This is because acpi_debugger.lock has not been initialized as
acpi_debugger_init() is not called when ACPI is disabled. Fail module
loading to avoid this and any subsequent problems that might arise by
trying to debug AML when ACPI is disabled.
Fixes: 8cfb0cdf07e2 ("ACPI / debugger: Add IO interface to access debugger functionalities") Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Jamie Iles <jamie@nuviainc.com> Cc: 4.10+ <stable@vger.kernel.org> # 4.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
extlog_init() uses rdmsrl() to read an MSR, which on older CPUs
provokes a error message at boot:
unchecked MSR access error: RDMSR from 0x179 at rIP: 0xcd047307 (native_read_msr+0x7/0x40)
Use rdmsrl_safe() instead, and return -ENODEV if it fails.
Reported-by: jim@photojim.ca
References: https://bugs.debian.org/971058 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The original intent of 84d3f6b76447 was to delay evaluating lid state until
all drivers have been loaded, with input device being opened from userspace
serving as a signal for this condition. Let's ensure that state updates
happen even if userspace closed (or in the future inhibited) input device.
Note that if we go through suspend/resume cycle we assume the system has
been fully initialized even if LID input device has not been opened yet.
This has a side-effect of fixing access to input->users outside of
input->mutex protections by the way of eliminating said accesses and using
driver private flag.
Fixes: 84d3f6b76447 ("ACPI / button: Delay acpi_lid_initialize_state() until first user space open") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
We are generating incorrect path in case of rename retry because
we are restarting from wrong dentry. We should restart from the
dentry which was received in the call to nfs_path.
CC: stable@vger.kernel.org Signed-off-by: Ashish Sangwan <ashishsangwan2@gmail.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If block_write_full_page() is called for a page that is beyond current
inode size, it will truncate page buffers for the page and return 0.
This logic has been added in 2.5.62 in commit 81eb69062588 ("fix ext3
BUG due to race with truncate") in history.git tree to fix a problem
with ext3 in data=ordered mode. This particular problem doesn't exist
anymore because ext3 is long gone and ext4 handles ordered data
differently. Also normally buffers are invalidated by truncate code and
there's no need to specially handle this in ->writepage() code.
This invalidation of page buffers in block_write_full_page() is causing
issues to filesystems (e.g. ext4 or ocfs2) when block device is shrunk
under filesystem's hands and metadata buffers get discarded while being
tracked by the journalling layer. Although it is obviously "not
supported" it can cause kernel crashes like:
which is not great. The crash happens because bh->b_private is suddently
NULL although BH_JBD flag is still set (this is because
block_invalidatepage() cleared BH_Mapped flag and subsequent bh lookup
found buffer without BH_Mapped set, called init_page_buffers() which has
rewritten bh->b_private). So just remove the invalidation in
block_write_full_page().
Note that the buffer cache invalidation when block device changes size
is already careful to avoid similar problems by using
invalidate_mapping_pages() which skips busy buffers so it was only this
odd block_write_full_page() behavior that could tear down bdev buffers
under filesystem's hands.
Reported-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> CC: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
uvc_ctrl_add_info() calls uvc_ctrl_get_flags() which will override
the fixed-up flags set by uvc_ctrl_fixup_xu_info().
uvc_ctrl_init_xu_ctrl() already calls uvc_ctrl_get_flags() before
calling uvc_ctrl_add_info(), so the uvc_ctrl_get_flags() call in
uvc_ctrl_add_info() is not necessary for xu ctrls.
This commit moves the uvc_ctrl_get_flags() call for normal controls
from uvc_ctrl_add_info() to uvc_ctrl_init_ctrl(), so that we no longer
call uvc_ctrl_get_flags() twice for xu controls and so that we no longer
override the fixed-up flags set by uvc_ctrl_fixup_xu_info().
This fixes the xu motor controls not working properly on a Logitech
046d:08cc, and presumably also on the other Logitech models which have
a quirk for this in the uvc_ctrl_fixup_xu_info() function.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
These two drivers do not provide remove method and use devres for
allocation of other resources, yet they use led_classdev_register
instead of the devres variant, devm_led_classdev_register.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Álvaro Fernández Rojas <noltari@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jaedon Shin <jaedon.shin@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The driver uses atomic version of gpiod_set_value() without any real
reason. It is called in a workqueue under mutex so it could sleep
there. Changing it to "can_sleep" flavor allows to use the driver with
all GPIO chips.
Fixes: 4ed754de2d66 ("extcon: Add support for ptn5150 extcon driver") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If dma_request_chan() for TX channel fails with EPROBE_DEFER, the RX
channel would not be released and on next re-probe it would be requested
second time.
Fixes: 386119bc7be9 ("spi: sprd: spi: sprd: Add DMA mode support") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Chunyan Zhang <zhang.lyra@gmail.com> Link: https://lore.kernel.org/r/20200901152713.18629-1-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Neither IbsBrTarget nor OPDATA4 are populated in IBS Fetch mode.
