Thomas Falcon [Thu, 22 Feb 2018 00:18:30 +0000 (18:18 -0600)]
ibmvnic: Fix early release of login buffer
The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.
Fixes: 34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks") Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 21 Feb 2018 22:24:59 +0000 (09:24 +1100)]
net/smc9194: Remove bogus CONFIG_MAC reference
AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.
Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 21 Feb 2018 19:00:54 +0000 (11:00 -0800)]
net: ipv4: Set addr_type in hash_keys for forwarded case
The result of the skb flow dissect is copied from keys to hash_keys to
ensure only the intended data is hashed. The original L4 hash patch
overlooked setting the addr_type for this case; add it.
Fixes: bf4e0a3db97eb ("net: ipv4: add support for ECMP hash policy choice") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: David Ahern <dsahern@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Feb 2018 14:43:03 +0000 (06:43 -0800)]
tcp_bbr: better deal with suboptimal GSO
BBR uses tcp_tso_autosize() in an attempt to probe what would be the
burst sizes and to adjust cwnd in bbr_target_cwnd() with following
gold formula :
/* Allow enough full-sized skbs in flight to utilize end systems. */
cwnd += 3 * bbr->tso_segs_goal;
But GSO can be lacking or be constrained to very small
units (ip link set dev ... gso_max_segs 2)
What we really want is to have enough packets in flight so that both
GSO and GRO are efficient.
So in the case GSO is off or downgraded, we still want to have the same
number of packets in flight as if GSO/TSO was fully operational, so
that GRO can hopefully be working efficiently.
To fix this issue, we make tcp_tso_autosize() unaware of
sk->sk_gso_max_segs
Only tcp_tso_segs() has to enforce the gso_max_segs limit.
Tested:
ethtool -K eth0 tso off gso off
tc qd replace dev eth0 root pfifo_fast
Before patch:
for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
691 (ss -temoi shows cwnd is stuck around 6 )
667
651
631
517
After patch :
# for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
1733 (ss -temoi shows cwnd is around 386 )
1778
1746
1781
1718
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Feb 2018 05:42:26 +0000 (21:42 -0800)]
smsc75xx: fix smsc75xx_set_features()
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Before, if cb->start() failed, the module reference would never be put,
because cb->cb_running is intentionally false at this point. Users are
generally annoyed by this because they can no longer unload modules that
leak references. Also, it may be possible to tediously wrap a reference
counter back to zero, especially since module.c still uses atomic_inc
instead of refcount_inc.
This patch expands the error path to simply call module_put if
cb->start() fails.
Fixes: 41c87425a1ac ("netlink: do not set cb_running if dump's start() errs") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a memory leak in LPM trie's map_free() callback function, where
the trie structure itself was not freed since initial implementation.
Also a synchronize_rcu() was needed in order to wait for outstanding
programs accessing the trie to complete, from Yonghong.
2) Fix sock_map_alloc()'s error path in order to correctly propagate
the -EINVAL error in case of too large allocation requests. This
was just recently introduced when fixing close hooks via ULP layer,
fix from Eric.
3) Do not use GFP_ATOMIC in __cpu_map_entry_alloc(). Reason is that this
will not work with the recent __ptr_ring_init_queue_alloc() conversion
to kvmalloc_array(), where in case of fallback to vmalloc() that GFP
flag is invalid, from Jason.
4) Fix two recent syzkaller warnings: i) fix bpf_prog_array_copy_to_user()
when a prog query with a big number of ids was performed where we'd
otherwise trigger a warning from allocator side, ii) fix a missing
mlock precharge on arraymaps, from Daniel.
5) Two fixes for bpftool in order to avoid breaking JSON output when used
in batch mode, from Quentin.
6) Move a pr_debug() in libbpf in order to avoid having an otherwise
uninitialized variable in bpf_program__reloc_text(), from Jeremy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Feb 2018 20:09:30 +0000 (15:09 -0500)]
Merge branch 'virtio_net-XDP-fixes'
Jesper Dangaard Brouer says:
====================
virtio_net: several bugs in XDP code for driver virtio_net
The virtio_net driver actually violates the original memory model of
XDP causing hard to debug crashes. Per request of John Fastabend,
instead of removing the XDP feature I'm fixing as much as possible.
While testing virtio_net with XDP_REDIRECT I found 4 different bugs.
Patch-1: not enough tail-room for build_skb in receive_mergeable()
only option is to disable XDP_REDIRECT in receive_mergeable()
Patch-2: XDP in receive_small() basically never worked (check wrong flag)
Patch-3: fix memory leak for XDP_REDIRECT in error cases
Patch-4: avoid crash when ndo_xdp_xmit is called on dev not ready for XDP
In the longer run, we should consider introducing a separate receive
function when attaching an XDP program, and also change the memory
model to be compatible with XDP when attaching an XDP prog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net: fix ndo_xdp_xmit crash towards dev not ready for XDP
When a driver implements the ndo_xdp_xmit() function, there is
(currently) no generic way to determine whether it is safe to call.
