As noted in commit 28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If there is an entry at INT_MAX then idr_for_each_entry() will increment
id after handling it. This is undefined behaviour, and is caught by
UBSAN. Adding 1U to id forces the operation to be carried out as an
unsigned addition which (when assigned to id) will result in INT_MIN.
Since there is never an entry stored at INT_MIN, idr_get_next() will
return NULL, ending the loop as expected.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543 Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3eddb4 ("net: fec: add missed clk_disable_unprepare in remove") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If we pass 0 as bios_args.datasize argument then (Local5 * 0x08)
is 0 which results in these errors:
[ 71.973305] ACPI BIOS Error (bug): Attempt to CreateField of length zero (20190816/dsopcode-133)
[ 71.973332] ACPI Error: Aborting method \HWMC due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
[ 71.973413] ACPI Error: Aborting method \_SB.WMID.WMAA due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
And in our HPWMI_WIRELESS2_QUERY calls always failing. for read commands
like HPWMI_WIRELESS2_QUERY the DSZI value is not used / checked, except for
read commands where extra input is needed to specify exactly what to read.
So for HPWMI_WIRELESS2_QUERY we can safely pass the size of the expected
output as insize to hp_wmi_perform_query(), as we are already doing for all
other HPWMI_READ commands we send. Doing so fixes these errors.
The HP WMI calls may take up to 128 bytes of data as input, and
the AML methods implementing the WMI calls, declare a couple of fields for
accessing input in different sizes, specifycally the HWMC method contains:
CreateField (Arg1, 0x80, 0x0400, D128)
Even though we do not use any of the WMI command-types which need a buffer
of this size, the APCI interpreter still tries to create it as it is
declared in generoc code at the top of the HWMC method which runs before
the code looks at which command-type is requested.
This results in many of these errors on many different HP laptop models:
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
configs is allocated by pinconf_generic_parse_dt_config(),
pinctrl_utils_add_map_configs() duplicates configs so it can and has to
be freed to prevent memory leaks.
No remove function implemented yet in the driver.
Without remove function, the pm_runtime implementation
complains when removing and probing again the driver.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Correct condition for the second hmac loop. Key must be only
set in the first loop. Initial condition was wrong,
HMAC_KEY flag was not properly checked.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Upstream commit 58e75155009c ("HID: core: move Usage Page concatenation
to Main item") adds support for Usage Page item after Usage ID items
(such as keyboards manufactured by Primax).
Usage Page concatenation in Main item works well for following report
descriptor patterns:
With Usage Page concatenation in Main item, parser recognizes all the
11 Usages as consumer keys, it is not the HID device's real intention.
This patch checks whether Usage Page is really defined after Usage ID
items by comparing usage page using status.
Usage Page concatenation on currently defined Usage Page will always
do in local parsing when Usage ID items encountered.
When Main item is parsing, concatenation will do again with last
defined Usage Page if this page has not been used in the previous
usages concatenation.
Signed-off-by: Candle Sun <candle.sun@unisoc.com> Signed-off-by: Nianfu Bai <nianfu.bai@unisoc.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Siarhei Vishniakou <svv@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
--> preemption (unrelated wakeup of some other higher prio task, e.g. timer)
switch_to(other_task)
return to user
sys_futex()
loop infinite as above
Just for the fun of it the futex exit cleanup could trigger the wakeup
itself before the task sets its futex state to DEAD.
To cure this, the handling of the exiting owner is changed so:
- A refcount is held on the task
- The task pointer is stored in a caller visible location
- The caller drops all locks (hash bucket, mmap_sem) and blocks
on task::futex_exit_mutex. When the mutex is acquired then
the exiting task has completed the cleanup and the state
is consistent and can be reevaluated.
This is not a pretty solution, but there is no choice other than returning
an error code to user space, which would break the state consistency
guarantee and open another can of problems including regressions.
For stable backports the preparatory commits ac31c7ff8624 .. ba31c1a48538
are required as well, but for anything older than 5.3.y the backports are
going to be provided when this hits mainline as the other dependencies for
those kernels are definitely not stable material.
Fixes: 778e9a9c3e71 ("pi-futex: fix exit races and locking problems") Reported-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Stable Team <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20191106224557.041676471@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The mutex will be used in subsequent changes to replace the busy looping of
a waiter when the futex owner is currently executing the exit cleanup to
prevent a potential live lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.845798895@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
exec() attempts to handle potentially held futexes gracefully by running
the futex exit handling code like exit() does.
