usb: chipidea: Refactor USB PHY selection and keep a single PHY
Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.
This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.
All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: Grab the (legacy) USB PHY by phandle first
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX USB controller may drive the usb power line directly, but the
polarity depends on the board. Reset state of the polarity is low-active so
add this property to allow it to be high-active.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Torokhov [Sun, 17 Feb 2019 07:21:51 +0000 (23:21 -0800)]
usb: core: add option of only authorizing internal devices
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Nikolaus Voss [Wed, 20 Feb 2019 15:11:38 +0000 (16:11 +0100)]
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
Commit 1a2f474d328f handles block _reads_ separately with plain-I2C
adapters, but the problem described with regmap-i2c not handling
SMBus block transfers (i.e. read and writes) correctly also exists
with writes.
As workaround, this patch adds a block write function the same way 1a2f474d328f adds a block read function.
Fixes: 1a2f474d328f ("usb: typec: tps6598x: handle block reads separately with plain-I2C adapters") Fixes: 0a4c005bd171 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers") Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de> Cc: stable <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thierry Reding [Wed, 20 Feb 2019 13:48:41 +0000 (14:48 +0100)]
xhci: tegra: Prevent error pointer dereference
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Mans Rullgard [Tue, 19 Feb 2019 14:52:26 +0000 (14:52 +0000)]
usb: core: skip interfaces disabled in devicetree
If an interface has an associated devicetree node with status disabled,
do not register the device. This is useful for boards with a built-in
multifunction USB device where some functions are broken or otherwise
undesired.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Tue, 19 Feb 2019 13:43:33 +0000 (13:43 +0000)]
usb: typec: mux: remove redundant check on variable match
All the code paths that lead to the return statement are where
match is always true, hence the check to see if it is true is
redundant and can be removed.
Detected by CoverityScan, CID#14769672 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Karoly Pados [Sun, 17 Feb 2019 17:59:01 +0000 (18:59 +0100)]
USB: serial: cp210x: fix GPIO in autosuspend
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu> Fixes: cf5276ce7867 ("USB: serial: cp210x: Adding GPIO support for CP2105") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
YueHaibing [Fri, 15 Feb 2019 12:35:13 +0000 (12:35 +0000)]
usb: host: oxu210hp-hcd: remove set but not used variables 'uframes, transfer_buffer_length'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
variable 'uframes' set but not used [-Wunused-but-set-variable]
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
YueHaibing [Tue, 19 Feb 2019 06:57:50 +0000 (14:57 +0800)]
usb: typec: mux: Fix unsigned comparison with less than zero
The return from the call to fwnode_property_read_u16_array is int,
it can be a negative error code however this is being assigned to
an size_t variable 'nval', hence the check is always false.
Fix this by making 'nval' an int.
Detected by Coccinelle ("Unsigned expression compared with
zero: nval < 0")
Fixes: 96a6d031ca99 ("usb: typec: mux: Find the muxes by also matching against the device node") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
Heikki Krogerus [Wed, 13 Feb 2019 07:45:52 +0000 (10:45 +0300)]
device connection: Add fwnode member to struct device_connection
This will prepare the device connection API for connections
described in firmware.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:53 +0000 (10:45 +0300)]
usb: typec: mux: Find the muxes by also matching against the device node
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:57 +0000 (10:45 +0300)]
device connection: Find device connections also from device graphs
If connections between devices are described in OF graph or
ACPI device graph, we can find them by using the
fwnode_graph_*() functions.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Tested-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:55 +0000 (10:45 +0300)]
usb: typec: Find the ports by also matching against the device node
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:54 +0000 (10:45 +0300)]
usb: roles: Find the muxes by also matching against the device node
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Tested-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:56 +0000 (10:45 +0300)]
device connection: Prepare support for firmware described connections
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device. The endpoint member for the device names will not be
used at all in that case.
Acked-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Tested-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:51 +0000 (10:45 +0300)]
platform/x86: intel_cht_int33fe: Remove old style mux connections
The new mux connection naming scheme is now in use, so
dropping the connections still using the old names. From now
on the same connection description named "mode-switch" is
used with both the port and the alternate modes, so on CHT
the DP alt mode will use the same connection as the port to
get a handle to the mux device.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:50 +0000 (10:45 +0300)]
usb: typec: Rationalize the API for the muxes
Since with accessory modes there is no need for additional
identification when requesting a handle to the mux, we can
replace the second parameter that is passed to the
typec_mux_get() function with a pointer to alternate mode
description structure, and simply passing NULL with
accessory modes.
