There are reports wrt lockdep splat in nftables, e.g.:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 31416 at net/netfilter/nf_tables_api.c:622
lockdep_nfnl_nft_mutex_not_held+0x28/0x38 [nf_tables]
...
These are caused by an earlier, unrelated bug such as a n ABBA deadlock
in a different subsystem.
In such an event, lockdep is disabled and lockdep_is_held returns true
unconditionally. This then causes the WARN() in nf_tables.
Make the WARN conditional on lockdep still active to avoid this.
Fixes: f102d66b335a417 ("netfilter: nf_tables: use dedicated mutex to guard transactions") Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Link: https://lore.kernel.org/linux-kselftest/CA+G9fYvFUpODs+NkSYcnwKnXm62tmP=ksLeBPmB+KFrB2rvCtQ@mail.gmail.com/ Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Building on arch/s390/ results in this build error:
cc1: some warnings being treated as errors
../drivers/md/dm-writecache.c: In function 'persistent_memory_claim':
../drivers/md/dm-writecache.c:323:1: error: no return statement in function returning non-void [-Werror=return-type]
Fix this by replacing the BUG() with an -EOPNOTSUPP return.
Fixes: 48debafe4f2f ("dm: add writecache target") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This code does not ensure that the whole buffer is initialized and none
of the callers check for errors so potentially none of the buffer is
initialized. Add a memset to eliminate this bug.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix to return a negative error code from the error handling case
instead of 0 in function wm_adsp_load(), as done elsewhere in this
function.
Fixes: 170b1e123f38 ("ASoC: wm_adsp: Add support for new Halo core DSPs") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Luo Meng <luomeng12@huawei.com> Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20201123133839.4073787-1-luomeng12@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
In the commit fdeba99b1e58
("tipc: fix use-after-free in tipc_bcast_get_mode"), we're trying
to make sure the tipc_net_finalize_work work item finished if it
enqueued. But calling flush_scheduled_work() is not just affecting
above work item but either any scheduled work. This has turned out
to be overkill and caused to deadlock as syzbot reported:
======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2-next-20200828-syzkaller #0 Not tainted
------------------------------------------------------
kworker/u4:6/349 is trying to acquire lock: ffff8880aa063d38 ((wq_completion)events){+.+.}-{0:0}, at: flush_workqueue+0xe1/0x13e0 kernel/workqueue.c:2777
but task is already holding lock: ffffffff8a879430 (pernet_ops_rwsem){++++}-{3:3}, at: cleanup_net+0x9b/0xb10 net/core/net_namespace.c:565
v1:
To fix the original issue, we replace above calling by introducing
a bit flag. When a namespace cleaned-up, bit flag is set to zero and:
- tipc_net_finalize functionial just does return immediately.
- tipc_net_finalize_work does not enqueue into the scheduled work queue.
v2:
Use cancel_work_sync() helper to make sure ONLY the
tipc_net_finalize_work() stopped before releasing bcbase object.
Reported-by: syzbot+d5aa7e0385f6a5d0f4fd@syzkaller.appspotmail.com Fixes: fdeba99b1e58 ("tipc: fix use-after-free in tipc_bcast_get_mode") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
To detect potential bugs in CAN protocol implementations (double removal of
receiver entries) a WARN() statement has been used if no matching list item was
found for removal.
The fault injection issued by syzkaller was able to create a situation where
the closing of a socket runs simultaneously to the notifier call chain for
removing the CAN network device in use.
This case is very unlikely in real life but it doesn't break anything.
Therefore we just replace the WARN() statement with pr_warn() to preserve the
notification for the CAN protocol development.
Reported-by: syzbot+381d06e0c8eaacb8706f@syzkaller.appspotmail.com Reported-by: syzbot+d0ddd88c9a7432f041e6@syzkaller.appspotmail.com Reported-by: syzbot+76d62d3b8162883c7d11@syzkaller.appspotmail.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201126192140.14350-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Lilith >_> and Claudio Bozzato of Cisco Talos security team reported
that collect_syscall() improperly casts the syscall registers to 64-bit
values leaking the uninitialized last 24 bytes on 32-bit platforms, that
are visible in /proc/self/syscall.
The cause is that info->data.args are u64 while syscall_get_arguments()
uses longs, as hinted by the bogus pointer cast in the function.
