Currently, it is not possible to migrate a neighbor entry between NUD_PERMANENT
state and NTF_USE flag with a dynamic NUD state from a user space control plane.
Similarly, it is not possible to add/remove NTF_EXT_LEARNED flag from an existing
neighbor entry in combination with NTF_USE flag.
This is due to the latter directly calling into neigh_event_send() without any
meta data updates as happening in __neigh_update(). Thus, to enable this use
case, extend the latter with a NEIGH_UPDATE_F_USE flag where we break the
NUD_PERMANENT state in particular so that a latter neigh_event_send() is able
to re-resolve a neighbor entry.
Before fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
As can be seen, despite the admin-triggered replace, the entry remains in the
NUD_PERMANENT state.
After fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn STALE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
After the fix, the admin-triggered replace switches to a dynamic state from
the NTF_USE flag which triggered a new neighbor resolution. Likewise, we can
transition back from there, if needed, into NUD_PERMANENT.
Similar before/after behavior can be observed for below transitions:
Before fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[..]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Roopa Prabhu <roopa@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We use inline_dentry which requires to allocate dentry page when adding a link.
If we allow to reclaim memory from filesystem, we do down_read(&sbi->cp_rwsem)
twice by f2fs_lock_op(). I think this should be okay, but how about stopping
the lockdep complaint [1]?
When using "devm_request_threaded_irq(,,,,IRQF_ONESHOT,,)" in a driver,
only the first interrupt is handled, and following interrupts are never
delivered (initially reported in [1]).
That's because the RISC-V PLIC cannot EOI masked interrupts, as explained
in the description of Interrupt Completion in the PLIC spec [2]:
<quote>
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored.
</quote>
Re-enable the interrupt before completion if it has been masked during
the handling, and remask it afterwards.
Fix a kernel crash which happens on PA1.x CPUs while initializing the
FTRACE/KPROBE breakpoints. The PTE table entries for the fixmap area
were not created correctly.
Naresh and Antonio ran into a build failure with latest Debian
armhf compilers, with lots of output like
tmp/ccY3nOAs.s:2215: Error: selected processor does not support `cpsid i' in ARM mode
As it turns out, $(cc-option) fails early here when the FPU is not
selected before CPU architecture is selected, as the compiler
option check runs before enabling -msoft-float, which causes
a problem when testing a target architecture level without an FPU:
cc1: error: '-mfloat-abi=hard': selected architecture lacks an FPU
Passing e.g. -march=armv6k+fp in place of -march=armv6k would avoid this
issue, but the fallback logic is already broken because all supported
compilers (gcc-5 and higher) are much more recent than these options,
and building with -march=armv5t as a fallback no longer works.
The best way forward that I see is to just remove all the checks, which
also has the nice side-effect of slightly improving the startup time for
'make'.
The -mtune=marvell-f option was apparently never supported by any mainline
compiler, and the custom Codesourcery gcc build that did support is
now too old to build kernels, so just use -mtune=xscale unconditionally
for those.
This should be safe to apply on all stable kernels, and will be required
in order to keep building them with gcc-11 and higher.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=996419 Reported-by: Antonio Terceiro <antonio.terceiro@linaro.org> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> Cc: Matthias Klose <doko@debian.org> Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently __set_fixmap() bails out with a warning when called in early boot
from early_iounmap(). Fix it, and while at it, make the comment a bit easier
to understand.
Cc: <stable@vger.kernel.org> Fixes: b089c31c519c ("ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap") Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.
This broke support for passing port (-p) on its own.
Configure sockaddr after parsing all arguments.
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.
Fixes: f56ec6766dcf ("cxgb4: Add support for ethtool i2c dump") Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We got the following WARNING when running ab/nginx
test with RDMA link flapping (up-down-up).
The reason is when smc_sock fallback and at linkdown
happens simultaneously, we may got the following situation:
smc_sock was set to SMC_CLOSED and sock_put() been called
when terminate the link group. But later application call
close() on the socket, then we got:
__smc_release():
if (smc_sock->fallback)
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
Again we set the smc_sock to CLOSED through it's already
in CLOSED state, and double put the refcnt, so the following
warning happens:
refcount_t: underflow; use-after-free.
