernel will hang at boot until the virtio-rng driver provides
enough data.
To avoid that, call rng_get_data() in non-blocking mode (wait=0)
from add_early_randomness().
Signed-off-by: Laurent Vivier <lvivier@redhat.com> Fixes: d9e797261933 ("hwrng: add randomness to system from rng...") Cc: <stable@vger.kernel.org> Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Quoted from
commit 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize")
" At LSF we decided that if we truncate up from isize we shouldn't trim
fallocated blocks that were fallocated with KEEP_SIZE and are past the
new i_size. This patch fixes ext4 to do this. "
And generic/092 of fstest have covered this case for long time, however
is_quota_modification() didn't adjust based on that rule, so that in
below condition, we will lose to quota block change:
- fallocate blocks beyond EOF
- remount
- truncate(file_path, file_size)
Fix it.
Link: https://lore.kernel.org/r/20190911093650.35329-1-yuchao0@huawei.com Fixes: 3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize") CC: stable@vger.kernel.org Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Really enable warning when CONFIG_EXT4_DEBUG is set and fix missing
first argument. This was introduced in commit ff95ec22cd7f ("ext4:
add warning to ext4_convert_unwritten_extents_endio") and splitting
extents inside endio would trigger it.
Fixes: ff95ec22cd7f ("ext4: add warning to ext4_convert_unwritten_extents_endio") Signed-off-by: Rakesh Pandit <rakesh@tuxera.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
drivers/mtd/nand/raw/stm32_fmc2_nand.c: In function ‘stm32_fmc2_calc_timings’:
drivers/mtd/nand/raw/stm32_fmc2_nand.c:1417:23: warning: comparison is
always false due to limited range of data type [-Wtype-limits]
else if (tims->twait > FMC2_PMEM_PATT_TIMING_MASK)
V1->V2: in handle_one_rcv_msg, if data_size > 2, set requeue to zero and
goto out instead of calling ipmi_free_msg.
Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
In the source stack trace below, function set_need_watch tries to
take out the same si_lock that was taken earlier by ipmi_thread.
Upstream commit e1891cffd4c4896a899337a243273f0e23c028df adds code to
ipmi_smi_msg_received() to call smi_remove_watch() via intf_err_seq()
and this seems to be causing the deadlock.
commit e1891cffd4c4896a899337a243273f0e23c028df
Author: Corey Minyard <cminyard@mvista.com>
Date: Wed Oct 24 15:17:04 2018 -0500
ipmi: Make the smi watcher be disabled immediately when not needed
The fix is to put all messages in the queue and move the message
checking code out of ipmi_smi_msg_received and into handle_one_recv_msg,
which processes the message checking after ipmi_thread releases its
locks.
Additionally,Kosuke Tatsukawa <tatsu@ab.jp.nec.com> reported that
handle_new_recv_msgs calls ipmi_free_msg when handle_one_rcv_msg returns
zero, so that the call to ipmi_free_msg in handle_one_rcv_msg introduced
another panic when "ipmitool sensor list" was run in a loop. He
submitted this part of the patch.
+free_msg:
+ requeue = 0;
+ goto out;
Reported by: Osamu Samukawa <osa-samukawa@tg.jp.nec.com>
Characterized by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Signed-off-by: Tony Camuso <tcamuso@redhat.com> Fixes: e1891cffd4c4 ("ipmi: Make the smi watcher be disabled immediately when not needed") Cc: stable@vger.kernel.org # 5.1 Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hole puching currently evicts pages from page cache and then goes on to
remove blocks from the inode. This happens under both XFS_IOLOCK_EXCL
and XFS_MMAPLOCK_EXCL which provides appropriate serialization with
racing reads or page faults. However there is currently nothing that
prevents readahead triggered by fadvise() or madvise() from racing with
the hole punch and instantiating page cache page after hole punching has
evicted page cache in xfs_flush_unmap_range() but before it has removed
blocks from the inode. This page cache page will be mapping soon to be
freed block and that can lead to returning stale data to userspace or
even filesystem corruption.
Fix the problem by protecting handling of readahead requests by
XFS_IOLOCK_SHARED similarly as we protect reads.
CC: stable@vger.kernel.org Link: https://lore.kernel.org/linux-fsdevel/CAOQ4uxjQNmxqmtA_VbYW0Su9rKRk2zobJmahcyeaEVOFKVQ5dw@mail.gmail.com/ Reported-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently handling of MADV_WILLNEED hint calls directly into readahead
code. Handle it by calling vfs_fadvise() instead so that filesystem can
use its ->fadvise() callback to acquire necessary locks or otherwise
prepare for the request.
Suggested-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Boaz Harrosh <boazh@netapp.com> CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Filesystems will need to call this function from their fadvise handlers.
CC: stable@vger.kernel.org Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
syzbot found that a thread can stall for minutes inside read_mem() or
write_mem() after that thread was killed by SIGKILL [1]. Reading from
iomem areas of /dev/mem can be slow, depending on the hardware.
While reading 2GB at one read() is legal, delaying termination of killed
thread for minutes is bad. Thus, allow reading/writing /dev/mem and
/dev/kmem to be preemptible and killable.
Theoretically, reading/writing /dev/mem and /dev/kmem can become
"interruptible". But this patch chose "killable". Future patch will make
them "interruptible" so that we can revert to "killable" if some program
regressed.
Currently frame registrations are not purged, even when changing the
interface type. This can lead to potentially weird situations where
frames possibly not allowed on a given interface type remain registered
due to the type switching happening after registration.
The kernel currently relies on userspace apps to actually purge the
registrations themselves, this is not something that the kernel should
rely on.
Add a call to cfg80211_mlme_purge_registrations() to forcefully remove
any registrations left over prior to switching the iftype.
Cc: stable@vger.kernel.org Signed-off-by: Denis Kenzior <denkenz@gmail.com> Link: https://lore.kernel.org/r/20190828211110.15005-1-denkenz@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since commit 4ad23a976413 ("MD: use per-cpu counter for
writes_pending"), set_in_sync() is substantially more expensive: it
can wait for a full RCU grace period which can be 10s of milliseconds.
So we should only call it when the cost is justified.
md_check_recovery() currently calls set_in_sync() every time it finds
anything to do (on non-external active arrays). For an array
performing resync or recovery, this will be quite often.
Each call will introduce a delay to the md thread, which can noticeable
affect IO submission latency.
In md_check_recovery() we only need to call set_in_sync() if
'safemode' was non-zero at entry, meaning that there has been not
recent IO. So we save this "safemode was nonzero" state, and only
call set_in_sync() if it was non-zero.
This measurably reduces mean and maximum IO submission latency during
resync/recovery.
Reported-and-tested-by: Jack Wang <jinpu.wang@cloud.ionos.com> Fixes: 4ad23a976413 ("MD: use per-cpu counter for writes_pending") Cc: stable@vger.kernel.org (v4.12+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Until revalidate_disk() has completed, the size of a new md array will
appear to be zero.
