Rasmus Villemoes [Thu, 12 Feb 2015 14:15:17 +0000 (15:15 +0100)]
hwmon: (ibmpex) Allow format string checking
The only difference between the three power_sensor_name_templates is
whether there is a suffix of "", "_lowest" or "_highest". We might as
well pull those into an array and use a literal format string,
allowing gcc to do type checking of the arguments to
sprintf. Incidentially, the same three suffixes are used in the
temp_sensor_name_templates case, so we end up eliminating one static
array.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: Fixed line length over 80 characters] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Linus Torvalds [Sun, 8 Mar 2015 19:47:18 +0000 (12:47 -0700)]
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Linus Torvalds [Sun, 8 Mar 2015 19:25:40 +0000 (12:25 -0700)]
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Linus Torvalds [Sun, 8 Mar 2015 19:15:47 +0000 (12:15 -0700)]
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
Linus Torvalds [Sun, 8 Mar 2015 18:51:04 +0000 (11:51 -0700)]
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Linus Torvalds [Sat, 7 Mar 2015 19:31:17 +0000 (11:31 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kernel/module.c: Update debug alignment after symtable generation
arm64: Don't use is_module_addr in setting page attributes
Johan Hovold [Wed, 4 Mar 2015 09:39:07 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent maximum timeout
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 4 Mar 2015 09:39:06 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent on 64-bit machines
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:24:28 +0000 (10:24 -0500)]
serial: uapi: Declare all userspace-visible io types
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:18:16 +0000 (10:18 -0500)]
serial: core: Fix iotype userspace breakage
commit 3ffb1a8193bea ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 16 Feb 2015 14:39:04 +0000 (22:39 +0800)]
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:11:05 +0000 (10:11 -0500)]
console: Fix console name size mismatch
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Cc: <stable@vger.kernel.org> # all, as b0b885657 was backported Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Desmond Liu [Fri, 27 Feb 2015 00:35:57 +0000 (16:35 -0800)]
serial: 8250_dw: Fix get_mctrl behaviour
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reported-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO") Reported-By: Nicolas Schichan <nschichan@freebox.fr> Debuged-By: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 7 Mar 2015 00:54:22 +0000 (16:54 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon, imx, msm, and i915 fixes.
The msm, imx and i915 ones are fairly run of the mill.
Radeon had some DP audio and posting reads for irq fixes, along with a
fix for 32-bit kernels with new cards, we were using unsigned long to
represent GPU side memory space, but since that changed size on 32 vs
64 cards with lots of VRAM failed, so the change has no effect on
x86-64, just moves to using uint64_t instead"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/msm: kexec fixes
drm/msm/mdp5: fix cursor blending
drm/msm/mdp5: fix cursor ROI
drm/msm/atomic: Don't leak atomic commit object when commit fails
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
drm/msm: update generated headers (add 6th lm.base entry)
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
drm/ttm: device address space != CPU address space
drm/mm: Support 4 GiB and larger ranges
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
...
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the idea behind the cross-check is to prevent acquire semaphore when
there is no release callback and vice versa. Thus, patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:08 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix sparse warnings
There is no need to export functions that are used as the callbacks in the
struct dw_i2c_dev. Otherwise we get the following warnings:
drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static?
drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static?
While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from
functions exported to the modules and redundant assignment of local sem
variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:07 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix typo in error path
It seems we have same message for different return values in get_sem() and
baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:06 +0000 (19:06 +0200)]
i2c: designware-baytrail: describe magic numbers
The patch converts hardcoded numerical constants to a named ones.
While here, align the variable name in get_sem() and reset_semaphore().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Fri, 6 Mar 2015 21:52:54 +0000 (13:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Outside of misc fixes, Filipe has a few fsync corners and we're
pulling in one more of Josef's fixes from production use here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref.
Btrfs: fix data loss in the fast fsync path
Btrfs: remove extra run_delayed_refs in update_cowonly_root
Btrfs: incremental send, don't rename a directory too soon
btrfs: fix lost return value due to variable shadowing
Btrfs: do not ignore errors from btrfs_lookup_xattr in do_setxattr
Btrfs: fix off-by-one logic error in btrfs_realloc_node
Btrfs: add missing inode update when punching hole
Btrfs: abort the transaction if we fail to update the free space cache inode
Btrfs: fix fsync race leading to ordered extent memory leaks
Linus Torvalds [Fri, 6 Mar 2015 21:43:33 +0000 (13:43 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- adding Lukasz as maintainer of samsung thermal driver.