WARNING: CPU: 5 PID: 860 at lib/refcount.c:28 refcount_warn_saturate+0x8d/0xf0
Modules linked in:
CPU: 5 PID: 860 Comm: nginx Not tainted 5.10.46+ #403
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/01/2014
RIP: 0010:refcount_warn_saturate+0x8d/0xf0
Code: 05 5c 1e b5 01 01 e8 52 25 bc ff 0f 0b c3 80 3d 4f 1e b5 01 00 75 ad 48
This patch adds check in __smc_release() to make
sure we won't do an extra sock_put() and set the
socket to CLOSED when its already in CLOSED state.
Fixes: 51f1de79ad8e (net/smc: replace sock_put worker by socket refcounting) Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently vosck_connect() increments sock refcount for nonblocking
socket each time it's called, which can lead to memory leak if
it's called multiple times because connect timeout function decrements
sock refcount only once.
Fixes it by making vsock_connect() return -EALREADY immediately when
sock state is already SS_CONNECTING.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes: 330baff5423b ("net: hns3: add ETS TC weight setting in SSU module") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
1) if q->tk_offset == TK_OFFS_MAX, then get_tcp_tstamp() calls
ktime_mono_to_any() with out-of-bound value.
2) if q->tk_offset is changed in taprio_parse_clockid(),
taprio_get_time() might also call ktime_mono_to_any()
with out-of-bound value as sysbot found:
UBSAN: array-index-out-of-bounds in kernel/time/timekeeping.c:908:27
index 3 is out of range for type 'ktime_t *[3]'
CPU: 1 PID: 25668 Comm: kworker/u4:0 Not tainted 5.15.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_out_of_bounds.cold+0x62/0x6c lib/ubsan.c:291
ktime_mono_to_any+0x1d4/0x1e0 kernel/time/timekeeping.c:908
get_tcp_tstamp net/sched/sch_taprio.c:322 [inline]
get_packet_txtime net/sched/sch_taprio.c:353 [inline]
taprio_enqueue_one+0x5b0/0x1460 net/sched/sch_taprio.c:420
taprio_enqueue+0x3b1/0x730 net/sched/sch_taprio.c:485
dev_qdisc_enqueue+0x40/0x300 net/core/dev.c:3785
__dev_xmit_skb net/core/dev.c:3869 [inline]
__dev_queue_xmit+0x1f6e/0x3630 net/core/dev.c:4194
batadv_send_skb_packet+0x4a9/0x5f0 net/batman-adv/send.c:108
batadv_iv_ogm_send_to_if net/batman-adv/bat_iv_ogm.c:393 [inline]
batadv_iv_ogm_emit net/batman-adv/bat_iv_ogm.c:421 [inline]
batadv_iv_send_outstanding_bat_ogm_packet+0x6d7/0x8e0 net/batman-adv/bat_iv_ogm.c:1701
process_one_work+0x9b2/0x1690 kernel/workqueue.c:2298
worker_thread+0x658/0x11f0 kernel/workqueue.c:2445
kthread+0x405/0x4f0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
Fixes: 7ede7b03484b ("taprio: make clock reference conversions easier") Fixes: 54002066100b ("taprio: Adjust timestamps for TCP packets") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vedang Patel <vedang.patel@intel.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Link: https://lore.kernel.org/r/20211108180815.1822479-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Strparser is reusing the qdisc_skb_cb struct to stash the skb message handling
progress, e.g. offset and length of the skb. First this is poorly named and
inherits a struct from qdisc that doesn't reflect the actual usage of cb[] at
this layer.
But, more importantly strparser is using the following to access its metadata.
So we use 12 bytes of ->data[] in struct. However in BPF code running parser
and verdict the user has read capabilities into the data[] array as well. Its
not too problematic, but we should not be exposing internal state to BPF
program. If its really needed then we can use the probe_read() APIs which allow
reading kernel memory. And I don't believe cb[] layer poses any API breakage by
moving this around because programs can't depend on cb[] across layers.
In order to fix another issue with a ctx rewrite we need to stash a temp
variable somewhere. To make this work cleanly this patch builds a cb struct
for sk_skb types called sk_skb_cb struct. Then we can use this consistently
in the strparser, sockmap space. Additionally we can start allowing ->cb[]
write access after this.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Jussi Maki <joamaki@gmail.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20211103204736.248403-5-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
gcc warns about undefined behavior the vmalloc code when building
with CONFIG_ARM64_PA_BITS_52, when the 'idx++' in the argument to
__phys_to_pte_val() is evaluated twice:
mm/vmalloc.c: In function 'vmap_pfn_apply':
mm/vmalloc.c:2800:58: error: operation on 'data->idx' may be undefined [-Werror=sequence-point]
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ~~~~~~~~~^~
arch/arm64/include/asm/pgtable-types.h:25:37: note: in definition of macro '__pte'
25 | #define __pte(x) ((pte_t) { (x) } )
| ^
arch/arm64/include/asm/pgtable.h:80:15: note: in expansion of macro '__phys_to_pte_val'
80 | __pte(__phys_to_pte_val((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot))
| ^~~~~~~~~~~~~~~~~
mm/vmalloc.c:2800:30: note: in expansion of macro 'pfn_pte'
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ^~~~~~~
I have no idea why this never showed up earlier, but the safest
workaround appears to be changing those macros into inline functions
so the arguments get evaluated only once.