It is e.g. unsafe to call the drivers ndo_xdp_xmit, if it have not
allocated the needed XDP TX queues yet. This is the case for
virtio_net, which first allocates the XDP TX queues once an XDP/bpf
prog is attached (in virtnet_xdp_set()).
Thus, a crash will occur for virtio_net when redirecting to another
virtio_net device's ndo_xdp_xmit, which have not attached a XDP prog.
The sample xdp_redirect_map tries to attach a dummy XDP prog to take
this into account, but it can also easily fail if the virtio_net (or
actually underlying vhost driver) have not allocated enough extra
queues for the device.
Allocating more queue this is currently a manual config.
Hint for libvirt XML add:
The solution in this patch is to check that the device have loaded an
XDP/bpf prog before proceeding. This is similar to the check
performed in driver ixgbe.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_REDIRECT calling xdp_do_redirect() can fail for multiple reasons
(which can be inspected by tracepoints). The current semantics is that
on failure the driver calling xdp_do_redirect() must handle freeing or
recycling the page associated with this frame. This can be seen as an
optimization, as drivers usually have an optimized XDP_DROP code path
for frame recycling in place already.
The virtio_net driver didn't handle when xdp_do_redirect() failed.
This caused a memory leak as the page refcnt wasn't decremented on
failures.
The function __virtnet_xdp_xmit() did handle one type of failure,
when the xmit queue virtqueue_add_outbuf() is full, which "hides"
releasing a refcnt on the page. Instead the function __virtnet_xdp_xmit()
must follow API of xdp_do_redirect(), which on errors leave it up to
the caller to free the page, of the failed send operation.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring virtio_net to use the code path 'receive_small()',
in-order to get correct XDP_REDIRECT support, I discovered TCP packets
would get silently dropped when loading an XDP program action XDP_PASS.
The bug seems to be that receive_small() when XDP is loaded check that
hdr->hdr.flags is zero, which seems wrong as hdr.flags contains the
flags VIRTIO_NET_HDR_F_* :
#define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 /* Use csum_start, csum_offset */
#define VIRTIO_NET_HDR_F_DATA_VALID 2 /* Csum is valid */
TCP got dropped as it had the VIRTIO_NET_HDR_F_DATA_VALID flag set.
The flags that are relevant here are the VIRTIO_NET_HDR_GSO_* flags
stored in hdr->hdr.gso_type. Thus, the fix is just check that none of
the gso_type flags have been set.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net: disable XDP_REDIRECT in receive_mergeable() case
The virtio_net code have three different RX code-paths in receive_buf().
Two of these code paths can handle XDP, but one of them is broken for
at least XDP_REDIRECT.
Function(1): receive_big() does not support XDP.
Function(2): receive_small() support XDP fully and uses build_skb().
Function(3): receive_mergeable() broken XDP_REDIRECT uses napi_alloc_skb().
The simple explanation is that receive_mergeable() is broken because
it uses napi_alloc_skb(), which violates XDP given XDP assumes packet
header+data in single page and enough tail room for skb_shared_info.
The longer explaination is that receive_mergeable() tries to
work-around and satisfy these XDP requiresments e.g. by having a
function xdp_linearize_page() that allocates and memcpy RX buffers
around (in case packet is scattered across multiple rx buffers). This
does currently satisfy XDP_PASS, XDP_DROP and XDP_TX (but only because
we have not implemented bpf_xdp_adjust_tail yet).
The XDP_REDIRECT action combined with cpumap is broken, and cause hard
to debug crashes. The main issue is that the RX packet does not have
the needed tail-room (SKB_DATA_ALIGN(skb_shared_info)), causing
skb_shared_info to overlap the next packets head-room (in which cpumap
stores info).
Reproducing depend on the packet payload length and if RX-buffer size
happened to have tail-room for skb_shared_info or not. But to make
this even harder to troubleshoot, the RX-buffer size is runtime
dynamically change based on an Exponentially Weighted Moving Average
(EWMA) over the packet length, when refilling RX rings.
This patch only disable XDP_REDIRECT support in receive_mergeable()
case, because it can cause a real crash.
IMHO we should consider NOT supporting XDP in receive_mergeable() at
all, because the principles behind XDP are to gain speed by (1) code
simplicity, (2) sacrificing memory and (3) where possible moving
runtime checks to setup time. These principles are clearly being
violated in receive_mergeable(), that e.g. runtime track average
buffer size to save memory consumption.
In the longer run, we should consider introducing a separate receive
function when attaching an XDP program, and also change the memory
model to be compatible with XDP when attaching an XDP prog.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains large batch with Netfilter fixes for
your net tree, mostly due to syzbot report fixups and pr_err()
ratelimiting, more specifically, they are:
1) Get rid of superfluous unnecessary check in x_tables before vmalloc(),
we don't hit BUG there anymore, patch from Michal Hock, suggested by
Andrew Morton.
