Dmytro Linkin [Fri, 14 May 2021 08:14:19 +0000 (11:14 +0300)]
net/mlx5e: Don't create devices during unload flow
Running devlink reload command for port in switchdev mode cause
resources to corrupt: driver can't release allocated EQ and reclaim
memory pages, because "rdma" auxiliary device had add CQs which blocks
EQ from deletion.
Erroneous sequence happens during reload-down phase, and is following:
1. detach device - suspends auxiliary devices which support it, destroys
others. During this step "eth-rep" and "rdma-rep" are destroyed,
"eth" - suspended.
2. disable SRIOV - moves device to legacy mode; as part of disablement -
rescans drivers. This step adds "rdma" auxiliary device.
3. destroy EQ table - <failure>.
Driver shouldn't create any device during unload flows. To handle that
implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset
on device attach. If flag is set do no-op on drivers rescan.
Fixes: a925b5e309c9 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus") Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Decapsulation L3 on small inner packets which are less than
64 Bytes was done incorrectly. In small packets there is an
extra padding added in L2 which should not be included in L3
length. The issue was that after decapL3 the extra L2 padding
caused an update on the L3 length.
To avoid this issue the new header is pushed to the beginning
of the packet (offset 0) which should not cause a HW reparse
and update the L3 length.
Parav Pandit [Tue, 8 Jun 2021 16:03:24 +0000 (19:03 +0300)]
net/mlx5: E-Switch, Allow setting GUID for host PF vport
E-switch should be able to set the GUID of host PF vport.
Currently it returns an error. This results in below error
when user attempts to configure MAC address of the PF of an
external controller.
$ devlink port function set pci/0000:03:00.0/196608 \
hw_addr 00:00:00:11:22:33
mlx5_core 0000:03:00.0: mlx5_esw_set_vport_mac_locked:1876:(pid 6715):\
"Failed to set vport 0 node guid, err = -22.
RDMA_CM will not function properly for this VF."
Check for zero vport is no longer needed.
Fixes: 330077d14de1 ("net/mlx5: E-switch, Supporting setting devlink port function mac address") Signed-off-by: Yuval Avnery <yuvalav@nvidia.com> Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Bodong Wang <bodong@nvidia.com> Reviewed-by: Alaa Hleihel <alaa@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit [Tue, 8 Jun 2021 16:14:08 +0000 (19:14 +0300)]
net/mlx5: E-Switch, Read PF mac address
External controller PF's MAC address is not read from the device during
vport setup. Fail to read this results in showing all zeros to user
while the factory programmed MAC is a valid value.
Leon Romanovsky [Sun, 21 Mar 2021 17:57:14 +0000 (19:57 +0200)]
net/mlx5: Check that driver was probed prior attaching the device
The device can be requested to be attached despite being not probed.
This situation is possible if devlink reload races with module removal,
and the following kernel panic is an outcome of such race.
Kees Cook [Wed, 16 Jun 2021 19:53:59 +0000 (12:53 -0700)]
r8169: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 16 Jun 2021 19:53:33 +0000 (12:53 -0700)]
sh_eth: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 16 Jun 2021 19:53:03 +0000 (12:53 -0700)]
r8152: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Wed, 16 Jun 2021 14:57:27 +0000 (16:57 +0200)]
selftests: net: use bash to run udpgro_fwd test case
udpgro_fwd.sh contains many bash specific operators ("[[", "local -r"),
but it's using /bin/sh; in some distro /bin/sh is mapped to /bin/dash,
that doesn't support such operators.
Force the test to use /bin/bash explicitly and prevent false positive
test failures.
Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 14:47:15 +0000 (07:47 -0700)]
net/af_unix: fix a data-race in unix_dgram_sendmsg / unix_release_sock
While unix_may_send(sk, osk) is called while osk is locked, it appears
unix_release_sock() can overwrite unix_peer() after this lock has been
released, making KCSAN unhappy.
Changing unix_release_sock() to access/change unix_peer()
before lock is released should fix this issue.
BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock
write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1:
unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558
unix_release+0x2f/0x50 net/unix/af_unix.c:859
__sock_release net/socket.c:599 [inline]
sock_close+0x6c/0x150 net/socket.c:1258
__fput+0x25b/0x4e0 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0xae/0x130 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302
do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0:
unix_may_send net/unix/af_unix.c:189 [inline]
unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff888167905400 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Wed, 16 Jun 2021 14:03:21 +0000 (16:03 +0200)]
selftests: net: veth: make test compatible with dash
veth.sh is a shell script that uses /bin/sh; some distro (Ubuntu for
example) use dash as /bin/sh and in this case the test reports the
following error:
# ./veth.sh: 21: local: -r: bad variable name
# ./veth.sh: 21: local: -r: bad variable name
This happens because dash doesn't support the option "-r" with local.
Moreover, in case of missing bpf object, the script is exiting -1, that
is an illegal number for dash:
exit: Illegal number: -1
Change the script to be compatible both with bash and dash and prevent
the errors above.
Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 13:42:02 +0000 (06:42 -0700)]
net/packet: annotate accesses to po->ifindex
Like prior patch, we need to annotate lockless accesses to po->ifindex
For instance, packet_getname() is reading po->ifindex (twice) while
another thread is able to change po->ifindex.
KCSAN reported:
BUG: KCSAN: data-race in packet_do_bind / packet_getname
write to 0xffff888143ce3cbc of 4 bytes by task 25573 on cpu 1:
packet_do_bind+0x420/0x7e0 net/packet/af_packet.c:3191
packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
__sys_bind+0x200/0x290 net/socket.c:1637
__do_sys_bind net/socket.c:1648 [inline]
__se_sys_bind net/socket.c:1646 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1646
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888143ce3cbc of 4 bytes by task 25578 on cpu 0:
packet_getname+0x5b/0x1a0 net/packet/af_packet.c:3525
__sys_getsockname+0x10e/0x1a0 net/socket.c:1887
__do_sys_getsockname net/socket.c:1902 [inline]
__se_sys_getsockname net/socket.c:1899 [inline]
__x64_sys_getsockname+0x3e/0x50 net/socket.c:1899
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25578 Comm: syz-executor.5 Not tainted 5.13.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 13:42:01 +0000 (06:42 -0700)]
net/packet: annotate accesses to po->bind
tpacket_snd(), packet_snd(), packet_getname() and packet_seq_show()
can read po->num without holding a lock. This means other threads
can change po->num at the same time.
KCSAN complained about this known fact [1]
Add READ_ONCE()/WRITE_ONCE() to address the issue.
