The bulk of ATA host state machine is implemented by
ata_sff_hsm_move(). The function is called from either the interrupt
handler or, if polling, a work item. Unlike from the interrupt path,
the polling path calls the function without holding the host lock and
ata_sff_hsm_move() selectively grabs the lock.
This is completely broken. If an IRQ triggers while polling is in
progress, the two can easily race and end up accessing the hardware
and updating state machine state at the same time. This can put the
state machine in an illegal state and lead to a crash like the
following.
Fix it by ensuring that the polling path is holding the host lock
before entering ata_sff_hsm_move() so that all hardware accesses and
state updates are performed under the host lock.
The non-DT platform that uses this driver (actually the AVR32) was taking a bad
branch for determining if the IP would use gpio for CS.
Adding the presence of DT as a condition fixes this issue.
Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller") Reported-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[nicolas.ferre@atmel.com: extract from ml discussion] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().
It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.
Also, it handles the case where the check happens before
transport_send_task_abort() gets called. For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.
Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.
It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.
Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.
Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.
Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@daterainc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes a bug in TMR task aborted status (TAS)
handling when multiple sessions are connected to the
same target WWPN endpoint and se_node_acl descriptor,
resulting in TASK_ABORTED status to not be generated
for aborted se_cmds on the remote port.
This is due to core_tmr_handle_tas_abort() incorrectly
comparing se_node_acl instead of se_session, for which
the multi-session case is expected to be sharing the
same se_node_acl.
Instead, go ahead and update core_tmr_handle_tas_abort()
to compare tmr_sess + cmd->se_sess in order to determine
if the LUN_RESET was received on a different I_T nexus,
and TASK_ABORTED status response needs to be generated.
Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active TMRs,
triggered during se_cmd + se_tmr_req descriptor
shutdown + release via core_tmr_drain_tmr_list().
To address this bug, go ahead and obtain a local
kref_get_unless_zero(&se_cmd->cmd_kref) for active I/O
to set CMD_T_ABORTED, and transport_wait_for_tasks()
followed by the final target_put_sess_cmd() to drop
the local ->cmd_kref.
Also add two new checks within target_tmr_work() to
avoid CMD_T_ABORTED -> TFO->queue_tm_rsp() callbacks
ahead of invoking the backend -> fabric put in
transport_cmd_check_stop_to_fabric().
For good measure, also change core_tmr_release_req()
to use list_del_init() ahead of se_tmr_req memory
free.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active se_cmd
I/O, that can be triggered during se_cmd descriptor
shutdown + release via core_tmr_drain_state_list() code.
To address this bug, add common __target_check_io_state()
helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE
checking, and set CMD_T_ABORTED + obtain ->cmd_kref for
both cases ahead of last target_put_sess_cmd() after
TFO->aborted_task() -> transport_cmd_finish_abort()
callback has completed.
It also introduces SCF_ACK_KREF to determine when
transport_cmd_finish_abort() needs to drop the second
extra reference, ahead of calling target_put_sess_cmd()
for the final kref_put(&se_cmd->cmd_kref).
It also updates transport_cmd_check_stop() to avoid
holding se_cmd->t_state_lock while dropping se_cmd
device state via target_remove_from_state_list(), now
that core_tmr_drain_state_list() is holding the
se_device lock while checking se_cmd state from
within TMR logic.
Finally, move transport_put_cmd() release of SGL +
TMR + extended CDB memory into target_free_cmd_mem()
in order to avoid potential resource leaks in TMR
ABORT_TASK + LUN_RESET code-paths. Also update
target_release_cmd_kref() accordingly.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
include/target/target_core_base.h
After login to the desktop on Dell Inspiron 3162,
there's a very loud background noise comes from the builtin speaker.
The noise does not go away even if the speaker is muted.
The noise disappears after using the aamix fixup.
Codec: Realtek ALC3234
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0255
Subsystem Id: 0x10280725
Revision Id: 0x100002
No Modem Function Group found
Some Skylake machines show the codec probe errors in certain
situations, e.g. HP Z240 desktop fails to probe the onboard Realtek
codec at reloading the snd-hda-intel module like:
snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x000000
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: lastcmd=0x000f0000
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x000f0000
snd_hda_intel 0000:00:1f.3: Codec #0 probe error; disabling it...
hdaudio hdaudioC0D2: no AFG or MFG node found
snd_hda_intel 0000:00:1f.3: no codecs initialized
Also, HP G470 G3 suffers from the similar problem, as reported in
bugzilla below. On this machine, the codec probe error appears even
at a fresh boot.