Don't accumulate them into raw sample user data in that case.
Also, in Fetch mode, add saving the IBS Fetch Control Extended MSR.
Technically, there is an ABI change here with respect to the IBS raw
sample data format, but I don't see any perf driver version information
being included in perf.data file headers, but, existing users can detect
whether the size of the sample record has reduced by 8 bytes to
determine whether the IBS driver has this fix.
Fixes: 904cb3677f3a ("perf/x86/amd/ibs: Update IBS MSRs and feature definitions") Reported-by: Stephane Eranian <stephane.eranian@google.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200908214740.18097-6-kim.phillips@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
get_ibs_op_count() adds hardware's current count (IbsOpCurCnt) bits
to its count regardless of hardware's valid status.
According to the PPR for AMD Family 17h Model 31h B0 55803 Rev 0.54,
if the counter rolls over, valid status is set, and the lower 7 bits
of IbsOpCurCnt are randomized by hardware.
Don't include those bits in the driver's event count.
Fixes: 8b1e13638d46 ("perf/x86-ibs: Fix usage of IBS op current count") Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
An error occues when sampling non-PEBS INST_RETIRED.PREC_DIST(0x01c0)
event.
perf record -e cpu/event=0xc0,umask=0x01/ -- sleep 1
Error:
The sys_perf_event_open() syscall returned with 22 (Invalid argument)
for event (cpu/event=0xc0,umask=0x01/).
/bin/dmesg | grep -i perf may provide additional information.
The idxmsk64 of the event is set to 0. The event never be successfully
scheduled.
The event should be limit to the fixed counter 0.
Fixes: 6017608936c1 ("perf/x86/intel: Add Icelake support") Reported-by: Yi, Ammy <ammy.yi@intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200928134726.13090-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Currently, init_listener() tries to prevent adding a filter with
SECCOMP_FILTER_FLAG_NEW_LISTENER if one of the existing filters already
has a listener. However, this check happens without holding any lock that
would prevent another thread from concurrently installing a new filter
(potentially with a listener) on top of the ones we already have.
Theoretically, this is also a data race: The plain load from
current->seccomp.filter can race with concurrent writes to the same
location.
Fix it by moving the check into the region that holds the siglock to guard
against concurrent TSYNC.
(The "Fixes" tag points to the commit that introduced the theoretical
data race; concurrent installation of another filter with TSYNC only
became possible later, in commit 51891498f2da ("seccomp: allow TSYNC and
USER_NOTIF together").)
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace") Reviewed-by: Tycho Andersen <tycho@tycho.pizza> Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201005014401.490175-1-jannh@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400") Signed-off-by: Raul E Rangel <rrangel@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Some Intel BYT based host controllers support the setting of latency
tolerance. Accordingly, implement the PM QoS ->set_latency_tolerance()
callback. The raw register values are also exposed via debugfs.
Intel EHL controllers require this support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: cb3a7d4a0aec4e ("mmc: sdhci-pci: Add support for Intel EHL") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200818104508.7149-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This is because cache_size_mutex was unlocked too early in resize_stripes,
which races with grow_one_stripe() that grow_one_stripe() allocates a
stripe with wrong pool_size.
Fix this issue by unlocking cache_size_mutex after updating pool_size.
Cc: <stable@vger.kernel.org> # v4.4+ Reported-by: KoWei Sung <winders@amazon.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
A crash can happened when a connect is rejected. The host establishes
the connection after received ConnectReply, and then continues to send
the fabrics Connect command. If the controller does not receive the
ReadyToUse capsule, host may receive a ConnectReject reply.
Call nvme_rdma_destroy_queue_ib after the host received the
RDMA_CM_EVENT_REJECTED event. Then when the fabrics Connect command
times out, nvme_rdma_timeout calls nvme_rdma_complete_rq to fail the
request. A crash happenes due to use after free in
nvme_rdma_complete_rq.
nvme_rdma_destroy_queue_ib is redundant when handling the
RDMA_CM_EVENT_REJECTED event as nvme_rdma_destroy_queue_ib is already
called in connection failure handler.
Signed-off-by: Chao Leng <lengchao@huawei.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
sgl_alloc_order() can fail when 'length' is large on a memory
constrained system. When order > 0 it will potentially be
making several multi-page allocations with the later ones more
likely to fail than the earlier one. So it is important that
sgl_alloc_order() frees up any pages it has obtained before
returning NULL. In the case when order > 0 it calls the wrong
free page function and leaks. In testing the leak was
sufficient to bring down my 8 GiB laptop with OOM.
Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
There has one race case for ceph's rbd-nbd tool. When do mapping
it may fail with EBUSY from ioctl(nbd, NBD_DO_IT), but actually
the nbd device has already unmaped.
