Ivan Khoronzhuk [Mon, 8 Jul 2019 21:34:32 +0000 (00:34 +0300)]
net: ethernet: ti: cpsw: add XDP support
Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.
Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.
XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.
In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.
Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Mon, 8 Jul 2019 21:34:31 +0000 (00:34 +0300)]
net: ethernet: ti: cpsw_ethtool: allow res split while down
That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Mon, 8 Jul 2019 21:34:30 +0000 (00:34 +0300)]
net: ethernet: ti: davinci_cpdma: allow desc split while down
That's possible to set ring params while interfaces are down. When
interface gets up it uses number of descs to fill rx queue and on
later on changes to create rx pools. Usually, this resplit can happen
after phy is up, but it can be needed before this, so allow it to
happen while setting number of rx descs, when interfaces are down.
Also, if no dependency on intf state, move it to cpdma layer, where
it should be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
In case if dma mapped packet needs to be sent, like with XDP
page pool, the "mapped" submit can be used. This patch adds dma
mapped submit based on regular one.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Mon, 8 Jul 2019 21:34:28 +0000 (00:34 +0300)]
net: core: page_pool: add user refcnt and reintroduce page_pool_destroy
Jesper recently removed page_pool_destroy() (from driver invocation)
and moved shutdown and free of page_pool into xdp_rxq_info_unreg(),
in-order to handle in-flight packets/pages. This created an asymmetry
in drivers create/destroy pairs.
This patch reintroduce page_pool_destroy and add page_pool user
refcnt. This serves the purpose to simplify drivers error handling as
driver now drivers always calls page_pool_destroy() and don't need to
track if xdp_rxq_info_reg_mem_model() was unsuccessful.
This could be used for a special cases where a single RX-queue (with a
single page_pool) provides packets for two net_device'es, and thus
needs to register the same page_pool twice with two xdp_rxq_info
structures.
This patch is primarily to ease API usage for drivers. The recently
merged netsec driver, actually have a bug in this area, which is
solved by this API change.
This patch is a modified version of Ivan Khoronzhuk's original patch.
Link: https://lore.kernel.org/netdev/20190625175948.24771-2-ivan.khoronzhuk@linaro.org/ Fixes: 5c67bf0ec4d0 ("net: netsec: Use page_pool API") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF is disabled, we get a harmless warning about the
newly added variable:
drivers/net/ethernet/cadence/macb_main.c:48:39: error: 'mgmt' defined but not used [-Werror=unused-variable]
static struct sifive_fu540_macb_mgmt *mgmt;
Move the variable closer to its use inside of the #ifdef.
Fixes: c218ad559020 ("macb: Add support for SiFive FU540-C000") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Change the preprocessor #if to regular if() to avoid this.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Mon, 8 Jul 2019 11:07:11 +0000 (12:07 +0100)]
sfc: Remove 'PCIE error reporting unavailable'
This is only at notice level but it was pointed out that no other driver
does this.
Also there is no action the user can take as it is really a property of
the server.
Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds firmware version query in ethtool -i.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Main goal of this patch series is to add support for CPU attached parallel
bus in Vitesse VSC73xx switches. Existing driver supports only SPI mode.
Second change is needed for devices in unmanaged state.
V3:
- fix commit messages and descriptions about memory-mapped I/O mode
V2:
- drop changes in compatible strings
- make changes less invasive
- drop mutex in platform part and move mutex from core to spi part
- fix indentation
- fix devm_ioremap_resource result check
- add cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: vsc73xx: Assert reset if iCPU is enabled
Driver allow to use devices with disabled iCPU only.
Some devices have pre-initialised iCPU by bootloader.
That state make switch unmanaged. This patch force reset
if device is in unmanaged state. In the result chip lost
internal firmware from RAM and it can be managed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add platform part of vsc73xx driver.
It allows to use chip connected to a parallel memory bus and work in
memory-mapped I/O mode. (aka PI bus in chip manual)
By default device is working in big endian mode.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. But Vitesse chip support also parallel interface.
This patch split driver into two parts: core and spi. It is required
for add support to another managing interface.
Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 1 Jul 2019 16:54:55 +0000 (00:54 +0800)]
tipc: use rcu dereference functions properly
For these places are protected by rcu_read_lock, we change from
rcu_dereference_rtnl to rcu_dereference, as there is no need to
check if rtnl lock is held.