- driver fixes: exynos and int430x.
- one fix in the exynos cpufreq driver related to cpu cooling (acked
by cpufreq maintainer).
- fix default sysfs attributes of cooling devices
Note: I am sending this pull on Rui's behalf while he fixes issues in his Linux box"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: Make sysfs attributes of cooling devices default attributes
Thermal/int340x: Fix memleak for aux trip
MAINTAINERS: Add entry for SAMSUNG THERMAL DRIVER
cpufreq: exynos: Use simple approach to asses if cpu cooling can be used
thermal: exynos: Fix wrong control of power down detection mode for Exynos7
Dave Airlie [Fri, 6 Mar 2015 21:40:17 +0000 (07:40 +1000)]
Merge tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel into drm-fixes
two fixes, both cc'd stable.
* tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
Linus Torvalds [Fri, 6 Mar 2015 18:55:41 +0000 (10:55 -0800)]
Merge tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few more ASoC changes that have been gathered since rc1,
but it's still fairly calm over all. The only largish LOC is found in
atmel driver, and it's just a removal of broken non-DT stuff. The
rest are all small driver-specific fixes, nothing to worry much"
* tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - One more Dell macine needs DELL1_MIC_NO_PRESENCE quirk
ALSA: opl3: small array underflow
ALSA: line6: Clamp values correctly
ALSA: msnd: add some missing curly braces
ASoC: omap-pcm: Correct dma mask
ASoC: simple-card: Add a NULL pointer check in asoc_simple_card_dai_link_of
ASoC: sam9g20_wm8731: drop machine_is_xxx
ALSA: dice: fix wrong offsets for Dice interface
ALSA: oxfw: fix a condition and return code in start_stream()
ASoC: OMAP: mcbsp: Fix CLKX and CLKR pinmux when used as inputs
ASoC: rt5677: Correct the routing paths of that after IF1/2 DACx Mux
ASoC: sta32x: fix register range in regmap.
ASoC: rt5670: Set RT5670_IRQ_CTRL1 non volatile
ASoC: Intel: reset the DSP while suspending
ASoC: Intel: save and restore the CSR register
ASoC: Intel: update MMX ID to 3
ASoC: max98357a: Add missing header files
ASoC: cirrus: tlv320aic23 needs I2C
ASoC: Samsung: add missing I2C/SPI dependencies
ASoC: rt5670: Fix the speaker mono output issue
...
Linus Torvalds [Fri, 6 Mar 2015 18:36:09 +0000 (10:36 -0800)]
Merge tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (ACPI resources management,
suspend-to-idle), stable-candidate fixes (ACPI backlight), fixes
related to the wakeup IRQ management changes made in v3.18, other
fixes (suspend-to-idle, cpufreq ppc driver) and a couple of cleanups
(suspend-to-idle, generic power domains, ACPI backlight).
Specifics:
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while at
it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to an
unexpected combination of interrupt action handler flags. However,
on at91 a timer IRQ is shared with some other devices (including
system wakeup ones) and that leads to the unusual combination of
flags in question.
To make it possible to avoid the warning introduce a new interrupt
action handler flag (which can be used by drivers to indicate the
special case to the core) and rework the problematic at91 drivers
to use it and work as expected during system suspend/resume. From
Boris Brezillon, Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman)"
* tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
genirq / PM: describe IRQF_COND_SUSPEND
tty: serial: atmel: rework interrupt and wakeup handling
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
cpuidle / sleep: Use broadcast timer for states that stop local timer
clk: at91: implement suspend/resume for the PMC irqchip
rtc: at91rm9200: rework wakeup and interrupt handling
rtc: at91sam9: rework wakeup and interrupt handling
PM / wakeup: export pm_system_wakeup symbol
genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
ACPI / video: Propagate the error code for acpi_video_register
ACPI / video: Load the module even if ACPI is disabled
PM / Domains: cleanup: rename gpd -> genpd in debugfs interface
cpufreq: ppc: Add missing #include <asm/smp.h>
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
PCI: versatile: Update for list_for_each_entry() API change
genirq / PM: better describe IRQF_NO_SUSPEND semantics
Linus Torvalds [Fri, 6 Mar 2015 18:09:57 +0000 (10:09 -0800)]
Merge tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix a regression in the NFSv4 open state recovery code
- Fix a regression in the NFSv4 close code
- Fix regressions and side-effects of the loop-back mounted NFS fixes
in 3.18, that cause the NFS read() syscall to return EBUSY.