This change means the naming of the mux device connections
can be updated. Alternate and Accessory Modes will both be
handled with muxes named "mode-switch", and the orientation
switches will be named "orientation-switch".
Future identification of the alternate modes will be later
done using device property "svid" of the mux.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 07:45:49 +0000 (10:45 +0300)]
platform/x86: intel_cht_int33fe: Prepare for better mux naming scheme
Adding new connections with for the muxes with new
identifiers. The old connection are left in for now.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 13 Feb 2019 16:36:55 +0000 (19:36 +0300)]
usb: typec: tps6598x: Check mode of operation
To prevent loading of the driver when the PD controller is
still in some operational mode that the driver does not
support, checking the mode in driver probe callback
function.
TI PD controllers may be in undefined mode of operation
for example when the application code (firmware) is
completely missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Tue, 12 Feb 2019 15:58:17 +0000 (07:58 -0800)]
usb: typec: tcpm: Remove unused functions
tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the first place. Effectively that means that we don't know if they even
work, or ever did. Lets remove them.
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/usb/musb/musb_host.c: In function ‘musb_advance_schedule’:
drivers/usb/musb/musb_host.c:374:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (qh->mux == 1) {
^
drivers/usb/musb/musb_host.c:383:3: note: here
case USB_ENDPOINT_XFER_ISOC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: phy: twl6030-usb: fix possible use-after-free on remove
In remove(), use cancel_delayed_work_sync() to cancel the
delayed work. Otherwise there's a chance that this work
will continue to run until after the device has been removed.
This issue was detected with the help of Coccinelle.
Cc: Tony Lindgren <tony@atomide.com> Cc: Bin Liu <b-liu@ti.com> Fixes: b6a619a883c3 ("usb: phy: Check initial state for twl6030") Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Peter Chen [Tue, 12 Feb 2019 08:57:27 +0000 (08:57 +0000)]
usb: misc: usbtest: add super-speed isoc support
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Thinh Nguyen [Wed, 13 Feb 2019 03:39:27 +0000 (19:39 -0800)]
usb: dwc3: Reset num_trbs after skipping
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd5901414 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Merge tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.1
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits)
phy: qcom-qmp: Add QMP UFS PHY support for msm8998
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy
phy: bcm-sr-pcie: Change operation when PIPEMUX=1
phy: Add Cadence D-PHY support
dt-bindings: phy: Move the Cadence D-PHY bindings
phy: dphy: Clarify lanes parameter documentation
phy: dphy: Change units of wakeup and init parameters
phy: dphy: Remove unused header
MAINTAINERS: phy: fill Armada 3700 PHY drivers entry
dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings
phy: add A3700 UTMI PHY driver
MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver
dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings
phy: add A3700 COMPHY support
phy: mvebu-cp110-comphy: fix port check in ->xlate()
phy: armada375-usb2: switch to SPDX license identifier
phy: make phy-armada375-usb2 explicitly non-modular
phy: make phy-mvebu-sata explicitly non-modular
phy: make phy-core explicitly non-modular
phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
...