For these places are protected by rtnl_lock, we change from
rcu_dereference_rtnl to rtnl_dereference/rcu_dereference_protected,
as no extra memory barriers are needed under rtnl_lock() which also
protects tn->bearer_list[] and dev->tipc_ptr/b->media_ptr updating.
rcu_dereference_rtnl will be only used in the places where it could
be under rcu_read_lock or rtnl_lock.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the main bluetooth-next pull request for 5.3:
- Added support for new devices from Qualcomm, Realtek and Broadcom and
MediaTek
- Various fixes to 6LoWPAN
- Fix L2CAP PSM namespace separation for LE & BR/EDR
- Fix behavior with Microsoft Surface Precision Mouse
- Added support for LE Ping feature
- Fix L2CAP Disconnect response handling if received in wrong state
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BLE based 6LoWPAN networks are highly constrained in bandwidth.
Do not take a short-cut, always check if the destination address is
known to belong to a peer.
As a side-effect this also removes any behavioral differences between
one, and two or more connected peers.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: 6lowpan: check neighbour table for SLAAC
Like any IPv6 capable device, 6LNs can have multiple addresses assigned
using SLAAC and made known through neighbour advertisements.
After checking the destination address against all peers link-local
addresses, consult the neighbour cache for additional known addresses.
RFC7668 defines the scope of Neighbor Advertisements in Section 3.2.3:
1. "A Bluetooth LE 6LN MUST NOT register its link-local address"
2. "A Bluetooth LE 6LN MUST register its non-link-local addresses with
the 6LBR by sending Neighbor Solicitation (NS) messages ..."
Due to these constranits both the link-local addresses tracked in the
list of 6lowpan peers, and the neighbour cache have to be used when
identifying the 6lowpan peer for a destination address.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: 6lowpan: search for destination address in all peers
Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.
For one peer, no checks are performed to see if it is meant to receive
packets for a given address.
As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Szymon Janc [Tue, 18 Jun 2019 22:47:47 +0000 (00:47 +0200)]
Bluetooth: Add SMP workaround Microsoft Surface Precision Mouse bug
Microsoft Surface Precision Mouse provides bogus identity address when
pairing. It connects with Static Random address but provides Public
Address in SMP Identity Address Information PDU. Address has same
value but type is different. Workaround this by dropping IRK if ID
address discrepancy is detected.
csonsino [Wed, 12 Jun 2019 21:00:52 +0000 (15:00 -0600)]
Bluetooth: validate BLE connection interval updates
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.
As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Matias Karhumaa [Tue, 21 May 2019 10:07:22 +0000 (13:07 +0300)]
Bluetooth: Check state in l2cap_disconnect_rsp
Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.
Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.
Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499
L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397
L2CAP: Connection Request (0x02) ident 27 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441
L2CAP: Connection Response (0x03) ident 27 len 8
Destination CID: 65
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073
L2CAP: Connection Request (0x02) ident 12 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371
L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804
L2CAP: Connection Response (0x03) ident 12 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Fix is to check that channel is in state BT_DISCONN before deleting the
channel.
This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com> Reported-by: Ari Timonen <ari.timonen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dan Carpenter [Thu, 16 May 2019 18:24:00 +0000 (21:24 +0300)]
Bluetooth: hidp: NUL terminate a string in the compat ioctl
This change is similar to commit a1616a5ac99e ("Bluetooth: hidp: fix
buffer overflow") but for the compat ioctl. We take a string from the
user and forgot to ensure that it's NUL terminated.
I have also changed the strncpy() in to strscpy() in hidp_setup_hid().
The difference is the strncpy() doesn't necessarily NUL terminate the
destination string. Either change would fix the problem but it's nice
to take a belt and suspenders approach and do both.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Sun, 2 Jun 2019 01:04:17 +0000 (09:04 +0800)]
Bluetooth: btmtkuart: add an implementation for clock osc property
Some board requires explicitily control external osscilator via GPIO.
So, add an implementation of a clock property for an external oscillator
to the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Sun, 2 Jun 2019 01:04:16 +0000 (09:04 +0800)]
Bluetooth: btmtkuart: add an implementation for boot-gpios property
Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so the driver
adds additional boot-gpios to let the MT766[3,8]U can enter the proper boot
mode by gpiod for such platform.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Sun, 2 Jun 2019 01:04:14 +0000 (09:04 +0800)]
dt-bindings: net: bluetooth: add boot-gpios property to UART-based device
Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so adding an
additional boot-gpios property for such platform allows them to bring up
the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rocky Liao [Thu, 6 Jun 2019 09:40:30 +0000 (17:40 +0800)]
Bluetooth: hci_qca: Load customized NVM based on the device property
QCA BTSOC NVM is a customized firmware file and different vendors may
want to have different BTSOC configuration (e.g. Configure SCO over PCM
or I2S, Setting Tx power, etc.) via this file. This patch will allow
vendors to download different NVM firmware file by reading a device
property "firmware-name".