Let's just proceed like the other call places, by retrieving the
registers into an array of longs before assigning them to the caller's
array. This was successfully tested on x86_64, i386 and ppc32.
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org Fixes: 16270145ce6b ("tracing: Add trace options for core options to instances") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to the AMD IOMMU spec, the commit 73db2fc595f3
("iommu/amd: Increase interrupt remapping table limit to 512 entries")
also requires the interrupt table length (IntTabLen) to be set to 9
(power of 2) in the device table mapping entry (DTE).
Fixes: 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries") Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20201207091920.3052-1-suravee.suthikulpanit@amd.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de> Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Speakup exposing a line discipline allows userland to try to use it,
while it is deemed to be useless, and thus uselessly exposes potential
bugs. One of them is simply that in such a case if the line sends data,
spk_ttyio_receive_buf2 is called and crashes since spk_ttyio_synth
is NULL.
This change restricts the use of the speakup line discipline to
speakup drivers, thus avoiding such kind of issues altogether.
When investigating a slab cache bloat problem, significant amount of
negative dentry cache was seen, but confusingly they neither got shrunk
by reclaimer (the host has very tight memory) nor be shrunk by dropping
cache. The vmcore shows there are over 14M negative dentry objects on
lru, but tracing result shows they were even not scanned at all.
Further investigation shows the memcg's vfs shrinker_map bit is not set.
So the reclaimer or dropping cache just skip calling vfs shrinker. So
we have to reboot the hosts to get the memory back.
I didn't manage to come up with a reproducer in test environment, and
the problem can't be reproduced after rebooting. But it seems there is
race between shrinker map bit clear and reparenting by code inspection.
The hypothesis is elaborated as below.
The memcg hierarchy on our production environment looks like:
root
/ \
system user
The main workloads are running under user slice's children, and it
creates and removes memcg frequently. So reparenting happens very often
under user slice, but no task is under user slice directly.
So with the frequent reparenting and tight memory pressure, the below
hypothetical race condition may happen:
CPU A CPU B
reparent
dst->nr_items == 0
shrinker:
total_objects == 0
add src->nr_items to dst
set_bit
return SHRINK_EMPTY
clear_bit
child memcg offline
replace child's kmemcg_id with
parent's (in memcg_offline_kmem())
list_lru_del() between shrinker runs
see parent's kmemcg_id
dec dst->nr_items
reparent again
dst->nr_items may go negative
due to concurrent list_lru_del()
The second run of shrinker:
read nr_items without any
synchronization, so it may
see intermediate negative
nr_items then total_objects
may return 0 coincidently
keep the bit cleared
dst->nr_items != 0
skip set_bit
add scr->nr_item to dst
After this point dst->nr_item may never go zero, so reparenting will not
set shrinker_map bit anymore. And since there is no task under user
slice directly, so no new object will be added to its lru to set the
shrinker map bit either. That bit is kept cleared forever.
How does list_lru_del() race with reparenting? It is because reparenting
replaces children's kmemcg_id to parent's without protecting from
nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually
deleting items from child's lru, but dec'ing parent's nr_items, so the
parent's nr_items may go negative as commit 2788cf0c401c ("memcg:
reparent list_lrus and free kmemcg_id on css offline") says.
Since it is impossible that dst->nr_items goes negative and
src->nr_items goes zero at the same time, so it seems we could set the
shrinker map bit iff src->nr_items != 0. We could synchronize
list_lru_count_one() and reparenting with nlru->lock, but it seems
checking src->nr_items in reparenting is the simplest and avoids lock
contention.
Fixes: fae91d6d8be5 ("mm/list_lru.c: set bit in memcg shrinker bitmap on first list_lru item appearance") Suggested-by: Roman Gushchin <guro@fb.com> Signed-off-by: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Roman Gushchin <guro@fb.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <stable@vger.kernel.org> [4.19] Link: https://lkml.kernel.org/r/20201202171749.264354-1-shy828301@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
'format_corename()' will splite 'core_pattern' on spaces when it is in
pipe mode, and take helper_argv[0] as the path to usermode executable.
It works fine in most cases.
However, if there is a space between '|' and '/file/path', such as
'| /usr/lib/systemd/systemd-coredump %P %u %g', then helper_argv[0] will
be parsed as '', and users will get a 'Core dump to | disabled'.
It is not friendly to users, as the pattern above was valid previously.
