Laurent Pinchart [Tue, 10 Jun 2014 14:51:34 +0000 (11:51 -0300)]
[media] omap3isp: ccdc: Disable the video port when unused
The video port doesn't support YUV formats. Disable it when the CCDC
sink pad format is set to YUV instead of leaving it enabled and relying
on downstream modules not to process data they receive from the video
port.
Experiments showed that this fixes some of the CCDC failures to stop,
especially in BT.656 mode.
Laurent Pinchart [Tue, 20 May 2014 17:18:53 +0000 (14:18 -0300)]
[media] omap3isp: ccdc: Add support for BT.656 YUV format at the CCDC input
Query the CCDC input media bus type from the subdev connected to the
CCDC sink pad and configure the CCDC accordingly to support BT.656
synchronization.
Laurent Pinchart [Mon, 19 May 2014 19:37:38 +0000 (16:37 -0300)]
[media] omap3isp: ccdc: Add basic support for interlaced video
When the CCDC input is interlaced enable the alternate field order on
the CCDC output video node. The field signal polarity is specified
through platform data.
Laurent Pinchart [Mon, 19 May 2014 13:33:15 +0000 (10:33 -0300)]
[media] omap3isp: Move non-critical code out of the mutex-protected section
The isp_video_pix_to_mbus() and isp_video_mbus_to_pix() calls in
isp_video_set_format() only access static fields of the isp_video
structure. They don't need to be protected by a mutex.
Laurent Pinchart [Mon, 19 May 2014 14:36:23 +0000 (11:36 -0300)]
[media] v4l: subdev: Extend default link validation to cover field order
The field order must match between the source and sink pads, or the sink
pad field order must be NONE. This allows connecting an interlaced
source to a bridge that has no hardware support for interlaced formats.
Sakari Ailus [Wed, 21 May 2014 19:58:11 +0000 (16:58 -0300)]
[media] smiapp: Implement the test pattern control
Add support for the V4L2_CID_TEST_PATTERN control. When the solid colour
mode is selected, additional controls become available for setting the
solid four solid colour components.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sakari Ailus [Wed, 28 May 2014 12:38:21 +0000 (09:38 -0300)]
[media] v4l: Add test pattern colour component controls
In many cases the test pattern has selectable values for each colour
component. Implement controls for raw bayer components. Additional controls
should be defined for colour components that are not covered by these
controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
xc5000_set_params() is a bad name for a function that
handles only digital TV. Rename it to xc5000_set_digital_params(),
and proper name the generic function that works for both
digital and analog.
[media] xc5000: Split config and set code for analog/radio
As we need a function that reapply the last tuned radio,
in order to do resume, split the code that validates and
updates the internal priv struct from the ones that
actually set radio and TV.
[media] au0828: move the code that sets DTV on a separate function
As we'll be adding a code to resume tuner operation, we
need to move the code that actually sets DTV on a separate
function, to be called by the resume code.
[media] dvb-frontend: add core support for tuner suspend/resume
While several tuners have some sort of suspend/resume
implementation, this is currently mangled with an optional
.sleep callback that it is also used to put the device on
low power mode.
Not all drivers implement it, as returning the driver from
low power may require to re-load the firmware, with takes
some time. Also, some drivers may delay it.
So, the more coherent is to add two new optional callbacks
that will let the tuners to directy implement suspend and
resume callbacks if they need.
[media] au0828: don't let the IR polling thread to run at suspend
Trying to make au0828 to suspend can do very bad things, as
the polling Kthread is not handled. We should disable it
during suspend, only re-enabling it at resume.
Still, analog and digital TV won't work, as we don't reinit
the settings at resume, but at least it won't hang.
Shuah Khan [Sat, 9 Aug 2014 00:36:18 +0000 (21:36 -0300)]
[media] au0828: add au0828_rc_*() stubs for VIDEO_AU0828_RC disabled case
Define au0828_rc_*() stubs to avoid compile errors when
VIDEO_AU0828_RC is disabled and avoid the need to enclose
au0828_rc_*() in ifdef CONFIG_VIDEO_AU0828_RC in .c files.
[media] au0828-input: Be sure that IR is enabled at polling
When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.
Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Linus Torvalds [Sat, 16 Aug 2014 15:32:27 +0000 (09:32 -0600)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"A moderate number of changes, but nothing awfully significant.
A lot of const cleanups, some reworking and additions to the rfkill
quirks in the asus driver, a new driver for generating falling laptop
events on Toshibas and some misc fixes.
