If a card driver is compiled into the kernel and mt2131 or s5h1409 are
compiled as modules, the kernel won't link.
A compiled in driver can't use a module, so in this case the mt2131 or s5h1409
are effectively disabled w.r.t the compiled in driver and the stub attach
function should be used.
Trent Piepho [Wed, 1 Aug 2007 02:06:50 +0000 (23:06 -0300)]
V4L/DVB (5975): cx88: Wrong values used for HD-3000 radio mode
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Ian Armstrong [Fri, 3 Aug 2007 13:01:39 +0000 (10:01 -0300)]
V4L/DVB (5973): ivtv: attach yuv field order to each frame
In the current driver, the field order is global. As soon as it's changed it
takes immediate effect. This is a problem when the video changes order mid
stream. Although it mostly works okay, the video may judder / flicker.
This patch attaches the field order to the frame, so that any buffered frames
will not be displayed until the correct field. In the event that the field
order is changed mid stream, the driver will ensure that the previous frame
is displayed for a minimum of 3 fields. These are the two original fields the
frame should have occupied, plus the one extra since the new frame still has
to wait for the correct field.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Fri, 3 Aug 2007 12:58:29 +0000 (09:58 -0300)]
V4L/DVB (5972): ivtv: prevent yuv register updates from being missed
The yuv output code always compares the new frame position & size with those
of the previous frame. If they are different, a flag is set to request the
yuv output registers be updated when the new frame is displayed.
If the incoming frames are delivered too fast, exhausting the buffers, the
most recent frame already buffered will be discarded. Unfortunately, any
update request will also be discarded. If the new frame matches the size &
position of the now discarded frame, the yuv registers are not flagged for
update & will remain in their old state.
This patch preserves the register update flag in the event that a frame is
dropped.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Fri, 3 Aug 2007 12:51:58 +0000 (09:51 -0300)]
V4L/DVB (5971): ivtv-fb: framebuffer timings no longer locked on module load
Framebuffer timings are currently locked to the video format in use when the
module is loaded. If the video format is then changed, the timings returned
by the framebuffer will be for the original format.
This patch ensures that the timings returned reflect the current video format.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Fri, 3 Aug 2007 12:44:13 +0000 (09:44 -0300)]
V4L/DVB (5970): ivtv: prevent vertical overflow of yuv output
When the video standard is changed, there's no guarantee the framebuffer
dimensions are still legal. The yuv output code uses these dimensions to
calculate the size & position for the video overlay. If the framebuffer
dimensions are now illegal, the output may exceed the vertical limit of the
display, causing distortion.
This patch adds an additional check to ensure the output doesn't exceed
the limits for the current video standard, cropping if required.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Janne Grunau [Tue, 31 Jul 2007 22:45:13 +0000 (19:45 -0300)]
V4L/DVB (5964): Fixed remote control for dib0700 with new firmware
The new firmware returns the data of the REQUEST_POLL_RC request in
reversed order. The default is RC5, but it can be adjusted using a
module parameter.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Matt Doran [Tue, 31 Jul 2007 10:09:30 +0000 (07:09 -0300)]
V4L/DVB (5960): Add module parameter to enable SFN workaround
In some areas in the world the broadcasters are not using the same
cellid for each transmitter in a SFN. The DiBcom has problems with
that setup. The module parameter buggy_sfn_workaround makes it re-usable.
Signed-off-by: Matt Doran <matt.doran@papercut.biz> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5955): Add support for DiB7070-based devices
This changeset adds support for DiB7070P-based devices by adding the
dib0070-driver and putting the appropriate layouts into
dib0700_devices.c
It also includes a new firmware for the dib0700 which is necessary to
make the DiB7070-boards work and it also should fix the i2c-problems
on some boards.