Fix this by ignoring the spaces between '|' and '/file/path'.
Fixes: 315c69261dd3 ("coredump: split pipe command whitespace before expanding template") Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Paul Wise <pabs3@bonedaddy.net> Cc: Jakub Wilk <jwilk@jwilk.net> [https://bugs.debian.org/924398] Cc: Neil Horman <nhorman@tuxdriver.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/5fb62870.1c69fb81.8ef5d.af76@mx.google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fixes sparse warnings:
drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit
drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit
Fixes: 971888c46993f ("dm: hold DM table for duration of ioctl rather than use blkdev_get") Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
With virtio multiqueue, normally each queue IRQ is mapped to a CPU.
Commit 0d9f0a52c8b9f ("virtio_scsi: use virtio IRQ affinity") exposed
an existing shortcoming of the arch code by moving virtio_scsi to
the automatic IRQ affinity assignment.
The affinity is correctly computed in msi_desc but this is not applied
to the system IRQs.
It appears the affinity is correctly passed to rtas_setup_msi_irqs() but
lost at this point and never passed to irq_domain_alloc_descs()
(see commit 06ee6d571f0e ("genirq: Add affinity hint to irq allocation"))
because irq_create_mapping() doesn't take an affinity parameter.
Use the new irq_create_mapping_affinity() function, which allows to forward
the affinity setting from rtas_setup_msi_irqs() to irq_domain_alloc_descs().
With this change, the virtqueues are correctly dispatched between the CPUs
on pseries.
Fixes: e75eafb9b039 ("genirq/msi: Switch to new irq spreading infrastructure") Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Greg Kurz <groug@kaod.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201126082852.1178497-3-lvivier@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There is currently no way to convey the affinity of an interrupt
via irq_create_mapping(), which creates issues for devices that
expect that affinity to be managed by the kernel.
In order to sort this out, rename irq_create_mapping() to
irq_create_mapping_affinity() with an additional affinity parameter that
can be passed down to irq_domain_alloc_descs().
irq_create_mapping() is re-implemented as a wrapper around
irq_create_mapping_affinity().
No functional change.
Fixes: e75eafb9b039 ("genirq/msi: Switch to new irq spreading infrastructure") Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Greg Kurz <groug@kaod.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201126082852.1178497-2-lvivier@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit c1a6c5ac4278 ("scsi: mpt3sas: For NVME device, issue a protocol
level reset") modified the ioctl path 'timeout' variable type to u8 from
unsigned long, limiting the maximum timeout value that the driver can
support to 255 seconds.
If the management application is requesting a higher value the resulting
timeout will be zero. The operation times out immediately and the ioctl
request fails.
Change datatype back to unsigned long.
Link: https://lore.kernel.org/r/20201125094838.4340-1-suganath-prabu.subramani@broadcom.com Fixes: c1a6c5ac4278 ("scsi: mpt3sas: For NVME device, issue a protocol level reset") Cc: <stable@vger.kernel.org> #v4.18+ Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Ville noticed that the last mocs entry is used unconditionally by the HW
when it performs cache evictions, and noted that while the value is not
meant to be writable by the driver, we should program it to a reasonable
value nevertheless.
As it turns out, we can change the value of mocs:63 and the value we
were programming into it would cause hard hangs in conjunction with
atomic operations.
v2: Add details from bspec about how it is used by HW
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2707 Fixes: 3bbaba0ceaa2 ("drm/i915: Added Programming of the MOCS") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: <stable@vger.kernel.org> # v4.3+ Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201126140841.1982-1-chris@chris-wilson.co.uk
(cherry picked from commit 977933b5da7c16f39295c4c1d4259a58ece65dbe) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This happens because remove_unplugged_switch() calls tb_switch_remove()
that releases the memory pointed by sw so the following lines reference
to a memory that might be released already.
Fix this by saving pointer to the parent device before calling
tb_switch_remove().
Reported-by: Paulian Bogdan Marinca <paulian@marinca.net> Fixes: 4f7c2e0d8765 ("thunderbolt: Make sure device runtime resume completes before taking domain lock") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy(). Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
A customer has reported that several files in their multi-threaded app
were left with size of 0 because most of the read(2) calls returned
-EINTR and they assumed no bytes were read. Obviously, they could
have fixed it by simply retrying on -EINTR.