- Fix regressions around the readdirplus code and how it interacts
with the VFS lazy unmount changes that went into v3.18.
- Fix issues with out-of-order RPC call replies replacing updated
attributes with stale ones (particularly after a truncate()).
- Fix an underflow checking issue with RPC/RDMA credits
- Fix a number of issues with the NFSv4 delegation return/free code.
- Fix issues around stale NFSv4.1 leases when doing a mount"
* tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (24 commits)
NFSv4.1: Clear the old state by our client id before establishing a new lease
NFSv4: Fix a race in NFSv4.1 server trunking discovery
NFS: Don't write enable new pages while an invalidation is proceeding
NFS: Fix a regression in the read() syscall
NFSv4: Ensure we skip delegations that are already being returned
NFSv4: Pin the superblock while we're returning the delegation
NFSv4: Ensure we honour NFS_DELEGATION_RETURNING in nfs_inode_set_delegation()
NFSv4: Ensure that we don't reap a delegation that is being returned
NFS: Fix stateid used for NFS v4 closes
NFSv4: Don't call put_rpccred() under the rcu_read_lock()
NFS: Don't require a filehandle to refresh the inode in nfs_prime_dcache()
NFSv3: Use the readdir fileid as the mounted-on-fileid
NFS: Don't invalidate a submounted dentry in nfs_prime_dcache()
NFSv4: Set a barrier in the update_changeattr() helper
NFS: Fix nfs_post_op_update_inode() to set an attribute barrier
NFS: Remove size hack in nfs_inode_attrs_need_update()
NFSv4: Add attribute update barriers to delegreturn and pNFS layoutcommit
NFS: Add attribute update barriers to NFS writebacks
NFS: Set an attribute barrier on all updates
NFS: Add attribute update barriers to nfs_setattr_update_inode()
...
Mathias Nyman [Fri, 6 Mar 2015 15:23:19 +0000 (17:23 +0200)]
xhci: Workaround for PME stuck issues in Intel xhci
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
xhci: fix reporting of 0-sized URBs in control endpoint
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Laura Abbott [Wed, 25 Feb 2015 22:14:57 +0000 (14:14 -0800)]
kernel/module.c: Update debug alignment after symtable generation
When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of
module sections are aligned up so appropriate permissions can
be applied. Adjusting for the symbol table may cause them to
become unaligned. Make sure to re-align the sizes afterward.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Laura Abbott [Wed, 25 Feb 2015 22:14:55 +0000 (14:14 -0800)]
arm64: Don't use is_module_addr in setting page attributes
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Filipe Manana [Sun, 1 Mar 2015 20:36:00 +0000 (20:36 +0000)]
Btrfs: fix data loss in the fast fsync path
When using the fast file fsync code path we can miss the fact that new
writes happened since the last file fsync and therefore return without
waiting for the IO to finish and write the new extents to the fsync log.
Here's an example scenario where the fsync will miss the fact that new
file data exists that wasn't yet durably persisted:
1. fs_info->last_trans_committed == N - 1 and current transaction is
transaction N (fs_info->generation == N);
2. do a buffered write;
3. fsync our inode, this clears our inode's full sync flag, starts
an ordered extent and waits for it to complete - when it completes
at btrfs_finish_ordered_io(), the inode's last_trans is set to the
value N (via btrfs_update_inode_fallback -> btrfs_update_inode ->
btrfs_set_inode_last_trans);
4. transaction N is committed, so fs_info->last_trans_committed is now
set to the value N and fs_info->generation remains with the value N;
5. do another buffered write, when this happens btrfs_file_write_iter
sets our inode's last_trans to the value N + 1 (that is
fs_info->generation + 1 == N + 1);
6. transaction N + 1 is started and fs_info->generation now has the
value N + 1;
7. transaction N + 1 is committed, so fs_info->last_trans_committed
is set to the value N + 1;
8. fsync our inode - because it doesn't have the full sync flag set,
we only start the ordered extent, we don't wait for it to complete
(only in a later phase) therefore its last_trans field has the
value N + 1 set previously by btrfs_file_write_iter(), and so we
have:
Which made us not log the last buffered write and exit the fsync
handler immediately, returning success (0) to user space and resulting
in data loss after a crash.
