sh: also without PM_RUNTIME pm_runtime.o must be built
When CONFIG_PM_RUNTIME is off, drivers/sh/pm_runtime.o still has to be
built on sh platforms, because then it provides means to statically
switch on device PM clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 10 Jan 2012 07:30:37 +0000 (16:30 +0900)]
sh: Ensure IRQs are enabled across do_notify_resume().
do_notify_resume() can trigger the freezer via the try_to_freeze() path
(both explicitly through a redundant call in do_signal() or via
get_signal_to_deliver()). That IRQs were disabled across this callsite
became apparent with the might_sleep() introduction in try_to_freeze() by
Tejun in a0acae0e886d44bd5ce6d2f173c1ace0fcf0d9f6, resulting in:
BUG: sleeping function called from invalid context at include/linux/freezer.h:45
in_atomic(): 0, irqs_disabled(): 1, pid: 819, name: ntpd
no locks held by ntpd/819.
Stack: (0x9c81be80 to 0x9c81c000)
...
The renesas_usbhs driver doesn't use the clk functions. So, even if we
adds "CLKDEV_DEV_ID("renesas_usbhs.0", ...)" only, we cannot use the USB
controller because clk_late_init() will disable the clock by "usb0".
So, the patch also removes the "CLKDEV_CON_ID("usb0", ...)".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Jesper Juhl [Sun, 8 Jan 2012 21:44:29 +0000 (22:44 +0100)]
audit: always follow va_copy() with va_end()
A call to va_copy() should always be followed by a call to va_end() in
the same function. In kernel/autit.c::audit_log_vformat() this is not
always done. This patch makes sure va_end() is always called.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric Paris <eparis@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
...
for (i = 0; i < usg->count; i++) {
u64 addr;
void* p;
if (usg->sg[i].count >
((dev->adapter_info.options &
AAC_OPT_NEW_COMM) ?
(dev->scsi_host_ptr->max_sectors << 9) :
65536)) {
rcode = -EINVAL;
goto cleanup;
... this 'goto' makes 'usg' go out of scope and leak the memory we
allocated.
Other exits properly kfree(usg), it's just here it is neglected.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 8 Jan 2012 22:05:48 +0000 (14:05 -0800)]
Merge tag 'infiniband-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
infiniband changes for 3.3 merge window
* tag 'infiniband-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
rdma/core: Fix sparse warnings
RDMA/cma: Fix endianness bugs
RDMA/nes: Fix terminate during AE
RDMA/nes: Make unnecessarily global nes_set_pau() static
RDMA/nes: Change MDIO bus clock to 2.5MHz
IB/cm: Fix layout of APR message
IB/mlx4: Fix SL to 802.1Q priority-bits mapping for IBoE
IB/qib: Default some module parameters optimally
IB/qib: Optimize locking for get_txreq()
IB/qib: Fix a possible data corruption when receiving packets
IB/qib: Eliminate 64-bit jiffies use
IB/qib: Fix style issues
IB/uverbs: Protect QP multicast list
Linus Torvalds [Sun, 8 Jan 2012 21:39:24 +0000 (13:39 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
max1111.c: fix checkpatch warning
hwmon: (lm75) fix checkpatch warnings
hwmon: (lm80) fix checkpatch messages
hwmon: replaced strict_str* with kstr*
hwmon: (lm75) fix checkpatch warning
hwmon: (lm75) added error handling
hwmon: (ltc4261) set data->valid to 0 if error
hwmon: (f75375s) Add support for F75387SG/RG
hwmon: (f75375s) Disable setting DC fan control mode for F75373
hwmon: (f75375s) Initialize pwmX_mode and pwmX_enable if there is no platform data
hwmon: (f75375s) Fix value range for PWM modes
hwmon: (f75375s) Use standard sysfs attribute names
hwmon: (f75375s) Fix checkpatch errors and warnings
hwmon: (pmbus/zl6100) Only instantiate external temperature sensor if enabled
hwmon: (pmbus/zl6100) Add support for Ericsson BMR45[0,1] and BMR46[2,3,4]
hwmon: (pmbus/zl6100) Add support for ZL2005
hwmon: (pmbus/adm1275) Validate device ID
Linus Torvalds [Sun, 8 Jan 2012 21:35:24 +0000 (13:35 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (36 commits)
mfd: Clearing events requires event registers to be writable for da9052-core
mfd: Fix annotations in da9052-core
gpiolib: Mark da9052 driver broken
mfd: Declare da9052_regmap_config for the bus drivers
MFD: DA9052/53 MFD core module add SPI support v2
MFD: DA9052/53 MFD core module
regmap: Add irq_base accessor to regmap_irq
regmap: Allow drivers to reinitialise the register cache at runtime
regmap: Add trace event for successful cache reads
regmap: Allow regmap_update_bits() users to detect changes
regmap: Report if we actually handled an interrupt in regmap-irq
regmap: Fix rbtreee build when not using debugfs
regmap: Provide debugfs dump of the rbtree cache data
regmap: Do debugfs init before cache init
regmap: Suppress noop writes in regmap_update_bits()
regmap: Remove indexed cache type
regmap: Drop check whether a register is readable in regcache_read
regmap: Properly round cache_word_size
regmap: Add support for 10/14 register formating
regmap: Try cached read before checking if a hardware read is possible
...
