usb: typec: tps6598x: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Mon, 30 Oct 2017 16:29:56 +0000 (11:29 -0500)]
usb: musb: dsps: remove the duplicated timer
Now struct musb has the timer (dev_timer) for glue drivers, so let's
remove the duplicated timer defined in dsps glue driver, and use
dev_timer defined in struct musb.
Signed-off-by: Bin Liu <b-liu@ti.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Tue, 24 Oct 2017 10:08:35 +0000 (03:08 -0700)]
usb: musb: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.
Cc: linux-usb@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397608 Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexandre Bailon [Fri, 27 Oct 2017 16:51:58 +0000 (11:51 -0500)]
usb: musb: da8xx: Remove duplicated defines
There is some registers defined in da8xx.c though they are not used.
These registers are also defined and used in musb_cppi41.c
Remove these defines from da8xx.c.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'extcon-next-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
Merge tag 'phy-for-4.15_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.15
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Merge tag 'usb-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.15 merge window
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
John Stultz [Mon, 23 Oct 2017 21:32:50 +0000 (14:32 -0700)]
usb: dwc2: Fix UDC state tracking
It has been noticed that the dwc2 udc state reporting doesn't
seem to work (at least on HiKey boards). Where after the initial
setup, the sysfs /sys/class/udc/f72c0000.usb/state file would
report "configured" no matter the state of the OTG port.
This patch adds a call so that we report to the UDC layer when
the gadget device is disconnected.
This patch does depend on the previous patch ("usb: dwc2:
Improve gadget state disconnection handling") in this patch set
in order to properly work.
Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: YongQin Liu <yongqin.liu@linaro.org> Cc: John Youn <johnyoun@synopsys.com> Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Chen Yu <chenyu56@huawei.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Acked-by: Minas Harutyunyan <hminas@synopsys.com> Tested-by: Minas Harutyunyan <hminas@synopsys.com> Reported-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Then when dwc2_hsotg_ep_disable() is called, we call
kill_all_requests() which causes a bunch of the following
messages:
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
init: Service 'adbd' (pid 1915) killed by signal 9
init: Sending signal 9 to service 'adbd' (pid 1915) process group...
init: Successfully killed process cgroup uid 0 pid 1915 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:15)
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 8 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 12 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 15 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 3 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_update_urb_state_abn(): trimming xfer length
And the usb devices connected are basically hung at this point.
It seems like if we're in host mode, we probably shouldn't run
the dwc2_hostg_ep_disable logic, so this patch returns an error
in that case.
With this patch (along with the previous patch in this set), we avoid
the mismatched interrupts and connected usb devices continue to function.
I'm not sure if some other solution would be better here, but this seems
to work, so I wanted to send it out for input on what the right approach
should be.
Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: YongQin Liu <yongqin.liu@linaro.org> Cc: John Youn <johnyoun@synopsys.com> Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Chen Yu <chenyu56@huawei.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Acked-by: Minas Harutyunyan <hminas@synopsys.com> Tested-by: Minas Harutyunyan <hminas@synopsys.com> Reported-by: YongQin Liu <yongqin.liu@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
John Stultz [Mon, 23 Oct 2017 21:32:48 +0000 (14:32 -0700)]
usb: dwc2: Improve gadget state disconnection handling
In the earlier commit dad3f793f20f ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.
(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)
The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.
But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.
Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.
Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: YongQin Liu <yongqin.liu@linaro.org> Cc: John Youn <johnyoun@synopsys.com> Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Chen Yu <chenyu56@huawei.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Acked-by: Minas Harutyunyan <hminas@synopsys.com> Tested-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Manu Gautam [Wed, 27 Sep 2017 11:19:22 +0000 (16:49 +0530)]
usb: dwc3: core: Notify current USB mode to USB3 PHY as well
Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Manu Gautam [Wed, 27 Sep 2017 11:19:21 +0000 (16:49 +0530)]
usb: dwc3: pci: Runtime resume child device from wq
Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Manu Gautam [Wed, 27 Sep 2017 11:19:20 +0000 (16:49 +0530)]
usb: dwc3: Don't reinitialize core during host bus-suspend/resume
Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Marek Szyprowski [Wed, 18 Oct 2017 09:56:22 +0000 (11:56 +0200)]
extcon: max77843: Add support for SmartDock accessory
SmartDock uses ADC_RESERVED_ACC_3 (0x10) ADC ID type and provides following
features:
1. USB host with embedded USB hub (2-4 ports) for mice, keyboard, etc,
2. MHL for video output,
3. charging.
Tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Marek Szyprowski [Wed, 18 Oct 2017 09:56:21 +0000 (11:56 +0200)]
extcon: max77843: Add OTG power control to the MUIC driver
Enabling power on VBUS micro-usb pin is required only when passive OTG
cable is connected. Initially OTG VBUS power control was planned to be
done in charger driver. However such information is not really available
from the extcon notifications, so VBUS power control has to be done
directly in MUIC driver, which has all information about the attached
accessory.
For example SmartDock is externally powered accessory, provides OTG
(USB HOST) functionality and use VBUS pin for charging a device battery,
so the VBUS charging pump should be disabled in such case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Linus Torvalds [Mon, 23 Oct 2017 10:37:16 +0000 (06:37 -0400)]
Merge tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here are a small number of patches to resolve some reported IIO and a
staging driver problem. Nothing major here, full details are in the
shortlog below.
All have been in linux-next with no reported issues"
* tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: bcm2835-audio: Fix memory corruption
iio: adc: at91-sama5d2_adc: fix probe error on missing trigger property
iio: adc: dln2-adc: fix build error
iio: dummy: events: Add missing break
staging: iio: ade7759: fix signed extension bug on shift of a u8
iio: pressure: zpa2326: Remove always-true check which confuses gcc
iio: proximity: as3935: noise detection + threshold changes
Linus Torvalds [Mon, 23 Oct 2017 10:35:01 +0000 (06:35 -0400)]
Merge tag 'char-misc-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are four small fixes for 4.14-rc6.
Three of them are binder driver fixes for reported issues, and the
last one is a hyperv driver bugfix. Nothing major, but good fixes to
get into 4.14-final.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
android: binder: Fix null ptr dereference in debug msg
android: binder: Don't get mm from task
vmbus: hvsock: add proper sync for vmbus_hvsock_device_unregister()
binder: call poll_wait() unconditionally.
Linus Torvalds [Mon, 23 Oct 2017 10:33:05 +0000 (06:33 -0400)]
Merge tag 'usb-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a small number of USB and PHY driver fixes for 4.14-rc6
There is the usual musb and xhci fixes in here, as well as some needed
phy patches. Also is a nasty regression fix for usbfs that has started
to hit a lot of people using virtual machines.
All of these have been in linux-next with no reported problems"
* tag 'usb-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: hub: Allow reset retry for USB2 devices on connect bounce
USB: core: fix out-of-bounds access bug in usb_get_bos_descriptor()
MAINTAINERS: fix git tree url for musb module
usb: quirks: add quirk for WORLDE MINI MIDI keyboard
usb: musb: sunxi: Explicitly release USB PHY on exit
usb: musb: Check for host-mode using is_host_active() on reset interrupt
usb: musb: musb_cppi41: Configure the number of channels for DA8xx
usb: musb: musb_cppi41: Fix cppi41_set_dma_mode() for DA8xx
usb: musb: musb_cppi41: Fix the address of teardown and autoreq registers
USB: musb: fix late external abort on suspend
USB: musb: fix session-bit runtime-PM quirk
usb: cdc_acm: Add quirk for Elatec TWN3
USB: devio: Revert "USB: devio: Don't corrupt user memory"
usb: xhci: Handle error condition in xhci_stop_device()
usb: xhci: Reset halted endpoint if trb is noop
xhci: Cleanup current_cmd in xhci_cleanup_command_queue()
xhci: Identify USB 3.1 capable hosts by their port protocol capability
USB: serial: metro-usb: add MS7820 device id
phy: rockchip-typec: Check for errors from tcphy_phy_init()
phy: rockchip-typec: Don't set the aux voltage swing to 400 mV
...
Daniel Drake [Wed, 18 Oct 2017 07:15:01 +0000 (15:15 +0800)]
USB: Force disconnect Huawei 4G modem during suspend
When going into S3 suspend, the Acer TravelMate P648-M and P648-G3
laptops immediately wake up 3-4 seconds later for no obvious reason.
