Merge tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: Changes for v5.4 merge window
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
usb: gadget: net2280: Add workaround for AB chip Errata 11
usb: gadget: net2280: Move all "ll" registers in one structure
usb: dwc3: gadget: Workaround Mirosoft's BESL check
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb: cdns3: Add Cadence USB3 DRD Driver
usb: common: Simplify usb_decode_get_set_descriptor function.
usb: common: Patch simplify usb_decode_set_clear_feature function.
usb: common: Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: gadget: composite: Set recommended BESL values
usb: dwc3: gadget: Set BESL config parameter
usb: dwc3: Separate field holding multiple properties
usb: gadget: Export recommended BESL values
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
usb: udc: lpc32xx: silence fall-through warning
usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
usb: udc: lpc32xx: remove set but not used 3 variables
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
usb: dwc3: st: Add of_dev_put() in probe function
usb: dwc3: st: Add of_node_put() before return in probe function
...
usb: gadget: net2280: Add workaround for AB chip Errata 11
The errata description is:
Workaround for Default Duration of LFPS Handshake Signaling for
Device-Initiated U1 Exit is too short.
The default duration of the LFPS handshake generated by USB3380 for a device-initiated U1-exit may not be
long enough for certain SuperSpeed downstream ports (SuperSpeed hubs/hosts) to recognize. This could lead
to USB3380 entering the recovery state pre-maturely and ending up in the SS.Inactive state.
I have observed various enumeration failures, seemingly related to
lost transactions or SETUP status phases on modern hosts (typically
thunderbolt capable systems) without this workaround.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: net2280: Move all "ll" registers in one structure
The split into multiple structures of the "ll" register bank is
impractical. It makes it hard to add ll_lfps_timers_2 which is
at offset 0x794, which is outside of the existing "lfps" structure
and would require us to add yet another one.
Instead, move all the "ll" registers into a single usb338x_ll_regs
structure, and add ll_lfps_timers_2 while at it. It will be used
in a subsequent patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
While testing our host system using Microsoft's usb stack against our
gadget for various BESL values, we found an issue with their usb stack
when the recommended baseline BESL value is 0 (125us) or when the deep
BESL is 1 or less. The Windows host will issue a usb reset immediately
after it receives the extended BOS descriptor and the enumeration will
fail after a few attempts.
To keep compatibility with Microsoft's host usb stack, let's workaround
this issue by using the recommended baseline BESL of 1 (or 150us)
and clamp the deep BESL value within 2 to 15.
This was tested against Windows 10 build 18956.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pawel Laszczak [Mon, 26 Aug 2019 11:19:31 +0000 (12:19 +0100)]
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.
Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.
To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.
The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.
Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.
Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.
Issue has been fixed for DEV_VER_V2 version of controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pawel Laszczak [Mon, 26 Aug 2019 11:19:30 +0000 (12:19 +0100)]
usb: cdns3: Add Cadence USB3 DRD Driver
This patch introduce new Cadence USBSS DRD driver to Linux kernel.
The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch adds usb_decode_test_mode and usb_decode_device_feature functions,
which allow to make more readable and simplify the
usb_decode_set_clear_feature function.
Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pawel Laszczak [Mon, 26 Aug 2019 11:19:27 +0000 (12:19 +0100)]
usb: common: Separated decoding functions from dwc3 driver.
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/common/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/ch9.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Thinh Nguyen [Tue, 20 Aug 2019 01:36:12 +0000 (18:36 -0700)]
usb: gadget: composite: Set recommended BESL values
Set the recommended BESL deep and baseline values based on the gadget's
configuration parameters to the extended BOS descriptor. This feature
helps to optimize power savings by maximizing the opportunity for longer
L1 residency time.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Thinh Nguyen [Tue, 20 Aug 2019 01:36:06 +0000 (18:36 -0700)]
usb: dwc3: gadget: Set BESL config parameter
When operating with LPM signals, the controller asserts the deep
low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of
the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and
with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal
(utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the
controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL
to 0 for the shallow low-power signal. This maximizes the opportunity
for L1 residency and optimizes power savings.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Thinh Nguyen [Tue, 20 Aug 2019 01:35:58 +0000 (18:35 -0700)]
usb: dwc3: Separate field holding multiple properties
dwc->hird_threshold field should store "snps,hird_threshold" property
only and not a combination of multiple properties. Remove the value of
"snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Thinh Nguyen [Tue, 20 Aug 2019 01:35:47 +0000 (18:35 -0700)]
usb: gadget: Export recommended BESL values
Currently there's no option for the controller driver to report the
recommended Best Effort Service Latency (BESL) when operating with LPM
support. Add new fields in usb_dcd_config_params to export the
recommended baseline and deep BESL values for the function drivers to
set the proper BESL value in the BOS descriptor.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nishka Dasgupta [Mon, 19 Aug 2019 07:42:34 +0000 (13:12 +0530)]
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
Static structure fsl_otg_initdata, of type fsl_otg_config, is used only
once, when the value of its field otg_port is assigned to another
variable. As fsl_otg_initdata.otg_port is of type u8, any changes to
its copy do not affect the original, and fsl_otg_initdata itself is
never modified. Hence make fsl_otg_initdata constant to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mao Wenan [Thu, 22 Aug 2019 07:05:57 +0000 (15:05 +0800)]
usb: udc: lpc32xx: remove set but not used 3 variables
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_protocol_cmd_r’:
drivers/usb/gadget/udc/lpc32xx_udc.c:744:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_dma_ep’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1994:14: warning: variable ‘epstatus’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_ep0_setup’:
drivers/usb/gadget/udc/lpc32xx_udc.c:2200:22: warning: variable ‘wLength’ set but not used [-Wunused-but-set-variable]
It is not used since commit 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Roger Quadros [Thu, 22 Aug 2019 13:40:28 +0000 (16:40 +0300)]
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
If a gadget driver is in the pending drivers list, a UDC
becomes available and udc_bind_to_driver() fails, then it
gets deleted from the pending list.