As Libin suggested, the same workaround used for Broxton in the commit
[6639484ddaf6: ALSA: hda - disable dynamic clock gating on Broxton
before reset] can be applied for Skylake in order to fix this problem.
The Intel HW team also confirmed that this is needed for SKL.
This patch makes the workaround applied to both SKL and BXT
platforms. The referred macros are moved and one superfluous macro
(IS_BROXTON()) is another one (IS_BXT()) as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112731 Suggested-by: Libin Yang <libin.yang@linux.intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Workqueue used to implicity guarantee that work items queued without
explicit CPU specified are put on the local CPU. Recent changes in
timer broke the guarantee and led to vmstat breakage which was fixed
by 176bed1de5bf ("vmstat: explicitly schedule per-cpu work on the CPU
we need it to run on").
vmstat is the most likely to expose the issue and it's quite possible
that there are other similar problems which are a lot more difficult
to trigger. As a preventive measure, 874bbfe600a6 ("workqueue: make
sure delayed work run in local cpu") was applied to restore the local
CPU guarnatee. Unfortunately, the change exposed a bug in timer code
which got fixed by 22b886dd1018 ("timers: Use proper base migration in
add_timer_on()"). Due to code restructuring, the commit couldn't be
backported beyond certain point and stable kernels which only had 874bbfe600a6 started crashing.
The local CPU guarantee was accidental more than anything else and we
want to get rid of it anyway. As, with the vmstat case fixed, 874bbfe600a6 is causing more problems than it's fixing, it has been
decided to take the chance and officially break the guarantee by
reverting the commit. A debug feature will be added to force foreign
CPU assignment to expose cases relying on the guarantee and fixes for
the individual cases will be backported to stable as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 874bbfe600a6 ("workqueue: make sure delayed work run in local cpu") Link: http://lkml.kernel.org/g/20160120211926.GJ10810@quack.suse.cz Cc: Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Daniel Bilik <daniel.bilik@neosystem.cz> Cc: Jan Kara <jack@suse.cz> Cc: Shaohua Li <shli@fb.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Daniel Bilik <daniel.bilik@neosystem.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When looking up the pool_workqueue to use for an unbound workqueue,
workqueue assumes that the target CPU is always bound to a valid NUMA
node. However, currently, when a CPU goes offline, the mapping is
destroyed and cpu_to_node() returns NUMA_NO_NODE.
This has always been broken but hasn't triggered often enough before 874bbfe600a6 ("workqueue: make sure delayed work run in local cpu").
After the commit, workqueue forcifully assigns the local CPU for
delayed work items without explicit target CPU to fix a different
issue. This widens the window where CPU can go offline while a
delayed work item is pending causing delayed work items dispatched
with target CPU set to an already offlined CPU. The resulting
NUMA_NO_NODE mapping makes workqueue try to queue the work item on a
NULL pool_workqueue and thus crash.
While 874bbfe600a6 has been reverted for a different reason making the
bug less visible again, it can still happen. Fix it by mapping
NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node().
This is a temporary workaround. The long term solution is keeping CPU
-> NODE mapping stable across CPU off/online cycles which is being
worked on.
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The code within wait_event_interruptible() is called with
!TASK_RUNNING, so mustn't call any functions that can sleep,
like mutex_lock().
Since we re-check the list_empty() in a loop after the wait,
it's safe to simply use list_empty() without locking.
This bug has existed forever, but was only discovered now
because all userspace implementations, including the default
'rfkill' tool, use poll() or select() to get a readable fd
before attempting to read.
commit 0ff53d096422 sets the next tick interrupt to the last jiffies update,
i.e. in the past, because the forward operation is invoked before the set
operation. There is no resulting damage (yet), but we get an extra pointless
tick interrupt.
Revert the order so we get the next tick interrupt in the future.
Fixes: commit 0ff53d096422 "tick: sched: Force tick interrupt and get rid of softirq magic" Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Link: http://lkml.kernel.org/r/1453893967-3458-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This commit merged interval and overall counters reading into single
read_counters function.
The old interval code cleaned the stddev data for some reason (it's
never displayed in interval mode) and the mentioned commit kept on
cleaning the stddev data in merged function, which resulted in the
stddev not being displayed.
Removing the wrong stddev data cleanup init_stats call.
Reported-and-Tested-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Fixes: 106a94a0f8c2 ("perf stat: Introduce read_counters function") Link: http://lkml.kernel.org/r/1453290995-18485-4-git-send-email-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit f79b0d9c223c ("staging: speakup: Fixed warning <linux/serial.h>
instead of <asm/serial.h>") broke the port information in the speakup
driver: SERIAL_PORT_DFNS only gets defined if asm/serial.h is included,
and no other header includes asm/serial.h.