Linus Torvalds [Sun, 8 Jan 2012 21:28:33 +0000 (13:28 -0800)]
Merge tag 'md-3.3' of git://neil.brown.name/md
md update for 3.3
Big change is new hot-replacement.
A slot in an array can hold 2 devices - one that
wants-replacement and one that is the replacement.
Once the replacement is built - either from the
original or (in the case of errors) from elsewhere,
the wants-replacement device will be removed.
* tag 'md-3.3' of git://neil.brown.name/md: (36 commits)
md/raid1: Mark device want_replacement when we see a write error.
md/raid1: If there is a spare and a want_replacement device, start replacement.
md/raid1: recognise replacements when assembling arrays.
md/raid1: handle activation of replacement device when recovery completes.
md/raid1: Allow a failed replacement device to be removed.
md/raid1: Allocate spare to store replacement devices and their bios.
md/raid1: Replace use of mddev->raid_disks with conf->raid_disks.
md/raid10: If there is a spare and a want_replacement device, start replacement.
md/raid10: recognise replacements when assembling array.
md/raid10: Allow replacement device to be replace old drive.
md/raid10: handle recovery of replacement devices.
md/raid10: Handle replacement devices during resync.
md/raid10: writes should get directed to replacement as well as original.
md/raid10: allow removal of failed replacement devices.
md/raid10: preferentially read from replacement device if possible.
md/raid10: change read_balance to return an rdev
md/raid10: prepare data structures for handling replacement.
md/raid5: Mark device want_replacement when we see a write error.
md/raid5: If there is a spare and a want_replacement device, start replacement.
md/raid5: recognise replacements when assembling array.
...
Linus Torvalds [Sun, 8 Jan 2012 21:21:22 +0000 (13:21 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Linus Torvalds [Sun, 8 Jan 2012 21:10:57 +0000 (13:10 -0800)]
Merge branch 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
GFS2: local functions should be static
GFS2: We only need one ACL getting function
GFS2: Fix multi-block allocation
GFS2: decouple quota allocations from block allocations
GFS2: split function rgblk_search
GFS2: Fix up "off by one" in the previous patch
GFS2: move toward a generic multi-block allocator
GFS2: O_(D)SYNC support for fallocate
GFS2: remove vestigial al_alloced
GFS2: combine gfs2_alloc_block and gfs2_alloc_di
GFS2: Add non-try locks back to get_local_rgrp
GFS2: f_ra is always valid in dir readahead function
GFS2: Fix very unlikley memory leak in ACL xattr code
GFS2: More automated code analysis fixes
GFS2: Add readahead to sequential directory traversal
GFS2: Fix up REQ flags
Linus Torvalds [Sun, 8 Jan 2012 21:05:29 +0000 (13:05 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (22 commits)
xfs: mark the xfssyncd workqueue as non-reentrant
xfs: simplify xfs_qm_detach_gdquots
xfs: fix acl count validation in xfs_acl_from_disk()
xfs: remove unused XBT_FORCE_SLEEP bit
xfs: remove XFS_QMOPT_DQSUSER
xfs: kill xfs_qm_idtodq
xfs: merge xfs_qm_dqinit_core into the only caller
xfs: add a xfs_dqhold helper
xfs: simplify xfs_qm_dqattach_grouphint
xfs: nest qm_dqfrlist_lock inside the dquot qlock
xfs: flatten the dquot lock ordering
xfs: implement lazy removal for the dquot freelist
xfs: remove XFS_DQ_INACTIVE
xfs: cleanup xfs_qm_dqlookup
xfs: cleanup dquot locking helpers
xfs: remove the sync_mode argument to xfs_qm_dqflush_all
xfs: remove xfs_qm_sync
xfs: make sure to really flush all dquots in xfs_qm_quotacheck
xfs: untangle SYNC_WAIT and SYNC_TRYLOCK meanings for xfs_qm_dqflush
xfs: remove the lid_size field in struct log_item_desc
...