i.e. list_del(&driver->pending) in check_pending_gadget_drivers().
Then if that gadget driver is unregistered,
usb_gadget_unregister_driver() does a list_del(&driver->pending)
again thus causing a page fault as that list entry has been poisoned
by the previous list_del().
Fix this by using list_del_init() instead of list_del() in
check_pending_gadget_drivers().
Test case:
- Make sure no UDC is available
- modprobe g_mass_storage file=wrongfile
- Load UDC driver so it becomes available
lun0: unable to open backing file: wrongfile
- modprobe -r g_mass_storage
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nishka Dasgupta [Mon, 19 Aug 2019 07:24:36 +0000 (12:54 +0530)]
usb: dwc3: st: Add of_dev_put() in probe function
In function st_dwc3_probe, variable child_pdev takes the value returned
by of_find_device_by_node, which gets a device pointer but does not put
it. If child_pdev is not put before the probe function returns, it may
cause a reference leak. Hence put child_pdev after its last usage.
Issue found with Coccinelle.
Nishka Dasgupta [Mon, 19 Aug 2019 07:24:35 +0000 (12:54 +0530)]
usb: dwc3: st: Add of_node_put() before return in probe function
The local variable child in the function st_dwc3_probe takes the return
value of of_get_child_by_name, which gets a node and does not put it. If
the function returns without releasing child, this could cause a memory
error. Hence put child as soon as there is no more use for it. Also
create a new label, err_node_put, just before label undo_softreset; so
that err_node_put puts child. In between initialisation of child and its
first put, modify all statements that go to undo_softreset to now go to
err_node_put instead, from where they can fall through to
undo_softreset.
Issue found with Coccinelle.
Roger Quadros [Mon, 26 Aug 2019 13:10:58 +0000 (16:10 +0300)]
usb: dwc3: don't set gadget->is_otg flag
This reverts
commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
driver core: initialize a default DMA mask for platform device
We still treat devices without a DMA mask as defaulting to 32-bits for
both mask, but a few releases ago we've started warning about such
cases, as they require special cases to work around this sloppyness.
Add a dma_mask field to struct platform_device so that we can initialize
the dma_mask pointer in struct device and initialize both masks to
32-bits by default, replacing similar functionality in m68k and
powerpc. The arch_setup_pdev_archdata hooks is now unused and removed.
Note that the code looks a little odd with the various conditionals
because we have to support platform_device structures that are
statically allocated.
usb: add a HCD_DMA flag instead of guestimating DMA capabilities
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Dan Carpenter [Sat, 17 Aug 2019 06:55:20 +0000 (09:55 +0300)]
usb: host: ohci-pxa27x: Fix and & vs | typo
The code is supposed to clear the RH_A_NPS and RH_A_PSM bits, but it's
a no-op because of the & vs | typo. This bug predates git and it was
only discovered using static analysis so it must not affect too many
people in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190817065520.GA29951@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacob Huisman [Thu, 15 Aug 2019 17:42:10 +0000 (18:42 +0100)]
usb: usb-skeleton: make comment block in line with coding style
Comment block was not in accordance with coding style.