V4L/DVB (5954): Sync with DiBcom Driver Release 2.1.3 + some improvements
This changesets syncs the OpenSource driver for DiBcom demodulators
with version 2.1.3 of DiBcom reference driver. There were some
improvements since the last release for linux-dvb, e.g.:
- stepped AGC startup
- less space for initialization
- diversity synchronization
Furthermore this changeset contains the following things:
- latest AGC settings for MT2266-based devices (namely Nova-TD and other) will improve the sensitivity
- support for STK7700D reference design in dib0700-devices
- remove some line-breaks when debugging is enabled
- getting rid of layer between frontend_parameters and ofdm_channel used in dib*-drivers
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Steven Toth [Sat, 28 Jul 2007 22:34:52 +0000 (19:34 -0300)]
V4L/DVB (5948): Adding support for the S5H1409/CX24227 8VSB/QAM demodulator.
This patch adds support for the Samsung S5H1409 demodulator, also known
as the Conexant CX24227 demodulator. 8VSB mode has been tested and QAM
has been implemented based on the spec, although it's untested.
The S5H1409 / CX24227 appears on various Hauppauge boards.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Steven Toth [Sat, 28 Jul 2007 22:17:39 +0000 (19:17 -0300)]
V4L/DVB (5947): Adding support for the MT2131 tuner.
This adds support for the Microtune MT2131 tuner. 8VSB mode has been
tested but QAM support will likely require more register work. Hauppauge
have not announced any QAM devices using the MT2131 so QAM remains
undone.
For legal reasons, Microtune allowed us to write a GPL driver providing
we did not document in significant detail any of the registers. This
explains the lack of comments or defined on register names.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sun, 22 Jul 2007 15:52:40 +0000 (12:52 -0300)]
V4L/DVB (5922): ivtv, cx25840: postpone fw load until first use
The firmware is now loaded when the driver is actually used for the first
time. This allows the driver to be compiled in-kernel instead of as a module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5914): Add initial support for Dual-DVB-T stick
Add initial support for Dual-DVB-T stick based on DiB7700 and MT2266
- Microtune MT2266 driver.
- Preliminary support for these dual tuner devices :
- Pinnacle Dual DVB-T diversity
- Terratec Cinergy DT USB XS diversity
- Hauppauge Nova TD USB
Hans Verkuil [Fri, 20 Jul 2007 12:29:43 +0000 (09:29 -0300)]
V4L/DVB (5902): Add ivtv-fb framebuffer driver.
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com> Signed-off-by: Chris Kennedy <c@groovy.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: John P Harvey <john.p.harvey@btinternet.com> Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5897): dtt200u: add support for the Miglia TVMini USB DVB-T adapter
add code for autodetection and firmware download to the Miglia TVMini USB
DVB-T adapter. After firmware download, the device re-registers using
the WT220U_ZL0353_WARM usb id.
V4L/DVB (5885): zr36067: Fix problems with module parameters
Add permissions to all the module parameters so they can be queried and set
(when possible) via sysfs.
Add description for the vidmem parameter.
Change the video_nr parameter to an array, so that the video number can be
specified when a user has more than one card. The driver would try to give
all cards the same number otherwise, which will fail for all cards after the
first.
The default_input option would only allow values of 0 or 1, contrary to the
description. Allow values up to the number of inputs defined for the card.
Add description of lock_norm's different behavior for 1 and >1.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jean Delvare [Tue, 17 Jul 2007 21:29:41 +0000 (18:29 -0300)]
V4L/DVB (5884): zr36067: clean up debug function
Debugging cleanups to the zr36067 driver:
* Use module_param_named() to declare the debug parameter, so we can
use a single global variable to handle the debug level. This makes
the driver a bit smaller (by 648 bytes on x86_64), thanks to one
less level of indirection on every use.
* Change the debug parameter sysfs permissions, so that the debug
level can be adjusted at runtime, as is done in many other
media/video drivers.
* The debug level is between 0 and 5, not 0 and 4.
* Move the zr_debug export and dprintk macro definition to a header
file so that we don't have to define them in each source file.
* Simplify a duplicate test on zr_debug.
Note that zr_debug was subsequently renamed to debug_zr36067 to avoid
possible conflicts with other Zoran device drivers, on a suggestion
by Trent Piepho.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds an internal ioctl-like interface which can be used in
situations where a single Video4Linux device is implemented by multiple
device drivers. One master device controls one or more slave devices.
The slaves provide Video4Linux ioctl-like interface for the use of the
master.
