The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094dbb ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol") Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com> Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a40432509 ("[IPV6]: Find option offset by type.") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails.
Fixes: 20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked") Signed-off-by: Anton Protopopov <aspsk@isovalent.com> Link: https://lore.kernel.org/r/20230522154558.2166815-1-aspsk@isovalent.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.
In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
results in the following code generation for a 64-bit field:
HW adds segment size to the payload length
in the IPv6 header. Fix payload length to
just TCP header length instead of 'TCP header
size + IPv6 header size'.
Fixes: 86d7476078b8 ("octeontx2-pf: TCP segmentation offload support") Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()
Tests passed: 201
Tests failed: 0
Cannot remove namespace file "/run/netns/ns1": No such file or directory
This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.
Redirect the error message to /dev/null to mute it.
V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2
Fixes: b60417a9f2b8 ("selftest: fib_tests: Always cleanup before exit") Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In mutex_init() lockdep identifies a lock by defining a special static
key for each lock class. However if we wrap the macro in a function,
like in drmm_mutex_init(), we end up generating:
The static __key here is what lockdep uses to identify the lock class,
however since this is just a normal function the key here will be
created once, where all callers then use the same key. In effect the
mutex->depmap.key will be the same pointer for different
drmm_mutex_init() callers. This then results in impossible lockdep
splats since lockdep thinks completely unrelated locks are the same lock
class.
To fix this turn drmm_mutex_init() into a macro such that it generates a
different "static struct lock_class_key __key" for each invocation,
which looks to be inline with what mutex_init() wants.
v2:
- Revamp the commit message with clearer explanation of the issue.
- Rather export __drmm_mutex_release() than static inline.
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Reported-by: Sarah Walker <sarah.walker@imgtec.com> Fixes: e13f13e039dc ("drm: Add DRM-managed mutex_init()") Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Jocelyn Falempe <jfalempe@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230519090733.489019-1-matthew.auld@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
these endpoints (and similarly for the radio-shark driver).
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
the endpoints.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
syzbot reported [0] a null-ptr-deref in sk_get_rmem0() while using
IPPROTO_UDPLITE (0x88):
14:25:52 executing program 1:
r0 = socket$inet6(0xa, 0x80002, 0x88)
We had a similar report [1] for probably sk_memory_allocated_add()
in __sk_mem_raise_allocated(), and commit c915fe13cbaa ("udplite: fix
NULL pointer dereference") fixed it by setting .memory_allocated for
udplite_prot and udplitev6_prot.
To fix the variant, we need to set either .sysctl_wmem_offset or
.sysctl_rmem.
Now UDP and UDPLITE share the same value for .memory_allocated, so we
use the same .sysctl_wmem_offset for UDP and UDPLITE.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com Fixes: fd867d51f889 ("net/core: generic support for disabling netdev features down stack") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
Reported-and-tested-by: syzbot+0e22d63dcebb802b9bc8@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Pavel Skripkin <paskripkin@gmail.com> Fixes: aaf7dbe07385 ("video: fbdev: udlfb: properly check endpoint type") Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation.
Fixes: 3ac7fe5a4aab ("infrastructure to debug (dynamic) objects") Reported-by: syzbot <syzbot+fe0c72f0ccbb93786380@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/6577e1fa-b6ee-f2be-2414-a2b51b1c5e30@I-love.SAKURA.ne.jp Closes: https://syzkaller.appspot.com/bug?extid=fe0c72f0ccbb93786380 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.
When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.
Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.
Before dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.
Fixes: dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()") Cc: stable@vger.kernel.org Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.
Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.
smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.
Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.
On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.
Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21
Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:
-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1
This is also expected to make the scheduler do rather wonky things
too.
[ dhansen: remove CPUID detail from changelog, add end user effects ]
CC: stable@kernel.org Fixes: bbb65d2d365e ("x86: use cpuid vector 0xb when available for detecting cpu topology") Fixes: 95f3d39ccf7a ("x86/cpu/topology: Provide detect_extended_topology_early()") Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The number of CHAs from the discovery table on some SPR variants is
incorrect, because of a firmware issue. An accurate number can be read
from the MSR UNC_CBO_CONFIG.