It dues to if just after the wake_up(), the recv_work() is scheduled
out and defers calling the nbd_config_put(), though the map process
has exited the "nbd->recv_task" is not cleared.
Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Jonathan Bakker <xc-racer2@live.ca> Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Jonathan Bakker <xc-racer2@live.ca> Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The fixed clocks are kept under dedicated 'external-clocks' node, thus a
fake 'reg' was added. This is not correct with dtschema as fixed-clock
binding does not have a 'reg' property. Moving fixed clocks out of
'soc' to root node fixes multiple dtbs_check warnings:
external-clocks: $nodename:0: 'external-clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
external-clocks: #size-cells:0:0: 0 is not one of [1, 2]
external-clocks: oscillator@0:reg:0: [0] is too short
external-clocks: oscillator@1:reg:0: [1] is too short
external-clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Jonathan Bakker <xc-racer2@live.ca> Link: https://lore.kernel.org/r/20200907161141.31034-7-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Callers are generally not supposed to check the return values from
debugfs functions. Debugfs functions never return NULL so this error
handling will never trigger. (Historically debugfs functions used to
return a mix of NULL and error pointers but it was eventually deemed too
complicated for something which wasn't intended to be used in normal
situations).
Delete all the error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Link: https://lore.kernel.org/r/20200826113759.GF393664@mwanda Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Some calls that set attributes, like utimensat(), are not supposed to return
-EINTR and thus do not have handlers for this in glibc which causes us
to leak -EINTR to the applications which are also unprepared to handle it.
For example tar will break if utimensat() return -EINTR and abort unpacking
the archive. Other applications may break too.
To handle this we add checks, and retry, for -EINTR in cifs_setattr()
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In gfs2_check_sb(), no validation checks are performed with regards to
the size of the superblock.
syzkaller detected a slab-out-of-bounds bug that was primarily caused
because the block size for a superblock was set to zero.
A valid size for a superblock is a power of 2 between 512 and PAGE_SIZE.
Performing validation checks and ensuring that the size of the superblock
is valid fixes this bug.
Reported-by: syzbot+af90d47a37376844e731@syzkaller.appspotmail.com Tested-by: syzbot+af90d47a37376844e731@syzkaller.appspotmail.com Suggested-by: Andrew Price <anprice@redhat.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
[Minor code reordering.] Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Use the same pattern as f2fs + ext4 where the kobject destruction must
complete before allowing the FS itself to be freed. This means that we
need an explicit free_sbd in the callers.
Cc: Bob Peterson <rpeterso@redhat.com> Cc: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Jamie Iles <jamie@nuviainc.com>
[Also go to fail_free when init_names fails.] Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The current nested KVM code does not support HPT guests. This is
informed/enforced in some ways:
- Hosts < P9 will not be able to enable the nested HV feature;
- The nested hypervisor MMU capabilities will not contain
KVM_CAP_PPC_MMU_HASH_V3;
- QEMU reflects the MMU capabilities in the
'ibm,arch-vec-5-platform-support' device-tree property;
- The nested guest, at 'prom_parse_mmu_model' ignores the
'disable_radix' kernel command line option if HPT is not supported;
- The KVM_PPC_CONFIGURE_V3_MMU ioctl will fail if trying to use HPT.
There is, however, still a way to start a HPT guest by using
max-compat-cpu=power8 at the QEMU machine options. This leads to the
guest being set to use hash after QEMU calls the KVM_PPC_ALLOCATE_HTAB
ioctl.
With the guest set to hash, the nested hypervisor goes through the
entry path that has no knowledge of nesting (kvmppc_run_vcpu) and
crashes when it tries to execute an hypervisor-privileged (mtspr
HDEC) instruction at __kvmppc_vcore_entry:
When we try to use file already used as a quota file again (for the same
or different quota type), strange things can happen. At the very least
lockdep annotations may be wrong but also inode flags may be wrongly set
/ reset. When the file is used for two quota types at once we can even
corrupt the file and likely crash the kernel. Catch all these cases by
checking whether passed file is already used as quota file and bail
early in that case.
This fixes occasional generic/219 failure due to lockdep complaint.
Reviewed-by: Andreas Dilger <adilger@dilger.ca> Reported-by: Ritesh Harjani <riteshh@linux.ibm.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20201015110330.28716-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In rdc321x_wdt_probe(), rdc321x_wdt_device.queue is initialized
after misc_register(), hence if ioctl is called before its
initialization which can call rdc321x_wdt_start() function,
it will see an uninitialized value of rdc321x_wdt_device.queue,
hence initialize it before misc_register().
Also, rdc321x_wdt_device.default_ticks is accessed in reset()
function called from write callback, thus initialize it before
misc_register().
Found by Linux Driver Verification project (linuxtesting.org).
