Simon Horman [Tue, 24 Mar 2015 00:31:40 +0000 (09:31 +0900)]
rocker: handle non-bridge master change
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.
Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.
This patch makes provision for doing nothing in such cases.
Fixes: 6c7079450071f ("rocker: implement L2 bridge offloading") Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: e7ed828f10bd8 ("netlink: support setting devgroup parameters") Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 23 Mar 2015 14:14:00 +0000 (15:14 +0100)]
tcp: prevent fetching dst twice in early demux code
On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux()
struct dst_entry *dst = sk->sk_rx_dst;
if (dst)
dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);
to code reading sk->sk_rx_dst twice, once for the test and once for
the argument of ip6_dst_check() (dst_check() is inline). This allows
ip6_dst_check() to be called with null first argument, causing a crash.
Protect sk->sk_rx_dst access by READ_ONCE() both in IPv4 and IPv6
TCP early demux code.
Fixes: 41063e9dd119 ("ipv4: Early TCP socket demux.") Fixes: c7109986db3c ("ipv6: Early TCP socket demux") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 23 Mar 2015 08:56:14 +0000 (10:56 +0200)]
bnx2x: Fix statistics locking scheme
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2015 02:36:37 +0000 (22:36 -0400)]
Merge tag 'linux-can-fixes-for-4.0-20150322' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-22
this is a pull-request of 7 patches for net/master.
Ahmed S. Darwish fixes another two problems in the kvaser_usb driver. A patch
by Colin Ian King for the gs_usb driver adds a missing check for kzalloc
allocation failures. Two patches by Stephane Grosjean for the peak_usb driver
add missing support for ISO / non-ISO mode switching. Andri Yngvason
contributes a patch to fix the state handling in the flexcan driver. The last
patch by Andreas Werner for the flexcan driver add missing EPROBE_DEFER
handling for the transceiver regulator.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Validate iov ranges before feeding them into iov_iter_init(), from
Al Viro.
2) We changed copy_from_msghdr_from_user() to zero out the msg_namelen
is a NULL pointer is given for the msg_name. Do the same in the
compat code too. From Catalin Marinas.
3) Fix partially initialized tuples in netfilter conntrack helper, from
Ian Wilson.
4) Missing continue; statement in nft_hash walker can lead to crashes,
from Herbert Xu.
5) tproxy_tg6_check looks for IP6T_INV_PROTO in ->flags instead of
->invflags, fix from Pablo Neira Ayuso.
6) Incorrect memory account of TCP FINs can result in negative socket
memory accounting values. Fix from Josh Hunt.
7) Don't allow virtual functions to enable VLAN promiscuous mode in
be2net driver, from Vasundhara Volam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: nft_compat: set IP6T_F_PROTO flag if protocol is set
cx82310_eth: wait for firmware to become ready
net: validate the range we feed to iov_iter_init() in sys_sendto/sys_recvfrom
net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
be2net: use PCI MMIO read instead of config read for errors
be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs
be2net: Prevent VFs from enabling VLAN promiscuous mode
tcp: fix tcp fin memory accounting
ipv6: fix backtracking for throw routes
net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}
ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in udp6_ufo_fragment
netfilter: xt_TPROXY: fix invflags check in tproxy_tg6_check()
netfilter: restore rule tracing via nfnetlink_log
netfilter: nf_tables: allow to change chain policy without hook if it exists
netfilter: Fix potential crash in nft_hash walker
netfilter: Zero the tuple in nfnl_cthelper_parse_tuple()
David S. Miller [Mon, 23 Mar 2015 16:22:10 +0000 (09:22 -0700)]
sparc64: Fix several bugs in memmove().
Firstly, handle zero length calls properly. Believe it or not there
are a few of these happening during early boot.
Next, we can't just drop to a memcpy() call in the forward copy case
where dst <= src. The reason is that the cache initializing stores
used in the Niagara memcpy() implementations can end up clearing out
cache lines before we've sourced their original contents completely.
For example, considering NG4memcpy, the main unrolled loop begins like
this:
Assume dst is 64 byte aligned and let's say that dst is src - 8 for
this memcpy() call. That store at the end there is the one to the
first line in the cache line, thus clearing the whole line, which thus
clobbers "src + 0x28" before it even gets loaded.
To avoid this, just fall through to a simple copy only mildly
optimized for the case where src and dst are 8 byte aligned and the
length is a multiple of 8 as well. We could get fancy and call
GENmemcpy() but this is good enough for how this thing is actually
used.
Reported-by: David Ahern <david.ahern@oracle.com> Reported-by: Bob Picco <bpicco@meloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix missing initialization of tuple structure in nfnetlink_cthelper
to avoid mismatches when looking up to attach userspace helpers to
flows, from Ian Wilson.
2) Fix potential crash in nft_hash when we hit -EAGAIN in
nft_hash_walk(), from Herbert Xu.