Fixes: 949b11381f81 ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support") Reported-by: Stephane Eranian <eranian@google.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Hardik Garg [Fri, 26 May 2023 23:21:36 +0000 (16:21 -0700)]
selftests/memfd: Fix unknown type name build failure
BugLink: https://bugs.launchpad.net/bugs/2028979
Partially backport v6.3 commit 11f75a01448f ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:
fuse_test.c:64:8: error: unknown type name '__u64'
64 | static __u64 mfd_assert_get_seals(int fd)
This header includes the __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.
[ cmllamas: clean forward port from commit 015ac18be7de ("binder: fix
UAF of alloc->vma in race with munmap()") in 5.10 stable. It is needed
in mainline after the revert of commit a43cfc87caaf ("android: binder:
stop saving a pointer to the VMA") as pointed out by Liam. The commit
log and tags have been tweaked to reflect this. ]
In commit 720c24192404 ("ANDROID: binder: change down_write to
down_read") binder assumed the mmap read lock is sufficient to protect
alloc->vma inside binder_update_page_range(). This used to be accurate
until commit dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in
munmap"), which now downgrades the mmap_lock after detaching the vma
from the rbtree in munmap(). Then it proceeds to teardown and free the
vma with only the read lock held.
This means that accesses to alloc->vma in binder_update_page_range() now
will race with vm_area_free() in munmap() and can cause a UAF as shown
in the following KASAN trace:
==================================================================
BUG: KASAN: use-after-free in vm_insert_page+0x7c/0x1f0
Read of size 8 at addr ffff16204ad00600 by task server/558
To prevent the race above, revert back to taking the mmap write lock
inside binder_update_page_range(). One might expect an increase of mmap
lock contention. However, binder already serializes these calls via top
level alloc->mutex. Also, there was no performance impact shown when
running the binder benchmark tests.
Fixes: c0fd2101781e ("Revert "android: binder: stop saving a pointer to the VMA"") Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Closes: https://lore.kernel.org/all/20230518144052.xkj6vmddccq4v66b@revolver Cc: <stable@vger.kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Liam Howlett <liam.howlett@oracle.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20230519195950.1775656-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In binder_transaction_buffer_release() the 'failed_at' offset indicates
the number of objects to clean up. However, this function was changed by
commit 44d8047f1d87 ("binder: use standard functions to allocate fds"),
to release all the objects in the buffer when 'failed_at' is zero.
This introduced an issue when a transaction buffer is released without
any objects having been processed so far. In this case, 'failed_at' is
indeed zero yet it is misinterpreted as releasing the entire buffer.
This leads to use-after-free errors where nodes are incorrectly freed
and subsequently accessed. Such is the case in the following KASAN
report:
==================================================================
BUG: KASAN: slab-use-after-free in binder_thread_read+0xc40/0x1f30
Read of size 8 at addr ffff4faf037cfc58 by task poc/474
In order to avoid these issues, let's always calculate the intended
'failed_at' offset beforehand. This is renamed and wrapped in a helper
function to make it clear and convenient.
Fixes: 32e9f56a96d8 ("binder: don't detect sender/target during buffer cleanup") Reported-by: Zi Fan Tan <zifantan@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20230505203020.4101154-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Bring back the original lockless design in binder_alloc to determine
whether the buffer setup has been completed by the ->mmap() handler.
However, this time use smp_load_acquire() and smp_store_release() to
wrap all the ordering in a single macro call.
Also, add comments to make it evident that binder uses alloc->vma to
determine when the binder_alloc has been fully initialized. In these
scenarios acquiring the mmap_lock is not required.
Fixes: a43cfc87caaf ("android: binder: stop saving a pointer to the VMA") Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20230502201220.1756319-3-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch fixed an issue reported by syzkaller in [1]. However, this
turned out to be only a band-aid in binder. The root cause, as bisected
by syzkaller, was fixed by commit 5789151e48ac ("mm/mmap: undo ->mmap()
when mas_preallocate() fails"). We no longer need the patch for binder.