Linus Torvalds [Sun, 8 Jan 2012 20:19:57 +0000 (12:19 -0800)]
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
Linus Torvalds [Sat, 7 Jan 2012 20:18:52 +0000 (12:18 -0800)]
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
devicetree/next changes queued for v3.3 merge window
* tag 'devicetree-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
ARM: prom.h: Fix build error by removing unneeded header file
irq: check domain hwirq range for DT translate
dt: add empty of_get_node/of_put_node functions
of/pdt: fix section mismatch warning
i2c-designware: add OF binding support
dt/i2c: Enumerate some of the known trivial i2c devices
dt: reform for_each_property to for_each_property_of_node
ARM/of: allow *machine_desc.dt_compat to be const
of/base: Take NULL string into account for property with multiple strings
OF/device-tree: Add some entries to vendor-prefixes.txt
Fix up trivial add-add conflicts in include/linux/of.h
Linus Torvalds [Sat, 7 Jan 2012 20:16:27 +0000 (12:16 -0800)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
spi changes queued up for v3.3 merge window
* tag 'spi-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix device unregistration when unregistering the bus master
spi-topcliff-pch: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
spi-topcliff-pch: Support new device LAPIS Semiconductor ML7831 IOH
spi/omap: Correct the error path
spi/omap: call pm_runtime_disable in error path and remove
spi/omap: Use a workqueue per omap2_mcspi controller
Linus Torvalds [Sat, 7 Jan 2012 20:15:36 +0000 (12:15 -0800)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
Linus Torvalds [Sat, 7 Jan 2012 20:03:30 +0000 (12:03 -0800)]
Merge branch 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
Miklos Szeredi [Mon, 21 Nov 2011 11:11:33 +0000 (12:11 +0100)]
vfs: prevent remount read-only if pending removes
If there are any inodes on the super block that have been unlinked
(i_nlink == 0) but have not yet been deleted then prevent the
remounting the super block read-only.
Miklos Szeredi [Mon, 21 Nov 2011 11:11:32 +0000 (12:11 +0100)]
vfs: count unlinked inodes
Add a new counter to the superblock that keeps track of unlinked but
not yet deleted inodes.
Do not WARN_ON if set_nlink is called with zero count, just do a
ratelimited printk. This happens on xfs and probably other
filesystems after an unclean shutdown when the filesystem reads inodes
which already have zero i_nlink. Reported by Christoph Hellwig.
Miklos Szeredi [Mon, 21 Nov 2011 11:11:31 +0000 (12:11 +0100)]
vfs: protect remounting superblock read-only
Currently remouting superblock read-only is racy in a major way.
With the per mount read-only infrastructure it is now possible to
prevent most races, which this patch attempts.
Before starting the remount read-only, iterate through all mounts
belonging to the superblock and if none of them have any pending
writes, set sb->s_readonly_remount. This indicates that remount is in
progress and no further write requests are allowed. If the remount
succeeds set MS_RDONLY and reset s_readonly_remount.
If the remounting is unsuccessful just reset s_readonly_remount.
This can result in transient EROFS errors, despite the fact the
remount failed. Unfortunately hodling off writes is difficult as
remount itself may touch the filesystem (e.g. through load_nls())
which would deadlock.
A later patch deals with delayed writes due to nlink going to zero.
Linus Torvalds [Sat, 7 Jan 2012 02:15:25 +0000 (18:15 -0800)]
Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'for-linus' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (207 commits)
ARM: 7267/1: Remove BUILD_BUG_ON from asm/bug.h
ARM: 7269/1: mach-sa1100: fix sched_clock breakage
ARM: 7198/1: arm/imx6: add restart support for imx6q
ARM: restart: remove the now empty arch_reset()
ARM: restart: remove comments about adding code to arch_reset()
ARM: restart: lpc32xx & u300: remove unnecessary printk
ARM: restart: plat-samsung: remove plat/reset.h and s5p_reset_hook
ARM: restart: w90x900: use new restart hook
ARM: restart: Versatile Express: use new restart hook
ARM: restart: versatile: use new restart hook
ARM: restart: u300: use new restart hook
ARM: restart: tegra: use new restart hook
ARM: restart: spear: use new restart hook
ARM: restart: shark: use new restart hook
ARM: restart: sa1100: use new restart hook
ARM: 7252/1: restart: S5PV210: use new restart hook
ARM: 7251/1: restart: S5PC100: use new restart hook
ARM: 7250/1: restart: S5P64X0: use new restart hook
ARM: 7266/1: restart: S3C64XX: use new restart hook
ARM: 7265/1: restart: S3C24XX: use new restart hook
...