So we shouldn't report, through array_state, that the array is active
until that time.
udev rules check array_state to see if the array is ready. As soon as
it appear to be zero, fsck can be run. If it find the size to be
zero, it will fail.
So add a new flag to provide an interlock between do_md_run() and
array_state_show(). This flag is set while do_md_run() is active and
it prevents array_state_show() from reporting that the array is
active.
Before do_md_run() is called, ->pers will be NULL so array is
definitely not active.
After do_md_run() is called, revalidate_disk() will have run and the
array will be completely ready.
We also move various sysfs_notify*() calls out of md_run() into
do_md_run() after MD_NOT_READY is cleared. This ensure the
information is ready before the notification is sent.
Prior to v4.12, array_state_show() was called with the
mddev->reconfig_mutex held, which provided exclusion with do_md_run().
Note that MD_NOT_READY cleared twice. This is deliberate to cover
both success and error paths with minimal noise.
Fixes: b7b17c9b67e5 ("md: remove mddev_lock() from md_attr_show()") Cc: stable@vger.kernel.org (v4.12++) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in
RAID6.") avoids rereading P when it can be computed from other members.
However, this misses the chance to re-write the right data to P. This
patch sets R5_ReadError if the re-read fails.
Also, when re-read is skipped, we also missed the chance to reset
rdev->read_errors to 0. It can fail the disk when there are many read
errors on P member disk (other disks don't have read error)
V2: upper layer read request don't read parity/Q data. So there is no
need to consider such situation.
This is Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in RAID6.") Cc: <stable@vger.kernel.org> #4.4+ Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
My assumption in commit b53548f9d9e4 ("spi: pxa2xx: Remove LPSS private
register restoring during resume") that Intel Lynxpoint and compatible
based chipsets may not need LPSS private registers saving and restoring
over suspend/resume cycle turned out to be false on Intel Broadwell.
Curtis Malainey sent a patch bringing above change back and reported the
LPSS SPI Chip Select control was lost over suspend/resume cycle on
Broadwell machine.
Instead of reverting above commit lets add LPSS private register
saving/restoring also for all LPSS SPI, I2C and UART controllers on
Lynxpoint and compatible chipset to make sure context is not lost in
case nothing else preserves it like firmware or if LPSS is always on.
Fixes: b53548f9d9e4 ("spi: pxa2xx: Remove LPSS private register restoring during resume") Reported-by: Curtis Malainey <cujomalainey@chromium.org> Tested-by: Curtis Malainey <cujomalainey@chromium.org> Cc: 5.0+ <stable@vger.kernel.org> # 5.0+ Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The GSS Message Integrity Check data for krb5i may lie partially in the XDR
reply buffer's pages and tail. If so, we try to copy the entire MIC into
free space in the tail. But as the estimations of the slack space required
for authentication and verification have improved there may be less free
space in the tail to complete this copy -- see commit 2c94b8eca1a2
("SUNRPC: Use au_rslack when computing reply buffer size"). In fact, there
may only be room in the tail for a single copy of the MIC, and not part of
the MIC and then another complete copy.
The real world failure reported is that `ls` of a directory on NFS may
sometimes return -EIO, which can be traced back to xdr_buf_read_netobj()
failing to find available free space in the tail to copy the MIC.
Fix this by checking for the case of the MIC crossing the boundaries of
head, pages, and tail. If so, shift the buffer until the MIC is contained
completely within the pages or tail. This allows the remainder of the
function to create a sub buffer that directly address the complete MIC.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Cc: stable@vger.kernel.org # v5.1 Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Ensure that we dequeue the request from the transport receive queue
while we're re-encoding to prevent issues like use-after-free when
we release the bvec.
Fixes: 7536908982047 ("SUNRPC: Ensure the bvecs are reset when we re-encode...") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[BUG]
With v5.3 kernel, we can't convert to SINGLE profile:
# btrfs balance start -f -dconvert=single $mnt
ERROR: error during balancing '/mnt/btrfs': Invalid argument
# dmesg -t | tail
validate_convert_profile: data profile=0x1000000000000 allowed=0x20 is_valid=1 final=0x1000000000000 ret=1
BTRFS error (device dm-3): balance: invalid convert data profile single
[CAUSE]
With the extra debug output added, it shows that the @allowed bit is
lacking the special in-memory only SINGLE profile bit.
Thus we fail at that (profile & ~allowed) check.
This regression is caused by commit 081db89b13cb ("btrfs: use raid_attr
to get allowed profiles for balance conversion") and the fact that we
don't use any bit to indicate SINGLE profile on-disk, but uses special
in-memory only bit to help distinguish different profiles.
[FIX]
Add that BTRFS_AVAIL_ALLOC_BIT_SINGLE to @allowed, so the code should be
the same as it was and fix the regression.
Reported-by: Chris Murphy <lists@colorremedies.com> Fixes: 081db89b13cb ("btrfs: use raid_attr to get allowed profiles for balance conversion") CC: stable@vger.kernel.org # 5.3+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There is a race between setting up a qgroup rescan worker and completing
a qgroup rescan worker that can lead to callers of the qgroup rescan wait
ioctl to either not wait for the rescan worker to complete or to hang
forever due to missing wake ups. The following diagram shows a sequence
of steps that illustrates the race.
Before the rescan worker started by the task at CPU 3 completes, if
another task calls btrfs_ioctl_quota_rescan(), it will get -EINPROGRESS
because the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN is set at
fs_info->qgroup_flags, which is expected and correct behaviour.
However if other task calls btrfs_ioctl_quota_rescan_wait() before the
rescan worker started by the task at CPU 3 completes, it will return
immediately without waiting for the new rescan worker to complete,
because fs_info->qgroup_rescan_running is set to false by CPU 2.
This race is making test case btrfs/171 (from fstests) to fail often:
btrfs/171 9s ... - output mismatch (see /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad)
# --- tests/btrfs/171.out 2018-09-16 21:30:48.505104287 +0100
# +++ /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad 2019-09-19 02:01:36.938486039 +0100
# @@ -1,2 +1,3 @@
# QA output created by 171
# +ERROR: quota rescan failed: Operation now in progress
# Silence is golden
# ...
# (Run 'diff -u /home/fdmanana/git/hub/xfstests/tests/btrfs/171.out /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad' to see the entire diff)
That is because the test calls the btrfs-progs commands "qgroup quota
rescan -w", "qgroup assign" and "qgroup remove" in a sequence that makes
calls to the rescan start ioctl fail with -EINPROGRESS (note the "btrfs"
commands 'qgroup assign' and 'qgroup remove' often call the rescan start
ioctl after calling the qgroup assign ioctl,
btrfs_ioctl_qgroup_assign()), since previous waits didn't actually wait
for a rescan worker to complete.