Reverting such patch allows us to have a lockless access to alloc->vma
in specific cases where the mmap_lock is not required. This approach
avoids the contention that caused a performance regression.
This caused a performance regression particularly when pages are getting
reclaimed. We don't need to acquire the mmap_lock to determine when the
binder buffer has been fully initialized. A subsequent patch will bring
back the lockless approach for this.
[cmllamas: resolved trivial conflicts with renaming of alloc->mm]
Fixes: 44e602b4e52f ("binder_alloc: add missing mmap_lock calls when using the VMA") Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20230502201220.1756319-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Printing the other clock types should not be conditioned on being able
to print OD_SCLK. Some GPUs currently have limited capability of only
printing a subset of these.
Since this condition was introduced in v5.18-rc1, reading from
`pp_od_clk_voltage` has been returning empty on the Asus ROG Strix G15
(2021).
Fixes: 79c65f3fcbb1 ("drm/amd/pm: do not expose power implementation details to amdgpu_pm.c") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Jonatas Esteves <jntesteves@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Otherwise, the power source switching will fail due to message
unavailable.
Fixes: bf4823267a81 ("drm/amd/pm: fix possible power mode mismatch between driver and PMFW") Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Guchun Chen <guchun.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Put back the radeon_dp_work_func logic. It seems that
handling DP RX interrupts is necessary to make some
panels work. This was removed with the MST support,
but it regresses some systems so add it back. While
we are here, add the proper mutex locking.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2567 Fixes: 01ad1d9c2888 ("drm/radeon: Drop legacy MST support") Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When mgag200 switched from simple KMS to regular atomic helpers,
the initialization of the gamma settings was lost.
This leads to a black screen, if the bios/uefi doesn't use the same
pixel color depth.
v2: rebase on top of drm-misc-fixes, and add Cc stable tag.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2171155 Fixes: 1baf9127c482 ("drm/mgag200: Replace simple-KMS with regular atomic helpers") Cc: <stable@vger.kernel.org> Tested-by: Phil Oester <kernel@linuxace.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230510131034.284078-1-jfalempe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using
device_property_read_u16(). It resulted in 0 if a 32bit value was used
in dts. This commit fixes the dt binding doc to declare it as u16.
Cc: stable@vger.kernel.org Fixes: 68989fe1c39d ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have. The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here. Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's debugfs files have had a read operation since commit 2a9e27408e12 ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
When patching the kernel code some alternatives depend on SMP vs. !SMP.
Use the value of num_present_cpus() instead of num_online_cpus() to
decide, otherwise we may run into issues if and additional CPU is
enabled after having loaded a module while only one CPU was enabled.
Signed-off-by: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v6.1+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
gcc-13 may generate calls for __bswap{si,di}2. This breaks the kernel
build when optimization for size is selected. Add __bswap{si,di}2
helpers to fix that.
Cc: stable@vger.kernel.org Fixes: 19c5699f9aff ("xtensa: don't link with libgcc") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fetch function descriptor pointed to by the signal handler pointer from
userspace on signal delivery and function pointer pointed to by the
sa_restorer on return from the signal handler.
Cc: stable@vger.kernel.org Fixes: e3ddb8bbe0f8 ("xtensa: add FDPIC and static PIE support for noMMU") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Link: https://lore.kernel.org/all/CAMuHMdW3yD22_ApemzW_6me3adq6A458u1_F0v-1EYwK_62jPA@mail.gmail.com/ Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: stable@vger.kernel.org Co-developed-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@linux-m68k.org> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Link: https://lore.kernel.org/r/9e66262a754fcba50208aa424188896cc52a1dd1.1683365892.git.fthain@linux-m68k.org Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be147 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org Signed-off-by: Matthias Kaehlcke <mka@chromium.org Reviewed-by: Douglas Anderson <dianders@chromium.org Reviewed-by: Stephen Boyd <swboyd@chromium.org Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection") Cc: stable@vger.kernel.org Cc: Marek Vasut <marex@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d07929 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 614f0388f580 ("mmc: block: move single ioctl() commands to block requests") Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
After commit 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate
ESDHC_FLAG_HS400* only on 8bit bus"), the property "no-mmc-hs400"
from device tree file do not work any more.