Unbinding the integrated Huawei 4G LTE modem before suspend avoids
the issue, even though we are not using the modem at all (checked
from rescue.target/runlevel1). The problem also occurs when the option
and cdc-ether modem drivers aren't loaded; it reproduces just with the
base usb driver. Under Windows the system can suspend fine.
Seeking a better fix, we've tried a lot of things, including:
- Check that the device's power/wakeup is disabled
- Check that remote wakeup is off at the USB level
- All the quirks in drivers/usb/core/quirks.c e.g. USB_QUIRK_RESET_RESUME,
USB_QUIRK_RESET, USB_QUIRK_IGNORE_REMOTE_WAKEUP, USB_QUIRK_NO_LPM.
but none of that makes any difference.
There are no errors in the logs showing any suspend/resume-related issues.
When the system wakes up due to the modem, log-wise it appears to be a
normal resume.
Introduce a quirk to disable the port during suspend when the modem is
detected.
Jaejoong Kim [Fri, 20 Oct 2017 07:29:15 +0000 (16:29 +0900)]
usb: misc: usbtest: remove duplicate & operation
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun [Fri, 13 Oct 2017 08:26:36 +0000 (16:26 +0800)]
usb: xhci-mtk: support option to disable usb3 ports
Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Sometimes it's helpful to analyse and solve problems.
Chunfeng Yun [Fri, 13 Oct 2017 08:26:35 +0000 (16:26 +0800)]
usb: xhci-mtk: check clock stability of U3_MAC
This is useful to find out the root cause when the Super Speed doesn't
work. Such as when the T-PHY is switched to PCIe or SATA, and affects
Super Speed function, the check will fail.
Some quirky UDCs (like dwc3 on Exynos) need to have their phys calibrated e.g.
for using super speed. This patch adds a new phy_calibrate() method.
When the calibration should be used is dependent on actual chip.
In case of dwc3 on Exynos the calibration must happen after usb_add_hcd()
(while in host mode), because certain phy parameters like Tx LOS levels
and boost levels need to be calibrated further post initialization of xHCI
controller, to get SuperSpeed operations working. But an hcd must be
prepared first in order to pass it to usb_add_hcd(), so, in particular, dwc3
registers must be available first, and in order for the latter to happen
the phys must be initialized. This poses a chicken and egg problem if
the calibration were to be performed in phy_init(). To break the circular
dependency a separate method is added which can be called at a desired
moment after phy intialization.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Vivek Gautam [Thu, 12 Oct 2017 06:19:35 +0000 (11:49 +0530)]
scsi/ufs: qcom: Set phy mode based on the controllers HS MODE
Set the phy mode based on the UFS HS PA mode. This lets the
controller let phy know the mode in which the PHY Adapter is
running and set the phy rates accordingly.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Vivek Gautam [Thu, 12 Oct 2017 06:19:33 +0000 (11:49 +0530)]
phy: Add UFS PHY modes
UFS phy has two modes for each High speed generation.
These modes are identified by two rates of operations -
Rate A, and Rate B.
Add these UFS phy modes to phy framework.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update the PCIe phy settings based on new settings available
in AM572x Technical Reference Manual[1] Revision I, revised
April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register
Settings".
Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[nsekhar@ti.com: commit message updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PCI: dra7xx: Create functional dependency between PCIe and PHY
PCI core access configuration space registers in resume_noirq callbacks.
In the case of dra7xx, PIPE3 PHY connected to PCIe controller has to be
enabled before accessing configuration space registers. Since
PIPE3 PHY is enabled by only configuring control module registers, no
aborts has been observed so far (though during noirq stage, interface
clock of PIPE3 PHY is not enabled).
With new TRM updates, PIPE3 PHY has to be initialized (PIPE3 PHY
registers has to be accessed) as well which requires the interface
clock of PIPE3 PHY to be enabled. The interface clock of PIPE3 PHY is
derived from OCP2SCP and hence PCIe PHY is modeled as a child of
OCP2SCP. Since pm_runtime is not enabled during noirq stage,
pm_runtime_get_sync done in phy_init doesn't enable
OCP2SCP clocks resulting in abort when PIPE3 PHY registers are
accessed.