[1] BUG: KCSAN: data-race in packet_do_bind / packet_sendmsg
write to 0xffff888131a0dcc0 of 2 bytes by task 24714 on cpu 0:
packet_do_bind+0x3ab/0x7e0 net/packet/af_packet.c:3181
packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
__sys_bind+0x200/0x290 net/socket.c:1637
__do_sys_bind net/socket.c:1648 [inline]
__se_sys_bind net/socket.c:1646 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1646
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888131a0dcc0 of 2 bytes by task 24719 on cpu 1:
packet_snd net/packet/af_packet.c:2899 [inline]
packet_sendmsg+0x317/0x3570 net/packet/af_packet.c:3040
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2433
__do_sys_sendmsg net/socket.c:2442 [inline]
__se_sys_sendmsg net/socket.c:2440 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2440
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000 -> 0x1200
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24719 Comm: syz-executor.5 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 24803f38a5c0 ("igmp: do not remove igmp souce list info when set
link down"), the ip_mc_clear_src() in ip_mc_destroy_dev() was removed,
because it was also called in igmpv3_clear_delrec().
However, ip_mc_clear_src() called in igmpv3_clear_delrec() doesn't
release in_dev->mc_list->sources. And RCU_INIT_POINTER() assigns the
NULL to dev->ip_ptr. As a result, in_dev cannot be obtained through
inetdev_by_index() and then in_dev->mc_list->sources cannot be released
by ip_mc_del1_src() in the sock_close. Rough call sequence goes like:
So we still need to call ip_mc_clear_src() in ip_mc_destroy_dev() to free
in_dev->mc_list->sources.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info ...") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Chengyang Fan <cy.fan@huawei.com> Acked-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang [Wed, 16 Jun 2021 09:14:26 +0000 (17:14 +0800)]
net: fec_ptp: fix issue caused by refactor the fec_devtype
Commit da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.
Fixes: da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dongliang Mu [Wed, 16 Jun 2021 02:48:33 +0000 (10:48 +0800)]
net: usb: fix possible use-after-free in smsc75xx_bind
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang [Wed, 16 Jun 2021 09:10:24 +0000 (17:10 +0800)]
net: stmmac: disable clocks in stmmac_remove_config_dt()
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Skripkin [Wed, 9 Jun 2021 21:58:33 +0000 (00:58 +0300)]
can: mcba_usb: fix memory leak in mcba_usb
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Norbert Slusarek [Sat, 12 Jun 2021 20:18:54 +0000 (22:18 +0200)]
can: bcm: fix infoleak in struct bcm_msg_head
On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between
struct members count and ival1. Even though all struct members are initialized,
the 4-byte hole will contain data from the kernel stack. This patch zeroes out
struct bcm_msg_head before usage, preventing infoleaks to userspace.
Tetsuo Handa [Sat, 5 Jun 2021 10:26:35 +0000 (19:26 +0900)]
can: bcm/raw/isotp: use per module netdevice notifier
syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.
Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.
Oleksij Rempel [Fri, 21 May 2021 11:57:20 +0000 (13:57 +0200)]
can: j1939: fix Use-after-Free, hold skb ref while in use
This patch fixes a Use-after-Free found by the syzbot.
The problem is that a skb is taken from the per-session skb queue,
without incrementing the ref count. This leads to a Use-after-Free if
the skb is taken concurrently from the session queue due to a CTS.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/r/20210521115720.7533-1-o.rempel@pengutronix.de Cc: Hillf Danton <hdanton@sina.com> Cc: linux-stable <stable@vger.kernel.org> Reported-by: syzbot+220c1a29987a9a490903@syzkaller.appspotmail.com Reported-by: syzbot+45199c1b73b4013525cf@syzkaller.appspotmail.com Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
lantiq: net: fix duplicated skb in rx descriptor ring
The previous commit didn't fix the bug properly. By mistake, it replaces
the pointer of the next skb in the descriptor ring instead of the current
one. As a result, the two descriptors are assigned the same SKB. The error
is seen during the iperf test when skb_put tries to insert a second packet
and exceeds the available buffer.
Fixes: c7718ee96dbc ("net: lantiq: fix memory corruption in RX ring ") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Kristian Evensen [Tue, 15 Jun 2021 10:01:51 +0000 (12:01 +0200)]
qmi_wwan: Do not call netif_rx from rx_fixup
When the QMI_WWAN_FLAG_PASS_THROUGH is set, netif_rx() is called from
qmi_wwan_rx_fixup(). When the call to netif_rx() is successful (which is
most of the time), usbnet_skb_return() is called (from rx_process()).
usbnet_skb_return() will then call netif_rx() a second time for the same
skb.
Simplify the code and avoid the redundant netif_rx() call by changing
qmi_wwan_rx_fixup() to always return 1 when QMI_WWAN_FLAG_PASS_THROUGH
is set. We then leave it up to the existing infrastructure to call
netif_rx().
Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 4d06dd537f95 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind") Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 14 Jun 2021 22:24:05 +0000 (15:24 -0700)]
ptp: improve max_adj check against unreasonable values
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511cd ("ptp: validate the requested frequency adjustment.") Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 31 May 2021 12:34:24 +0000 (12:34 +0000)]
bpf, selftests: Adjust few selftest outcomes wrt unreachable code
In almost all cases from test_verifier that have been changed in here, we've
had an unreachable path with a load from a register which has an invalid
address on purpose. This was basically to make sure that we never walk this
path and to have the verifier complain if it would otherwise. Change it to
match on the right error for unprivileged given we now test these paths
under speculative execution.
There's one case where we match on exact # of insns_processed. Due to the
extra path, this will of course mismatch on unprivileged. Thus, restrict the
test->insn_processed check to privileged-only.
In one other case, we result in a 'pointer comparison prohibited' error. This
is similarly due to verifying an 'invalid' branch where we end up with a value
pointer on one side of the comparison.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 28 May 2021 15:47:32 +0000 (15:47 +0000)]
bpf: Fix leakage under speculation on mispredicted branches
The verifier only enumerates valid control-flow paths and skips paths that
are unreachable in the non-speculative domain. And so it can miss issues
under speculative execution on mispredicted branches.
