Merge tag 'acpi-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPICA regression causing the AML parser to get confused
and fail in some situations involving incorrect AML in an ACPI table
(Erik Schmauss)"
* tag 'acpi-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: AML Parser: ignore dispatcher error status during table load
Merge tag 'pm-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix up the recently introduced cpufreq driver for Qualcomm Kryo
processors by adding a terminating NULL entry to its table of device
IDs (YueHaibing)"
* tag 'pm-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-kryo: add NULL entry to the end of_device_id array
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One more round of updates for problems seen this -rc series. Drivers
fixes are:
- Amlogic Meson audio divider fix and CPU clk critical marking
- Qualcomm multimedia GDSC marked as 'always on' to keep display
working
- Aspeed fixes for critical clks, resets causing clks to stay
disabled, and an incorrect HPLL frequency calculation
- Marvell Armada 3700 cpu clks would undervolt when switching from
low frequencies to high frequencies because the voltage didn't
stabilize in time so now we switch to an intermediate frequency
Plus we have a core framework thinko that messed up the debugfs flag
printing logic to make it not very useful"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: aspeed: Support HPLL strapping on ast2400
clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz
clk: aspeed: Mark bclk (PCIe) and dclk (VGA) as critical
clk/mmcc-msm8996: Make mmagic_bimc_gdsc ALWAYS_ON
clk: aspeed: Treat a gate in reset as disabled
clk: Really show symbolic clock flags in debugfs
clk: qcom: gcc-msm8996: Disable halt check on UFS tx clock
clk: meson: audio-divider is one based
clk: meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL
Merge tag 'fscache-fixes-20180725' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache/cachefiles fixes from David Howells:
- Allow cancelled operations to be queued so they can be cleaned up.
- Fix a refcounting bug in the monitoring of reads on backend files
whereby a race can occur between monitor objects being listed for
work, the work processing being queued and the work processor running
and destroying the monitor objects.
- Fix a ref overput in object attachment, whereby a tentatively
considered object is put in error handling without first being 'got'.
- Fix a missing clear of the CACHEFILES_OBJECT_ACTIVE flag whereby an
assertion occurs when we retry because it seems the object is now
active.
- Wait rather BUG'ing on an object collision in the depths of
cachefiles as the active object should be being cleaned up - also
depends on the one above.
* tag 'fscache-fixes-20180725' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
cachefiles: Wait rather than BUG'ing on "Unexpected object collision"
cachefiles: Fix missing clear of the CACHEFILES_OBJECT_ACTIVE flag
fscache: Fix reference overput in fscache_attach_object() error handling
cachefiles: Fix refcounting bug in backing-file read monitoring
fscache: Allow cancelled operations to be enqueued
cachefiles: Wait rather than BUG'ing on "Unexpected object collision"
If we meet a conflicting object that is marked FSCACHE_OBJECT_IS_LIVE in
the active object tree, we have been emitting a BUG after logging
information about it and the new object.
Instead, we should wait for the CACHEFILES_OBJECT_ACTIVE flag to be cleared
on the old object (or return an error). The ACTIVE flag should be cleared
after it has been removed from the active object tree. A timeout of 60s is
used in the wait, so we shouldn't be able to get stuck there.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
cachefiles: Fix missing clear of the CACHEFILES_OBJECT_ACTIVE flag
In cachefiles_mark_object_active(), the new object is marked active and
then we try to add it to the active object tree. If a conflicting object
is already present, we want to wait for that to go away. After the wait,
we go round again and try to re-mark the object as being active - but it's
already marked active from the first time we went through and a BUG is
issued.
Fix this by clearing the CACHEFILES_OBJECT_ACTIVE flag before we try again.
Analysis from Kiran Kumar Modukuri:
[Impact]
Oops during heavy NFS + FSCache + Cachefiles
CacheFiles: Error: Overlong wait for old active object to go away.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000002
CacheFiles: Error: Object already active kernel BUG at
fs/cachefiles/namei.c:163!
[Cause]
In a heavily loaded system with big files being read and truncated, an
fscache object for a cookie is being dropped and a new object being
looked. The new object being looked for has to wait for the old object
to go away before the new object is moved to active state.
[Fix]
Clear the flag 'CACHEFILES_OBJECT_ACTIVE' for the new object when
retrying the object lookup.
