Add rate limiting of the 'pp done time out' warnings since these
warnings can quickly fill the dmesg buffer.
Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)
Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.
Signed-off-by: Sergey Organov <sorganov@gmail.com> Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().
Otherwise undefined behavior might occur.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:
- usb_gadget_vbus_draw() when called from set_config() and
composite_resume() will be passed the MaxPower value without
regard for the current connection speed, resulting in a
violation for USB 2.0 since the max is 500mA.
- the bMaxPower of the configuration descriptor would be
incorrectly encoded, again if the connection speed is only
at USB 2.0 or below, likely wrapping around U8_MAX since
the 2mA multiplier corresponds to a maximum of 510mA.
Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.
Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.
N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.
Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:
make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127
Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)
Also, separate handling of each of the lists to its own shell command.
The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
optimize_kprobe() and unoptimize_kprobe() cancels if a given kprobe
is on the optimizing_list or unoptimizing_list already. However, since
the following commit:
f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code")
modified the update timing of the KPROBE_FLAG_OPTIMIZED, it doesn't
work as expected anymore.
The optimized_kprobe could be in the following states:
- [optimizing]: Before inserting jump instruction
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is not empty.
- [optimized]: jump inserted
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is empty.
- [unoptimizing]: Before removing jump instruction (including unused
optprobe)
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is not empty.
- [unoptimized]: jump removed
op.kp->flags doesn't have KPROBE_FLAG_OPTIMIZED and
op->list is empty.
Current code mis-expects [unoptimizing] state doesn't have
KPROBE_FLAG_OPTIMIZED, and that can cause incorrect results.
To fix this, introduce optprobe_queued_unopt() to distinguish [optimizing]
and [unoptimizing] states and fixes the logic in optimize_kprobe() and
unoptimize_kprobe().
[ mingo: Cleaned up the changelog and the code a bit. ]
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bristot@redhat.com Fixes: f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code") Link: https://lkml.kernel.org/r/157840814418.7181.13478003006386303481.stgit@devnote2 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When port is part of the modify mask, then we should take it from the
qp_attr and not from the old pps. Same for PKEY. Otherwise there are
panics in some configurations:
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec") Fixes: de34d7084edd ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Doing so, we save one call to get data we already have in the struct.
Also, since there is no guarantee that getname use sockaddr_ll
parameter beyond its size, we add a little bit of security here.
It should do not do beyond MAX_ADDR_LEN, but syzbot found that
ax25_getname writes more (72 bytes, the size of full_sockaddr_ax25,
versus 20 + 32 bytes of sockaddr_ll + MAX_ADDR_LEN in syzbot repro).
Fixes: 3a4d5c94e9593 ("vhost_net: a kernel-level virtio server") Reported-by: syzbot+f2a62d07a5198c819c7b@syzkaller.appspotmail.com Signed-off-by: Eugenio Pérez <eperezma@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[jwang: backport to 4.14] Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If thp defrag setting "defer" is used and a newline is *not* used when
writing to the sysfs file, this is interpreted as the "defer+madvise"
option.
This is because we do prefix matching and if five characters are written
without a newline, the current code ends up comparing to the first five
bytes of the "defer+madvise" option and using that instead.
Use the more appropriate sysfs_streq() that handles the trailing newline
for us. Since this doubles as a nice cleanup, do it in enabled_store()
as well.
The current implementation relies on prefix matching: the number of
bytes compared is either the number of bytes written or the length of
the option being compared. With a newline, "defer\n" does not match
"defer+"madvise"; without a newline, however, "defer" is considered to
match "defer+madvise" (prefix matching is only comparing the first five
bytes). End result is that writing "defer" is broken unless it has an
additional trailing character.
This means that writing "madv" in the past would match and set
"madvise". With strict checking, that no longer is the case but it is
unlikely anybody is currently doing this.
Link: http://lkml.kernel.org/r/alpine.DEB.2.21.2001171411020.56385@chino.kir.corp.google.com Fixes: 21440d7eb904 ("mm, thp: add new defer+madvise defrag option") Signed-off-by: David Rientjes <rientjes@google.com> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We need to set actions->ms.map since 599a2f38a989 ("perf hists browser:
Check sort keys before hot key actions"), as in that patch we bail out
if map is NULL.
Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 599a2f38a989 ("perf hists browser: Check sort keys before hot key actions") Link: https://lkml.kernel.org/n/tip-wp1ssoewy6zihwwexqpohv0j@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Set the unoptimized flag after confirming the code is completely
unoptimized. Without this fix, when a kprobe hits the intermediate
modified instruction (the first byte is replaced by an INT3, but
later bytes can still be a jump address operand) while unoptimizing,
it can return to the middle byte of the modified code, which causes
an invalid instruction exception in the kernel.
Usually, this is a rare case, but if we put a probe on the function
call while text patching, it always causes a kernel panic as below:
text_poke() is used for patching the code in optprobes.