The current implementation has no protection against concurrent incoming
waiters. The reason is that the futex state cannot be set to
FUTEX_STATE_DEAD after the cleanup because the task struct is still active
and just about to execute the new binary.
While its arguably buggy when a task holds a futex over exec(), for
consistency sake the state handling can at least cover the actual futex
exit cleanup section. This provides state consistency protection accross
the cleanup. As the futex state of the task becomes FUTEX_STATE_OK after the
cleanup has been finished, this cannot prevent subsequent attempts to
attach to the task in case that the cleanup was not successfull in mopping
up all leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.753355618@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Instead of relying on PF_EXITING use an explicit state for the futex exit
and set it in the futex exit function. This moves the smp barrier and the
lock/unlock serialization into the futex code.
As with the DEAD state this is restricted to the exit path as exec
continues to use the same task struct.
This allows to simplify that logic in a next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.539409004@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Setting task::futex_state in do_exit() is rather arbitrarily placed for no
reason. Move it into the futex code.
Note, this is only done for the exit cleanup as the exec cleanup cannot set
the state to FUTEX_STATE_DEAD because the task struct is still in active
use.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.439511191@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
To allow separate handling of the futex exit state in the futex exit code
for exit and exec, split futex_mm_release() into two functions and invoke
them from the corresponding exit/exec_mm_release() callsites.
Preparatory only, no functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.332094221@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The futex exit handling relies on PF_ flags. That's suboptimal as it
requires a smp_mb() and an ugly lock/unlock of the exiting tasks pi_lock in
the middle of do_exit() to enforce the observability of PF_EXITING in the
futex code.
Add a futex_state member to task_struct and convert the PF_EXITPIDONE logic
over to the new state. The PF_EXITING dependency will be cleaned up in a
later step.
This prepares for handling various futex exit issues later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.149449274@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The futex exit handling is #ifdeffed into mm_release() which is not pretty
to begin with. But upcoming changes to address futex exit races need to add
more functionality to this exit code.
Split it out into a function, move it into futex code and make the various
futex exit functions static.
Preparatory only and no functional change.
Folded build fix from Borislav.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.049705556@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Robust futexes utilize the robust_list mechanism to allow the kernel to
release futexes which are held when a task exits. The exit can be voluntary
or caused by a signal or fault. This prevents that waiters block forever.
The futex operations in user space store a pointer to the futex they are
either locking or unlocking in the op_pending member of the per task robust
list.
After a lock operation has succeeded the futex is queued in the robust list
linked list and the op_pending pointer is cleared.
After an unlock operation has succeeded the futex is removed from the
robust list linked list and the op_pending pointer is cleared.
The robust list exit code checks for the pending operation and any futex
which is queued in the linked list. It carefully checks whether the futex
value is the TID of the exiting task. If so, it sets the OWNER_DIED bit and
tries to wake up a potential waiter.
This is race free for the lock operation but unlock has two race scenarios
where waiters might not be woken up. These issues can be observed with
regular robust pthread mutexes. PI aware pthread mutexes are not affected.
(1) Unlocking task is killed after unlocking the futex value in user space
before being able to wake a waiter.
pthread_mutex_unlock()
|
V
atomic_exchange_rel (&mutex->__data.__lock, 0)
<------------------------killed
lll_futex_wake () |
|
|(__lock = 0)
|(enter kernel)
|
V
do_exit()
exit_mm()
mm_release()
exit_robust_list()
handle_futex_death()
|
|(__lock = 0)
|(uval = 0)
|
V
if ((uval & FUTEX_TID_MASK) != task_pid_vnr(curr))
return 0;
The sanity check which ensures that the user space futex is owned by
the exiting task prevents the wakeup of waiters which in consequence
block infinitely.
(2) Waiting task is killed after a wakeup and before it can acquire the
futex in user space.