[Testcase]
Have run ~100 hours of NFS stress tests and have not seen this bug recur.
[Regression Potential]
- Limited to fscache/cachefiles.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
fscache: Fix reference overput in fscache_attach_object() error handling
When a cookie is allocated that causes fscache_object structs to be
allocated, those objects are initialised with the cookie pointer, but
aren't blessed with a ref on that cookie unless the attachment is
successfully completed in fscache_attach_object().
If attachment fails because the parent object was dying or there was a
collision, fscache_attach_object() returns without incrementing the cookie
counter - but upon failure of this function, the object is released which
then puts the cookie, whether or not a ref was taken on the cookie.
Fix this by taking a ref on the cookie when it is assigned in
fscache_object_init(), even when we're creating a root object.
Analysis from Kiran Kumar:
This bug has been seen in 4.4.0-124-generic #148-Ubuntu kernel
kernel BUG at /build/linux-Y09MKI/linux-4.4.0/fs/fscache/internal.h:321!
kernel BUG at /build/linux-Y09MKI/linux-4.4.0/fs/fscache/cookie.c:639!
[Cause]
Two threads are trying to do operate on a cookie and two objects.
(1) One thread tries to unmount the filesystem and in process goes over a
huge list of objects marking them dead and deleting the objects.
cookie->usage is also decremented in following path:
(2) A second thread tries to lookup an object for reading data in following
path:
fscache_alloc_object
1) cachefiles_alloc_object
-> fscache_object_init
-> assign cookie, but usage not bumped.
2) fscache_attach_object -> fails in cant_attach_object because the
cookie's backing object or cookie's->parent object are going away
3) fscache_put_object
-> cachefiles_put_object
->fscache_object_destroy
->fscache_cookie_put
->BUG_ON(atomic_read(&cookie->usage) <= 0);
[NOTE from dhowells] It's unclear as to the circumstances in which (2) can
take place, given that thread (1) is in nfs_kill_super(), however a
conflicting NFS mount with slightly different parameters that creates a
different superblock would do it. A backtrace from Kiran seems to show
that this is a possibility:
[Fix] Bump up the cookie usage in fscache_object_init, when it is first
being assigned a cookie atomically such that the cookie is added and bumped
up if its refcount is not zero. Remove the assignment in
fscache_attach_object().
[Testcase]
I have run ~100 hours of NFS stress tests and not seen this bug recur.
[Regression Potential]
- Limited to fscache/cachefiles.
Fixes: ccc4fc3d11e9 ("FS-Cache: Implement the cookie management part of the netfs API") Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
cachefiles: Fix refcounting bug in backing-file read monitoring
cachefiles_read_waiter() has the right to access a 'monitor' object by
virtue of being called under the waitqueue lock for one of the pages in its
purview. However, it has no ref on that monitor object or on the
associated operation.
What it is allowed to do is to move the monitor object to the operation's
to_do list, but once it drops the work_lock, it's actually no longer
permitted to access that object. However, it is trying to enqueue the
retrieval operation for processing - but it can only do this via a pointer
in the monitor object, something it shouldn't be doing.
If it doesn't enqueue the operation, the operation may not get processed.
If the order is flipped so that the enqueue is first, then it's possible
for the work processor to look at the to_do list before the monitor is
enqueued upon it.
Fix this by getting a ref on the operation so that we can trust that it
will still be there once we've added the monitor to the to_do list and
dropped the work_lock. The op can then be enqueued after the lock is
dropped.
The bug can manifest in one of a couple of ways. The first manifestation
looks like:
FS-Cache:
FS-Cache: Assertion failed
FS-Cache: 6 == 5 is false
------------[ cut here ]------------
kernel BUG at fs/fscache/operation.c:494!
RIP: 0010:fscache_put_operation+0x1e3/0x1f0
...
fscache_op_work_func+0x26/0x50
process_one_work+0x131/0x290
worker_thread+0x45/0x360
kthread+0xf8/0x130
? create_worker+0x190/0x190
? kthread_cancel_work_sync+0x10/0x10
ret_from_fork+0x1f/0x30
This is due to the operation being in the DEAD state (6) rather than
INITIALISED, COMPLETE or CANCELLED (5) because it's already passed through
fscache_put_operation().
fscache: Allow cancelled operations to be enqueued
Alter the state-check assertion in fscache_enqueue_operation() to allow
cancelled operations to be given processing time so they can be cleaned up.