This can happen even if we blacklist text_poke() and other functions,
because there is a small time window during which we show the intermediate
code to other CPUs.
[ mingo: Edited the changelog. ]
Tested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bristot@redhat.com Fixes: 6274de4984a6 ("kprobes: Support delayed unoptimizing") Link: https://lkml.kernel.org/r/157483422375.25881.13508326028469515760.stgit@devnote2 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When reading/writing using the guest/host cache, check for a bad hva
before checking for a NULL memslot, which triggers the slow path for
handing cross-page accesses. Because the memslot is nullified on error
by __kvm_gfn_to_hva_cache_init(), if the bad hva is encountered after
crossing into a new page, then the kvm_{read,write}_guest() slow path
could potentially write/access the first chunk prior to detecting the
bad hva.
Arguably, performing a partial access is semantically correct from an
architectural perspective, but that behavior is certainly not intended.
In the original implementation, memslot was not explicitly nullified
and therefore the partial access behavior varied based on whether the
memslot itself was null, or if the hva was simply bad. The current
behavior was introduced as a seemingly unintentional side effect in
commit f1b9dd5eb86c ("kvm: Disallow wraparound in
kvm_gfn_to_hva_cache_init"), which justified the change with "since some
callers don't check the return code from this function, it sit seems
prudent to clear ghc->memslot in the event of an error".
Regardless of intent, the partial access is dependent on _not_ checking
the result of the cache initialization, which is arguably a bug in its
own right, at best simply weird.
Fixes: 8f964525a121 ("KVM: Allow cross page reads and writes from cached translations.") Cc: Jim Mattson <jmattson@google.com> Cc: Andrew Honig <ahonig@google.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The KVM MMIO support uses bit 51 as the reserved bit to cause nested page
faults when a guest performs MMIO. The AMD memory encryption support uses
a CPUID function to define the encryption bit position. Given this, it is
possible that these bits can conflict.
Use svm_hardware_setup() to override the MMIO mask if memory encryption
support is enabled. Various checks are performed to ensure that the mask
is properly defined and rsvd_bits() is used to generate the new mask (as
was done prior to the change that necessitated this patch).
Fixes: 28a1f3ac1d0c ("kvm: x86: Set highest physical address bits in non-present/reserved SPTEs") Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before commit 1e58252e334d ("mwifiex: Fix heap overflow in
mmwifiex_process_tdls_action_frame()"),
mwifiex_process_tdls_action_frame() already had too many magic numbers.
But this commit just added a ton more, in the name of checking for
buffer overflows. That seems like a really bad idea.
Let's make these magic numbers a little less magic, by
(a) factoring out 'pos[1]' as 'ie_len'
(b) using 'sizeof' on the appropriate source or destination fields where
possible, instead of bare numbers
(c) dropping redundant checks, per below.
Regarding redundant checks: the beginning of the loop has this:
if (pos + 2 + pos[1] > end)
break;
but then individual 'case's include stuff like this:
if (pos > end - 3)
return;
if (pos[1] != 1)
return;
Note that the second 'return' (validating the length, pos[1]) combined
with the above condition (ensuring 'pos + 2 + length' doesn't exceed
'end'), makes the first 'return' (whose 'if' can be reworded as 'pos >
end - pos[1] - 2') redundant. Rather than unwind the magic numbers
there, just drop those conditions.
Fixes: 1e58252e334d ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It's over-zealous to return hard errors under RCU-walk here, given that
a REF-walk will be triggered for all other cases handling ".." under
RCU.
The original purpose of this check was to ensure that if a rename occurs
such that a directory is moved outside of the bind-mount which the
resolution started in, it would be detected and blocked to avoid being
able to mess with paths outside of the bind-mount. However, triggering a
new REF-walk is just as effective a solution.
Cc: "Eric W. Biederman" <ebiederm@xmission.com> Fixes: 397d425dc26d ("vfs: Test for and handle paths that are unreachable from their mnt_root") Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Aleksa Sarai <cyphar@cyphar.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Code inspection found that in case of mapping error we do return current
'ret' value. But beside error, it is used to count number of descriptors
allocated for the packet. In that case map_skb function could return '1'.
Changing it to return zero (number of mapped descriptors for skb)
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since nl_groups is a u32 we can't bind more groups via ->bind
(netlink_bind) call, but netlink has supported more groups via
setsockopt() for a long time and thus nlk->ngroups could be over 32.
Recently I added support for per-vlan notifications and increased the
groups to 33 for NETLINK_ROUTE which exposed an old bug in the
netlink_bind() code causing out-of-bounds access on archs where unsigned
long is 32 bits via test_bit() on a local variable. Fix this by capping the
maximum groups in netlink_bind() to BITS_PER_TYPE(u32), effectively
capping them at 32 which is the minimum of allocated groups and the
maximum groups which can be bound via netlink_bind().