For example, a type confusion has been demonstrated with the following
crafted program:
// r0 = pointer to a map array entry
// r6 = pointer to readable stack slot
// r9 = scalar controlled by attacker
1: r0 = *(u64 *)(r0) // cache miss
2: if r0 != 0x0 goto line 4
3: r6 = r9
4: if r0 != 0x1 goto line 6
5: r9 = *(u8 *)(r6)
6: // leak r9
Since line 3 runs iff r0 == 0 and line 5 runs iff r0 == 1, the verifier
concludes that the pointer dereference on line 5 is safe. But: if the
attacker trains both the branches to fall-through, such that the following
is speculatively executed ...
r6 = r9
r9 = *(u8 *)(r6)
// leak r9
... then the program will dereference an attacker-controlled value and could
leak its content under speculative execution via side-channel. This requires
to mistrain the branch predictor, which can be rather tricky, because the
branches are mutually exclusive. However such training can be done at
congruent addresses in user space using different branches that are not
mutually exclusive. That is, by training branches in user space ...
A: if r0 != 0x0 goto line C
B: ...
C: if r0 != 0x0 goto line D
D: ...
... such that addresses A and C collide to the same CPU branch prediction
entries in the PHT (pattern history table) as those of the BPF program's
lines 2 and 4, respectively. A non-privileged attacker could simply brute
force such collisions in the PHT until observing the attack succeeding.
Alternative methods to mistrain the branch predictor are also possible that
avoid brute forcing the collisions in the PHT. A reliable attack has been
demonstrated, for example, using the following crafted program:
// r0 = pointer to a [control] map array entry
// r7 = *(u64 *)(r0 + 0), training/attack phase
// r8 = *(u64 *)(r0 + 8), oob address
// [...]
// r0 = pointer to a [data] map array entry
1: if r7 == 0x3 goto line 3
2: r8 = r0
// crafted sequence of conditional jumps to separate the conditional
// branch in line 193 from the current execution flow
3: if r0 != 0x0 goto line 5
4: if r0 == 0x0 goto exit
5: if r0 != 0x0 goto line 7
6: if r0 == 0x0 goto exit
[...]
187: if r0 != 0x0 goto line 189
188: if r0 == 0x0 goto exit
// load any slowly-loaded value (due to cache miss in phase 3) ...
189: r3 = *(u64 *)(r0 + 0x1200)
// ... and turn it into known zero for verifier, while preserving slowly-
// loaded dependency when executing:
190: r3 &= 1
191: r3 &= 2
// speculatively bypassed phase dependency
192: r7 += r3
193: if r7 == 0x3 goto exit
194: r4 = *(u8 *)(r8 + 0)
// leak r4
As can be seen, in training phase (phase != 0x3), the condition in line 1
turns into false and therefore r8 with the oob address is overridden with
the valid map value address, which in line 194 we can read out without
issues. However, in attack phase, line 2 is skipped, and due to the cache
miss in line 189 where the map value is (zeroed and later) added to the
phase register, the condition in line 193 takes the fall-through path due
to prior branch predictor training, where under speculation, it'll load the
byte at oob address r8 (unknown scalar type at that point) which could then
be leaked via side-channel.
One way to mitigate these is to 'branch off' an unreachable path, meaning,
the current verification path keeps following the is_branch_taken() path
and we push the other branch to the verification stack. Given this is
unreachable from the non-speculative domain, this branch's vstate is
explicitly marked as speculative. This is needed for two reasons: i) if
this path is solely seen from speculative execution, then we later on still
want the dead code elimination to kick in in order to sanitize these
instructions with jmp-1s, and ii) to ensure that paths walked in the
non-speculative domain are not pruned from earlier walks of paths walked in
the speculative domain. Additionally, for robustness, we mark the registers
which have been part of the conditional as unknown in the speculative path
given there should be no assumptions made on their content.
The fix in here mitigates type confusion attacks described earlier due to
i) all code paths in the BPF program being explored and ii) existing
verifier logic already ensuring that given memory access instruction
references one specific data structure.
An alternative to this fix that has also been looked at in this scope was to
mark aux->alu_state at the jump instruction with a BPF_JMP_TAKEN state as
well as direction encoding (always-goto, always-fallthrough, unknown), such
that mixing of different always-* directions themselves as well as mixing of
always-* with unknown directions would cause a program rejection by the
verifier, e.g. programs with constructs like 'if ([...]) { x = 0; } else
{ x = 1; }' with subsequent 'if (x == 1) { [...] }'. For unprivileged, this
would result in only single direction always-* taken paths, and unknown taken
paths being allowed, such that the former could be patched from a conditional
jump to an unconditional jump (ja). Compared to this approach here, it would
have two downsides: i) valid programs that otherwise are not performing any
pointer arithmetic, etc, would potentially be rejected/broken, and ii) we are
required to turn off path pruning for unprivileged, where both can be avoided
in this work through pushing the invalid branch to the verification stack.
The issue was originally discovered by Adam and Ofek, and later independently
discovered and reported as a result of Benedict and Piotr's research work.
Fixes: b2157399cc98 ("bpf: prevent out-of-bounds speculation") Reported-by: Adam Morrison <mad@cs.tau.ac.il> Reported-by: Ofek Kirzner <ofekkir@gmail.com> Reported-by: Benedict Schlueter <benedict.schlueter@rub.de> Reported-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 28 May 2021 13:47:27 +0000 (13:47 +0000)]
bpf: Do not mark insn as seen under speculative path verification
... in such circumstances, we do not want to mark the instruction as seen given
the goal is still to jmp-1 rewrite/sanitize dead code, if it is not reachable
from the non-speculative path verification. We do however want to verify it for
safety regardless.
With the patch as-is all the insns that have been marked as seen before the
patch will also be marked as seen after the patch (just with a potentially
different non-zero count). An upcoming patch will also verify paths that are
unreachable in the non-speculative domain, hence this extension is needed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 28 May 2021 13:03:30 +0000 (13:03 +0000)]
bpf: Inherit expanded/patched seen count from old aux data
Instead of relying on current env->pass_cnt, use the seen count from the
old aux data in adjust_insn_aux_data(), and expand it to the new range of
patched instructions. This change is valid given we always expand 1:n
with n>=1, so what applies to the old/original instruction needs to apply
for the replacement as well.
Not relying on env->pass_cnt is a prerequisite for a later change where we
want to avoid marking an instruction seen when verified under speculative
execution path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Pavel Skripkin [Mon, 14 Jun 2021 12:06:50 +0000 (15:06 +0300)]
net: qrtr: fix OOB Read in qrtr_endpoint_post
Syzbot reported slab-out-of-bounds Read in
qrtr_endpoint_post. The problem was in wrong
_size_ type:
if (len != ALIGN(size, 4) + hdrlen)
goto err;
If size from qrtr_hdr is 4294967293 (0xfffffffd), the result of
ALIGN(size, 4) will be 0. In case of len == hdrlen and size == 4294967293
in header this check won't fail and
skb_put_data(skb, data + hdrlen, size);
will read out of bound from data, which is hdrlen allocated block.