Maybe vendors have stopped inventing things"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
platform/x86: Enable build support for toshiba_haps
Documentation: Add file about toshiba_haps module
platform/x86: Toshiba HDD Active Protection Sensor
asus-nb-wmi: Add wapf4 quirk for the U32U
alienware-wmi: make hdmi_mux enabled on case-by-case basis
ideapad-laptop: Constify DMI table and other r/o variables
asus-nb-wmi.c: Rename x401u quirk to wapf4
compal-laptop: correct invalid hwmon name
toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
toshiba_acpi: Add extra check to backlight code
Fix log message about future removal of interface
ideapad-laptop: Disable touchpad interface on Yoga models
asus-nb-wmi: Add wapf4 quirk for the X550CC
intel_ips: Make ips_mcp_limits variables static
thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
hp-wmi: Add missing __init annotations to initialization code
hp_accel: Constify ACPI and DMI tables
fujitsu-tablet: Mark DMI callbacks as __init code
dell-laptop: Mark dell_quirks[] DMI table as __initconst
...
Linus Torvalds [Sat, 16 Aug 2014 15:25:34 +0000 (09:25 -0600)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
"Two Intel-platform-specific updates to intel_idle, and a cosmetic
tweak to the turbostat utility"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: tweak whitespace in output format
intel_idle: Broadwell support
intel_idle: Disable Baytrail Core and Module C6 auto-demotion
Linus Torvalds [Sat, 16 Aug 2014 15:24:41 +0000 (09:24 -0600)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fix from Rusty Russell:
"Nasty potential bug if someone uses a known module param with an
invalid value (we don't fail unknown module params any more, just
warn)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: Clean up ro/nx after early module load failures
Linus Torvalds [Sat, 16 Aug 2014 15:06:55 +0000 (09:06 -0600)]
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"These are all fixes I'd like to get out to a broader audience.
The biggest of the bunch is Mark's quota fix, which is also in the
SUSE kernel, and makes our subvolume quotas dramatically more
accurate.
I've been running xfstests with these against your current git
overnight, but I'm queueing up longer tests as well"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: disable strict file flushes for renames and truncates
Btrfs: fix csum tree corruption, duplicate and outdated checksums
Btrfs: Fix memory corruption by ulist_add_merge() on 32bit arch
Btrfs: fix compressed write corruption on enospc
btrfs: correctly handle return from ulist_add
btrfs: qgroup: account shared subtrees during snapshot delete
Btrfs: read lock extent buffer while walking backrefs
Btrfs: __btrfs_mod_ref should always use no_quota
btrfs: adjust statfs calculations according to raid profiles
Linus Torvalds [Sat, 16 Aug 2014 14:58:47 +0000 (08:58 -0600)]
Merge tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux
Pull file locking bugfixes from Jeff Layton:
"Most of these patches are to fix a long-standing regression that crept
in when the BKL was removed from the file-locking code. The code was
converted to use a conventional spinlock, but some fl_release_private
ops can block and you can end up sleeping inside the lock.
There's also a patch to make /proc/locks show delegations as 'DELEG'"
* tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux:
locks: update Locking documentation to clarify fl_release_private behavior
locks: move locks_free_lock calls in do_fcntl_add_lease outside spinlock
locks: defer freeing locks in locks_delete_lock until after i_lock has been dropped
locks: don't reuse file_lock in __posix_lock_file
locks: don't call locks_release_private from locks_copy_lock
locks: show delegations as "DELEG" in /proc/locks
Linus Torvalds [Sat, 16 Aug 2014 14:56:27 +0000 (08:56 -0600)]
Merge git://git.kvack.org/~bcrl/aio-next
Pull aio updates from Ben LaHaise.
* git://git.kvack.org/~bcrl/aio-next:
aio: use iovec array rather than the single one
aio: fix some comments
aio: use the macro rather than the inline magic number
aio: remove the needless registration of ring file's private_data
aio: remove no longer needed preempt_disable()
aio: kill the misleading rcu read locks in ioctx_add_table() and kill_ioctx()
aio: change exit_aio() to load mm->ioctx_table once and avoid rcu_read_lock()
Azael Avalos [Thu, 14 Aug 2014 15:55:38 +0000 (09:55 -0600)]
platform/x86: Toshiba HDD Active Protection Sensor
This driver adds support for the built-in accelereometer found
on recent Toshiba laptops with HID TOS620A.
This driver receives ACPI notify events 0x80 when the sensor
detects a sudden move or a harsh vibration, as well as an
ACPI notify event 0x81 whenever the movement or vibration has
been stabilized.