In p9_fd_create_unix, checking is performed to see if the addr (passed
as an argument) is NULL or not.
However, no check is performed to see if addr is a valid address, i.e.,
it doesn't entirely consist of only 0's.
The initialization of sun_server.sun_path to be equal to this faulty
addr value leads to an uninitialized variable, as detected by KMSAN.
Checking for this (faulty addr) and returning a negative error number
appropriately, resolves this issue.
The open_req and open_ack completion variables are the state variables
to represet a remote channel as open. Use complete_all so there are no
races with waiters and using completion_done.
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The minus 1 is wrong, this branch should report 2048 bits of space.
With "-1" action, this only report 1024 bit of space.
This bug code returns wrong blocks, but it doesn't inflence bitmap logic:
1. Most callers focus this function return value (the counter of offset),
not the parameter blocks.
2. The bug is only triggered when hijacked is true or map is NULL.
the hijacked true condition is very rare.
the "map == null" only true when array is creating or resizing.
3. Even the caller gets wrong blocks, current code makes caller just to
call md_bitmap_get_counter() one more time.
Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If you replace a seed device in a sprouted fs, it appears to have
successfully replaced the seed device, but if you look closely, it
didn't. Here is an example.
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc started
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc finished
$ btrfs fi show
Label: none uuid: ab2c88b7-be81-4a7e-9849-c3666e7f9f4f
Total devices 2 FS bytes used 256.00KiB
devid 1 size 3.00GiB used 520.00MiB path /dev/sdc
devid 2 size 3.00GiB used 896.00MiB path /dev/sdb
Label: none uuid: 10bd3202-0415-43af-96a8-d5409f310a7e
Total devices 1 FS bytes used 128.00KiB
devid 1 size 3.00GiB used 536.00MiB path /dev/sda
So as per the replace start command and kernel log replace was successful.
Now let's try to clean mount.
$ umount /btrfs
$ btrfs device scan --forget
$ mount -o device=/dev/sdc /dev/sdb /btrfs
mount: /btrfs: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error.
Fix in this patch:
If a seed is not sprouted then there is no replacement of it, because of
its read-only filesystem with a read-only device. Similarly, in the case
of a sprouted filesystem, the seed device is still read only. So, mark
it as you can't replace a seed device, you can only add a new device and
then delete the seed device. If replace is attempted then returns
-EINVAL.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
xxx/arc/boot/dts/axs101.dt.yaml: dw-apb-ictl@e0012000: $nodename:0: \
'dw-apb-ictl@e0012000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
From schema: xxx/interrupt-controller/snps,dw-apb-ictl.yaml
The node name of the interrupt controller must start with
"interrupt-controller" instead of "dw-apb-ictl".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
[Why]
Currently mode validation is bypassed if remote sink exists. That
leads to mode set issue when a BW bottle neck exists in the link path,
e.g., a DP-to-HDMI converter that only supports HDMI 1.4.
Any invalid mode passed to Linux user space will cause the modeset
failure due to limitation of Linux user space implementation.
[How]
Mode validation is skipped only if in edid override. For real remote
sink, clock limit check should be done for HDMI remote sink.
Have HDMI related remote sink going through mode validation to
elimiate modes which pixel clock exceeds BW limitation.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Eryk Brol <eryk.brol@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In ACPI 6.3, the Memory Proximity Domain Attributes Structure
changed substantially. One of those changes was that the flag
for "Memory Proximity Domain field is valid" was deprecated.
This was because the field "Proximity Domain for the Memory"
became a required field and hence having a validity flag makes
no sense.
So the correct logic is to always assume the field is there.
Current code assumes it never is.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.
These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.
Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.
However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.
This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.
This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.
Cc: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Brcmfmac showed warning message in fweh.c when checking the size of event
queue which is not initialized. Therefore, we only cancel the worker and
reset event handler only when it is initialized.
The function should check the validity of the pxm value before using
it to index the pxm_to_node_map[] array.
Whilst hardening this code may be good in general, the main intent
here is to enable following patches that use this function to replace
acpi_map_pxm_to_node() for non SRAT usecases which should return
NO_NUMA_NODE for PXM entries not matching with those in SRAT.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Barry Song <song.bao.hua@hisilicon.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When callers pass XFS_BMAPI_REMAP into xfs_bunmapi, they want the extent
to be unmapped from the given file fork without the extent being freed.
We do this for non-rt files, but we forgot to do this for realtime
files. So far this isn't a big deal since nobody makes a bunmapi call
to a rt file with the REMAP flag set, but don't leave a logic bomb.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@tj.kylinos.cn> Reviewed-by: Gavin Shan <gshan@redhat.com> Link: https://lore.kernel.org/r/20200921023936.21846-1-liuzhengyuan@tj.kylinos.cn Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
uio_register_device() do two things.