This patch reorder the code, which can avoid the warning message
"drop HS400 support since no 8-bit bus" and also make the property
"no-mmc-hs400" from dts file works.
Fixes: 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230504112222.3599602-1-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some calls to rpc_exit_task() may deliberately change the value of
task->tk_status, for instance because it gets checked by the RPC call's
rpc_release() callback. That makes it wrong to reset the value to
task->tk_rpc_status.
In particular this causes a bug where the rpc_call_done() callback tries
to fail over a set of pNFS/flexfiles writes to a different IP address,
but the reset of task->tk_status causes nfs_commit_release_pages() to
immediately mark the file as having a fatal error.
Fixes: 39494194f93b ("SUNRPC: Fix races with rpc_killall_tasks()") Cc: stable@vger.kernel.org # 6.1.x Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
Signed-off-by: Bin Li <bin.li@canonical.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20230524113755.1346928-1-bin.li@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It's reported that the recording started right after the driver probe
doesn't work properly, and it turned out that this is related with the
codec auto-suspend. Namely, after the probe phase, the usage count
goes zero, and the auto-suspend is programmed, but the codec is kept
still active until the auto-suspend expiration. When an application
(e.g. alsactl) updates the mixer values at this moment, the values are
cached but not actually written. Then, starting arecord thereafter
also results in the silence because of the missing unmute.
The root cause is the handling of "lazy update" mode; when a mixer
value is updated *after* the suspend, it should update only the cache
and exits. At the resume, the cached value is written to the device,
in turn. The problem is that the current code misinterprets the state
of auto-suspend as if it were already suspended.
Although we can add the check of the actual device state after
pm_runtime_get_if_in_use() for catching the missing state, this won't
suffice; the second call of regmap_update_bits_check() will skip
writing the register because the cache has been already updated by the
first call. So we'd need fixes in two different places.
OTOH, a simpler fix is to replace pm_runtime_get_if_in_use() with
pm_runtime_get_if_active() (with ign_usage_count=true). This change
implies that the driver takes the pm refcount if the device is still
in ACTIVE state and continues the processing. A small caveat is that
this will leave the auto-suspend timer. But, since the timer callback
itself checks the device state and aborts gracefully when it's active,
this won't be any substantial problem.
Long story short: we address the missing register-write problem just
by replacing the pm_runtime_*() call in snd_hda_keep_power_up().
Correct this by calling INIT_WORK_ONSTACK instead of INIT_WORK.
Fixes: 684ec215706d ("platform/x86/intel/ifs: Authenticate and copy to secured memory") Signed-off-by: David Arcari <darcari@redhat.com> Cc: Jithu Joseph <jithu.joseph@intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230523105400.674152-1-darcari@redhat.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In preparation for removing security_old_inode_init_security(), switch to
security_inode_init_security().
Extend the existing ocfs2_initxattrs() to take the
ocfs2_security_xattr_info structure from fs_info, and populate the
name/value/len triple with the first xattr provided by LSMs.
As fs_info was not used before, ocfs2_initxattrs() can now handle the case
of replicating the behavior of security_old_inode_init_security(), i.e.
just obtaining the xattr, in addition to setting all xattrs provided by
LSMs.
Supporting multiple xattrs is not currently supported where
security_old_inode_init_security() was called (mknod, symlink), as it
requires non-trivial changes that can be done at a later time. Like for
reiserfs, even if EVM is invoked, it will not provide an xattr (if it is
not the first to set it, its xattr will be discarded; if it is the first,
it does not have xattrs to calculate the HMAC on).