Another problem the race can cause is missing wake ups for waiters,
since the call to complete_all() happens outside a critical section and
after clearing the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN. In the sequence
diagram above, if we have a waiter for the first rescan task (executed
by CPU 2), then fs_info->qgroup_rescan_completion.wait is not empty, and
if after the rescan worker clears BTRFS_QGROUP_STATUS_FLAG_RESCAN and
before it calls complete_all() against
fs_info->qgroup_rescan_completion, the task at CPU 3 calls
init_completion() against fs_info->qgroup_rescan_completion which
re-initilizes its wait queue to an empty queue, therefore causing the
rescan worker at CPU 2 to call complete_all() against an empty queue,
never waking up the task waiting for that rescan worker.
Fix this by clearing BTRFS_QGROUP_STATUS_FLAG_RESCAN and setting
fs_info->qgroup_rescan_running to false in the same critical section,
delimited by the mutex fs_info->qgroup_rescan_lock, as well as doing the
call to complete_all() in that same critical section. This gives the
protection needed to avoid rescan wait ioctl callers not waiting for a
running rescan worker and the lost wake ups problem, since setting that
rescan flag and boolean as well as initializing the wait queue is done
already in a critical section delimited by that mutex (at
qgroup_rescan_init()).
Fixes: 57254b6ebce4ce ("Btrfs: add ioctl to wait for qgroup rescan completion") Fixes: d2c609b834d62f ("btrfs: properly track when rescan worker is running") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
for (( i = 0; i < 3; i++)); do
# Create 3 64M holes for latter fallocate to fail
truncate -s 192m $mnt/subv/file
xfs_io -c "pwrite 64m 4k" $mnt/subv/file > /dev/null
xfs_io -c "pwrite 128m 4k" $mnt/subv/file > /dev/null
sync
# it's supposed to fail, and each failure will leak at least 64M
# data space
xfs_io -f -c "falloc 0 192m" $mnt/subv/file &> /dev/null
rm $mnt/subv/file
sync
done
# Shouldn't fail after we removed the file
xfs_io -f -c "falloc 0 64m" $mnt/subv/file
[CAUSE]
Btrfs qgroup data reserve code allow multiple reservations to happen on
a single extent_changeset:
E.g:
btrfs_qgroup_reserve_data(inode, &data_reserved, 0, SZ_1M);
btrfs_qgroup_reserve_data(inode, &data_reserved, SZ_1M, SZ_2M);
btrfs_qgroup_reserve_data(inode, &data_reserved, 0, SZ_4M);
Btrfs qgroup code has its internal tracking to make sure we don't
double-reserve in above example.
The only pattern utilizing this feature is in the main while loop of
btrfs_fallocate() function.
However btrfs_qgroup_reserve_data()'s error handling has a bug in that
on error it clears all ranges in the io_tree with EXTENT_QGROUP_RESERVED
flag but doesn't free previously reserved bytes.
This bug has a two fold effect:
- Clearing EXTENT_QGROUP_RESERVED ranges
This is the correct behavior, but it prevents
btrfs_qgroup_check_reserved_leak() to catch the leakage as the
detector is purely EXTENT_QGROUP_RESERVED flag based.
- Leak the previously reserved data bytes.
The bug manifests when N calls to btrfs_qgroup_reserve_data are made and
the last one fails, leaking space reserved in the previous ones.
[FIX]
Also free previously reserved data bytes when btrfs_qgroup_reserve_data
fails.
Fixes: 524725537023 ("btrfs: qgroup: Introduce btrfs_qgroup_reserve_data function") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[BUG]
Under the following case with qgroup enabled, if some error happened
after we have reserved delalloc space, then in error handling path, we
could cause qgroup data space leakage:
From btrfs_truncate_block() in inode.c:
ret = btrfs_delalloc_reserve_space(inode, &data_reserved,
block_start, blocksize);
if (ret)
goto out;
[CAUSE]
In the above case, btrfs_delalloc_reserve_space() will call
btrfs_qgroup_reserve_data() and mark the io_tree range with
EXTENT_QGROUP_RESERVED flag.
In the error handling path, we have the following call stack:
btrfs_delalloc_release_space()
|- btrfs_free_reserved_data_space()
|- btrsf_qgroup_free_data()
|- __btrfs_qgroup_release_data(reserved=@reserved, free=1)
|- qgroup_free_reserved_data(reserved=@reserved)
|- clear_record_extent_bits();
|- freed += changeset.bytes_changed;
However due to a completion bug, qgroup_free_reserved_data() will clear
EXTENT_QGROUP_RESERVED flag in BTRFS_I(inode)->io_failure_tree, other
than the correct BTRFS_I(inode)->io_tree.
Since io_failure_tree is never marked with that flag,
btrfs_qgroup_free_data() will not free any data reserved space at all,
causing a leakage.
This type of error handling can only be triggered by errors outside of
qgroup code. So EDQUOT error from qgroup can't trigger it.
[FIX]
Fix the wrong target io_tree.
Reported-by: Josef Bacik <josef@toxicpanda.com> Fixes: bc42bda22345 ("btrfs: qgroup: Fix qgroup reserved space underflow by only freeing reserved ranges") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Before, if a eb failed to write out, we would end up triggering a
BUG_ON(). As of f4340622e0226 ("btrfs: extent_io: Move the BUG_ON() in
flush_write_bio() one level up"), we no longer BUG_ON(), so we should
make life consistent and add back the unwritten bytes to
dirty_metadata_bytes.
Fixes: f4340622e022 ("btrfs: extent_io: Move the BUG_ON() in flush_write_bio() one level up") CC: stable@vger.kernel.org # 5.2+ Reviewed-by: Filipe Manana <fdmanana@kernel.org> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When doing any form of incremental send the parent and the child trees
need to be compared via btrfs_compare_trees. This can result in long
loop chains without ever relinquishing the CPU. This causes softlockup
detector to trigger when comparing trees with a lot of items. Example
report:
At ctree.c:get_old_root(), we are accessing a root's header owner field
after we have freed the respective extent buffer. This results in an
use-after-free that can lead to crashes, and when CONFIG_DEBUG_PAGEALLOC
is set, results in a stack trace like the following:
Fix that by saving the root's header owner field into a local variable
before freeing the root's extent buffer, and then use that local variable
when needed.
Fixes: 30b0463a9394d9 ("Btrfs: fix accessing the root pointer in tree mod log functions") CC: stable@vger.kernel.org # 3.10+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Various notifications of type "BUG kmalloc-4096 () : Redzone
overwritten" have been observed recently in various parts of the kernel.
After some time, it has been made a relation with the use of BTRFS
filesystem and with SLUB_DEBUG turned on.
[ 22.809700] BUG kmalloc-4096 (Tainted: G W ): Redzone overwritten
Commit 69d2480456d1 ("btrfs: use copy_page for copying pages instead of
memcpy") changed the way bitmap blocks are copied. But allthough bitmaps
have the size of a page, they were allocated with kzalloc().