CC: Christophe Leroy <christophe.leroy@c-s.fr> CC: Richard Guy Briggs <rgb@redhat.com> Fixes: 4f520900522f ("netlink: have netlink per-protocol bind function return an error code.") Reported-by: Erhard F. <erhard_f@mailbox.org> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1868623
When doing the 4.9 merge into certain Android trees, I noticed a warning
from Android's deprecated GCC 4.9.4, which causes a build failure in
those trees due to basically -Werror:
fs/ecryptfs/keystore.c: In function 'ecryptfs_parse_packet_set':
fs/ecryptfs/keystore.c:1357:2: warning: 'auth_tok_list_item' may be used
uninitialized in this function [-Wmaybe-uninitialized]
memset(auth_tok_list_item, 0,
^
fs/ecryptfs/keystore.c:1260:38: note: 'auth_tok_list_item' was declared
here
struct ecryptfs_auth_tok_list_item *auth_tok_list_item;
^
GCC 9.2.0 was not able to pick up this warning when I tested it.
Turns out that Clang warns as well when -Wuninitialized is used, which
is not the case in older stable trees at the moment (but shows value in
potentially backporting the various warning fixes currently in upstream
to get more coverage).
fs/ecryptfs/keystore.c:1284:6: warning: variable 'auth_tok_list_item' is
used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (data[(*packet_size)++] != ECRYPTFS_TAG_1_PACKET_TYPE) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/ecryptfs/keystore.c:1360:4: note: uninitialized use occurs here
auth_tok_list_item);
^~~~~~~~~~~~~~~~~~
fs/ecryptfs/keystore.c:1284:2: note: remove the 'if' if its condition is
always false
if (data[(*packet_size)++] != ECRYPTFS_TAG_1_PACKET_TYPE) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/ecryptfs/keystore.c:1260:56: note: initialize the variable
'auth_tok_list_item' to silence this warning
struct ecryptfs_auth_tok_list_item *auth_tok_list_item;
^
= NULL
1 warning generated.
Somehow, commit fe2e082f5da5 ("ecryptfs: fix a memory leak bug in
parse_tag_1_packet()") upstream was not applied in the correct if block
in 4.4.215, 4.9.215, and 4.14.172, which will indeed lead to use of
uninitialized memory. Fix it up by undoing the bad backport in those
trees then reapplying the patch in the proper location.
ALL_ENGINES reset doesn't clobber display with the current gvt-g
supported platforms. Thus ALL_ENGINES reset shouldn't reset the
display engine registers emulated by gvt-g.
The printout for txabrt is way too talkative and is highly annoying with
scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest
can be gained by I2C core debugging and datasheet information. Also,
make it a debug printout, it won't help the regular user.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Pointer on the memory allocated by 'alloc_progmem()' is stored in
'v->load_addr'. So this is this memory that should be freed by
'release_progmem()'.
'release_progmem()' is only a call to 'kfree()'.
With the current code, there is both a double free and a memory leak.
Fix it by passing the correct pointer to 'release_progmem()'.
Fixes: e01402b115ccc ("More AP / SP bits for the 34K, the Malta bits and things. Still wants") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: ralf@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: kernel-janitors@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Syzbot reports that "hiddev" is used after it's free in hiddev_disconnect().
The hiddev_disconnect() function sets "hiddev->exist = 0;" so
hiddev_release() can free it as soon as we drop the "existancelock"
lock. This patch moves the mutex_unlock(&hiddev->existancelock) until
after we have finished using it.
The name changing as devfreq(X) breaks some user space applications,
such as Android HAL from Unisoc and Hikey [1].
The device name will be changed unexpectly after every boot depending
on module init sequence. It will make trouble to setup some system
configuration like selinux for Android.
So we'd like to revert it back to old naming rule before any better
way being found.
The tracing seftests checks various aspects of the tracing infrastructure,
and one is filtering. If trace_printk() is active during a self test, it can
cause the filtering to fail, which will disable that part of the trace.
To keep the selftests from failing because of trace_printk() calls,
trace_printk() checks the variable tracing_selftest_running, and if set, it
does not write to the tracing buffer.
As some tracers were registered earlier in boot, the selftest they triggered
would fail because not all the infrastructure was set up for the full
selftest. Thus, some of the tests were post poned to when their
infrastructure was ready (namely file system code). The postpone code did
not set the tracing_seftest_running variable, and could fail if a
trace_printk() was added and executed during their run.
Cc: stable@vger.kernel.org Fixes: 9afecfbb95198 ("tracing: Postpone tracer start-up tests till the system is more robust") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We have a HID touch device that reports its opens and shorts test
results in HID buffers of size 8184 bytes. The maximum size of the HID
buffer is currently set to 4096 bytes, causing probe of this device to
fail. With this patch we increase the maximum size of the HID buffer to
8192 bytes, making device probe and acquisition of said buffers succeed.