Cc: Matthew Wilcox <willy@infradead.org> Fixes: 75387b92635e ("arm64: handle 52-bit physical addresses in page table entries") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20211105075414.2553155-1-arnd@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
skb is already freed by dev_kfree_skb in pn533_fill_fragment_skbs,
but follow error handler branch when pn533_fill_fragment_skbs()
fails, skb is freed again, results in double free issue. Fix this
by not free skb in error path of pn533_fill_fragment_skbs.
Fixes: 963a82e07d4e ("NFC: pn533: Split large Tx frames in chunks") Fixes: 93ad42020c2d ("NFC: pn533: Target mode Tx fragmentation support") Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Both ifindex and LLC_SK_DEV_HASH_ENTRIES are signed.
This means that (ifindex % LLC_SK_DEV_HASH_ENTRIES) is negative
if @ifindex is negative.
We could simply make LLC_SK_DEV_HASH_ENTRIES unsigned.
In this patch I chose to use hash_32() to get more entropy
from @ifindex, like llc_sk_laddr_hashfn().
UBSAN: array-index-out-of-bounds in ./include/net/llc.h:75:26
index -43 is out of range for type 'hlist_head [64]'
CPU: 1 PID: 20999 Comm: syz-executor.3 Not tainted 5.15.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_out_of_bounds.cold+0x62/0x6c lib/ubsan.c:291
llc_sk_dev_hash include/net/llc.h:75 [inline]
llc_sap_add_socket+0x49c/0x520 net/llc/llc_conn.c:697
llc_ui_bind+0x680/0xd70 net/llc/af_llc.c:404
__sys_bind+0x1e9/0x250 net/socket.c:1693
__do_sys_bind net/socket.c:1704 [inline]
__se_sys_bind net/socket.c:1702 [inline]
__x64_sys_bind+0x6f/0xb0 net/socket.c:1702
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fa503407ae9
Fixes: 6d2e3ea28446 ("llc: use a device based hash table to speed up multicast delivery") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If btf__new() is called then there needs to be a corresponding btf__free().
Fixes: f8dfeae009effc0b ("perf bpf: Show more BPF program info in print_bpf_prog_info()") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrii Nakryiko <andrii@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Cc: Yonghong Song <yhs@fb.com> Cc: bpf@vger.kernel.org Cc: netdev@vger.kernel.org Link: http://lore.kernel.org/lkml/20211106053733.3580931-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
snprintf() returns the number of bytes it would have printed if there
were space. But it does not count the NUL terminator. So that means
that if "count == copied" then this has already overflowed by one
character.
There is one possible race window between zs_pool_dec_isolated() and
zs_unregister_migration() because wait_for_isolated_drain() checks the
isolated count without holding class->lock and there is no order inside
zs_pool_dec_isolated(). Thus the below race window could be possible:
When I do fuzz test for bonding device interface, I got the following
use-after-free Calltrace:
==================================================================
BUG: KASAN: use-after-free in bond_enslave+0x1521/0x24f0
Read of size 8 at addr ffff88825bc11c00 by task ifenslave/7365
Last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
delayed_work_timer_fn+0x3e/0x50
call_timer_fn+0x148/0x470
run_timer_softirq+0x8a8/0xc50
__do_softirq+0x107/0x55f
Second to last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
__queue_delayed_work+0x130/0x180
queue_delayed_work_on+0xa7/0xb0
bond_enslave+0xe25/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Memory state around the buggy address: ffff88825bc11b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88825bc11b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88825bc11c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88825bc11c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88825bc11d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Put new_slave in bond_sysfs_slave_add() will cause use-after-free problems
when new_slave is accessed in the subsequent error handling process. Since
new_slave will be put in the subsequent error handling process, remove the
unnecessary put to fix it.
In addition, when sysfs_create_file() fails, if some files have been crea-
ted successfully, we need to call sysfs_remove_file() to remove them.