Fixes: 194ccc88297a ("net: qrtr: Support decoding incoming v2 packets") Reported-and-tested-by: syzbot+1917d778024161609247@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 13 Jun 2021 00:24:59 +0000 (18:24 -0600)]
ipv4: Fix device used for dst_alloc with local routes
Oliver reported a use case where deleting a VRF device can hang
waiting for the refcnt to drop to 0. The root cause is that the dst
is allocated against the VRF device but cached on the loopback
device.
The use case (added to the selftests) has an implicit VRF crossing
due to the ordering of the FIB rules (lookup local is before the
l3mdev rule, but the problem occurs even if the FIB rules are
re-ordered with local after l3mdev because the VRF table does not
have a default route to terminate the lookup). The end result is
is that the FIB lookup returns the loopback device as the nexthop,
but the ingress device is in a VRF. The mismatch causes the dst
alloc against the VRF device but then cached on the loopback.
The fix is to bring the trick used for IPv6 (see ip6_rt_get_dev_rcu):
pick the dst alloc device based the fib lookup result but with checks
that the result has a nexthop device (e.g., not an unreachable or
prohibit entry).
Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant") Reported-by: Oliver Herms <oliver.peter.herms@gmail.com> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Skripkin [Sat, 12 Jun 2021 14:51:22 +0000 (17:51 +0300)]
net: caif: fix memory leak in ldisc_open
Syzbot reported memory leak in tty_init_dev().
The problem was in unputted tty in ldisc_open()
static int ldisc_open(struct tty_struct *tty)
{
...
ser->tty = tty_kref_get(tty);
...
result = register_netdevice(dev);
if (result) {
rtnl_unlock();
free_netdev(dev);
return -ENODEV;
}
...
}
Ser pointer is netdev private_data, so after free_netdev()
this pointer goes away with unputted tty reference. So, fix
it by adding tty_kref_put() before freeing netdev.
Reported-and-tested-by: syzbot+f303e045423e617d2cad@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Sat, 12 Jun 2021 13:50:44 +0000 (19:20 +0530)]
cxgb4: fix wrong ethtool n-tuple rule lookup
The TID returned during successful filter creation is relative to
the region in which the filter is created. Using it directly always
returns Hi Prio/Normal filter region's entry for the first couple of
entries, even though the rule is actually inserted in Hash region.
Fix by analyzing in which region the filter has been inserted and
save the absolute TID to be used for lookup later.
Fixes: db43b30cd89c ("cxgb4: add ethtool n-tuple filter deletion") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netxen_nic: Fix an error handling path in 'netxen_nic_probe()'
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: e87ad5539343 ("netxen: support pci error handlers") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix an error handling path in 'qlcnic_probe()'
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 451724c821c1 ("qlcnic: aer support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 12 Jun 2021 01:49:48 +0000 (18:49 -0700)]
ethtool: strset: fix message length calculation
Outer nest for ETHTOOL_A_STRSET_STRINGSETS is not accounted for.
This may result in ETHTOOL_MSG_STRSET_GET producing a warning like:
calculated message payload length (684) not sufficient
WARNING: CPU: 0 PID: 30967 at net/ethtool/netlink.c:369 ethnl_default_doit+0x87a/0xa20
and a splat.
As usually with such warnings three conditions must be met for the warning
to trigger:
- there must be no skb size rounding up (e.g. reply_size of 684);
- string set must be per-device (so that the header gets populated);
- the device name must be at least 12 characters long.
all in all with current user space it looks like reading priv flags
is the only place this could potentially happen. Or with syzbot :)
Reported-by: syzbot+59aa77b92d06cd5a54f2@syzkaller.appspotmail.com Fixes: 71921690f974 ("ethtool: provide string sets with STRSET_GET request") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Fri, 11 Jun 2021 18:26:00 +0000 (13:26 -0500)]
net: qualcomm: rmnet: don't over-count statistics
The purpose of the loop using u64_stats_fetch_*_irq() is to ensure
statistics on a given CPU are collected atomically. If one of the
statistics values gets updated within the begin/retry window, the
loop will run again.
Currently the statistics totals are updated inside that window.
This means that if the loop ever retries, the statistics for the
CPU will be counted more than once.
Fix this by taking a snapshot of a CPU's statistics inside the
protected window, and then updating the counters with the snapshot
values after exiting the loop.
(Also add a newline at the end of this file...)
Fixes: 192c4b5d48f2a ("net: qualcomm: rmnet: Add support for 64 bit stats") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tyson Moore [Sat, 12 Jun 2021 06:54:11 +0000 (02:54 -0400)]
sch_cake: revise docs for RFC 8622 LE PHB support
Commit b8392808eb3fc28e ("sch_cake: add RFC 8622 LE PHB support to CAKE
diffserv handling") added the LE mark to the Bulk tin. Update the
comments to reflect the change.
Signed-off-by: Tyson Moore <tyson@tyson.me> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Changbin Du [Fri, 11 Jun 2021 14:29:59 +0000 (22:29 +0800)]
net: make get_net_ns return error if NET_NS is disabled
There is a panic in socket ioctl cmd SIOCGSKNS when NET_NS is not enabled.
The reason is that nsfs tries to access ns->ops but the proc_ns_operations
is not implemented in this case.
[7.670023] Unable to handle kernel NULL pointer dereference at virtual address 00000010
[7.670268] pgd = 32b54000
[7.670544] [00000010] *pgd=00000000
[7.671861] Internal error: Oops: 5 [#1] SMP ARM
[7.672315] Modules linked in:
[7.672918] CPU: 0 PID: 1 Comm: systemd Not tainted 5.13.0-rc3-00375-g6799d4f2da49 #16
[7.673309] Hardware name: Generic DT based system
[7.673642] PC is at nsfs_evict+0x24/0x30
[7.674486] LR is at clear_inode+0x20/0x9c
The same to tun SIOCGSKNS command.
To fix this problem, we make get_net_ns() return -EINVAL when NET_NS is
disabled. Meanwhile move it to right place net/core/net_namespace.c.