We noticed that most of the -EINTR on read(2) were due to real-time
signals sent by glibc to process wide credential changes (SIGRT_1),
and its signal handler had been established with SA_RESTART, in which
case those calls could have been automatically restarted by the
kernel.
Let the kernel decide to whether or not restart the syscalls when
there is a signal pending in __smb_send_rqst() by returning
-ERESTARTSYS. If it can't, it will return -EINTR anyway.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com Cc: stable@vger.kernel.org Fixes: a124692b698b0 ("ftrace: Enable trampoline when rec count returns back to one") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
HP Spectre x360 Convertible 15" version (SSID 103c:827f) needs the
same quirk to make the mute LED working like other models.
System Information
Manufacturer: HP
Product Name: HP Spectre x360 Convertible 15-bl1XX
ASUS Zephyrus G14 has two speaker pins, and the auto-parser tries to
assign an individual DAC to each pin as much as possible.
Unfortunately the third DAC has no volume control unlike the two DACs,
and this resulted in the inconsistent speaker volumes.
As a workaround, wire both speaker pins to the same DAC by modifying
the existing quirk (ALC289_FIXUP_ASUS_GA401) applied to this device.
Since this quirk entry is chained by another, we need to avoid
applying the DAC assignment change for it. Luckily, there is another
quirk entry (ALC289_FIXUP_ASUS_GA502) doing the very same thing, so we
can chain to the GA502 quirk instead.
Note that this patch uses a new flag of the generic parser,
obey_preferred_dacs, for enforcing the DACs.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
This is a partial revert of commit 2bb70f0a4b23 ("USB: serial:
option: support dynamic Quectel USB compositions")
The Quectel BG96 is different from most other modern Quectel modems,
having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff
class/subclass/protocol. Including it in the change to accommodate
dynamic function mapping was incorrect.
Revert to interface number matching for the BG96, assuming static
layout of the RMNET function on interface 4. This restores support
for the serial functions on interfaces 2 and 3.
Full lsusb output for the BG96:
Bus 002 Device 003: ID 2c7c:0296
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2c7c
idProduct 0x0296
bcdDevice 0.00
iManufacturer 3 Qualcomm, Incorporated
iProduct 2 Qualcomm CDMA Technologies MSM
iSerial 4 d1098243
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 145
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 1 Qualcomm Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 254
bInterfaceProtocol 255
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Cc: Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Fixes: 2bb70f0a4b23 ("USB: serial: option: support dynamic Quectel USB compositions") Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Update the USB serial option driver support for the Fibocom NL668 Cat.4
LTE modules as there are actually several different variants.
Got clarifications from Fibocom, there are distinct products:
- VID:PID 1508:1001, NL668 for IOT (no MBIM interface)
- VID:PID 2cb7:01a0, NL668-AM and NL652-EU are laptop M.2 cards (with
MBIM interfaces for Windows/Linux/Chrome OS), respectively for Americas
and Europe.
Add PID for CH340 that's found on a ch341 based Programmer made by keeyees.
The specific device that contains the serial converter is described
here: http://www.keeyees.com/a/Products/ej/36.html
The driver works flawlessly as soon as the new PID (0x5512) is added to
it.
The function may be unbound causing the ffs_ep and its descriptors
to be freed while userspace is in the middle of an ioctl requesting
the same descriptors. Avoid dangling pointer reference by first
making a local copy of desctiptors before releasing the spinlock.
Fixes: c559a3534109 ("usb: gadget: f_fs: add ioctl returning ep descriptor") Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201130203453.28154-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Stefan Bader [Thu, 17 Dec 2020 13:57:00 +0000 (14:57 +0100)]
UBUNTU: [dep-8] Allow all hwe kernels
BugLink: https://bugs.launchpad.net/bugs/1908529
The dep-8 tests are limited to kernels which are bootable. But with
moving to versioned hwe kernels this would require constant change.
To avoid that, just allow any kernel source starting with linux-hwe.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This commit is not suitable for 5.4-stable because the openat2 system
call does not exist in v5.4.