Sascha Hauer [Fri, 14 Jun 2019 07:23:51 +0000 (09:23 +0200)]
Bluetooth: hci_mrvl: Add serdev support
This adds serdev support to the Marvell hci uart driver. Only basic
serdev support, none of the fancier features like regulator or enable
GPIO support is added for now.
Sascha Hauer [Fri, 14 Jun 2019 07:23:50 +0000 (09:23 +0200)]
Bluetooth: hci_mrvl: Wait for final ack before switching baudrate
For the Marvell HCI UART we have to upload two firmware files. The first
one is only for switching the baudrate of the device to a higher
baudrate. After the baudrate switching firmware has been uploaded the
device waits for a final ack (0x5a) before actually switching the
baudrate. To send this final ack with the old baudrate give the hci
ldisc workqueue a chance to run before switching the baudrate. Without
this the final ack will never be received by the device and firmware
upload fails.
Sascha Hauer [Fri, 14 Jun 2019 07:23:49 +0000 (09:23 +0200)]
Bluetooth: hci_ldisc: Add function to wait for characters to be sent
The hci UART line discipline sends its characters in a workqueue. Some
devices like the Marvell Bluetooth chips need to make sure that all
queued characters are sent before switching the baudrate. This adds
a function to synchronize with the workqueue.
6lowpan: no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care if debugfs works or not, this trickles back a bit
so we can clean things up by making some functions return void instead
of an error value that is never going to fail.
This is caused by a vendor event that corresponds to an earlier command
to change the baudrate. The event is not processed in the context of the
baudrate change and is later interpreted as response to the firmware
download command (which is also a vendor command), but the driver detects
that the event doesn't have the expected amount of associated data.
More details:
For the WCN3990 the vendor command for a baudrate change isn't sent as
synchronous HCI command, because the controller sends the corresponding
vendor event with the new baudrate. The event is received and decoded
after the baudrate change of the host port.
Identify the 'unused' event when it is received and don't add it to
the queue of RX frames.
Bluetooth: btqca: inject command complete event during fw download
Latest qualcomm chips are not sending an command complete event for
every firmware packet sent to chip. They only respond with a vendor
specific event for the last firmware packet. This optimization will
decrease the BT ON time. Due to this we are seeing a timeout error
message logs on the console during firmware download. Now we are
injecting a command complete event once we receive an vendor specific
event for the last RAM firmware packet.
Fix some warnings and one error reported by checkpatch.pl:
- lines longer than 80 characters are wrapped
- empty lines inserted to separate variable declarations from the actual
code
- line break inserted after if (...)
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de> Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de> Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de> Cc: linux-kernel@i4.cs.fau.de Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jian-Hong Pan [Tue, 25 Jun 2019 08:30:51 +0000 (16:30 +0800)]
Bluetooth: btrtl: HCI reset on close for Realtek BT chip
Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly
after on-off several times. Bluetooth daemon sets BT mode failed when
this issue happens. Scanning must be active while turning off for this
bug to be hit.
bluetoothd[1576]: Failed to set mode: Failed (0x03)
If BT is turned off, then turned on again, it works correctly again.
According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set
during probing. So, this patch makes Realtek's BT reset on close to fix
this issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429 Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extract the new function send_command_from_firmware from
download_firmware, which helps with the readability of the switch
statement. This way the code is less deeply nested and also no longer
exceeds the 80 character limit.
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de> Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de> Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: hci_ll: set operational frequency earlier
Uploading the firmware needs quite a few seconds if done at 115200 kbps. So set
the operational frequency, usually 3 MHz, before uploading the firmware.
I have successfully tested this with a wl1837mod.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Peter Robinson [Sun, 30 Jun 2019 22:14:08 +0000 (23:14 +0100)]
Bluetooth: btsdio: Do not bind to non-removable BCM4356
BCM4356 devices soldered onto the PCB (non-removable) use an UART
connection for bluetooth, such as the Rock960, but it also advertise
btsdio support as a sdio function.
David S. Miller [Fri, 5 Jul 2019 23:29:20 +0000 (16:29 -0700)]
Merge branch 'mlx5-TLS-TX-HW-offload-support'
Tariq Toukan says:
====================
mlx5 TLS TX HW offload support
This series from Eran and me, adds TLS TX HW offload support to
the mlx5 driver.