This can actually be triggered deterministically and the following excerpt
from a testcase I made for xfstests triggers the issue. It moves a dummy
file across directories and then fsyncs the old parent directory - this
is just to trigger a transaction commit, so moving files around isn't
directly related to the issue but it was chosen because running 'sync' for
example does more than just committing the current transaction, as it
flushes/waits for all file data to be persisted. The issue can also happen
at random periods, since the transaction kthread periodicaly commits the
current transaction (about every 30 seconds by default).
The body of the test is:
# Create our main test file 'foo', the one we check for data loss.
# By doing an fsync against our file, it makes btrfs clear the 'needs_full_sync'
# bit from its flags (btrfs inode specific flags).
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0 8K" \
-c "fsync" $SCRATCH_MNT/foo | _filter_xfs_io
# Now create one other file and 2 directories. We will move this second file
# from one directory to the other later because it forces btrfs to commit its
# currently open transaction if we fsync the old parent directory. This is
# necessary to trigger the data loss bug that affected btrfs.
mkdir $SCRATCH_MNT/testdir_1
touch $SCRATCH_MNT/testdir_1/bar
mkdir $SCRATCH_MNT/testdir_2
# Make sure everything is durably persisted.
sync
# Write more 8Kb of data to our file.
$XFS_IO_PROG -c "pwrite -S 0xbb 8K 8K" $SCRATCH_MNT/foo | _filter_xfs_io
# Move our 'bar' file into a new directory.
mv $SCRATCH_MNT/testdir_1/bar $SCRATCH_MNT/testdir_2/bar
# Fsync our first directory. Because it had a file moved into some other
# directory, this made btrfs commit the currently open transaction. This is
# a condition necessary to trigger the data loss bug.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir_1
# Now fsync our main test file. If the fsync succeeds, we expect the 8Kb of
# data we wrote previously to be persisted and available if a crash happens.
# This did not happen with btrfs, because of the transaction commit that
# happened when we fsynced the parent directory.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Now check that all data we wrote before are available.
echo "File content after log replay:"
od -t x1 $SCRATCH_MNT/foo
status=0
exit
The expected golden output for the test, which is what we get with this
fix applied (or when running against ext3/4 and xfs), is:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
* 0040000
Without this fix applied, the output shows the test file does not have
the second 8Kb extent that we successfully fsynced:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000
So fix this by skipping the fsync only if we're doing a full sync and
if the inode's last_trans is <= fs_info->last_trans_committed, or if
the inode is already in the log. Also remove setting the inode's
last_trans in btrfs_file_write_iter since it's useless/unreliable.
Also because btrfs_file_write_iter no longer sets inode->last_trans to
fs_info->generation + 1, don't set last_trans to 0 if we bail out and don't
bail out if last_trans is 0, otherwise something as simple as the following
example wouldn't log the second write on the last fsync:
1. write to file
2. fsync file
3. fsync file
|--> btrfs_inode_in_log() returns true and it set last_trans to 0
4. write to file
|--> btrfs_file_write_iter() no longers sets last_trans, so it
remained with a value of 0
5. fsync
|--> inode->last_trans == 0, so it bails out without logging the
second write
A test case for xfstests will be sent soon.
CC: <stable@vger.kernel.org> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Mark Rutland [Wed, 4 Mar 2015 20:00:40 +0000 (20:00 +0000)]
genirq / PM: describe IRQF_COND_SUSPEND
With certain restrictions it is possible for a wakeup device to share
an IRQ with an IRQF_NO_SUSPEND user, and the warnings introduced by
commit cab303be91dc47942bc25de33dc1140123540800 are spurious. The new
IRQF_COND_SUSPEND flag allows drivers to tell the core when these
restrictions are met, allowing spurious warnings to be silenced.