In case a report is greater than HID_MAX_BUFFER_SIZE, it is truncated,
but the report-number byte is not correctly handled. This results in a
off-by-one in the following memset, causing a kernel Oops and ensuing
system crash.
Note: With commit 8ec321e96e05 ("HID: Fix slab-out-of-bounds read in
hid_field_extract") I no longer hit the kernel Oops as we instead fail
"controlled" at probe if there is a report too long in the HID
report-descriptor. hid_report_raw_event() is an exported symbol, so
presumabely we cannot always rely on this being the case.
Fixes: 966922f26c7f ("HID: fix a crash in hid_report_raw_event()
function.") Signed-off-by: Johan Korsnes <jkorsnes@cisco.com> Cc: Armando Visconti <armando.visconti@st.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 8f18eca9ebc5 ("HID: ite: Add USB id match for Acer SW5-012 keyboard
dock") added the USB id for the Acer SW5-012's keyboard dock to the
hid-ite driver to fix the rfkill driver not working.
Most keyboard docks with an ITE 8595 keyboard/touchpad controller have the
"Wireless Radio Control" bits which need the special hid-ite driver on the
second USB interface (the mouse interface) and their touchpad only supports
mouse emulation, so using generic hid-input handling for anything but
the "Wireless Radio Control" bits is fine. On these devices we simply bind
to all USB interfaces.
But unlike other ITE8595 using keyboard docks, the Acer Aspire Switch 10
(SW5-012)'s touchpad not only does mouse emulation it also supports
HID-multitouch and all the keys including the "Wireless Radio Control"
bits have been moved to the first USB interface (the keyboard intf).
So we need hid-ite to handle the first (keyboard) USB interface and have
it NOT bind to the second (mouse) USB interface so that that can be
handled by hid-multitouch.c and we get proper multi-touch support.
This commit changes the hid_device_id for the SW5-012 keyboard dock to
only match on hid devices from the HID_GROUP_GENERIC group, this way
hid-ite will not bind the the mouse/multi-touch interface which has
HID_GROUP_MULTITOUCH_WIN_8 as group.
This fixes the regression to mouse-emulation mode introduced by adding
the keyboard dock USB id.
Cc: stable@vger.kernel.org Fixes: 8f18eca9ebc5 ("HID: ite: Add USB id match for Acer SW5-012 keyboard dock") Reported-by: Zdeněk Rampas <zdenda.rampas@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
KVM emulates UMIP on hardware that doesn't support it by setting the
'descriptor table exiting' VM-execution control and performing
instruction emulation. When running nested, this emulation is broken as
KVM refuses to emulate L2 instructions by default.
Correct this regression by allowing the emulation of descriptor table
instructions if L1 hasn't requested 'descriptor table exiting'.
Fixes: 07721feee46b ("KVM: nVMX: Don't emulate instructions in guest mode") Reported-by: Jan Kiszka <jan.kiszka@web.de> Cc: stable@vger.kernel.org Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Oliver Upton <oupton@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ACPI Generic Address Structure (GAS) access_width field is not in bytes
as the driver seems to expect in few places so fix this by using the
newly introduced macro ACPI_ACCESS_BYTE_WIDTH().
Fixes: b1abf6fc4982 ("ACPI / watchdog: Fix off-by-one error at resource assignment") Fixes: 058dfc767008 ("ACPI / watchdog: Add support for WDAT hardware watchdog") Reported-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 219ca39427bf ("audit: use union for audit_field values since
they are mutually exclusive") combined a number of separate fields in
the audit_field struct into a single union. Generally this worked
just fine because they are generally mutually exclusive.
Unfortunately in audit_data_to_entry() the overlap can be a problem
when a specific error case is triggered that causes the error path
code to attempt to cleanup an audit_field struct and the cleanup
involves attempting to free a stored LSM string (the lsm_str field).
Currently the code always has a non-NULL value in the
audit_field.lsm_str field as the top of the for-loop transfers a
value into audit_field.val (both .lsm_str and .val are part of the
same union); if audit_data_to_entry() fails and the audit_field
struct is specified to contain a LSM string, but the
audit_field.lsm_str has not yet been properly set, the error handling
code will attempt to free the bogus audit_field.lsm_str value that
was set with audit_field.val at the top of the for-loop.
This patch corrects this by ensuring that the audit_field.val is only
set when needed (it is cleared when the audit_field struct is
allocated with kcalloc()). It also corrects a few other issues to
ensure that in case of error the proper error code is returned.
Cc: stable@vger.kernel.org Fixes: 219ca39427bf ("audit: use union for audit_field values since they are mutually exclusive") Reported-by: syzbot+1f4d90ead370d72e450b@syzkaller.appspotmail.com Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If sbi->s_flex_groups_allocated is zero and the first allocation fails
then this code will crash. The problem is that "i--" will set "i" to
-1 but when we compare "i >= sbi->s_flex_groups_allocated" then the -1
is type promoted to unsigned and becomes UINT_MAX. Since UINT_MAX
is more than zero, the condition is true so we call kvfree(new_groups[-1]).