Also provides sysfs entries to get/set the desired protection
level and reseting the HDD protection interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
ideapad-laptop: Constify DMI table and other r/o variables
Constify the rfkill_blacklist[] DMI table, the ideapad_rfk_data[] table
and the ideapad_attribute_group attribute group. There's no need to have
them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ike Panhc <ike.pan@canonical.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Hans de Goede [Mon, 14 Jul 2014 07:14:34 +0000 (09:14 +0200)]
asus-nb-wmi.c: Rename x401u quirk to wapf4
The actual x401u does not use the so named x401u quirk but the x55u quirk.
All that the x401u quirk does it setting wapf to 4, so rename it to wapf4 to
stop the confusion.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Roald Frederickx [Wed, 13 Aug 2014 20:40:14 +0000 (13:40 -0700)]
compal-laptop: correct invalid hwmon name
Change the name of the hwmon interface from "compal-laptop" to "compal".
A dash is an invalid character for a hwmon name and caused the call to
hwmon_device_register_with_groups() to fail.
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Azael Avalos [Mon, 4 Aug 2014 15:21:01 +0000 (09:21 -0600)]
toshiba_acpi: Add extra check to backlight code
Some Toshiba models (most notably Qosmios) come with an
incomplete backlight method where the AML code doesn't
check for write or read commands and always returns
HCI_SUCCESS and the actual brightness (and in some
cases the max brightness), thus allowing the backlight
interface to be registered without write support.
This patch changes the set_lcd_brightness function,
checking the returned values for values greater than
zero to avoid registering a broken backlight interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
Mark volume_alsa_control_vol and volume_alsa_control_mute as __initdata,
as snd_ctl_new1() will copy the relevant parts, so there is no need to
keep the master copies around after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released afterwards -- roughly 1.5 kB.
In turn, the callback functions can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
dell-laptop: Mark dell_quirks[] DMI table as __initconst
The dell_quirks[] DMI table is only ever used during initialization.
Mark it as __initconst so its memory can be released afterwards --
roughly 5.7 kB. In turn, the callback function can be marked with
__init, too.
Also the touchpad_led_init() function can be marked __init as it's only
referenced from dell_init() -- an __init function.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Quite a lot of code and data of acer-wmi.c is only ever used during
initialization. Mark those accordingly -- and constify, where
appropriate -- so the memory can be released afterwards.
All in all those changes move ~10 kB of code and data to the .init
sections, marking them for release after initialization has finished.
The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released appropriately. In turn, the
callback function can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
acer-wmi: Hide acer_{suspend,resume} for !CONFIG_PM_SLEEP
Encapsulate acer_suspend() and acer_resume with #ifdef CONFIG_PM_SLEEP
to get rid of the following warnings:
../acer-wmi.c:2046:12: warning: ‘acer_suspend’ defined but not used [-Wunused-function]
../acer-wmi.c:2068:12: warning: ‘acer_resume’ defined but not used [-Wunused-function]
This patch removes the null test on block. block is initialized at the
beginning of the function to &wblock->gblock. Since wblock is
dereferenced prior to the null test, wblock must be a valid pointer,
and &wblock->gblock cannot be null.
The following Coccinelle script is used for detecting the change:
AceLan Kao [Wed, 9 Jul 2014 08:18:19 +0000 (16:18 +0800)]
asus-nb-wmi: Add ASUSTeK COMPUTER INC. X200CA
BIOS won't light on the wifi-led after S3, so asus-wmi driver needs to
control the wifi and wifi-led status.
But, it'll lead to bt status error if asus-wmi driver controls bt as well.
So, for X200CA, asus-wmi driver controls wifi status only and have to set
wapf to 1.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Hans de Goede [Tue, 8 Jul 2014 08:47:22 +0000 (10:47 +0200)]
asus-wmi: backlight_init: Stop treating -ENODEV as if its not an error
When bl_power support got added to asus-wmi, the error handling for it was
written to ignore -ENODEV, to avoid not registering a backlight interface for
models which have no bl_power control, but do have brightness control.
At the same time the error handling for brightness_max was modified to do the
same, this is wrong, when there is no brightness_max asus-wmi should not
register a backlight interface.
Note the caller of asus_wmi_backlight_init already special cases -ENODEV,
and will not cause the wmi driver regristration to fail because of a
-ENODEV return from asus_wmi_backlight_init.
Hans de Goede [Tue, 8 Jul 2014 08:47:21 +0000 (10:47 +0200)]
asus-wmi: Disable acpi-video backlight on desktop machines
Some Asus motherboards for desktop PC-s export an acpi-video interface
advertising backlight support. Test the dmi chassis-type and tell acpi-video
to not register a backlight interface on desktops.