We here make sure serialio.c does get the arch-specific definition of
SERIAL_PORT_DFNS from asm/serial.h, if any.
Along the way, this makes sure that we do have information for the
requested serial port number (index)
Fixes: f79b0d9c223c ("staging: speakup: Fixed warning <linux/serial.h> instead of <asm/serial.h>") Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit ca369d51b3e1 ("block/sd: Fix device-imposed transfer length
limits") accidentally switched optimal I/O size reporting from bytes to
block layer sectors.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Fixes: ca369d51b3e1649be4a72addd6d6a168cfb3f537 Reviewed-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit d15f9d694b77 ("libceph: check data_len in ->alloc_msg()")
mistakenly bumped the log level on the "tid %llu unknown, skipping"
message. Turn it back into a dout() - stray replies are perfectly
normal when OSDs flap, crash, get killed for testing purposes, etc.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The contract between try_read() and try_write() is that when called
each processes as much data as possible. When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more. try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.
Reported-by: Varada Kari <Varada.Kari@sandisk.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Varada Kari <Varada.Kari@sandisk.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
There are a number of problems with revoking a "was sending" message:
(1) We never make any attempt to revoke data - only kvecs contibute to
con->out_skip. However, once the header (envelope) is written to the
socket, our peer learns data_len and sets itself to expect at least
data_len bytes to follow front or front+middle. If ceph_msg_revoke()
is called while the messenger is sending message's data portion,
anything we send after that call is counted by the OSD towards the now
revoked message's data portion. The effects vary, the most common one
is the eventual hang - higher layers get stuck waiting for the reply to
the message that was sent out after ceph_msg_revoke() returned and
treated by the OSD as a bunch of data bytes. This is what Matt ran
into.
(2) Flat out zeroing con->out_kvec_bytes worth of bytes to handle kvecs
is wrong. If ceph_msg_revoke() is called before the tag is sent out or
while the messenger is sending the header, we will get a connection
reset, either due to a bad tag (0 is not a valid tag) or a bad header
CRC, which kind of defeats the purpose of revoke. Currently the kernel
client refuses to work with header CRCs disabled, but that will likely
change in the future, making this even worse.
(3) con->out_skip is not reset on connection reset, leading to one or
more spurious connection resets if we happen to get a real one between
con->out_skip is set in ceph_msg_revoke() and before it's cleared in
write_partial_skip().
Fixing (1) and (3) is trivial. The idea behind fixing (2) is to never
zero the tag or the header, i.e. send out tag+header regardless of when
ceph_msg_revoke() is called. That way the header is always correct, no
unnecessary resets are induced and revoke stands ready for disabled
CRCs. Since ceph_msg_revoke() rips out con->out_msg, introduce a new
"message out temp" and copy the header into it before sending.
Reported-by: Matt Conner <matt.conner@keepertech.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Matt Conner <matt.conner@keepertech.com> Reviewed-by: Sage Weil <sage@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Before this patch, a process with some permissive seccomp filter
that was applied by root without NO_NEW_PRIVS was able to add
more filters to itself without setting NO_NEW_PRIVS by setting
the new filter from a throwaway thread with NO_NEW_PRIVS.
There is a race discovered by Juri, where we are able to:
- create and read a sysfs file before policy->governor_data is being set
to a non NULL value.
OR
- set policy->governor_data to NULL, and reading a file before being
destroyed.
There are two definitions of pxa_cpufreq_change_voltage, with slightly
different prototypes after one of them had its argument marked 'const'.
Now the other one (for !CONFIG_REGULATOR) produces a harmless warning:
drivers/cpufreq/pxa2xx-cpufreq.c: In function 'pxa_set_target':
drivers/cpufreq/pxa2xx-cpufreq.c:291:36: warning: passing argument 1 of 'pxa_cpufreq_change_voltage' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]);
^
drivers/cpufreq/pxa2xx-cpufreq.c:205:12: note: expected 'struct pxa_freqs *' but argument is of type 'const struct pxa_freqs *'
static int pxa_cpufreq_change_voltage(struct pxa_freqs *pxa_freq)
^
This changes the prototype in the same way as the other, which
avoids the warning.
Fixes: 03c229906311 (cpufreq: pxa: make pxa_freqs arrays const) Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).
When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.
Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.
Since Linux 4.0 the CPU fan speed is going up and down on Dell Studio
XPS 8000 and 8100 for unknown reasons. The 8100 was already
blacklisted in commit a4b45b25f18d ("hwmon: (dell-smm) Blacklist
Dell Studio XPS 8100"). This patch blacklists the XPS 8000.