Paul Cercueil [Mon, 11 Feb 2019 17:14:50 +0000 (11:14 -0600)]
usb: musb: Kconfig: Drop dependency on CONFIG_USB for jz4740
The Kconfig entry previously depended on USB_OTG_BLACKLIST_HUB
unconditionally, which is an option that is only available when
CONFIG_USB is enabled. However, the USB IP in the JZ4740 SoC does not
support host mode, only gadget mode, so it makes sense to allow it to
build when CONFIG_USB is not set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Cercueil [Mon, 11 Feb 2019 17:14:49 +0000 (11:14 -0600)]
usb: musb: Kconfig: Drop dependency on MACH_JZ4740 for jz4740
Depending on MACH_JZ4740 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Cercueil [Mon, 11 Feb 2019 17:14:48 +0000 (11:14 -0600)]
usb: musb: jz4740: Add support for devicetree
Add support for probing the driver from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Cercueil [Mon, 11 Feb 2019 17:14:47 +0000 (11:14 -0600)]
Documentation: dt: Add binding info for jz4740-musb driver
This commit adds documentation for the device-tree bindings of the
jz4740-musb driver, which provides support for the USB gadget mode
of the JZ4740 and similar SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Mon, 11 Feb 2019 17:14:46 +0000 (11:14 -0600)]
USB: musb: fix indentation issue on a return statement
A return statement is indented one level too far, fix this by removing
a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Gonzalez [Fri, 8 Feb 2019 22:14:30 +0000 (23:14 +0100)]
phy: qcom-qmp: Add QMP UFS PHY support for msm8998
Use same init sequence as sdm845.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org> Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
fotg210-udc: pass struct device to DMA API functions
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065
Where the completion done is setup on the stack:
DECLARE_COMPLETION_ONSTACK(done);
Then later we setup a request and queue it, and wait for it:
if (unlikely(wait_for_completion_interruptible(&done))) {
/*
* To avoid race condition with ffs_epfile_io_complete,
* dequeue the request first then check
* status. usb_ep_dequeue API should guarantee no race
* condition with req->complete callback.
*/
usb_ep_dequeue(ep->ep, req);
interrupted = ep->status < 0;
}
The problem is, that we end up being interrupted, dequeue the
request, and exit.
But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.
Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:
wait_for_completion(&done);
Is needed right after the usb_ep_dequeue().
Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.
This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bdef4e ("usb: dwc3: gadget:
remove wait_end_transfer").
Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@kernel.org> Cc: Zeng Tao <prime.zeng@hisilicon.com> Cc: Jack Pham <jackp@codeaurora.org> Cc: Thinh Nguyen <thinh.nguyen@synopsys.com> Cc: Chen Yu <chenyu56@huawei.com> Cc: Jerry Zhang <zhangjerry@google.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Vincent Pelletier <plr.vincent@gmail.com> Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linux USB List <linux-usb@vger.kernel.org> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Linus Torvalds [Sun, 10 Feb 2019 18:39:37 +0000 (10:39 -0800)]
Merge tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dmatest: Abort test in case of mapping error
dmaengine: bcm2835: Fix abort of transactions
dmaengine: bcm2835: Fix interrupt race on RT
dmaengine: imx-dma: fix wrong callback invoke
dmaengine: at_xdmac: Fix wrongfull report of a channel as in use
Linus Torvalds [Sun, 10 Feb 2019 17:57:42 +0000 (09:57 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A handful of fixes:
- Fix an MCE corner case bug/crash found via MCE injection testing
- Fix 5-level paging boot crash
- Fix MCE recovery cache invalidation bug
- Fix regression on Xen guests caused by a recent PMD level mremap
speedup optimization"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Make set_pmd_at() paravirt aware
x86/mm/cpa: Fix set_mce_nospec()
x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()
Linus Torvalds [Sun, 10 Feb 2019 17:54:19 +0000 (09:54 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"irqchip driver fixes: most of them are race fixes for ARM GIC (General
Interrupt Controller) variants, but also a fix for the ARM MMP
(Marvell PXA168 et al) irqchip affecting OLPC keyboards"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix ITT_entry_size accessor
irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
irqchip/gic-v4: Fix occasional VLPI drop
Linus Torvalds [Sun, 10 Feb 2019 17:48:18 +0000 (09:48 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of kernel side fixes:
- Fix the Intel uncore driver on certain hardware configurations
- Fix a CPU hotplug related memory allocation bug
- Remove a spurious WARN()
... plus also a handful of perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script python: Add Python3 support to tests/attr.py
perf trace: Support multiple "vfs_getname" probes
perf symbols: Filter out hidden symbols from labels
perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
tools headers uapi: Sync linux/in.h copy from the kernel sources
perf clang: Do not use 'return std::move(something)'
perf mem/c2c: Fix perf_mem_events to support powerpc
perf tests evsel-tp-sched: Fix bitwise operator
perf/core: Don't WARN() for impossible ring-buffer sizes
perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
perf/x86/intel/uncore: Add Node ID mask
Juergen Gross [Sun, 10 Feb 2019 07:40:56 +0000 (08:40 +0100)]
x86/mm: Make set_pmd_at() paravirt aware
set_pmd_at() calls native_set_pmd() unconditionally on x86. This was
fine as long as only huge page entries were written via set_pmd_at(),
as Xen pv guests don't support those.