The loop will carry on freeing invalid memory until it crashes.
tc flower rules that are based on src or dst port blocking are sometimes
ineffective due to uninitialized stack data. __skb_flow_dissect() extracts
ports from the skb for tc flower to match against. However, the port
dissection is not done when when the FLOW_DIS_IS_FRAGMENT bit is set in
key_control->flags. All callers of __skb_flow_dissect(), zero-out the
key_control field except for fl_classify() as used by the flower
classifier. Thus, the FLOW_DIS_IS_FRAGMENT may be set on entry to
__skb_flow_dissect(), since key_control is allocated on the stack
and may not be initialized.
Since key_basic and key_control are present for all flow keys, let's
make sure they are initialized.
Fixes: 62230715fd24 ("flow_dissector: do not dissect l4 ports for fragments") Co-developed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If an event is added while the rdma workqueue is being destroyed
it could lead to several races, list corruption, null pointer
dereference during queue_work or init_queue.
This fixes the race between the two flows which can occur during
shutdown.
A kref object and a completion object are added to the rdma_dev
structure, these are initialized before the workqueue is created.
The refcnt is used to indicate work is being added to the
workqueue and ensures the cleanup flow won't start while we're in
the middle of adding the event.
Once the work is added, the refcnt is decreased and the cleanup flow
is safe to run.
Fixes: cee9fbd8e2e ("qede: Add qedr framework") Signed-off-by: Ariel Elior <ariel.elior@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After commit 27596472473a ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When splitting an RTA_MULTIPATH request into multiple routes and adding the
second and later components, we must not simply remove NLM_F_REPLACE but
instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink
message was malformed.
For example,
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \
nexthop via fe80::30:2 dev dummy0
results in the following warnings:
[ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE
[ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route
This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to
what it would get if the multipath route had been added in multiple netlink
operations:
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0
ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0
Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When T2 timer is to be stopped, the asoc should also be deleted,
otherwise, there will be no chance to call sctp_association_free
and the asoc could last in memory forever.
However, in sctp_sf_shutdown_sent_abort(), after adding the cmd
SCTP_CMD_TIMER_STOP for T2 timer, it may return error due to the
format error from __sctp_sf_do_9_1_abort() and miss adding
SCTP_CMD_ASSOC_FAILED where the asoc will be deleted.
This patch is to fix it by moving the format error check out of
__sctp_sf_do_9_1_abort(), and do it before adding the cmd
SCTP_CMD_TIMER_STOP for T2 timer.
Thanks Hangbin for reporting this issue by the fuzz testing.
v1->v2:
- improve the comment in the code as Marcelo's suggestion.
Fixes: 96ca468b86b0 ("sctp: check invalid value of length parameter in error cause") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The PN544 driver checks the "enable" polarity during of driver's probe and
it's doing that by turning ON and OFF NFC with different polarities until
enabling succeeds. It takes some time for the hardware to power-down, and
thus, to deassert the IRQ that is raised by turning ON the hardware.
Since the delay after last power-down of the polarity-checking process is
missed in the code, the interrupt may trigger immediately after installing
the IRQ handler (right after the checking is done), which results in IRQ
handler trying to touch the disabled HW and ends with marking NFC as
'DEAD' during of the driver's probe:
pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high
pn544_hci_i2c 1-002a: NFC: invalid len byte
shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead
This patch fixes the occasional NFC initialization failure on Nexus 7
device.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The mii management register in iproc mdio block
does not have a retention register so it is lost on suspend.
Save and restore value of register while resuming from suspend.
Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In 709772e6e06564ed94ba740de70185ac3d792773, RT_TABLE_COMPAT was added to
allow legacy software to deal with routing table numbers >= 256, but the
same change to FIB rule queries was overlooked.
Signed-off-by: Jethro Beekman <jethro@fortanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The commit 97f5f0cd8cd0a0544 ("Input: implement SysRq as a separate input
handler") added pr_fmt() definition. It caused a duplicated message
prefix in the sysrq header messages, for example:
[ 177.053931] sysrq: SysRq : Show backtrace of all active CPUs
[ 742.864776] sysrq: SysRq : HELP : loglevel(0-9) reboot(b) crash(c)
Fixes: 97f5f0cd8cd0a05 ("Input: implement SysRq as a separate input handler") Signed-off-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The sysrq header line is printed with an increased loglevel
to provide users some positive feedback.
The original loglevel is not restored when the sysrq operation
is disabled. This bug was introduced in 2.6.12 (pre-git-history)
by the commit ("Allow admin to enable only some of the Magic-Sysrq
functions").
Signed-off-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A number of the debug statements output file or directory mode
in hex. Change these to print using octal.