Most of the time, kzalloc() allocates aligned blocks of memory, so
copy_page() can be used. But when some debug options like SLAB_DEBUG are
activated, kzalloc() may return unaligned pointer.
On powerpc, memcpy(), copy_page() and other copying functions use
'dcbz' instruction which provides an entire zeroed cacheline to avoid
memory read when the intention is to overwrite a full line. Functions
like memcpy() are writen to care about partial cachelines at the start
and end of the destination, but copy_page() assumes it gets pages. As
pages are naturally cache aligned, copy_page() doesn't care about
partial lines. This means that when copy_page() is called with a
misaligned pointer, a few leading bytes are zeroed.
To fix it, allocate bitmaps through kmem_cache instead of using kzalloc()
The cache pool is created with PAGE_SIZE alignment constraint.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204371 Fixes: 69d2480456d1 ("btrfs: use copy_page for copying pages instead of memcpy") Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_free_space_bitmap ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When filtering xattr list for reading, presence of trusted xattr
results in a security audit log. However, if there is other content
no errno will be set, and if there isn't, the errno will be -ENODATA
and not -EPERM as is usually associated with a lack of capability.
The check does not block the request to list the xattrs present.
Switch to ns_capable_noaudit to reflect a more appropriate check.
Signed-off-by: Mark Salyzyn <salyzyn@android.com> Cc: linux-security-module@vger.kernel.org Cc: kernel-team@android.com Cc: stable@vger.kernel.org # v3.18+ Fixes: a082c6f680da ("ovl: filter trusted xattr for non-admin") Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We were not bumping up the "open on server" (num_remote_opens)
counter (in some cases) on opens of the share root so
could end up showing as a negative value.
CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
An earlier patch "CIFS: fix deadlock in cached root handling"
did not completely address the deadlock in open_shroot. This
patch addresses the deadlock.
In testing the recent patch:
smb3: improve handling of share deleted (and share recreated)
we were able to reproduce the open_shroot deadlock to one
of the target servers in unmount in a delete share scenario.
Fixes: 7e5a70ad88b1e ("CIFS: fix deadlock in cached root handling")
This is version 2 of this patch. An earlier version of this
patch "smb3: fix unmount hang in open_shroot" had a problem
found by Dan.
Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In some cases to work around server bugs or performance
problems it can be helpful to be able to disable requesting
SMB2.1/SMB3 leases on a particular mount (not to all servers
and all shares we are mounted to). Add new mount parm
"nolease" which turns off requesting leases on directory
or file opens. Currently the only way to disable leases is
globally through a module load parameter. This is more
granular.
Suggested-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bug is caused by the race between timeout handle and completion for
flush request.
When timeout handle function blk_mq_rq_timed_out() try to read
'req->q->mq_ops', the 'req' have completed and reinitiated by next
flush request, which would call blk_rq_init() to clear 'req' as 0.
After commit 12f5b93145 ("blk-mq: Remove generation seqeunce"),
normal requests lifetime are protected by refcount. Until 'rq->ref'
drop to zero, the request can really be free. Thus, these requests
cannot been reused before timeout handle finish.
However, flush request has defined .end_io and rq->end_io() is still
called even if 'rq->ref' doesn't drop to zero. After that, the 'flush_rq'
can be reused by the next flush request handle, resulting in null
pointer deference BUG ON.
We fix this problem by covering flush request with 'rq->ref'.
If the refcount is not zero, flush_end_io() return and wait the
last holder recall it. To record the request status, we add a new
entry 'rq_status', which will be used in flush_end_io().
Cc: Christoph Hellwig <hch@infradead.org> Cc: Keith Busch <keith.busch@intel.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: stable@vger.kernel.org # v4.18+ Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bob Liu <bob.liu@oracle.com> Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-------
v2:
- move rq_status from struct request to struct blk_flush_queue
v3:
- remove unnecessary '{}' pair.
v4:
- let spinlock to protect 'fq->rq_status'
v5:
- move rq_status after flush_running_idx member of struct blk_flush_queue Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 7211aef86f79 ("block: mq-deadline: Fix write completion
handling") added a call to blk_mq_sched_mark_restart_hctx() in
dd_dispatch_request() to make sure that write request dispatching does
not stall when all target zones are locked. This fix left a subtle race
when a write completion happens during a dispatch execution on another
CPU:
CPU 0: Dispatch CPU1: write completion
dd_dispatch_request()
lock(&dd->lock);
...
lock(&dd->zone_lock); dd_finish_request()
rq = find request lock(&dd->zone_lock);
unlock(&dd->zone_lock);
zone write unlock
unlock(&dd->zone_lock);
...
__blk_mq_free_request
check restart flag (not set)
-> queue not run
...
if (!rq && have writes)
blk_mq_sched_mark_restart_hctx()
unlock(&dd->lock)
Since the dispatch context finishes after the write request completion
handling, marking the queue as needing a restart is not seen from
__blk_mq_free_request() and blk_mq_sched_restart() not executed leading
to the dispatch stall under 100% write workloads.
Fix this by moving the call to blk_mq_sched_mark_restart_hctx() from
dd_dispatch_request() into dd_finish_request() under the zone lock to
ensure full mutual exclusion between write request dispatch selection
and zone unlock on write request completion.
Fixes: 7211aef86f79 ("block: mq-deadline: Fix write completion handling") Cc: stable@vger.kernel.org Reported-by: Hans Holmberg <Hans.Holmberg@wdc.com> Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Investigation revealed a race where pf->vf[vsi->vf_id].trusted may get
accessed by the watchdog via i40e_sync_filters_subtask() although
i40e_free_vfs() already free'd pf->vf.
To avoid this the call to i40e_sync_vsi_filters() in
i40e_sync_filters_subtask() needs to be guarded by __I40E_VF_DISABLE,
which is also used by i40e_free_vfs().
Note: put the __I40E_VF_DISABLE check after the
__I40E_MACVLAN_SYNC_PENDING check as the latter is more likely to
trigger.
CC: stable@vger.kernel.org Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2ec ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Fixes: 13104929d2ec ("ath10k: fill the channel survey results for WCN3990 correctly") Cc: stable@vger.kernel.org # 5.0 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 0b6cf6b97b7e ("tpm: pass an array of tpm_extend_digest structures to
tpm_pcr_extend()") modifies tpm_pcr_extend() to accept a digest for each
PCR bank. After modification, tpm_pcr_extend() expects that digests are
passed in the same order as the algorithms set in chip->allocated_banks.
This patch fixes two issues introduced in the last iterations of the patch
set: missing initialization of the TPM algorithm ID in the tpm_digest
structures passed to tpm_pcr_extend() by the trusted key module, and
unreleased locks in the TPM driver due to returning from tpm_pcr_extend()
without calling tpm_put_ops().