Since there are sysfs_create_files() & sysfs_remove_files() can be used,
use these two functions instead.
Fixes: 7afcaec49696 (bonding: use kobject_put instead of _del after kobject_add) Signed-off-by: Huang Guobin <huangguobin4@huawei.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The handling of PMIC register reads through writing 0 to address 4
of the OpRegion is wrong. Instead of returning the read value
through the value64, which is a no-op for function == ACPI_WRITE calls,
store the value and then on a subsequent function == ACPI_READ with
address == 3 (the address for the value field of the OpRegion)
return the stored value.
This has been tested on a Xiaomi Mi Pad 2 and makes the ACPI battery dev
there mostly functional (unfortunately there are still other issues).
Here are the SET() / GET() functions of the PMIC ACPI device,
which use this OpRegion, which clearly show the new behavior to
be correct:
The real_dev of a vlan net_device may be freed after
unregister_vlan_dev(). Access the real_dev continually by
vlan_dev_real_dev() will trigger the UAF problem for the
real_dev like following:
Move the put_device(real_dev) to vlan_dev_free(). Ensure
real_dev not be freed before vlan_dev unregistered.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+e4df4e1389e28972e955@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This patch allows to use 0 for `coal->rx_coalesce_usecs` param to
disable rx irq coalescing.
Previously we could enable rx irq coalescing via ethtool
(For ex: `ethtool -C eth0 rx-usecs 2000`) but we couldn't disable
it because this part rejects 0 value:
Return NULL instead of passing to ERR_PTR while err is zero,
this fix smatch warnings:
drivers/xen/xen-pciback/conf_space_capability.c:163
pm_ctrl_init() warn: passing zero to 'ERR_PTR'
Fixes: a92336a1176b ("xen/pciback: Drop two backends, squash and cleanup some code.") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20211008074417.8260-1-yuehaibing@huawei.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372e4 ("i2c: xlr: add support for Sigma Designs controller variant") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If we already hold open state on the client, yet the server gives us a
completely different stateid to the one we already hold, then we
currently treat it as if it were an out-of-sequence update, and wait for
5 seconds for other updates to come in.
This commit fixes the behaviour so that we immediately start processing
of the new stateid, and then leave it to the call to
nfs4_test_and_free_stateid() to decide what to do with the old stateid.
Fixes: b4868b44c562 ("NFSv4: Wait for stateid updates after CLOSE/OPEN_DOWNGRADE") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When user uses issue_lip to do link bounce, driver sends additional target
reset to remote device before resetting the link. The target reset would
affect other paths with active I/Os. This patch will remove the unnecessary
target reset.
Link: https://lore.kernel.org/r/20211026115412.27691-4-njavali@marvell.com Fixes: 5854771e314e ("[SCSI] qla2xxx: Add ISPFX00 specific bus reset routine") Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Avoid error like:
In file included from drivers/watchdog/ar7_wdt.c:29:
./arch/mips/include/asm/mach-ar7/ar7.h: In function ‘ar7_is_titan’:
./arch/mips/include/asm/mach-ar7/ar7.h:111:24: error: implicit declaration of function ‘KSEG1ADDR’; did you mean ‘CKSEG1ADDR’? [-Werror=implicit-function-declaration]
111 | return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
| ^~~~~~~~~
| CKSEG1ADDR
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible") Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210907024904.4127611-1-liu.yun@linux.dev Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The fintek watchdog timer can configure timeouts of second granularity
only up to 255 seconds. Beyond that, the timeout needs to be configured
with minute granularity. WDIOC_GETTIMEOUT should report the actual
timeout configured, not just echo back the timeout configured by the
user. Do so.
Fixes: 96cb4eb019ce ("watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG") Suggested-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Link: https://lore.kernel.org/r/5e17960fe8cc0e3cb2ba53de4730b75d9a0f33d5.1628525954.git-series.a.fatoum@pengutronix.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
'make randconfig' can produce a .config file with
"CONFIG_MEMORY_RESERVE=" (no value) since it has no default.
When a subsequent 'make all' is done, kconfig restarts the config
and prompts for a value for MEMORY_RESERVE. This breaks
scripting/automation where there is no interactive user input.
Add a default value for MEMORY_RESERVE. (Any integer value will
work here for kconfig.)
Fixes a kconfig warning:
.config:214:warning: symbol value '' invalid for MEMORY_RESERVE
* Restart config...