OWNER WAITER
futex_wait()
pthread_mutex_unlock() |
| |
|(__lock = 0) |
| |
V |
futex_wake() ------------> wakeup()
|
|(return to userspace)
|(__lock = 0)
|
V
oldval = mutex->__data.__lock
<-----------------killed
atomic_compare_and_exchange_val_acq (&mutex->__data.__lock, |
id | assume_other_futex_waiters, 0) |
|
|
(enter kernel)|
|
V
do_exit()
|
|
V
handle_futex_death()
|
|(__lock = 0)
|(uval = 0)
|
V
if ((uval & FUTEX_TID_MASK) != task_pid_vnr(curr))
return 0;
The sanity check which ensures that the user space futex is owned
by the exiting task prevents the wakeup of waiters, which seems to
be correct as the exiting task does not own the futex value, but
the consequence is that other waiters wont be woken up and block
infinitely.
In both scenarios the following conditions are true:
- task->robust_list->list_op_pending != NULL
- user space futex value == 0
- Regular futex (not PI)
If these conditions are met then it is reasonably safe to wake up a
potential waiter in order to prevent the above problems.
As this might be a false positive it can cause spurious wakeups, but the
waiter side has to handle other types of unrelated wakeups, e.g. signals
gracefully anyway. So such a spurious wakeup will not affect the
correctness of these operations.
This workaround must not touch the user space futex value and cannot set
the OWNER_DIED bit because the lock value is 0, i.e. uncontended. Setting
OWNER_DIED in this case would result in inconsistent state and subsequently
in malfunction of the owner died handling in user space.
The rest of the user space state is still consistent as no other task can
observe the list_op_pending entry in the exiting tasks robust list.
The eventually woken up waiter will observe the uncontended lock value and
take it over.
[ tglx: Massaged changelog and comment. Made the return explicit and not
depend on the subsequent check and added constants to hand into
handle_futex_death() instead of plain numbers. Fixed a few coding
style issues. ]
Fixes: 0771dfefc9e5 ("[PATCH] lightweight robust futexes: core") Signed-off-by: Yang Tao <yang.tao172@zte.com.cn> Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1573010582-35297-1-git-send-email-wang.yi59@zte.com.cn Link: https://lkml.kernel.org/r/20191106224555.943191378@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We are going to share the compat_sys_futex() handler between 64-bit
architectures and 32-bit architectures that need to deal with both 32-bit
and 64-bit time_t, and this is easier if both entry points are in the
same file.
In fact, most other system call handlers do the same thing these days, so
let's follow the trend here and merge all of futex_compat.c into futex.c.
In the process, a few minor changes have to be done to make sure everything
still makes sense: handle_futex_death() and futex_cmpxchg_enabled() become
local symbol, and the compat version of the fetch_robust_entry() function
gets renamed to compat_fetch_robust_entry() to avoid a symbol clash.
This is intended as a purely cosmetic patch, no behavior should
change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The "params->size" is defined as "u64".
And "info->sector_size" and "info->n_sectors" are defined as
unsigned int and u16.
Thus, u64 data might have strange data(loss data) if the result
overflows an unsigned int.
This patch casts "info->sector_size" to an u64.
Signed-off-by: huijin.park <huijin.park@samsung.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Wen Yang <yellowriver2010@hotmail.com> Suggested-by: Boris Brezillon <bbrezillon@kernel.org> Reviewed-by: Boris Brezillon <bbrezillon@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Tudor Ambarus <tudor.ambarus@microchip.com> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: linux-mtd@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The subns increment register has 24 bits as follows:
RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0]
Fix the same in the driver and increase sub ns resolution to the
best capable, 24 bits. This should be the case on all GEM versions
that this PTP driver supports.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It's possible to specify a non-zero s_want_extra_isize via debugging
option, and this can cause bad things(tm) to happen when using a file
system with an inode size of 128 bytes.
Add better checking when the file system is mounted, as well as when
we are actually doing the trying to do the inode expansion.
When a classful qdisc's child qdisc has set the flag
TCQ_F_CPUSTATS (pfifo_fast for example), the child qdisc's
cpu_bstats should be passed to gnet_stats_copy_basic(),
but many classful qdisc didn't do that. As a result,
`tc -s class show dev DEV` always return 0 for bytes and
packets in this case.
Pass the child qdisc's cpu_bstats to gnet_stats_copy_basic()
to fix this issue.
The qstats also has this problem, but it has been fixed
in 5dd431b6b9 ("net: sched: introduce and use qstats read...")
and bstats still remains buggy.