3) We don't need to indicate the hook information to update the
basechain default policy in nf_tables.
4) Restore tracing over nfnetlink_log due to recent rework to
accomodate logging infrastructure into nf_tables.
5) Fix wrong IP6T_INV_PROTO check in xt_TPROXY.
6) Set IP6T_F_PROTO flag in nft_compat so we can use SYNPROXY6 and
REJECT6 from xt over nftables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 22 Mar 2015 19:07:47 +0000 (12:07 -0700)]
Merge tag 'driver-core-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two bugfixes for things reported. One regression in kernfs,
and another issue fixed in the LZ4 code that was fixed in the
"upstream" codebase that solves a reported kernel crash
Both have been in linux-next for a while"
* tag 'driver-core-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
LZ4 : fix the data abort issue
kernfs: handle poll correctly on 'direct_read' files.
Linus Torvalds [Sun, 22 Mar 2015 19:03:14 +0000 (12:03 -0700)]
Merge tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
were merged in 4.0-rc1 that cause regressions. So let's revert them
for now and they will be reworked and resent sometime in the future.
All have been tested in linux-next for a while"
* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "pcmcia: add a new resource manager for non ISA systems"
Revert "pcmcia: fix incorrect bracketing on a test"
Revert "pcmcia: add missing include for new pci resource handler"
Linus Torvalds [Sun, 22 Mar 2015 18:59:02 +0000 (11:59 -0700)]
Merge tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are four small staging driver fixes, all for the vt6656 and
vt6655 drivers, that resolve some reported issues with them.
All of these patches have been in linux next for a while"
* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
vt6655: Fix late setting of byRFType.
vt6655: RFbSetPower fix missing rate RATE_12M
staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
staging: vt6655: vnt_tx_packet fix dma_idx selection.
Linus Torvalds [Sun, 22 Mar 2015 18:54:29 +0000 (11:54 -0700)]
Merge tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fix from Greg KH:
"Here's a single 8250 serial driver that fixes a reported deadlock with
the serial console and the tty driver.
It's been in linux-next for a while now"
* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Fix deadlock in LCR workaround
Linus Torvalds [Sun, 22 Mar 2015 18:33:55 +0000 (11:33 -0700)]
Merge tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here's a number of USB and PHY driver fixes for 4.0-rc5.
The largest thing here is a revert of a gadget function driver patch
that removes 500 lines of code. Other than that, it's a number of
reported bugs fixes and new quirk/id entries.
All have been in linux-next for a while"
* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: common: otg-fsm: only signal connect after switching to peripheral
uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
USB: ehci-atmel: rework clk handling
MAINTAINERS: add entry for USB OTG FSM
usb: chipidea: otg: add a_alt_hnp_support response for B device
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
phy: ti/omap: Fix modalias
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
phy: Find the right match in devm_phy_destroy()
phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
phy: samsung-usb2: Remove NULL terminating entry from phys array
phy: hix5hd2-sata: Check return value of platform_get_resource
phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
Revert "usb: gadget: zero: Add support for interrupt EP"
Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
...
Andreas Werner [Sun, 22 Mar 2015 16:35:52 +0000 (17:35 +0100)]
can: flexcan: Deferred on Regulator return EPROBE_DEFER
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: peak_usb_fd: add support for ISO / non-ISO mode switching
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ahmed S. Darwish [Sun, 15 Mar 2015 15:10:49 +0000 (11:10 -0400)]
can: kvaser_usb: Fix sparse warning __le16 degrades to integer
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ahmed S. Darwish [Sun, 15 Mar 2015 15:03:38 +0000 (11:03 -0400)]
can: kvaser_usb: Comply with firmware max tx URBs value
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ondrej Zary [Sat, 21 Mar 2015 10:29:37 +0000 (11:29 +0100)]
cx82310_eth: wait for firmware to become ready
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 21 Mar 2015 20:05:37 +0000 (13:05 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave dmaengine fixes from Vinod Koul:
"Four fixes for dw, pl08x, imx-sdma and at_hdmac driver. Nothing
unusual here, simple fixes to these drivers"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pl08x: Define capabilities for generic capabilities reporting
dmaengine: dw: append MODULE_ALIAS for platform driver
dmaengine: imx-sdma: switch to dynamic context mode after script loaded
dmaengine: at_hdmac: Fix calculation of the residual bytes
Linus Torvalds [Sat, 21 Mar 2015 19:51:36 +0000 (12:51 -0700)]
Merge tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (PCI/ACPI resources and at91
RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
cpuidle fixes (one stable-candidate too).
Specifics:
- Revert a recent PCI commit related to IRQ resources management that
introduced a regression for drivers attempting to bind to devices
whose previous drivers did not balance pci_enable_device() and
pci_disable_device() as expected (Rafael J Wysocki).
- Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
recent commit related to wakeup interrupt handling (Dan Carpenter).
- Allow the power capping RAPL (Running-Average Power Limit) driver
to use different energy units for domains within one CPU package
which is necessary to handle Intel Haswell EP processors correctly
(Jacob Pan).
- Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
updating the target residency and exit latency numbers for those
chips (Sebastien Rannou).
- Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
in a row before cpu_pm_exit() is called on the same CPU which
breaks the core's assumptions regarding the usage of those
functions (Gregory Clement)"
* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
powercap / RAPL: handle domains with different energy units
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
Linus Torvalds [Sat, 21 Mar 2015 19:41:50 +0000 (12:41 -0700)]
Merge git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"A bunch of fixes across drivers:
radeon:
disable two ended allocation for now, it breaks some stuff
amdkfd:
misc fixes
nouveau:
fix irq loop problem, add basic support for GM206 (new hw)
i915:
fix some WARNs people were seeing
exynos:
fix some iommu interactions causing boot failures"
* git://people.freedesktop.org/~airlied/linux:
drm/radeon: drop ttm two ended allocation
drm/exynos: fix the initialization order in FIMD
drm/exynos: fix typo config name correctly.
drm/exynos: Check for NULL dereference of crtc
drm/exynos: IS_ERR() vs NULL bug
drm/exynos: remove unused files
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
Linus Torvalds [Sat, 21 Mar 2015 19:33:01 +0000 (12:33 -0700)]
Merge tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more DeviceTree fixes vfom Rob Herring:
- revert setting stdout-path as preferred console. This caused
regressions in PowerMACs and other systems.
- yet another fix for stdout-path option parsing.
- fix error path handling in of_irq_parse_one
* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Revert "of: Fix premature bootconsole disable with 'stdout-path'"
of: handle both '/' and ':' in path strings
of: unittest: Add option string test case with longer path
of/irq: Fix of_irq_parse_one() returned error codes
Pull SCSI target fixes from Nicholas Bellinger:
"Here are current target-pending fixes for v4.0-rc5 code that have made
their way into the queue over the last weeks.
The fixes this round include:
- Fix long-standing iser-target logout bug related to early
conn_logout_comp completion, resulting in iscsi_conn use-after-tree
OOpsen. (Sagi + nab)
- Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
handing for DDP hw offload. (DanC)
- Fix incorrect use of unprotected __transport_register_session() in
tcm_qla2xxx + other single local se_node_acl fabrics. (Bart)
- Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
for ack_kref=1 failure path. (Bart)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
target: Fix virtual LUN=0 target_configure_device failure OOPs
target/pscsi: Fix NULL pointer dereference in get_device_type
tcm_fc: missing curly braces in ft_invl_hw_context()
target: Fix reference leak in target_get_sess_cmd() error path
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
tcm_qla2xxx: Fix incorrect use of __transport_register_session
iscsi-target: Avoid early conn_logout_comp for iser connections
Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
target: Disallow changing of WRITE cache/FUA attrs after export
Linus Torvalds [Sat, 21 Mar 2015 18:15:13 +0000 (11:15 -0700)]
Merge tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull devicemapper fixes from Mike Snitzer:
"A handful of stable fixes for DM:
- fix thin target to always zero-fill reads to unprovisioned blocks
- fix to interlock device destruction's suspend from internal
suspends
- fix 2 snapshot exception store handover bugs
- fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing"
* tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME
dm snapshot: suspend merging snapshot when doing exception handover
dm snapshot: suspend origin when doing exception handover
dm: hold suspend_lock while suspending device during device deletion
dm thin: fix to consistently zero-fill reads to unprovisioned blocks
Linus Torvalds [Sat, 21 Mar 2015 17:53:37 +0000 (10:53 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Most of these are fixing extent reservation accounting, or corners
with tree writeback during commit.
Josef's set does add a test, which isn't strictly a fix, but it'll
keep us from making this same mistake again"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix outstanding_extents accounting in DIO
Btrfs: add sanity test for outstanding_extents accounting
Btrfs: just free dummy extent buffers
Btrfs: account merges/splits properly
Btrfs: prepare block group cache before writing
Btrfs: fix ASSERT(list_empty(&cur_trans->dirty_bgs_list)
Btrfs: account for the correct number of extents for delalloc reservations
Btrfs: fix merge delalloc logic
Btrfs: fix comp_oper to get right order
Btrfs: catch transaction abortion after waiting for it
btrfs: fix sizeof format specifier in btrfs_check_super_valid()
Linus Torvalds [Sat, 21 Mar 2015 17:24:10 +0000 (10:24 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- mm switching fix where the kernel pgd ends up in the user TTBR0 after
returning from an EFI run-time services call
- fix __GFP_ZERO handling for atomic pool and CMA DMA allocations (the
generic code does get the gfp flags, so it's left with the arch code
to memzero accordingly)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Honor __GFP_ZERO in dma allocations
arm64: efi: don't restore TTBR0 if active_mm points at init_mm
Linus Torvalds [Sat, 21 Mar 2015 17:03:22 +0000 (10:03 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another few ARM fixes. Fabrice fixed the L2 cache DT parsing to allow
prefetch configuration to be specified even when the cache size
parsing fails.