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Reference: https://lore.kernel.org/stable/20201216181353.30321-1-kamal@canonical.com/ Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1908342
The cleanup function in this script that tries to delete hv-1 / hv-2
vm-1 / vm-2 netns will generate some uncessary error messages:
Cannot remove namespace file "/run/netns/hv-2": No such file or directory
Cannot remove namespace file "/run/netns/vm-1": No such file or directory
Cannot remove namespace file "/run/netns/vm-2": No such file or directory
Redirect it to /dev/null like other commands in the cleanup function
to reduce confusion.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Link: https://lore.kernel.org/r/20201211042420.16411-1-po-hsu.lin@canonical.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit 0e12c0271887f1b00b79b7612c1d4f0d3d34e8a8) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Kamal Mostafa [Thu, 17 Dec 2020 19:32:58 +0000 (11:32 -0800)]
UBUNTU: upstream stable to v5.4.82
BugLink: https://bugs.launchpad.net/bugs/1908564
Ignore: yes Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
i40iw_mmap manipulates the vma->vm_pgoff to differentiate a push page mmap
vs a doorbell mmap, and uses it to compute the pfn in remap_pfn_range
without any validation. This is vulnerable to an mmap exploit as described
in: https://lore.kernel.org/r/20201119093523.7588-1-zhudi21@huawei.com
The push feature is disabled in the driver currently and therefore no push
mmaps are issued from user-space. The feature does not work as expected in
the x722 product.
Remove the push module parameter and all VMA attribute manipulations for
this feature in i40iw_mmap. Update i40iw_mmap to only allow DB user
mmapings at offset = 0. Check vm_pgoff for zero and if the mmaps are bound
to a single page.
Cc: <stable@kernel.org> Fixes: d37498417947 ("i40iw: add files for iwarp interface") Link: https://lore.kernel.org/r/20201125005616.1800-2-shiraz.saleem@intel.com Reported-by: Di Zhu <zhudi21@huawei.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
triggers warning in dmesg:
WARNING: CPU: 3 PID: 1403 at kernel/trace/trace_hwlat.c:371 hwlat_tracer_start+0xc9/0xd0
Link: https://lkml.kernel.org/r/bd4d3e70-400d-9c82-7b73-a2d695e86b58@virtuozzo.com Cc: Ingo Molnar <mingo@redhat.com> Cc: stable@vger.kernel.org Fixes: 978defee11a5 ("tracing: Do a WARN_ON() if start_thread() in hwlat is called when thread exists") Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a08862 ("net/mlx5: Fix incorrect page count when in internal error") Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
STEs format for Connect-X5 and Connect-X6DX different. Currently, on
Connext-X6DX the SW steering would break at some point when building STEs
w/o giving a proper error message. Fix this by checking the STE format of
the current device when initializing domain: add mlx5_ifc definitions for
Connect-X6DX SW steering, read FW capability to get the current format
version, and check this version when domain is being created.
Fixes: 26d688e33f88 ("net/mlx5: DR, Add Steering entry (STE) utilities") Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
when 'act_mpls' is used to mangle the LSE, the current value is read from
the packet dereferencing 4 bytes at mpls_hdr(): ensure that the label is
contained in the skb "linear" area.
Found by code inspection.
v2:
- use MPLS_HLEN instead of sizeof(new_lse), thanks to Jakub Kicinski
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Guillaume Nault <gnault@redhat.com> Link: https://lore.kernel.org/r/3243506cba43d14858f3bd21ee0994160e44d64a.1606987058.git.dcaratti@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
when openvswitch is configured to mangle the LSE, the current value is
read from the packet dereferencing 4 bytes at mpls_hdr(): ensure that
the label is contained in the skb "linear" area.
Found by code inspection.
Fixes: d27cf5c59a12 ("net: core: add MPLS update core helper and use in OvS") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/aa099f245d93218b84b5c056b67b6058ccf81a66.1606987185.git.dcaratti@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
skb_mpls_dec_ttl() reads the LSE without ensuring that it is contained in
the skb "linear" area. Fix this calling pskb_may_pull() before reading the
current ttl.
Found by code inspection.
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/53659f28be8bc336c113b5254dc637cc76bbae91.1606987074.git.dcaratti@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return negative error code -ENOENT from invalid configuration
error handling case instead of 0, as done elsewhere in this function.
Fixes: 4bb043262878 ("net: mvpp2: phylink support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20201203141806.37966-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The "skb" is freed by the transmit code in cxgb4_ofld_send() and we
shouldn't use it again. But in the current code, if we hit an error
later on in the function then the clean up code will call kfree_skb(skb)
and so it causes a double free.