Also fix a debugging statement that was requiring such operations to have
an object assigned.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") Reported-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
Merge tag 'mips_fixes_4.18_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes for 4.18:
- Fix an off-by-one in reporting PCI resource sizes to userland which
regressed in v3.12.
- Fix writes to DDR controller registers used to flush write buffers,
which regressed with some refactoring in v4.2"
* tag 'mips_fixes_4.18_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: ath79: fix register address in ath79_ddr_wb_flush()
MIPS: Fix off-by-one in pci_resource_to_user()
1) Handle stations tied to AP_VLANs properly during mac80211 hw
reconfig. From Manikanta Pubbisetty.
2) Fix jump stack depth validation in nf_tables, from Taehee Yoo.
3) Fix quota handling in aRFS flow expiration of mlx5 driver, from Eran
Ben Elisha.
4) Exit path handling fix in powerpc64 BPF JIT, from Daniel Borkmann.
5) Use ptr_ring_consume_bh() in page pool code, from Tariq Toukan.
6) Fix cached netdev name leak in nf_tables, from Florian Westphal.
7) Fix memory leaks on chain rename, also from Florian Westphal.
8) Several fixes to DCTCP congestion control ACK handling, from Yuchunk
Cheng.
9) Missing rcu_read_unlock() in CAIF protocol code, from Yue Haibing.
10) Fix link local address handling with VRF, from David Ahern.
11) Don't clobber 'err' on a successful call to __skb_linearize() in
skb_segment(). From Eric Dumazet.
12) Fix vxlan fdb notification races, from Roopa Prabhu.
13) Hash UDP fragments consistently, from Paolo Abeni.
14) If TCP receives lots of out of order tiny packets, we do really
silly stuff. Make the out-of-order queue ending more robust to this
kind of behavior, from Eric Dumazet.
15) Don't leak netlink dump state in nf_tables, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: axienet: Fix double deregister of mdio
qmi_wwan: fix interface number for DW5821e production firmware
ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull
bnx2x: Fix invalid memory access in rss hash config path.
net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper
r8169: restore previous behavior to accept BIOS WoL settings
cfg80211: never ignore user regulatory hint
sock: fix sg page frag coalescing in sk_alloc_sg
netfilter: nf_tables: move dumper state allocation into ->start
tcp: add tcp_ooo_try_coalesce() helper
tcp: call tcp_drop() from tcp_data_queue_ofo()
tcp: detect malicious patterns in tcp_collapse_ofo_queue()
tcp: avoid collapses in tcp_prune_queue() if possible
tcp: free batches of packets in tcp_prune_ofo_queue()
ip: hash fragments consistently
ipv6: use fib6_info_hold_safe() when necessary
can: xilinx_can: fix power management handling
can: xilinx_can: fix incorrect clear of non-processed interrupts
can: xilinx_can: fix RX overflow interrupt not being enabled
can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
...
qmi_wwan: fix interface number for DW5821e production firmware
The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).
Fixes: e7e197edd09c25 ("qmi_wwan: add support for the Dell Wireless 5821e module") Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
bnx2x: Fix invalid memory access in rss hash config path.
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 24 Jul 2018 11:27:55 +0000 (14:27 +0300)]
net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper
Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.
However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.
Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: restore previous behavior to accept BIOS WoL settings
Commit 7edf6d314cd0 tried to resolve an inconsistency (BIOS WoL
settings are accepted, but device isn't wakeup-enabled) resulting
from a previous broken-BIOS workaround by making disabled WoL the
default.
This however had some side effects, most likely due to a broken BIOS
some systems don't properly resume from suspend when the MagicPacket
WoL bit isn't set in the chip, see
https://bugzilla.kernel.org/show_bug.cgi?id=200195
Therefore restore the WoL behavior from 4.16.
Reported-by: Albert Astals Cid <aacid@kde.org> Fixes: 7edf6d314cd0 ("r8169: disable WOL per default") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fix from Martin Schwidefsky.