Fixes: 22e0f8b9322c ("net: sched: make bstats per cpu and estimator RCU safe") Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch is to fix a data-race reported by syzbot:
BUG: KCSAN: data-race in sctp_assoc_migrate / sctp_hash_obj
write to 0xffff8880b67c0020 of 8 bytes by task 18908 on cpu 1:
sctp_assoc_migrate+0x1a6/0x290 net/sctp/associola.c:1091
sctp_sock_migrate+0x8aa/0x9b0 net/sctp/socket.c:9465
sctp_accept+0x3c8/0x470 net/sctp/socket.c:4916
inet_accept+0x7f/0x360 net/ipv4/af_inet.c:734
__sys_accept4+0x224/0x430 net/socket.c:1754
__do_sys_accept net/socket.c:1795 [inline]
__se_sys_accept net/socket.c:1792 [inline]
__x64_sys_accept+0x4e/0x60 net/socket.c:1792
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b67c0020 of 8 bytes by task 12003 on cpu 0:
sctp_hash_obj+0x4f/0x2d0 net/sctp/input.c:894
rht_key_get_hash include/linux/rhashtable.h:133 [inline]
rht_key_hashfn include/linux/rhashtable.h:159 [inline]
rht_head_hashfn include/linux/rhashtable.h:174 [inline]
head_hashfn lib/rhashtable.c:41 [inline]
rhashtable_rehash_one lib/rhashtable.c:245 [inline]
rhashtable_rehash_chain lib/rhashtable.c:276 [inline]
rhashtable_rehash_table lib/rhashtable.c:316 [inline]
rht_deferred_worker+0x468/0xab0 lib/rhashtable.c:420
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
It was caused by rhashtable access asoc->base.sk when sctp_assoc_migrate
is changing its value. However, what rhashtable wants is netns from asoc
base.sk, and for an asoc, its netns won't change once set. So we can
simply fix it by caching netns since created.
Fixes: d6c0256a60e6 ("sctp: add the rhashtable apis for sctp global transport hashtable") Reported-by: syzbot+e3b35fe7918ff0ee474e@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit 4f07b80c9733 ("tipc: check msg->req data len in
tipc_nl_compat_bearer_disable") the same patch code was copied into
routines: tipc_nl_compat_bearer_disable(),
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
The two link routine occurrences should have been modified to check
the maximum link name length and not bearer name length.
Fixes: 4f07b80c9733 ("tipc: check msg->reg data len in tipc_nl_compat_bearer_disable") Signed-off-by: John Rutherford <john.rutherford@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If we can't build the flow del notification, we can simply delete
the flow, no need to crash the kernel. Still keep a WARN_ON to
preserve debuggability.
Note: the BUG_ON() predates the Fixes tag, but this change
can be applied only after the mentioned commit.
v1 -> v2:
- do not leak an skb on error
Fixes: aed067783e50 ("openvswitch: Minimize ovs_flow_cmd_del critical section.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
All the callers of ovs_flow_cmd_build_info() already deal with
error return code correctly, so we can handle the error condition
in a more gracefull way. Still dump a warning to preserve
debuggability.
v1 -> v2:
- clarify the commit message
- clean the skb and report the error (DaveM)
Fixes: ccb1352e76cf ("net: Add Open vSwitch kernel components.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Slip_open doesn't clean-up device which registration failed from the
slip_devs device list. On next open after failure this list is iterated
and freed device is accessed. Fix this by calling sl_free_netdev in error
path.
When user-space sets the OVS_UFID_F_OMIT_* flags, and the relevant
flow has no UFID, we can exceed the computed size, as
ovs_nla_put_identifier() will always dump an OVS_FLOW_ATTR_KEY
attribute.
Take the above in account when computing the flow command message
size.
Fixes: 74ed7ab9264c ("openvswitch: Add support for unique flow IDs.") Reported-by: Qi Jun Ding <qding@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to calculate the skb size correctly otherwise we risk triggering
skb_over_panic[1]. The issue is that data_len is added to the skb in a
nl attribute, but we don't account for its header size (nlattr 4 bytes)
and alignment. We account for it when calculating the total size in
the > PSAMPLE_MAX_PACKET_SIZE comparison correctly, but not when
allocating after that. The fix is simple - use nla_total_size() for
data_len when allocating.