Fixes two checkpatch warnings:
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Linus Torvalds [Sun, 18 Aug 2019 16:51:48 +0000 (09:51 -0700)]
Merge tag 'for-5.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two fixes that popped up during testing:
- fix for sysfs-related code that adds/removes block groups, warnings
appear during several fstests in connection with sysfs updates in
5.3, the fix essentially replaces a workaround with scope NOFS and
applies to 5.2-based branch too
- add sanity check of trim range"
* tag 'for-5.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: trim: Check the range passed into to prevent overflow
Btrfs: fix sysfs warning and missing raid sysfs directories
Linus Torvalds [Sun, 18 Aug 2019 16:45:42 +0000 (09:45 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the inconsistent error handling in the umwait init code
- Rework the boot param zeroing so gcc9 stops complaining about out
of bound memset. The resulting source code is actually more sane to
read than the smart solution we had
- Maintainers update so Tony gets involved when Intel models are
added
- Some more fallthrough fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Save fields explicitly, zero out everything else
MAINTAINERS, x86/CPU: Tony Luck will maintain asm/intel-family.h
x86/fpu/math-emu: Address fallthrough warnings
x86/apic/32: Fix yet another implicit fallthrough warning
x86/umwait: Fix error handling in umwait_init()
Linus Torvalds [Sun, 18 Aug 2019 16:36:51 +0000 (09:36 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI mixed mode regression caused by recent rework
which did not take the firmware bitwidth into account"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-stub: Fix get_efi_config_table on mixed-mode setups
Linus Torvalds [Sun, 18 Aug 2019 16:26:16 +0000 (09:26 -0700)]
Merge tag 'spdx-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX fixes from Greg KH:
"Here are four small SPDX fixes for 5.3-rc5.
A few style fixes for some SPDX comments, added an SPDX tag for one
file, and fix up some GPL boilerplate for another file.
All of these have been in linux-next for a few weeks with no reported
issues (they are comment changes only, so that's to be expected...)"
* tag 'spdx-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
i2c: stm32: Use the correct style for SPDX License Identifier
intel_th: Use the correct style for SPDX License Identifier
coccinelle: api/atomic_as_refcounter: add SPDX License Identifier
kernel/configs: Replace GPL boilerplate code with SPDX identifier
Linus Torvalds [Sun, 18 Aug 2019 16:17:41 +0000 (09:17 -0700)]
Merge tag 'char-misc-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.3-rc5.
These are two different subsystems needing some fixes, the habanalabs
driver which is has some more big endian fixes for problems found. The
other are some small soundwire fixes, including some Kconfig
dependencies needed to resolve reported build errors.
All of these have been in linux-next this week with no reported
issues"
* tag 'char-misc-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: xilinx-sdfec: fix dependency and build error
habanalabs: fix device IRQ unmasking for BE host
habanalabs: fix endianness handling for internal QMAN submission
habanalabs: fix completion queue handling when host is BE
habanalabs: fix endianness handling for packets from user
habanalabs: fix DRAM usage accounting on context tear down
habanalabs: Avoid double free in error flow
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
Linus Torvalds [Sun, 18 Aug 2019 16:14:56 +0000 (09:14 -0700)]
Merge tag 'staging-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are four small staging and iio driver fixes for 5.3-rc5
Two are for the dt3000 comedi driver for some reported problems found
in that codebase, and two are some small iio fixes.
All of these have been in linux-next this week with no reported
issues"
* tag 'staging-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: dt3000: Fix rounding up of timer divisor
staging: comedi: dt3000: Fix signed integer overflow 'divider * base'
iio: adc: max9611: Fix temperature reading in probe
iio: frequency: adf4371: Fix output frequency setting
Linus Torvalds [Sun, 18 Aug 2019 16:11:29 +0000 (09:11 -0700)]
Merge tag 'usb-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are number of small USB fixes for 5.3-rc5.
Syzbot has been on a tear recently now that it has some good USB
debugging hooks integrated, so there's a number of fixes in here found
by those tools for some _very_ old bugs. Also a handful of gadget
driver fixes for reported issues, some hopefully-final dma fixes for
host controller drivers, and some new USB serial gadget driver ids.
All of these have been in linux-next this week with no reported issues
(the usb-serial ones were in linux-next in its own branch, but merged
into mine on Friday)"
* tag 'usb-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: add a hcd_uses_dma helper
usb: don't create dma pools for HCDs with a localmem_pool
usb: chipidea: imx: fix EPROBE_DEFER support during driver probe
usb: host: fotg2: restart hcd after port reset
USB: CDC: fix sanity checks in CDC union parser
usb: cdc-acm: make sure a refcount is taken early enough
USB: serial: option: add the BroadMobi BM818 card
USB: serial: option: Add Motorola modem UARTs
USB: core: Fix races in character device registration and deregistraion
usb: gadget: mass_storage: Fix races between fsg_disable and fsg_set_alt
usb: gadget: composite: Clear "suspended" on reset/disconnect
usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"
USB: serial: option: add D-Link DWM-222 device ID
USB: serial: option: Add support for ZTE MF871A
tcpm_register_port() will call some of the fusb302 code's callbacks
wich in turn will call fusb302_log(). So we need to call
fusb302_debugfs_init() before we call tcpm_register_port().