Commit 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions")
introduced a usage of set_pmd_at() possible on pv guests, leading to
failures like:
BUG: unable to handle kernel paging request at ffff888023e26778
#PF error: [PROT] [WRITE]
RIP: e030:move_page_tables+0x7c1/0xae0
move_vma.isra.3+0xd1/0x2d0
__se_sys_mremap+0x3c6/0x5b0
do_syscall_64+0x49/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Make set_pmd_at() paravirt aware by just letting it use set_pmd().
Fixes: 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions") Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: xen-devel@lists.xenproject.org Cc: boris.ostrovsky@oracle.com Cc: sstabellini@kernel.org Cc: hpa@zytor.com Cc: bp@alien8.de Cc: torvalds@linux-foundation.org Link: https://lkml.kernel.org/r/20190210074056.11842-1-jgross@suse.com
Linus Torvalds [Sat, 9 Feb 2019 21:43:12 +0000 (13:43 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One PM related driver bugfix and a MAINTAINERS update"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
i2c: omap: Use noirq system sleep pm ops to idle device for suspend
Linus Torvalds [Sat, 9 Feb 2019 20:41:14 +0000 (12:41 -0800)]
Merge tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A batch of MIPS fixes for 5.0, nothing too scary.
- A workaround for a Loongson 3 CPU bug is the biggest change, but
still fairly straightforward. It adds extra memory barriers (sync
instructions) around atomics to avoid a CPU bug that can break
atomicity.
- Loongson64 also sees a fix for powering off some systems which
would incorrectly reboot rather than waiting for the power down
sequence to complete.
- We have DT fixes for the Ingenic JZ4740 SoC & the JZ4780-based Ci20
board, and a DT warning fix for the Nexsys4/MIPSfpga board.
- The Cavium Octeon platform sees a further fix to the behaviour of
the pcie_disable command line argument that was introduced in v3.3.
- The VDSO, introduced in v4.4, sees build fixes for configurations
of GCC that were built using the --with-fp-32= flag to specify a
default 32-bit floating point ABI.
- get_frame_info() sees a fix for configurations with
CONFIG_KALLSYMS=n, for which it previously always returned an
error.
- If the MIPS Coherence Manager (CM) reports an error then we'll now
clear that error correctly so that the GCR_ERROR_CAUSE register
will be updated with information about any future errors"
* tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
MIPS: Remove function size check in get_frame_info()
MIPS: Use lower case for addresses in nexys4ddr.dts
MIPS: Loongson: Introduce and use loongson_llsc_mb()
MIPS: VDSO: Include $(ccflags-vdso) in o32,n32 .lds builds
MIPS: VDSO: Use same -m%-float cflag as the kernel proper
MIPS: OCTEON: don't set octeon_dma_bar_type if PCI is disabled
DTS: CI20: Fix bugs in ci20's device tree.
MIPS: DTS: jz4740: Correct interrupt number of DMA core
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
Linus Torvalds [Sat, 9 Feb 2019 18:17:01 +0000 (10:17 -0800)]
Merge tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- Fix a problem with the imx28 ECC engine
- Remove a debug trace introduced in 2b6f0090a333 ("mtd: Check
add_mtd_device() ret code")
- Make sure partitions of size 0 can be registered
- Fix kernel-doc warning in the rawnand core
- Fix the error path of spinand_init() (missing manufacturer cleanup in
a few places)
- Address a problem with the SPI NAND PROGRAM LOAD operation which does
not work as expected on some parts.
* tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd:
mtd: rawnand: gpmi: fix MX28 bus master lockup problem
mtd: Make sure mtd->erasesize is valid even if the partition is of size 0
mtd: Remove a debug trace in mtdpart.c
mtd: rawnand: fix kernel-doc warnings
mtd: spinand: Fix the error/cleanup path in spinand_init()
mtd: spinand: Handle the case where PROGRAM LOAD does not reset the cache
Linus Torvalds [Sat, 9 Feb 2019 17:44:08 +0000 (09:44 -0800)]
Merge tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two very minor fixes: one remove of a #include for an unused header
and a fix of the xen ML address in MAINTAINERS"
* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: unify reference to xen-devel list
arch/arm/xen: Remove duplicate header
Ingo Molnar [Sat, 9 Feb 2019 12:13:45 +0000 (13:13 +0100)]
Merge tag 'perf-urgent-for-mingo-5.0-20190205' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf trace:
Arnaldo Carvalho de Melo:
Fix handling of probe:vfs_getname when the probed routine is
inlined in multiple places, fixing the collection of the 'filename'
parameter in open syscalls.
perf test:
Gustavo A. R. Silva:
Fix bitwise operator usage in evsel-tp-sched test, which made tat
test always detect fields as signed.
Jiri Olsa:
Filter out hidden symbols from labels, added in systems where the
annobin plugin is used, such as RHEL8, which, if left in place make
the DWARF unwind 'perf test' to fail on PPC.
Tony Jones:
Fix 'perf_event_attr' tests when building with python3.
perf mem/c2c:
Ravi Bangoria:
Fix perf_mem_events on PowerPC.
tools headers UAPI:
Arnaldo Carvalho de Melo:
Sync linux/in.h copy from the kernel sources, silencing a perf build warning.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 9 Feb 2019 00:23:41 +0000 (16:23 -0800)]
Merge tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a bit larger than normal, as we had not managed to send out a
pull request before traveling for a week without my signing key.
There are multiple code fixes for older bugs, all of which should get
backported into stable kernels:
- tango: one fix for multiplatform configurations broken on other
platforms when tango is enabled
- arm_scmi: device unregistration fix
- iop32x: fix kernel oops from extraneous __init annotation
- pxa: remove a double kfree
- fsl qbman: close an interrupt clearing race
The rest is the usual collection of smaller fixes for device tree
files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
imx platforms.
Some of these are for compile-time warnings, most are for board
specific functionality that fails to work because of incorrect
settings"
* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
firmware: arm_scmi: provide the mandatory device release callback
ARM: iop32x/n2100: fix PCI IRQ mapping
arm64: dts: add msm8996 compatible to gicv3
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: pxa: ssp: unneeded to free devm_ allocated data
ARM: dts: r8a7743: Convert to new LVDS DT bindings
soc: fsl: qbman: avoid race in clearing QMan interrupt
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
ARM: dts: da850: fix interrupt numbers for clocksource
dt-bindings: imx8mq: Number clocks consecutively
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
...
Linus Torvalds [Sat, 9 Feb 2019 00:21:33 +0000 (16:21 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two arm64 fixes for -rc6. They resolve a kernel NULL dereference in
kexec and bogus kernel page table dumping when userspace is configured
for 52-bit virtual addressing.
Summary:
- Fix kernel oops when attemping kexec_file() with a NULL cmdline
- Fix page table output in debugfs when ARM64_USER_VA_BITS_52=y"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: handle empty command-line
arm64: ptdump: Don't iterate kernel page tables using PTRS_PER_PXX
Linus Torvalds [Sat, 9 Feb 2019 00:04:12 +0000 (16:04 -0800)]
Merge tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Just two fixes, both going to stable.
- Our support for split pmd page table lock had a bug which could
lead to a crash on mremap() when using the Radix MMU (Power9 only).
- A fix for the PAPR SCM driver (nvdimm) we added last release, which
had a bug where we might mis-handle a hypervisor response leading
to us failing to attach the memory region.
Thanks to: Aneesh Kumar K.V, Oliver O'Halloran"
* tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Use the correct bind address
powerpc/radix: Fix kernel crash with mremap()
Linus Torvalds [Fri, 8 Feb 2019 23:39:28 +0000 (15:39 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal fixes from Eric Biederman:
"This contains four small fixes for signal handling. A missing range
check, a regression fix, prioritizing signals we have already started
a signal group exit for, and better detection of synchronous signals.