Signed-off-by: Frank Sorenson <sorenson@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Bug description:
When running "ethtool -x <if_name>" the key shows up as all zeros.
When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to
set the key and then try to retrieve it using "ethtool -x <if_name>" then
we return the correct key because we return the one we saved.
Bug cause:
We don't fetch the key from the device but instead return the key
that we have saved internally which is by default set to zero upon
allocation.
Fix:
This commit fixes the issue by initializing the key to a random value
using netdev_rss_key_fill().
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current implementation of the driver calls skb_tx_timestamp()to add a
software tx timestamp to the skb, however the software-transmit capability
is not reported in ethtool -T.
This commit updates the ethtool structure to report the software-transmit
capability in ethtool -T using the standard ethtool_op_get_ts_info().
This function reports all software timestamping capabilities (tx and rx),
as well as setting phc_index = -1. phc_index is the index of the PTP
hardware clock device that will be used for hardware timestamps. Since we
don't have such a device in ENA, using the default -1 value is the correct
setting.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
>From the documentation of round_jiffies():
"Rounds a time delta in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."
There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.
Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().
Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.
Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().
Fixes: 82ef30f13be0 ("net: ena: add hardware hints capability to the driver") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <kristian.evensen@gmail.com> Cc: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit f25e1392fdb5 removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware") Link: https://whrl.pl/Rf0vNk Reported-by: Lars Melin <larsm17@gmail.com> Cc: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When preparing ethtool drvinfo, check if wiphy driver is defined
before dereferencing it. Driver may not exist, e.g. if wiphy is
attached to a virtual platform device.
We only use the parsing CRC for checking if a beacon changed,
and elements with an ID > 63 cannot be represented in the
filter. Thus, like we did before with WMM and Cisco vendor
elements, just statically add these forgotten items to the
CRC:
- WLAN_EID_VHT_OPERATION
- WLAN_EID_OPMODE_NOTIF
I guess that in most cases when VHT/HE operation change, the HT
operation also changed, and so the change was picked up, but we
did notice that pure operating mode notification changes were
ignored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20200131111300.891737-22-luca@coelho.fi
[restrict to VHT for the mac80211 branch] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
fstests generic/471 reports a failure when run with MOUNT_OPTIONS="-o
dax". The reason is that the initial pwrite to an empty file with the
RWF_NOWAIT flag set does not return -EAGAIN. It turns out that
dax_iomap_rw doesn't pass that flag through to iomap_apply.
With this patch applied, generic/471 passes for me.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/x49r1z86e1d.fsf@segfault.boston.devel.redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The root of the problem is that the default segment size for sgt is
(UINT_MAX & PAGE_MASK), and the default segment size for device dma is
64K. As such, if you compare the 2, you would deduce that the sg segment
will overflow the device's capacity. In reality, the hardware can
accommodate the larger sg segments, it's just not initializing its max
segment properly. This patch initializes the max segment size for the
mdss device, which gets rid of that pesky warning.
Reported-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200121111813.REPOST.1.I92c66a35fb13f368095b05287bdabdbe88ca6922@changeid Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In error cases a NULL can be passed to memcpy. The length will always
be zero, so it doesn't really matter, but go ahead and check for NULL,
anyway, to be more precise and avoid static analysis errors.
During an online resize an array of pointers to s_group_info gets replaced
so it can get enlarged. If there is a concurrent access to the array in
ext4_get_group_info() and this memory has been reused then this can lead to
an invalid memory access.
During an online resize an array of s_flex_groups structures gets replaced
so it can get enlarged. If there is a concurrent access to the array and
this memory has been reused then this can lead to an invalid memory access.
The s_flex_group array has been converted into an array of pointers rather
than an array of structures. This is to ensure that the information
contained in the structures cannot get out of sync during a resize due to
an accessor updating the value in the old structure after it has been
copied but before the array pointer is updated. Since the structures them-
selves are no longer copied but only the pointers to them this case is
mitigated.
During an online resize an array of pointers to buffer heads gets
replaced so it can get enlarged. If there is a racing block
allocation or deallocation which uses the old array, and the old array
has gotten reused this can lead to a GPF or some other random kernel
memory getting modified.
We don't handle failures in the rb_allocator workqueue allocation
correctly. To fix that, move the code earlier so the cleanup is
easier and we don't have to undo all the interrupt allocations in
this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[Ajay: Modified to apply on v4.19.y and v4.14.y] Signed-off-by: Ajay Kaher <akaher@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
clang 10 introduces -mpacked-stack compiler option implementation. At the
same time currently it does not support a combination of -mpacked-stack
and -mbackchain. This leads to the following build error:
clang: error: unsupported option '-mpacked-stack with -mbackchain' for
target 's390x-ibm-linux'
If/when clang adds support for a combination of -mpacked-stack and
-mbackchain it would also require -msoft-float (like gcc does). According
to Ulrich Weigand "stack slot assigned to the kernel backchain overlaps
the stack slot assigned to the FPR varargs (both are required to be
placed immediately after the saved r15 slot if present)."