Fix up trivial conflict in arch/arm/mm/init.c due to removal of
memblock_init() clashing with the movement of the sorting of the meminfo
array.
Linus Torvalds [Sat, 7 Jan 2012 02:03:30 +0000 (18:03 -0800)]
Merge branch 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
Linus Torvalds [Sat, 7 Jan 2012 02:02:43 +0000 (18:02 -0800)]
Merge branch 'misc-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
* 'misc-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
ia64: pcibr: Use kmemdup rather than duplicating its implementation
ia64: sn: Use kmemdup rather than duplicating its implementation
ia64: tioca: Use kmemdup rather than duplicating its implementation
[IA64] Merge overlapping reserved regions at boot
Linus Torvalds [Sat, 7 Jan 2012 01:59:33 +0000 (17:59 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (56 commits)
m68k: allow ColdFire 547x and 548x CPUs to be built with MMU enabled
m68k/Kconfig: Separate classic m68k and coldfire early
m68k: add ColdFire with MMU enabled support to the m68k mem init code
m68k: do not use m68k startup or interrupt code for ColdFire CPUs
m68k: add ColdFire FPU support for the V4e ColdFire CPUs
m68k: adjustments to stack frame for ColdFire with MMU enabled
m68k: use non-MMU linker script for ColdFire MMU builds
m68k: ColdFire with MMU enabled uses same clocking code as non-MMU
m68k: add code to setup a ColdFire 54xx platform when MMU enabled
m68k: use non-MMU entry.S code when compiling for ColdFire CPU
m68k: create ColdFire MMU pgalloc code
m68k: compile appropriate mm arch files for ColdFire MMU support
m68k: ColdFire V4e MMU paging init code and miss handler
m68k: use ColdFire MMU read/write bit flags when ioremapping
m68k: modify cache push and clear code for ColdFire with MMU enable
m68k: use tracehook_report_syscall_entry/exit for ColdFire MMU ptrace path
m68k: ColdFire V4e MMU context support code
m68k: MMU enabled ColdFire needs 8k ELF alignment
m68k: set ColdFire MMU page size
m68k: define PAGE_OFFSET_RAW for ColdFire CPU with MMU enabled
...
Linus Torvalds [Sat, 7 Jan 2012 01:58:22 +0000 (17:58 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1958 commits)
net: pack skb_shared_info more efficiently
net_sched: red: split red_parms into parms and vars
net_sched: sfq: extend limits
cnic: Improve error recovery on bnx2x devices
cnic: Re-init dev->stats_addr after chip reset
net_sched: Bug in netem reordering
bna: fix sparse warnings/errors
bna: make ethtool_ops and strings const
xgmac: cleanups
net: make ethtool_ops const
vmxnet3" make ethtool ops const
xen-netback: make ops structs const
virtio_net: Pass gfp flags when allocating rx buffers.
ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call
netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call
igb: reset PHY after recovering from PHY power down
igb: add basic runtime PM support
igb: Add support for byte queue limits.
e1000: cleanup CE4100 MDIO registers access
e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove
...
Linus Torvalds [Fri, 6 Jan 2012 22:00:12 +0000 (14:00 -0800)]
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Use "do { } while(0)" for empty lock_cmos()/unlock_cmos() macros
x86: Use "do { } while(0)" for empty flush_tlb_fix_spurious_fault() macro
x86, CPU: Drop superfluous get_cpu_cap() prototype
arch/x86/mm/pageattr.c: Quiet sparse noise; local functions should be static
arch/x86/kernel/ptrace.c: Quiet sparse noise
x86: Use kmemdup() in copy_thread(), rather than duplicating its implementation
x86: Replace the EVT_TO_HPET_DEV() macro with an inline function
Linus Torvalds [Fri, 6 Jan 2012 21:59:14 +0000 (13:59 -0800)]
Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86: Fix atomic64_xxx_cx8() functions
x86: Fix and improve cmpxchg_double{,_local}()
x86_64, asm: Optimise fls(), ffs() and fls64()
x86, bitops: Move fls64.h inside __KERNEL__
x86: Fix and improve percpu_cmpxchg{8,16}b_double()
x86: Report cpb and eff_freq_ro flags correctly
x86/i386: Use less assembly in strlen(), speed things up a bit
x86: Use the same node_distance for 32 and 64-bit
x86: Fix rflags in FAKE_STACK_FRAME
x86: Clean up and extend do_int3()
x86: Call do_notify_resume() with interrupts enabled
x86/div64: Add a micro-optimization shortcut if base is power of two
x86-64: Cleanup some assembly entry points
x86-64: Slightly shorten line system call entry and exit paths
x86-64: Reduce amount of redundant code generated for invalidate_interruptNN
x86-64: Slightly shorten int_ret_from_sys_call
x86, efi: Convert efi_phys_get_time() args to physical addresses
x86: Default to vsyscall=emulate
x86-64: Set siginfo and context on vsyscall emulation faults
x86: consolidate xchg and xadd macros
...