The confused decision of which signals to handle failed spectacularly
when a timer was pointed at SIGBUS and the stack overflowed. Resulting
in an unkillable process in an infinite loop instead of a SIGSEGV and
core dump"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Better detection of synchronous signals
signal: Always notice exiting tasks
signal: Always attempt to allocate siginfo for SIGSTOP
signal: Make siginmask safe when passed a signal of 0
Linus Torvalds [Fri, 8 Feb 2019 23:37:17 +0000 (15:37 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five minor fixes (although, tecnhincally, the aicxxx
fix is for a major problem in that the driver won't load without it,
but I think the fact it's taken us since 4.10 to discover this
indicates that the user base for these things has declined)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: Prevent deadlock when adapter probe fails
Revert "scsi: libfc: Add WARN_ON() when deleting rports"
scsi: sd_zbc: Fix zone information messages
scsi: target: make the pi_prot_format ConfigFS path readable
scsi: aic94xx: fix module loading
Linus Torvalds [Fri, 8 Feb 2019 23:34:10 +0000 (15:34 -0800)]
Merge tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Intel decided to leave the newly added Scalable Mode Feature
default-disabled for now. The patch here accomplishes that"
* tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Leave scalable mode default off
Linus Torvalds [Fri, 8 Feb 2019 23:32:10 +0000 (15:32 -0800)]
Merge tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX) that
breaks PCIe on I.MX SoCs (Thinh Nguyen)"
* tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX)
Linus Torvalds [Fri, 8 Feb 2019 23:30:02 +0000 (15:30 -0800)]
Merge tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This prevents excessive ACPI debug messages from being printed to the
kernel log, which has started to happen after one of the recent ACPICA
commits (Erik Schmauss)"
* tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Set debug output flags independent of ACPICA
Pull networking fixes from David Miller:
"This pull request is dedicated to the upcoming snowpocalypse parts 2
and 3 in the Pacific Northwest:
1) Drop profiles are broken because some drivers use dev_kfree_skb*
instead of dev_consume_skb*, from Yang Wei.
2) Fix IWLWIFI kconfig deps, from Luca Coelho.
3) Fix percpu maps updating in bpftool, from Paolo Abeni.
4) Missing station release in batman-adv, from Felix Fietkau.
5) Fix some networking compat ioctl bugs, from Johannes Berg.
6) ucc_geth must reset the BQL queue state when stopping the device,
from Mathias Thore.
7) Several XDP bug fixes in virtio_net from Toshiaki Makita.
8) TSO packets must be sent always on queue 0 in stmmac, from Jose
Abreu.
9) Fix socket refcounting bug in RDS, from Eric Dumazet.
10) Handle sparse cpu allocations in bpf selftests, from Martynas
Pumputis.
11) Make sure mgmt frames have enough tailroom in mac80211, from Felix
Feitkau.
12) Use safe list walking in sctp_sendmsg() asoc list traversal, from
Greg Kroah-Hartman.
13) Make DCCP's ccid_hc_[rt]x_parse_options always check for NULL
ccid, from Eric Dumazet.
14) Need to reload WoL password into bcmsysport device after deep
sleeps, from Florian Fainelli.
15) Remove filter from mask before freeing in cls_flower, from Petr
Machata.
16) Missing release and use after free in error paths of s390 qeth
code, from Julian Wiedmann.
17) Fix lockdep false positive in dsa code, from Marc Zyngier.
18) Fix counting of ATU violations in mv88e6xxx, from Andrew Lunn.
19) Fix EQ firmware assert in qed driver, from Manish Chopra.
20) Don't default Caivum PTP to Y in kconfig, from Bjorn Helgaas"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: dsa: b53: Fix for failure when irq is not defined in dt
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
net: Don't default Cavium PTP driver to 'y'
net: broadcom: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: via-velocity: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tehuti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: sun: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fsl_ucc_hdlc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fec_mpc52xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: smsc: epic100: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: dscc4: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tulip: de2104x: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: defxx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net/mlx5e: Don't overwrite pedit action when multiple pedit used
net/mlx5e: Update hw flows when encap source mac changed
qed*: Advance drivers version to 8.37.0.20
qed: Change verbosity for coalescing message.
qede: Fix system crash on configuring channels.
qed: Consider TX tcs while deriving the max num_queues for PF.
...
Linus Torvalds [Fri, 8 Feb 2019 18:56:31 +0000 (10:56 -0800)]
Merge tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.0-rc6.
Nothing huge here, some more binderfs fixups found as people use it,
and there is a "large" selftest added to validate the binderfs code,
which makes up the majority of this pull request.