Extend -mpacked-stack compiler option support check to include all 3
options -mpacked-stack -mbackchain -msoft-float which must present to
support -mpacked-stack with -mbackchain.
drivers/gpu/drm/nouveau/nouveau_ttm.c: In function nouveau_vram_manager_new:
drivers/gpu/drm/nouveau/nouveau_ttm.c:66:22: warning: variable mem set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/nouveau/nouveau_ttm.c: In function nouveau_gart_manager_new:
drivers/gpu/drm/nouveau/nouveau_ttm.c:106:22: warning: variable mem set but not used [-Wunused-but-set-variable]
They are not used any more, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The setup_crash_devices_work_queue function only partially initializes
the message it sends to chipset_init, leading to undefined behavior:
drivers/visorbus/visorchipset.c: In function 'setup_crash_devices_work_queue':
drivers/visorbus/visorchipset.c:333:6: error: '((unsigned char*)&msg.hdr.flags)[0]' is used uninitialized in this function [-Werror=uninitialized]
if (inmsg->hdr.flags.response_expected)
Set up the entire structure, zero-initializing the 'response_expected'
flag.
This was apparently found by the patch that added the -O3 build option
in Kconfig.
Fixes: 12e364b9f08a ("staging: visorchipset driver to provide registration and other services") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200107202950.782951-1-arnd@arndb.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
First, printk() is NMI-context safe now since the safe printk() has been
implemented and it already has an irq_work to make NMI-context safe.
Second, this NMI irq_work actually does not work if a NMI handler causes
panic by watchdog timeout. It has no chance to run in such case, while
the safe printk() will flush its per-cpu buffers before panicking.
While at it, repurpose the irq_work callback into a function which
concentrates the NMI duration checking and makes the code easier to
follow.
[ bp: Massage. ]
Signed-off-by: Changbin Du <changbin.du@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20200111125427.15662-1-changbin.du@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The rtl8188 copy of the os_dep support code causes a
warning about a very significant stack usage in the translate_scan()
function:
drivers/staging/rtl8188eu/os_dep/ioctl_linux.c: In function 'translate_scan':
drivers/staging/rtl8188eu/os_dep/ioctl_linux.c:306:1: error: the frame size of 1560 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Use the same trick as in the rtl8723bs copy of the same function, and
allocate it dynamically.
The AVerMedia CE310B is a simple composite + S-Video + stereo audio
capture card, and uses only the CX23888 to perform all of these
functions.
I've tested both video inputs and the audio interface and confirmed that
they're all working. However, there are some issues:
* Sometimes when I switch inputs the video signal turns black and can't
be recovered until the system is rebooted. I haven't been able to
determine the cause of this behavior, nor have I found a solution to
fix it or any workarounds other than rebooting.
* The card sometimes seems to have trouble syncing to the video signal,
and some of the VBI data appears as noise at the top of the frame, but
I assume that to be a result of my very noisy RF environment and the
card's unshielded input traces rather than a configuration issue.
Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.
This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.
Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.
[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c] Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In file included from ../arch/s390/purgatory/purgatory.c:10:
In file included from ../include/linux/kexec.h:18:
In file included from ../include/linux/crash_core.h:6:
In file included from ../include/linux/elfcore.h:5:
In file included from ../include/linux/user.h:1:
In file included from ../arch/s390/include/asm/user.h:11:
../arch/s390/include/asm/page.h:45:6: warning: converting the result of
'<<' to a boolean always evaluates to false
[-Wtautological-constant-compare]
if (PAGE_DEFAULT_KEY)
^
../arch/s390/include/asm/page.h:23:44: note: expanded from macro
'PAGE_DEFAULT_KEY'
#define PAGE_DEFAULT_KEY (PAGE_DEFAULT_ACC << 4)
^
1 warning generated.
Explicitly compare this against zero to silence the warning as it is
intended to be used in a boolean context.
xen_maybe_preempt_hcall() is called from the exception entry point
xen_do_hypervisor_callback with interrupts disabled.
_cond_resched() evades the might_sleep() check in cond_resched() which
would have caught that and schedule_debug() unfortunately lacks a check
for irqs_disabled().
Enable interrupts around the call and use cond_resched() to catch future
issues.
Fixes: fdfd811ddde3 ("x86/xen: allow privcmd hypercalls to be preempted") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/878skypjrh.fsf@nanos.tec.linutronix.de Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
device_shutdown() called from reboot or power_shutdown expect
all devices to be shutdown. Same is true for even ahci pci driver.
As no ahci shutdown function is implemented, the ata subsystem
always remains alive with DMA & interrupt support. File system
related calls should not be honored after device_shutdown().
So defining ahci pci driver shutdown to freeze hardware (mask
interrupt, stop DMA engine and free DMA resources).