Signed-off-by: Changbin Du <changbin.du@gmail.com> Fixes: c62cce2caee5 ("net: add an ioctl to get a socket network namespace") Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Christian Brauner <christian.brauner@ubuntu.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Fri, 11 Jun 2021 07:16:11 +0000 (15:16 +0800)]
net: stmmac: dwmac1000: Fix extended MAC address registers definition
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Fri, 11 Jun 2021 06:47:47 +0000 (12:17 +0530)]
cxgb4: halt chip before flashing PHY firmware image
When using firmware-assisted PHY firmware image write to flash,
halt the chip before beginning the flash write operation to allow
the running firmware to store the image persistently. Otherwise,
the running firmware will only store the PHY image in local on-chip
RAM, which will be lost after next reset.
Fixes: 4ee339e1e92a ("cxgb4: add support to flash PHY image") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Fri, 11 Jun 2021 06:47:46 +0000 (12:17 +0530)]
cxgb4: fix sleep in atomic when flashing PHY firmware
Before writing new PHY firmware to on-chip memory, driver queries
firmware for current running PHY firmware version, which can result
in sleep waiting for reply. So, move spinlock closer to the actual
on-chip memory write operation, instead of taking it at the callers.
Fixes: 5fff701c838e ("cxgb4: always sync access when flashing PHY firmware") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Fri, 11 Jun 2021 06:47:45 +0000 (12:17 +0530)]
cxgb4: fix endianness when flashing boot image
Boot images are copied to memory and updated with current underlying
device ID before flashing them to adapter. Ensure the updated images
are always flashed in Big Endian to allow the firmware to read the
new images during boot properly.
Fixes: 550883558f17 ("cxgb4: add support to flash boot image") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: ab69bde6b2e9 ("alx: add a simple AR816x/AR817x device driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Praneeth Bajjuri [Thu, 10 Jun 2021 00:43:42 +0000 (19:43 -0500)]
net: phy: dp83867: perform soft reset and retain established link
Current logic is performing hard reset and causing the programmed
registers to be wiped out.
as per datasheet: https://www.ti.com/lit/ds/symlink/dp83867cr.pdf
8.6.26 Control Register (CTRL)
do SW_RESTART to perform a reset not including the registers,
If performed when link is already present,
it will drop the link and trigger re-auto negotiation.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Geet Modi <geet.modi@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The calling function - mptcp_subflow_data_available() - can be invoked
from different contexts:
- plain ssk socket lock
- ssk socket lock + mptcp_data_lock
- ssk socket lock + mptcp_data_lock + msk socket lock.
Since subflow_error_report() tries to acquire the mptcp_data_lock, the
latter two call chains will cause soft lookup.
This change addresses the issue moving the error reporting call to
outer functions, where the held locks list is known and the we can
acquire only the needed one.
Reported-by: Maxim Galaganov <max@internet.ru> Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/199 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 10 Jun 2021 22:59:43 +0000 (15:59 -0700)]
selftests: mptcp: enable syncookie only in absence of reorders
Syncookie validation may fail for OoO packets, causing spurious
resets and self-tests failures, so let's force syncookie only
for tests iteration with no OoO.
Fixes: fed61c4b584c ("selftests: mptcp: make 2nd net namespace use tcp syn cookies unconditionally") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/198 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 10 Jun 2021 22:59:42 +0000 (15:59 -0700)]
mptcp: do not warn on bad input from the network
warn_bad_map() produces a kernel WARN on bad input coming
from the network. Use pr_debug() to avoid spamming the system
log.
Additionally, when the right bound check fails, warn_bad_map() reports
the wrong ssn value, let's fix it.
Fixes: 648ef4b88673 ("mptcp: Implement MPTCP receive path") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/107 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ssk1
skb len = 500 DSS(seq = 1, len=1000, off =500)
# still data_avail == MPTCP_SUBFLOW_DATA_AVAIL,
# as the skb is covered by a pre-existing map,
# which was in-sequence at reception time.
Instead we can explicitly check if some has been received in-sequence,
propagating the info from __mptcp_move_skbs_from_subflow().
Additionally add the 'ONCE' annotation to the 'data_avail' memory
access, as msk will read it outside the subflow socket lock.
Fixes: 648ef4b88673 ("mptcp: Implement MPTCP receive path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 10 Jun 2021 22:59:40 +0000 (15:59 -0700)]
mptcp: try harder to borrow memory from subflow under pressure
If the host is under sever memory pressure, and RX forward
memory allocation for the msk fails, we try to borrow the
required memory from the ingress subflow.
The current attempt is a bit flaky: if skb->truesize is less
than SK_MEM_QUANTUM, the ssk will not release any memory, and
the next schedule will fail again.
Instead, directly move the required amount of pages from the
ssk to the msk, if available
Fixes: 9c3f94e1681b ("mptcp: add missing memory scheduling in the rx path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 10 Jun 2021 21:26:18 +0000 (14:26 -0700)]
Merge branch 'tcp-options-oob-fixes'
Maxim Mikityanskiy says:
====================
Fix out of bounds when parsing TCP options
This series fixes out-of-bounds access in various places in the kernel
where parsing of TCP options takes place. Fortunately, many more
occurrences don't have this bug.
v2 changes:
synproxy: Added an early return when length < 0 to avoid calling
skb_header_pointer with negative length.
sch_cake: Added doff validation to avoid parsing garbage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_cake: Fix out of bounds when parsing TCP options and header
The TCP option parser in cake qdisc (cake_get_tcpopt and
cake_tcph_may_drop) could read one byte out of bounds. When the length
is 1, the execution flow gets into the loop, reads one byte of the
opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads
one more byte, which exceeds the length of 1.
This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
v2 changes:
Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP
header. Although it wasn't strictly an out-of-bounds access (memory was
allocated), garbage values could be read where CAKE expected the TCP
header if doff was smaller than 5.
Cc: Young Xiao <92siuyang@gmail.com> Fixes: 8b7138814f29 ("sch_cake: Add optional ACK filter") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
The TCP option parser in mptcp (mptcp_get_options) could read one byte
out of bounds. When the length is 1, the execution flow gets into the
loop, reads one byte of the opcode, and if the opcode is neither
TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the
length of 1.
This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
Cc: Young Xiao <92siuyang@gmail.com> Fixes: cec37a6e41aa ("mptcp: Handle MP_CAPABLE options for outgoing connections") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: synproxy: Fix out of bounds when parsing TCP options
The TCP option parser in synproxy (synproxy_parse_options) could read
one byte out of bounds. When the length is 1, the execution flow gets
into the loop, reads one byte of the opcode, and if the opcode is
neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds
the length of 1.