This fixes the following warning, which was caused by the logbuffer_lock
not yet being initialized (which is done by fusb302_debugfs_init):
Hans de Goede [Sat, 17 Aug 2019 18:43:38 +0000 (20:43 +0200)]
usb: typec: tcpm: Use usb_debug_root as root for our debugfs entry
Use usb_debug_root as root for our debugfs entry instead of creating our
own subdirectory under the debugfs root.
Another patch in this series will make the same change to the fusb302
driver, which also uses dev_name() (on the same device) for the debugfs
entry name. So we also prefix dev_name() with "tcpm-" here to avoid a
name conflict.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20190817184340.64086-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 18 Aug 2019 02:39:54 +0000 (19:39 -0700)]
Merge tag 'for-linus-2019-08-17' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:
- Revert of the REQ_NOWAIT_INLINE and associated dio changes. There
were still corner cases there, and even though I had a solution for
it, it's too involved for this stage. (me)
- Set of NVMe fixes (via Sagi)
- io_uring fix for fixed buffers (Anthony)
- io_uring defer issue fix (Jackie)
- Regression fix for queue sync at exit time (zhengbin)
- xen blk-back memory leak fix (Wenwen)"
* tag 'for-linus-2019-08-17' of git://git.kernel.dk/linux-block:
io_uring: fix an issue when IOSQE_IO_LINK is inserted into defer list
block: remove REQ_NOWAIT_INLINE
io_uring: fix manual setup of iov_iter for fixed buffers
xen/blkback: fix memory leaks
blk-mq: move cancel of requeue_work to the front of blk_exit_queue
nvme-pci: Fix async probe remove race
nvme: fix controller removal race with scan work
nvme-rdma: fix possible use-after-free in connect error flow
nvme: fix a possible deadlock when passthru commands sent to a multipath device
nvme-core: Fix extra device_put() call on error path
nvmet-file: fix nvmet_file_flush() always returning an error
nvmet-loop: Flush nvme_delete_wq when removing the port
nvmet: Fix use-after-free bug when a port is removed
nvme-multipath: revalidate nvme_ns_head gendisk in nvme_validate_ns
Linus Torvalds [Sun, 18 Aug 2019 02:31:30 +0000 (19:31 -0700)]
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fixes from Sasha Levin:
- A few fixes for the userspace hyper-v tools from Adrian Vladu.
- A fix for the hyper-v MAINTAINERs entry from Lan Tianyu.
- Fix for SPDX license identifier in the userspace tools from Nishad
Kamdar.
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
MAINTAINERS: Fix Hyperv vIOMMU driver file name
tools: hv: Use the correct style for SPDX License Identifier
tools: hv: fix typos in toolchain
tools: hv: fix KVP and VSS daemons exit code
tools: hv: fixed Python pep8/flake8 warnings for lsvmbus
tools: hv: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style
in the trace header file related to Microsoft Hyper-V
client drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Adrian Vladu [Mon, 6 May 2019 17:27:37 +0000 (17:27 +0000)]
tools: hv: fixed Python pep8/flake8 warnings for lsvmbus
Fixed pep8/flake8 python style code for lsvmbus tool.
The TAB indentation was on purpose ignored (pep8 rule W191) to make
sure the code is complying with the Linux code guideline.
The following command doe not show any warnings now:
pep8 --ignore=W191 lsvmbus
flake8 --ignore=W191 lsvmbus
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sasha Levin <sashal@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linus Torvalds [Sat, 17 Aug 2019 17:44:50 +0000 (10:44 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has one revert because of a regression, two fixes for tiny race
windows (which we were not able to trigger), a MAINTAINERS addition,
and a SPDX fix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32: Use the correct style for SPDX License Identifier
i2c: emev2: avoid race when unregistering slave client
i2c: rcar: avoid race when unregistering slave client
MAINTAINERS: i2c-imx: take over maintainership
Revert "i2c: imx: improve the error handling in i2c_imx_dma_request()"
Linus Torvalds [Sat, 17 Aug 2019 17:36:47 +0000 (10:36 -0700)]
Merge tag 'riscv/for-v5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- Two patches to fix significant bugs in floating point register
context handling
- A minor fix in RISC-V flush_tlb_page(), to supply a valid end address
to flush_tlb_range()
- Two minor defconfig additions: to build the virtio hwrng driver by
default (for QEMU targets), and to partially synchronize the 32-bit
defconfig with the 64-bit defconfig
* tag 'riscv/for-v5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Make __fstate_clean() work correctly.
riscv: Correct the initialized flow of FP register
riscv: defconfig: Update the defconfig
riscv: rv32_defconfig: Update the defconfig
riscv: fix flush_tlb_range() end address for flush_tlb_page()
Linus Torvalds [Fri, 16 Aug 2019 17:51:47 +0000 (10:51 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Don't taint the kernel if CPUs have different sets of page sizes
supported (other than the one in use).