2) Race condition in proc file creation in ipt_CLUSTERIP, from Cong Wang.
3) Drop socket lock that results in circular locking dependency, patch
from Paolo Abeni.
4) Drop packet if case of malformed blob that makes backpointer jump
in x_tables, from Florian Westphal.
5) Fix refcount leak due to race in ipt_CLUSTERIP in
clusterip_config_find_get(), from Cong Wang.
6) Several patches to ratelimit pr_err() for x_tables since this can be
a problem where CAP_NET_ADMIN semantics can protect us in untrusted
namespace, from Florian Westphal.
7) Missing .gitignore update for new autogenerated asn1 state machine
for the SNMP NAT helper, from Zhu Lingshan.
8) Missing timer initialization in xt_LED, from Paolo Abeni.
9) Do not allow negative port range in NAT, also from Paolo.
10) Lock imbalance in the xt_hashlimit rate match mode, patch from
Eric Dumazet.
11) Initialize workqueue before timer in the idletimer match,
from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Kapl [Mon, 19 Feb 2018 20:32:51 +0000 (21:32 +0100)]
net: sched: report if filter is too large to dump
So far, if the filter was too large to fit in the allocated skb, the
kernel did not return any error and stopped dumping. Modify the dumper
so that it returns -EMSGSIZE when a filter fails to dump and it is the
first filter in the skb. If we are not first, we will get a next chance
with more room.
I understand this is pretty near to being an API change, but the
original design (silent truncation) can be considered a bug.
Note: The error case can happen pretty easily if you create a filter
with 32 actions and have 4kb pages. Also recent versions of iproute try
to be clever with their buffer allocation size, which in turn leads to
Signed-off-by: Roman Kapl <code@rkapl.cz> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Tue, 6 Feb 2018 08:52:19 +0000 (10:52 +0200)]
net/mlx5: Fix error handling when adding flow rules
If building match list or adding existing fg fails when
node is locked, function returned without unlocking it.
This happened if node version changed or adding existing fg
returned with EAGAIN after jumping to search_again_locked label.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5: E-Switch, Fix drop counters use before creation
First use of drop counters happens in esw_apply_vport_conf function,
while they are allocated later in the flow. Fix that by moving
esw_vport_create_drop_counters function to be called before the first use.
Daniel Jurgens [Fri, 2 Feb 2018 15:32:53 +0000 (09:32 -0600)]
net/mlx5: Use 128B cacheline size for 128B or larger cachelines
The adapter uses the cache_line_128byte setting to set the bounds for
end padding. On systems where the cacheline size is greater than 128B
use 128B instead of the default of 64B. This results in fewer partial
cacheline writes. There's a 50% chance it will pad to the end of a 256B
cache line vs only 25% when using 64B.
Fixes: f32f5bd2eb7e ("net/mlx5: Configure cache line size for start and end padding") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Thu, 25 Jan 2018 16:00:41 +0000 (18:00 +0200)]
net/mlx5e: Specify numa node when allocating drop rq
When allocating a drop rq, no numa node is explicitly set which means
allocations are done on node zero. This is not necessarily the nearest
numa node to the HCA, and even worse, might even be a memoryless numa
node.
Choose the numa_node given to us by the pci device in order to properly
allocate the coherent dma memory instead of assuming zero is valid.
Fixes: 556dd1b9c313 ("net/mlx5e: Set drop RQ's necessary parameters only") Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Mon, 1 Jan 2018 13:19:51 +0000 (13:19 +0000)]
net/mlx5e: Eliminate build warnings on no previous prototype
Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:
[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Eran Ben Elisha [Thu, 25 Jan 2018 09:18:09 +0000 (11:18 +0200)]
net/mlx5e: Verify inline header size do not exceed SKB linear size
Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.
Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.
This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.
Fixes: 6aace17e64f4 ("net/mlx5e: Fix inline header size for small packets") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Wed, 20 Dec 2017 06:48:24 +0000 (08:48 +0200)]
net/mlx5e: Fix TCP checksum in LRO buffers
When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed. We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.
Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).
This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.
It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.
Jeremy Cline [Tue, 20 Feb 2018 01:00:07 +0000 (01:00 +0000)]
tools/libbpf: Avoid possibly using uninitialized variable
Fixes a GCC maybe-uninitialized warning introduced by 48cca7e44f9f.
"text" is only initialized inside the if statement so only print debug
info there.
Fixes: 48cca7e44f9f ("libbpf: add support for bpf_call") Signed-off-by: Jeremy Cline <jeremy@jcline.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Thomas Falcon [Tue, 20 Feb 2018 02:12:57 +0000 (20:12 -0600)]
ibmvnic: Check for NULL skb's in NAPI poll routine
After introduction of commit d0869c0071e4, there were some instances of
RX queue entries from a previous session (before the device was closed
and reopened) returned to the NAPI polling routine. Since the corresponding
socket buffers were freed, this resulted in a panic on reopen. Include
a check for a NULL skb here to avoid this.