Finally, since security_inode_init_security(), unlike
security_old_inode_init_security(), returns zero instead of -EOPNOTSUPP if
no xattrs were provided by LSMs or if inodes are private, additionally
check in ocfs2_init_security_get() if the xattr name is set.
If not, act as if security_old_inode_init_security() returned -EOPNOTSUPP,
and set si->enable to zero to notify to the functions following
ocfs2_init_security_get() that no xattrs are available.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Reviewed-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
This is the fix for the defect of commit ab144f0b4ad6
("drm/amd/display: Allow individual control of eDP hotplug support").
[How]
To revise the default eDP hotplug setting and use the enum to git rid
of the magic number for different options.
Fixes: ab144f0b4ad6 ("drm/amd/display: Allow individual control of eDP hotplug support") Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eeefe7c4820b6baa0462a8b723ea0a3b5846ccae)
Hand modified for missing file rename changes and symbol moves in 6.1.y. Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Signed-off-by: Gregory Oakes <gregory.oakes@amd.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230316201312.17538-1-gregory.oakes@amd.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in
tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero
bytes. This prevents hwrng from racing during resume.
Cc: stable@vger.kernel.org Fixes: 6e592a065d51 ("tpm: Move Linux RNG connection to hwrng") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
TPM chip bootstrapping was removed from tpm_chip_register(), and it
was relocated to tpm_tis_core. This breaks all drivers which are not
based on tpm_tis because the chip will not get properly initialized.
Take the corrective steps:
1. Rename tpm_chip_startup() as tpm_chip_bootstrap() and make it one-shot.
2. Call tpm_chip_bootstrap() in tpm_chip_register(), which reverts the
things as tehy used to be.
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com> Fixes: 548eb516ec0f ("tpm, tpm_tis: startup chip before testing for interrupts") Reported-by: Pengfei Xu <pengfei.xu@intel.com> Link: https://lore.kernel.org/all/ZEjqhwHWBnxcaRV5@xpf.sh.intel.com/ Tested-by: Pengfei Xu <pengfei.xu@intel.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 99d464506255 ("tpm: Prevent hwrng from activating during resume") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In tpm_tis_gen_interrupt() a request for a property value is sent to the
TPM to test if interrupts are generated. However after a power cycle the
TPM responds with TPM_RC_INITIALIZE which indicates that the TPM is not
yet properly initialized.
Fix this by first starting the TPM up before the request is sent. For this
the startup implementation is removed from tpm_chip_register() and put
into the new function tpm_chip_startup() which is called before the
interrupts are tested.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 99d464506255 ("tpm: Prevent hwrng from activating during resume") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Before sending a TPM command, CLKRUN protocol must be disabled. This is not
done in the case of tpm1_do_selftest() call site inside tpm_tis_resume().
Address this by decorating the calls with tpm_chip_{start,stop}, which
should be always used to arm and disarm the TPM chip for transmission.
Finally, move the call to the main TPM driver callback as the last step
because it should arm the chip by itself, if it needs that type of
functionality.
Cc: stable@vger.kernel.org Reported-by: Jason A. Donenfeld <Jason@zx2c4.com> Closes: https://lore.kernel.org/linux-integrity/CS68AWILHXS4.3M36M1EKZLUMS@suppilovahvero/ Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to the TPM Interface Specification (TIS) support for "stsValid"
and "commandReady" interrupts is only optional.
This has to be taken into account when handling the interrupts in functions
like wait_for_tpm_stat(). To determine the supported interrupts use the
capability query.
Also adjust wait_for_tpm_stat() to only wait for interrupt reported status
changes. After that process all the remaining status changes by polling
the status register.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 1398aa803f19 ("tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resume") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The interrupt handler that sets the boolean variable irq_tested may run on
another CPU as the thread that checks irq_tested as part of the irq test in
tpm_tis_send().
Since nothing guarantees cache coherency between CPUs for unsynchronized
accesses to boolean variables the testing thread might not perceive the
value change done in the interrupt handler.