Create a function dependency between PCIe and PHY here to make
sure PCIe is suspended before PCIe PHY/OCP2SCP and resumed after
PCIe PHY/OCP2SCP.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Florian Fainelli [Thu, 12 Oct 2017 00:53:12 +0000 (17:53 -0700)]
phy: brcm-sata: Allow RX equalizer tuning
Parse the DT properties brcm,rxaeq-mode and brcm,rxaeq-value to
correctly configure the RX equalizer of the PHY. This may be required to
resolve specific signal integrity issues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Florian Fainelli [Thu, 12 Oct 2017 00:53:11 +0000 (17:53 -0700)]
phy: brcm-sata: Prepare for doing more tuning
Split the functional code in brcm_stb_sata_init() to a separate function
that actually does configure spread spectrum: brcm_stb_sata_ssc_init()
and make that function return void, since that function cannot fail.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Florian Fainelli [Thu, 12 Oct 2017 00:53:10 +0000 (17:53 -0700)]
dt-bindings: phy: Add RX equalizer properties for Broadcom SATA PHY
Define two new properties: brcm,rx-aeq-mode which allows configuring the
SATA PHY RX equalizers and when "manual" is used, brcm,rx-aeq can be
used to set the exact value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds binding for r8a77995 (R-Car D3). Since r8a77995 doesn't
have dedicated pins (ID, VBUS), this will match against the generic
fallback on R-Car D3.
For now, this driver doesn't support usb role swap for r8a77995.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: rcar-gen3-usb2: add SoC-specific parameter for dedicated pins
This patch adds SoC-specific parameter to avoid reading/writing
specific registers wrongly if this driver runs on a SoC which doesn't
have dedicated pins (e.g. R-Car D3). This patch also changes the
value "has_otg" to "has_otg_pins" for slightly easier reading of
the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: rcar-gen3-usb2: use enum phy_mode in the role_store()
This patch modifies the role_store() to use "enum phy_mode" instead
of the local "bool" for host/device mode selection.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The previous code assumed a channel has otg capability if a channel
has interrupt property. But, it is not good because:
- Battery charging feature also needs interrupt property.
- Some R-Car Gen3 SoCs (e.g. R-Car D3) don't have OTG capability.
So, this patch checks whether usb 2.0 host node has dr_mode property or
not. If it has 'dr_mode = "otg";', this driver enables otg capability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Biju Das [Mon, 9 Oct 2017 10:22:23 +0000 (11:22 +0100)]
phy: rcar-gen2: Add r8a7743/5 support
Add USB PHY support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5)
USB PHY is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Douglas Anderson [Fri, 22 Sep 2017 16:44:06 +0000 (09:44 -0700)]
phy: rockchip-typec: Do the calibration more correctly
Calculate the calibration code as per the docs. The docs talk about
reading and averaging the pullup and pulldown calibration codes. They
also talk about adding in some adjustment codes. Let's do what the
docs say.
In practice this doesn't seem to matter a whole lot. On a device I
tested the pullup and pulldown codes were nearly the same (0x23 and
0x24) and the adjustment codes were 0.
Reviewed-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Douglas Anderson [Fri, 22 Sep 2017 16:44:05 +0000 (09:44 -0700)]
phy: rockchip-typec: Avoid magic numbers + add delays in aux calib
NOTE: nothing is known to be fixed by this change, but it does enforce
some delays that are documented to be necessary. Possibly this could
fix some corner cases.
The function tcphy_dp_aux_calibration(), like most of the functions in
the type C PHY, is mostly undocumented and filled with mysterious,
hardcoded numbers.
Let's attempt to try to document some of these numbers and clean the
function up a little bit. Here's the actual cleanup that happened
here:
1. All magic numbers were replaced with bit definitions.
2. For registers that we modify multiple times I now keep track of the
value of the register rather than randomly doing a
read/modify/write or just hardcoding a new number based on knowing
what the old number was.
3. Delay 10 ms (vs 1 ms) after writing the calibration code. No idea
if this is important but it matches the example in the docs.
4. Whenever setting a "delayed" version of a signal always put an
explicit delay in the code. No known problems were seen without
this delay but it seems wise to have it. Whenever a delay of "at
least 100 ns" was specified I used a delay of 1 us.
5. Added comments to some of the bits of code.
6. Removed duplicate setting of TX_ANA_CTRL_REG_5 (to 0)
7. Moved setting of TX_ANA_CTRL_REG_3 to the same place it was in the
sample code. Note that TX_ANA_CTRL_REG_3 ought to be initted to 0
(and elsewhere we assume that we just got a reset), but it seems
fine to be explicit.