To reproduce:
$ tc qdisc add dev eth1 clsact
$ tc filter add dev eth1 egress matchall action sample rate 1 group 1 trunc 129
$ mausezahn eth1 -b bcast -a rand -c 1 -p 129
< skb_over_panic BUG(), tail is 4 bytes past skb->end >
While enqueueing a broadcast skb to port->bc_queue, schedule_work()
is called to add port->bc_work, which processes the skbs in
bc_queue, to "events" work queue. If port->bc_queue is full, the
skb will be discarded and schedule_work(&port->bc_work) won't be
called. However, if port->bc_queue is full and port->bc_work is not
running or pending, port->bc_queue will keep full and schedule_work()
won't be called any more, and all broadcast skbs to macvlan will be
discarded. This case can happen:
macvlan_process_broadcast() is the pending function of port->bc_work,
it moves all the skbs in port->bc_queue to the queue "list", and
processes the skbs in "list". During this, new skbs will keep being
added to port->bc_queue in macvlan_broadcast_enqueue(), and
port->bc_queue may already full when macvlan_process_broadcast()
return. This may happen, especially when there are a lot of real-time
threads and the process is preempted.
Fix this by calling schedule_work(&port->bc_work) even if
port->bc_work is full in macvlan_broadcast_enqueue().
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue") Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In case the completion function failes, unbind will be called
which will call cancel_work for awb_work.
This will trigger a WARN message from the workqueue.
To avoid this, move the INIT_WORK call at the start of the completion
function. This way the work is always initialized, which corresponds
to the 'always canceled' unbind code.
Fixes: 93d4a26c3d ("[media] atmel-isc: add the isc pipeline function") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The subsystem will free the asd memory on notifier cleanup, if the asd is
added to the notifier.
However the memory is freed using kfree.
Thus, we cannot allocate the asd using devm_*
This can lead to crashes and problems.
To test this issue, just return an error at probe, but cleanup the
notifier beforehand.
Fixes: 106267444f ("[media] atmel-isc: add the Image Sensor Controller code") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
After a PWM is disposed by its user the per chip data becomes invalid.
Clear the data in common code instead of the device drivers to get
consistent behaviour. Before this patch only three of nine drivers
cleaned up here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Errors are negative numbers. Using %u shows them as very large positive
numbers such as 4294967277 that don't make sense. Use the %d format
instead, and get a much nicer -19.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Fixes: b48e0bab142f ("net: macb: Migrate to devm clock interface") Fixes: 93b31f48b3ba ("net/macb: unify clock management") Fixes: 421d9df0628b ("net/macb: merge at91_ether driver into macb driver") Fixes: aead88bd0e99 ("net: ethernet: macb: Add support for rx_clk") Fixes: f5473d1d44e4 ("net: macb: Support clock management for tsu_clk") Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add parent device name to the name of devices on bus to avoid
device names collisions for same client UUID available
from different MEI heads. Namely this prevents sysfs collision under
/sys/bus/mei/device/
In the device part leave just UUID other parameters that are
required for device matching are not required here and are
just bloating the name.
Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191105150514.14010-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This device presents itself as a USB hub with three attached devices:
- An ACM serial port connected to the GPS module (not affected by this
commit)
- An FTDI serial port connected to the GPS module (1546:0502)
- Another FTDI serial port connected to the ODIN-W2 radio module
(1546:0503)
This commit registers U-Blox's VID and the PIDs of the second and third
devices.
Add 024c:0525 to the list of SDIO device-ids, based on a patch found
in the Android X86 kernels. According to that patch this device id is
used on the Alcatel Plus 10 device.
Reported-and-tested-by: youling257 <youling257@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111113846.24940-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver only binds by SDIO device-ids, all the ACPI device-id does
is causing the driver to load unnecessarily on devices where the DSDT
contains a bogus OBDA8723 device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111113846.24940-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The variable skb is released via kfree_skb() when the return value of
_rtl92e_tx is not zero. However, after that, skb is accessed again to
read its length, which may result in a use after free bug. This patch
fixes the bug by moving the release operation to where skb is never
used later.
Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1572965351-6745-1-git-send-email-bianpan2016@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The regmap update bits call was not selecting the proper mask, considering
the bits which was updating.
Update the mask from call to also include OSCBYPASS.