Only a handful of ioctls are implemented at the moment. More can (and
should) be added as more functionality is required.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Linus Torvalds [Tue, 9 Oct 2007 19:38:44 +0000 (12:38 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Au1000: set the PCI controller IO base
[MIPS] Alchemy: Fix USB initialization.
[MIPS] IP32: Fix fatal typo in address computation.
Trond Myklebust [Tue, 9 Oct 2007 15:04:57 +0000 (11:04 -0400)]
NLM: Fix a memory leak in nlmsvc_testlock
The recent fix for a circular lock dependency unfortunately introduced a
potential memory leak in the event where the call to nlmsvc_lookup_host
fails for some reason.
Jeff Garzik [Tue, 9 Oct 2007 17:51:57 +0000 (13:51 -0400)]
sata_mv: correct S/G table limits
The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.
Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct Makefile rule for generating custom keymap
When building a custom keymap, after setting GENERATE_KEYMAP := 1 in
drivers/char/Makefile, the kernel build fails like this:
CC drivers/char/vt.o
make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'. Stop.
make[1]: *** [drivers/char] Error 2
make: *** [drivers] Error 2
This was caused by commit af8b128719f5248e542036ea994610a29d0642a6, which
deleted a necessary colon from the Makefile rule that generates the keymap,
since that rule contains both a target and a target-pattern. The following
patch puts the colon back:
Yan Zheng [Mon, 8 Oct 2007 19:16:20 +0000 (12:16 -0700)]
AIO: fix cleanup in io_submit_one(...)
When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect,
statement 'goto out_put_req' is executed. At label 'out_put_req',
aio_put_req(..) is called, which requires 'req->ki_filp' set.
Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yan Zheng [Mon, 8 Oct 2007 17:08:37 +0000 (10:08 -0700)]
fix page release issue in filemap_fault
find_lock_page increases page's usage count, we should decrease it
before return VM_FAULT_SIGBUS
Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Mon, 8 Oct 2007 16:54:37 +0000 (18:54 +0200)]
mm: set_page_dirty_balance() vs ->page_mkwrite()
All the current page_mkwrite() implementations also set the page dirty. Which
results in the set_page_dirty_balance() call to _not_ call balance, because the
page is already found dirty.
This allows us to dirty a _lot_ of pages without ever hitting
balance_dirty_pages(). Not good (tm).
Force a balance call if ->page_mkwrite() was successful.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brian Haley [Mon, 8 Oct 2007 07:12:05 +0000 (00:12 -0700)]
[IPv6]: Fix ICMPv6 redirect handling with target multicast address
When the ICMPv6 Target address is multicast, Linux processes the
redirect instead of dropping it. The problem is in this code in
ndisc_redirect_rcv():
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not
link-local.\n");
return;
}
This second check will succeed if the Target address is, for example,
FF02::1 because it has link-local scope. Instead, it should be checking
if it's a unicast link-local address, as stated in RFC 2461/4861 Section
8.1:
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
I know this doesn't explicitly say unicast link-local address, but it's
implied.
This bug is preventing Linux kernels from achieving IPv6 Logo Phase II
certification because of a recent error that was found in the TAHI test
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the
multicast address in the Destination field instead of Target field, so
we were passing the test. This won't be the case anymore.
The patch below fixes this problem, and also fixes ndisc_send_redirect()
to not send an invalid redirect with a multicast address in the Target
field. I re-ran the TAHI Neighbor Discovery section to make sure Linux
passes all 245 tests now.
Signed-off-by: Brian Haley <brian.haley@hp.com> Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 8 Oct 2007 06:44:17 +0000 (23:44 -0700)]
[ROSE]: Fix rose.ko oops on unload
Commit a3d384029aa304f8f3f5355d35f0ae274454f7cd aka
"[AX.25]: Fix unchecked rose_add_loopback_neigh uses"
transformed rose_loopback_neigh var into statically allocated one.
However, on unload it will be kfree's which can't work.