Laura noticed that the setting of page attributes wasn't working for
modules due to is_module_addr() always returning false.
Marc Gonzalez (aka Mason) noticed a potential latent bug with the way
we read one of the CPUID registers (where we could attempt to read a
non-present CPUID register which may fault.)
I've fixed an issue where 32-bit DMA masks were failing with memory
which extended to the top of physical address space, and I've also
added debugging output of the page tables when we hit a data access
exception which we don't specifically handle - prompted by the lack of
information in a bug report"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8313/1: Use read_cpuid_ext() macro instead of inline asm
ARM: 8311/1: Don't use is_module_addr in setting page attributes
ARM: 8310/1: l2c: Fix prefetch settings dt parsing
ARM: dump pgd, pmd and pte states on unhandled data abort faults
ARM: dma-api: fix off-by-one error in __dma_supported()
NeilBrown [Fri, 13 Mar 2015 00:51:18 +0000 (11:51 +1100)]
md: fix problems with freeing private data after ->run failure.
If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.
However:
md.c calls ->free() even if ->private_data is NULL, which
causes problems in some personalities.
raid0.c frees the data, but doesn't clear ->private_data,
which will become a problem when we fix md.c
So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com> Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381 Signed-off-by: NeilBrown <neilb@suse.de>
Catalin Marinas [Fri, 20 Mar 2015 16:48:13 +0000 (16:48 +0000)]
net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
Commit db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an
error) introduced the clamping of msg_namelen when the unsigned value
was larger than sizeof(struct sockaddr_storage). This caused a
msg_namelen of -1 to be valid. The native code was subsequently fixed by
commit dbb490b96584 (net: socket: error on a negative msg_namelen).
In addition, the native code sets msg_namelen to 0 when msg_name is
NULL. This was done in commit (6a2a2b3ae075 net:socket: set msg_namelen
to 0 if msg_name is passed as NULL in msghdr struct from userland) and
subsequently updated by 08adb7dabd48 (fold verify_iovec() into
copy_msghdr_from_user()).
This patch brings the get_compat_msghdr() in line with
copy_msghdr_from_user().
Fixes: db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error) Cc: David S. Miller <davem@davemloft.net> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Mar 2015 17:25:56 +0000 (13:25 -0400)]
Merge branch 'be2net'
Sathya Perla says:
====================
be2net: patch set
Hi David, this patch set includes 3 bug fixes to the be2net driver.
Patch 1 fixes a vlan isolation issue with VFs. When a VF is placed in
promiscous mode, it could receive packets belonging to any vlan, as
the PF driver grants vlan promisc capability to VFs. The PF
driver now disables the vlan promisc capability for VFs to fix this
problem.
Patch 2 fixes the call to MODIFY_EQ_DELAY FW cmd to not include more
than 8 EQs per cmd. The FW is not capable of handling more than 8 EQs
per cmd.
Patch 3 fixes an EEH error detection issue. On Power platforms,
when an EEH error occurs, the slot disconnect state is more reliably
detected via an MMIO read compared to a config read. So, the error
register reads that occur every second are now done via MMIO.
Pls apply this patch set to the "net" tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Fri, 20 Mar 2015 10:28:25 +0000 (06:28 -0400)]
be2net: use PCI MMIO read instead of config read for errors
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Fri, 20 Mar 2015 10:28:24 +0000 (06:28 -0400)]
be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time. Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 20 Mar 2015 10:28:23 +0000 (06:28 -0400)]
be2net: Prevent VFs from enabling VLAN promiscuous mode
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr> Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Hunt [Thu, 19 Mar 2015 23:19:30 +0000 (19:19 -0400)]
tcp: fix tcp fin memory accounting
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0) Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Thu, 19 Mar 2015 15:43:00 +0000 (15:43 +0000)]
arm64: efi: don't restore TTBR0 if active_mm points at init_mm
init_mm isn't a normal mm: it has swapper_pg_dir as its pgd (which
contains kernel mappings) and is used as the active_mm for the idle
thread.
When restoring the pgd after an EFI call, we write current->active_mm
into TTBR0. If the current task is actually the idle thread (e.g. when
initialising the EFI RTC before entering userspace), then the TLB can
erroneously populate itself with junk global entries as a result of
speculative table walks.
When we do eventually return to userspace, the task can end up hitting
these junk mappings leading to lockups, corruption or crashes.