Guenter Roeck reports that the s390 allmodconfig build fails because of
a gcc plugin problem. The fix won't be in-tree until 4.19, so for now
disable the gcc plugins on s390.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: disable gcc plugins
media: staging: omap4iss: Include asm/cacheflush.h after generic includes
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Tue, 24 Jul 2018 16:38:50 +0000 (09:38 -0700)]
Merge tag 'mac80211-for-davem-2018-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Only a few fixes:
* always keep regulatory user hint
* add missing break statement in station flags parsing
* fix non-linear SKBs in port-control-over-nl80211
* reconfigure VLAN stations during HW restart
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cpufreq: qcom-kryo: add NULL entry to the end of_device_id array
Make sure of_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Ilia Lin <ilia.lin@kernel.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently user regulatory hint is ignored if all wiphys
in the system are self managed. But the hint is not ignored
if there is no wiphy in the system. This affects the global
regulatory setting. Global regulatory setting needs to be
maintained so that it can be applied to a new wiphy entering
the system. Therefore, do not ignore user regulatory setting
even if all wiphys in the system are self managed.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Daniel Borkmann [Mon, 23 Jul 2018 20:37:54 +0000 (22:37 +0200)]
sock: fix sg page frag coalescing in sk_alloc_sg
Current sg coalescing logic in sk_alloc_sg() (latter is used by tls and
sockmap) is not quite correct in that we do fetch the previous sg entry,
however the subsequent check whether the refilled page frag from the
socket is still the same as from the last entry with prior offset and
length matching the start of the current buffer is comparing always the
first sg list entry instead of the prior one.
Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: move dumper state allocation into ->start
Shaochun Chen points out we leak dumper filter state allocations
stored in dump_control->data in case there is an error before netlink sets
cb_running (after which ->done will be called at some point).
In order to fix this, add .start functions and do the allocations
there.
->done is going to clean up, and in case error occurs before
->start invocation no cleanups need to be done anymore.
Reported-by: shaochun chen <cscnull@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Mon, 23 Jul 2018 19:01:36 +0000 (12:01 -0700)]
Merge branch 'tcp-robust-ooo'
Eric Dumazet says:
====================
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet.
With tcp_rmem[2] default of 6MB, the ooo queue could
contain ~7000 nodes.
This patch series makes sure we cut cpu cycles enough to
render the attack not critical.
We might in the future go further, like disconnecting
or black-holing proven malicious flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Jul 2018 16:28:21 +0000 (09:28 -0700)]
tcp: add tcp_ooo_try_coalesce() helper
In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.
I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Jul 2018 16:28:20 +0000 (09:28 -0700)]
tcp: call tcp_drop() from tcp_data_queue_ofo()
In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.
Fixes: 9f5afeae5152 ("tcp: use an RB tree for ooo receive queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Jul 2018 16:28:19 +0000 (09:28 -0700)]
tcp: detect malicious patterns in tcp_collapse_ofo_queue()
In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.
1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.
We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.
In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Jul 2018 16:28:18 +0000 (09:28 -0700)]
tcp: avoid collapses in tcp_prune_queue() if possible
Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :
if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
tcp_clamp_window(sk);
tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])
Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.
Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Jul 2018 16:28:17 +0000 (09:28 -0700)]
tcp: free batches of packets in tcp_prune_ofo_queue()
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.
Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.
Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.
Strategy taken in this patch is to purge ~12.5 % of the queue capacity.
Fixes: 36a6503fedda ("tcp: refine tcp_prune_ofo_queue() to not drop all packets") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 23 Jul 2018 14:50:48 +0000 (16:50 +0200)]
ip: hash fragments consistently
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
Fixes: b73c3d0e4f0e ("net: Save TX flow hash in sock and set in skbuf on xmit") Fixes: 67800f9b1f4e ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sun, 22 Jul 2018 03:56:32 +0000 (20:56 -0700)]
ipv6: use fib6_info_hold_safe() when necessary
In the code path where only rcu read lock is held, e.g. in the route
lookup code path, it is not safe to directly call fib6_info_hold()
because the fib6_info may already have been deleted but still exists
in the rcu grace period. Holding reference to it could cause double
free and crash the kernel.
This patch adds a new function fib6_info_hold_safe() and replace
fib6_info_hold() in all necessary places.
Syzbot reported 3 crash traces because of this. One of them is:
8021q: adding VLAN 0 to HW filter on device team0
IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
dst_release: dst:(____ptrval____) refcnt:-1
dst_release: dst:(____ptrval____) refcnt:-2
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 dst_hold include/net/dst.h:239 [inline]
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204
dst_release: dst:(____ptrval____) refcnt:-1
Kernel panic - not syncing: panic_on_warn set ...