Avoid this issue by setting the bit TPM_TIS_IRQ_TESTED in the flags field
of the tpm_tis_data struct and by accessing this field with the bit
manipulating functions that provide cache coherency.
Also convert all other existing sites to use the proper macros when
accessing this bitfield.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 1398aa803f19 ("tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resume") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc82968 ("usb: dwc3: gadget: conditionally disable Link State change events") Cc: stable <stable@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com> Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
1) A page in a PROT_READ|PROT_WRITE VMA is faulted.
2) Page migration allocates a page with the KASAN allocator,
causing it to receive a non-match-all tag, and uses it
to replace the page faulted in 1.
3) The program uses mprotect() to enable PROT_MTE on the page faulted in 1.
As a result of step 3, we are left with a non-match-all tag for a page
with tags accessible to userspace, which can lead to the same kind of
tag check faults that commit e74a68468062 ("arm64: Reset KASAN tag in
copy_highpage with HW tags only") intended to fix.
The general invariant that we have for pages in a VMA with VM_MTE_ALLOWED
is that they cannot have a non-match-all tag. As a result of step 2, the
invariant is broken. This means that the fix in the referenced commit
was incomplete and we also need to reset the tag for pages without
PG_mte_tagged.
Fixes: e5b8d9218951 ("arm64: mte: reset the page tag in page->flags") Cc: <stable@vger.kernel.org> # 5.15 Link: https://linux-review.googlesource.com/id/I7409cdd41acbcb215c2a7417c1e50d37b875beff Signed-off-by: Peter Collingbourne <pcc@google.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20230420210945.2313627-1-pcc@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the special handling of qcom,adreno-smmu was moved into
qcom_smmu_create(), it was overlooked that we didn't have all the
required entries in qcom_smmu_impl_of_match. So we stopped getting
adreno_smmu_priv on sc7180, breaking per-process pgtables.
Fixes: 30b912a03d91 ("iommu/arm-smmu-qcom: Move the qcom,adreno-smmu check into qcom_smmu_create") Cc: <stable@vger.kernel.org> Suggested-by: Lepton Wu <lepton@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/537357/ Link: https://lore.kernel.org/r/20230516222039.907690-1-robdclark@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The script command does not support aggregation modes by itself although
that can be achieved using post-processing scripts. Because of this, it
does not allocate memory for aggregated event values.
Upon running perf stat record, the aggregation mode is set in the perf
data file. If the mode is AGGR_GLOBAL, the aggregated event values are
accessed and this leads to a segmentation fault since these were never
allocated to begin with. Set the mode to AGGR_NONE explicitly to avoid
this.
E.g.
$ perf stat record -e cycles true
$ perf script
Before:
Segmentation fault (core dumped)
After:
CPU THREAD VAL ENA RUN TIME EVENT
-1 231919 162831 362069 362069 935289 cycles:u
Fixes: 8b76a3188b85724f ("perf stat: Remove unused perf_counts.aggr field") Signed-off-by: Sandipan Das <sandipan.das@amd.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ananth Narayan <ananth.narayan@amd.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nick Terrell <terrelln@fb.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Cc: stable@vger.kernel.org # v6.2+ Link: https://lore.kernel.org/r/83d6c6c05c54bf00c5a9df32ac160718efca0c7a.1683280603.git.sandipan.das@amd.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Until now, the page table walker counted increments to the PA and IPA
of a walk in two separate places. While the PA is incremented as soon as
a leaf PTE is installed in stage2_map_walker_try_leaf(), the IPA is
actually bumped in the generic table walker context. Critically,
__kvm_pgtable_visit() rereads the PTE after the LEAF callback returns
to work out if a table or leaf was installed, and only bumps the IPA for
a leaf PTE.
This arrangement worked fine when we handled faults behind the write lock,
as the walker had exclusive access to the stage-2 page tables. However,
commit 1577cb5823ce ("KVM: arm64: Handle stage-2 faults in parallel")
started handling all stage-2 faults behind the read lock, opening up a
race where a walker could increment the PA but not the IPA of a walk.