Fixes: d0869c0071e4 ("ibmvnic: Clean RX pool buffers during device close") Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Prevent index integer overflow in ptr_ring, from Jason Wang.
2) Program mvpp2 multicast filter properly, from Mikulas Patocka.
3) The bridge brport attribute file is write only and doesn't have a
->show() method, don't blindly invoke it. From Xin Long.
4) Inverted mask used in genphy_setup_forced(), from Ingo van Lil.
5) Fix multiple definition issue with if_ether.h UAPI header, from
Hauke Mehrtens.
6) Fix GFP_KERNEL usage in atomic in RDS protocol code, from Sowmini
Varadhan.
7) Revert XDP redirect support from thunderx driver, it is not
implemented properly. From Jesper Dangaard Brouer.
8) Fix missing RTNL protection across some tipc operations, from Ying
Xue.
9) Return the correct IV bytes in the TLS getsockopt code, from Boris
Pismenny.
10) Take tclassid into consideration properly when doing FIB rule
matching. From Stefano Brivio.
11) cxgb4 device needs more PCI VPD quirks, from Casey Leedom.
12) TUN driver doesn't align frags properly, and we can end up doing
unaligned atomics on misaligned metadata. From Eric Dumazet.
13) Fix various crashes found using DEBUG_PREEMPT in rmnet driver, from
Subash Abhinov Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
tg3: APE heartbeat changes
mlxsw: spectrum_router: Do not unconditionally clear route offload indication
net: qualcomm: rmnet: Fix possible null dereference in command processing
net: qualcomm: rmnet: Fix warning seen with 64 bit stats
net: qualcomm: rmnet: Fix crash on real dev unregistration
sctp: remove the left unnecessary check for chunk in sctp_renege_events
rxrpc: Work around usercopy check
tun: fix tun_napi_alloc_frags() frag allocator
udplite: fix partial checksum initialization
skbuff: Fix comment mis-spelling.
dn_getsockoptdecnet: move nf_{get/set}sockopt outside sock lock
PCI/cxgb4: Extend T3 PCI quirk to T4+ devices
cxgb4: fix trailing zero in CIM LA dump
cxgb4: free up resources of pf 0-3
fib_semantics: Don't match route with mismatching tclassid
NFC: llcp: Limit size of SDP URI
tls: getsockopt return record sequence number
tls: reset the crypto info if copy_from_user fails
tls: retrun the correct IV in getsockopt
docs: segmentation-offloads.txt: add SCTP info
...
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com> Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 17 Feb 2018 03:36:28 +0000 (19:36 -0800)]
netfilter: IDLETIMER: be syzkaller friendly
We had one report from syzkaller [1]
First issue is that INIT_WORK() should be done before mod_timer()
or we risk timer being fired too soon, even with a 1 second timer.
Second issue is that we need to reject too big info->timeout
to avoid overflows in msecs_to_jiffies(info->timeout * 1000), or
risk looping, if result after overflow is 0.
[1]
WARNING: CPU: 1 PID: 5129 at kernel/workqueue.c:1444 __queue_work+0xdf4/0x1230 kernel/workqueue.c:1444
Kernel panic - not syncing: panic_on_warn set ...
Ido Schimmel [Fri, 16 Feb 2018 23:30:44 +0000 (00:30 +0100)]
mlxsw: spectrum_router: Do not unconditionally clear route offload indication
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89fe7 ("mlxsw: spectrum_router: Provide offload indication using nexthop flags") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Tested-by: Alexander Petrovskiy <alexpe@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Fix possible null dereference in command processing
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c45760 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 192c4b5d48f2 ("net: qualcomm: rmnet: Add support for 64 bit stats") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Fix crash on real dev unregistration
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
Linus Torvalds [Sun, 18 Feb 2018 20:56:41 +0000 (12:56 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Linus Torvalds [Sun, 18 Feb 2018 20:38:40 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Linus Torvalds [Sat, 17 Feb 2018 18:20:47 +0000 (10:20 -0800)]
Merge tag 'for-linus-20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
Linus Torvalds [Sat, 17 Feb 2018 18:08:28 +0000 (10:08 -0800)]
Merge tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
Linus Torvalds [Sat, 17 Feb 2018 18:06:13 +0000 (10:06 -0800)]
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
Linus Torvalds [Sat, 17 Feb 2018 17:48:26 +0000 (09:48 -0800)]
Merge tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
Linus Torvalds [Sat, 17 Feb 2018 17:46:18 +0000 (09:46 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
Linus Torvalds [Sat, 17 Feb 2018 17:16:09 +0000 (09:16 -0800)]
Merge tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
pvcalls-front: introduce a per sock_mapping refcount
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Joao Martins [Fri, 2 Feb 2018 17:42:33 +0000 (17:42 +0000)]
xenbus: track caller request id
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Robin Murphy [Fri, 16 Feb 2018 17:04:23 +0000 (17:04 +0000)]
arm64: cputype: Silence Sparse warnings
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Xin Long [Fri, 16 Feb 2018 09:18:33 +0000 (17:18 +0800)]
sctp: remove the left unnecessary check for chunk in sctp_renege_events
Commit fb23403536ea ("sctp: remove the useless check in
sctp_renege_events") forgot to remove another check for
chunk in sctp_renege_events.