This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
v2 changes:
Added an early return when length < 0 to avoid calling
skb_header_pointer with negative length.
Cc: Young Xiao <92siuyang@gmail.com> Fixes: 48b1de4c110a ("netfilter: add SYNPROXY core/target") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 31039 Comm: syz-executor.2 Not tainted 5.13.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 9385 Comm: syz-executor.3 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
These two fixes take care of tunnel_dst problems in the vlan tunnel egress
path. Patch 01 fixes a null ptr deref due to the lockless use of tunnel_dst
pointer without checking it first, and patch 02 fixes a use-after-free
issue due to wrong dst refcounting (dst_clone() -> dst_hold_safe()).
Both fix the same commit and should be queued for stable backports: Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths")
v2: no changes, added stable list to CC
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix vlan tunnel dst refcnt when egressing
The egress tunnel code uses dst_clone() and directly sets the result
which is wrong because the entry might have 0 refcnt or be already deleted,
causing number of problems. It also triggers the WARN_ON() in dst_hold()[1]
when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and
checking if a reference was actually taken before setting the dst.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Yongjun [Thu, 10 Jun 2021 01:41:36 +0000 (09:41 +0800)]
ping: Check return value of function 'ping_queue_rcv_skb'
Function 'ping_queue_rcv_skb' not always return success, which will
also return fail. If not check the wrong return value of it, lead to function
`ping_rcv` return success.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
msg_zerocopy signals if a send operation required copying with a flag
in serr->ee.ee_code.
This field can be incorrect as of the below commit, as a result of
both structs uarg and serr pointing into the same skb->cb[].
uarg->zerocopy must be read before skb->cb[] is reinitialized to hold
serr. Similar to other fields len, hi and lo, use a local variable to
temporarily hold the value.
This was not a problem before, when the value was passed as a function
argument.
Fixes: 75518851a2a0 ("skbuff: Push status and refcounts into sock_zerocopy_callback") Reported-by: Talal Ahmad <talalahmad@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Wed, 26 May 2021 07:40:36 +0000 (10:40 +0300)]
net/mlx5e: Block offload of outer header csum for GRE tunnel
The device is able to offload either the outer header csum or inner
header csum. The driver utilizes the inner csum offload. So, prohibit
setting of tx-gre-csum-segmentation and let it be: off[fixed].
Fixes: 2729984149e6 ("net/mlx5e: Support TSO and TX checksum offloads for GRE tunnels") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Mon, 10 May 2021 11:34:58 +0000 (14:34 +0300)]
net/mlx5e: Block offload of outer header csum for UDP tunnels
The device is able to offload either the outer header csum or inner
header csum. The driver utilizes the inner csum offload. Hence, block
setting of tx-udp_tnl-csum-segmentation and set it to off[fixed].
Fixes: b49663c8fb49 ("net/mlx5e: Add support for UDP tunnel segmentation with outer checksum offload") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Mon, 19 Apr 2021 08:58:31 +0000 (11:58 +0300)]
net/mlx5e: Fix select queue to consider SKBTX_HW_TSTAMP
Steering packets to PTP-SQ should be done only if the SKB has
SKBTX_HW_TSTAMP set in the tx_flags. While here, take the function into
a header and inline it.
Set the whole condition to select the PTP-SQ to unlikely.
Fixes: 24c22dd0918b ("net/mlx5e: Add states to PTP channel") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Thu, 29 Apr 2021 07:03:20 +0000 (10:03 +0300)]
net/mlx5e: Don't update netdev RQs with PTP-RQ
Since the driver opens the PTP-RQ under channel 0, it appears to the
stack as if the SKB was received on rxq0. So from thew stack POV there
are still the same number of RX queues.
Fixes: 960fbfe222a4 ("net/mlx5e: Allow coexistence of CQE compression and HW TS PTP") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Chris Mi [Wed, 28 Apr 2021 11:39:26 +0000 (19:39 +0800)]
net/mlx5e: Verify dev is present in get devlink port ndo
When changing eswitch mode, the netdev is detached from the
hardware resources. So verify dev is present in get devlink
port ndo. Otherwise, we will hit the following panic:
Fixes: 2ff349c5edfe ("net/mlx5e: Verify dev is present in some ndos") Signed-off-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Chris Mi <cmi@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dima Chumak [Wed, 26 May 2021 10:45:10 +0000 (13:45 +0300)]
net/mlx5e: Fix page reclaim for dead peer hairpin
When adding a hairpin flow, a firmware-side send queue is created for
the peer net device, which claims some host memory pages for its
internal ring buffer. If the peer net device is removed/unbound before
the hairpin flow is deleted, then the send queue is not destroyed which
leads to a stack trace on pci device remove:
Fix by destroying the send queue of a hairpin peer net device that is
being removed/unbound, which returns the allocated ring buffer pages to
the host.
Huy Nguyen [Fri, 28 May 2021 18:20:32 +0000 (13:20 -0500)]
net/mlx5e: Remove dependency in IPsec initialization flows
Currently, IPsec feature is disabled because mlx5e_build_nic_netdev
is required to be called after mlx5e_ipsec_init. This requirement is
invalid as mlx5e_build_nic_netdev and mlx5e_ipsec_init initialize
independent resources.
Remove ipsec pointer check in mlx5e_build_nic_netdev so that the
two functions can be called at any order.