Without further debugging on the affected machine, it is not possible
to find the problem. For more details see
https://bugzilla.kernel.org/show_bug.cgi?id=100121
When a new cooling device is registered, we need to update the
thermal zone to set the new registered cooling device to a proper
state.
This fixes a problem that the system is cool, while the fan devices
are left running on full speed after boot, if fan device is registered
after thermal zone device.
Here is the history of why current patch looks like this:
https://patchwork.kernel.org/patch/7273041/
Current thermal code does not handle system sleep well because
1. the cooling device cooling state may be changed during suspend
2. the previous temperature reading becomes invalid after resumed because
it is got before system sleep
3. updating thermal zone device during suspending/resuming
is wrong because some devices may have already been suspended
or may have not been resumed.
Thus, the proper way to do this is to cancel all thermal zone
device update requirements during suspend/resume, and after all
the devices have been resumed, reset and update every registered
thermal zone devices.
This also fixes a regression introduced by:
Commit 19593a1fb1f6 ("ACPI / fan: convert to platform driver")
Because, with above commit applied, all the fan devices are attached
to the acpi_general_pm_domain, and they are turned on by the pm_domain
automatically after resume, without the awareness of thermal core.
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
The current code is problematic when the QP creation and ipoib is used to
support NFS and NFS desires to do IO for paging purposes. In that case, the
GFP_KERNEL allocation in qib_qp.c causes a deadlock in tight memory
situations.
This fix adds support to create queue pair with GFP_NOIO flag for connected
mode only to cleanly fail the create queue pair in those situations.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
ib_send_cm_drep() calls cm_enter_timewait() while holding a spinlock
that can be locked from inside an interrupt handler. Hence do not
enable interrupts inside cm_enter_timewait() if called with interrupts
disabled.
This patch fixes e.g. the following deadlock: Acked-by: Erez Shitrit <erezsh@mellanox.com>
=================================
[ INFO: inconsistent lock state ]
4.4.0-rc7+ #1 Tainted: G E
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
swapper/8/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&cm_id_priv->lock)->rlock){?.+...}, at: [<ffffffffa036eec4>] cm_establish+0x
74/0x1b0 [ib_cm]
{HARDIRQ-ON-W} state was registered at:
[<ffffffff810a3c11>] mark_held_locks+0x71/0x90
[<ffffffff810a3e87>] trace_hardirqs_on_caller+0xa7/0x1c0
[<ffffffff810a3fad>] trace_hardirqs_on+0xd/0x10
[<ffffffff8151c40b>] _raw_spin_unlock_irq+0x2b/0x40
[<ffffffffa036ea8e>] cm_enter_timewait+0xae/0x100 [ib_cm]
[<ffffffffa036ff76>] ib_send_cm_drep+0xb6/0x190 [ib_cm]
[<ffffffffa052ed08>] srp_cm_handler+0x128/0x1a0 [ib_srp]
[<ffffffffa0370340>] cm_process_work+0x20/0xf0 [ib_cm]
[<ffffffffa0371335>] cm_dreq_handler+0x135/0x2c0 [ib_cm]
[<ffffffffa03733c5>] cm_work_handler+0x75/0xd0 [ib_cm]
[<ffffffff8107184d>] process_one_work+0x1bd/0x460
[<ffffffff81073148>] worker_thread+0x118/0x420
[<ffffffff81078454>] kthread+0xe4/0x100
[<ffffffff8151cbbf>] ret_from_fork+0x3f/0x70
irq event stamp: 1672286
hardirqs last enabled at (1672283): [<ffffffff81408ec0>] poll_idle+0x10/0x80
hardirqs last disabled at (1672284): [<ffffffff8151d304>] common_interrupt+0x84/0x89
softirqs last enabled at (1672286): [<ffffffff8105b4dc>] _local_bh_enable+0x1c/0x50
softirqs last disabled at (1672285): [<ffffffff8105b697>] irq_enter+0x47/0x70
other info that might help us debug this:
Possible unsafe locking scenario:
Fixes: commit be4b499323bf ("IB/cm: Do not queue work to a device that's going away") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The commit 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).
Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.
Fixes: 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mans Rullgard <mans@mansr.com> Tested-by: Mans Rullgard <mans@mansr.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f29fd4 ("dmaengine/dw_dmac: Don't handle block
interrupts"). This re-enables block interrupts so the cyclic callbacks
can work. Other transfer types are not affected as they set the INT_EN
bit only on the last block.
Commit 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.
This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.
Fixes: 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume") Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
ACPI 6.1 clarified that multi-interface dimms require multiple control
region entries (DCRs) per dimm. Previously we were assuming that a
control region is only present when block-data-windows are present.