This patch documents how IRQF_COND_SUSPEND is expected to be used,
updating some of the text now made invalid by its addition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boris BREZILLON [Mon, 2 Mar 2015 09:18:18 +0000 (10:18 +0100)]
tty: serial: atmel: rework interrupt and wakeup handling
The IRQ line connected to the DBGU UART is often shared with a timer device
which request the IRQ with IRQF_NO_SUSPEND.
Since the UART driver is correctly disabling IRQs when entering suspend
we can safely request the IRQ with IRQF_COND_SUSPEND so that irq core
will not complain about mixing IRQF_NO_SUSPEND and !IRQF_NO_SUSPEND.
Rework the interrupt handler to wake the system up when an interrupt
happens on the DEBUG_UART while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boris BREZILLON [Mon, 2 Mar 2015 09:18:17 +0000 (10:18 +0100)]
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
The watchdog interrupt (only used when activating software watchdog)
shouldn't be suspended when entering suspend mode, because it is shared
with a timer device (which request the line with IRQF_NO_SUSPEND) and once
the watchdog "Mode Register" has been written, it cannot be changed (which
means we cannot disable the watchdog interrupt when entering suspend).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* suspend-to-idle:
cpuidle / sleep: Use broadcast timer for states that stop local timer
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
* acpi-resources:
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
PCI: versatile: Update for list_for_each_entry() API change
cpuidle / sleep: Use broadcast timer for states that stop local timer
Commit 381063133246 (PM / sleep: Re-implement suspend-to-idle handling)
overlooked the fact that entering some sufficiently deep idle states
by CPUs may cause their local timers to stop and in those cases it
is necessary to switch over to a broadcast timer prior to entering
the idle state. If the cpuidle driver in use does not provide
the new ->enter_freeze callback for any of the idle states, that
problem affects suspend-to-idle too, but it is not taken into account
after the changes made by commit 381063133246.
Fix that by changing the definition of cpuidle_enter_freeze() and
re-arranging of the code in cpuidle_idle_call(), so the former does
not call cpuidle_enter() any more and the fallback case is handled
by cpuidle_idle_call() directly.
Fixes: 381063133246 (PM / sleep: Re-implement suspend-to-idle handling) Reported-and-tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
f31a9f7c7169 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area")
introduced alternative instructions for XSAVES/XRSTORS and commit:
adb9d526e982 ("x86/xsaves: Add xsaves and xrstors support for booting time")
added support for the XSAVES/XRSTORS instructions at boot time.
Unfortunately both failed to properly protect them against faulting:
The 'xstate_fault' macro will use the closest label named '1'
backward and that ends up in the .altinstr_replacement section
rather than in .text. This means that the kernel will never find
in the __ex_table the .text address where this instruction might
fault, leading to serious problems if userspace manages to
trigger the fault.
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: Jamie Iles <jamie.iles@oracle.com>
[ Improved the changelog, fixed some whitespace noise. ] Acked-by: Borislav Petkov <bp@alien8.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@vger.kernel.org> Cc: Allan Xavier <mr.a.xavier@gmail.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: adb9d526e982 ("x86/xsaves: Add xsaves and xrstors support for booting time") Fixes: f31a9f7c7169 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area") Signed-off-by: Ingo Molnar <mingo@kernel.org>
Robert Jarzmik [Sun, 15 Feb 2015 18:49:16 +0000 (19:49 +0100)]
dmaengine: mmp_pdma: fix warning about slave caps
Fix the dmaengine complaint about missing slave caps :
- declare the available bus widths
- declare the available transfer types
- declare the residue calculation type
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Shevchenko [Thu, 5 Mar 2015 15:24:04 +0000 (17:24 +0200)]
x86/intel/quark: Select COMMON_CLK
The commit 8bbc2a135b63 ("x86/intel/quark: Add Intel Quark
platform support") introduced a minimal support of Intel Quark
SoC. That allows to use core parts of the SoC. However, the SPI,
I2C, and GPIO drivers can't be selected by kernel configuration
because they depend on COMMON_CLK. The patch adds a COMMON_CLK
selection to the platfrom definition to allow user choose the drivers.