Nothing good ensues, as the walker starts mapping with the incorrect
IPA -> PA relationship.
For example, assume that two vCPUs took a data abort on the same IPA.
One observes that dirty logging is disabled, and the other observed that
it is enabled:
Bring an end to the whole mess by using the IPA as the single source of
truth for how far along a walk has gotten. Work out the correct PA to
map by calculating the IPA offset from the beginning of the walk and add
that to the starting physical address.
Cc: stable@vger.kernel.org Fixes: 1577cb5823ce ("KVM: arm64: Handle stage-2 faults in parallel") Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230421071606.1603916-2-oliver.upton@linux.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
qsel_to_ep[] can be assigned negative value, so change type from 'u8' to
'int'. Otherwise, Smatch static checker warns:
drivers/net/wireless/realtek/rtw88/usb.c:219 rtw_usb_parse() warn:
assigning (-22) to unsigned variable 'rtwusb->qsel_to_ep[8]'
Cc: stable@vger.kernel.org Fixes: a6f187f92bcc ("wifi: rtw88: usb: fix priority queue to endpoint mapping") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/linux-wireless/c3f70197-829d-48ed-ae15-66a9de80fa90@kili.mountain/ Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230508085539.46795-1-pkshih@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the PCI and USB cases try a manual lookup of the id so that manually
binding the driver through sysfs and more importantly brcmf_pcie_probe()
on resume will work.
For the SDIO case there is no helper to do a manual sdio_device_id lookup,
so just directly error out on a NULL id there.
Fixes: da6d9c8ecd00 ("wifi: brcmfmac: add firmware vendor info in driver info") Reported-by: Felix <nimrod4garoa@gmail.com> Link: https://lore.kernel.org/regressions/4ef3f252ff530cbfa336f5a0d80710020fc5cb1e.camel@gmail.com/ Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230510141856.46532-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.
Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);
The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING
While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING
When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.
Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.
Fixes: 7598f4b40bd6 ("iavf: Move netdev_update_features() into watchdog task") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.
Fixes: 26312c685ae0 ("net: fec: correct the counting of XDP sent frames") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Failure to add offloaded policy will cause to the following
error once user will try to reload driver.
Unregister_netdevice: waiting for eth3 to become free. Usage count = 2
This was caused by xfrm_dev_policy_add() which increments reference
to net_device. That reference was supposed to be decremented
in xfrm_dev_policy_free(). However the latter wasn't called.
unregister_netdevice: waiting for eth3 to become free. Usage count = 2
leaked reference.
xfrm_dev_policy_add+0xff/0x3d0
xfrm_policy_construct+0x352/0x420
xfrm_add_policy+0x179/0x320
xfrm_user_rcv_msg+0x1d2/0x3d0
netlink_rcv_skb+0xe0/0x210
xfrm_netlink_rcv+0x45/0x50
netlink_unicast+0x346/0x490
netlink_sendmsg+0x3b0/0x6c0
sock_sendmsg+0x73/0xc0
sock_write_iter+0x13b/0x1f0
vfs_write+0x528/0x5d0
ksys_write+0x120/0x150
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 919e43fad516 ("xfrm: add an interface to offload policy") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
More arrays (and arguments) for dcpd were set to 16, when it looks like
DP_RECEIVER_CAP_SIZE (15) should be used. Fix the remaining cases, seen
with GCC 13:
../drivers/gpu/drm/nouveau/nvif/outp.c: In function 'nvif_outp_acquire_dp':
../include/linux/fortify-string.h:57:33: warning: array subscript 'unsigned char[16][0]' is partly outside array bounds of 'u8[15]' {aka 'unsigned char[15]'} [-Warray-bounds=]
57 | #define __underlying_memcpy __builtin_memcpy
| ^
...