There's also some small mei and mic fixes to resolve some reported
issues.
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mic: vop: Fix crash on remove
mic: vop: Fix use-after-free on remove
binderfs: remove separate device_initcall()
fpga: stratix10-soc: fix wrong of_node_put() in init function
mic: vop: Fix broken virtqueues
mei: free read cb on ctrl_wr list flush
samples: mei: use /dev/mei0 instead of /dev/mei
mei: me: add ice lake point device id.
binderfs: respect limit on binder control creation
binder: fix CONFIG_ANDROID_BINDER_DEVICES
selftests: add binderfs selftests
Linus Torvalds [Fri, 8 Feb 2019 18:53:44 +0000 (10:53 -0800)]
Merge tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 5.0-rc6.
Well, not so much "driver core" as "debugfs". There's a lot of
outstanding debugfs cleanup patches coming in through different
subsystem trees, and in that process the debugfs core was found that
it really should return errors when something bad happens, to prevent
random files from showing up in the root of debugfs afterward. So
debugfs was fixed up to handle this properly, and then two fixes for
the relay and blk-mq code was needed as it was making invalid
assumptions about debugfs return values.
There's also a cacheinfo fix in here that resolves a tiny issue.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
blk-mq: protect debugfs_create_files() from failures
relay: check return of create_buf_file() properly
debugfs: debugfs_lookup() should return NULL if not found
debugfs: return error values, not NULL
debugfs: fix debugfs_rename parameter checking
cacheinfo: Keep the old value if of_property_read_u32 fails
Linus Torvalds [Fri, 8 Feb 2019 18:49:55 +0000 (10:49 -0800)]
Merge tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: fix race between flush_to_ldisc and tty_open
staging: speakup: fix tty-operation NULL derefs
serial: sh-sci: Do not free irqs that have already been freed
serial: 8250_pci: Make PCI class test non fatal
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
Linus Torvalds [Fri, 8 Feb 2019 18:46:14 +0000 (10:46 -0800)]
Merge tag 'xfs-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are a handful of XFS fixes to fix a data corruption problem, a
crasher bug, and a deadlock.
Summary:
- Fix cache coherency problem with writeback mappings
- Fix buffer deadlock when shutting fs down
- Fix a null pointer dereference when running online repair"
* tag 'xfs-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: set buffer ops when repair probes for btree type
xfs: end sync buffer I/O properly on shutdown error
xfs: eof trim writeback mapping as soon as it is cached
Linus Torvalds [Fri, 8 Feb 2019 18:43:15 +0000 (10:43 -0800)]
Merge tag 'drm-fixes-2019-02-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Missed fixes last week as had nothing until amdgpu showed up on
Saturday. Other stuff has since rolled in along with some more amdgpu
fixes, so we have two weeks of those, and some i915, vmwgfx, sun4i,
rockchip and omap fixes.
amdgpu/radeon:
- fix crash on passthrough for SI
- fencing fix for shared buffers
- APU hwmon fix
- API powerplay fix
- eDP freesync fix
- PASID mgr locking fix
- KFD warning fix
- DC/powerplay fix
- raven revision ids fix
- vega20 doorbell fix
* tag 'drm-fixes-2019-02-08' of git://anongit.freedesktop.org/drm/drm: (28 commits)
drm/omap: dsi: Hack-fix DSI bus flags
drm/omap: dsi: Fix OF platform depopulate
drm/omap: dsi: Fix crash in DSI debug dumps
drm/i915: Try to sanitize bogus DPLL state left over by broken SNB BIOSen
drm/amd/display: Attach VRR properties for eDP connectors
drm/amdkfd: Fix if preprocessor statement above kfd_fill_iolink_info_for_cpu
drm/amdgpu: use spin_lock_irqsave to protect vm_manager.pasid_idr
drm/i915: always return something on DDI clock selection
drm/i915: Fix skl srckey mask bits
drm/vmwgfx: Improve on IOMMU detection
drm/vmwgfx: Fix setting of dma masks
drm/vmwgfx: Also check for crtc status while checking for DU active
drm/vmwgfx: Fix an uninitialized fence handle value
drm/vmwgfx: Return error code from vmw_execbuf_copy_fence_user
drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init
drm/amdgpu: fix the incorrect external id for raven series
drm/amdgpu: Implement doorbell self-ring for NBIO 7.4
drm/amd/display: Fix fclk idle state
drm/amdgpu: Transfer fences to dmabuf importer
drm/amd/powerplay: Fix missing break in switch
...