8. Treats the calibration code as a 7-bit two's complement number.
This isn't strictly required, but seems slightly cleaner. The docs
say "treat this as a two's complement number, but it should never
be negative". If we ever read the "adjustment" codes as documented
then perhaps the two's complement bit will matter more.
There are still a few weird / mysterious things around aux init and
this doesn't attempt to fix all of them. Mostly it's aimed at doing
changes that should be _very_ safe and add a lot of clarity. Things
specifically not done:
A) Resolve the fact that some registers are read/modify/write and
others are explicitly initted to a value. We always call
tcphy_dp_aux_calibration() right after resetting the PHY so it's
probably not critical, but it's a little weird that the code is
inconsistent.
B) Fully resolve the documented init sequence with the current one.
We still have a few mystery steps and we also leave out turning on
TXDA_DRV_LDO_BG_FB_EN and TXDA_DRV_LDO_BG_REF_EN, which is in the
sample code.
C) Clean things up to read all the bits of the calibration code. This
will hopefully come in a followup change.
This also doesn't attempt to document any of the other parts of the
PHY--just the aux init which is all I got docs for.
Reviewed-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
extcon: Split out extcon header file for consumer and provider device
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Linus Torvalds [Sun, 22 Oct 2017 20:19:12 +0000 (16:19 -0400)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A fix for a broken commit in the previous pull breaking automatic
module loading of input handlers, such ad evdev"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: do not use property bits when generating module alias
Dmitry Torokhov [Sun, 22 Oct 2017 18:42:29 +0000 (11:42 -0700)]
Input: do not use property bits when generating module alias
The commit 8724ecb07229 ("Input: allow matching device IDs on property
bits") started using property bits when generating module aliases for input
handlers, but did not adjust the generation of MODALIAS attribute on input
device uevents, breaking automatic module loading. Given that no handler
currently uses property bits in their module tables, let's revert this part
of the commit for now.
Linus Torvalds [Sun, 22 Oct 2017 10:58:23 +0000 (06:58 -0400)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes addressing the following issues:
- The last polishing for the TLB code, removing the last BUG_ON() and
the debug file along with tidying up the lazy TLB code.
- Prevent triple fault on 1st Gen. 486 caused by stupidly calling the
early IDT setup after the first function which causes a fault which
should be caught by the exception table.
- Limit the mmap of /dev/mem to valid addresses
- Prevent late microcode loading on Broadwell X
- Remove a redundant assignment in the cache info code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/mm: Remove debug/x86/tlb_defer_switch_to_init_mm
x86/mm: Tidy up "x86/mm: Flush more aggressively in lazy TLB mode"
x86/mm/64: Remove the last VM_BUG_ON() from the TLB code
x86/microcode/intel: Disable late loading on model 79
x86/idt: Initialize early IDT before cr4_init_shadow()
x86/cpu/intel_cacheinfo: Remove redundant assignment to 'this_leaf'
Linus Torvalds [Sun, 22 Oct 2017 10:56:25 +0000 (06:56 -0400)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix to make the cs5535 clock event driver robust agaist
spurious interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/cs5535: Improve resilience to spurious interrupts
Linus Torvalds [Sun, 22 Oct 2017 10:54:42 +0000 (06:54 -0400)]
Merge branch 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp/hotplug fix from Thomas Gleixner:
"The recent rework of the callback invocation missed to cleanup the
leftovers of the operation, so under certain circumstances a
subsequent CPU hotplug operation accesses stale data and crashes.
Clean it up."
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Reset node state after operation
Linus Torvalds [Sun, 22 Oct 2017 10:52:53 +0000 (06:52 -0400)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A series of fixes for perf tooling:
- Make xyarray return the X/Y size correctly which fixes a crash in
the exit code.