This patch fixes the problem in the same way as the CPU suspend code by
ensuring that we never switch to the init_mm in efi_set_pgd and instead
point TTBR0 at the zero page. A check is also added to cpu_switch_mm to
BUG if we get passed swapper_pg_dir.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Fixes: f3cdfd239da5 ("arm64/efi: move SetVirtualAddressMap() to UEFI stub") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Steven Barth [Thu, 19 Mar 2015 15:16:04 +0000 (16:16 +0100)]
ipv6: fix backtracking for throw routes
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Markos Chandras [Thu, 19 Mar 2015 10:28:14 +0000 (10:28 +0000)]
net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org> Cc: <stable@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: Don Fry <pcnet32@frontier.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 19 Mar 2015 10:22:32 +0000 (11:22 +0100)]
ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in udp6_ufo_fragment
Matt Grant reported frequent crashes in ipv6_select_ident when
udp6_ufo_fragment is called from openvswitch on a skb that doesn't
have a dst_entry set.
ipv6_proxy_select_ident generates the frag_id without using the dst
associated with the skb. This approach was suggested by Vladislav
Yasevich.
Fixes: 0508c07f5e0c ("ipv6: Select fragment id during UFO segmentation if not set.") Cc: Vladislav Yasevich <vyasevic@redhat.com> Reported-by: Matt Grant <matt@mattgrant.net.nz> Tested-by: Matt Grant <matt@mattgrant.net.nz> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
Commit b4b55cda5874 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda5874 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dave Airlie [Fri, 20 Mar 2015 07:32:21 +0000 (17:32 +1000)]
Merge tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Backporting a couple of plane related fixes from drm-next to v4.0.
* tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
Dave Airlie [Fri, 20 Mar 2015 07:32:01 +0000 (17:32 +1000)]
Merge tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Fixing SDMA initialization when in non-HWS mode (debug mode)
- Memory leak fix when destroying kernel queue
- Fix number of available compute pipelines according to new firmware
* tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux:
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com> Cc: Claudio Fleiner <cmf@daterainc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> # v3.7+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target/pscsi: Fix NULL pointer dereference in get_device_type
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dan Carpenter [Wed, 25 Feb 2015 13:21:03 +0000 (16:21 +0300)]
tcm_fc: missing curly braces in ft_invl_hw_context()
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
Bart Van Assche [Thu, 12 Feb 2015 10:48:49 +0000 (11:48 +0100)]
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Bart Van Assche [Fri, 20 Mar 2015 05:25:16 +0000 (22:25 -0700)]
tcm_qla2xxx: Fix incorrect use of __transport_register_session
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
iscsi-target: Avoid early conn_logout_comp for iser connections
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
target: Disallow changing of WRITE cache/FUA attrs after export
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: James Bottomley <JBottomley@Parallels.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
David Ahern [Thu, 19 Mar 2015 20:06:53 +0000 (16:06 -0400)]
sparc: Touch NMI watchdog when walking cpus and calling printk
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 19 Mar 2015 20:06:37 +0000 (16:06 -0400)]
sparc: perf: Add support M7 processor
The M7 processor has a different hypervisor group id and different PCR fast
trap values. PIC read/write functions and PCR bit fields are the same as
the T4 so those are reused.
Signed-off-by: David Ahern <david.ahern@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
perf_pmu_disable is called by core perf code before pmu->del and the
enable function is called by core perf code afterwards. No need to
call again within sparc_pmu_del.
Ditto for pmu->add and sparc_pmu_add.
Signed-off-by: David Ahern <david.ahern@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 19 Mar 2015 23:43:10 +0000 (16:43 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"An update to Synaptics driver that makes it usable with the 2015
lineup from Lenovo"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
Input: synaptics - remove X250 from the topbuttonpad list
Input: synaptics - remove X1 Carbon 3rd gen from the topbuttonpad list
Input: synaptics - re-route tracksticks buttons on the Lenovo 2015 series
Input: synaptics - remove TOPBUTTONPAD property for Lenovos 2015
Input: synaptics - retrieve the extended capabilities in query $10
Input: synaptics - do not retrieve the board id on old firmwares
Input: synaptics - handle spurious release of trackstick buttons
Input: synaptics - fix middle button on Lenovo 2015 products
Input: synaptics - skip quirks when post-2013 dimensions
Input: synaptics - support min/max board id in min_max_pnpid_table
Input: synaptics - remove obsolete min/max quirk for X240
Input: synaptics - query min dimensions for fw v8.1
Input: synaptics - log queried and quirked dimension values
Input: synaptics - split synaptics_resolution(), query first
Linus Torvalds [Thu, 19 Mar 2015 23:27:36 +0000 (16:27 -0700)]
Merge branch 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This fixes minor issues with the multi-layer update in v4.0"
* 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: upper fs should not be R/O
ovl: check lowerdir amount for non-upper mount
ovl: print error message for invalid mount options
Linus Torvalds [Thu, 19 Mar 2015 22:52:28 +0000 (15:52 -0700)]
Merge tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a slew of pin control fixes I've accumulated for the v4.0
kernel. Nothing special, just driver fixes (mainly embedded Intel it
seems) and a misunderstanding regarding the stub functions was
reverted:
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and sleep context
save in the Baytrail driver.