Set the "skb" to NULL and that makes the kfree_skb() a no-op.
Fixes: d25f2f71f653 ("crypto: chtls - Program the TLS session Key") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X8ilb6PtBRLWiSHp@mwanda Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: a9288525d2ae ("X25: Dont let x25_bind use addresses containing characters") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
syzkaller managed to crash the kernel using an NBMA ip6gre interface. I
could reproduce it creating an NBMA ip6gre interface and forwarding
traffic to it:
skbuff: skb_under_panic: text:ffffffff8250e927 len:148 put:44 head:ffff8c03c7a33
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:109!
Call Trace:
skb_push+0x10/0x10
ip6gre_header+0x47/0x1b0
neigh_connected_output+0xae/0xf0
ip6gre tunnel provides its own header_ops->create, and sets it
conditionally when initializing the tunnel in NBMA mode. When
header_ops->create is used, dev->hard_header_len should reflect the
length of the header created. Otherwise, when not used,
dev->needed_headroom should be used.
Fixes: eb95f52fc72d ("net: ipv6_gre: Fix GRO to work on IPv6 over GRE tap") Cc: Maria Pasechnik <mariap@mellanox.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20201130161911.464106-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When adding support for propagating ECT(1) marking in IP headers it seems I
suffered from endianness-confusion in the checksum update calculation: In
fact the ECN field is in the *lower* bits of the first 16-bit word of the
IP header when calculating in network byte order. This means that the
addition performed to update the checksum field was wrong; let's fix that.
Fixes: b723748750ec ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040") Reported-by: Jonathan Morton <chromatix99@gmail.com> Tested-by: Pete Heist <pete@heistp.net> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20201130183705.17540-1-toke@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Ensure that received Subordinate Command-Response Queue (SCRQ)
entries are properly read in order by the driver. These queues
are used in the ibmvnic device to process RX buffer and TX completion
descriptors. dma_rmb barriers have been added after checking for a
pending descriptor to ensure the correct descriptor entry is checked
and after reading the SCRQ descriptor to ensure the entire
descriptor is read before processing.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
there is kernel panic in inet_twsk_free() while chtls
module unload when socket is in TIME_WAIT state because
sk_prot_creator was not preserved on connection socket.
Fixes: cc35c88ae4db ("crypto : chtls - CPL handler definition") Signed-off-by: Udai Sharma <udai.sharma@chelsio.com> Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Link: https://lore.kernel.org/r/20201125214913.16938-1-vinay.yadav@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f8d ("NFC: pn544: i2c: Add DTS Documentation") Fixes: 6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver") Fixes: e3b329221567 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When inet_rtm_getroute() was converted to use the RCU variants of
ip_route_input() and ip_route_output_key(), the TOS parameters
stopped being masked with IPTOS_RT_MASK before doing the route lookup.
As a result, "ip route get" can return a different route than what
would be used when sending real packets.
For example:
$ ip route add 192.0.2.11/32 dev eth0
$ ip route add unreachable 192.0.2.11/32 tos 2
$ ip route get 192.0.2.11 tos 2
RTNETLINK answers: No route to host
But, packets with TOS 2 (ECT(0) if interpreted as an ECN bit) would
actually be routed using the first route:
$ ping -c 1 -Q 2 192.0.2.11
PING 192.0.2.11 (192.0.2.11) 56(84) bytes of data.
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.173 ms
--- 192.0.2.11 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.173/0.173/0.173/0.000 ms
This patch re-applies IPTOS_RT_MASK in inet_rtm_getroute(), to
return results consistent with real route lookups.
Fixes: 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/b2d237d08317ca55926add9654a48409ac1b8f5b.1606412894.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Florian Westphal <fw@strlen.de> Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Although not exactly identical, unthrottle_cfs_rq() and enqueue_task_fair()
are quite close and follow the same sequence for enqueuing an entity in the
cfs hierarchy. Modify unthrottle_cfs_rq() to use the same pattern as
enqueue_task_fair(). This fixes a problem already faced with the latter and
add an optimization in the last for_each_sched_entity loop.