Linus Torvalds [Fri, 6 Jan 2012 21:58:21 +0000 (13:58 -0800)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Skip cpus with apic-ids >= 255 in !x2apic_mode
x86, x2apic: Allow "nox2apic" to disable x2apic mode setup by BIOS
x86, x2apic: Fallback to xapic when BIOS doesn't setup interrupt-remapping
x86, acpi: Skip acpi x2apic entries if the x2apic feature is not present
x86, apic: Add probe() for apic_flat
x86: Simplify code by removing a !SMP #ifdefs from 'struct cpuinfo_x86'
x86: Convert per-cpu counter icr_read_retry_count into a member of irq_stat
x86: Add per-cpu stat counter for APIC ICR read tries
pci, x86/io-apic: Allow PCI_IOAPIC to be user configurable on x86
x86: Fix the !CONFIG_NUMA build of the new CPU ID fixup code support
x86: Add NumaChip support
x86: Add x86_init platform override to fix up NUMA core numbering
x86: Make flat_init_apic_ldr() available
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Linus Torvalds [Fri, 6 Jan 2012 16:33:28 +0000 (08:33 -0800)]
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
sched/tracing: Add a new tracepoint for sleeptime
sched: Disable scheduler warnings during oopses
sched: Fix cgroup movement of waking process
sched: Fix cgroup movement of newly created process
sched: Fix cgroup movement of forking process
sched: Remove cfs bandwidth period check in tg_set_cfs_period()
sched: Fix load-balance lock-breaking
sched: Replace all_pinned with a generic flags field
sched: Only queue remote wakeups when crossing cache boundaries
sched: Add missing rcu_dereference() around ->real_parent usage
[S390] fix cputime overflow in uptime_proc_show
[S390] cputime: add sparse checking and cleanup
sched: Mark parent and real_parent as __rcu
sched, nohz: Fix missing RCU read lock
sched, nohz: Set the NOHZ_BALANCE_KICK flag for idle load balancer
sched, nohz: Fix the idle cpu check in nohz_idle_balance
sched: Use jump_labels for sched_feat
sched/accounting: Fix parameter passing in task_group_account_field
sched/accounting: Fix user/system tick double accounting
sched/accounting: Re-use scheduler statistics for the root cgroup
...
Fix up conflicts in
- arch/ia64/include/asm/cputime.h, include/asm-generic/cputime.h
usecs_to_cputime64() vs the sparse cleanups
- kernel/sched/fair.c, kernel/time/tick-sched.c
scheduler changes in multiple branches
Linus Torvalds [Fri, 6 Jan 2012 16:02:58 +0000 (08:02 -0800)]
Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (106 commits)
perf kvm: Fix copy & paste error in description
perf script: Kill script_spec__delete
perf top: Fix a memory leak
perf stat: Introduce get_ratio_color() helper
perf session: Remove impossible condition check
perf tools: Fix feature-bits rework fallout, remove unused variable
perf script: Add generic perl handler to process events
perf tools: Use for_each_set_bit() to iterate over feature flags
perf tools: Unify handling of features when writing feature section
perf report: Accept fifos as input file
perf tools: Moving code in some files
perf tools: Fix out-of-bound access to struct perf_session
perf tools: Continue processing header on unknown features
perf tools: Improve macros for struct feature_ops
perf: builtin-record: Document and check that mmap_pages must be a power of two.
perf: builtin-record: Provide advice if mmap'ing fails with EPERM.
perf tools: Fix truncated annotation
perf script: look up thread using tid instead of pid
perf tools: Look up thread names for system wide profiling
perf tools: Fix comm for processes with named threads
...