- Issue I-cache maintenance for module ftrace trampoline.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side
arm64: cpufeature: Don't treat granule sizes as strict
Will Deacon [Fri, 16 Aug 2019 13:57:43 +0000 (14:57 +0100)]
arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc83 ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: James Morse <james.morse@arm.com> Cc: <stable@vger.kernel.org> Fixes: be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code") Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Aug 2019 16:13:16 +0000 (09:13 -0700)]
Merge tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These add a check to avoid recent suspend-to-idle power regression on
systems with NVMe drives where the PCIe ASPM policy is "performance"
(or when the kernel is built without ASPM support), fix an issue
related to frequency limits in the schedutil cpufreq governor and fix
a mistake related to the PM QoS usage in the cpufreq core introduced
recently.
Specifics:
- Disable NVMe power optimization related to suspend-to-idle added
recently on systems where PCIe ASPM is not able to put PCIe links
into low-power states to prevent excess power from being drawn by
the system while suspended (Rafael Wysocki).
- Make the schedutil governor handle frequency limits changes
properly in all cases (Viresh Kumar).
- Prevent the cpufreq core from treating positive values returned by
dev_pm_qos_update_request() as errors (Viresh Kumar)"
* tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled
PCI/ASPM: Add pcie_aspm_enabled()
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
Linus Torvalds [Fri, 16 Aug 2019 15:49:45 +0000 (08:49 -0700)]
Merge tag 'sound-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small fixes targeted for stable:
- Two fixes for USB-audio with malformed descriptor, spotted by
fuzzers
- Two fixes Conexant HD-audio codec wrt power management
- Quirks for HD-audio AMD platform and HP laptop
- HD-audio memory leak fix"
* tag 'sound-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix a stack buffer overflow bug in check_input_term
ALSA: usb-audio: Fix an OOB bug in parse_audio_mixer_unit
ALSA: hda - Add a generic reboot_notify
ALSA: hda - Let all conexant codec enter D3 when rebooting
ALSA: hda/realtek - Add quirk for HP Envy x360
ALSA: hda - Fix a memory leak bug
ALSA: hda - Apply workaround for another AMD chip 1022:1487
Linus Torvalds [Fri, 16 Aug 2019 15:41:15 +0000 (08:41 -0700)]
Merge tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too crazy this week, one amdgpu fix to use vmalloc for a
struct that grew in size, and another MST fix for nouveau, and some
other misc fixes:
* tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes
drm/ast: Fixed reboot test may cause system hanged
drm/scheduler: use job count instead of peek
drm/amd/display: use kvmalloc for dc_state (v2)
drm/amdgpu: fix gfx9 soft recovery
drm/i915: Use after free in error path in intel_vgpu_create_workload()
John Hubbard [Wed, 31 Jul 2019 05:46:27 +0000 (22:46 -0700)]
x86/boot: Save fields explicitly, zero out everything else
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds
memset, if the memset goes accross several fields of a struct. This
generated a couple of warnings on x86_64 builds in sanitize_boot_params().
Fix this by explicitly saving the fields in struct boot_params
that are intended to be preserved, and zeroing all the rest.
[ tglx: Tagged for stable as it breaks the warning free build there as well ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com
Merge tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for v5.3-rc5
Pierre sent fixes which are queued now for v5.3-rc5 are:
- regmap dependecy
- cadence register definitions
* tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
USB: phy: fsl-usb: convert platform driver to use dev_groups
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Hui Peng [Thu, 15 Aug 2019 04:31:34 +0000 (00:31 -0400)]
ALSA: usb-audio: Fix a stack buffer overflow bug in check_input_term
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
Colin Ian King [Fri, 9 Aug 2019 17:33:14 +0000 (18:33 +0100)]
USB: storage: isd200: remove redundant assignment to variable sendToTransport
The variable sendToTransport is being initialized with a value that is
never read and is being re-assigned a little later on. The assignment
is redundant and hence can be removed.
Heikki Krogerus [Wed, 14 Aug 2019 13:24:19 +0000 (16:24 +0300)]
usb: typec: fusb302: Always provide fwnode for the port
By registering a software fwnode for the port when the
firmware does not supply one, we can always provide tcpm the
connector capabilities by using the common USB connector
device properties instead of using tcpc_config platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190814132419.39759-4-heikki.krogerus@linux.intel.com Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190814132419.39759-3-heikki.krogerus@linux.intel.com Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 14 Aug 2019 13:24:17 +0000 (16:24 +0300)]
usb: typec: fusb302: Remove unused properties
Removing the deprecated fusb302 specific properties. There
are no more platforms using them.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190814132419.39759-2-heikki.krogerus@linux.intel.com Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 15 Aug 2019 19:29:36 +0000 (12:29 -0700)]
Merge tag 'xfs-5.3-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix crashes when the attr fork isn't present due to errors but inode
inactivation tries to zap the attr data anyway.
- Convert more directory corruption debugging asserts to actual
EFSCORRUPTED returns instead of blowing up later on.