Memory reservation (MiB) (MEMORY_RESERVE) [] (NEW)
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") # from beginning of git history Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: linux-m68k@lists.linux-m68k.org Signed-off-by: Greg Ungerer <gerg@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Today the sh code allocates memory the first time a process uses
the fpu. If that memory allocation fails, kill the affected task
with force_sig(SIGKILL) rather than do_group_exit(SIGKILL).
Calling do_group_exit from an exception handler can potentially lead
to dead locks as do_group_exit is not designed to be called from
interrupt context. Instead use force_sig(SIGKILL) to kill the
userspace process. Sending signals in general and force_sig in
particular has been tested from interrupt context so there should be
no problems.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: linux-sh@vger.kernel.org Fixes: 0ea820cf9bf5 ("sh: Move over to dynamically allocated FPU context.") Link: https://lkml.kernel.org/r/20211020174406.17889-6-ebiederm@xmission.com Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Before the `callback_result` callback was introduced drivers coded their
invocation to the callback in a similar way to:
if (cb->callback) {
spin_unlock(&dma->lock);
cb->callback(cb->callback_param);
spin_lock(&dma->lock);
}
With the introduction of `callback_result` two helpers where introduced to
transparently handle both types of callbacks. And drivers where updated to
look like this:
if (dmaengine_desc_callback_valid(cb)) {
spin_unlock(&dma->lock);
dmaengine_desc_callback_invoke(cb, ...);
spin_lock(&dma->lock);
}
dmaengine_desc_callback_invoke() correctly handles both `callback_result`
and `callback`. But we forgot to update the dmaengine_desc_callback_valid()
function to check for `callback_result`. As a result DMA descriptors that
use the `callback_result` rather than `callback` don't have their callback
invoked by drivers that follow the pattern above.
Fix this by checking for both `callback` and `callback_result` in
dmaengine_desc_callback_valid().
Fixes: f067025bc676 ("dmaengine: add support to provide error result from a DMA transation") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20211023134101.28042-1-lars@metafoo.de Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Free the kbuf buffer before returning from the dpaa2_console_read()
function. The variable no longer goes out of scope, leaking the storage
it points to.
Fix this by providing a handler that always returns zero, to make sure
blank events will be sent to the actual device handling the backlight.
Reported-by: Robin van der Gracht <robin@protonic.nl> Suggested-by: Robin van der Gracht <robin@protonic.nl> Fixes: 8992da44c6805d53 ("auxdisplay: ht16k33: Driver for LED controller") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently /sys/class/graphics/fb0/bl_curve is not accessible (-ENODEV),
as the driver does not connect the backlight to the frame buffer device.
Fix this moving backlight initialization up, and filling in
fb_info.bl_dev.
Fixes: 8992da44c6805d53 ("auxdisplay: ht16k33: Driver for LED controller") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Robin van der Gracht <robin@protonic.nl> Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
While writing an empty string to a device attribute is a no-op, and thus
does not need explicit safeguards, the user can still write a single
newline to an attribute file:
echo > .../message
If that happens, img_ascii_lcd_display() trims the newline, yielding an
empty string, and causing an infinite loop in img_ascii_lcd_scroll().
Fix this by adding a check for empty strings. Clear the display in case
one is encountered.
Fixes: 0cad855fbd083ee5 ("auxdisplay: img-ascii-lcd: driver for simple ASCII LCD displays") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
AT_XDMAC_CC_PERID() should be used to setup bits 24..30 of XDMAC_CC
register. Using it without parenthesis around 0x7f & (i) will lead to
setting all the time zero for bits 24..30 of XDMAC_CC as the << operator
has higher precedence over bitwise &. Thus, add paranthesis around
0x7f & (i).
Previously, if del_mtd_device() failed with -EBUSY due to a non-zero
usecount, a subsequent call to attempt the deletion again would try to
remove a debugfs directory that had already been removed and panic.
With this change the second call can instead proceed safely.
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
When op_alloc() returns NULL to new_op, no error return code of
orangefs_revalidate_lookup() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Fixes: 8bb8aefd5afb ("OrangeFS: Change almost all instances of the string PVFS2 to OrangeFS.") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Partially revert commit 2ce209c42c01 ("NFS: Wait for requests that are
locked on the commit list"), since it can lead to deadlocks between
commit requests and nfs_join_page_group().
For now we should assume that any locked requests on the commit list are
either about to be removed and committed by another task, or the writes
they describe are about to be retransmitted. In either case, we should
not need to worry.