Ilpo Järvinen [Mon, 8 Oct 2007 06:43:10 +0000 (23:43 -0700)]
[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
When only GSO skb was partially ACKed, no hints are reset,
therefore fastpath_cnt_hint must be tweaked too or else it can
corrupt fackets_out. The corruption to occur, one must have
non-trivial ACK/SACK sequence, so this bug is not very often
that harmful. There's a fackets_out state reset in TCP because
fackets_out is known to be inaccurate and that fixes the issue
eventually anyway.
In case there was also at least one skb that got fully ACKed,
the fastpath_skb_hint is set to NULL which causes a recount for
fastpath_cnt_hint (the old value won't be accessed anymore),
thus it can safely be decremented without additional checking.
Reported by Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Torokhov [Sun, 7 Oct 2007 16:22:21 +0000 (12:22 -0400)]
Driver core: fix SYSF_DEPRECATED breakage for nested classdevs
We should only reparent to a class former class devices that
form the base of class hierarchy. Nested devices should still
grow from their real parents.
Al Viro [Sun, 7 Oct 2007 07:24:36 +0000 (00:24 -0700)]
fix bogus reporting of signals by audit
Async signals should not be reported as sent by current in audit log. As
it is, we call audit_signal_info() too early in check_kill_permission().
Note that check_kill_permission() has that test already - it needs to know
if it should apply current-based permission checks. So the solution is to
move the call of audit_signal_info() between those.
Bogosity in question is easily reproduced - add a rule watching for e.g.
kill(2) from specific process (so that audit_signal_info() would not
short-circuit to nothing), say load_policy, watch the bogus OBJ_PID entry
in audit logs claiming that write(2) on selinuxfs file issued by
load_policy(8) had somehow managed to send a signal to syslogd...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Steve Grubb <sgrubb@redhat.com> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafal Bilski [Sun, 7 Oct 2007 07:24:32 +0000 (00:24 -0700)]
Longhaul: add auto enabled "revid_errata" option
VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency. New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.
Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.
Same for Longhaul ver. 2 support. It will be disabled if none of above
options will work.
Best case scenario (with patch apllied and v2 enabled):
longhaul: VIA C3 'Ezra' [C5C] CPU detected. Longhaul v2 supported.
longhaul: Using northbridge support.
longhaul: VRM 8.5
longhaul: Max VID=1.350 Min VID=1.050, 13 possible voltage scales
longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
[...]
longhaul: Voltage scaling enabled.
Worst case scenario:
longhaul: VIA C3 'Ezra-T' [C5M] CPU detected. Powersaver supported.
longhaul: Using northbridge support.
longhaul: Using ACPI support.
longhaul: VRM 8.5
longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Disabling ACPI C3 support.
longhaul: Disabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
[akpm@linux-foundation.org: coding-style cleanups] Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Blanchard [Sun, 7 Oct 2007 07:24:31 +0000 (00:24 -0700)]
Fix timer_stats printout of events/sec
When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate. Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).
The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:17:38 +0000 (16:17 -0700)]
Don't do load-average calculations at even 5-second intervals
It turns out that there are a few other five-second timers in the
kernel, and if the timers get in sync, the load-average can get
artificially inflated by events that just happen to coincide.
So just offset the load average calculation it by a timer tick.
Noticed by Anders Boström, for whom the coincidence started triggering
on one of his machines with the JBD jiffies rounding code (JBD is one of
the subsystems that also end up using a 5-second timer by default).
Tested-by: Anders Boström <anders@bostrom.dyndns.org> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:02:55 +0000 (16:02 -0700)]
VT_WAITACTIVE: Avoid returning EINTR when not necessary
We should generally prefer to return ERESTARTNOHAND rather than EINTR,
so that processes with unhandled signals that get ignored don't return
EINTR.
This can help with X startup issues:
Fatal server error:
xf86OpenConsole: VT_WAITACTIVE failed: Interrupted system call
although the real fix is having the X server always retry EINTR
regardless (since EINTR does happen for signals that have handlers
installed). Keithp has a patch for that.
Regardless, ERESTARTNOHAND is the correct thing to use.
Fix non-terminated PCI match table in PowerMac IDE
The PCI device table in the powermac IDE driver isn't properly
terminated. Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.
Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck. In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <pmac@au1.ibm.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Heikki Lindholm <holindho@cs.helsinki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When pinning and unpinning pagetables, we must protect them against
being used by other CPUs, lest they see the pagetable in an
intermediate read-only-but-not-pinned state.
When using split pte locks, doing this properly would require taking
all the pte locks for the pagetable while pinning, but this may overflow
the PREEMPT_BITS part of the preempt counter if the process has mapped
more than about 512M of memory.
However, failing to take the pte locks causes write-protect faults when
the pageout code is trying to clear the Access bit on a pte which is part
of a freshy created and still being pinned process after fork.
This is a short-term fix until the problem is solved properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Hugh Dickins <hugh@veritas.com> Cc: David Rientjes <rientjes@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andi Kleen <ak@suse.de> Cc: Keir Fraser <keir@xensource.com> Cc: Jan Beulich <jbeulich@novell.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 5 Oct 2007 21:09:10 +0000 (14:09 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ben Dooks [Thu, 4 Oct 2007 22:16:42 +0000 (23:16 +0100)]
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 8169/8110SC currently announces itself as:
[...]
eth0: RTL8169sc/8110sc at 0x........, ..:..:..:..:..:.., XID 18000000 IRQ ..
^^^^^^^^
It uses RTL_GIGA_MAC_VER_05 and this part of the changeset can cut
its performance by a factor of 2~2.5 as reported by Timo.
(the driver includes code just before the hunk to write the ChipCmd
register when mac_version == RTL_GIGA_MAC_VER_0[1-4])
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Timo Jantunen <jeti@welho.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Fri, 5 Oct 2007 15:08:08 +0000 (08:08 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix 'niu' complex IRQ probing.
[SPARC64]: check fork_idle() error
[SPARC64]: Temporary workaround for PCI-E slot on T1000.
[SPARC64]: VIO device addition log message level is too high.
[SPARC64]: Fix domain-services port probing.
[SPARC64]: Don't use in/local regs for ldx/stx data in N1 memcpy.
Serge Belyshev [Thu, 4 Oct 2007 21:10:04 +0000 (23:10 +0200)]
Remove unnecessary cast in prefetch()
It is ok to call prefetch() function with NULL argument, as specifically
commented in include/linux/prefetch.h. But in standard C, it is invalid
to dereference NULL pointer (see C99 standard 6.5.3.2 paragraph 4 and
note #84).
prefetch() has a memory reference for its argument.
Newer gcc versions (4.3 and above) will use that to conclude that "x"
argument is non-null and thus wreaking havok everywhere prefetch() was
inlined.
Fixed by removing cast and changing asm constraint.
[ It seems in theory gcc 4.2 could miscompile this too; although no
cases known. In 2.6.24 we should probably switch to
__builtin_prefetch() instead, but this is a simpler fix for now.
-- AK ]
Giuseppe Sacco [Thu, 4 Oct 2007 21:09:12 +0000 (23:09 +0200)]
[MIPS] IP32: Enable PCI bridges
Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hugh Dickins [Thu, 4 Oct 2007 15:56:06 +0000 (16:56 +0100)]
Fix sys_remap_file_pages BUG at highmem.c:15!
Gurudas Pai reports kernel BUG at arch/i386/mm/highmem.c:15! below
sys_remap_file_pages, while running Oracle database test on x86 in 6GB
RAM: kunmap thinks we're in_interrupt because the preempt count has
wrapped.
That's because __do_fault expected to unmap page_table, but one of its
two callers do_nonlinear_fault already unmapped it: let do_linear_fault
unmap it first too, and then there's no need to pass the page_table arg
down.
Why have we been so slow to notice this? Probably through forgetting
that the mapping_cap_account_dirty test means that sys_remap_file_pages
nowadays only goes the full nonlinear vma route on a few memory-backed
filesystems like ramfs, tmpfs and hugetlbfs.
[ It also depends on CONFIG_HIGHPTE, so it becomes even harder to
trigger in practice. Many who have need of large memory have probably
migrated to x86-64..
projects / mirror_ubuntu-jammy-kernel.git / log