- Don't fail writeback just because we ran out of memory allocating
metadata log data.
* tag 'xfs-5.3-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't crash on null attr fork xfs_bmapi_read
xfs: remove more ondisk directory corruption asserts
fs: xfs: xfs_log: Don't use KM_MAYFAIL at xfs_log_reserve().
Jackie Liu [Wed, 14 Aug 2019 09:35:22 +0000 (17:35 +0800)]
io_uring: fix an issue when IOSQE_IO_LINK is inserted into defer list
This patch may fix two issues:
First, when IOSQE_IO_DRAIN set, the next IOs need to be inserted into
defer list to delay execution, but link io will be actively scheduled to
run by calling io_queue_sqe.
Second, when multiple LINK_IOs are inserted together with defer_list,
the LINK_IO is no longer keep order.
|-------------|
| LINK_IO | ----> insert to defer_list -----------
|-------------| |
| LINK_IO | ----> insert to defer_list ----------|
|-------------| |
| LINK_IO | ----> insert to defer_list ----------|
|-------------| |
| NORMAL_IO | ----> insert to defer_list ----------|
|-------------| |
|
queue_work at same time <-----|
Fixes: 9e645e1105c ("io_uring: add support for sqe links") Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 15 Aug 2019 17:09:16 +0000 (11:09 -0600)]
block: remove REQ_NOWAIT_INLINE
We had a few issues with this code, and there's still a problem around
how we deal with error handling for chained/split bios. For now, just
revert the code and we'll try again with a thoroug solution. This
reverts commits:
e15c2ffa1091 ("block: fix O_DIRECT error handling for bio fragments") 0eb6ddfb865c ("block: Fix __blkdev_direct_IO() for bio fragments") 6a43074e2f46 ("block: properly handle IOCB_NOWAIT for async O_DIRECT IO") 893a1c97205a ("blk-mq: allow REQ_NOWAIT to return an error inline")
io_uring: fix manual setup of iov_iter for fixed buffers
Commit bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed
buffers") introduced an optimization to avoid using the slow
iov_iter_advance by manually populating the iov_iter iterator in some
cases.
However, the computation of the iterator count field was erroneous: The
first bvec was always accounted for an extent of page size even if the
bvec length was smaller.
In consequence, some I/O operations on fixed buffers were unable to
operate on the full extent of the buffer, consistently skipping some
bytes at the end of it.
Fixes: bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed buffers") Cc: stable@vger.kernel.org Signed-off-by: Aleix Roca Nonell <aleix.rocanonell@bsc.es> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Thu, 15 Aug 2019 16:20:17 +0000 (09:20 -0700)]
Merge tag 'auxdisplay-for-linus-v5.3-rc5' of git://github.com/ojeda/linux
Pull auxdisplay fixes from Miguel Ojeda:
"A few minor auxdisplay improvements:
- A couple of small header cleanups for charlcd (Masahiro Yamada)
- A trivial typo fix for the examples of cfag12864b (Masahiro Yamada)
- An Kconfig help text improvement for charlcd (Mans Rullgard)
- An error path fix for panel (zhengbin)"
* tag 'auxdisplay-for-linus-v5.3-rc5' of git://github.com/ojeda/linux:
auxdisplay: Fix a typo in cfag12864b-example.c
auxdisplay: charlcd: add include guard to charlcd.h
auxdisplay: charlcd: move charlcd.h to drivers/auxdisplay
auxdisplay: charlcd: add help text for backlight initial state
auxdisplay: panel: need to delete scan_timer when misc_register fails in panel_attach
Linus Torvalds [Thu, 15 Aug 2019 16:18:56 +0000 (09:18 -0700)]
Merge tag 'devicetree-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix building DT binding examples for in tree builds
- Correct some refcounting in adjust_local_phandle_references()
- Update FSL FEC binding with deprecated properties
- Schema fix in stm32 pinctrl
- Fix typo in of_irq_parse_one docbook comment
* tag 'devicetree-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: irq: fix a trivial typo in a doc comment
dt-bindings: pinctrl: stm32: Fix 'st,syscfg' schema
dt-bindings: fec: explicitly mark deprecated properties
of: resolver: Add of_node_put() before return and break
dt-bindings: Fix generated example files getting added to schemas
Randy Dunlap [Tue, 13 Aug 2019 23:01:20 +0000 (16:01 -0700)]
misc: xilinx-sdfec: fix dependency and build error
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so XILINX_SDFEC should depend
on HAS_IOMEM. Fixes this build error (as seen on UML builds):
The USB buffer allocation code is the only place in the usb core (and in
fact the whole kernel) that uses is_device_dma_capable, while the URB
mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer
allocation to use the uses_dma flag used by the rest of the USB code,
and create a helper in hcd.h that checks this flag as well as the
CONFIG_HAS_DMA to simplify the caller a bit.
usb: don't create dma pools for HCDs with a localmem_pool
If the HCD provides a localmem pool we will never use the DMA pools, so
don't create them.