Fixes: fe61468b2cb (sched/fair: Fix enqueue_task_fair warning)
Reported-by Tao Zhou <zohooouoto@zoho.com.cn> Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Phil Auld <pauld@redhat.com> Reviewed-by: Ben Segall <bsegall@google.com> Link: https://lkml.kernel.org/r/20200513135528.4742-1-vincent.guittot@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Registers 8-9 are used to store measurements of the kernel and its
command line (e.g., grub2 bootloader with tpm module enabled). IMA
should include them in the boot aggregate. Registers 8-9 should be
only included in non-SHA1 digests to avoid ambiguity.
Signed-off-by: Maurizio Drocco <maurizio.drocco@ibm.com> Reviewed-by: Bruno Meneguele <bmeneg@redhat.com> Tested-by: Bruno Meneguele <bmeneg@redhat.com> (TPM 1.2, TPM 2.0) Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
There's a semantic conflict in the Octeon staging network driver, which
used the skb_reset_tc() function to reset skb state when re-using an
skb. But that inline helper function was removed in mainline by commit 2c64605b590e ("net: Fix CONFIG_NET_CLS_ACT=n and
CONFIG_NFT_FWD_NETDEV={y, m} build").
Fix it by using skb_reset_redirect() instead. Also move it out of the
This code path only ends up triggering if REUSE_SKBUFFS_WITHOUT_FREE is
enabled, which in turn only happens if you don't have CONFIG_NETFILTER
configured. Which was how this wasn't caught by the usual allmodconfig
builds.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
This is a potential use-after-free if the sysfs nodes are being accessed
whilst removing the struct slave, so wait for the object destruction to
complete before freeing the struct slave itself.
Fixes: 07699f9a7c8d ("bonding: add sysfs /slave dir for bond slave devices.") Fixes: a068aab42258 ("bonding: Fix reference count leak in bond_sysfs_slave_add.") Cc: Qiushi Wu <wu000273@umn.edu> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jamie Iles <jamie@nuviainc.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20201120142827.879226-1-jamie@nuviainc.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
tun only checks the file O_NONBLOCK flag, but it should also be checking
the iocb IOCB_NOWAIT flag. Any fops using ->read/write_iter() should check
both, otherwise it breaks users that correctly expect O_NONBLOCK semantics
if IOCB_NOWAIT is set.
Signed-off-by: Jens Axboe <axboe@kernel.dk> Link: https://lore.kernel.org/r/e9451860-96cc-c7c7-47b8-fe42cadd5f4c@kernel.dk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When setting congestion control via a BPF program it is seen that the
SYN/ACK for packets within a given flow will not include the ECT0 flag. A
bit of simple printk debugging shows that when this is configured without
BPF we will see the value INET_ECN_xmit value initialized in
tcp_assign_congestion_control however when we configure this via BPF the
socket is in the closed state and as such it isn't configured, and I do not
see it being initialized when we transition the socket into the listen
state. The result of this is that the ECT0 bit is configured based on
whatever the default state is for the socket.
Any easy way to reproduce this is to monitor the following with tcpdump:
tools/testing/selftests/bpf/test_progs -t bpf_tcp_ca
Without this patch the SYN/ACK will follow whatever the default is. If dctcp
all SYN/ACK packets will have the ECT0 bit set, and if it is not then ECT0
will be cleared on all SYN/ACK packets. With this patch applied the SYN/ACK
bit matches the value seen on the other packets in the given stream.
Fixes: 91b5b21c7c16 ("bpf: Add support for changing congestion control") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When setting sk_err, set it to ee_errno, not ee_origin.
Commit f5f99309fa74 ("sock: do not set sk_err in
sock_dequeue_err_skb") disabled updating sk_err on errq dequeue,
which is correct for most error types (origins):
- sk->sk_err = err;
Commit 38b257938ac6 ("sock: reset sk_err when the error queue is
empty") reenabled the behavior for IMCP origins, which do require it:
+ if (icmp_next)
+ sk->sk_err = SKB_EXT_ERR(skb_next)->ee.ee_origin;
But read from ee_errno.
Fixes: 38b257938ac6 ("sock: reset sk_err when the error queue is empty") Reported-by: Ayush Ranjan <ayushranjan@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Link: https://lore.kernel.org/r/20201126151220.2819322-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
rose_send_frame() dereferences `neigh->dev` when called from
rose_transmit_clear_request(), and the first occurrence of the
`neigh` is in rose_loopback_timer() as `rose_loopback_neigh`,
and it is initialized in rose_add_loopback_neigh() as NULL.
i.e when `rose_loopback_neigh` used in rose_loopback_timer()
its `->dev` was still NULL and rose_loopback_timer() was calling
rose_rx_call_request() without checking for NULL.