Fixes: 2ce209c42c01 ("NFS: Wait for requests that are locked on the commit list") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org Fixes: 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
drivers/gpu/drm/drm_plane_helper.c: In function 'drm_primary_helper_update':
drivers/gpu/drm/drm_plane_helper.c:113:32: error: 'visible' is used uninitialized [-Werror=uninitialized]
113 | struct drm_plane_state plane_state = {
| ^~~~~~~~~~~
drivers/gpu/drm/drm_plane_helper.c:178:14: note: 'visible' was declared here
178 | bool visible;
| ^~~~~~~
cc1: all warnings being treated as errors
visible is an output, not an input. in practice this use might turn out
OK but it's still UB.
Fixes: df86af9133b4 ("drm/plane-helper: Add drm_plane_helper_check_state()") Reviewed-by: Simon Ser <contact@emersion.fr> Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca> Signed-off-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20211007063706.305984-1-alex_y_xu@yahoo.ca Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
_nfs4_pnfs_v3/v4_ds_connect do
some work
smp_wmb
ds->ds_clp = clp;
And nfs4_ff_layout_prepare_ds currently does
smp_rmb
if(ds->ds_clp)
...
This patch places the smp_rmb after the if. This ensures that following
reads only happen once nfs4_ff_layout_prepare_ds has checked that data
has been properly initialized.
clang static analysis reports this representative problem:
label.c:1463:16: warning: Assigned value is garbage or undefined
label->hname = name;
^ ~~~~
In aa_update_label_name(), this the problem block of code
if (aa_label_acntsxprint(&name, ...) == -1)
return res;
On failure, aa_label_acntsxprint() has a more complicated return
that just -1. So check for a negative return.
It was also noted that the aa_label_acntsxprint() main comment refers
to a nonexistent parameter, so clean up the comment.
Fixes: f1bd904175e8 ("apparmor: add the base fns() for domain labels") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c09795 ("power: bq27xxx_battery: Reorganize I2C into a module") Cc: Andrew F. Davis <afd@ti.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463f6a236 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The wait_for_completion_timeout function returns 0 if timed out or a
positive value if completed. Hence, "less than zero" comparison always
misses timeouts and doesn't kill the URB as it should, leading to
re-sending it while it is active.
Fixes: 42337b9d4d95 ("HID: add driver for U2F Zero built-in LED and RNG") Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The previous commit fixed handling of incomplete packets but broke error
handling: offsetof returns an unsigned value (size_t), but when compared
against the signed return value, the return value is interpreted as if
it were unsigned, so negative return values are never less than the
offset.
To make the code easier to read, calculate the minimal packet length
once and separately, and assign it to a signed int variable to eliminate
unsigned math and the need for type casts. It then becomes immediately
obvious how the actual data length is calculated and why the return
value cannot be less than the minimal length.
Fixes: 22d65765f211 ("HID: u2fzero: ignore incomplete packets without data") Fixes: 42337b9d4d95 ("HID: add driver for U2F Zero built-in LED and RNG") Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Some registers had wrong default values in cs42l42_reg_defaults[].
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20211015133619.4698-4-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a060 ("ARM: dts: stm32: add sai support on stm32mp157c") Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ld: drivers/staging/ks7010/ks_hostif.o: in function `michael_mic.constprop.0':
ks_hostif.c:(.text+0x95b): undefined reference to `crypto_alloc_shash'
ld: ks_hostif.c:(.text+0x97a): undefined reference to `crypto_shash_setkey'
ld: ks_hostif.c:(.text+0xa13): undefined reference to `crypto_shash_update'
ld: ks_hostif.c:(.text+0xa28): undefined reference to `crypto_shash_update'
ld: ks_hostif.c:(.text+0xa48): undefined reference to `crypto_shash_finup'
ld: ks_hostif.c:(.text+0xa6d): undefined reference to `crypto_destroy_tfm'
The error flow fixed in this patch is not possible because all kernel
users of create QP interface check that device supports steering before
set IB_QP_CREATE_NETIF_QP flag.
Fixes: c1c98501121e ("IB/mlx4: Add support for steerable IB UD QPs") Link: https://lore.kernel.org/r/91c61f6e60eb0240f8bbc321fda7a1d2986dd03c.1634023677.git.leonro@nvidia.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili Fixes: 5036f0a0ecd3 ("[SCSI] csiostor: Fix sparse warnings.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334cec ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK") Reported-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently, at91 pmc driver always register the syscore_ops whatever
the status of the pmc node that has been found. When set as secure
and disabled, the pmc should not be accessed or this will generate
abort exceptions.