- Make default output directions work properly in the Cherryview
driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in the sunxi
driver"
* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
pinctrl: at91: move lock/unlock_as_irq calls into request/release
pinctrl: update direction_output function of cherryview driver
pinctrl: baytrail: Save pin context over system sleep
pinctrl: baytrail: Rework interrupt handling
pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
pinctrl: baytrail: Relax GPIO request rules
Revert "pinctrl: consumer: use correct retval for placeholder functions"
Linus Torvalds [Thu, 19 Mar 2015 22:24:28 +0000 (15:24 -0700)]
Merge tag 'nios2-fixes-v4.0-rc5' of git://git.rocketboards.org/linux-socfpga-next
Pull two arch/nios2 fixes from Ley Foon Tan:
- Remove ucontext.h from exported arch headers
- nios2: mm: do not invoke OOM killer on kernel fault OOM
* tag 'nios2-fixes-v4.0-rc5' of git://git.rocketboards.org/linux-socfpga-next:
nios2: mm: do not invoke OOM killer on kernel fault OOM
nios2: Remove ucontext.h from exported arch headers
Due to a merge error when creating c5c707f9 ("nfsd: implement pNFS
layout recalls"), we recursively call nfsd4_cb_layout_fail from itself,
leading to stack overflows.
Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: c5c707f9 ("nfsd: implement pNFS layout recalls") Signed-off-by: J. Bruce Fields <bfields@redhat.com>
---
fs/nfsd/nfs4layouts.c | 2 --
1 file changed, 2 deletions(-)
1) Fix packet header offset calculation in _decode_session6(), from
Hajime Tazaki.
2) Fix route leak in error paths of xfrm_lookup(), from Huaibin Wang.
3) Be sure to clear state properly when scans fail in iwlwifi mvm code,
from Luciano Coelho.
4) iwlwifi tries to stop scans that aren't actually running, also from
Luciano Coelho.
5) mac80211 should drop mesh frames that are not encrypted, fix from
Bob Copeland.
6) Add new device ID to b43 wireless driver for BCM432228 chips, from
Rafał Miłecki.
7) Fix accidental addition of members after variable sized array in
struct tc_u_hnode, from WANG Cong.
8) Don't re-enable interrupts until after we call napi_complete() in
ibmveth and WIZnet drivers, frm Yongbae Park.
9) Fix regression in vlan tag handling of fec driver, from Fugang Duan.
10) If a network namespace change fails during rtnl_newlink(), we don't
unwind the device registry properly.
11) Fix two TCP regressions, from Neal Cardwell:
- Don't allow snd_cwnd_cnt to accumulate huge values due to missing
test in tcp_cong_avoid_ai().
- Restore CUBIC back to advancing cwnd by 1.5x packets per RTT.
12) Fix performance regression in xne-netback involving push TX
notifications, from David Vrabel.
13) __skb_tstamp_tx() can be called with a NULL sk pointer, do not
dereference blindly. From Willem de Bruijn.
14) Fix potential stack overflow in RDS protocol stack, from Arnd
Bergmann.
15) VXLAN_VID_MASK used incorrectly in new remote checksum offload
support of VXLAN driver. Fix from Alexey Kodanev.
16) Fix too small netlink SKB allocation in inet_diag layer, from Eric
Dumazet.
17) ieee80211_check_combinations() does not count interfaces correctly,
from Andrei Otcheretianski.
18) Hardware feature determination in bxn2x driver references a piece of
software state that actually isn't initialized yet, fix from Michal
Schmidt.
19) inet_csk_wait_for_connect() needs a sched_annotate_sleep()
annoation, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
Revert "net: cx82310_eth: use common match macro"
net/mlx4_en: Set statistics bitmap at port init
IB/mlx4: Saturate RoCE port PMA counters in case of overflow
net/mlx4_en: Fix off-by-one in ethtool statistics display
IB/mlx4: Verify net device validity on port change event
act_bpf: allow non-default TC_ACT opcodes as BPF exec outcome
Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
inet: Clean up inet_csk_wait_for_connect() vs. might_sleep()
ip6_tunnel: fix error code when tunnel exists
netdevice.h: fix ndo_bridge_* comments
bnx2x: fix encapsulation features on 57710/57711
mac80211: ignore CSA to same channel
nl80211: ignore HT/VHT capabilities without QoS/WMM
mac80211: ask for ECSA IE to be considered for beacon parse CRC
mac80211: count interfaces correctly for combination checks
isdn: icn: use strlcpy() when parsing setup options
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
bridge: reset bridge mtu after deleting an interface
can: kvaser_usb: Fix tx queue start/stop race conditions
...