- Fix the libc path in test so it works not only on Debian/Ubuntu
correctly
- Check for eBPF file existance and output a useful error message
instead of failing to compile a non existant file
- Make sure perf_hpp_fmt is not longer references before freeing it
- Use list_del_init() in the histogram code to prevent a crash when
the already deleted element is deleted again
- Remove the leftovers of the removed '-l' option
- Add reviewer entries to the MAINTAINERS file"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf test shell trace+probe_libc_inet_pton.sh: Be compatible with Debian/Ubuntu
perf xyarray: Fix wrong processing when closing evsel fd
perf buildid-list: Fix crash when processing PERF_RECORD_NAMESPACE
perf record: Fix documentation for a inexistent option '-l'
perf tools: Add long time reviewers to MAINTAINERS
perf tools: Check wether the eBPF file exists in event parsing
perf hists: Add extra integrity checks to fmt_free()
perf hists: Fix crash in perf_hpp__reset_output_field()
Linus Torvalds [Sun, 22 Oct 2017 10:42:58 +0000 (06:42 -0400)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of small fixes mostly in the irq drivers area:
- Make the tango irq chip work correctly, which requires a new
function in the generiq irq chip implementation
- A set of updates to the GIC-V3 ITS driver removing a bogus BUG_ON()
and parsing the VCPU table size correctly"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack()
irqchip/tango: Use irq_gc_mask_disable_and_ack_set
genirq: generic chip: Add irq_gc_mask_disable_and_ack_set()
irqchip/gic-v3-its: Add missing changes to support 52bit physical address
irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size
irqchip/gic-v3-its: Fix the incorrect BUG_ON in its_init_vpe_domain()
DT: arm,gic-v3: Update the ITS size in the examples
Pull networking fixes from David Miller:
"A little more than usual this time around. Been travelling, so that is
part of it.
Anyways, here are the highlights:
1) Deal with memcontrol races wrt. listener dismantle, from Eric
Dumazet.
2) Handle page allocation failures properly in nfp driver, from Jaku
Kicinski.
3) Fix memory leaks in macsec, from Sabrina Dubroca.
4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.
5) Several fixes in bnxt_en driver, including preventing potential
NVRAM parameter corruption from Michael Chan.
6) Fix for KRACK attacks in wireless, from Johannes Berg.
7) rtnetlink event generation fixes from Xin Long.
8) Deadlock in mlxsw driver, from Ido Schimmel.
9) Disallow arithmetic operations on context pointers in bpf, from
Jakub Kicinski.
10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
Xin Long.
11) Only TCP is supported for sockmap, make that explicit with a
check, from John Fastabend.
12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.
13) Fix panic in packet_getsockopt(), also from Eric Dumazet.
14) Add missing locked in hv_sock layer, from Dexuan Cui.
15) Various aquantia bug fixes, including several statistics handling
cures. From Igor Russkikh et al.
16) Fix arithmetic overflow in devmap code, from John Fastabend.
17) Fix busted socket memory accounting when we get a fault in the tcp
zero copy paths. From Willem de Bruijn.
18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
ipv6: flowlabel: do not leave opt->tot_len with garbage
of_mdio: Fix broken PHY IRQ in case of probe deferral
textsearch: fix typos in library helpers
rxrpc: Don't release call mutex on error pointer
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
net: stmmac: Fix stmmac_get_rx_hwtstamp()
net: stmmac: Add missing call to dev_kfree_skb()
mlxsw: spectrum_router: Configure TIGCR on init
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
net: ethtool: remove error check for legacy setting transceiver type
soreuseport: fix initialization race
net: bridge: fix returning of vlan range op errors
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
bpf: add test cases to bpf selftests to cover all access tests
bpf: fix pattern matches for direct packet access
bpf: fix off by one for range markings with L{T, E} patterns
bpf: devmap fix arithmetic overflow in bitmap_size calculation
net: aquantia: Bad udp rate on default interrupt coalescing
net: aquantia: Enable coalescing management via ethtool interface
...
Bernd Edlinger [Sat, 21 Oct 2017 06:51:30 +0000 (06:51 +0000)]
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
This is the possible reason for different hard to reproduce
problems on my ARMv7-SMP test system.
The symptoms are in recent kernels imprecise external aborts,
and in older kernels various kinds of network stalls and
unexpected page allocation failures.
My testing indicates that the trouble started between v4.5 and v4.6
and prevails up to v4.14.
Using the dirty_tx before acquiring the spin lock is clearly
wrong and was first introduced with v4.6.
Fixes: e3ad57c96715 ("stmmac: review RX/TX ring management") Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 21 Oct 2017 19:26:23 +0000 (12:26 -0700)]
ipv6: flowlabel: do not leave opt->tot_len with garbage
When syzkaller team brought us a C repro for the crash [1] that
had been reported many times in the past, I finally could find
the root cause.