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: syzbot+902e2a1bcd4f7808cef5@syzkaller.appspotmail.com Reported-by: syzbot+8ae62d67f647abeeceb9@syzkaller.appspotmail.com Reported-by: syzbot+3f08feb14086930677d0@syzkaller.appspotmail.com Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Jul 2018 18:02:21 +0000 (11:02 -0700)]
Merge tag 'linux-can-fixes-for-4.18-20180723' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-07-23
this is a pull request of 12 patches for net/master.
The patch by Stephane Grosjean for the peak_canfd CAN driver fixes a problem
with older firmware. The next patch is by Roman Fietze and fixes the setup of
the CCCR register in the m_can driver. Nicholas Mc Guire's patch for the
mpc5xxx_can driver adds missing error checking. The two patches by Faiz Abbas
fix the runtime resume and clean up the probe function in the m_can driver. The
last 7 patches by Anssi Hannula fix several problem in the xilinx_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula [Thu, 17 May 2018 12:41:19 +0000 (15:41 +0300)]
can: xilinx_can: fix power management handling
There are several issues with the suspend/resume handling code of the
driver:
- The device is attached and detached in the runtime_suspend() and
runtime_resume() callbacks if the interface is running. However,
during xcan_chip_start() the interface is considered running,
causing the resume handler to incorrectly call netif_start_queue()
at the beginning of xcan_chip_start(), and on xcan_chip_start() error
return the suspend handler detaches the device leaving the user
unable to bring-up the device anymore.
- The device is not brought properly up on system resume. A reset is
done and the code tries to determine the bus state after that.
However, after reset the device is always in Configuration mode
(down), so the state checking code does not make sense and
communication will also not work.
- The suspend callback tries to set the device to sleep mode (low-power
mode which monitors the bus and brings the device back to normal mode
on activity), but then immediately disables the clocks (possibly
before the device reaches the sleep mode), which does not make sense
to me. If a clean shutdown is wanted before disabling clocks, we can
just bring it down completely instead of only sleep mode.
Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.
The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.
xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.
Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.
Tested on Zynq-7000 integrated CAN.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Mon, 26 Feb 2018 12:39:59 +0000 (14:39 +0200)]
can: xilinx_can: fix incorrect clear of non-processed interrupts
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.
Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Mon, 26 Feb 2018 12:27:13 +0000 (14:27 +0200)]
can: xilinx_can: fix RX overflow interrupt not being enabled
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).
Fix that by enabling the RXOFLW interrupt.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Thu, 23 Feb 2017 12:50:03 +0000 (14:50 +0200)]
can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Wed, 8 Feb 2017 11:13:40 +0000 (13:13 +0200)]
can: xilinx_can: fix recovery from error states not being propagated
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.
Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Tue, 7 Feb 2017 15:01:14 +0000 (17:01 +0200)]
can: xilinx_can: fix RX loop if RXNEMP is asserted without RXOK
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Tue, 7 Feb 2017 11:23:04 +0000 (13:23 +0200)]
can: xilinx_can: fix device dropping off bus on RX overrun
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
Remove the software reset.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: mpc5xxx_can: check of_iomap return before use
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roman Fietze [Wed, 11 Jul 2018 13:36:14 +0000 (15:36 +0200)]
can: m_can.c: fix setup of CCCR register: clear CCCR NISO bit before checking can.ctrlmode
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.
This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.
This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: peak_canfd: fix firmware < v3.3.0: limit allocation to 32-bit DMA addr only
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
Schmauss, Erik [Thu, 19 Jul 2018 23:33:00 +0000 (16:33 -0700)]
ACPICA: AML Parser: ignore dispatcher error status during table load
The dispatcher and the executer process the parse nodes During table
load. Error status from the evaluation confuses the AML parser. This
results in the parser failing to complete parsing of the current
scope op which becomes problematic. For the incorrect AML below, _ADR
never gets created.
definition_block(...)
{
Scope (\_SB)
{
Device (PCI0){...}
Name (OBJ1, 0x0)
OBJ1 = PCI0 + 5 // Results in an operand error.
} // \_SB not closed
// parser looks for \_SB._SB.PCI0, results in AE_NOT_FOUND error
// Entire scope block gets skipped.