This implementation was done with an eye to be compatibility with the
looser ACPI 6.0 interpretation of this table.
1/ When coalescing the memory device (MEMDEV) tables for a single dimm,
coalesce on device_handle rather than control region index.
2/ Whenever we disocver a control region with non-zero block windows
re-scan for block-data-window (BDW) entries.
We may need to revisit this if a DIMM ever implements a format interface
outside of blk or pmem, but that is not on the foreseeable horizon.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The quirk to get "acpi_backlight=vendor" behavior by default on the
Dell Inspiron 5737 was added before we started doing
"acpi_backlight=native" by default on Win8 ready machines.
Since we now avoid using acpi-video as backlight driver on these machines
by default (using the native driver instead) we no longer need this quirk.
Moreover the vendor driver does not work after a suspend/resume where
as the native driver does.
This reverts commit 08a56226d847 (ACPI / video: Add Dell Inspiron 5737
to the blacklist).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111061 Reported-and-tested-by: erusan@gmail.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The Toshiba Satellite R830 needs disable_backlight_sysfs_if=1, just like
the Toshiba Portege R830. Add a quirk for this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=21012 Tested-by: To Do <entodoays@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The Toshiba Portege R700 needs disable_backlight_sysfs_if=1, just like
the Toshiba Portege R830. Add a quirk for this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=21012 Tested-by: Emma Reisz <emmareisz@outlook.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The sw842 library code was merged in linux-4.1 and causes a very rare randconfig
failure when CONFIG_CRC32 is not set:
lib/built-in.o: In function `sw842_compress':
oid_registry.c:(.text+0x12ddc): undefined reference to `crc32_be'
lib/built-in.o: In function `sw842_decompress':
oid_registry.c:(.text+0x137e4): undefined reference to `crc32_be'
This adds an explict 'select CRC32' statement, similar to what the other users
of the crc32 code have. In practice, CRC32 is always enabled anyway because
over 100 other symbols select it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 2da572c959dd ("lib: add software 842 compression/decompression") Acked-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 9d99a8dda154 ("nvme: move hardware structures out of the uapi
version of nvme.h") renamed nvme.h to nvme_ioctl.h, but the uapi list
still refers to nvme.h. People trying to install the headers hit a
failure as the header no longer exists.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
Tested-by: <dinyar.rabady+spam@gmail.com> Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
One of the newest ideapad models also lacks a physical hw rfkill switch,
and trying to read the hw rfkill switch through the ideapad module
causes it to always reported blocking breaking wifi.
Fix it by adding this model to the DMI list.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If transflective backlight is supported and the brightness is zero
(lowest brightness level), the set_lcd_brightness function will activate
the transflective backlight, making the LCD appear to be turned off.
This patch fixes the issue by incrementing the brightness level, and
by doing so, avoiding the activation of the tranflective backlight.
Reported-and-tested-by: Fabian Koester <fabian.koester@bringnow.com> Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Limit the amount of time radeon_flip_work_func can
delay programming a page flip, by both limiting the
maximum amount of time per wait cycle and the maximum
number of wait cycles. Continue the flip if the limit
is exceeded, even if that may result in a visual or
timing glitch.
This is to prevent a hang of page flips, as reported
in fdo bug #93746: Disconnecting a DisplayPort display
in parallel to a kms pageflip getting queued can cause
the following hang of page flips and thereby an unusable
desktop:
2. Hotunplug of display causes the driver to DPMS OFF
the unplugged display. Display engine shuts down,
scanout no longer moves, but stays at its resting
position at start line of vblank.
3. radeon_flip_work_func executes while crtc is off, and
due to the non-moving scanout position, the new flip
delay code introduced into Linux 4.4 by
commit 5b5561b3660d ("drm/radeon: Fixup hw vblank counter/ts..")
enters an infinite wait loop.
4. After reconnecting the display, the pageflip continues
to hang in 3. and the display doesn't update its view
of the desktop.
This patch fixes the Linux 4.4 regression from fdo bug #93746
drm_vblank_offdelay can have three different types of values:
< 0 is to be always treated the same as dev->vblank_disable_immediate
= 0 is to be treated as "never disable vblanks"
> 0 is to be treated as disable immediate if kms driver wants it
that way via dev->vblank_disable_immediate. Otherwise it is
a disable timeout in msecs.
This got broken in Linux 3.18+ for the implementation of
drm_vblank_on. If the user specified a value of zero which should
always reenable vblank irqs in this function, a kms driver could
override the users choice by setting vblank_disable_immediate
to true. This patch fixes the regression and keeps the user in
control.
v2: Only reenable vblank if there are clients left or the user
requested to "never disable vblanks" via offdelay 0. Enabling
vblanks even in the "delayed disable" case (offdelay > 0) was
specifically added by Ville in commit cd19e52aee922
("drm: Kick start vblank interrupts at drm_vblank_on()"),
but after discussion it turns out that this was done by accident.