Dan found this when doing a static check.
This patch is to remove that check, and also to merge
two checks into one 'if statement'.
Fixes: fb23403536ea ("sctp: remove the useless check in sctp_renege_events") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 15 Feb 2018 22:59:00 +0000 (22:59 +0000)]
rxrpc: Work around usercopy check
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 15 Feb 2018 22:47:15 +0000 (14:47 -0800)]
tun: fix tun_napi_alloc_frags() frag allocator
<Mark Rutland reported>
While fuzzing arm64 v4.16-rc1 with Syzkaller, I've been hitting a
misaligned atomic in __skb_clone:
atomic_inc(&(skb_shinfo(skb)->dataref));
where dataref doesn't have the required natural alignment, and the
atomic operation faults. e.g. i often see it aligned to a single
byte boundary rather than a four byte boundary.
AFAICT, the skb_shared_info is misaligned at the instant it's
allocated in __napi_alloc_skb() __napi_alloc_skb()
</end of report>
Problem is caused by tun_napi_alloc_frags() using
napi_alloc_frag() with user provided seg sizes,
leading to other users of this API getting unaligned
page fragments.
Since we would like to not necessarily add paddings or alignments to
the frags that tun_napi_alloc_frags() attaches to the skb, switch to
another page frag allocator.
As a bonus skb_page_frag_refill() can use GFP_KERNEL allocations,
meaning that we can not deplete memory reserves as easily.
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Thu, 15 Feb 2018 17:18:43 +0000 (20:18 +0300)]
udplite: fix partial checksum initialization
Since UDP-Lite is always using checksum, the following path is
triggered when calculating pseudo header for it:
udp4_csum_init() or udp6_csum_init()
skb_checksum_init_zero_check()
__skb_checksum_validate_complete()
The problem can appear if skb->len is less than CHECKSUM_BREAK. In
this particular case __skb_checksum_validate_complete() also invokes
__skb_checksum_complete(skb). If UDP-Lite is using partial checksum
that covers only part of a packet, the function will return bad
checksum and the packet will be dropped.
It can be fixed if we skip skb_checksum_init_zero_check() and only
set the required pseudo header checksum for UDP-Lite with partial
checksum before udp4_csum_init()/udp6_csum_init() functions return.
Fixes: ed70fcfcee95 ("net: Call skb_checksum_init in IPv4") Fixes: e4f45b7f40bd ("net: Call skb_checksum_init in IPv6") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 3f34cfae1238 ("netfilter: on sockopt() acquire sock lock
only in the required scope"), the caller of nf_{get/set}sockopt() must
not hold any lock, but, in such changeset, I forgot to cope with DECnet.
This commit addresses the issue moving the nf call outside the lock,
in the dn_{get,set}sockopt() with the same schema currently used by
ipv4 and ipv6. Also moves the unhandled sockopts of the end of the main
switch statements, to improve code readability.
Reported-by: Petr Vandrovec <petr@vandrovec.name> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198791#c2 Fixes: 3f34cfae1238 ("netfilter: on sockopt() acquire sock lock only in the required scope") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Casey Leedom [Thu, 15 Feb 2018 14:33:18 +0000 (20:03 +0530)]
PCI/cxgb4: Extend T3 PCI quirk to T4+ devices
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff88 ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794ca1 ("cxgb4: Set VPD size so we can read both VPD structures") Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Thu, 15 Feb 2018 12:50:01 +0000 (18:20 +0530)]
cxgb4: fix trailing zero in CIM LA dump
Set correct size of the CIM LA dump for T6.
Fixes: 27887bc7cb7f ("cxgb4: collect hardware LA dumps") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 15 Feb 2018 12:46:57 +0000 (18:16 +0530)]
cxgb4: free up resources of pf 0-3
free pf 0-3 resources, commit baf5086840ab ("cxgb4:
restructure VF mgmt code") erroneously removed the
code which frees the pf 0-3 resources, causing the
probe of pf 0-3 to fail in case of driver reload.
Fixes: baf5086840ab ("cxgb4: restructure VF mgmt code") Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 16 Feb 2018 20:22:33 +0000 (12:22 -0800)]
Merge tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few dma-mapping fixes for the fallout from the changes in rc1"
* tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping:
powerpc/macio: set a proper dma_coherent_mask
dma-mapping: fix a comment typo
dma-direct: comment the dma_direct_free calling convention
dma-direct: mark as is_phys
ia64: fix build failure with CONFIG_SWIOTLB
Stefano Brivio [Thu, 15 Feb 2018 08:46:03 +0000 (09:46 +0100)]
fib_semantics: Don't match route with mismatching tclassid
In fib_nh_match(), if output interface or gateway are passed in
the FIB configuration, we don't have to check next hops of
multipath routes to conclude whether we have a match or not.