Scope (\_SB.PCI0)
{
Name (_ADR, 0x0)
}
}
Fix the above error by properly completing the initial \_SB scope
after an error by clearing errors that occur during table load. In
the above case, this means that OBJ1 = PIC0 + 5 is skipped.
Fixes: 5088814a6e93 (ACPICA: AML parser: attempt to continue loading table after error) Link: https://bugzilla.kernel.org/show_bug.cgi?id=200363 Tested-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Erik Schmauss <erik.schmauss@intel.com> Cc: 4.17+ <stable@vger.kernel.org> # 4.17+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'nvme-for-4.18' of git://git.infradead.org/nvme
Pull NVMe fixes from Christoph Hellwig:
- fix a regression in 4.18 that causes a memory leak on probe failure
(Keith Bush)
- fix a deadlock in the passthrough ioctl code (Scott Bauer)
- don't enable AENs if not supported (Weiping Zhang)
- fix an old regression in metadata handling in the passthrough ioctl
code (Roland Dreier)
* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
nvme: don't enable AEN if not supported
nvme: ensure forward progress during Admin passthru
nvme-pci: fix memory leak on probe failure
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Fix several places that screw up cleanups after failures halfway
through opening a file (one open-coding filp_clone_open() and getting
it wrong, two misusing alloc_file()). That part is -stable fodder from
the 'work.open' branch.
And Christoph's regression fix for uapi breakage in aio series;
include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
definition of sigset_t, the reason for doing so in the first place had
been bogus - there's no need to expose struct __aio_sigset in
aio_abi.h at all"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: don't expose __aio_sigset in uapi
ocxlflash_getfile(): fix double-iput() on alloc_file() failures
cxl_getfile(): fix double-iput() on alloc_file() failures
drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()
Randy Dunlap [Sat, 21 Jul 2018 19:59:25 +0000 (12:59 -0700)]
net: prevent ISA drivers from building on PPC32
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Sat, 21 Jul 2018 04:07:54 +0000 (21:07 -0700)]
nfp: flower: ensure dead neighbour entries are not offloaded
Previously only the neighbour state was checked to decide if an offloaded
entry should be removed. However, there can be situations when the entry
is dead but still marked as valid. This can lead to dead entries not
being removed from fw tables or even incorrect data being added.
Check the entry dead bit before deciding if it should be added to or
removed from fw neighbour tables.
Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This series fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- modify rtnl_configure_link to allow configuring a link early.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
====================
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink: add rtnl_link_state check in rtnl_configure_link
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 20 Jul 2018 06:04:27 +0000 (14:04 +0800)]
multicast: do not restore deleted record source filter mode to new one
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
Fixes: 24803f38a5c0b (igmp: do not remove igmp souce list info when set link down) Fixes: 1666d49e1d416 (mld: do not remove mld souce list info when set link down) Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: mv88e6xxx: fix races between lock and irq freeing
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ddff00d42043 ("net: Move skb_has_shared_frag check out of GRE code and into segmentation") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 19 Jul 2018 19:41:18 +0000 (12:41 -0700)]
net/ipv6: Fix linklocal to global address with VRF
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff74384600a ("net: vrf: Handle ipv6 multicast and link-local addresses") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"This is mostly the copy_to_user_mcsafe() related fixes from Dan
Williams, and an ORC fix for Clang"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/memcpy_mcsafe: Fix copy_to_user_mcsafe() exception handling
lib/iov_iter: Fix pipe handling in _copy_to_iter_mcsafe()
lib/iov_iter: Document _copy_to_iter_flushcache()
lib/iov_iter: Document _copy_to_iter_mcsafe()
objtool: Use '.strtab' if '.shstrtab' doesn't exist, to support ORC tables on Clang
Merge tag 'powerpc-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two regression fixes, one for xmon disassembly formatting and the
other to fix the E500 build.
Two commits to fix a potential security issue in the VFIO code under
obscure circumstances.
And finally a fix to the Power9 idle code to restore SPRG3, which is
user visible and used for sched_getcpu().