If FlowLabel info is merged by fl6_merge_options(), we leave
part of the opt_space storage provided by udp/raw/l2tp with random value
in opt_space.tot_len, unless a control message was provided at sendmsg()
time.
Then ip6_setup_cork() would use this random value to perform a kzalloc()
call. Undefined behavior and crashes.
Fix is to properly set tot_len in fl6_merge_options()
At the same time, we can also avoid consuming memory and cpu cycles
to clear it, if every option is copied via a kmemdup(). This is the
change in ip6_setup_cork().
Depending on whether the PHY driver will fall back to polling, Ethernet
may or may not work.
To fix this:
1. Switch of_mdiobus_register_phy() from irq_of_parse_and_map() to
of_irq_get().
Unlike the former, the latter returns -EPROBE_DEFER if the
interrupt controller is not yet available, so this condition can be
detected.
Other errors are handled the same as before, i.e. use the passed
mdio->irq[addr] as interrupt.
2. Propagate and handle errors from of_mdiobus_register_phy() and
of_mdiobus_register_device().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 20 Oct 2017 16:01:22 +0000 (17:01 +0100)]
rxrpc: Don't release call mutex on error pointer
Don't release call mutex at the end of rxrpc_kernel_begin_call() if the
call pointer actually holds an error value.
Fixes: 540b1c48c37a ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Fri, 20 Oct 2017 13:37:36 +0000 (14:37 +0100)]
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
Prevent infinite loop by correctly setting the loop condition to
break when i == 10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Fri, 20 Oct 2017 13:37:35 +0000 (14:37 +0100)]
net: stmmac: Fix stmmac_get_rx_hwtstamp()
When using GMAC4 the valid timestamp is from CTX next desc but
we are passing the previous desc to get_rx_timestamp_status()
callback.
Fix this and while at it rework a little bit the function logic.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Fri, 20 Oct 2017 13:37:34 +0000 (14:37 +0100)]
net: stmmac: Add missing call to dev_kfree_skb()
When RX HW timestamp is enabled and a frame is discarded we are
not freeing the skb but instead only setting to NULL the entry.
Add a call to dev_kfree_skb_any() so that skb entry is correctly
freed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 22 Oct 2017 01:46:39 +0000 (21:46 -0400)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
Linus Torvalds [Sun, 22 Oct 2017 01:39:18 +0000 (21:39 -0400)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"MS_I_VERSION fixes - Mimi's fix + missing bits picked from Matthew
(his patch contained a duplicate of the fs/namespace.c fix as well,
but by that point the original fix had already been applied)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Convert fs/*/* to SB_I_VERSION
vfs: fix mounting a filesystem with i_version
David S. Miller [Sun, 22 Oct 2017 01:19:03 +0000 (02:19 +0100)]
Merge branch 'mlxsw-fixes'
Jiri Pirko says:
====================
mlxsw: spectrum: Configure TTL of "inherit" for offloaded tunnels
Petr says:
Currently mlxsw only offloads tunnels that are configured with TTL of "inherit"
(which is the default). However, Spectrum defaults to 255 and the driver
neglects to change the configuration. Thus the tunnel packets from offloaded
tunnels always have TTL of 255, even though tunnels with explicit TTL of 255 are
never actually offloaded.
To fix this, introduce support for TIGCR, the register that keeps the related
bits of global tunnel configuration, and use it on first offload to properly
configure inheritance of TTL of tunnel packets from overlay packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 20 Oct 2017 07:16:16 +0000 (09:16 +0200)]
mlxsw: spectrum_router: Configure TIGCR on init
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 20 Oct 2017 07:16:15 +0000 (09:16 +0200)]
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Söderlund [Thu, 19 Oct 2017 23:32:08 +0000 (01:32 +0200)]
net: ethtool: remove error check for legacy setting transceiver type
Commit 9cab88726929605 ("net: ethtool: Add back transceiver type")
restores the transceiver type to struct ethtool_link_settings and
convert_link_ksettings_to_legacy_settings() but forgets to remove the
error check for the same in convert_legacy_settings_to_link_ksettings().
This prevents older versions of ethtool to change link settings.