Linus Torvalds [Fri, 6 Jan 2012 16:02:40 +0000 (08:02 -0800)]
Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
cpu: Export cpu_up()
rcu: Apply ACCESS_ONCE() to rcu_boost() return value
Revert "rcu: Permit rt_mutex_unlock() with irqs disabled"
docs: Additional LWN links to RCU API
rcu: Augment rcu_batch_end tracing for idle and callback state
rcu: Add rcutorture tests for srcu_read_lock_raw()
rcu: Make rcutorture test for hotpluggability before offlining CPUs
driver-core/cpu: Expose hotpluggability to the rest of the kernel
rcu: Remove redundant rcu_cpu_stall_suppress declaration
rcu: Adaptive dyntick-idle preparation
rcu: Keep invoking callbacks if CPU otherwise idle
rcu: Irq nesting is always 0 on rcu_enter_idle_common
rcu: Don't check irq nesting from rcu idle entry/exit
rcu: Permit dyntick-idle with callbacks pending
rcu: Document same-context read-side constraints
rcu: Identify dyntick-idle CPUs on first force_quiescent_state() pass
rcu: Remove dynticks false positives and RCU failures
rcu: Reduce latency of rcu_prepare_for_idle()
rcu: Eliminate RCU_FAST_NO_HZ grace-period hang
rcu: Avoid needlessly IPIing CPUs at GP end
...
Linus Torvalds [Fri, 6 Jan 2012 15:54:53 +0000 (07:54 -0800)]
Merge branch 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
memblock: Reimplement memblock allocation using reverse free area iterator
memblock: Kill early_node_map[]
score: Use HAVE_MEMBLOCK_NODE_MAP
s390: Use HAVE_MEMBLOCK_NODE_MAP
mips: Use HAVE_MEMBLOCK_NODE_MAP
ia64: Use HAVE_MEMBLOCK_NODE_MAP
SuperH: Use HAVE_MEMBLOCK_NODE_MAP
sparc: Use HAVE_MEMBLOCK_NODE_MAP
powerpc: Use HAVE_MEMBLOCK_NODE_MAP
memblock: Implement memblock_add_node()
memblock: s/memblock_analyze()/memblock_allow_resize()/ and update users
memblock: Track total size of regions automatically
powerpc: Cleanup memblock usage
memblock: Reimplement memblock_enforce_memory_limit() using __memblock_remove()
memblock: Make memblock functions handle overflowing range @size
memblock: Reimplement __memblock_remove() using memblock_isolate_range()
memblock: Separate out memblock_isolate_range() from memblock_set_node()
memblock: Kill memblock_init()
memblock: Kill sentinel entries at the end of static region arrays
memblock: Add __memblock_dump_all()
...
Linus Torvalds [Fri, 6 Jan 2012 15:53:52 +0000 (07:53 -0800)]
Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep/waitqueues: Add better annotation
lockdep, bug: Exclude TAINT_OOT_MODULE from disabling lock debugging
lockdep: Print lock name in lockdep_init_error()
init/main.c: Execute lockdep_init() as early as possible
lockdep, kmemcheck: Annotate ->lock in lockdep_init_map()
lockdep, rtmutex, bug: Show taint flags on error
lockdep, bug: Exclude TAINT_FIRMWARE_WORKAROUND from disabling lockdep
lockdep: Always try to set ->class_cache in register_lock_class() lockdep_init_map()
Linus Torvalds [Fri, 6 Jan 2012 15:53:34 +0000 (07:53 -0800)]
Merge branch 'core-debugobjects-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-debugobjects-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Use debugobjects to catch deletion of uninitialized timers
timer: Setup uninitialized timer with a stub callback
debugobjects: Extend to assert that an object is initialized
debugobjects: Be smarter about static objects
Sumit Semwal [Mon, 26 Dec 2011 09:23:17 +0000 (14:53 +0530)]
dma-buf: mark EXPERIMENTAL for 1st release.
Mark dma-buf buffer sharing API as EXPERIMENTAL for first release.
We will remove this in later versions, once it gets smoothed out
and has more users.
Sumit Semwal [Mon, 26 Dec 2011 09:23:15 +0000 (14:53 +0530)]
dma-buf: Introduce dma buffer sharing mechanism
This is the first step in defining a dma buffer sharing mechanism.
A new buffer object dma_buf is added, with operations and API to allow easy
sharing of this buffer object across devices.
The framework allows:
- creation of a buffer object, its association with a file pointer, and
associated allocator-defined operations on that buffer. This operation is
called the 'export' operation.