However, we might still have routes with different realms
matching the same output interface and gateway configuration,
and this needs to cause the match to fail. Otherwise the first
route inserted in the FIB will match, regardless of the realms:
# ip route add 1.1.1.1 dev eth0 table 1234 realms 1/2
# ip route append 1.1.1.1 dev eth0 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev eth0 scope link realms 1/2
1.1.1.1 dev eth0 scope link realms 3/4
# ip route del 1.1.1.1 dev ens3 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev ens3 scope link realms 3/4
whereas route with realms 3/4 should have been deleted instead.
Explicitly check for fc_flow passed in the FIB configuration
(this comes from RTA_FLOW extracted by rtm_to_fib_config()) and
fail matching if it differs from nh_tclassid.
The handling of RTA_FLOW for multipath routes later in
fib_nh_match() is still needed, as we can have multiple RTA_FLOW
attributes that need to be matched against the tclassid of each
next hop.
v2: Check that fc_flow is set before discarding the match, so
that the user can still select the first matching rule by
not specifying any realm, as suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 14 Feb 2018 23:45:07 +0000 (15:45 -0800)]
NFC: llcp: Limit size of SDP URI
The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.
Fixes: d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Thu, 15 Feb 2018 11:14:56 +0000 (11:14 +0000)]
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
In many cases, page tables can be accessed concurrently by either another
CPU (due to things like fast gup) or by the hardware page table walker
itself, which may set access/dirty bits. In such cases, it is important
to use READ_ONCE/WRITE_ONCE when accessing page table entries so that
entries cannot be torn, merged or subject to apparent loss of coherence
due to compiler transformations.
Whilst there are some scenarios where this cannot happen (e.g. pinned
kernel mappings for the linear region), the overhead of using READ_ONCE
/WRITE_ONCE everywhere is minimal and makes the code an awful lot easier
to reason about. This patch consistently uses these macros in the arch
code, as well as explicitly namespacing pointers to page table entries
from the entries themselves by using adopting a 'p' suffix for the former
(as is sometimes used elsewhere in the kernel source).
Tested-by: Yury Norov <ynorov@caviumnetworks.com> Tested-by: Richard Ruigrok <rruigrok@codeaurora.org> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Feb 2018 17:26:18 +0000 (09:26 -0800)]
Merge tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few assorted fixes, some of them show up during fstests so I
gave them more testing"
* tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix use-after-free when cleaning up fs_devs with a single stale device
Btrfs: fix null pointer dereference when replacing missing device
btrfs: remove spurious WARN_ON(ref->count < 0) in find_parent_nodes
btrfs: Ignore errors from btrfs_qgroup_trace_extent_post
Btrfs: fix unexpected -EEXIST when creating new inode
Btrfs: fix use-after-free on root->orphan_block_rsv
Btrfs: fix btrfs_evict_inode to handle abnormal inodes correctly
Btrfs: fix extent state leak from tree log
Btrfs: fix crash due to not cleaning up tree log block's dirty bits
Btrfs: fix deadlock in run_delalloc_nocow
Linus Torvalds [Fri, 16 Feb 2018 17:23:36 +0000 (09:23 -0800)]
Merge tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix for DM core to properly propagate errors (avoids overriding
non-zero error with 0). This is particularly important given DM core's
increased use of chained bios"
* tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: correctly handle chained bios in dec_pending()
Linus Torvalds [Fri, 16 Feb 2018 17:20:00 +0000 (09:20 -0800)]
Merge tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- regression fix in keyboard support for Dell laptops
- prevent out-of-boundary write in WMI bus driver
- increase timeout to read functional key status on Lenovo laptops
* tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: Removed duplicates in DMI whitelist
platform/x86: dell-laptop: fix kbd_get_state's request value
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
platform/x86: wmi: fix off-by-one write in wmi_dev_probe()
Linus Torvalds [Fri, 16 Feb 2018 17:11:30 +0000 (09:11 -0800)]
Merge tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of usual suspects:
- a handful USB-audio and HD-audio device-specific quirks
- some trivial fixes for the new AC97 bus stuff
- another race fix in ALSA sequencer core"
* tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: PCI quirk for Fujitsu U7x7
ALSA: seq: Fix racy pool initializations
ALSA: usb: add more device quirks for USB DSD devices
ALSA: usb-audio: Fix UAC2 get_ctl request with a RANGE attribute
ALSA: ac97: Fix copy and paste typo in documentation
ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204
ALSA: ac97: kconfig: Remove select of undefined symbol AC97
ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform
ALSA: hda/realtek - Add headset mode support for Dell laptop
ALSA: hda - Fix headset mic detection problem for two Dell machines
Linus Torvalds [Fri, 16 Feb 2018 17:08:59 +0000 (09:08 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One nouveau regression fix, one AMD quirk and a full set of i915
fixes.