Thanks to: Alexey Kardashevskiy, David Gibson. Gautham R. Shenoy,
James Clarke"
* tag 'powerpc-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from stop (idle)
powerpc/Makefile: Assemble with -me500 when building for E500
KVM: PPC: Check if IOMMU page is contained in the pinned physical page
vfio/spapr: Use IOMMU pageshift rather than pagesize
powerpc/xmon: Fix disassembly since printf changes
Fix following warning:
net/ipv4/bpfilter/sockopt.c:28:5: error: symbol 'bpfilter_ip_set_sockopt' redeclared with different type
net/ipv4/bpfilter/sockopt.c:34:5: error: symbol 'bpfilter_ip_get_sockopt' redeclared with different type
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: consider PHY_IGNORE_INTERRUPT in phy_start_aneg_priv
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable interrupt") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Fix link flap issue due to mismatching EEE capabilities.
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: caif: Add a missing rcu_read_unlock() in caif_flow_cb
Add a missing rcu_read_unlock in the error path
Fixes: c95567c80352 ("caif: added check for potential null return") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mm: use helper functions for allocating and freeing vm_area structs
The vm_area_struct is one of the most fundamental memory management
objects, but the management of it is entirely open-coded evertwhere,
ranging from allocation and freeing (using kmem_cache_[z]alloc and
kmem_cache_free) to initializing all the fields.
We want to unify this in order to end up having some unified
initialization of the vmas, and the first step to this is to at least
have basic allocation functions.
Right now those functions are literally just wrappers around the
kmem_cache_*() calls. This is a purely mechanical conversion:
# new vma:
kmem_cache_zalloc(vm_area_cachep, GFP_KERNEL) -> vm_area_alloc()
# copy old vma
kmem_cache_alloc(vm_area_cachep, GFP_KERNEL) -> vm_area_dup(old)
to the point where the old vma passed in to the vm_area_dup() function
isn't even used yet (because I've left all the old manual initialization
alone).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: fix use after free in mem_cgroup_iter()
mm/huge_memory.c: fix data loss when splitting a file pmd
fat: fix memory allocation failure handling of match_strdup()
MAINTAINERS: Peter has moved
mm/memblock: add missing include <linux/bootmem.h>
mm: memcg: fix use after free in mem_cgroup_iter()
It was reported that a kernel crash happened in mem_cgroup_iter(), which
can be triggered if the legacy cgroup-v1 non-hierarchical mode is used.
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f
......
Call trace:
mem_cgroup_iter+0x2e0/0x6d4
shrink_zone+0x8c/0x324
balance_pgdat+0x450/0x640
kswapd+0x130/0x4b8
kthread+0xe8/0xfc
ret_from_fork+0x10/0x20
mem_cgroup_iter():
......
if (css_tryget(css)) <-- crash here
break;
......
The crashing reason is that mem_cgroup_iter() uses the memcg object whose
pointer is stored in iter->position, which has been freed before and
filled with POISON_FREE(0x6b).
And the root cause of the use-after-free issue is that
invalidate_reclaim_iterators() fails to reset the value of iter->position
to NULL when the css of the memcg is released in non- hierarchical mode.
Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com Fixes: 6df38689e0e9 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim") Signed-off-by: Jing Xia <jing.xia.mail@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <chunyan.zhang@unisoc.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/huge_memory.c: fix data loss when splitting a file pmd
__split_huge_pmd_locked() must check if the cleared huge pmd was dirty,
and propagate that to PageDirty: otherwise, data may be lost when a huge
tmpfs page is modified then split then reclaimed.
How has this taken so long to be noticed? Because there was no problem
when the huge page is written by a write system call (shmem_write_end()
calls set_page_dirty()), nor when the page is allocated for a write fault
(fault_dirty_shared_page() calls set_page_dirty()); but when allocated for
a read fault (which MAP_POPULATE simulates), no set_page_dirty().
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1807111741430.1106@eggly.anvils Fixes: d21b9e57c74c ("thp: handle file pages in split_huge_pmd()") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Ashwin Chaugule <ashwinch@google.com> Reviewed-by: Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fat: fix memory allocation failure handling of match_strdup()
In parse_options(), if match_strdup() failed, parse_options() leaves
opts->iocharset in unexpected state (i.e. still pointing the freed
string). And this can be the cause of double free.