Cc: stable@vger.kernel.org Fixes: 0b6cf6b97b7e ("tpm: pass an array of tpm_extend_digest structures to tpm_pcr_extend()") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Tetsuo then noticed that this is because the __memcg_kmem_charge_memcg
fails __GFP_NOFAIL charge when the kmem limit is reached. This is a wrong
behavior because nofail allocations are not allowed to fail. Normal
charge path simply forces the charge even if that means to cross the
limit. Kmem accounting should be doing the same.
Link: http://lkml.kernel.org/r/20190906125608.32129-1-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com> Debugged-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Thomas Lindroth <thomas.lindroth@gmail.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Masoud Sharbiani noticed that commit 29ef680ae7c21110 ("memcg, oom: move
out_of_memory back to the charge path") broke memcg OOM called from
__xfs_filemap_fault() path. It turned out that try_charge() is retrying
forever without making forward progress because mem_cgroup_oom(GFP_NOFS)
cannot invoke the OOM killer due to commit 3da88fb3bacfaa33 ("mm, oom:
move GFP_NOFS check to out_of_memory").
Allowing forced charge due to being unable to invoke memcg OOM killer will
lead to global OOM situation. Also, just returning -ENOMEM will be risky
because OOM path is lost and some paths (e.g. get_user_pages()) will leak
-ENOMEM. Therefore, invoking memcg OOM killer (despite GFP_NOFS) will be
the only choice we can choose for now.
Until 29ef680ae7c21110, we were able to invoke memcg OOM killer when
GFP_KERNEL reclaim failed [1]. But since 29ef680ae7c21110, we need to
invoke memcg OOM killer when GFP_NOFS reclaim failed [2]. Although in the
past we did invoke memcg OOM killer for GFP_NOFS [3], we might get
pre-mature memcg OOM reports due to this patch.
total_{migrate,free}_scanned will be added to COMPACTMIGRATE_SCANNED and
COMPACTFREE_SCANNED in compact_zone(). We should clear them before
scanning a new zone. In the proc triggered compaction, we forgot clearing
them.
[laoar.shao@gmail.com: introduce a helper compact_zone_counters_init()] Link: http://lkml.kernel.org/r/1563869295-25748-1-git-send-email-laoar.shao@gmail.com
[akpm@linux-foundation.org: expand compact_zone_counters_init() into its single callsite, per mhocko]
[vbabka@suse.cz: squash compact_zone() list_head init as well] Link: http://lkml.kernel.org/r/1fb6f7da-f776-9e42-22f8-bbb79b030b98@suse.cz
[akpm@linux-foundation.org: kcompactd_do_work(): avoid unnecessary initialization of cc.zone] Link: http://lkml.kernel.org/r/1563789275-9639-1-git-send-email-laoar.shao@gmail.com Fixes: 7f354a548d1c ("mm, compaction: add vmstats for kcompactd work") Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: Yafang Shao <shaoyafang@didiglobal.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently there is a leak in init_z3fold_page() -- it allocates handles
from kmem cache even for headless pages, but then they are never used and
never freed, so eventually kmem cache may get exhausted. This patch
provides a fix for that.
Link: http://lkml.kernel.org/r/20190917185352.44cf285d3ebd9e64548de5de@gmail.com Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Reported-by: Markus Linnala <markus.linnala@gmail.com> Tested-by: Markus Linnala <markus.linnala@gmail.com> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Henry Burns <henrywolfeburns@gmail.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
z3fold_page_reclaim()'s retry mechanism is broken: on a second iteration
it will have zhdr from the first one so that zhdr is no longer in line
with struct page. That leads to crashes when the system is stressed.
Fix that by moving zhdr assignment up.
While at it, protect against using already freed handles by using own
local slots structure in z3fold_page_reclaim().
Link: http://lkml.kernel.org/r/20190908162919.830388dc7404d1e2c80f4095@gmail.com Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Reported-by: Markus Linnala <markus.linnala@gmail.com> Reported-by: Chris Murphy <bugzilla@colorremedies.com> Reported-by: Agustin Dall'Alba <agustin@dallalba.com.ar> Cc: "Maciej S. Szmigiero" <mail@maciej.szmigiero.name> Cc: Shakeel Butt <shakeelb@google.com> Cc: Henry Burns <henrywolfeburns@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In function sweep_bh_for_rgrps, which is a helper for punch_hole,
it uses variable buf_in_tr to keep track of when it needs to commit
pending block frees on a partial delete that overflows the
transaction created for the delete. The problem is that the
variable was initialized at the start of function sweep_bh_for_rgrps
but it was never cleared, even when starting a new transaction.
This patch reinitializes the variable when the transaction is
ended, so the next transaction starts out with it cleared.
Fixes: d552a2b9b33e ("GFS2: Non-recursive delete") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
For various reasons, at least with x86 EFI firmwares, the xoffset and
yoffset in the BGRT info are not always reliable.
Extensive testing has shown that when the info is correct, the
BGRT image is always exactly centered horizontally (the yoffset variable
is more variable and not always predictable).
This commit simplifies / improves the bgrt_sanity_check to simply
check that the BGRT image is exactly centered horizontally and skips
(re)drawing it when it is not.
This fixes the BGRT image sometimes being drawn in the wrong place.
Cc: stable@vger.kernel.org Fixes: 88fe4ceb2447 ("efifb: BGRT: Do not copy the boot graphics for non native resolutions") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: Peter Jones <pjones@redhat.com>, Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190721131918.10115-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Tested-by: Lee Jones <lee.jones@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
set_msi_sid_cb() is used to determine whether device aliases share the
same bus, but it can provide false indications that aliases use the same
bus when in fact they do not. The reason is that set_msi_sid_cb()
assumes that pdev is fixed, while actually pci_for_each_dma_alias() can
call fn() when pdev is set to a subordinate device.
As a result, running an VM on ESX with VT-d emulation enabled can
results in the log warning such as:
DMAR: [INTR-REMAP] Request device [00:11.0] fault index 3b [fault reason 38] Blocked an interrupt request due to source-id verification failure
This seems to cause additional ata errors such as:
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
These timeouts also cause boot to be much longer and other errors.
Fix it by checking comparing the alias with the previous one instead.
Fixes: 3f0c625c6ae71 ("iommu/vt-d: Allow interrupts from the entire bus for aliased devices") Cc: stable@vger.kernel.org Cc: Logan Gunthorpe <logang@deltatee.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Joerg Roedel <joro@8bytes.org> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Nadav Amit <namit@vmware.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ENOTSUPP is not supposed to be returned to userspace. This was found on an
OpenPower machine, where the RTC does not support set_alarm.
On that system, a clock_nanosleep(CLOCK_REALTIME_ALARM, ...) results in
"524 Unknown error 524"
Replace it with EOPNOTSUPP which results in the expected "95 Operation not
supported" error.
Fixes: 1c6b39ad3f01 (alarmtimers: Return -ENOTSUPP if no RTC device is present) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190903171802.28314-1-cascardo@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Detecting the ATS capability of the SMMU at probe time introduces a
spinlock into the ->unmap() fast path, even when ATS is not actually
in use. Furthermore, the ATC invalidation that exists is broken, as it
occurs before invalidation of the main SMMU TLB which leaves a window
where the ATC can be repopulated with stale entries.