The i915 fixes are mostly for things caught by their CI system, main
ones being DSI panel fixes and GEM fixes"
* tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Make clock gate support conditional
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
drm/amdgpu: add new device to use atpx quirk
NeilBrown [Thu, 15 Feb 2018 09:00:15 +0000 (20:00 +1100)]
dm: correctly handle chained bios in dec_pending()
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org (v3.14+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Thomas Gleixner [Fri, 16 Feb 2018 14:47:26 +0000 (15:47 +0100)]
Merge tag 'irqchip-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.16-rc2 from Marc Zyngier
- A MIPS GIC fix for spurious, masked interrupts
- A fix for a subtle IPI bug in GICv3
- Do not probe GICv3 ITSs that are marked as disabled
- Multi-MSI support for GICv2m
- Various cleanups
Jaedon Shin [Mon, 12 Feb 2018 02:18:12 +0000 (11:18 +0900)]
irqchip/bcm: Remove hashed address printing
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Marc Zyngier [Tue, 6 Feb 2018 18:55:33 +0000 (18:55 +0000)]
irqchip/gic-v2m: Add PCI Multi-MSI support
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stephen Boyd [Thu, 1 Feb 2018 17:03:29 +0000 (09:03 -0800)]
irqchip/gic-v3: Ignore disabled ITS nodes
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com> Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org Acked-by: Will Deacon <will.deacon@arm.com>, Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nathan Fontenot [Fri, 16 Feb 2018 03:27:41 +0000 (21:27 -0600)]
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
Some versions of QEMU will produce an ibm,dynamic-reconfiguration-memory
node with a ibm,dynamic-memory property that is zero-filled. This
causes the drmem code to oops trying to parse this property.
The fix for this is to validate that the property does contain LMB
entries before trying to parse it and bail if the count is zero.
Oops: Kernel access of bad area, sig: 11 [#1]
DAR: 0000000000000010
NIP read_drconf_v1_cell+0x54/0x9c
LR read_drconf_v1_cell+0x48/0x9c
Call Trace:
__param_initcall_debug+0x0/0x28 (unreliable)
drmem_init+0x144/0x2f8
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x298/0x38c
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0xb4
The ibm,dynamic-reconfiguration-memory device tree property generated
that causes this:
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Tested-by: Daniel Black <daniel@linux.vnet.ibm.com>
[mpe: Trim oops report] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Kelley [Wed, 14 Feb 2018 02:54:03 +0000 (02:54 +0000)]
cpumask: Make for_each_cpu_wrap() available on UP as well
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Michael Kelley <mhkelley@outlook.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kys@microsoft.com Cc: martin.petersen@oracle.com Cc: mikelley@microsoft.com Fixes: c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()") Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
The X86_P6_NOP config class leaves out many i686-class CPUs. Instead,
explicitly enumerate all these CPUs.
Using a configuration with M686 currently sets X86_MINIMUM_CPU_FAMILY=5
instead of the correct value of 6.
Booting on an i586 it will fail to generate the "This kernel
requires an i686 CPU, but only detected an i586 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i686-specific instructions.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1518713696-11360-3-git-send-email-tedheadster@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Several i586-class CPUs supporting this instruction are missing from
the X86_CMPXCHG64 config group.
Using a configuration with either M586TSC or M586MMX currently sets
X86_MINIMUM_CPU_FAMILY=4 instead of the correct value of 5.
Booting on an i486 it will fail to generate the "This kernel
requires an i586 CPU, but only detected an i486 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i586-specific instructions.
The M586 CPU is not in this list because at least the Cyrix 5x86
lacks this instruction, and perhaps others.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1518713696-11360-1-git-send-email-tedheadster@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:24 +0000 (00:51 +0100)]
kprobes: Propagate error from disarm_kprobe_ftrace()
Improve error handling when disarming ftrace-based kprobes. Like with
arm_kprobe_ftrace(), propagate any errors from disarm_kprobe_ftrace() so
that we do not disable/unregister kprobes that are still armed. In other
words, unregister_kprobe() and disable_kprobe() should not report success
if the kprobe could not be disarmed.
disarm_all_kprobes() keeps its current behavior and attempts to
disarm all kprobes. It returns the last encountered error and gives a
warning if not all probes could be disarmed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Jiri Kosina <jikos@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Link: http://lkml.kernel.org/r/20180109235124.30886-3-jeyu@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:23 +0000 (00:51 +0100)]
kprobes: Propagate error from arm_kprobe_ftrace()
Improve error handling when arming ftrace-based kprobes. Specifically, if
we fail to arm a ftrace-based kprobe, register_kprobe()/enable_kprobe()
should report an error instead of success. Previously, this has lead to
confusing situations where register_kprobe() would return 0 indicating
success, but the kprobe would not be functional if ftrace registration
during the kprobe arming process had failed. We should therefore take any
errors returned by ftrace into account and propagate this error so that we
do not register/enable kprobes that cannot be armed. This can happen if,
for example, register_ftrace_function() finds an IPMODIFY conflict (since
kprobe_ftrace_ops has this flag set) and returns an error. Such a conflict
is possible since livepatches also set the IPMODIFY flag for their ftrace_ops.