Removed MOSCEN which was not updated.
Fixes: 1bdf02326b71 ("clk: at91: make use of syscon/regmap internally") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lkml.kernel.org/r/1568042692-11784-1-git-send-email-eugen.hristev@microchip.com Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Vlastimil Babka [Fri, 29 Nov 2019 09:03:50 +0000 (10:03 +0100)]
mm, gup: add missing refcount overflow checks on s390
BugLink: https://bugs.launchpad.net/bugs/1855787
The mainline commit 8fde12ca79af ("mm: prevent get_user_pages() from
overflowing page refcount") was backported to 4.14.y stable as commit 04198de24771. The backport however missed that in 4.14, there are several
arch-specific gup.c versions with fast gup implementations, so these do not
prevent refcount overflow.
This stable-only commit fixes the s390 version, and is based on the backport in
SUSE SLES/openSUSE 4.12-based kernels.
The remaining architectures with own gup.c are sparc, mips, sh. It's unlikely
the known overflow scenario based on FUSE, which needs 140GB of RAM, is a
problem for those architectures, and I don't feel confident enough to patch
them.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 2b6f0090a333 ("mtd: Check add_mtd_device() ret code") contained
a leftover of the debug session that led to this bug fix. Remove this
pr_info().
Fixes: 2b6f0090a333 ("mtd: Check add_mtd_device() ret code") Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The ghes code is careful to parse and round firmware's advertised
memory requirements for CPER records, up to a maximum of 64K.
However when ghes_estatus_pool_expand() does its work, it splits
the requested size into PAGE_SIZE granules.
This means if firmware generates 5K of CPER records, and correctly
describes this in the table, __process_error() will silently fail as it
is unable to allocate more than PAGE_SIZE.
Switch the estatus pool to vmalloc() memory. On x86 vmalloc() memory
may fault and be fixed up by vmalloc_fault(). To prevent this call
vmalloc_sync_all() before an NMI handler could discover the memory.
Signed-off-by: James Morse <james.morse@arm.com> Reviewed-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
oops_begin() exists to group printk() messages with the oops message
printed by die(). To reach this caller we know that platform firmware
took this error first, then notified the OS via NMI with a 'panic'
severity.
Don't wait for another CPU to release the die-lock before panic()ing,
our only goal is to print this fatal error and panic().
This code is always called in_nmi(), and since commit 42a0bb3f7138
("printk/nmi: generic solution for safe printk in NMI"), it has been
safe to call printk() from this context. Messages are batched in a
per-cpu buffer and printed via irq-work, or a call back from panic().
Link: https://patchwork.kernel.org/patch/10313555/ Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Although the apparmorfs dentries are always dropped from the dentry cache
when the usage count drops to zero, there is no guarantee that this will
happen in aafs_remove(), as another thread might still be using it. In
this scenario, this means that the dentry will temporarily continue to
appear in the results of lookups, even after the call to aafs_remove().
In the case of removal of a profile - it also causes simple_rmdir()
on the profile directory to fail, as the directory won't be empty until
the usage counts of all child dentries have decreased to zero. This
results in the dentry for the profile directory leaking and appearing
empty in the file system tree forever.
Signed-off-by: Chris Coulson <chris.coulson@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to firmware error code definition, the error code of 2
means NOT_SUPPORTED, this patch changes it to NOT_SUPPORTED.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc077 ("debugfs: return error
values, not NULL"). syzbot has found a way to trigger multiple debugfs
files attempting to be created, which fails, and then the error code
gets passed to dentry_path_raw() which obviously does not like it.
Reported-by: Eric Biggers <ebiggers@kernel.org> Reported-and-tested-by: syzbot+7857962b4d45e602b8ad@syzkaller.appspotmail.com Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often") Reported-by: Marcin Stojek <marcin.stojek@nokia.com> Tested-by: Marcin Stojek <marcin.stojek@nokia.com> Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513f5 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <maloy@donjonn.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, blktrace will not show requests that don't have any data as
rq->__sector is initialized to -1 which is out of device range and thus
discarded by act_log_check(). This is most notably the case for cache
flush requests sent to the device. Fix the problem by making
blk_rq_trace_sector() return 0 for requests without initialized sector.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
To prevent races between smc_lgr_terminate() and smc_conn_free() add an
extra check of the lgr field before accessing it, and cancel a delayed
free_work when a new smc connection is created.