Given that ATS is both a new feature and a specialist sport, disable it
for now whilst we fix it properly in subsequent patches. Since PRI
requires ATS, disable that too.
Cc: <stable@vger.kernel.org> Fixes: 9ce27afc0830 ("iommu/arm-smmu-v3: Add support for PCI ATS") Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
150MHz is a fundamental limitation of RK3328 Soc, w/o this limitation,
eMMC, for instance, will run into 200MHz clock rate in HS200 mode, which
makes the RK3328 boards not always boot properly. By adding it in
rk3328.dtsi would also obviate the worry of missing it when adding new
boards.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs") Cc: stable@vger.kernel.org Cc: Robin Murphy <robin.murphy@arm.com> Cc: Liang Chen <cl@rock-chips.com> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
05f2d2f83b5a ("arm64: tlbflush: Introduce __flush_tlb_kernel_pgtable")
added a new TLB invalidation helper which is used when freeing
intermediate levels of page table used for kernel mappings, but is
missing the required ISB instruction after completion of the TLBI
instruction.
Add the missing barrier.
Cc: <stable@vger.kernel.org> Fixes: 05f2d2f83b5a ("arm64: tlbflush: Introduce __flush_tlb_kernel_pgtable") Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This fixes a kernel panic on memcpy when
FORTIFY_SOURCE is enabled.
The initial smp implementation on commit aa7eb2bb4e4a
("arm: zynq: Add smp support")
used memcpy, which worked fine until commit ee333554fed5
("ARM: 8749/1: Kconfig: Add ARCH_HAS_FORTIFY_SOURCE")
enabled overflow checks at runtime, producing a read
overflow panic.
As reported by erofs-utils fuzzer, unsupported compressed
clustersize will make fill_inode_lazy fail, for such case
we cannot set EROFS_V_Z_INITED_BIT since we need return
failure for each z_erofs_map_blocks_iter().
When brk was moved for binaries without an interpreter, it should have
been limited to ET_DYN only. In other words, the special case was an
ET_DYN that lacks an INTERP, not just an executable that lacks INTERP.
The bug manifested for giant static executables, where the brk would end
up in the middle of the text area on 32-bit architectures.
Reported-and-tested-by: Richard Kojedzinszky <richard@kojedz.in> Fixes: bbdc6076d2e5 ("binfmt_elf: move brk out of mmap when doing direct loader exec") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The DSPI interrupt can be shared between two controllers at least on the
LX2160A. In that case, the driver for one controller might misbehave and
consume the other's interrupt. Fix this by actually checking if any of
the bits in the status register have been asserted.
Fixes: 13aed2392741 ("spi: spi-fsl-dspi: use IRQF_SHARED mode to request IRQ") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20190822212450.21420-2-olteanv@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The actual device name of the SPI controller being registered on EP93xx is
"spi0" (as seen by gpiod_find_lookup_table()). This patch fixes all
relevant lookup tables and the following failure (seen on EDB9302):
ep93xx-spi ep93xx-spi.0: failed to register SPI master
ep93xx-spi: probe of ep93xx-spi.0 failed with error -22
Fixes: 1dfbf334f1236 ("spi: ep93xx: Convert to use CS GPIO descriptors") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Link: https://lore.kernel.org/r/20190831180402.10008-1-alexander.sverdlin@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add an extra condition to add the video output control class when the
device has some hdmi outputs defined. This is required to then always
be able to add the display present control, which is enabled when
there are some hdmi outputs.
This fixes the corner case where no_error_inj is enabled and the
device has no frame buffer but some hdmi outputs, as otherwise the
video output control class would be added anyway. Without this fix,
the sanity checks fail in v4l2_ctrl_new() as name is NULL.
Fixes: c533435ffb91 ("media: vivid: add display present control") Cc: stable@vger.kernel.org # for 5.3 Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A bugfix introduce a link failure in configurations without CONFIG_MODULES:
In file included from drivers/media/usb/dvb-usb/pctv452e.c:20:0:
drivers/media/usb/dvb-usb/pctv452e.c: In function 'pctv452e_frontend_attach':
drivers/media/dvb-frontends/stb0899_drv.h:151:36: error: weak declaration of 'stb0899_attach' being applied to a already existing, static definition
The problem is that the !IS_REACHABLE() declaration of stb0899_attach()
is a 'static inline' definition that clashes with the weak definition.
I further observed that the bugfix was only done for one of the five users
of stb0899_attach(), the other four still have the problem. This reverts
the bugfix and instead addresses the problem by not dropping the reference
count when calling '->detach()', instead we call this function directly
in dvb_frontend_put() before dropping the kref on the front-end.
I first submitted this in early 2018, and after some discussion it
was apparently discarded. While there is a long-term plan in place,
that plan is obviously not nearing completion yet, and the current
kernel is still broken unless this patch is applied.
Link: https://patchwork.kernel.org/patch/10140175/ Link: https://patchwork.linuxtv.org/patch/54831/ Cc: Max Kellermann <max.kellermann@gmail.com> Cc: Wolfgang Rohdewald <wolfgang@rohdewald.de> Cc: stable@vger.kernel.org Fixes: f686c14364ad ("[media] stb0899: move code to "detach" callback") Fixes: 6cdeaed3b142 ("media: dvb_usb_pctv452e: module refcount changes were unbalanced") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Hantro codec is typically used in platforms with an IOMMU,
so we need to set a proper DMA segment size. Devices without an
IOMMU will still fallback to default 64KiB segments.
poll_wait uses &buf->done, but buf is NULL. Move the poll_wait to later
in the function once buf is correctly set and only call it if it is
non-NULL.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: bb436cbeb918 ("media: videobuf: fix epoll() by calling poll_wait first") Cc: <stable@vger.kernel.org> # for v5.1 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use the fast invalidate mechasim to zap MMIO sptes on a MMIO generation
wrap. The fast invalidate flow was reintroduced to fix a livelock bug
in kvm_mmu_zap_all() that can occur if kvm_mmu_zap_all() is invoked when
the guest has live vCPUs. I.e. using kvm_mmu_zap_all() to handle the
MMIO generation wrap is theoretically susceptible to the livelock bug.
This effectively reverts commit 4771450c345dc ("Revert "KVM: MMU: drop
kvm_mmu_zap_mmio_sptes""), i.e. restores the behavior of commit a8eca9dcc656a ("KVM: MMU: drop kvm_mmu_zap_mmio_sptes").
Note, this actually fixes commit 571c5af06e303 ("KVM: x86/mmu:
Voluntarily reschedule as needed when zapping MMIO sptes"), but there
is no need to incrementally revert back to using fast invalidate, e.g.
doing so doesn't provide any bisection or stability benefits.