1) get an uio id from a global pool, e.g. the id is <A>
2) create file nodes like /sys/class/uio/uio<A>
uio_unregister_device() do two things.
1) free the uio id <A> and return it to the global pool
2) free the file node /sys/class/uio/uio<A>
There is a situation is that one worker is calling uio_unregister_device(),
and another worker is calling uio_register_device().
If the two workers are X and Y, they go as below sequence,
1) X free the uio id <AAA>
2) Y get an uio id <AAA>
3) Y create file node /sys/class/uio/uio<AAA>
4) X free the file note /sys/class/uio/uio<AAA>
Then it will failed at the 3rd step and cause the phenomenon we saw as it
is creating a duplicated file node.
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for RISC-V at all even though ARCH_DLINFO will contain one NEW_AUX_ENT
for the VDSO address.
Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Reviewed-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Fix a possible deadlock in the l2fwd application in xdpsock that can
occur when there is no space in the Tx ring. There are two ways to get
the kernel to consume entries in the Tx ring: calling sendto() to make
it send packets and freeing entries from the completion ring, as the
kernel will not send a packet if there is no space for it to add a
completion entry in the completion ring. The Tx loop in l2fwd only
used to call sendto(). This patches adds cleaning the completion ring
in that loop.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/1599726666-8431-3-git-send-email-magnus.karlsson@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When tweaking llvm optimizations, I found that selftest build failed
with the following error:
libbpf: elf: skipping unrecognized data section(6) .rodata.str1.1
libbpf: prog 'sysctl_tcp_mem': bad map relo against '.L__const.is_tcp_mem.tcp_mem_name'
in section '.rodata.str1.1'
Error: failed to open BPF object file: Relocation failed
make: *** [/work/net-next/tools/testing/selftests/bpf/test_sysctl_prog.skel.h] Error 255
make: *** Deleting file `/work/net-next/tools/testing/selftests/bpf/test_sysctl_prog.skel.h'
The local string constant "tcp_mem_name" is put into '.rodata.str1.1' section
which libbpf cannot handle. Using untweaked upstream llvm, "tcp_mem_name"
is completely inlined after loop unrolling.
Commit 7fb5eefd7639 ("selftests/bpf: Fix test_sysctl_loop{1, 2}
failure due to clang change") solved a similar problem by defining
the string const as a global. Let us do the same here
for test_sysctl_prog.c so it can weather future potential llvm changes.
Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20200910202718.956042-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the above cg_skb(), to access array->map.max_entries, with CORE, the clang will
generate two builtin's.
base = &m_array;
/* access array.map */
map_addr = __builtin_preserve_struct_access_info(base, 0, 0);
/* access array.map.max_entries */
max_entries_addr = __builtin_preserve_struct_access_info(map_addr, 0, 0);
max_entries = *max_entries_addr;
In the current llvm, if two builtin's are in the same function or
in the same function after inlining, the compiler is smart enough to chain
them together and generates like below:
base = &m_array;
max_entries = *(base + reloc_offset); /* reloc_offset = 0 in this case */
and we are fine.
But if we force no inlining for one of functions in test_map_ptr() selftest, e.g.,
check_default(), the above two __builtin_preserve_* will be in two different
functions. In this case, we will have code like:
func check_hash():
reloc_offset_map = 0;
base = &m_array;
map_base = base + reloc_offset_map;
check_default(map_base, ...)
func check_default(map_base, ...):
max_entries = *(map_base + reloc_offset_max_entries);
On my system the kernel processes the "kgdb_earlycon" parameter before
the "kgdbcon" parameter. When we setup "kgdb_earlycon" we'll end up
in kgdb_register_callbacks() and "kgdb_use_con" won't have been set
yet so we'll never get around to starting "kgdbcon". Let's remedy
this by detecting that the IO module was already registered when
setting "kgdb_use_con" and registering the console then.
As part of this, to avoid pre-declaring things, move the handling of
the "kgdbcon" further down in the file.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200630151422.1.I4aa062751ff5e281f5116655c976dff545c09a46@changeid Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The .bss section for the h8300 is relatively small. A value of
CONFIG_LOG_BUF_SHIFT that is larger than 19 will create a static
printk ringbuffer that is too large. Limit the range appropriately
for the H8300.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20200812073122.25412-1-john.ogness@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the absence of ACPI or DT topology data, we fallback to haphazardly
decoding *something* out of MPIDR. Sadly, the contents of that register are
mostly unusable due to the implementation leniancy and things like Aff0
having to be capped to 15 (despite being encoded on 8 bits).
Consider a simple system with a single package of 32 cores, all under the
same LLC. We ought to be shoving them in the same core_sibling mask, but
MPIDR is going to look like:
The scheduler's MC domain (all CPUs with same LLC) is going to be built via
arch_topology.c::cpu_coregroup_mask()
In there we try to figure out a sensible mask out of the topology
information we have. In short, here we'll pick the smallest of NUMA or
core sibling mask.