Fixes: b0310c2f09bb ("USB: use genalloc for USB HCs with local memory") Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190811080520.21712-2-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
André Draszik [Sat, 10 Aug 2019 15:07:58 +0000 (16:07 +0100)]
usb: chipidea: imx: fix EPROBE_DEFER support during driver probe
If driver probe needs to be deferred, e.g. because ci_hdrc_add_device()
isn't ready yet, this driver currently misbehaves badly:
a) success is still reported to the driver core (meaning a 2nd
probe attempt will never be done), leaving the driver in
a dysfunctional state and the hardware unusable
c) the error path in combination with driver removal causes
imbalanced calls to the clk_*() and pm_()* APIs
a) happens because the original intended return value is
overwritten (with 0) by the return code of
regulator_disable() in ci_hdrc_imx_probe()'s error path
b) happens because ci_pdev is -EPROBE_DEFER, which causes
ci_hdrc_remove_device() to OOPS
Fix a) by being more careful in ci_hdrc_imx_probe()'s error
path and not overwriting the real error code
Fix b) by calling the respective cleanup functions during
remove only when needed (when ci_pdev != NULL, i.e. when
everything was initialised correctly). This also has the
side effect of not causing imbalanced clk_*() and pm_*()
API calls as part of the error code path.
Tony Lindgren [Thu, 15 Aug 2019 08:26:02 +0000 (01:26 -0700)]
USB: serial: option: Add Motorola modem UARTs
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
Tony Luck [Wed, 14 Aug 2019 23:40:30 +0000 (16:40 -0700)]
MAINTAINERS, x86/CPU: Tony Luck will maintain asm/intel-family.h
There are a few different subsystems in the kernel that depend on model
specific behaviour (perf, EDAC, power, ...). Easier for just one person
to have the task to get new model numbers included instead of having
these groups trip over each other to do it.
[ bp: s/Cpu/CPU/ and add x86@kernel.org so that it gets CCed too as
FYI. ]
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190814234030.30817-1-tony.luck@intel.com
Lyude Paul [Fri, 9 Aug 2019 00:53:05 +0000 (20:53 -0400)]
drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes
I -thought- I had fixed this entirely, but it looks like that I didn't
test this thoroughly enough as we apparently still make one big mistake
with nv50_msto_atomic_check() - we don't handle the following scenario:
* CRTC #1 has n VCPI allocated to it, is attached to connector DP-4
which is attached to encoder #1. enabled=y active=n
* CRTC #1 is changed from DP-4 to DP-5, causing:
* DP-4 crtc=#1→NULL (VCPI n→0)
* DP-5 crtc=NULL→#1
* CRTC #1 steals encoder #1 back from DP-4 and gives it to DP-5
* CRTC #1 maintains the same mode as before, just with a different
connector
* mode_changed=n connectors_changed=y
(we _SHOULD_ do VCPI 0→n here, but don't)
Once the above scenario is repeated once, we'll attempt freeing VCPI
from the connector that we didn't allocate due to the connectors
changing, but the mode staying the same. Sigh.
Since nv50_msto_atomic_check() has broken a few times now, let's rethink
things a bit to be more careful: limit both VCPI/PBN allocations to
mode_changed || connectors_changed, since neither VCPI or PBN should
ever need to change outside of routing and mode changes.
Changes since v1:
* Fix accidental reversal of clock and bpp arguments in
drm_dp_calc_pbn_mode() - William Lewis
Signed-off-by: Lyude Paul <lyude@redhat.com> Reported-by: Bohdan Milar <bmilar@redhat.com> Tested-by: Bohdan Milar <bmilar@redhat.com> Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST")
References: 412e85b60531 ("drm/nouveau: Only release VCPI slots on mode changes") Cc: Lyude Paul <lyude@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@redhat.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Juston Li <juston.li@intel.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Karol Herbst <karolherbst@gmail.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Cc: <stable@vger.kernel.org> # v5.1+ Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190809005307.18391-1-lyude@redhat.com
The proper way to add additional contraints to an existing json-schema
is using 'allOf' to reference the base schema. Using just '$ref' doesn't
work. Fix this for the 'st,syscfg' property.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-gpio@vger.kernel.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
Linus Torvalds [Wed, 14 Aug 2019 21:21:14 +0000 (14:21 -0700)]
Merge tag 'afs-fixes-20190814' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull afs fixes from David Howells:
- Fix the CB.ProbeUuid handler to generate its reply correctly.
- Fix a mix up in indices when parsing a Volume Location entry record.
- Fix a potential NULL-pointer deref when cleaning up a read request.
- Fix the expected data version of the destination directory in
afs_rename().