To avoid this, add a check on node availability before registering
the syscore operations.
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fbdd ("driver/memory:Move Freescale IFC driver to a common driver") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
The position reporting on Intel Skylake and later chips via
azx_get_pos_skl() contains a udelay(20) call for the capture streams.
A call for this alone doesn't sound too harmful. However, as the
pointer PCM ops is one of the hottest path in the PCM operations --
especially for the timer-scheduled operations like PulseAudio -- such
a delay hogs CPU usage significantly in the total performance.
The code there was taken from the original code in ASoC SST Skylake
driver blindly. The udelay() is a workaround for the case where the
reported position is behind the period boundary at the timing
triggered from interrupts; applications often expect that the full
data is available for the whole period when returned (and also that's
the definition of the ALSA PCM period).
OTOH, HD-audio (legacy) driver has already some workarounds for the
delayed position reporting due to its relatively large FIFO, such as
the BDL position adjustment and the delayed period-elapsed call in the
work. That said, the udelay() is almost superfluous for HD-audio
driver unlike SST, and we can drop the udelay().
Though, the current code doesn't guarantee the full period readiness
as mentioned in the above, but rather it checks the wallclock and
detects the unexpected jump. That's one missing piece, and the drop
of udelay() needs a bit more sanity checks for the delayed handling.
This patch implements those: the drop of udelay() call in
azx_get_pos_skl() and the more proper check of hwptr in
azx_position_ok(). The latter change is applied only for the case
where the stream is running in the normal mode without
no_period_wakeup flag. When no_period_wakeup is set, it essentially
ignores the period handling and rather concentrates only on the
current position; which implies that we don't need to care about the
period boundary at all.
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
Fixes: ef2f826c8f2f ("MIPS: Loongson-3: Enable the COP2 usage") Suggested-by: Huacai Chen <chenhuacai@kernel.org> Reviewed-by: Huacai Chen <chenhuacai@kernel.org> Reported-by: k2ci robot <kernel-bot@kylinos.cn> Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
dc395x_init_one()->adapter_init() might fail. In this case, the acb is
already cleaned up by adapter_init(), no need to do that in
adapter_uninit(acb) again.
This went unnoticed until commit 7897b071ac3b ("net: macb: convert
to phylink") which tickled the problem. The sama5d3 emac has never
been capable of rgmii, and it all just happened to work before that
commit.
Fixes: 21dd0ece34c2 ("ARM: dts: at91: add devicetree for the Axentia TSE-850") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/ea781f5e-422f-6cbf-3cf4-d5a7bac9392d@axentia.se Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VDDCPU pwm regulator to 12V regulator supply
instead of dummy regulator.
[ 11.602281] pwm-regulator regulator-vddcpu: Looking up pwm-supply property
in node /regulator-vddcpu failed
[ 11.602344] VDDCPU: supplied by regulator-dummy
[ 11.602365] regulator-dummy: could not add device link regulator.11: -ENOENT
[ 11.602548] VDDCPU: 721 <--> 1022 mV at 1022 mV, enabled
Fixes: e9bc0765cc12 ("arm64: dts: meson-g12a: enable DVFS on G12A boards") Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210919202918.3556-2-linux.amoon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to YAML validation, and for a future patchset putting this
xo_board reference clock to use as VCO reference parent, add the missing
clock to dsi_phy0.
As can be seen in RK3328's TRM the register range for the GPU is
0xff300000 to 0xff330000.
It would (and does in vendor kernel) overlap with the registers of
the HEVC encoder (node/driver do not exist yet in upstream kernel).
See already existing h265e_mmu node.
If adapter's resetting bit is on, discard the packet but don't stop the
transmit queue - instead leave that to the reset code. With this change,
it is possible that we may get several calls to ibmvnic_xmit() that simply
discard packets and return.
But if we stop the queue here, we might end up doing so just after
__ibmvnic_open() started the queues (during a hard/soft reset) and before
the ->resetting bit was cleared. If that happens, there will be no one to
restart queue and transmissions will be blocked indefinitely.
This can cause a TIMEOUT reset and with auto priority failover enabled,
an unnecessary FAILOVER reset to less favored backing device and then a
FAILOVER back to the most favored backing device. If we hit the window
repeatedly, we can get stuck in a loop of TIMEOUT, FAILOVER, FAILOVER
resets leaving the adapter unusable for extended periods of time.