The commit fb93f520e (dmaengine: qcom_bam_dma: Generalize BAM
register offset calculations) wrongly populated base offsets
for event registers for bam v1.4.
Merge tag 'usb-serial-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.0-rc3
Here are a few fixes for reported problems including a usb-debug device
buffer overflow, potential use-after-free on failed probe, and a couple
of issues with the USB console.
Jie Yang [Thu, 5 Mar 2015 06:08:08 +0000 (14:08 +0800)]
dmaengine: dw: don't handle interrupt when dmaengine is not used
When dma controller is not used by any user and set off,
we should disble interrupt handler, at least the interrupt
reset part, for some subsystem, e.g. ADSP, may use the
dma in its own logic, here reset the interrupt may make
this subsystem work abnormally.
Signed-off-by: Jie Yang <yang.jie@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
thermal: Make sysfs attributes of cooling devices default attributes
Default attributes are created when the device is registered. Attributes
created after device registration can lead to race conditions, where user space
(e.g. udev) sees the device but not the attributes.
Andy Lutomirski [Thu, 5 Mar 2015 00:09:44 +0000 (01:09 +0100)]
x86/asm/entry/64: Remove a bogus 'ret_from_fork' optimization
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rob Clark [Mon, 2 Mar 2015 21:19:06 +0000 (16:19 -0500)]
drm/msm: kexec fixes
In kexec environment, we are more likely to encounter irq's already
enabled from previous environment. At which point we find that writes
to disable/clear pending irq's are slightly less than useless without
first enabling clocks.
TODO: full blown state read-in so kexec'd kernel can inherit the mode
already setup.
Rob Clark [Tue, 24 Feb 2015 19:47:57 +0000 (14:47 -0500)]
drm/msm/mdp5: fix cursor ROI
If cursor is set near the edge of the screen, it is not valid to use the
new cursor width/height as the ROI dimensions. Split out the ROI calc
and use it both cursor_set and cursor_move.
Stephane Viau [Fri, 20 Feb 2015 21:30:56 +0000 (16:30 -0500)]
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
When a CRTC is disabled, no CTL is allocated to it (CRTC->ctl == NULL);
in that case we should not try to FLUSH registers and do nothing instead.
This can happen when we try to move a cursor but the CRTC's CTL
(CONTROL) has not been allocated yet (inactive CRTC).
It can also happens when we .atomic_check()/.atomic_flush() on a
disabled CRTC.
A CTL needs to be kept as long as the CRTC is alive. Releasing it
after the last VBlank is safer than in .atomic_flush().
Signed-off-by: Stephane Viau <sviau@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Stephane Viau [Fri, 20 Feb 2015 17:40:58 +0000 (12:40 -0500)]
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
Commit 0b776d457b94 ("drm/msm: fix fallout of atomic dpms
changes") has a typo in both mdp5_encoder_helper_funcs and
mdp5_crtc_helper_funcs definitions:
.dpms entry should be replaced by .disable and .enable
Also fixed a typo in mdp5_encoder_enable().
Note that these typos are only present for MDP5. MDP4 is fine.
Signed-off-by: Stephane Viau <sviau@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com>
Dave Airlie [Wed, 4 Mar 2015 23:21:51 +0000 (09:21 +1000)]
Merge branch 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Radeon fixes for 4.0:
- Fix some fallout from the audio rework
- Fix a possible oops in the CS ioctl
- Fix interlaced modes on DCE8
- Do a posting read in irq_set callbacks to make sure
interrupts are properly flushed through the pci bridge
* 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
radeon/audio: fix whitespace
drm/radeon: adjust audio callback order
drm/radeon: properly set dto for dp on DCE4/5
drm/radeon/audio: update EDID derived fields in modeset
drm/radeon: don't toggle audio state in modeset
drm/radeon/audio: set mute around state setup
drm/radeon: assign pin in detect
drm/radeon: fix the audio dpms callbacks
Alex Deucher [Wed, 4 Mar 2015 05:18:38 +0000 (00:18 -0500)]
drm/ttm: device address space != CPU address space
We need to store device offsets in 64 bit as the device
address space may be larger than the CPU's.