Hans de Goede [Mon, 23 Jun 2014 14:45:51 +0000 (16:45 +0200)]
ideapad-laptop: Change Lenovo Yoga 2 series rfkill handling
It seems that the same problems which lead to adding an rfkill blacklist and
putting the Lenovo Yoga 2 11 on it are also present on the Lenovo Yoga 2 13
and Lenovo Yoga 2 Pro too:
https://bugzilla.redhat.com/show_bug.cgi?id=1021036
https://forums.lenovo.com/t5/Linux-Discussion/Yoga-2-13-not-Pro-Linux-Warning/m-p/1517612
Testing has shown that the firmware rfkill settings are persistent over
reboots. So blacklisting the driver is not good enough, if the wifi is blocked
at the firmware level the wifi needs to be explictly unblocked through the
ideapad-laptop interface.
And at least on the Lenovo Yoga 2 13 the VPCCMD_RF register which on devices
with hardware kill switch reports the hardware switch state, needs to be
explictly set to 1 (radio enabled / not blocked).
So this patch does 3 things to get proper rfkill handling on these models:
1) Instead of blacklisting the rfkill functionality, which means that people
with a firmware blocked wifi get stuck in that situation, ignore the value
reported by the not present hardware rfkill switch, as this is what is causing
ideapad-laptop to wrongly report all radios as hardware blocks. But do register
the rfkill interfaces so that the user can soft [un]block them.
2) On models without a hardware rfkill switch, explictly set VPCCMD_RF to 1
3) Drop the " 11" postfix from the dmi match string, as the entire Yoga 2
series is affected.
Yoga 2 11: Reported-and-tested-by: Vincent Gerris <vgerris@gmail.com>
Yoga 2 13: Tested-by: madls05 <http://ubuntuforums.org/showthread.php?t=2215044>
Yoga 2 Pro: Reported-and-tested-by: Peter F. Patel-Schneider <pfpschneider@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Hans de Goede [Mon, 23 Jun 2014 11:38:23 +0000 (13:38 +0200)]
thinkpad_acpi: Update mapping for F12 hotkey on *40 models to KEY_FILE
The new keyboard found on the *40 models is also being sold as a standalone
keyboard (with trackpoint):
http://shop.lenovo.com/us/en/itemdetails/0B47189/460/60AC6A0372B14F5BA7B12F1FF88E33C7
This uses a standard HUT code for the F12 key with the 6 square boxes on it,
which gets mapped to KEY_FILE by the kernel. Change the mapping done of
identical laptop key done by thinkpad_acpi to also send KEY_FILE for
consistency.
Cc: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Jean Delvare [Mon, 16 Jun 2014 09:55:13 +0000 (11:55 +0200)]
fujitsu-laptop: Clear build warnings
When CONFIG_FUJITSU_LAPTOP_DEBUG is disabled and W=1, the
fujitsu-laptop driver builds with the following warnings:
drivers/platform/x86/fujitsu-laptop.c: In function "bl_update_status":
drivers/platform/x86/fujitsu-laptop.c:409:8: warning: suggest braces around empty body in an "if" statement [-Wempty-body]
ret);
^
drivers/platform/x86/fujitsu-laptop.c:418:8: warning: suggest braces around empty body in an "if" statement [-Wempty-body]
ret);
^
Rework the debug printk helper macro to get rid of these. I verified
that this change has no effect on the generated binary, both in the
debug and non-debug case.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Jonathan Woithe <jwoithe@just42.net> Cc: Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Linus Torvalds [Sat, 16 Aug 2014 00:28:58 +0000 (18:28 -0600)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI changes from James Bottomley:
"This is a small set of updates which missed the first pull. It's more
msix updates, some iscsi and qla4xxx fixes, we also have some string
null termination fixes a return value fix and a couple of pm8001
firmware fixes.