Vlad Buslov [Mon, 31 May 2021 13:28:39 +0000 (16:28 +0300)]
net/mlx5e: Fix use-after-free of encap entry in neigh update handler
Function mlx5e_rep_neigh_update() wasn't updated to accommodate rtnl lock
removal from TC filter update path and properly handle concurrent encap
entry insertion/deletion which can lead to following use-after-free:
[23827.464923] ==================================================================
[23827.469446] BUG: KASAN: use-after-free in mlx5e_encap_take+0x72/0x140 [mlx5_core]
[23827.470971] Read of size 4 at addr ffff8881d132228c by task kworker/u20:6/21635
[23827.472251]
[23827.472615] CPU: 9 PID: 21635 Comm: kworker/u20:6 Not tainted 5.13.0-rc3+ #5
[23827.473788] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[23827.475639] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core]
[23827.476731] Call Trace:
[23827.477260] dump_stack+0xbb/0x107
[23827.477906] print_address_description.constprop.0+0x18/0x140
[23827.478896] ? mlx5e_encap_take+0x72/0x140 [mlx5_core]
[23827.479879] ? mlx5e_encap_take+0x72/0x140 [mlx5_core]
[23827.480905] kasan_report.cold+0x7c/0xd8
[23827.481701] ? mlx5e_encap_take+0x72/0x140 [mlx5_core]
[23827.482744] kasan_check_range+0x145/0x1a0
[23827.493112] mlx5e_encap_take+0x72/0x140 [mlx5_core]
[23827.494054] ? mlx5e_tc_tun_encap_info_equal_generic+0x140/0x140 [mlx5_core]
[23827.495296] mlx5e_rep_neigh_update+0x41e/0x5e0 [mlx5_core]
[23827.496338] ? mlx5e_rep_neigh_entry_release+0xb80/0xb80 [mlx5_core]
[23827.497486] ? read_word_at_a_time+0xe/0x20
[23827.498250] ? strscpy+0xa0/0x2a0
[23827.498889] process_one_work+0x8ac/0x14e0
[23827.499638] ? lockdep_hardirqs_on_prepare+0x400/0x400
[23827.500537] ? pwq_dec_nr_in_flight+0x2c0/0x2c0
[23827.501359] ? rwlock_bug.part.0+0x90/0x90
[23827.502116] worker_thread+0x53b/0x1220
[23827.502831] ? process_one_work+0x14e0/0x14e0
[23827.503627] kthread+0x328/0x3f0
[23827.504254] ? _raw_spin_unlock_irq+0x24/0x40
[23827.505065] ? __kthread_bind_mask+0x90/0x90
[23827.505912] ret_from_fork+0x1f/0x30
[23827.506621]
[23827.506987] Allocated by task 28248:
[23827.507694] kasan_save_stack+0x1b/0x40
[23827.508476] __kasan_kmalloc+0x7c/0x90
[23827.509197] mlx5e_attach_encap+0xde1/0x1d40 [mlx5_core]
[23827.510194] mlx5e_tc_add_fdb_flow+0x397/0xc40 [mlx5_core]
[23827.511218] __mlx5e_add_fdb_flow+0x519/0xb30 [mlx5_core]
[23827.512234] mlx5e_configure_flower+0x191c/0x4870 [mlx5_core]
[23827.513298] tc_setup_cb_add+0x1d5/0x420
[23827.514023] fl_hw_replace_filter+0x382/0x6a0 [cls_flower]
[23827.514975] fl_change+0x2ceb/0x4a51 [cls_flower]
[23827.515821] tc_new_tfilter+0x89a/0x2070
[23827.516548] rtnetlink_rcv_msg+0x644/0x8c0
[23827.517300] netlink_rcv_skb+0x11d/0x340
[23827.518021] netlink_unicast+0x42b/0x700
[23827.518742] netlink_sendmsg+0x743/0xc20
[23827.519467] sock_sendmsg+0xb2/0xe0
[23827.520131] ____sys_sendmsg+0x590/0x770
[23827.520851] ___sys_sendmsg+0xd8/0x160
[23827.521552] __sys_sendmsg+0xb7/0x140
[23827.522238] do_syscall_64+0x3a/0x70
[23827.522907] entry_SYSCALL_64_after_hwframe+0x44/0xae
[23827.523797]
[23827.524163] Freed by task 25948:
[23827.524780] kasan_save_stack+0x1b/0x40
[23827.525488] kasan_set_track+0x1c/0x30
[23827.526187] kasan_set_free_info+0x20/0x30
[23827.526968] __kasan_slab_free+0xed/0x130
[23827.527709] slab_free_freelist_hook+0xcf/0x1d0
[23827.528528] kmem_cache_free_bulk+0x33a/0x6e0
[23827.529317] kfree_rcu_work+0x55f/0xb70
[23827.530024] process_one_work+0x8ac/0x14e0
[23827.530770] worker_thread+0x53b/0x1220
[23827.531480] kthread+0x328/0x3f0
[23827.532114] ret_from_fork+0x1f/0x30
[23827.532785]
[23827.533147] Last potentially related work creation:
[23827.534007] kasan_save_stack+0x1b/0x40
[23827.534710] kasan_record_aux_stack+0xab/0xc0
[23827.535492] kvfree_call_rcu+0x31/0x7b0
[23827.536206] mlx5e_tc_del_fdb_flow+0x577/0xef0 [mlx5_core]
[23827.537305] mlx5e_flow_put+0x49/0x80 [mlx5_core]
[23827.538290] mlx5e_delete_flower+0x6d1/0xe60 [mlx5_core]
[23827.539300] tc_setup_cb_destroy+0x18e/0x2f0
[23827.540144] fl_hw_destroy_filter+0x1d2/0x310 [cls_flower]
[23827.541148] __fl_delete+0x4dc/0x660 [cls_flower]
[23827.541985] fl_delete+0x97/0x160 [cls_flower]
[23827.542782] tc_del_tfilter+0x7ab/0x13d0
[23827.543503] rtnetlink_rcv_msg+0x644/0x8c0
[23827.544257] netlink_rcv_skb+0x11d/0x340
[23827.544981] netlink_unicast+0x42b/0x700
[23827.545700] netlink_sendmsg+0x743/0xc20
[23827.546424] sock_sendmsg+0xb2/0xe0
[23827.547084] ____sys_sendmsg+0x590/0x770
[23827.547850] ___sys_sendmsg+0xd8/0x160
[23827.548606] __sys_sendmsg+0xb7/0x140
[23827.549303] do_syscall_64+0x3a/0x70
[23827.549969] entry_SYSCALL_64_after_hwframe+0x44/0xae
[23827.550853]
[23827.551217] The buggy address belongs to the object at ffff8881d1322200
[23827.551217] which belongs to the cache kmalloc-256 of size 256
[23827.553341] The buggy address is located 140 bytes inside of
[23827.553341] 256-byte region [ffff8881d1322200, ffff8881d1322300)
[23827.555747] The buggy address belongs to the page:
[23827.556847] page:00000000898762aa refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1d1320
[23827.558651] head:00000000898762aa order:2 compound_mapcount:0 compound_pincount:0
[23827.559961] flags: 0x2ffff800010200(slab|head|node=0|zone=2|lastcpupid=0x1ffff)
[23827.561243] raw: 002ffff800010200dead000000000100dead000000000122ffff888100042b40
[23827.562653] raw: 0000000000000000000000000020002000000001ffffffff0000000000000000
[23827.564112] page dumped because: kasan: bad access detected
[23827.565439]
[23827.565932] Memory state around the buggy address:
[23827.566917] ffff8881d1322180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[23827.568485] ffff8881d1322200: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[23827.569818] >ffff8881d1322280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[23827.571143] ^
[23827.571879] ffff8881d1322300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[23827.573283] ffff8881d1322380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[23827.574654] ==================================================================
Most of the necessary logic is already correctly implemented by
mlx5e_get_next_valid_encap() helper that is used in neigh stats update
handler. Make the handler generic by renaming it to
mlx5e_get_next_matching_encap() and use callback to test whether flow is
matching instead of hardcoded check for 'valid' flag value. Implement
mlx5e_get_next_valid_encap() by calling mlx5e_get_next_matching_encap()
with callback that tests encap MLX5_ENCAP_ENTRY_VALID flag. Implement new
mlx5e_get_next_init_encap() helper by calling
mlx5e_get_next_matching_encap() with callback that tests encap completion
result to be non-error and use it in mlx5e_rep_neigh_update() to safely
iterate over nhe->encap_list.