- different devices to 'attach' themselves to this exported buffer object, to
facilitate backing storage negotiation, using dma_buf_attach() API.
- the exported buffer object to be shared with the other entity by asking for
its 'file-descriptor (fd)', and sharing the fd across.
- a received fd to get the buffer object back, where it can be accessed using
the associated exporter-defined operations.
- the exporter and user to share the scatterlist associated with this buffer
object using map_dma_buf and unmap_dma_buf operations.
Atleast one 'attach()' call is required to be made prior to calling the
map_dma_buf() operation.
Couple of building blocks in map_dma_buf() are added to ease introduction
of sync'ing across exporter and users, and late allocation by the exporter.
For this first version, this framework will work with certain conditions:
- *ONLY* exporter will be allowed to mmap to userspace (outside of this
framework - mmap is not a buffer object operation),
- currently, *ONLY* users that do not need CPU access to the buffer are
allowed.
More details are there in the documentation patch.
This is based on design suggestions from many people at the mini-summits[1],
most notably from Arnd Bergmann <arnd@arndb.de>, Rob Clark <rob@ti.com> and
Daniel Vetter <daniel@ffwll.ch>.
The implementation is inspired from proof-of-concept patch-set from
Tomasz Stanislawski <t.stanislaws@samsung.com>, who demonstrated buffer sharing
between two v4l2 devices. [2]
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Sumit Semwal <sumit.semwal@ti.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Dave Airlie <airlied@redhat.com> Reviewed-and-Tested-by: Rob Clark <rob.clark@linaro.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 5 Jan 2012 23:40:12 +0000 (15:40 -0800)]
vfs: fix up ENOIOCTLCMD error handling
We're doing some odd things there, which already messes up various users
(see the net/socket.c code that this removes), and it was going to add
yet more crud to the block layer because of the incorrect error code
translation.
ENOIOCTLCMD is not an error return that should be returned to user mode
from the "ioctl()" system call, but it should *not* be translated as
EINVAL ("Invalid argument"). It should be translated as ENOTTY
("Inappropriate ioctl for device").
That EINVAL confusion has apparently so permeated some code that the
block layer actually checks for it, which is sad. We continue to do so
for now, but add a big comment about how wrong that is, and we should
remove it entirely eventually. In the meantime, this tries to keep the
changes localized to just the EINVAL -> ENOTTY fix, and removing code
that makes it harder to do the right thing.
Ian Campbell [Thu, 5 Jan 2012 07:13:39 +0000 (07:13 +0000)]
net: pack skb_shared_info more efficiently
nr_frags can be 8 bits since 256 is plenty of fragments. This allows it to be
packed with tx_flags.
Also by moving ip6_frag_id and dataref (both 4 bytes) next to each other we can
avoid a hole between ip6_frag_id and frag_list on 64 bit systems.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 5 Jan 2012 02:25:16 +0000 (02:25 +0000)]
net_sched: red: split red_parms into parms and vars
This patch splits the red_parms structure into two components.
One holding the RED 'constant' parameters, and one containing the
variables.
This permits a size reduction of GRED qdisc, and is a preliminary step
to add an optional RED unit to SFQ.
SFQRED will have a single red_parms structure shared by all flows, and a
private red_vars per flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Dave Taht <dave.taht@gmail.com> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Jan 2012 14:18:38 +0000 (14:18 +0000)]
net_sched: sfq: extend limits
SFQ as implemented in Linux is very limited, with at most 127 flows
and limit of 127 packets. [ So if 127 flows are active, we have one
packet per flow ]
This patch brings to SFQ following features to cope with modern needs.
- Ability to specify a smaller per flow limit of inflight packets.
(default value being at 127 packets)
- Ability to have up to 65408 active flows (instead of 127)
- Ability to have head drops instead of tail drops
(to drop old packets from a flow)
Example of use : No more than 20 packets per flow, max 8000 flows, max
20000 packets in SFQ qdisc, hash table of 65536 slots.
2 bytes per hash table entry (instead of previous 1 byte/entry)
32 bytes per flow on 64bit arches, instead of 384 for QFQ, so much
better cache hit ratio.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Dave Taht <dave.taht@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 4 Jan 2012 12:12:28 +0000 (12:12 +0000)]
cnic: Improve error recovery on bnx2x devices
When a bnx2x device encounters parity errors, it will not respond to all
SPQ messages. As a result, the shutdown sequence before reset can take
a long time as the ulp drivers (bnx2i/bnx2fc) have to wait for timeout
of all such messages.