This fixes the problem that free_work cleared the lgr variable but
smc_lgr_terminate() or smc_conn_free() still access it in parallel.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Digging through the ioctls with Al because of the previous
patches, we found that on 64-bit decnet's dn_dev_ioctl()
is wrong, because struct ifreq::ifr_ifru is actually 24
bytes (not 16 as expected from struct sockaddr) due to the
ifru_map and ifru_settings members.
Clearly, decnet expects the ioctl to be called with a struct
like
struct ifreq_dn {
char ifr_name[IFNAMSIZ];
struct sockaddr_dn ifr_addr;
};
since it does
struct ifreq *ifr = ...;
struct sockaddr_dn *sdn = (struct sockaddr_dn *)&ifr->ifr_addr;
This means that DN_IFREQ_SIZE is too big for what it wants on
64-bit, as it is
sizeof(struct ifreq) - sizeof(struct sockaddr) +
sizeof(struct sockaddr_dn)
This assumes that sizeof(struct sockaddr) is the size of ifr_ifru
but that isn't true.
Fix this to use offsetof(struct ifreq, ifr_ifru).
This indeed doesn't really matter much - the result is that we
copy in/out 8 bytes more than we should on 64-bit platforms. In
case the "struct ifreq_dn" lands just on the end of a page though
it might lead to faults.
As far as I can tell, it has been like this forever, so it seems
very likely that nobody cares.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24
Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst
With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun
Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use a bitmap to keep track of which partition types we've already seen;
for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
sfc NICs. Prior to this patch they cause sysfs_warn_dup errors because
they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On a NOP double buffer update where current buffer address is the same
as the next buffer address, the SDW_UPDATE bit clears too late. As we
are now using this bit to determine when it is safe to signal flip
completion to userspace this will delay completion of atomic commits
where one plane doesn't change the buffer by a whole frame period.
Fix this by remembering the last buffer address and just skip the
double buffer update if it would not change the buffer address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: initialize last_bufaddr in ipu_pre_configure] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This should be 1 for normal allocations, 0 disables leak reporting.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Fixes: 85704cb8dcfd ("net/core/neighbour: tell kmemleak about hash tables") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The API of pci_alloc_irq_vectors_affinity() says it returns -ENOSPC if
fewer than @min_vecs interrupt vectors are available for @dev.
However, if a device supports MSI-X but not MSI and a caller requests
@min_vecs that can't be satisfied by MSI-X, we previously returned -EINVAL
(from the failed attempt to enable MSI), not -ENOSPC.
When -ENOSPC is returned, callers may reduce the number IRQs they request
and try again. Most callers can use the @min_vecs and @max_vecs
parameters to avoid this retry loop, but that doesn't work when using IRQ
affinity "nr_sets" because rebalancing the sets is driver-specific.
This return value bug has been present since pci_alloc_irq_vectors() was
added in v4.10 by aff171641d18 ("PCI: Provide sensible IRQ vector
alloc/free routines"), but it wasn't an issue because @min_vecs/@max_vecs
removed the need for callers to iteratively reduce the number of IRQs
requested and retry the allocation, so they didn't need to distinguish
-ENOSPC from -EINVAL.
In v5.0, 6da4b3ab9a6e ("genirq/affinity: Add support for allocating
interrupt sets") added IRQ sets to the interface, which reintroduced the
need to check for -ENOSPC and possibly reduce the number of IRQs requested
and retry the allocation.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Jens Axboe <axboe@fb.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Addresses-Coverity-ID: 1476406 ("Resource leak") Fixes: 46273cf7e009 ("tipc: fix a missing check of genlmsg_put") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
add_mtd_device() can fail. We should always check its return value
and gracefully handle the failure case. Fix the call sites where this
not done (in mtdpart.c) and add a __must_check attribute to the
prototype to avoid this kind of mistakes.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
lib/genalloc.c: In function 'gen_pool_add_virt':
lib/genalloc.c:190:10: error: implicit declaration of function 'vzalloc_node'; did you mean 'kzalloc_node'?
lib/genalloc.c:190:8: warning: assignment to 'struct gen_pool_chunk *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
lib/genalloc.c: In function 'gen_pool_destroy':
lib/genalloc.c:254:3: error: implicit declaration of function 'vfree'; did you mean 'kfree'?