MC mask for CPU16 will thus be 16-19... Uh oh. CPUs 16-19 are in two
different unique MC spans, and the scheduler has no idea what to make of
that. That triggers the WARN_ON() added by commit
We could try to come up with some cleverer scheme to figure out which of
the available masks to pick, but really if one of those masks resulted from
MPIDR then it should be discarded because it's bound to be bogus.
I was hoping to give MPIDR a chance for SMT, to figure out which threads are
in the same core using Aff1-3 as core ID, but Sudeep and Robin pointed out
to me that there are systems out there where *all* cores have non-zero
values in their higher affinity fields (e.g. RK3288 has "5" in all of its
cores' MPIDR.Aff1), which would expose a bogus core ID to userspace.
Stop using MPIDR for topology information. When no other source of topology
information is available, mark each CPU as its own core and its NUMA node
as its LLC domain.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Link: https://lore.kernel.org/r/20200829130016.26106-1-valentin.schneider@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
tw5864-video.c:773:32: warning: The left expression of the compound
assignment is an uninitialized value.
The computed value will also be garbage
fintv->stepwise.max.numerator *= std_max_fps;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
stepwise.max is set with frameinterval, which comes from
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
The default RGB quantization range for BT.2020 is full range (just as for
all the other RGB pixel encodings), not limited range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT macro and documentation
accordingly.
Also mention that HSV is always full range and cannot be limited range.
When RGB BT2020 was introduced in V4L2 it was not clear whether it should
be limited or full range, but full range is the right (and consistent)
choice.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The realtime bitmap and summary files are regular files that are hidden
away from the directory tree. Since they're regular files, inode
inactivation will try to purge what it thinks are speculative
preallocations beyond the incore size of the file. Unfortunately,
xfs_growfs_rt forgets to update the incore size when it resizes the
inodes, with the result that inactivating the rt inodes at unmount time
will cause their contents to be truncated.
Fix this by updating the incore size when we change the ondisk size as
part of updating the superblock. Note that we don't do this when we're
allocating blocks to the rt inodes because we actually want those blocks
to get purged if the growfs fails.
This fixes corruption complaints from the online rtsummary checker when
running xfs/233. Since that test requires rmap, one can also trigger
this by growing an rt volume, cycling the mount, and creating rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit 6f24ff97e323 ("power: supply: bq27xxx_battery: Add the
BQ27Z561 Battery monitor") and commit d74534c27775 ("power:
bq27xxx_battery: Add support for additional bq27xxx family devices")
added support for new device types by copying most of the code and
adding necessary quirks.
However they did not copy the code in bq27xxx_battery_status()
responsible for returning POWER_SUPPLY_STATUS_NOT_CHARGING.
Unify the bq27xxx_battery_status() so for all types when charger is
supplied, it will return "not charging" status.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This is commit fdfeff0f9e3d ("arm64: hw_breakpoint: Handle inexact
watchpoint addresses") but ported to arm32, which has the same
problem.
This problem was found by Android CTS tests, notably the
"watchpoint_imprecise" test [1]. I tested locally against a copycat
(simplified) version of the test though.
Link: https://lkml.kernel.org/r/20191019111216.1.I82eae759ca6dc28a245b043f485ca490e3015321@changeid Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
First problem is we hit BUG_ON() in f2fs_get_sum_page given EIO on
f2fs_get_meta_page_nofail().
Quick fix was not to give any error with infinite loop, but syzbot caught
a case where it goes to that loop from fuzzed image. In turned out we abused
f2fs_get_meta_page_nofail() like in the below call stack.
INFO: task syz-executor178:6870 can't die for more than 143 seconds.
task:syz-executor178 state:R
stack:26960 pid: 6870 ppid: 6869 flags:0x00004006
Call Trace:
Showing all locks held in the system:
1 lock held by khungtaskd/1179:
#0: ffffffff8a554da0 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6242
1 lock held by systemd-journal/3920:
1 lock held by in:imklog/6769:
#0: ffff88809eebc130 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:930
1 lock held by syz-executor178/6870:
#0: ffff8880925120e0 (&type->s_umount_key#47/1){+.+.}-{3:3}, at: alloc_super+0x201/0xaf0 fs/super.c:229
Actually, we didn't have to use _nofail in this case, since we could return
error to mount(2) already with the error handler.
As a result, this patch tries to 1) remove _nofail callers as much as possible,
2) deal with error case in last remaining caller, f2fs_get_sum_page().
Reported-by: syzbot+ee250ac8137be41d7b13@syzkaller.appspotmail.com Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Currently we overflow save_area_sync and write over
save_area_async. Although this is not a real problem make
startup_pgm_check_handler consistent with late pgm check handler and
store [%r0,%r7] directly into gpregs_save_area.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
@blkno in f2fs_ra_meta_pages could exceed max segment count, causing panic
in following sanity check in current_sit_addr(), add check condition to
avoid this issue.