To improve this scenario, when bnx2x returns error on the SPQ, we'll send
an immediate response to the ulp drivers to avoid such lengthy timeouts.
Adjust the return code of relevant functions to return error only if
the message cannot be sent on the SPQ so that we'll generate an error
completion to the ulp drivers.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Not now, but it looks you are correct. q->qdisc is NULL until another
additional qdisc is attached (beside tfifo). See 50612537e9ab2969312.
The following patch should work.
From: Hagen Paul Pfeifer <hagen@jauu.net>
netem: catch NULL pointer by updating the real qdisc statistic
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a several sparse warnings.
* the __iomem tag was being used incorrectly (needs to be a prefix)
* several variables should have been static since local to one file
* the firmware was not being forwared declared
and was const one place and not the other
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All tables of function pointers should be const to make hacks
more difficult. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All tables of function pointers should be const to make hacks
more difficult. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Waychison [Wed, 4 Jan 2012 12:52:32 +0000 (12:52 +0000)]
virtio_net: Pass gfp flags when allocating rx buffers.
Currently, the refill path for RX buffers will always allocate the
buffers as GFP_ATOMIC, even if we are in process context. This will
fail to apply memory pressure as the worker thread will not contribute
to the freeing of memory.
Fix this by changing add_recvbuf_small to use the gfp variant allocator,
__netdev_alloc_skb_ip_align().
Signed-off-by: Mike Waychison <mikew@google.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Neerav Parikh [Wed, 4 Jan 2012 20:23:40 +0000 (20:23 +0000)]
ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call
This patch implements support for ndo_get_fcoe_hbainfo()
call in the ixgbe driver.
This function will be called by the FCoE protocol stack to
obtain device specific information from the underlying
device configured to do FCoE.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neerav Parikh [Wed, 4 Jan 2012 20:23:39 +0000 (20:23 +0000)]
netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call
This adds a new ndo_get_fcoe_hbainfo() call in
net_device_ops for FCoE protocol stack.
If supported by the underlying device, the FCoE protocol
stack will call this to get device specific information
from the underlying device.
This information will then be utilized by the FCoE protocol
stack to register Fiber Channel HBA attributes with the
Fiber Channel Management Service via Fabric Device
Management Interface (FDMI) as per the T11 FC-GS
specification.
Changes in v2:
- As per comments from David Miller aligning the parameters
of the ndo_get_fcoe_hbainfo()
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Koki Sanagi [Wed, 4 Jan 2012 20:23:38 +0000 (20:23 +0000)]
igb: reset PHY after recovering from PHY power down
According to 82576_Datasheet.pdf, PHY setting is lost after PHY power down.
So resetting PHY is needed when recovering from PHY power down to set a default
setting to PHY register.
Owing to this lack, NIC doesn't link up in some rare situation.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yan, Zheng [Wed, 4 Jan 2012 20:23:37 +0000 (20:23 +0000)]
igb: add basic runtime PM support
Use the runtime power management framework to add basic runtime PM support
to the igb driver. Namely, make the driver suspend the device when the link
is off and set it up for generating a wakeup event after the link has been
detected again. This feature is disabled by default.
Based on e1000e's runtime PM code.
Changes since v1:
Don't suspend the device when shutting down the interface.
Avoid race between runtime suspending and ethtool operations.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Jan 2012 20:23:36 +0000 (20:23 +0000)]
igb: Add support for byte queue limits.
This adds support for byte queue limits (BQL)
Since this driver collects bytes count in 'bytecount' field, use it also
in igb_tx_map()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A global variable is currently used to hold the virtual address of the
CE4100 MDIO base register address. Store the address in the e1000_hw
structure and update macros accordingly.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove
We are not unmapping ce4100_gbe_mdio_base_virt in exit path in case
we are running on a CE4100 adapter, fix that.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Steven Rostedt, e1000 has a lockdep splat added
during the recent merge window. The issue is that
cancel_delayed_work is called while holding our private mutex.
There is no reason that I can see to hold the mutex during pci
shutdown, it was more just paranoia that I put the mutex_lock
around the call to e1000_down.
In a quick survey lots of drivers handle locking differently when
being called by the pci layer. The assumption here is that we
don't need the mutexes' protection in this function because
the driver could not be unloaded while in the shutdown handler
which is only called at reboot or poweroff.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Steven Rostedt <rostedt@goodmis.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add error handling so if lm75_update_device fails
an error is returned when reading the value through sysfs.
This is closely modeled after the way this is handled in ltc4261.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
projects / mirror_ubuntu-disco-kernel.git / log