Fixes: 6862d2fc8185 ('lib/genalloc.c: use vzalloc_node() to allocate the bitmap') Cc: Huang Shijie <sjhuang@iluvatar.ai> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Skidanov <alexey.skidanov@intel.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
/*
* This memory isn't freed when the device is put,
* I don't have a nice idea for that though. Conceptually
* dma_mask in struct device should not be a pointer.
* See http://thread.gmane.org/gmane.linux.kernel.pci/9081
*/
pdev->dev.dma_mask =
kmalloc(sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
Since this leak has existed for more than 8 years and it does not
reference other parts of the memory, let kmemleak ignore it, so users
don't need to waste time reporting this in the future.
Link: http://lkml.kernel.org/r/20181206160751.36211-1-cai@gmx.us Signed-off-by: Qian Cai <cai@gmx.us> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J . Wysocki" <rafael.j.wysocki@intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
kernel/fork.c:167:13: warning: no previous prototype for `arch_release_thread_stack' [-Wmissing-prototypes]
kernel/fork.c:779:13: warning: no previous prototype for `fork_init' [-Wmissing-prototypes]
Add the missing declaration in head file to fix this.
Also, remove arch_release_thread_stack() completely because no arch
seems to implement it since bb9d81264 (arch: remove tile port).
Link: http://lkml.kernel.org/r/1542170087-23645-1-git-send-email-wang.yi59@zte.com.cn Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some devices may have big memory on chip, such as over 1G. In some
cases, the nbytes maybe bigger then 4M which is the bounday of the
memory buddy system (4K default).
So use vzalloc_node() to allocate the bitmap. Also use vfree to free
it.
Link: http://lkml.kernel.org/r/20181225015701.6289-1-sjhuang@iluvatar.ai Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Skidanov <alexey.skidanov@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
gen_pool_alloc_algo() uses different allocation functions implementing
different allocation algorithms. With gen_pool_first_fit_align()
allocation function, the returned address should be aligned on the
requested boundary.
If chunk start address isn't aligned on the requested boundary, the
returned address isn't aligned too. The only way to get properly
aligned address is to initialize the pool with chunks aligned on the
requested boundary. If want to have an ability to allocate buffers
aligned on different boundaries (for example, 4K, 1MB, ...), the chunk
start address should be aligned on the max possible alignment.
This happens because gen_pool_first_fit_align() looks for properly
aligned memory block without taking into account the chunk start address
alignment.
To fix this, we provide chunk start address to
gen_pool_first_fit_align() and change its implementation such that it
starts looking for properly aligned block with appropriate offset
(exactly as is done in CMA).
Link: https://lkml.kernel.org/lkml/a170cf65-6884-3592-1de9-4c235888cc8a@intel.com Link: http://lkml.kernel.org/r/1541690953-4623-1-git-send-email-alexey.skidanov@intel.com Signed-off-by: Alexey Skidanov <alexey.skidanov@intel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Daniel Mentz <danielmentz@google.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit fa5e084e43eb ("vmscan: do not unconditionally treat zones that
fail zone_reclaim() as full") changed the return value of
node_reclaim(). The original return value 0 means NODE_RECLAIM_SOME
after this commit.
While the return value of node_reclaim() when CONFIG_NUMA is n is not
changed. This will leads to call zone_watermark_ok() again.
This patch fixes the return value by adjusting to NODE_RECLAIM_NOSCAN.
Since node_reclaim() is only called in page_alloc.c, move it to
mm/internal.h.
Link: http://lkml.kernel.org/r/20181113080436.22078-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Dirty flag of the journal should be cleared at the last stage of umount,
if do it before jbd2_journal_destroy(), then some metadata in uncommitted
transaction could be lost due to io error, but as dirty flag of journal
was already cleared, we can't find that until run a full fsck. This may
cause system panic or other corruption.
Link: http://lkml.kernel.org/r/20181121020023.3034-3-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Changwei Ge <ge.changwei@h3c.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
genlmsg_put could fail. The fix inserts a check of its return value, and
if it fails, returns -EMSGSIZE.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
atl1e_write_phy_reg() could fail. The fix issues an error message when
it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
clk_prepare() could fail, so let's check its status, and if it fails,
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>