- net/rose/rose_link.c
This bug seems to get triggered in this line:
rose_call = (ax25_address *)neigh->dev->dev_addr;
Fix it by adding NULL checking for `rose_loopback_neigh->dev`
in rose_loopback_timer().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Suggested-by: Jakub Kicinski <kuba@kernel.org> Reported-by: syzbot+a1c743815982d9496393@syzkaller.appspotmail.com Tested-by: syzbot+a1c743815982d9496393@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=9d2a7ca8c7f2e4b682c97578dfa3f236258300b3 Signed-off-by: Anmol Karn <anmol.karan123@gmail.com> Link: https://lore.kernel.org/r/20201119191043.28813-1-anmol.karan123@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
tls_device_offload_cleanup_rx doesn't clear tls_ctx->netdev after
calling tls_dev_del if TLX TX offload is also enabled. Clearing
tls_ctx->netdev gets postponed until tls_device_gc_task. It leaves a
time frame when tls_device_down may get called and call tls_dev_del for
RX one extra time, confusing the driver, which may lead to a crash.
This patch corrects this racy behavior by adding a flag to prevent
tls_device_down from calling tls_dev_del the second time.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20201125221810.69870-1-saeedm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In case when tcp socket received FIN after some data and the
parser haven't started before reading data caller will receive
an empty buffer. This behavior differs from plain TCP socket and
leads to special treating in user-space.
The flow that triggers the race is simple. Server sends small
amount of data right after the connection is configured to use TLS
and closes the connection. In this case receiver sees TLS Handshake
data, configures TLS socket right after Change Cipher Spec record.
While the configuration is in process, TCP socket receives small
Application Data record, Encrypted Alert record and FIN packet. So
the TCP socket changes sk_shutdown to RCV_SHUTDOWN and sk_flag with
SK_DONE bit set. The received data is not parsed upon arrival and is
never sent to user-space.
Patch unpauses parser directly if we have unparsed data in tcp
receive queue.
Fixes: fcf4793e278e ("tls: check RCV_SHUTDOWN in tls_wait_data") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1605801588-12236-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Child sockets erroneously inherit their parent's sk_type (ie. SOCK_*),
instead of the PF_IUCV protocol that the parent was created with in
iucv_sock_create().
We're currently not using sk->sk_protocol ourselves, so this shouldn't
have much impact (except eg. getting the output in skb_dump() right).
Fixes: eac3731bd04c ("[S390]: Add AF_IUCV socket support") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Link: https://lore.kernel.org/r/20201120100657.34407-1-jwi@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
We should free all rules when we catch an error in ip6addrlbl_net_init().
otherwise a memory leak will occur.
Fixes: 2a8cc6c89039 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20201124071728.8385-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
A netdevice of a devlink port can be moved to different net namespace
than its parent devlink instance.
This scenario occurs when devlink reload is not used.
When netdevice is undergoing migration to net namespace, its ifindex
and name may change.
In such use case, devlink port query may read stale netdev attributes.
Fix it by reading them under rtnl lock.
Fixes: bfcd3a466172 ("Introduce devlink infrastructure") Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Kamal Mostafa [Thu, 17 Dec 2020 19:27:21 +0000 (11:27 -0800)]
UBUNTU: upstream stable to v5.4.81
BugLink: https://bugs.launchpad.net/bugs/1908562
Ignore: yes Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Automatically choose DMIC pipeline format configuration depending on
information included in NHLT.
Change the access rights of appropriate kcontrols to read-only in order
to prevent user interference.
Signed-off-by: Mateusz Gorski <mateusz.gorski@linux.intel.com> Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200427132727.24942-4-mateusz.gorski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Cc: <stable@vger.kernel.org> # 5.4.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
For pipes supporting multiple input/output formats, kcontrol is
created and selection of pipe input and output configuration
is done based on control set.
If more than one configuration is supported, then this patch
allows user to select configuration of choice
using amixer settings.
Signed-off-by: Mateusz Gorski <mateusz.gorski@linux.intel.com> Signed-off-by: Pavan K S <pavan.k.s@intel.com> Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200427132727.24942-3-mateusz.gorski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Cc: <stable@vger.kernel.org> # 5.4.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>