Tom Van Braeckel [Mon, 12 Jan 2015 04:22:16 +0000 (05:22 +0100)]
fuse: explicitly set /dev/fuse file's private_data
The misc subsystem (which is used for /dev/fuse) initializes private_data to
point to the misc device when a driver has registered a custom open file
operation, and initializes it to NULL when a custom open file operation has
*not* been provided.
This subtle quirk is confusing, to the point where kernel code registers
*empty* file open operations to have private_data point to the misc device
structure. And it leads to bugs, where the addition or removal of a custom open
file operation surprisingly changes the initial contents of a file's
private_data structure.
So to simplify things in the misc subsystem, a patch [1] has been proposed to
*always* set the private_data to point to the misc device, instead of only
doing this when a custom open file operation has been registered.
But before this patch can be applied we need to modify drivers that make the
assumption that a misc device file's private_data is initialized to NULL
because they didn't register a custom open file operation, so they don't rely
on this assumption anymore. FUSE uses private_data to store the fuse_conn and
errors out if this is not initialized to NULL at mount time.
Hence, we now set a file's private_data to NULL explicitly, to be independent
of whatever value the misc subsystem initializes it to by default.
[1] https://lkml.org/lkml/2014/12/4/939
Reported-by: Giedrius Statkevicius <giedriuswork@gmail.com> Reported-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The assumption that at least 1 preferred console will be registered
when the stdout-path property is set is invalid, which can result
in _no_ consoles.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Rob Herring <robh@kernel.org>
Brian Norris [Tue, 17 Mar 2015 19:30:31 +0000 (12:30 -0700)]
of: handle both '/' and ':' in path strings
Commit 106937e8ccdc ("of: fix handling of '/' in options for
of_find_node_by_path()") caused a regression in OF handling of
stdout-path. While it fixes some cases which have '/' after the ':', it
breaks cases where there is more than one '/' *before* the ':'.
So rather than doing sequentialized checks (first for '/', then for ':';
or vice versa), to get the correct behavior we need to check for the
first occurrence of either one of them.
It so happens that the handy strcspn() helper can do just that.
Fixes: 106937e8ccdc ("of: fix handling of '/' in options for of_find_node_by_path()") Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: stable@vger.kernel.org # 3.19 Acked-by: Leif Lindholm <leif.lindholm@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
Brian Norris [Tue, 17 Mar 2015 19:30:32 +0000 (12:30 -0700)]
of: unittest: Add option string test case with longer path
There were regressions seen with commit 106937e8ccdc ("of: fix handling
of '/' in options for of_find_node_by_path()"), where we couldn't handle
extra '/' before the ':'. Let's test for this now.
Confirmed that this test fails without the previous patch and passes
when patched. All other tests pass.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Leif Lindholm <leif.lindholm@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
Laurent Pinchart [Tue, 17 Mar 2015 22:21:32 +0000 (00:21 +0200)]
of/irq: Fix of_irq_parse_one() returned error codes
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
NeilBrown [Sat, 21 Feb 2015 04:15:16 +0000 (15:15 +1100)]
mmc: pwrseq_simple: fix error path in mmc_pwrseq_simple_alloc
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Since fab4085 ("netfilter: log: nf_log_packet() as real unified
interface"), the loginfo structure that is passed to nf_log_packet() is
used to explicitly indicate the logger type you want to use.
This is a problem for people tracing rules through nfnetlink_log since
packets are always routed to the NF_LOG_TYPE logger after the
aforementioned patch.
We can fix this by removing the trace loginfo structures, but that still
changes the log level from 4 to 5 for tracing messages and there may be
someone relying on this outthere. So let's just introduce a new
nf_log_trace() function that restores the former behaviour.
Reported-by: Markus Kötter <koetter@rrzn.uni-hannover.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dave Airlie [Thu, 19 Mar 2015 04:01:42 +0000 (14:01 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Some urgent regression fixes to booting failures Exynos DRM occured.
Summary:
- Fix two urgent null pointer dereference bugs in case of enabling
or disabling IOMMU. There was two cases to these issues.
One is that plane->crtc is accessed by exynos_disable_plane()
when device tree binding is broken so device driver tries
to release, which means that the mode set operation isn't invoked yet
so plane->crtc is still NULL and exynos_disable_plane() will access
NULL pointer. This issue is fixed by checking if the plane->crtc
is NULL or not in exynos_disable_plane()
Other is that fimd_wait_for_vblank() is called to avoid from page fault
with IOMMU before the ctx object is created. At this time,
fimd_wait_for_vblank() tries to access ctx->crtc but the ctx->crtc
is still NULL because exynos_drm_crtc_create() isn't called yet.