Just a note, we do have a couple of bug fixes coming under separate
cover, but they don't have to be part of the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
iscsi class: Fix freeing of skb in get host error path
scsi: fix u14-34f printk format warnings
pm8001: fix pm8001_store_update_fw
pm8001: Fix erratic calculation in update_flash
pm8001: Update MAINTAINERS list
libiscsi: return new error code when nop times out
iscsi class: fix get_host_stats return code when not supported
iscsi class: fix get_host_stats error handling
qla4xxx: fix get_host_stats error propagation
qla4xxx: check the return value of dma_alloc_coherent()
scsi: qla4xxx: ql4_mbx.c: Cleaning up missing null-terminate in conjunction with strncpy
scsi: qla4xxx: ql4_os.c: Cleaning up missing null-terminate in conjunction with strncpy
qla4xxx: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Use pci_enable_msix_exact() instead of pci_enable_msix()
Linus Torvalds [Sat, 16 Aug 2014 00:16:28 +0000 (18:16 -0600)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
Linus Torvalds [Sat, 16 Aug 2014 00:06:56 +0000 (18:06 -0600)]
Merge tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is the additional fix patches that have been queued up since the
previous pull request. A few HD-audio fixes, a USB-audio quirk
addition, and a couple of trivial cleanup for the legacy OSS codes"
* tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set TLV_DB_SCALE_MUTE bit for cx5051 vmaster
ALSA: hda/ca0132 - Don't try loading firmware at resume when already failed
ALSA: hda - Fix pop noises on reboot for Dell XPS 13 9333
ALSA: hda - Set internal mic as default input source on Dell XPS 13 9333
ALSA: usb-audio: fix BOSS ME-25 MIDI regression
ALSA: hda - Fix parsing of CMI8888 codec
ALSA: hda - Fix probing and stuttering on CMI8888 HD-audio controller
ALSA: hda/realtek - Fixed ALC286/ALC288 recording delay for Headset Mic
sound: oss: Remove typedefs wanc_info and wavnc_port_info
sound: oss: uart401: Remove typedef uart401_devc
Linus Torvalds [Fri, 15 Aug 2014 23:57:49 +0000 (17:57 -0600)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes (mostly nouveau) from Dave Airlie:
"One doc buidling fixes for a file that moved, along with a bunch of
nouveau fixes, one a build problem on ARM"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/doc: Refer to proper source file
drm/nouveau/platform: fix compilation error
drm/nouveau/gk20a: add LTC device
drm/nouveau: warn if we fail to re-pin fb on resume
drm/nouveau/nvif: fix dac load detect method definition
drm/gf100-/gr: fix -ENOSPC detection when allocating zbc table entries
drm/nouveau/nvif: return null pointers on failure, in addition to ret != 0
drm/nouveau/ltc: fix tag base address getting truncated if above 4GiB
drm/nvc0-/fb/ram: fix use of non-existant ram if partitions aren't uniform
drm/nouveau/bar: behave better if ioremap failed
drm/nouveau/kms: nouveau_fbcon_accel_fini can be static
drm/nouveau: kill unused variable warning if !__OS_HAS_AGP
drm/nouveau/nvif: fix a number of notify thinkos
Linus Torvalds [Fri, 15 Aug 2014 23:56:45 +0000 (17:56 -0600)]
Merge branch 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull EDAC updates from Mauro Carvalho Chehab.
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: add support for Haswell based systems
sb_edac: Fix mix tab/spaces alignments
edac: add DDR4 and RDDR4
sb_edac: remove bogus assumption on mc ordering
sb_edac: make minimal use of channel_mask
sb_edac: fix socket detection on Ivy Bridge controllers
sb_edac: update Kconfig description
sb_edac: search devices using product id
sb_edac: make RIR limit retrieval per model
sb_edac: make node id retrieval per model
sb_edac: make memory type detection per memory controller
Andy Lutomirski [Fri, 15 Aug 2014 18:43:37 +0000 (04:13 +0930)]
module: Clean up ro/nx after early module load failures
The commit
4982223e51e8 module: set nx before marking module MODULE_STATE_COMING.
introduced a regression: if a module fails to parse its arguments or
if mod_sysfs_setup fails, then the module's memory will be freed
while still read-only. Anything that reuses that memory will crash
as soon as it tries to write to it.
Cc: stable@vger.kernel.org # v3.16 Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Chris Mason [Tue, 12 Aug 2014 17:47:42 +0000 (10:47 -0700)]
btrfs: disable strict file flushes for renames and truncates
Truncates and renames are often used to replace old versions of a file
with new versions. Applications often expect this to be an atomic
replacement, even if they haven't done anything to make sure the new
version is fully on disk.
Btrfs has strict flushing in place to make sure that renaming over an
old file with a new file will fully flush out the new file before
allowing the transaction commit with the rename to complete.
This ordering means the commit code needs to be able to lock file pages,
and there are a few paths in the filesystem where we will try to end a
transaction with the page lock held. It's rare, but these things can
deadlock.
This patch removes the ordered flushes and switches to a best effort
filemap_flush like ext4 uses. It's not perfect, but it should fix the
deadlocks.