Reported-by: syzbot+3698081bcf0bb2d12174@syzkaller.appspotmail.com Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In f2fs_lookup(), @res_page could be used before being initialized,
because in __f2fs_find_entry(), once F2FS_I(dir)->i_current_depth was
been fuzzed to zero, then @res_page will never be initialized, causing
this kmsan warning, relocating @res_page initialization place to fix
this bug.
Reported-by: syzbot+0eac6f0bbd558fd866d7@syzkaller.appspotmail.com Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The de facto (and apparently uncommented) standard for using an mm had,
thanks to this code in sparc if nothing else, been that you must have a
reference on mm_users *and that reference must have been obtained with
mmget()*, i.e., from a thread with a reference to mm_users that had used
the mm.
The introduction of mmget_not_zero() in commit d2005e3f41d4
("userfaultfd: don't pin the user memory in userfaultfd_file_create()")
allowed mm_count holders to aoperate on user mappings asynchronously
from the actual threads using the mm, but they were not to load those
mappings into their TLB (i.e., walking vmas and page tables is okay,
kthread_use_mm() is not).
io_uring 2b188cc1bb857 ("Add io_uring IO interface") added code which
does a kthread_use_mm() from a mmget_not_zero() refcount.
The problem with this is code which previously assumed mm == current->mm
and mm->mm_users == 1 implies the mm will remain single-threaded at
least until this thread creates another mm_users reference, has now
broken.
arch/sparc/kernel/smp_64.c:
if (atomic_read(&mm->mm_users) == 1) {
cpumask_copy(mm_cpumask(mm), cpumask_of(cpu));
goto local_flush_and_out;
}
vs fs/io_uring.c
if (unlikely(!(ctx->flags & IORING_SETUP_SQPOLL) ||
!mmget_not_zero(ctx->sqo_mm)))
return -EFAULT;
kthread_use_mm(ctx->sqo_mm);
mmget_not_zero() could come in right after the mm_users == 1 test, then
kthread_use_mm() which sets its CPU in the mm_cpumask. That update could
be lost if cpumask_copy() occurs afterward.
I propose we fix this by allowing mmget_not_zero() to be a first-class
reference, and not have this obscure undocumented and unchecked
restriction.
The basic fix for sparc64 is to remove its mm_cpumask clearing code. The
optimisation could be effectively restored by sending IPIs to mm_cpumask
members and having them remove themselves from mm_cpumask. This is more
tricky so I leave it as an exercise for someone with a sparc64 SMP.
powerpc has a (currently similarly broken) example.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
powerpc uses IPIs in some situations to switch a kernel thread away
from a lazy tlb mm, which is subject to the TLB flushing race
described in the changelog introducing ARCH_WANT_IRQS_OFF_ACTIVATE_MM.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-3-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Reading and modifying current->mm and current->active_mm and switching
mm should be done with irqs off, to prevent races seeing an intermediate
state.
This is similar to commit 38cf307c1f20 ("mm: fix kthread_use_mm() vs TLB
invalidate"). At exec-time when the new mm is activated, the old one
should usually be single-threaded and no longer used, unless something
else is holding an mm_users reference (which may be possible).
Absent other mm_users, there is also a race with preemption and lazy tlb
switching. Consider the kernel_execve case where the current thread is
using a lazy tlb active mm:
If we switch back to the kernel thread from a different mm, there is a
double free of the old active_mm, and a missing free of the new one.
Closing this race only requires interrupts to be disabled while ->mm
and ->active_mm are being switched, but the TLB problem requires also
holding interrupts off over activate_mm. Unfortunately not all archs
can do that yet, e.g., arm defers the switch if irqs are disabled and
expects finish_arch_post_lock_switch() to be called to complete the
flush; um takes a blocking lock in activate_mm().
So as a first step, disable interrupts across the mm/active_mm updates
to close the lazy tlb preempt race, and provide an arch option to
extend that to activate_mm which allows architectures doing IPI based
TLB shootdowns to close the second race.
This is a bit ugly, but in the interest of fixing the bug and backporting
before all architectures are converted this is a compromise.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-2-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When building with W=1 we get the following warning:
arch/powerpc/platforms/powernv/smp.c: In function ‘pnv_smp_cpu_kill_self’:
arch/powerpc/platforms/powernv/smp.c:276:16: error: suggest braces around
empty body in an ‘if’ statement [-Werror=empty-body]
276 | cpu, srr1);
| ^
cc1: all warnings being treated as errors
The full context is this block:
if (srr1 && !generic_check_cpu_restart(cpu))
DBG("CPU%d Unexpected exit while offline srr1=%lx!\n",
cpu, srr1);
When building with DEBUG undefined DBG() expands to nothing and GCC emits
the warning due to the lack of braces around an empty statement.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200804005410.146094-2-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If should_futex_fail() returns true in futex_wake_pi(), then the 'ret'
variable is set to -EFAULT and then immediately overwritten. So the failure
injection is non-functional.