# ethtool --version
ethtool version 3.16
# ethtool -s eth0 autoneg on speed 100 duplex full
Cannot set new settings: Invalid argument
not setting speed
not setting duplex
not setting autoneg
While newer versions of ethtool works.
# ethtool --version
ethtool version 4.10
# ethtool -s eth0 autoneg on speed 100 duplex full
[ 57.703268] sh-eth ee700000.ethernet eth0: Link is Down
[ 59.618227] sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Fixes: 19cab88726929605 ("net: ethtool: Add back transceiver type") Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reported-by: Renjith R V <renjith.rv@quest-global.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Thu, 19 Oct 2017 19:00:29 +0000 (15:00 -0400)]
soreuseport: fix initialization race
Syzkaller stumbled upon a way to trigger
WARNING: CPU: 1 PID: 13881 at net/core/sock_reuseport.c:41
reuseport_alloc+0x306/0x3b0 net/core/sock_reuseport.c:39
There are two initialization paths for the sock_reuseport structure in a
socket: Through the udp/tcp bind paths of SO_REUSEPORT sockets or through
SO_ATTACH_REUSEPORT_[CE]BPF before bind. The existing implementation
assumedthat the socket lock protected both of these paths when it actually
only protects the SO_ATTACH_REUSEPORT path. Syzkaller triggered this
double allocation by running these paths concurrently.
This patch moves the check for double allocation into the reuseport_alloc
function which is protected by a global spin lock.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection") Fixes: c125e80b8868 ("soreuseport: fast reuseport TCP socket selection") Signed-off-by: Craig Gallek <kraig@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix returning of vlan range op errors
When vlan tunnels were introduced, vlan range errors got silently
dropped and instead 0 was returned always. Restore the previous
behaviour and return errors to user-space.
Fixes: efa5356b0d97 ("bridge: per vlan dst_metadata netlink support") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 19 Oct 2017 16:40:39 +0000 (12:40 -0400)]
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
Syzkaller hits WARN_ON(sk->sk_wmem_queued) in sk_stream_kill_queues
after triggering an EFAULT in __zerocopy_sg_from_iter.
On this error, skb_zerocopy_stream_iter resets the skb to its state
before the operation with __pskb_trim. It cannot kfree_skb like
datagram callers, as the skb may have data from a previous send call.
__pskb_trim calls skb_condense for unowned skbs, which adjusts their
truesize. These tcp skbuffs are owned and their truesize must add up
to sk_wmem_queued. But they match because their skb->sk is NULL until
tcp_transmit_skb.
Temporarily set skb->sk when calling __pskb_trim to signal that the
skbuffs are owned and avoid the skb_condense path.
Fixes: 52267790ef52 ("sock: add MSG_ZEROCOPY") Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 21 Oct 2017 23:56:10 +0000 (00:56 +0100)]
Merge branch 'bpf-range-marking-fixes'
Daniel Borkmann says:
====================
Two BPF fixes for range marking
The set contains two fixes for direct packet access range
markings and test cases for all direct packet access patterns
that the verifier matches on.
They are targeted for net tree, note that once net gets merged
into net-next, there will be a minor merge conflict due to
signature change of the function find_good_pkt_pointers() as
well as data_meta patterns present in net-next tree. You can
just add bool false to the data_meta patterns and I will
follow-up with properly converting the patterns for data_meta
in a similar way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 21 Oct 2017 00:34:23 +0000 (02:34 +0200)]
bpf: add test cases to bpf selftests to cover all access tests
Lets add test cases to cover really all possible direct packet
access tests for good/bad access cases so we keep tracking them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 21 Oct 2017 00:34:22 +0000 (02:34 +0200)]
bpf: fix pattern matches for direct packet access
Alexander had a test program with direct packet access, where
the access test was in the form of data + X > data_end. In an
unrelated change to the program LLVM decided to swap the branches
and emitted code for the test in form of data + X <= data_end.
We hadn't seen these being generated previously, thus verifier
would reject the program. Therefore, fix up the verifier to
detect all test cases, so we don't run into such issues in the
future.
Fixes: b4e432f1000a ("bpf: enable BPF_J{LT, LE, SLT, SLE} opcodes in verifier") Reported-by: Alexander Alemayhu <alexander@alemayhu.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-hirsute-kernel.git / log