This offloads the kTLS encryption process from kernel to the
Mellanox NIC, saving CPU cycles and improving utilization.
Upon a new TLS connection request, driver is responsible to create
a dedicated HW context and configure it according to the crypto info,
so HW can do the encryption itself.
When the HW context gets out-of-sync (i.e. due to packets retransmission),
driver is responsible for the re-sync process.
This is done by posting special resync descriptors to the HW.
Feature is supported on Mellanox Connect-X 6DX, and newer.
Series was tested on SimX simulator.
Series generated against net-next commit [1], with Saeed's request pulled [2]:
Changes from last pull request:
Fixed comments from Jakub:
Patch 4:
- Replace zero memset with a call to memzero_explicit().
Patch 11:
- Fix stats counters names.
- Drop TLS SKB with non-matching netdev.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmit side kernel-TLS acceleration.
Offload the crypto encryption to HW.
Per TLS connection:
- Use a separate TIS to maintain the HW context.
- Use a separate encryption key.
- Maintain static and progress HW contexts by posting the proper
WQEs at creation time, or upon resync.
- Use a special DUMP opcode to replay the previous frags and sync
the HW context.
To make sure the SQ is able to serve an xmit request, increase
SQ stop room to cover:
- static params WQE,
- progress params WQE, and
- resync DUMP per frag.
Currently supporting TLS 1.2, and key size 128bit.
Tested over SimX simulator.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Introduce a fenced NOP WQE posting function
Similar to the existing mlx5e_post_nop(), but marks a fence
in the WQE control segment.
Added as a separate new function to not hurt the performance
of the common case.
To be used in a downstream patch of the series.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Let the EN TIS creation function (mlx5e_create_tis) be responsible
for applying common mdev related fields.
Other specific fields must be set by the caller and passed within
the inbox.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use an SQ field for stop_room, and use the larger value only if TLS
is supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Fri, 5 Jul 2019 15:30:18 +0000 (18:30 +0300)]
net/mlx5e: Tx, Don't implicitly assume SKB-less wqe has one WQEBB
When polling a CQE of an SKB-less WQE, don't assume it consumed only
one WQEBB. Use wi->num_wqebbs directly instead.
In the downstream patch, SKB-less WQEs might have more the one WQEBB,
thus this change is needed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Tx, Make SQ WQE fetch function type generic
Change mlx5e_sq_fetch_wqe to be agnostic to the Work Queue
Element (WQE) type.
Before this patch, it was specific for struct mlx5e_tx_wqe.
In order to allow the change, the function now returns the
generic void pointer, and gets the WQE size to do the zero
memset.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When ctrl->tisn field exists, this indicates an operation (HW offload)
on the TCP payload.
For such WQEs, inline the headers up to L4.
This is in preparation for kTLS HW offload support, added in
a downstream patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Move helper functions to a new txrx datapath header
Take datapath helper functions to a new header file en/txrx.h.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Accel, Add core TLS support for the Connect-X family
Add support for the new TLS implementation of the Connect-X family.
Introduce a new compilation flag MLX5_TLS for it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Add crypto library to support create/destroy encryption key
Encryption key create / destroy is done via
CREATE_GENERAL_OBJECT / DESTROY_GENERAL_OBJECT commands.
To be used in downstream patches by TLS API wrappers, to configure
the TIS context with the encryption key.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Kconfig, Better organize compilation flags
Always contain all acceleration functions declarations in
'accel' files, independent to the flags setting.
For this, introduce new flags CONFIG_FPGA_{IPSEC/TLS} and use stubs
where needed.
This obsoletes the need for stubs in 'fpga' files. Remove them.
Also use the new flags in Makefile, to decide whether to compile
TLS-specific or IPSEC-specific objects, or not.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Accel, Expose accel wrapper for IPsec FPGA function
Do not directly call fpga version of IPsec function from main.c.
Wrap it by an accel version, and call the wrapper.
This will allow deprecating the FPGA IPsec stubs in downstream
patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: oss-drivers@netronome.com Cc: netdev@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netsec: Sync dma for device on buffer allocation
Quoting Arnd,
We have to do a sync_single_for_device /somewhere/ before the
buffer is given to the device. On a non-cache-coherent machine with
a write-back cache, there may be dirty cache lines that get written back
after the device DMA's data into it (e.g. from a previous memset
from before the buffer got freed), so you absolutely need to flush any
dirty cache lines on it first.