Citing Ville: "I think it just ended up as a mess due to changing
some of the semantics of offdelay<0 vs. offdelay==0 vs.
disable_immediate during the review of the series. So yeah, given
how drm_vblank_put() works now, I'd just make this check for
offdelay==0."
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Changes to drm_update_vblank_count() in Linux 4.4 broke the
behaviour of the pre/post modeset functions as the new update
code doesn't deal with hw vblank counter resets inbetween calls
to drm_vblank_pre_modeset an drm_vblank_post_modeset, as it
should.
This causes mistreatment of such hw counter resets as counter
wraparound, and thereby large forward jumps of the software
vblank counter which in turn cause vblank event dispatching
and vblank waits to fail/hang --> userspace clients hang.
This symptom was reported on radeon-kms to cause a infinite
hang of KDE Plasma 5 shell's login procedure, preventing users
from logging in.
Fix this by detecting when drm_update_vblank_count() is called
inside a pre->post modeset interval. If so, clamp valid vblank
increments to the safe values 0 and 1, pretty much restoring
the update behavior of the old update code of Linux 4.3 and
earlier. Also reset the last recorded hw vblank count at call
to drm_vblank_post_modeset() to be safe against hw that after
modesetting, dpms on etc. only fires its first vblank irq after
drm_vblank_post_modeset() was already called.
This fixes a regression introduced by the new drm_update_vblank_count()
implementation in Linux 4.4:
Restrict the bump of the software vblank counter in drm_update_vblank_count()
to a safe maximum value of +1 whenever there is the possibility that
concurrent readers of vblank timestamps could be active at the moment,
as the current implementation of the timestamp caching and updating is
not safe against concurrent readers for calls to store_vblank() with a
bump of anything but +1. A bump != 1 would very likely return corrupted
timestamps to userspace, because the same slot in the cache could
be concurrently written by store_vblank() and read by one of those
readers in a non-atomic fashion and without the read-retry logic
detecting this collision.
Concurrent readers can exist while drm_update_vblank_count() is called
from the drm_vblank_off() or drm_vblank_on() functions or other non-vblank-
irq callers. However, all those calls are happening with the vbl_lock
locked thereby preventing a drm_vblank_get(), so the vblank refcount
can't increase while drm_update_vblank_count() is executing. Therefore
a zero vblank refcount during execution of that function signals that
is safe for arbitrary counter bumps if called from outside vblank irq,
whereas a non-zero count is not safe.
Whenever the function is called from vblank irq, we have to assume concurrent
readers could show up any time during its execution, even if the refcount
is currently zero, as vblank irqs are usually only enabled due to the
presence of readers, and because when it is called from vblank irq it
can't hold the vbl_lock to protect it from sudden bumps in vblank refcount.
Therefore also restrict bumps to +1 when the function is called from vblank
irq.
Such bumps of more than +1 can happen at other times than reenabling
vblank irqs, e.g., when regular vblank interrupts get delayed by more
than 1 frame due to long held locks, long irq off periods, realtime
preemption on RT kernels, or system management interrupts.
A better solution would be to rewrite the timestamp caching to use
full seqlocks to allow concurrent writes and reads for arbitrary
vblank counter increments.
v2: Add code comment that this is essentially a hack and should
be replaced by a full seqlock implementation for caching of
timestamps.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Otherwise if a kms driver calls into drm_vblank_off() more than once
before calling drm_vblank_on() again, the redundant calls to
vblank_disable_and_save() will call drm_update_vblank_count()
while hw vblank counters and vblank timestamping are in a undefined
state during modesets, dpms off etc.
At least with the legacy drm helpers it is not unusual to
get multiple calls to drm_vblank_off and drm_vblank_on, e.g.,
half a dozen calls to drm_vblank_off and two calls to drm_vblank_on
were observed on radeon-kms during dpms-off -> dpms-on transition.
We don't no-op calls from atomic modesetting drivers, as they
should do a proper job of tracking hw state.
Fixes large jumps of the software maintained vblank counter due to
the hardware vblank counter resetting to zero during dpms off or
modeset, e.g., if radeon-kms is modified to use drm_vblank_off/on
instead of drm_vblank_pre/post_modeset().