Remove encap completion logic from mlx5e_rep_update_flows() since the encap
entries passed to this function are already guaranteed to be properly
initialized by similar code in mlx5e_get_next_init_encap().
Yang Li [Fri, 4 Jun 2021 10:08:27 +0000 (18:08 +0800)]
net/mlx5e: Fix an error code in mlx5e_arfs_create_tables()
When the code execute 'if (!priv->fs.arfs->wq)', the value of err is 0.
So, we use -ENOMEM to indicate that the function
create_singlethread_workqueue() return NULL.
David S. Miller [Wed, 9 Jun 2021 22:45:16 +0000 (15:45 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-06-09
This series contains updates to ice driver only.
Maciej informs the user when XDP is not supported due to the driver
being in the 'safe mode' state. He also adds a parameter to Tx queue
configuration to resolve an issue in configuring XDP queues as it cannot
rely on using the number Tx or Rx queues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This this the counterpart of 8aa7b526dc0b ("openvswitch: handle DNAT
tuple collision") for act_ct. From that commit changelog:
"""
With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.
...
Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.
"""
Fixes: 95219afbb980 ("act_ct: support asymmetric conntrack") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 9 Jun 2021 11:17:53 +0000 (14:17 +0300)]
rtnetlink: Fix regression in bridge VLAN configuration
Cited commit started returning errors when notification info is not
filled by the bridge driver, resulting in the following regression:
# ip link add name br1 type bridge vlan_filtering 1
# bridge vlan add dev br1 vid 555 self pvid untagged
RTNETLINK answers: Invalid argument
As long as the bridge driver does not fill notification info for the
bridge device itself, an empty notification should not be considered as
an error. This is explained in commit 59ccaaaa49b5 ("bridge: dont send
notification when skb->len == 0 in rtnl_bridge_notify").
Fix by removing the error and add a comment to avoid future bugs.
Fixes: a8db57c1d285 ("rtnetlink: Fix missing error code in rtnl_bridge_notify()") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Jun 2021 21:46:21 +0000 (14:46 -0700)]
Merge tag 'mac80211-for-net-2021-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
A fair number of fixes:
* fix more fallout from RTNL locking changes
* fixes for some of the bugs found by syzbot
* drop multicast fragments in mac80211 to align
with the spec and what drivers are doing now
* fix NULL-ptr deref in radiotap injection
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 9 Jun 2021 09:49:01 +0000 (11:49 +0200)]
udp: fix race between close() and udp_abort()
Kaustubh reported and diagnosed a panic in udp_lib_lookup().
The root cause is udp_abort() racing with close(). Both
racing functions acquire the socket lock, but udp{v6}_destroy_sock()
release it before performing destructive actions.
We can't easily extend the socket lock scope to avoid the race,
instead use the SOCK_DEAD flag to prevent udp_abort from doing
any action when the critical race happens.
Diagnosed-and-tested-by: Kaustubh Pandey <kapandey@codeaurora.org> Fixes: 5d77dca82839 ("net: diag: support SOCK_DESTROY for UDP sockets") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Jun 2021 07:59:45 +0000 (00:59 -0700)]
inet: annotate data race in inet_send_prepare() and inet_dgram_connect()
Both functions are known to be racy when reading inet_num
as we do not want to grab locks for the common case the socket
has been bound already. The race is resolved in inet_autobind()
by reading again inet_num under the socket lock.
syzbot reported:
BUG: KCSAN: data-race in inet_send_prepare / udp_lib_get_port
write to 0xffff88812cba150e of 2 bytes by task 24135 on cpu 0:
udp_lib_get_port+0x4b2/0xe20 net/ipv4/udp.c:308
udp_v6_get_port+0x5e/0x70 net/ipv6/udp.c:89
inet_autobind net/ipv4/af_inet.c:183 [inline]
inet_send_prepare+0xd0/0x210 net/ipv4/af_inet.c:807
inet6_sendmsg+0x29/0x80 net/ipv6/af_inet6.c:639
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88812cba150e of 2 bytes by task 24132 on cpu 1:
inet_send_prepare+0x21/0x210 net/ipv4/af_inet.c:806
inet6_sendmsg+0x29/0x80 net/ipv6/af_inet6.c:639
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000 -> 0x9db4
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24132 Comm: syz-executor.2 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Austin Kim [Wed, 9 Jun 2021 02:34:25 +0000 (03:34 +0100)]
net: ethtool: clear heap allocations for ethtool function
Several ethtool functions leave heap uncleared (potentially) by
drivers. This will leave the unused portion of heap unchanged and
might copy the full contents back to userspace.
Signed-off-by: Austin Kim <austindh.kim@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ice: parameterize functions responsible for Tx ring management
Commit ae15e0ba1b33 ("ice: Change number of XDP Tx queues to match
number of Rx queues") tried to address the incorrect setting of XDP
queue count that was based on the Tx queue count, whereas in theory we
should provide the XDP queue per Rx queue. However, the routines that
setup and destroy the set of Tx resources are still based on the
vsi->num_txq.
Ice supports the asynchronous Tx/Rx queue count, so for a setup where
vsi->num_txq > vsi->num_rxq, ice_vsi_stop_tx_rings and ice_vsi_cfg_txqs
will be accessing the vsi->xdp_rings out of the bounds.
Parameterize two mentioned functions so they get the size of Tx resources
array as the input.
Fixes: ae15e0ba1b33 ("ice: Change number of XDP Tx queues to match number of Rx queues") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice: add ndo_bpf callback for safe mode netdev ops
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Fixes: efc2214b6047 ("ice: Add support for XDP") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
projects / mirror_ubuntu-kernels.git / log