../drivers/gpu/drm/nouveau/nvif/outp.c:140:9: note: in expansion of macro 'memcpy'
140 | memcpy(args.dp.dpcd, dpcd, sizeof(args.dp.dpcd));
| ^~~~~~
../drivers/gpu/drm/nouveau/nvif/outp.c:130:49: note: object 'dpcd' of size [0, 15]
130 | nvif_outp_acquire_dp(struct nvif_outp *outp, u8 dpcd[DP_RECEIVER_CAP_SIZE],
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 813443721331 ("drm/nouveau/disp: move DP link config into acquire") Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Lyude Paul <lyude@redhat.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com> Cc: dri-devel@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <git@karolherbst.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230204184307.never.825-kees@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
To avoid new mes fw running with old driver, rename
mes schq fw to gc_*_mes_2.bin.
v2: add MODULE_FIRMWARE declaration
v3: squash in fixup patch
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
These functions are already marked as NOKPROBE to prevent recursion and
we have the same reason to blacklist them if rethook is used with fprobe,
since they are beyond the recursion-free region ftrace can guard.
Link: https://lore.kernel.org/all/20230517034510.15639-5-zegao@tencent.com/ Fixes: f3a112c0c40d ("x86,rethook,kprobes: Replace kretprobe with rethook on x86") Signed-off-by: Ze Gao <zegao@tencent.com> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch replaces preempt_{disable, enable} with its corresponding
notrace version in rethook_trampoline_handler so no worries about stack
recursion or overflow introduced by preempt_count_{add, sub} under
fprobe + rethook context.
Link: https://lore.kernel.org/all/20230517034510.15639-2-zegao@tencent.com/ Fixes: 54ecbe6f1ed5 ("rethook: Add a generic return hook") Signed-off-by: Ze Gao <zegao@tencent.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The mte_sync_page_tags() function sets PG_mte_tagged if it initializes
page tags. Then we return to mte_sync_tags(), which sets PG_mte_tagged
again. At best, this is redundant. However, it is possible for
mte_sync_page_tags() to return without having initialized tags for the
page, i.e. in the case where check_swap is true (non-compound page),
is_swap_pte(old_pte) is false and pte_is_tagged is false. So at worst,
we set PG_mte_tagged on a page with uninitialized tags. This can happen
if, for example, page migration causes a PTE for an untagged page to
be replaced. If the userspace program subsequently uses mprotect() to
enable PROT_MTE for that page, the uninitialized tags will be exposed
to userspace.
Fix it by removing the redundant call to set_page_mte_tagged().
Fixes: e059853d14ca ("arm64: mte: Fix/clarify the PG_mte_tagged semantics") Signed-off-by: Peter Collingbourne <pcc@google.com> Cc: <stable@vger.kernel.org> # 6.1 Link: https://linux-review.googlesource.com/id/Ib02d004d435b2ed87603b858ef7480f7b1463052 Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Link: https://lore.kernel.org/r/20230420214327.2357985-1-pcc@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Cc: Steffen Maier <maier@linux.ibm.com> Fixes: 8129ee164267 ("[PATCH] s390: qdio V=V pass-through") Cc: <stable@vger.kernel.org> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 349d03ffd5f6 ("crypto: s390 - add crypto library interface for
ChaCha20") added a library interface to the s390 specific ChaCha20
implementation. However no check was added to verify if the required
facilities are installed before branching into the assembler code.
If compiled into the kernel, this will lead to the following crash,
if vector instructions are not available:
Formatting a thin-provisioned (ESE) device that is part of a PPRC copy
relation might fail with the following error:
dasd-eckd 0.0.f500: An error occurred in the DASD device driver, reason=09
[...]
24 Byte: 0 MSG 4, no MSGb to SYSOP
During format of an ESE disk the Release Allocated Space command is used.
A bit in the payload of the command is set that is not allowed to be set
for devices in a copy relation. This bit is set to allow the partial
release of an extent.
Check for the existence of a copy relation before setting the respective
bit.
Fixes: 91dc4a197569 ("s390/dasd: Add new ioctl to release space") Cc: stable@kernel.org # 5.3+ Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Link: https://lore.kernel.org/r/20230519102340.3854819-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached.
projects / mirror_ubuntu-kernels.git / log