Lukas Bulwahn [Sat, 12 Jan 2019 09:07:23 +0000 (10:07 +0100)]
MAINTAINERS: unify reference to xen-devel list
In the linux kernel MAINTAINERS file, largely
"xen-devel@lists.xenproject.org (moderated for non-subscribers)"
is used to refer to the xen-devel mailing list.
The DRM DRIVERS FOR XEN section entry mentions
xen-devel@lists.xen.org instead, but that is just the same
mailing list as the mailing list above.
Peter Zijlstra [Fri, 8 Feb 2019 12:08:59 +0000 (13:08 +0100)]
x86/mm/cpa: Fix set_mce_nospec()
The recent commit fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and
cpa_flush_array() into a single cpa_flush() function") accidentally made
the call to make_addr_canonical_again() go away, which breaks
set_mce_nospec().
Re-instate the call to convert the address back into canonical form right
before invoking either CLFLUSH or INVLPG. Rename the function while at it
to be shorter (and less MAGA).
Fixes: fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and cpa_flush_array() into a single cpa_flush() function") Reported-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tony Luck <tony.luck@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Rik van Riel <riel@surriel.com> Link: https://lkml.kernel.org/r/20190208120859.GH32511@hirez.programming.kicks-ass.net
Thomas Gleixner [Tue, 29 Jan 2019 22:15:12 +0000 (23:15 +0100)]
futex: Handle early deadlock return correctly
commit 56222b212e8e ("futex: Drop hb->lock before enqueueing on the
rtmutex") changed the locking rules in the futex code so that the hash
bucket lock is not longer held while the waiter is enqueued into the
rtmutex wait list. This made the lock and the unlock path symmetric, but
unfortunately the possible early exit from __rt_mutex_proxy_start() due to
a detected deadlock was not updated accordingly. That allows a concurrent
unlocker to observe inconsitent state which triggers the warning in the
unlock path.
The problem is caused by the remove(rtmutex_waiter) in the failure case of
__rt_mutex_proxy_start() as this lets the unlocker observe a waiter in the
hash bucket but no waiter on the rtmutex, i.e. inconsistent state.
The original commit handles this correctly for the other early return cases
(timeout, signal) by delaying the removal of the rtmutex waiter until the
returning task reacquired the hash bucket lock.
Treat the failure case of __rt_mutex_proxy_start() in the same way and let
the existing cleanup code handle the eventual handover of the rtmutex
gracefully. The regular rt_mutex_proxy_start() gains the rtmutex waiter
removal for the failure case, so that the other callsites are still
operating correctly.
Add proper comments to the code so all these details are fully documented.
Thanks to Peter for helping with the analysis and writing the really
valuable code comments.
Fixes: 56222b212e8e ("futex: Drop hb->lock before enqueueing on the rtmutex") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Co-developed-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: linux-s390@vger.kernel.org Cc: Stefan Liebler <stli@linux.ibm.com> Cc: Sebastian Sewior <bigeasy@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1901292311410.1950@nanos.tec.linutronix.de
Davidlohr Bueso [Wed, 6 Feb 2019 18:56:02 +0000 (10:56 -0800)]
futex: Fix barrier comment
The current comment for the barrier that guarantees that waiter increment
is always before taking the hb spinlock (barrier (A)) needs to be fixed as
it is misplaced.
This is obviously referring to hb_waiters_inc, which is a full barrier.
Heikki Krogerus [Fri, 1 Feb 2019 10:47:55 +0000 (13:47 +0300)]
usb: typec: Prepare alt mode enter/exit reporting for UCSI alt mode support
Because of UCSI, we have to support alt mode enter/exit
reporting even when there is no alt mode driver bind to the
alt mode device. With UCSI a firmware handles the alternate
modes, and the modes are entered automatically from OS PoW.
Changing typec_altmode_update_active() so that the driver
module ref count is incremented/decremented only if there
really is a driver for the alt mode. That avoids a NULL
pointer dereference from happening when the driver is
missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>