Fix it by actually leaving the function and returning -EFAULT.
The Fixes tag is kinda blury because the initial commit which introduced
failure injection was already sloppy, but the below mentioned commit broke
it completely.
[ tglx: Massaged changelog ]
Fixes: 6b4f4bc9cb22 ("locking/futex: Allow low-level atomic operations to return -EAGAIN") Signed-off-by: Mateusz Nosek <mateusznosek0@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20200927000858.24219-1-mateusznosek0@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
ata_qc_complete_multiple() has to be called with the tags physically
active, that is the hw tag is at bit 0. ap->qc_active has the same tag
at bit ATA_TAG_INTERNAL instead, so call ata_qc_get_active() to fix that
up. This is done in the vein of 8385d756e114 ("libata: Fix retrieving of
active qcs").
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
Memory state around the buggy address: ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
GCC 10 optimizes the scheduler code differently than its predecessors.
When CONFIG_DEBUG_SECTION_MISMATCH=y, the Makefile forces GCC not
to inline some functions (-fno-inline-functions-called-once). Before GCC
10, "no-inlined" __schedule() starts with the usual prologue:
push %bp
mov %sp, %bp
So the ORC unwinder simply picks stack pointer from %bp and
unwinds from __schedule() just perfectly:
But now, with GCC 10, there is no %bp prologue in __schedule():
$ cat /proc/1/stack
<nothing>
The ORC entry of the point in __schedule() is:
sp:sp+88 bp:last_sp-48 type:call end:0
In this case, nobody subtracts sizeof "struct inactive_task_frame" in
__unwind_start(). The struct is put on the stack by __switch_to_asm() and
only then __switch_to_asm() stores %sp to task->thread.sp. But we start
unwinding from a point in __schedule() (stored in frame->ret_addr by
'call') and not in __switch_to_asm().
0xffffffff9376cad0 is __schedule+0x1f0 (after the call to
__switch_to_asm). Now follow those 88 bytes from the ORC entry (sp+88).
The entry is correct, __schedule() really pushes 48 bytes (8*7) + 32 bytes
via subq to store some local values (like 4U below). So to unwind, look
at the offset 88-sizeof(long) = 0x50 from here:
Here ^^^^^^^^^^^^^^^^ is the correct ret addr from
__schedule(). It translates to schedule+0x42 (insn after a call to
__schedule()).
BUT, unwind_next_frame() tries to take the address starting from
0xffff94b50001fdc8. That is exactly from thread.sp+88-sizeof(long) =
0xffff94b50001fdc8+88-8 = 0xffff94b50001fe18, which is garbage marked as
NOTE above. So this quits the unwinding as 7793fab6956b2d00 is obviously
not a kernel address.
There was a fix to skip 'struct inactive_task_frame' in
unwind_get_return_address_ptr in the following commit:
187b96db5ca7 ("x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks")
But we need to skip the struct already in the unwinder proper. So
subtract the size (increase the stack pointer) of the structure in
__unwind_start() directly. This allows for removal of the code added by
commit 187b96db5ca7 completely, as the address is now at
'(unsigned long *)state->sp - 1', the same as in the generic case.
[ mingo: Cleaned up the changelog a bit, for better readability. ]
Few commands provide the list of description partially and require
to be called consecutively until all the descriptors are fetched
completely. In such cases, we don't release the buffers and reuse
them for consecutive transmits.
However, currently we don't reset the Rx size which will be set as
per the response for the last transmit. This may result in incorrect
response size being interpretted as the firmware may repond with size
greater than the one set but we read only upto the size set by previous
response.
Let us reset the receive buffer size to max possible in such cases as
we don't know the exact size of the response.
Link: https://lore.kernel.org/r/20201012141746.32575-1-sudeep.holla@arm.com Fixes: b6f20ff8bd94 ("firmware: arm_scmi: add common infrastructure and support for base protocol") Reported-by: Etienne Carriere <etienne.carriere@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to avoid high dom0 load due to rogue guests sending events at
high frequency, block those events in case there was no action needed
in dom0 to handle the events.
This is done by adding a per-event counter, which set to zero in case
an EOI without the XEN_EOI_FLAG_SPURIOUS is received from a backend
driver, and incremented when this flag has been set. In case the
counter is 2 or higher delay the EOI by 1 << (cnt - 2) jiffies, but
not more than 1 second.
In order not to waste memory shorten the per-event refcnt to two bytes
(it should normally never exceed a value of 2). Add an overflow check
to evtchn_get() to make sure the 2 bytes really won't overflow.
This is part of XSA-332.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log