This fixes a regression caused by the changes made to
drm_update_vblank_count() in Linux 4.4.
v2: Don't no-op on atomic modesetting drivers, per suggestion
of Daniel Vetter.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: michel@daenzer.net Cc: vbabka@suse.cz Cc: ville.syrjala@linux.intel.com Cc: alexander.deucher@amd.com Cc: christian.koenig@amd.com Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a
result we skip assigning a DPLL to any DP MST ports, which makes link
training fail:
[ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well
[ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well
[ 1442.933957] [drm:intel_mst_pre_enable_dp] 0
[ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000
[ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0
[ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0
[ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000
[ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1
[ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1
[ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000
[ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2
…
[ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up
[ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting
After which the pipe state goes completely out of sync:
[ 70.075596] [drm:check_crtc_state] [CRTC:25]
[ 70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001)
[ 70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0)
[ 70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021)
[ 70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173)
[ 70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5)
[ 70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256)
[ 70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500)
And if you're especially lucky, it keeps going downhill:
On SKL+ plane scaling is mutually exclusive with color keying. The code
check for this, but during some refactoring the code got changed to
also reject primary plane windowing when color keying is used. There is
no such restriction in the hardware, so restore the original logic.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: 061e4b8d650a ("drm/i915: clean up atomic plane check functions, v2.") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452883613-28549-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 693bdc28a733dba68b86af295e7509812fec35d9) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
We need to set the DC FLUSH PIPE_CONTROL bit on Gen7+ to guarantee
that writes performed via the HDC are visible in memory. Fixes an
intermittent failure in a Piglit test that writes to a BO from a
shader using GL atomic counters (implemented as HDC untyped atomics)
and then expects the memory to read back the same value after mapping
it on the CPU.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91298 Tested-by: Mark Janes <mark.a.janes@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452740379-3194-1-git-send-email-currojerez@riseup.net
(cherry picked from commit 965fd602a6436f689f4f2fe40a6789582778ccd5) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
gmbus also needs the power domain infrastructure right from the start,
since as soon as we register the i2c controllers someone can use them.
v2: Adjust cleanup paths too (Chris).
v3: Rebase onto -nightly (totally bogus tree I had lying around) and
also move dpio init head (Ville).
v4: Ville instead suggested to move gmbus setup later in the sequence,
since it's only needed by the modeset code.
v5: Move even close to the actual user, right next to the comment that
states where we really need gmbus (and interrupts!).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Meelis Roos <mroos@linux.ee> Cc: Chris Wilson <chris@chris-wilson.co.uk> Fixes: ac9b8236551d ("drm/i915: Introduce a gmbus power domain")
References: http://www.spinics.net/lists/intel-gfx/msg83075.html Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452682528-19437-1-git-send-email-daniel.vetter@ffwll.ch Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This fixes reprobing of display connectors on resume. After some
talking with danvet on IRC, I learned that calling
drm_helper_hpd_irq_event() does actually trigger a full reprobe of each
connector's status. It turns out this is the actual reason reprobing on
resume hasn't been working (this was observed on a T440s):
- We call hpd_init()
- We check each connector for a couple of things before marking
connector->polled with DRM_CONNECTOR_POLL_HPD, one of which is an
active encoder. Of course, a disconnected port won't have an
active encoder, so we don't add the flag to any of the
connectors.
- We call drm_helper_hpd_irq_event()
- drm_helper_irq_event() checks each connector for the
DRM_CONNECTOR_POLL_HPD flag. The only one that has it is eDP-1,
so we skip reprobing each connector except that one.
In addition, we also now avoid setting connector->polled to
DRM_CONNECTOR_POLL_HPD for MST connectors, since their reprobing is
handled by the mst helpers. This is probably what was originally
intended to happen here.
Changes since V1:
* Use the explanation of the issue as the commit message instead
* Change the title of the commit, since this does more then just stop a
check for an encoder now
* Add "Fixes" line for the patch that introduced this regression
* Don't enable DRM_CONNECTOR_POLL_HPD for mst connectors
Changes since V2:
* Put patch changelog above Signed-off-by
* Follow Daniel Vetter's suggestion for making the code here a bit more
legible
Following a GPU reset, we may leave the context in a poorly defined
state, and reloading from that context will leave the GPU flummoxed. For
secondary contexts, this will lead to that context being banned - but
currently it is also causing the default context to become banned,
leading to turmoil in the shared state.
which quietly introduced the removal of the MI_RESTORE_INHIBIT on the
default context.
v2: Mark the global default context as uninitialized on GPU reset so
that the context-local workarounds are reloaded upon re-enabling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448630935-27377-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: This seems to fix a gpu hand on after the first resume,
resulting in any future suspend operation failing with -EIO because
the gpu seems to be in a funky state. Somehow this patch fixes that.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 42f1cae8c079bcceb3cff079fddc3ff8852c788f) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Properly setup the DFS divider for DP audio for DCE4.1.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Move encoding of DFS (digital frequency synthesizer) divider into a
separate function and improve calculation precision.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This is preparation for the fixes in the following patches.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Firmware is LE. Need to properly byteswap some of the fields
so they are interpreted correctly by the driver on BE systems.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
eoffset is sometimes treated as the last address inside the address
range, and sometimes as the first address outside the range. This
was resulting in errors when a test filled up the entire address
space. Make it consistent to always be the last address within the
range. Also fixed related errors when checking the VA limit and in
radeon_vm_fence_pts.