To fix, this initialize opts->iocharset always when freeing.
and commit ea1f5f3712af ("mm: define memblock_virt_alloc_try_nid_raw")
introduced the following function definition:
memblock_virt_alloc_try_nid_raw()
This commit adds an include of header file <linux/bootmem.h> to provide
the missing function prototypes. This silences the following gcc warning
(W=1):
mm/memblock.c:1334:15: warning: no previous prototype for `memblock_virt_alloc_try_nid_raw' [-Wmissing-prototypes]
mm/memblock.c:1371:15: warning: no previous prototype for `memblock_virt_alloc_try_nid_nopanic' [-Wmissing-prototypes]
mm/memblock.c:1407:15: warning: no previous prototype for `memblock_virt_alloc_try_nid' [-Wmissing-prototypes]
Also adds #ifdef blockers to prevent compilation failure on mips/ia64
where CONFIG_NO_BOOTMEM=n as could be seen in commit commit 6cc22dc08a24
("revert "mm/memblock: add missing include <linux/bootmem.h>"").
Jarod Wilson [Wed, 18 Jul 2018 18:49:36 +0000 (14:49 -0400)]
bonding: set default miimon value for non-arp modes if not set
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda0744, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu> Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following series provides fixes to mlx5 core and net device driver.
Please pull and let me know if there's any problem.
For -stable v4.7
net/mlx5e: Don't allow aRFS for encapsulated packets
net/mlx5e: Fix quota counting in aRFS expire flow
For -stable v4.15
net/mlx5e: Only allow offloading decap egress (egdev) flows
net/mlx5e: Refine ets validation function
net/mlx5: Adjust clock overflow work period
For -stable v4.17
net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix in BPF Makefile to detect llvm-objcopy in a more robust way which is
needed for pahole's BTF converter and minor UAPI tweaks in BTF_INT_BITS()
to shrink the mask before eventual UAPI freeze, from Martin.
2) Fix a segfault in bpftool when prog pin id has no further arguments such
as id value or file specified, from Taeung.
3) Fix powerpc JIT handling of XADD which has jumps to exit path that would
potentially bypass verifier expectations e.g. with subprog calls. Also add
a test case to make sure XADD is not mangling src/dst register, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not check sk->sk_shutdown & RCV_SHUTDOWN.
tls_sw_recvmsg may return a positive value in the case where bytes have
already been copied when the socket is shutdown. sk->sk_err has been
cleared, causing the tls_wait_data to hang forever on a subsequent
invocation. Checking sk->sk_shutdown & RCV_SHUTDOWN, as in tcp_recvmsg,
fixes this problem.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Acked-by: Dave Watson <davejwatson@fb.com> Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jul 2018 21:32:24 +0000 (14:32 -0700)]
Merge branch 'tcp-fix-DCTCP-ECE-Ack-series'
Yuchung Cheng says:
====================
fix DCTCP ECE Ack series
This patch set address that the existing DCTCP implementation does not
fully implement the ACK policy specified in the RFC. This improves
the responsiveness of CE status change particularly on flows with
small inflight.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001
+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and create helpers to send the special ACK in DCTCP.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'for-4.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM writecache target to allow an optional offset to the start of
the data and metadata area.
This allows userspace tools (e.g. LVM2) to place a header and metadata
at the front of the writecache device for its use"
* tag 'for-4.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm writecache: support optional offset for start of device
Olof Johansson [Fri, 20 Jul 2018 21:22:11 +0000 (14:22 -0700)]
Merge tag 'imx-fixes-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 4:
- A fix for i.MX6 RDU2 board on the wrong IRQ type of Marvell switch,
which might result in a race condition in the interrupt handler and
cause the OS to miss all future events.
* tag 'imx-fixes-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 8 obvious fixes.
Three (2 qla2xxx and the cxlflash oopses) are regressions, two from
4.17 and one from the merge window. The hpsa change is user visible,
but it fixes an error users have complained about"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: fix assignment of the backend operations
scsi: qedi: Send driver state to MFW
scsi: qedf: Send the driver state to MFW
scsi: hpsa: correct enclosure sas address
scsi: sd_zbc: Fix variable type and bogus comment
scsi: qla2xxx: Fix NULL pointer dereference for fcport search
scsi: qla2xxx: Fix kernel crash due to late workqueue allocation
scsi: qla2xxx: Fix inconsistent DMA mem alloc/free
Merge tag 'iommu-fixes-v4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Only one revert, for an an Intel VT-d patch that caused issues with
the i915 GPU driver"
* tag 'iommu-fixes-v4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/vt-d: Clean up pasid quirk for pre-production devices"
projects / mirror_ubuntu-kernels.git / log