This issue is fixed by creating a crtc object and setting it to
ctx->crtc prior to fimd_wait_for_vblank() call.
For more details, you can refer to below an e-mail thread,
http://www.spinics.net/lists/linux-samsung-soc/msg42436.html
- Remove unnecessary file not used and fix trivial issues.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix the initialization order in FIMD
drm/exynos: fix typo config name correctly.
drm/exynos: Check for NULL dereference of crtc
drm/exynos: IS_ERR() vs NULL bug
drm/exynos: remove unused files
Use jiffies_to_msecs for converting jiffies as it handles all of the corner
cases reliably and also helps readability. The printk format is fixed up
as jiffies_to_msecs returns unsigned int not unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Mar 2015 02:15:28 +0000 (19:15 -0700)]
sparc: Fix /proc/kcore
/proc/kcore investigates the "System RAM" elements in /proc/iomem to
initialize it's memory tables. Therefore we have to register them
before it tries to do so. kcore uses device_initcall() so let's
use arch_initcall() for the registry.
Also we need ARCH_PROC_KCORE_TEXT to get the virtual addresses of
the kernel image correct.
Reported-by: David Ahern <david.ahern@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Wed, 18 Mar 2015 14:51:38 +0000 (16:51 +0200)]
net/mlx4_en: Set statistics bitmap at port init
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Wed, 18 Mar 2015 14:51:37 +0000 (16:51 +0200)]
IB/mlx4: Saturate RoCE port PMA counters in case of overflow
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349cc7 ('IB/mlx4: Support PMA counters for IBoE') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Wed, 18 Mar 2015 14:51:36 +0000 (16:51 +0200)]
net/mlx4_en: Fix off-by-one in ethtool statistics display
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb04b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Moni Shoua [Wed, 18 Mar 2015 14:51:35 +0000 (16:51 +0200)]
IB/mlx4: Verify net device validity on port change event
Processing an event is done in a different context from the one when
the event was dispatched. This requires a check that the slave
net device is still valid when the event is being processed. The check is done
under the iboe lock which ensure correctness.
Fixes: a57500903093 ('IB/mlx4: Add port aggregation support') Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 18 Mar 2015 18:17:03 +0000 (11:17 -0700)]
Merge tag 'sound-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a collection of many small fixes. Most of fixes are for ASoC
drivers, including the fixes of wrong field usages for boolean kctls.
In addition, there is a fix in ASoC core for adding proper locks for
component lists, and a fix for a HD-audio regression by the previous
mono channel fix"
* tag 'sound-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda - Treat stereo-to-mono mix properly
ASoC: wm9713: Fix wrong value references for boolean kctl
ASoC: wm9712: Fix wrong value references for boolean kctl
ASoC: wm8960: Fix wrong value references for boolean kctl
ASoC: wm8955: Fix wrong value references for boolean kctl
ASoC: wm8904: Fix wrong value references for boolean kctl
ASoC: wm8903: Fix wrong value references for boolean kctl
ASoC: wm8731: Fix wrong value references for boolean kctl
ASoC: wm2000: Fix wrong value references for boolean kctl
ASoC: tas5086: Fix wrong value references for boolean kctl
ASoC: pcm1681: Fix wrong value references for boolean kctl
ASoC: es8238: Fix wrong value references for boolean kctl
ASoC: cs4271: Fix wrong value references for boolean kctl
ASoC: ak4641: Fix wrong value references for boolean kctl
ASoC: adav80x: Fix wrong value references for boolean kctl
ASoC: Fix component lists locking
ASoC: Intel: remove conflicts when load/unload multiple firmware images
ASoC: rt286: Change the DMI mapping for Dino
ASoC: sgtl5000: remove useless register write clearing CHRGPUMP_POWERUP
ASoC: fsl_ssi: Don't try to round-up for PM divisor calculation
...
Pull crypto fixes from Herbert Xu:
"Fix a bug in the ARM XTS implementation that can cause failures in
decrypting encrypted disks, and fix is a memory overwrite bug that can
cause a crash which can be triggered from userspace"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - fix memory usage in GCM decryption
crypto: arm/aes update NEON AES module to latest OpenSSL version
Linus Torvalds [Wed, 18 Mar 2015 17:42:19 +0000 (10:42 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for pen pen proximity / touch events in wacom driver, from Ping
Cheng and Benjamin Tissoires
- two new device-specific quirks from Oliver Neukum and Forest
Wilkinson
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: check for wacom->shared before following the pointer
HID: tivo: enable all buttons on the TiVo Slide Pro remote
HID: add ALWAYS_POLL quirk for a Logitech 0xc007
HID: wacom: rely on actual touch down count to decide touch_down
HID: wacom: do not send pen events before touch is up/forced out
projects / mirror_ubuntu-eoan-kernel.git / log