Fixes: 571c5af06e303 ("KVM: x86/mmu: Voluntarily reschedule as needed when zapping MMIO sptes") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We can easily route hardware interrupts directly into VM context when
they target the "Fixed" or "LowPriority" delivery modes.
However, on modes such as "SMI" or "Init", we need to go via KVM code
to actually put the vCPU into a different mode of operation, so we can
not post the interrupt
Add code in the VMX and SVM PI logic to explicitly refuse to establish
posted mappings for advanced IRQ deliver modes. This reflects the logic
in __apic_accept_irq() which also only ever passes Fixed and LowPriority
interrupts as posted interrupts into the guest.
This fixes a bug I have with code which configures real hardware to
inject virtual SMIs into my guest.
Signed-off-by: Alexander Graf <graf@amazon.com> Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Wanpeng Li <wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Manually generate the PDPTR reserved bit mask when explicitly loading
PDPTRs. The reserved bits that are being tracked by the MMU reflect the
current paging mode, which is unlikely to be PAE paging in the vast
majority of flows that use load_pdptrs(), e.g. CR0 and CR4 emulation,
__set_sregs(), etc... This can cause KVM to incorrectly signal a bad
PDPTR, or more likely, miss a reserved bit check and subsequently fail
a VM-Enter due to a bad VMCS.GUEST_PDPTR.
Add a one off helper to generate the reserved bits instead of sharing
code across the MMU's calculations and the PDPTR emulation. The PDPTR
reserved bits are basically set in stone, and pushing a helper into
the MMU's calculation adds unnecessary complexity without improving
readability.
Oppurtunistically fix/update the comment for load_pdptrs().
Note, the buggy commit also introduced a deliberate functional change,
"Also remove bit 5-6 from rsvd_bits_mask per latest SDM.", which was
effectively (and correctly) reverted by commit cd9ae5fe47df ("KVM: x86:
Fix page-tables reserved bits"). A bit of SDM archaeology shows that
the SDM from late 2008 had a bug (likely a copy+paste error) where it
listed bits 6:5 as AVL and A for PDPTEs used for 4k entries but reserved
for 2mb entries. I.e. the SDM contradicted itself, and bits 6:5 are and
always have been reserved.
Fixes: 20c466b56168d ("KVM: Use rsvd_bits_mask in load_pdptrs()") Cc: stable@vger.kernel.org Cc: Nadav Amit <nadav.amit@gmail.com> Reported-by: Doug Reiland <doug.reiland@intel.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
x86_emulate_instruction() takes into account ctxt->have_exception flag
during instruction decoding, but in practice this flag is never set in
x86_decode_insn().
Fixes: 6ea6e84309ca ("KVM: x86: inject exceptions produced by x86_decode_insn") Cc: stable@vger.kernel.org Cc: Denis Lunev <den@virtuozzo.com> Cc: Roman Kagan <rkagan@virtuozzo.com> Cc: Denis Plotnikov <dplotnikov@virtuozzo.com> Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
inject_emulated_exception() returns true if and only if nested page
fault happens. However, page fault can come from guest page tables
walk, either nested or not nested. In both cases we should stop an
attempt to read under RIP and give guest to step over its own page
fault handler.
This is also visible when an emulated instruction causes a #GP fault
and the VMware backdoor is enabled. To handle the VMware backdoor,
KVM intercepts #GP faults; with only the next patch applied,
x86_emulate_instruction() injects a #GP but returns EMULATE_FAIL
instead of EMULATE_DONE. EMULATE_FAIL causes handle_exception_nmi()
(or gp_interception() for SVM) to re-inject the original #GP because it
thinks emulation failed due to a non-VMware opcode. This patch prevents
the issue as x86_emulate_instruction() will return EMULATE_DONE after
injecting the #GP.
Fixes: 6ea6e84309ca ("KVM: x86: inject exceptions produced by x86_decode_insn") Cc: stable@vger.kernel.org Cc: Denis Lunev <den@virtuozzo.com> Cc: Roman Kagan <rkagan@virtuozzo.com> Cc: Denis Plotnikov <dplotnikov@virtuozzo.com> Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 871f1f2bcb01 ("platform/x86: intel_int0002_vgpio: Only implement
irq_set_wake on Bay Trail") removed the irq_set_wake method from the
struct irq_chip used on Cherry Trail, but it did not set
IRQCHIP_SKIP_SET_WAKE causing kernel/irq/manage.c: set_irq_wake_real()
to return -ENXIO.
This causes the kernel to no longer see PME events reported through the
INT0002 device as wakeup events. Which e.g. breaks wakeup by the (USB)
keyboard on many Cherry Trail 2-in-1 devices.
Cc: stable@vger.kernel.org Fixes: 871f1f2bcb01 ("platform/x86: intel_int0002_vgpio: Only implement irq_set_wake on Bay Trail") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The HP Dino PCI controller chip can be used in two variants: as on-board
controller (e.g. in B160L), or on an Add-On card ("Card-Mode") to bridge
PCI components to systems without a PCI bus, e.g. to a HSC/GSC bus. One
such Add-On card is the HP HSC-PCI Card which has one or more DEC Tulip
PCI NIC chips connected to the on-card Dino PCI controller.
Dino in Card-Mode has a big disadvantage: All PCI memory accesses need
to go through the DINO_MEM_DATA register, so Linux drivers will not be
able to use the ioremap() function. Without ioremap() many drivers will
not work, one example is the tulip driver which then simply crashes the
kernel if it tries to access the ports on the HP HSC card.
This patch disables the HP HSC card if it finds one, and as such
fixes the kernel crash on a HP D350/2 machine.
Signed-off-by: Helge Deller <deller@gmx.de> Noticed-by: Phil Scarr <phil.scarr@pm.me> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It's in fuse_parse_cache(). %rbx (ffff88859367bff0) is fuse_dirent
pointer - addr + offset. FUSE_DIRENT_SIZE() is trying to dereference
namelen off of it but that derefs into the next page which is disabled
by pagealloc debug causing a PF.
This is caused by dirent->namelen being accessed before ensuring that
there's enough bytes in the page for the dirent. Fix it by pushing
down reclen calculation.
Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 5d7bc7e8680c ("fuse: allow using readdir cache") Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When IOCB_CMD_POLL is used on the FUSE device, aio_poll() disables IRQs
and takes kioctx::ctx_lock, then fuse_iqueue::waitq.lock.
This may have to wait for fuse_iqueue::waitq.lock to be released by one
of many places that take it with IRQs enabled. Since the IRQ handler
may take kioctx::ctx_lock, lockdep reports that a deadlock is possible.
Fix it by protecting the state of struct fuse_iqueue with a separate
spinlock, and only accessing fuse_iqueue::waitq using the versions of
the waitqueue functions which do IRQ-safe locking internally.