The user-specified hashtable size is unbound, this could
easily lead to an OOM or a hung task as we hold the global
mutex while allocating and initializing the new hashtable.
Add a max value to cap both cfg->size and cfg->max, as
suggested by Florian.
Reported-and-tested-by: syzbot+adf6c6c2be1c3a718121@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
snd_seq_check_queue() passes the current tick and time of the given
queue as a pointer to snd_seq_prioq_cell_out(), but those might be
updated concurrently by the seq timer update.
Fix it by retrieving the current tick and time via the proper helper
functions at first, and pass those values to snd_seq_prioq_cell_out()
later in the loops.
snd_seq_timer_get_cur_time() takes a new argument and adjusts with the
current system time only when it's requested so; this update isn't
needed for snd_seq_check_queue(), as it's called either from the
interrupt handler or right after queuing.
Also, snd_seq_timer_get_cur_tick() is changed to read the value in the
spinlock for the concurrency, too.
The queue flags are represented in bit fields and the concurrent
access may result in unexpected results. Although the current code
should be mostly OK as it's only reading a field while writing other
fields as KCSAN reported, it's safer to cover both with a proper
spinlock protection.
This patch fixes the possible concurrent read by protecting with
q->owner_lock. Also the queue owner field is protected as well since
it's the field to be protected by the lock itself.
The rawmidi state flags (opened, append, active_sensing) are stored in
bit fields that can be potentially racy when concurrently accessed
without any locks. Although the current code should be fine, there is
also no any real benefit by keeping the bitfields for this kind of
short number of members.
This patch changes those bit fields flags to the simple bool fields.
There should be no size increase of the snd_rawmidi_substream by this
change.
Qian Cai reported that the WARN_ON() in the x86/msi affinity setting code,
which catches cases where the affinity setting is not done on the CPU which
is the current target of the interrupt, triggers during CPU hotplug stress
testing.
It turns out that the warning which was added with the commit addressing
the MSI affinity race unearthed yet another long standing bug.
If user space writes a bogus affinity mask, i.e. it contains no online CPUs,
then it calls irq_select_affinity_usr(). This was introduced for ALPHA in
eee45269b0f5 ("[PATCH] Alpha: convert to generic irq framework (generic part)")
and subsequently made available for all architectures in
which introduced the circumvention of the affinity setting restrictions for
interrupt which cannot be moved in process context.
The whole exercise is bogus in various aspects:
1) If the interrupt is already started up then there is absolutely
no point to honour a bogus interrupt affinity setting from user
space. The interrupt is already assigned to an online CPU and it
does not make any sense to reassign it to some other randomly
chosen online CPU.
2) If the interupt is not yet started up then there is no point
either. A subsequent startup of the interrupt will invoke
irq_setup_affinity() anyway which will chose a valid target CPU.
So the only correct solution is to just return -EINVAL in case user space
wrote an affinity mask which does not contain any online CPUs, except for
ALPHA which has it's own magic sauce for this.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Reported-by: Qian Cai <cai@lca.pw> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Qian Cai <cai@lca.pw> Link: https://lkml.kernel.org/r/878sl8xdbm.fsf@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The intel_svm_is_pasid_valid() needs to be marked inline, otherwise it
causes the compile warning below:
CC [M] drivers/dma/idxd/cdev.o
In file included from drivers/dma/idxd/cdev.c:9:0:
./include/linux/intel-svm.h:125:12: warning: ‘intel_svm_is_pasid_valid’ defined but not used [-Wunused-function]
static int intel_svm_is_pasid_valid(struct device *dev, int pasid)
^~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Borislav Petkov <bp@alien8.de> Fixes: 15060aba71711 ('iommu/vt-d: Helper function to query if a pasid has any active users') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In crypt_scatterlist, if the crypt_stat argument is not set up
correctly, the kernel crashes. Instead, by returning an error code
upstream, the error is handled safely.
The issue is detected via a static analysis tool written by us.
When we call kobject_put() and it's the last reference to the kobject
then it calls gb_audio_module_release() and frees module. We dereference
"module" on the next line which is a use after free.
Currently the rtw_sprintf prints the contents of thread_name
onto thread_name and this can lead to a potential copy of a
string over itself. Avoid this by printing the literal string RTWHALXT
instread of the contents of thread_name.
Addresses-Coverity: ("copy of overlapping memory") Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200126220549.9849-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SuperSpeedPlus peripherals must report their bMaxPower of the
configuration descriptor in units of 8mA as per the USB 3.2
specification. The current switch statement in encode_bMaxPower()
only checks for USB_SPEED_SUPER but not USB_SPEED_SUPER_PLUS so
the latter falls back to USB 2.0 encoding which uses 2mA units.
Replace the switch with a simple if/else.
Fixes: eae5820b852f ("usb: gadget: composite: Write SuperSpeedPlus config descriptors") Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>