arm_all_kprobes() keeps its current behavior and attempts to arm all
kprobes. It returns the last encountered error and gives a warning if
not all probes could be armed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Jiri Kosina <jikos@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Link: http://lkml.kernel.org/r/20180109235124.30886-2-jeyu@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 16 Feb 2018 08:10:09 +0000 (09:10 +0100)]
Merge tag 'perf-core-for-mingo-4.17-20180215' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/core fixes from Arnaldo Carvalho de Melo:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf top'
using it, making it bearable to use it in large core count systems
such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the syscall
table id -> string tables used by 'perf trace' (Hendrik Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William Cohen)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Daniel Borkmann [Fri, 16 Feb 2018 00:10:29 +0000 (01:10 +0100)]
bpf: fix mlock precharge on arraymaps
syzkaller recently triggered OOM during percpu map allocation;
while there is work in progress by Dennis Zhou to add __GFP_NORETRY
semantics for percpu allocator under pressure, there seems also a
missing bpf_map_precharge_memlock() check in array map allocation.
Given today the actual bpf_map_charge_memlock() happens after the
find_and_alloc_map() in syscall path, the bpf_map_precharge_memlock()
is there to bail out early before we go and do the map setup work
when we find that we hit the limits anyway. Therefore add this for
array map as well.
Thierry Reding [Wed, 7 Feb 2018 17:40:27 +0000 (18:40 +0100)]
drm/nouveau: Make clock gate support conditional
The recently introduced clock gate support breaks on Tegra chips because
no thermal support is enabled for those devices. Conditionalize the code
on the existence of thermal support to fix this.
Fixes: b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1") Cc: Martin Peres <martin.peres@free.fr> Cc: Lyude Paul <lyude@redhat.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Fri, 16 Feb 2018 02:33:03 +0000 (12:33 +1000)]
Merge tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
There are important fixes for VLV with MIPI/DSI panels,
2 clean-up patches needed for this MIPI/DSI fix,
and many fixes for GEM including fixes for Perf OA and PMU,
and fixes on scheduler and preemption.
This also includes GVT fixes: "This has one to fix GTT mmio 8b
access from guest and two simple ones for mmio switch and typo fix"
* tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
Linus Torvalds [Thu, 15 Feb 2018 22:50:32 +0000 (14:50 -0800)]
Merge tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a system resume regression from the 4.13 cycle, clean up
device table handling in the ACPI core, update sysfs ABI documentation
of a couple of drivers and add an expected switch fall-through marker
to the SPCR table parsing code.
Specifics:
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva)"
* tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: dock: document sysfs interface
ACPI / DPTF: Document dptf_power sysfs atttributes
device property: Constify device_get_match_data()
ACPI / bus: Rename acpi_get_match_data() to acpi_device_get_match_data()
ACPI / bus: Remove checks in acpi_get_match_data()
ACPI / bus: Do not traverse through non-existed device table
ACPI: SPCR: Mark expected switch fall-through in acpi_parse_spcr
ACPI / EC: Restore polling during noirq suspend/resume phases
Linus Torvalds [Thu, 15 Feb 2018 22:40:01 +0000 (14:40 -0800)]
Merge tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently introduced build issue related to cpuidle and two
bugs in the PM core, update cpuidle documentation and clean up memory
allocations in the operating performance points (OPP) framework.
Specifics:
- Fix a recently introduced build issue related to cpuidle by
covering all of the relevant combinations of Kconfig options
in its header (Rafael Wysocki).
- Add missing invocation of pm_runtime_drop_link() to the
!CONFIG_SRCU variant of __device_link_del() (Lukas Wunner).
- Fix unbalanced IRQ enable in the wakeup interrupts framework
(Tony Lindgren).
- Update cpuidle sysfs ABI documentation (Aishwarya Pant).
- Use GFP_KERNEL instead of GFP_ATOMIC for allocating memory
in dev_pm_opp_init_cpufreq_table() (Jia-Ju Bai)"
* tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: cpuidle: Fix cpuidle_poll_state_init() prototype
PM / runtime: Update links_count also if !CONFIG_SRCU
PM / wakeirq: Fix unbalanced IRQ enable for wakeirq
Documentation/ABI: update cpuidle sysfs documentation
opp: cpu: Replace GFP_ATOMIC with GFP_KERNEL in dev_pm_opp_init_cpufreq_table
Linus Torvalds [Thu, 15 Feb 2018 22:31:28 +0000 (14:31 -0800)]
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Linus Torvalds [Thu, 15 Feb 2018 22:29:27 +0000 (14:29 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a bugfix for virtio 9p fs. It also fixes hybernation for
s390 guests with virtio devices"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: implement PM operations for virtio_ccw
9p/trans_virtio: discard zero-length reply
projects / mirror_ubuntu-kernels.git / log