- Fix afs_d_revalidate() to only update d_fsdata if it's not the same
as the directory data version to reduce the likelihood of overwriting
the result of a competing operation. (d_fsdata carries the directory
DV or the least-significant word thereof).
- Fix the tracking of the data-version on a directory and make sure
that dentry objects get properly initialised, updated and
revalidated.
Also fix rename to update d_fsdata to match the new directory's DV if
the dentry gets moved over and unhash the dentry to stop
afs_d_revalidate() from interfering.
* tag 'afs-fixes-20190814' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix missing dentry data version updating
afs: Only update d_fsdata if different in afs_d_revalidate()
afs: Fix off-by-one in afs_rename() expected data version calculation
fs: afs: Fix a possible null-pointer dereference in afs_put_read()
afs: Fix loop index mixup in afs_deliver_vl_get_entry_by_name_u()
afs: Fix the CB.ProbeUuid service handler to reply correctly
Christian König [Fri, 9 Aug 2019 15:27:21 +0000 (17:27 +0200)]
drm/scheduler: use job count instead of peek
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Monk.liu@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vincent Chen [Wed, 14 Aug 2019 08:23:52 +0000 (16:23 +0800)]
riscv: Correct the initialized flow of FP register
The following two reasons cause FP registers are sometimes not
initialized before starting the user program.
1. Currently, the FP context is initialized in flush_thread() function
and we expect these initial values to be restored to FP register when
doing FP context switch. However, the FP context switch only occurs in
switch_to function. Hence, if this process does not be scheduled out
and scheduled in before entering the user space, the FP registers
have no chance to initialize.
2. In flush_thread(), the state of reg->sstatus.FS inherits from the
parent. Hence, the state of reg->sstatus.FS may be dirty. If this
process is scheduled out during flush_thread() and initializing the
FP register, the fstate_save() in switch_to will corrupt the FP context
which has been initialized until flush_thread().
To solve the 1st case, the initialization of the FP register will be
completed in start_thread(). It makes sure all FP registers are initialized
before starting the user program. For the 2nd case, the state of
reg->sstatus.FS in start_thread will be set to SR_FS_OFF to prevent this
process from corrupting FP context in doing context save. The FP state is
set to SR_FS_INITIAL in start_trhead().
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 7db91e57a0acd ("RISC-V: Task implementation") Cc: stable@vger.kernel.org
[paul.walmsley@sifive.com: fixed brace alignment issue reported by
checkpatch] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Linus Torvalds [Wed, 14 Aug 2019 18:10:38 +0000 (11:10 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"Fairly small pull request for -rc3. I'm out of town the rest of this
week, so I made sure to clean out as much as possible from patchworks
in enough time for 0-day to chew through it (Yay! for 0-day being back
online! :-)). Jason might send through any emergency stuff that could
pop up, otherwise I'm back next week.
The only real thing of note is the siw ABI change. Since we just
merged siw *this* release, there are no prior kernel releases to
maintain kernel ABI with. I told Bernard that if there is anything
else about the siw ABI he thinks he might want to change before it
goes set in stone, he should get it in ASAP. The siw module was around
for several years outside the kernel tree, and it had to be revamped
considerably for inclusion upstream, so we are making no attempts to
be backward compatible with the out of tree version. Once 5.3 is
actually released, we will have our baseline ABI to maintain.
Summary:
- Fix a memory registration release flow issue that was causing a
WARN_ON (mlx5)
- If the counters for a port aren't allocated, then we can't do
operations on the non-existent counters (core)
- Check the right variable for error code result (mlx5)
- Fix a use after free issue (mlx5)
- Fix an off by one memory leak (siw)
- Actually return an error code on error (core)
- Allow siw to be built on 32bit arches (siw, ABI change, but OK
since siw was just merged this merge window and there is no prior
released kernel to maintain compatibility with and we also updated
the rdma-core user space package to match)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/siw: Change CQ flags from 64->32 bits
RDMA/core: Fix error code in stat_get_doit_qp()
RDMA/siw: Fix a memory leak in siw_init_cpulist()
IB/mlx5: Fix use-after-free error while accessing ev_file pointer
IB/mlx5: Check the correct variable in error handling code
RDMA/counter: Prevent QP counter binding if counters unsupported
IB/mlx5: Fix implicit MR release flow
Hui Peng [Wed, 14 Aug 2019 02:34:04 +0000 (22:34 -0400)]
ALSA: usb-audio: Fix an OOB bug in parse_audio_mixer_unit
The `uac_mixer_unit_descriptor` shown as below is read from the
device side. In `parse_audio_mixer_unit`, `baSourceID` field is
accessed from index 0 to `bNrInPins` - 1, the current implementation
assumes that descriptor is always valid (the length of descriptor
is no shorter than 5 + `bNrInPins`). If a descriptor read from
the device side is invalid, it may trigger out-of-bound memory
access.
projects / mirror_ubuntu-hirsute-kernel.git / log