Signed-off-by: Felix.Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This is needed to properly deallocate port payload
after downstream branch get unplugged.
In order to do this unplugged MST topology should
be preserved, to find first alive port on path to
unplugged MST topology, and send payload deallocation
request to branch device of found port.
For this mstb and port kref's are used in reversed
order to track when port and branch memory could be
freed.
Added additional functions to find appropriate mstb
as described above.
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
drivers/gpu/drm/drm_dp_mst_topology.c
Previous implementation does not handle case below: boot up one MST branch
to DP connector of ASIC. After boot up, hot plug 2nd MST branch to DP output
of 1st MST, GUID is not created for 2nd MST branch. When downstream port of
2nd MST branch send upstream request, it fails because 2nd MST branch GUID
is not available.
New Implementation: only create GUID for MST branch and save it within Branch.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Our PBN value overflows the 20 bits integer part of the 20.12
fixed point. We need to use 31.32 fixed point to avoid this.
This happens with display clocks larger than 293122 (at 24 bpp),
which we see with the Sharp (and similar) 4k tiled displays.
Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
drm_fixp_from_fraction allows us to create a fixed point directly
from a fraction, rather than creating fixed point values and dividing
later. This avoids overflow of our 64 bit value for large numbers.
drm_fixp2int_ceil allows us to return the ceiling of our fixed point
value.
[airlied: squash Jordan's fix]
32-bit-build-fix: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In case broadcast message received in UP request,
RAD cannot be used to identify message originator.
Message should be parsed, originator should be found
by GUID from parsed message.
Also reply with broadcast in case broadcast message
received (for now it is always broadcast)
Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In the display resume path, move the calls to drm_vblank_on()
after the point when the display engine is running again.
Since changes were made to drm_update_vblank_count() in Linux 4.4+
to emulate hw vblank counters via vblank timestamping, the function
drm_vblank_on() now needs working high precision vblank timestamping
and therefore working scanout position queries at time of call.
These don't work before the display engine gets restarted, causing
miscalculation of vblank counter increments and thereby large forward
jumps in vblank count at display resume. These jumps can cause client
hangs on resume, or desktop hangs in the case of composited desktops.
Fix this Linux 4.4 regression by reordering calls accordingly.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: ville.syrjala@linux.intel.com Cc: daniel.vetter@ffwll.ch Cc: dri-devel@lists.freedesktop.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This is a port of the same fix for radeon-kms in the
patch "drm/radeon: Don't hang in radeon_flip_work_func
on disabled crtc. (v2)"
Limit the amount of time amdgpu_flip_work_func can
delay programming a page flip, by both limiting the
maximum amount of time per wait cycle and the maximum
number of wait cycles. Continue the flip if the limit
is exceeded, even if that may result in a visual or
timing glitch.
This is to prevent a hang of page flips, as reported
in fdo bug #93746: Disconnecting a DisplayPort display
in parallel to a kms pageflip getting queued can cause
the following hang of page flips and thereby an unusable
desktop:
2. Hotunplug of display causes the driver to DPMS OFF
the unplugged display. Display engine shuts down,
scanout no longer moves, but stays at its resting
position at start line of vblank.
3. amdgpu_flip_work_func executes while crtc is off, and
due to the non-moving scanout position, the new flip
delay code introduced into Linux 4.4 by
commit 8e36f9d33c13 ("drm/amdgpu: Fixup hw vblank counter/ts..")
enters an infinite wait loop.
4. After reconnecting the display, the pageflip continues
to hang in 3. and the display doesn't update its view
of the desktop.
This patch fixes the Linux 4.4 regression from fdo bug #93746
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Otherwise we could try to evict overlapping userptr BOs in get_user_pages(),
leading to a possible circular locking dependency.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
An arbitrary amount of time can pass between spin_unlock and
fence_wait_any_timeout, so we need to ensure that nobody frees the
fences from under us.
A stress test (rapidly starting and killing hundreds of glxgears
instances) ran into a deadlock in fence_wait_any_timeout after
about an hour, and this race condition appears to be a plausible
cause.
v2: agd: rebase on upstream
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>