Since the coherency is configurable in this device make sure we cover
all configurations by explicitly syncing the allocated buffer for the
device before refilling it's descriptors
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 4 Jul 2019 14:04:28 +0000 (22:04 +0800)]
net: hns3: set maximum length to resp_data_len for exceptional case
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE,
the memcpy will cause out of memory. So this patch just set
resp_data_len to the maximum length for this case.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Thu, 4 Jul 2019 14:04:27 +0000 (22:04 +0800)]
net: hns3: bitwise operator should use unsigned type
There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 4 Jul 2019 14:04:26 +0000 (22:04 +0800)]
net: hns3: add default value for tc_size and tc_offset
This patch adds default value for tc_size and tc_offset, or it may
get random value and used later.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 4 Jul 2019 14:04:25 +0000 (22:04 +0800)]
net: hns3: check msg_data before memcpy in hclgevf_send_mbx_msg
The value of msg_data may be NULL in some cases, which will cause
errors reported by some compiler.
So this patch adds a check to fix it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 4 Jul 2019 14:04:24 +0000 (22:04 +0800)]
net: hns3: set default value for param "type" in hclgevf_bind_ring_to_vector
The value of param type is always not changed in
hclgevf_bind_ring_to_vector, move the assignment to
front of "for {}" can reduce the redundant assignment.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 4 Jul 2019 14:04:23 +0000 (22:04 +0800)]
net: hns3: add all IMP return code
Currently, the HNS3 driver just defines part of IMP return code,
This patch supplements all the remaining IMP return code, and adds
a function to convert this code to the error number.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver queries the media port information, and
updates the port capability periodically. But it sets an error
mac->speed_type value, which stops update port capability.
Fixes: 88d10bd6f730 ("net: hns3: add support for multiple media type") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: fix flow control configure issue for fibre port
Flow control autoneg is unsupported for fibre port. It takes no
effect for flow control when restart autoneg. This patch fixes
it, return -EOPNOTSUPP when user tries to enable flow control
autoneg.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: enable broadcast promisc mode when initializing VF
For revision 0x20, the broadcast promisc is enabled by firmware,
it's unnecessary to enable it when initializing VF.
For revision 0x21, it's necessary to enable broadcast promisc mode
when initializing or re-initializing VF, otherwise, it will be
unable to send and receive promisc packets.
Fixes: f01f5559cac8 ("net: hns3: don't allow vf to enable promisc mode") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get more accurate hardware time stamping in Spectrum-1, the
driver needs to apply a shaper on the port for speeds lower than 40Gbps.
This shaper is called a PTP shaper and it is applied on hierarchy 0,
which is the port hierarchy. This shaper may affect the shaper rates of
all hierarchies.
This patchset adds the ability to enable or disable the PTP shaper on
the port in two scenarios:
1. When the user wants to enable/disable the hardware time stamping
2. When the port is brought up or down (including port speed change)
Patch #1 adds the QEEC.ptps field that is used for enabling or disabling
the PTP shaper on a port.
Patch #2 adds a note about disabling the PTP shaper when calling to
mlxsw_sp_port_ets_maxrate_set().
Patch #3 adds the QPSC register that is responsible for configuring the
PTP shaper parameters per speed.
Patch #4 sets the PTP shaper parameters during the ptp_init().
Patch #5 adds new operation for getting the port's speed.
Patch #6 enables/disables the PTP shaper when turning on or off the
hardware time stamping.
Patch #7 enables/disables the PTP shaper when the port's status has
changed (including port speed change).
Patch #8 applies the PTP shaper enable/disable logic by filling the PTP
shaper parameters array.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_ptp: Enable/disable PTP shaper on a port when getting HWTSTAMP on/off
In order to get more accurate hardware time stamping, the driver needs to
enable PTP shaper on the port, for speeds lower than 40 Gbps.
Enable the PTP shaper on the port when the user turns on the hardware
time stamping, and disable it when the user turns off the hardware time
stamping.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_ptp: Set the PTP shaper parameters
Set the PTP shaper parameters during the ptp_init(). For different
speeds, there are different parameters.
When the port's speed changes and PTP shaper is enabled, the firmware
changes the ETS shaper values according to the PTP shaper parameters for
this new speed.
The PTP shaper parameters array is left empty for now, will be filled in
a follow-up patch.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: socionext: remove set but not used variable 'pkts'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_clean_tx_dring':
drivers/net/ethernet/socionext/netsec.c:637:15: warning:
variable 'pkts' set but not used [-Wunused-but-set-variable]
It is not used since commit ba2b232108d3 ("net: netsec: add XDP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log