Fixes GPU init failures on radeons with 4GB or more of
vram on 32 bit kernels. We put vram at the start of the
GPU's address space so the gart aperture starts at 4 GB
causing all GPU addresses in the gart aperture to get
truncated.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: thellstrom@vmware.com Acked-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Thierry Reding [Fri, 23 Jan 2015 08:05:06 +0000 (09:05 +0100)]
drm/mm: Support 4 GiB and larger ranges
The current implementation is limited by the number of addresses that
fit into an unsigned long. This causes problems on 32-bit Tegra where
unsigned long is 32-bit but drm_mm is used to manage an IOVA space of
4 GiB. Given the 32-bit limitation, the range is limited to 4 GiB - 1
(or 4 GiB - 4 KiB for page granularity).
This commit changes the start and size of the range to be an unsigned
64-bit integer, thus allowing much larger ranges to be supported.
[airlied: fix i915 warnings and coloring callback]
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
fixupo
Jeff Layton [Wed, 4 Mar 2015 22:34:32 +0000 (17:34 -0500)]
locks: fix fasync_struct memory leak in lease upgrade/downgrade handling
Commit 8634b51f6ca2 (locks: convert lease handling to file_lock_context)
introduced a regression in the handling of lease upgrade/downgrades.
In the event that we already have a lease on a file and are going to
either upgrade or downgrade it, we skip doing any list insertion or
deletion and simply re-call lm_setup on the existing lease.
As of commit 8634b51f6ca2 however, we end up calling lm_setup on the
lease that was passed in, instead of on the existing lease. This causes
us to leak the fasync_struct that was allocated in the event that there
was not already an existing one (as it always appeared that there
wasn't one).
Fixes: 8634b51f6ca2 (locks: convert lease handling to file_lock_context) Reported-and-Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Linus Torvalds [Wed, 4 Mar 2015 22:19:48 +0000 (14:19 -0800)]
Merge tag 'ecryptfs-4.0-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs fixes from Tyler Hicks:
"Fixes for proper ioctl handling and an untriggerable buffer overflow
- The eCryptfs ioctl handling functions should only pass known-good
ioctl commands to the lower filesystem
- A static checker found a potential buffer overflow. Upon
inspection, it is not triggerable due to input validation performed
on the mount parameters"
* tag 'ecryptfs-4.0-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: don't pass fs-specific ioctl commands through
eCryptfs: ensure copy to crypt_stat->cipher does not overrun
Boris BREZILLON [Mon, 2 Mar 2015 09:18:16 +0000 (10:18 +0100)]
clk: at91: implement suspend/resume for the PMC irqchip
The irq line used by the PMC block is shared with several peripherals
including the init timer which is registering its handler with
IRQF_NO_SUSPEND.
Implement the appropriate suspend/resume callback for the PMC irqchip,
and inform irq core that PMC irq handler can be safely called while
the system is suspended by setting IRQF_COND_SUSPEND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boris BREZILLON [Mon, 2 Mar 2015 09:18:15 +0000 (10:18 +0100)]
rtc: at91rm9200: rework wakeup and interrupt handling
The IRQ line used by the RTC device is usually shared with the system
timer (PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we
should expect being called in suspended state, and properly wake the
system up when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boris BREZILLON [Mon, 2 Mar 2015 09:18:14 +0000 (10:18 +0100)]
rtc: at91sam9: rework wakeup and interrupt handling
The IRQ line used by the RTC device is usually shared with the system timer
(PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we should
expect being called in suspended state, and properly wake the system up
when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boris BREZILLON [Mon, 2 Mar 2015 09:18:13 +0000 (10:18 +0100)]
PM / wakeup: export pm_system_wakeup symbol
Export pm_system_wakeup function to allow irq handlers to deal with system
wakeup.
This is needed for shared IRQ lines where one of the handler is registered
with IRQF_NO_SUSPEND, while the other ones want to configure it as a wakeup
source.
In this specific case, irq core does not handle the wakeup process and
leave the decision to each irq handler.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
projects / mirror_ubuntu-jammy-kernel.git / log