=====================================================
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.3.0-rc5 #9 Not tainted
-----------------------------------------------------
syz_fuse/135 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: 000000003590ceda (&fiq->waitq){+.+.}, at: spin_lock include/linux/spinlock.h:338 [inline] 000000003590ceda (&fiq->waitq){+.+.}, at: aio_poll fs/aio.c:1751 [inline] 000000003590ceda (&fiq->waitq){+.+.}, at: __io_submit_one.constprop.0+0x203/0x5b0 fs/aio.c:1825
and this task is already holding: 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:363 [inline] 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1749 [inline] 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one.constprop.0+0x1f4/0x5b0 fs/aio.c:1825
which would create a new lock dependency:
(&(&ctx->ctx_lock)->rlock){..-.} -> (&fiq->waitq){+.+.}
but this new dependency connects a SOFTIRQ-irq-safe lock:
(&(&ctx->ctx_lock)->rlock){..-.}
[...]
Reported-by: syzbot+af05535bb79520f95431@syzkaller.appspotmail.com Reported-by: syzbot+d86c4426a01f60feddc7@syzkaller.appspotmail.com Fixes: bfe4037e722e ("aio: implement IOCB_CMD_POLL") Cc: <stable@vger.kernel.org> # v4.19+ Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
tpm_send() does not give anymore the result back to the caller. This
would require another memcpy(), which kind of tells that the whole
approach is somewhat broken. Instead, as Mimi suggested, this commit
just wraps the data to the tpm_buf, and thus the result will not go to
the garbage.
Obviously this assumes from the caller that it passes large enough
buffer, which makes the whole API somewhat broken because it could be
different size than @buflen but since trusted keys is the only module
using this API right now I think that this fix is sufficient for the
moment.
In the near future the plan is to replace the parameters with a tpm_buf
created by the caller.
Reported-by: Mimi Zohar <zohar@linux.ibm.com> Suggested-by: Mimi Zohar <zohar@linux.ibm.com> Cc: stable@vger.kernel.org Fixes: 412eb585587a ("use tpm_buf in tpm_transmit_cmd() as the IO parameter") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The tpm_tis_core has to set the TPM_CHIP_FLAG_IRQ before probing for
interrupts since there is no other place in the code that would set
it.
Cc: linux-stable@vger.kernel.org Fixes: 570a36097f30 ("tpm: drop 'irq' from struct tpm_vendor_specific") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The interrupt probing sequence in tpm_tis_core cannot obviously run with
the TPM power gated. Power on the TPM with tpm_chip_start() before
probing IRQ's. Turn it off once the probing is complete.
Cc: linux-stable@vger.kernel.org Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit <684d984038aa> ('powerpc/powernv: Add debugfs interface for
imc-mode and imc') added debugfs interface for the nest imc pmu
devices to support changing of different ucode modes. Primarily adding
this capability for debug. But when doing so, the code did not
consider the case of cpu-less nodes. So when reading the _cmd_ or
_mode_ file of a cpu-less node will create this crash.
After patch, ls output for the debugfs imc directory
# ls /sys/kernel/debug/powerpc/imc/
imc_cmd_0 imc_cmd_8 imc_mode_0 imc_mode_8
Actual bug here is that, we have two loops with potentially different
loop counts. That is, in imc_get_mem_addr_nest(), loop count is
obtained from the dt entries. But in case of export_imc_mode_and_cmd(),
loop was based on for_each_nid() count. Patch fixes the loop count in
latter based on the struct mem_info. Ideally it would be better to
have array size in struct imc_pmu.
Fixes: 684d984038aa ('powerpc/powernv: Add debugfs interface for imc-mode and imc') Reported-by: Qian Cai <cai@lca.pw> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190827101635.6942-1-maddy@linux.vnet.ibm.com Cc: Jan Stancek <jstancek@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Implement .cleanup_rq() callback for freeing driver private part
of the request. Then we can avoid to leak this part if the request isn't
completed by SCSI, and freed by blk-mq or upper layer(such as dm-rq) finally.
Cc: Ewan D. Milne <emilne@redhat.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Hannes Reinecke <hare@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mike Snitzer <snitzer@redhat.com> Cc: dm-devel@redhat.com Cc: <stable@vger.kernel.org> Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
SCSI maintains its own driver private data hooked off of each SCSI
request, and the pridate data won't be freed after scsi_queue_rq()
returns BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE. An upper layer driver
(e.g. dm-rq) may need to retry these SCSI requests, before SCSI has
fully dispatched them, due to a lower level SCSI driver's resource
limitation identified in scsi_queue_rq(). Currently SCSI's per-request
private data is leaked when the upper layer driver (dm-rq) frees and
then retries these requests in response to BLK_STS_RESOURCE or
BLK_STS_DEV_RESOURCE returns from scsi_queue_rq().
This usecase is so specialized that it doesn't warrant training an
existing blk-mq interface (e.g. blk_mq_free_request) to allow SCSI to
account for freeing its driver private data -- doing so would add an
extra branch for handling a special case that all other consumers of
SCSI (and blk-mq) won't ever need to worry about.
So the most pragmatic way forward is to delegate freeing SCSI driver
private data to the upper layer driver (dm-rq). Do so by adding
new .cleanup_rq callback and calling a new blk_mq_cleanup_rq() method
from dm-rq. A following commit will implement the .cleanup_rq() hook
in scsi_mq_ops.
Cc: Ewan D. Milne <emilne@redhat.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Hannes Reinecke <hare@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mike Snitzer <snitzer@redhat.com> Cc: dm-devel@redhat.com Cc: <stable@vger.kernel.org> Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The laptop has a combined jack to attach headsets on the right.
The BIOS encodes them as two different colored jacks at the front,
but otherwise it seems to be configured ok. But any adaption of
the pins config on its own doesn't fix the jack detection to work
in Linux. Still Windows works correct.
This is somehow fixed by chaining ALC256_FIXUP_ASUS_HEADSET_MODE,
which seems to register the microphone jack as a headset part and
also results in fixing jack sensing, visible in dmesg as:
[ Actually the essential change is the location of the jack; the
driver created "Front Mic Jack" without the matching volume / mute
control element due to its jack location, which confused PA.
-- tiwai ]
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/8f4f9b20-0aeb-f8f1-c02f-fd53c09679f1@fbihome.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A rather embarrasing mistake had us call sched_setscheduler() before
initializing the parameters passed to it.
Fixes: 1a763fd7c633 ("rcu/tree: Call setschedule() gp ktread to SCHED_FIFO outside of atomic region") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A previous commit removed the panel-dpi driver, which made the
video on the AM3517-evm stop working because it relied on the dpi
driver for setting video timings. Now that the simple-panel driver
is available in omap2plus, this patch migrates the am3517-evm
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While no uses in the kernel triggered this case, it was possible to have
a false negative where a struct contains other structs which contain only
function pointers because of unreachable code in is_pure_ops_struct().
Signed-off-by: Joonwon Kang <kjw1627@gmail.com> Link: https://lore.kernel.org/r/20190727155841.GA13586@host Fixes: 313dd1b62921 ("gcc-plugins: Add the randstruct plugin") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-eoan-kernel.git / log