Fixes: 7f5b030830fe ("ibmvnic: Free skb's in cases of failure in transmit") Reported-by: Abdul Haleem <abdhalee@in.ibm.com> Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit c6af0c227a22 ("ip: support SO_MARK cmsg")
added propagation of SO_MARK from cmsg to skb->mark.
For IPv4 and raw sockets the mark also affects route
lookup, but in case of IPv6 the flow info is
initialized before cmsg is parsed.
Fixes: c6af0c227a22 ("ip: support SO_MARK cmsg") Reported-and-tested-by: Xintong Hu <huxintong@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
These three events can race when pcrypt is used multiple times in a
template ("pcrypt(pcrypt(...))"):
1. [taskA] The caller makes the crypto request via crypto_aead_encrypt()
2. [kworkerB] padata serializes the inner pcrypt request
3. [kworkerC] padata serializes the outer pcrypt request
3 might finish before the call to crypto_aead_encrypt() returns in 1,
resulting in two possible issues.
First, a use-after-free of the crypto request's memory when, for
example, taskA writes to the outer pcrypt request's padata->info in
pcrypt_aead_enc() after kworkerC completes the request.
Second, the outer pcrypt request overwrites the inner pcrypt request's
return code with -EINPROGRESS, making a successful request appear to
fail. For instance, kworkerB writes the outer pcrypt request's
padata->info in pcrypt_aead_done() and then taskA overwrites it
in pcrypt_aead_enc().
Avoid both situations by delaying the write of padata->info until after
the inner crypto request's return code is checked. This prevents the
use-after-free by not touching the crypto request's memory after the
next-inner crypto request is made, and stops padata->info from being
overwritten.
Fixes: 5068c7a883d16 ("crypto: pcrypt - Add pcrypt crypto parallelization wrapper") Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
For each rate change command submission, the FW has to do a phy
power off sequence internally. For this to happen correctly, the
PLL re-initialization control setting has to be turned off before
sending mailbox commands and re-enabled once the command submission
is complete.
Without the PLL control setting, the link up takes longer time in a
fixed phy configuration.
Fixes: 47f164deab22 ("amd-xgbe: Add PCI device support") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Benjamin Li <benl@squareup.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: 876c9d3aeb98 ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-3-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: c305a19a0d0a ("libertas_tf: usb specific functions") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-2-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If handle_sske cannot set the storage key, because there is no
page table entry or no present large page entry, it calls
fixup_user_fault.
However, currently, if the call succeeds, handle_sske returns
-EAGAIN, without having set the storage key.
Instead, retry by continue'ing the loop without incrementing the
address.
The same issue in handle_pfmf was fixed by a11bdb1a6b78 ("KVM: s390: Fix pfmf and conditional skey emulation").
Use the actual return value instead of always -1 if register_kretprobe()
failed.
E.g. without this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Operation not permitted
With this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Unknown symbol in module
Link: https://lkml.kernel.org/r/1635213091-24387-2-git-send-email-yangtiezhu@loongson.cn Fixes: 804defea1c02 ("Kprobes: move kprobe examples to samples/") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
v1: Implement a more general statement as recommended by Eric Dumazet. The
sequence number will be advanced, so this check will fix the FIN case and
other cases.
A customer reported sockets stuck in the CLOSING state. A Vmcore revealed that
the write_queue was not empty as determined by tcp_write_queue_empty() but the
sk_buff containing the FIN flag had been freed and the socket was zombied in
that state. Corresponding pcaps show no FIN from the Linux kernel on the wire.
Some instrumentation was added to the kernel and it was found that there is a
timing window where tcp_sendmsg() can run after tcp_send_fin().
tcp_remove_empty_skb() will then free the FIN sk_buff as "skb->len == 0". The
TCP socket is now wedged in the FIN-WAIT-1 state because the FIN is never sent.
If the other side sends a FIN packet the socket will transition to CLOSING and
remain that way until the system is rebooted.
Fix this by checking for the FIN flag in the sk_buff and don't free it if that
is the case. Testing confirmed that fixed the issue.
Fixes: fdfc5c8594c2 ("tcp: remove empty skb from write queue in error cases") Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Reported-by: Monir Zouaoui <Monir.Zouaoui@mail.schwarz> Reported-by: Simon Stier <simon.stier@mail.schwarz> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2baa1de7a ("irqchips/bmips: Add bcm6345-l1 interrupt controller") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
... otherwise we will try unlocking a spinlock that was never locked via a
garbage pointer.
At the time we reach this code path, we usually successfully looked up
a PGSTE already; however, evil user space could have manipulated the VMA
layout in the meantime and triggered removal of the page table.